注塑英语
注塑专业英语1(2008-05-19 16:47:33)
标签：文化
分类：注塑技术文件
钣金machine cover / upper cover/ side cover 锁模部分clamping unit
射胶部分injection unit
机架machine frame / base
电气系统electric system
液压系统hydraulic system
机械系统mechanical system
机门safety door / fixed door / movable door 锁模部分clamping unit
电脑控制器computer controller
机械安全锁mechanical safety interlock
射胶部分injection unit
液压系统hydraulic system
电箱electrical cabinet / cable
机架分体线stand split line
机架螺丝孔foundation bolt hole
机架machine base / supporting frame
理论注射容积theoretical shot volume
实际注射量shot weight
螺杆直径screw diameter
注射压力injection pressure
注射速度injection speed
注射速率injection rate
螺杆长径比screw L/D ratio
螺杆行程screw stroke
螺杆转速screw speed
熔胶能力plasticizing capacity
锁模力clamping force
开模/锁模行程mold clamping / opening stroke
模板尺寸platen size
拉杆间距distance between tie bars / rods
模板最大距离max. daylight
容模量mold thickness (min. & max.)
顶出行程hydraulic ejection stroke
顶出力hydraulic ejection force
顶针数nos. of ejector pin
液压系统压力hydraulic system pressure
油泵马达pump motor
电热量heating capacity
温度控制区数nos. of temp control zones 射嘴接触力nozzle contact force
Injection 射出
Cooling time 冷却时间
Holding time 锁模时间
Injection alarm time 射出警报时间Injection start delay
Final cushion minimum value
Change-over to holding by value Plasticizing end value
Hydrarlic change-over pressure holding Screwvalue for change-over to holding Change-over to holding by enable value Hydraulic pressure in holding 锁模压力Filling stage pressure limit
Injection speed 射出速度
Injection注射
Cooling time冷却时间
Holding time
Injection alarm time注射报警时间Injection start delay注射开始延时
Final cushion minimum value最后段位置Change-over to holding by value切换到锁模Plasticizing end value预塑重终点Hydrarlic change-over pressure holding切换到保压
Screwvalue for change-over to holding加料Change-over to holding by enable value Hydraulic pressure in holding锁模力
Filling stage pressure limit充模压力Injection speed注射速度
Plasticizing delay预塑延时
1st suck-back speed储料一速度
1st suck-back pressure储料一压力Screwrotation speed螺杆转速Decompression value at end of injection注射终点
Decompression value at end of plasticizing预塑终点
Mould closing关模
Mould close force关模压力
Mould closing safety time .. 时间Mould closing pressure .. 压力
1st closing safety stage pressure合模一段压力
1st mould closing speed ...成型速度
1st stage mould closing speed
1st stage mould closing safety position.....位置（？）
High pressure start position高压锁模位置Number of repeat mould closing movement..重复次数
Holding time 保压时间
Injection start delay 注射延迟
Injection注射
Cooling time冷却时间
Holding time保压时间
Injection alarm time注射报警时间
Injection start delay注射开始延时(注射延时启动延时)
Final cushion minimum value最后段位置（最小余量）
Change-over to holding by value切换到锁模（保压由位置切换）
Plasticizing end value预塑重终点（熔胶终止）
Hydrarlic change-over pressure holding切换到保压
Screwvalue for change-over to holding加料Change-over to holding by enable value保压由位置切换
Hydraulic pressure in holding锁模力（保压）Filling 填充
Injection alarm time 射胶时间
Injection start delay 延迟射胶
塑件模具相关英文——1
compre sion molding压缩成型
flash mold溢流式模具
plsitive mold挤压式模具
split mold分割式模具
cavity型控母模
core模心公模
taper锥拔
leather cloak仿皮革
shiver饰纹
flow mark流痕
welding mark溶合痕
post screw insert螺纹套筒埋值
self tapping screw自攻螺丝striper plate脱料板
