控制计划中英文版

6.Boring hole 镗孔

Boring tool 镗刀18Hole diameter 孔径Rev 转速3000rad/min

F进刀量=0.02mm/r

Φ12.2+0.04/0Ping gauge 塞规(UGZ-***-0001/UGZ-***-

0001)

3pcs/ Machine start up or

Change tool

3pcs/3H AQL1.0 C=0

1.Inspection report (PIR A01-

002)

2.SPC control

1.检验报告(报告编号：A01-002)

2.SPC控制

37Jumpness全跳动0.02Concentricity Gage同轴度仪

(19753-A-10P)3pcs/ Machine start up or

Change tool

3pcs/3H AQL1.0 C=0

Inspection report (PIR A01-002)

检验报告(报告编号：A01-002)

7.Turning Outside Diameter 车外圆

Turning tool 车刀4Outside diameter 外径Rev 转速2500rad/min

Φ14.03

Projector 投影仪(490127)

3pcs/ Machine start up or Change tool

1pcs/3H

AQL1.5 C=0Inspection report (PIR A01-002)

检验报告(报告编号：A01-002)Inspection report (PIR A01-Chamfer 倒角F 进刀量=0.03mm/r

1.4

±0.015

Projector 投影仪(490127)3pcs/ Machine start up or Change tool 3只/开机和换刀

3pcs/3H

AQL1.0 C=0 1.Inspection report (PIR A01-002)

2.SPC control

1.检验报告(报告编号：A01-002)

2.SPC 控制5Outside diameter 外径

Φ12.6

±0.03

Projector 投影仪(490127)3pcs/ Machine start up or Change tool

1pcs/3H

AQL1.5 C=0

Inspection report (PIR A01-002)检验报告(报告编号：A01-002)

1Outside diameter 外径

Φ16.18

0/-0.04

Micrometer 千分尺(0~25mm)451384833pcs/ Machine start up or

Change tool 3只/开机和换

刀

3pcs/3H

AQL1.0 C=0 1.Inspection report (PIR A01-002)

2.SPC control

1.检验报告(报告编号：A01-002)

2.SPC 控制25

Angle 角度

45.6°

±5°

Projector 投影仪(490127)

3pcs/ Machine start up or Change tool

1pcs/3H AQL1.5 C=0Inspection report (PIR A01-002)检验报告(报告编号：A01-002)8.Cutting Groove 割槽

Cutting tool 切断刀

2Outside diameter 外径Rev 转速2500rad/min Ф 14+0.05Micrometer 千分尺(0~25mm)451384833pcs/ Machine start up or Change tool

1pcs/3H AQL1.5 C=0Inspection report (PIR A01-002)检验报告(报告编号：A01-002)38Roughness 粗糙度F 进刀量=0.03mm/r

Ra1.6Roughness Tester 粗糙度仪DTS03A 3pcs/ Machine start up or Change tool

1pcs/3H AQL1.5 C=0Inspection report (PIR A01-002)检验报告(报告编号：A01-002)11Width 宽度 2.2 +0.2/0Height Tester0~30mm(01194)高度规3pcs/ Machine start up or Change tool

1pcs/3H AQL1.5 C=0Inspection report (PIR A01-002)检验报告(报告编号：A01-002)8Length 长度11.8

±0.2

Projector 投影仪(490127)3pcs/ Machine start up or Change tool

1pcs/3H AQL1.5 C=0Inspection report (PIR A01-002)检验报告(报告编号：A01-002)41Angle 角度3°

±1°Projector 投影仪(490127)3pcs/ Machine start up or Change tool

1pcs/3H AQL1.5 C=0Inspection report (PIR A01-002)检验报告(报告编号：A01-002)26

Radius 圆弧R0.1 +0.1(2X)Projector 投影仪(490127)

3pcs/ Machine start up or Change tool

1pcs/3H AQL1.5 C=0Inspection report (PIR A01-002)检验报告(报告编号：A01-002)9.Cutting off 切断Cutting tool 切断刀17Length 长度Rev 转速2500rad/min F 进刀量=0.03mm/r 23.4±

0.1

Height Tester0~30mm(01194)高度规

3pcs/ Machine start up or Change tool

1pcs/3H AQL1.5 C=0Inspection report (PIR A01-002)检验报告(报告编号：A01-002)10.Drilling hole 钻孔

Drilling tool 钻头

22Inside diameter 外径Rev 转速2500rad/min Φ6+0.1Ping gauge 塞规(UGZ-***-0001/UGZ-***-0001)3pcs/ Machine start up or

