嘉陵摩托车保养(Jialing Motorcycle maintenance)

嘉陵摩托车保养（Jialing Motorcycle maintenance）Maintenance of air filter

The air cleaner filter element should be cleaned after running in, and often on the dusty road, the number of cleaning should be increased. The steps are as follows:

1. Remove the right cover. Remove the five air cleaner housing fixing screws. Remove the air filter housing cover and remove the filter

2. Put the filter core in the cleaning agent and wash it and let it dry

3. Spray the dry filter into 15W/40QE oil, knead it evenly, and then squeeze out too much oil

4. Assemble in reverse order

5, with the right cover, we should pay attention to: 1, paper filter element, each exercise 8000KM to be replaced, 2, JH70, JL90 for paper filter, compressed air blowing dust

Maintenance and maintenance of brake equipment

I. adjustment of drum front brakes

A, a main bracket, measured from the free position to start braking, free travel before the brake handle is 10 ~ 20MM

B, if not in the specified range, should be adjusted, adjust

the front brake nut clockwise, reduce the free stroke; adjust the front brake nut counterclockwise, increase the free stroke

C, hold several times along the front brake brake handle, and then relax, check the front brake work is good (turn the front wheel front wheel rotation is flexible)

The D can also be adjusted by the front brake trim nut

Note: the brake shoes shall be replaced if the indicator on the front brake is aligned with the scale on the end cover of the brake.

The shoe should be replaced every 4000KM

Each drive 2000KM, clutch control line cleaning and lubrication

Two, the adjustment of the rear brake

A, support motorcycle with main support

B, after measuring the brake pedal from the original position of the brake to start the work of the journey is 20 ~ 30MM

C, need to be adjusted, with brake adjustment method

Storage battery maintenance

Remove left cover

Batteries for new cars should be added between electrolyte

first and bottom

Recharge the new battery, the use of better results

Available 0.1A current, charge 6~7 hours

Available 0.3A current, charge 3~4 hours

Always check the battery, if the level is below the minimum scale, should add distilled water to the specified value for battery or long time when not in use, should be charging note: when charging will produce hydrogen and oxygen, charging site is strictly prohibited fireworks

Running in of motorcycle

The running mileage of the new car is 1000KM. It should be run in accordance with the requirements of the instruction manual and extend its service life:

1. Control the speed

2 control load, should control the load in the maximum load of less than 2/3

3, control travel time, every 0.5 hours after exercise, should let the engine flameout, cooling 10 minutes

4, frequently change the oil, it is recommended during the running period, each exercise 300KM change oil

Check and adjust the throttle operation section

First, the gas check and maintenance

Turn the accelerator handle and check that the return is good. If it is stuck or unable to return, it should be maintained

Step 1: remove the reflector

2, remove the tanker seat, take off the throttle, control line and tanker

3, to add a little throttle operating line of lubricating oil, to smear a grease lubricator

4, in accordance with the reverse order, you can note: the throttle line should be cleaned every 2000KM, lubrication once.

Two, throttle handle free stroke adjustment

The free stroke of the accelerator handle is 2 to 6mm, and should be adjusted if not in accordance with the regulations

The steps are as follows: loosen the lock nut, turn the throttle adjusting screw to the specified position, and then tighten the lock nut, rotate clockwise the throttle adjusting screw pipe, throttle free travel becomes smaller; the counterclockwise rotation of the throttle adjusting screw pipe, larger throttle free travel.

Adjustment of carburetor idle speed

1 switch on the ignition and preheat for 5~10 minutes

2, remove the right cover, clockwise rotating idle screws, the engine idle rise, counterclockwise rotation idle screws, the engine idle speed down

3, adjust the idle speed to about 1500R/MIN

Attention: air mixing ratio screw has been raised on special instrument at the factory. Please don't adjust it easily. If necessary, please go to the Jialing station and ask professional technicians to adjust it.

Clutch adjustment

The left hand handle of the clutch is operated at 10 to 20MM, if not in this range, please adjust the steps as follows:

1. Loosen the clutch and adjust the lock nut

2. Turn the adjusting screw clockwise, increase the free clearance of the clutch, turn the adjusting screw counterclockwise, reduce the free clearance of the clutch

3. Tighten the clutch and adjust the lock nut

Caution: the clutch control line shall be removed and cleaned and lubricated at 2000 KM each time

Inspection, adjustment and lubrication of drive chain

1, inspection method, with the main support support motorcycle, step on the speed change pedal into neutral position, the chain up and down swing, check its swing range should be in 10 ~ 20MM, if not in this range, should be adjusted

2, adjustment method

A, loosen the rear axle lock nut and loosen the brake adjustment nut

B, unscrew the chain adjuster locknut

C, rotate the adjusting bolt clockwise, reduce the swing of the chain, adjust the bolt counter clockwise, increase the swing of the chain, and adjust the swing of the chain to the range of 10 ~ 20MM