piston活塞
cylinder汽缸套
chip细碎物
handle mold手持式模具
encapsulation molding低压封装成型、射出成型用模具
two plate两极式（模具）
well type蓄料井
insulated runner绝缘浇道方式
hot runner热浇道
runner plat浇道模块
valve gate阀门浇口
band heater环带状的电热器
spindle阀针
spear head刨尖头
slag well冷料井
cold slag冷料渣
air vent排气道
welding line熔合痕
模具相关英语——8
stop screw止付螺丝
located pin定位销
outer bush外导套
模板类
top plate上托板（顶板）
top block上垫脚
punch set上模座
punch pad上垫板
punch holder上夹板
stripper pad脱料背板
up stripper上脱料板
male die公模(凸模)
feature die公母模
female die母模(凹模)
upper plate上模板
lower plate下模板
die pad下垫板
die holder下夹板
die set下模座
bottom block下垫脚
bottom plate下托板(底板)
stripping plate内外打(脱料板)
outer stripper外脱料板
inner stripper内脱料板
lower stripper下脱料板
零件类
punch冲头
insert入块(嵌入件)
deburring punch压毛边冲子
groove punch压线冲子
stamped punch字模冲子
round punch圆冲子
special shape punch异形冲子
bending block折刀
roller滚轴
baffle plate挡块
located block定位块
supporting block for location
定位支承块
air cushion plate气垫板
air-cushion eject-rod气垫顶杆trimming punch切边冲子
stiffening rib punch = stinger 加强筋冲子ribbon punch压筋冲子
reel-stretch punch卷圆压平冲子
guide plate定位板
sliding block滑块
模具相关英语——7
emboss凸点
dome凸圆
semi-shearing半剪
stamp mark冲记号
deburr or coin压毛边
punch riveting冲压铆合
side stretch侧冲压平
reel stretch卷圆压平
groove压线
blanking下料
stamp letter冲字(料号)
shearing剪断
tick-mark nearside正面压印
tick-mark farside反面压印
冲压名称类
extension dwg展开图
procedure dwg工程图
die structure dwg模具结构图
material材质material thickness料片厚度factor系数
upward向上
downward向下
press specification冲床规格
die height range适用模高
die height闭模高度
burr毛边
gap间隙
weight重量
total wt.总重量
punch wt.上模重量
五金零件类
inner guiding post内导柱
inner hexagon screw内六角螺钉dowel pin固定销
coil spring弹簧
lifter pin顶料销
eq-height sleeves=spool等高套筒pin销
lifter guide pin浮升导料销guide pin导正销
wire spring圆线弹簧
outer guiding post外导柱
模具相关英语——6
drill钻
boring镗
blinster气泡
fillet镶;嵌边
through-hole form通孔形式voller pin formality滚针形式cam driver铡楔
shank摸柄
crank shaft曲柄轴
augular offset角度偏差
velocity速度
production tempo生产进度现状torque扭矩
spline=the multiple keys花键quenching淬火
tempering回火
annealing退火
carbonization碳化
alloy合金
tungsten high speed steel钨高速的moly high speed steel钼高速的organic solvent有机溶剂bracket小磁导
liaison联络单
volatile挥发性
resistance电阻
ion离子
titrator滴定仪
beacon警示灯
coolant冷却液
crusher破碎机
模具工程类
plain die简易模
pierce die冲孔模
forming die成型模
progressive die连续模
gang dies复合模
shearing die剪边模
riveting die铆合模
pierce冲孔
forming成型(抽凸,冲凸)
draw hole抽孔
bending折弯
trim切边
模具相关英语——5
spare parts=buffer备品coordinate坐标
dismantle the die折模
auxiliary fuction辅助功能
poly-line多义线
heater band 加热片thermocouple热电偶
sand blasting喷沙
grit 砂砾
derusting machine除锈机degate打浇口
dryer烘干机
induction感应
induction light感应光
response=reaction=interaction感应ram连杆
edge finder巡边器
concave 凹convex凸
short射料不足
nick缺口
speck瑕疪
shine亮班
splay 银纹
gas mark焦痕
delamination起鳞
cold slug冷块
blush 导色
gouge沟槽;凿槽
satin texture段面咬花
witness line证示线
patent专利
grit沙砾
granule=peuet=grain细粒
grit maker抽粒机
cushion缓冲
magnalium镁铝合金magnesium镁金
metal plate钣金
lathe车
mill锉
plane刨
grind磨
模具相关英语——4
baffle plate挡块
cover plate盖板
male die公模
female die母模
groove punch压线冲子
air-cushion eject-rod气垫顶杆spring-box eject-plate弹簧箱顶板bushing block衬套
insert 入块
club car高尔夫球车
capability能力