Change tool 1pcs/3H AQL1.5 C=0Inspection report (PIR A01-002)检验报告(报告编号：A01-002)36Concentricity 同轴度Φ0.02Concentricity Gage 同轴度仪(19753-A-10P)

3pcs/ Machine start up or Change tool

3pcs/3H AQL1.0 C=0Inspection report (PIR A01-002)检验报告(报告编号：A01-002)40Roughness 粗糙度F 进刀量=0.03mm/r Ra6.3Roughness Tester 粗糙度仪DTS03A 3pcs/ Machine start up or Change tool

1pcs/3H AQL1.5 C=0Inspection report (PIR A01-002)检验报告(报告编号：A01-002)14Length 长度9

±0.25

Projector 投影仪(490127)3pcs/ Machine start up or Change tool

1pcs/3H AQL1.5 C=0Inspection report (PIR A01-002)检验报告(报告编号：A01-002)33Angle 角度118°

±3°

Contracer 轮廓仪(DD-0009)3pcs/ Machine start up or Change tool

1pcs/3H AQL1.5 C=0Inspection report (PIR A01-002)检验报告(报告编号：A01-002)31

Chamfer 倒角0.2 +0.2/0.1*45Projector 投影仪(490127)

3pcs/ Machine start up or Change tool

1pcs/3H

AQL1.5 C=0

Inspection report (PIR A01-002)检验报告(报告编号：A01-002)11.Drilling hole 钻孔

Drilling tool 钻头Hole diameter 孔径Rev 转速2500rad/min F 进刀量=0.03mm/r Φ10Process technice size 过程工艺尺寸

12.Boring Hole 镗孔

Boring tool 镗刀

23Inside diameter 外径Rev 转速3000rad/min F 进刀量=0.02mm/r Φ8.8±0.1Ping gauge 塞规(UGZ-***-0001/UGZ-***-0001)

3pcs/ Machine start up or

Change tool 1pcs/3H AQL1.5 C=0Inspection report (PIR A01-002)检验报告(报告编号：A01-002)30Chamfer 倒角0.1*45°Projector 投影仪(490127)

3pcs/ Machine start up or Change tool

1pcs/3H AQL1.5 C=0Inspection report (PIR A01-002)检验报告(报告编号：A01-002)13highness 高度 2.5+0.2

Height Tester0~30mm(01194)高度规3pcs/ Machine start up or Change tool

1pcs/3H AQL1.5 C=0Inspection report (PIR A01-002)检验报告(报告编号：A01-002)12highness 高度 1.2

±0.025

Height Tester0~30mm(01194)高度规3pcs/ Machine start up or Change tool

1pcs/3H AQL1.5 C=0Inspection report (PIR A01-002)检验报告(报告编号：A01-002)35parallel 平行度0.02Dial indicator 千分表

3pcs/ Machine start up or Change tool

3pcs/3H AQL1.5 C=0Inspection report (PIR A01-002)检验报告(报告编号：A01-002)24

Inside diameter 外径Φ13 +0.04Ping gauge 塞规(UGZ-***-0001/UGZ-***-0001)3pcs/ Machine start up or

Change tool 3pcs/3H AQL1.0 C=0Inspection report (PIR A01-002)检验报告(报告编号：A01-002)Turning tool 车刀

6Outside diameter 外径Rev 转速2500rad/min Φ14.6+0.1Micrometer 千分尺(0~25mm)451384833pcs/ Machine start up or

Change tool

1pcs/3H AQL1.5 C=0Inspection report (PIR A01-002)检验报告(报告编号：A01-002)39Roughness 粗糙度F进刀量=0.03mm/r Ra1.6Roughness Tester 粗糙度仪DTS03A

3pcs/ Machine start up or Change tool

1pcs/3H AQL1.5 C=0Inspection report (PIR A01-002)检验报告(报告编号：A01-002)28Chamfer 倒角0.2±0.05

*45°

Projector 投影仪(490127)

3pcs/ Machine start up or Change tool

1pcs/3H AQL1.5 C=0Inspection report (PIR A01-002)检验报告(报告编号：A01-002)9highness 高度 3.8

+0.1

Height Tester0~30mm(01194)高度规3pcs/ Machine start up or Change tool

1pcs/3H AQL1.5 C=0Inspection report (PIR A01-002)检验报告(报告编号：A01-002)29

Chamfer 倒角

0.2±0.1*45°

Projector 投影仪(490127)

3pcs/ Machine start up or Change tool

1pcs/3H

AQL1.5 C=0

Inspection report (PIR A01-002)检验报告(报告编号：A01-002)

13.Turning Outside Diameter 车外圆