Note: the left and right chain adjuster scales should be the same

If adjusted, the scale of the chain adjuster is in the last grid, indicating the excessive wear of the chain transmission parts, and the big, small chain wheels and chains shall be replaced

D, check the tightness of the chain, tighten the adjusting bolts of the chain regulator first, and then tighten the wheel axle to lock the nut

If the chain is found to lack oil, it should be lubricated. Under normal circumstances, every 500KM should be cleaned and

lubricated once

Steps are as follows:

1 remove the shift arm

2. Remove the left rear cover of the engine

3, remove the back chain box

4, find the movable link, use pliers to remove the movable locking clip, remove the chain from the backward direction, put the chain into the cleaning agent, wash, and then dry. Check the wear of the chain and replace it if necessary.

Note: the direction of the opening of the locking block shall be opposite to the movement of the chain

5, in reverse order, and put on the chain of proper amount of lubricating oil

Inspection and replacement of engine oil

Check the oil and oil level before starting the car every day

1. Put the motorcycle on the ground and support with the main support

2, loosen the oil scale, to see whether the oil level in the upper and lower scales, such as the oil volume is too small, should be the prescribed oil change lubricating oil and

cleaning filter

1. Preheat the engine for 2-3 minutes and turn off the engine

2. Place an oil tank under the engine

3, unscrew the oil drain hole, oil hole is removed, remove the oil filter net, spring

The 4 step, recoil starter several times to discharge all disabled oil

5, the spring and a filter net, put into the cleaning agent cleaning oil hole

6. Check type 0 sealing ring, filter screen is in good condition, if damaged, should be replaced, and then in reverse order with disassembly

7, inject new oil in the upper and lower calibration line, note: new car running in period should be replaced 3 times oil.

Inspection and replacement of spark plugs

1, remove the spark plug cap, remove the surrounding debris

2. Remove the spark plug with the spark plug sleeve fitted with the car

3. Remove the spark plugs with iron brazing and remove the debris from the spark plugs with a brush

4, check the spark plug electrode is ablation, if there is ablation, should replace the spark plug

5, with a thickness gauge to check the spark plug gap, the spark gap adjustment for 0.6-0.7mm

6. Check the gasket on the spark plug. If it is seriously deformed or broken, replace it

7, check the spark: foot start the engine and check the Spark Spark for blue and white color

8, when the spark plug is tightened, in order to prevent thread disorder, should first hand to plug the spark plug in place, and then use the spark plug sleeve tightening.

Replacement of pipe

The safety tube is located next to the battery, and replace it with the same specification,

If the pipe is often burned out, usually short circuit or overload, please ask the Jialing maintenance personnel for inspection.

The use of pipes that do not meet specifications can cause severe consequences or even fire on the circuit system.

When checking and changing the safety pipe, the ignition switch should be put off to prevent the short circuit.

Adjustment of direction of headlamp irradiation

Insert the screwdriver in the small hole in the rear panel of the front shade and adjust the headlight adjusting screw

Adjust the screw light clockwise and turn the light higher

Turn the adjusting screws counter clockwise, and the light is low

Adjustment of rear brake switch

After the recoil pedal is started, the rear brake light should turn on. If it is bright or not, it should be adjusted:

1. Turn ignition switch to ON position

2. Turn the adjusting nut clockwise, brake ahead, turn the counter clockwise, adjust the nut and delay the brake light

Vehicle cleaning

In order to maintain the quality of the vehicle, it should be cleaned regularly to check for any damage or oil leakage

1, after cleaning, use a lot of clean water for the whole car cleaning, cleaning, electrical switches, instruments, muffler exports

2. Dry the motorcycle, start the engine, and let it warm for

a few minutes

3, lubrication drive chain, before the road to do brake experiment, let it return to normal state

Attention: after cleaning, the braking performance of the motorcycle has been reduced

Storage of vehicles

Vehicles are not used for a long time, the time is more than 1 months to do the following work:

1. Clean and dry the motorcycle, wax the car body, and lubricate the parts that are easy to rust

2. Release the fuel from the carburetor

3, take off the spark plug, to the cylinder into 15 ~ 20ML lubricating oil

4, remove the battery, placed in dry, ventilated, avoid direct sunlight place

5. Inflate the tire to the specified air pressure and place it on the cushion block

6, articles of cloth or strong ventilation cover of motorcycle, a motorcycle parked in the small local ventilation, temperature difference

The use of vehicles after storage

1. Remove the motorcycle cover

2, check the battery voltage, such as voltage is too low, should be recharged

3. Add fresh fuel

4. Check before driving and check if the performance is normal