parameter参数
factor系数
phosphate皮膜化成
viscosity涂料粘度alkalidipping脱脂
main manifold主集流脉
bezel斜视规
blanking穿落模
dejecting顶固模
demagnetization去磁;消磁
high-speed transmission高速传递
heat dissipation热传
rack上料
degrease脱脂
rinse水洗
alkaline etch龄咬
desmut剥黑膜
D.I. rinse纯水次
Chromate铬酸处理
Anodize阳性处理
seal封孔
revision版次
part number/P/N料号
good products良品
scraped products报放心品
defective products不良品
finished products成品
disposed products处理品
barcode条形码
flow chart流程窗体
assembly组装
stamping冲压
molding成型
模具相关英语——3
difference quantity差异量
cause analysis原因分析
raw materials原料
materials物料
finished product成品
semi-finished product半成品
packing materials包材
good product/accepted goods/ accepted parts/good parts良品
defective product/non-good parts不良品disposed goods处理品
warehouse/hub仓库
on way location在途仓
oversea location海外仓
spare parts physical inventory list备品盘点清单
spare molds location模具备品仓skid/pallet栈板
tox machine自铆机
wire EDM线割
EDM放电机
coil stock卷料
sheet stock片料
tolerance工差
score=groove压线
cam block滑块
pilot导正筒
trim剪外边
pierce剪内边
drag form压锻差
pocket for the punch head挂钩槽
slug hole废料孔
feature die公母模
expansion dwg展开图
radius半径
shim(wedge)楔子
torch-flame cut火焰切割
set screw止付螺丝
form block折刀
stop pin定位销
round pierce punch=die button圆冲子shape punch=die insert异形子
stock locater block定位块
under cut=scrap chopper清角
active plate活动板
模具相关英语——2
steel/rolled steel钢材
material statistics sheet
物料统计明细表
meeting minutes会议记录
meeting type 会别
distribution department分发单位
location地点
chairman主席
present members出席人员
subject主题
conclusion结论
decision items决议事项
responsible department负责单位
pre-fixed finishing date预定完成日approved by / checked by / prepared by核准/
审核/承办
PCE assembly production schedule sheet PCE组装厂生产排配表
model机钟
work order工令
revision版次
remark备注
production control confirmation生产确认checked by初审
approved by核准
department部门
stock age analysis sheet
库存货龄分析表
on-hand inventory现有库存
available material良品可使用
obsolete material良品已呆滞
to be inspected or reworked
待验或重工
total合计
cause description原因说明
part number/ P/N 料号
type形态
item/group/class类别
quality品质
prepared by制表
notes说明
year-end physical inventory difference analysis sheet
年终盘点差异分析表
physical inventory盘点数量
physical count quantity帐面数量
模具相关英语——1
padding block垫块
stepping bar垫条
upper die base上模座
lower die base下模座
upper supporting blank上承板
upper padding plate blank上垫板
spare dies模具备品
spring 弹簧
bolt螺栓
document folder活页夹
file folder资料夹
to put file in order整理资料spare tools location手工备品仓
first count初盘人
first check初盘复棹人
second count 复盘人
second check复盘复核人
equipment设备
waste materials废料
work in progress product在制品
casing = containerazation装箱
quantity of physical invetory second count 复盘点数量
quantity of customs count
会计师盘,点数量
the first page第一联
filed by accounting department for reference 会计部存查
end-user/using unit(department)使用单位summary of year-end physical inventory bills 年终盘点截止单据汇总表
bill name单据名称
This sheet and physical inventory list will be sent to accounting department together (Those of NHK will be sent to financial department) 本表请与盘点清册一起送会计部－(NHK厂区送财会部)
Application status records of year-end physical inventory List and physical inventory card 年终盘点卡与清册使用－状况明细表blank and waste sheet NO.
空白与作废单号
plate电镀
mold成型
material for engineering mold testing工程试模材料
not included in physical inventory不列入盘点
sample样品
incoming material to be inspected进货待验description品名
101个热处理常用英文词汇
1. indication 缺陷
2. test specimen 试样
3. bar 棒材
4. stock 原料
5. billet 方钢，钢方坯
6. bloom 钢坯,钢锭
7. section 型材
8. steel ingot 钢锭
9. blank 坯料，半成品
10. cast steel 铸钢
11. nodular cast iron 球墨铸铁
12. ductile cast iron 球墨铸铁
13. bronze 青铜
14. brass 黄铜
15. copper 合金
16. stainless steel不锈钢
17. decarburization 脱碳
18. scale 氧化皮
19. anneal 退火
20. process anneal 进行退火
21. quenching 淬火
22. normalizing 正火
23. Charpy impact text 夏比冲击试验
24. fatigue 疲劳
25. tensile testing 拉伸试验
26. solution 固溶处理
27. aging 时效处理
28. Vickers hardness维氏硬度
29. Rockwell hardness 洛氏硬度
30. Brinell hardness 布氏硬度
31. hardness tester硬度计
32. descale 除污，除氧化皮等
33. ferrite 铁素体
34. austenite 奥氏体
35. martensite马氏体
36. cementite 渗碳体
37. iron carbide 渗碳体
38. solid solution 固溶体
39. sorbite 索氏体
40. bainite 贝氏体
41. pearlite 珠光体
42. nodular fine pearlite/ troostite屈氏体
43. black oxide coating 发黑
44. grain 晶粒
45. chromium 铬46. cadmium 镉
47. tungsten 钨
48. molybdenum 钼
49. manganese 锰
50. vanadium 钒
51. molybdenum 钼
52. silicon 硅
53. sulfer/sulphur 硫
54. phosphor/ phosphorus 磷
55. nitrided 氮化的
56. case hardening 表面硬化，表面淬硬
57. air cooling 空冷
58. furnace cooling 炉冷
59. oil cooling 油冷
60. electrocladding /plating 电镀
61. brittleness 脆性
62. strength 强度
63. rigidity 刚性,刚度
64. creep 蠕变
65. deflection 挠度
66. elongation 延伸率
67. yield strength 屈服强度
68. elastoplasticity 弹塑性
69. metallographic structure 金相组织
70. metallographic test 金相试验
71. carbon content 含碳量
72. induction hardening 感应淬火
73. impedance matching 感应淬火
74. hardening and tempering 调质
75. crack 裂纹
76. shrinkage 缩孔，疏松
77. forging 锻（件）
78. casting 铸（件）
79. rolling 轧（件）
80. drawing 拉（件）
81. shot blasting 喷丸（处理）
82. grit blasting 喷钢砂（处理）
83. sand blasting 喷砂（处理）
84. carburizing 渗碳
85. nitriding 渗氮
86. ageing/aging 时效
87. grain size 晶粒度
88. pore 气孔
89. sonim 夹砂
90. cinder inclusion 夹渣
91. lattice晶格
92. abrasion/abrasive/rub/wear/wearing resistance (property) 耐磨性
93. spectrum analysis光谱分析
94. heat/thermal treatment 热处理
95. inclusion 夹杂物
96. segregation 偏析
97. picking 酸洗，酸浸
98. residual stress 残余应力
99. remaining stress 残余应力
100. relaxation of residual stress 消除残余应力
101. stress relief 应力释放
模具相关英语(5)
semi-shearing半剪
stamp mark冲记号
deburr or coin压毛边
punch riveting冲压铆合
side stretch侧冲压平
reel stretch卷圆压平
groove压线
blanking下料
stamp letter冲字(料号)
shearing剪断
tick-mark nearside正面压印
tick-mark farside反面压印
冲压名称类
extension dwg展开图
procedure dwg工程图
die structure dwg模具结构图
material材质
material thickness料片厚度
factor系数
upward向上
downward向下
press specification冲床规格
die height range适用模高
die height闭模高度
burr毛边
gap间隙
weight重量
total wt.总重量
punch wt.上模重量五金零件类
inner guiding post内导柱
inner hexagon screw内六角螺钉dowel pin固定销
coil spring弹簧
lifter pin顶料销
eq-height sleeves=spool等高套筒pin销
lifter guide pin浮升导料销guide pin导正销
wire spring圆线弹簧
outer guiding post外导柱
stop screw止付螺丝
located pin定位销
outer bush外导套
模板类
top plate上托板（顶板）
top block上垫脚
punch set上模座
punch pad上垫板
punch holder上夹板
stripper pad脱料背板
up stripper上脱料板
male die公模(凸模)
feature die公母模
female die母模(凹模)
upper plate上模板
lower plate下模板
die pad下垫板
die holder下夹板
die set下模座
bottom block下垫脚
bottom plate下托板(底板) stripping plate内外打(脱料板) outer stripper外脱料板
inner stripper内脱料板
lower stripper下脱料板
零件类
punch冲头
insert入块(嵌入件)
deburring punch压毛边冲子groove punch压线冲子stamped punch字模冲子
round punch圆冲子
special shape punch异形冲子
bending block折刀
roller滚轴
baffle plate挡块
located block定位块
supporting block for location
定位支承块
air cushion plate气垫板
air-cushion eject-rod气垫顶杆trimming punch切边冲子
stiffening rib punch = stinger 加强筋冲子ribbon punch压筋冲子
reel-stretch punch卷圆压平冲子
guide plate定位板
sliding block滑块
模具相关英语(4)
coordinate坐标
dismantle the die折模
auxiliary fuction辅助功能
poly-line多义线
heater band 加热片
thermocouple热电偶
sand blasting喷沙
grit 砂砾
derusting machine除锈机
degate打浇口
dryer烘干机
induction感应
induction light感应光
response=reaction=interaction感应
ram连杆
edge finder巡边器
concave 凹
convex凸
short射料不足
nick缺口
speck瑕疪
shine亮班
splay 银纹
gas mark焦痕
delamination起鳞
cold slug冷块
blush 导色gouge沟槽;凿槽
satin texture段面咬花
? 2010-3-15 11:08
? 回复
?
? khalidl
?
7楼
witness line证示线
patent专利
grit沙砾
granule=peuet=grain细粒
grit maker抽粒机
cushion缓冲
magnalium镁铝合金magnesium镁金
metal plate钣金
lathe车
mill锉
plane刨
grind磨
drill钻
boring镗
blinster气泡
fillet镶;嵌边
through-hole form通孔形式voller pin formality滚针形式cam driver铡楔
shank摸柄
crank shaft曲柄轴
augular offset角度偏差
velocity速度
production tempo生产进度现状torque扭矩
spline=the multiple keys花键quenching淬火
tempering回火
annealing退火
carbonization碳化
alloy合金
tungsten high speed steel钨高速的moly high speed steel钼高速的organic solvent有机溶剂
bracket小磁导
liaison联络单
volatile挥发性
resistance电阻
ion离子
titrator滴定仪
beacon警示灯
coolant冷却液
crusher破碎机
模具工程类
plain die简易模
pierce die冲孔模
forming die成型模
progressive die连续模
gang dies复合模
shearing die剪边模
riveting die铆合模
pierce冲孔
forming成型(抽凸,冲凸)
draw hole抽孔
bending折弯
trim切边
emboss凸点
dome凸圆
模具相关英语(3)
difference quantity差异量
cause analysis原因分析
raw materials原料
materials物料
finished product成品
semi-finished product半成品
packing materials包材
good product/accepted goods/ accepted parts/good parts良品
defective product/non-good parts不良品disposed goods处理品
warehouse/hub仓库
on way location在途仓
oversea location海外仓
spare parts physical inventory list备品盘点清单
spare molds location模具备品仓
skid/pallet栈板tox machine自铆机
wire EDM线割
EDM放电机
coil stock卷料
sheet stock片料
tolerance工差
score=groove压线
cam block滑块
pilot导正筒
trim剪外边
pierce剪内边
drag form压锻差
pocket for the punch head挂钩槽slug hole废料孔
feature die公母模
expansion dwg展开图
radius半径
shim(wedge)楔子
torch-flame cut火焰切割
set screw止付螺丝
form block折刀
stop pin定位销
round pierce punch=die button圆冲子shape punch=die insert异形子
stock locater block定位块
under cut=scrap chopper清角
active plate活动板
baffle plate挡块
cover plate盖板
male die公模
female die母模
groove punch压线冲子
air-cushion eject-rod气垫顶杆spring-box eject-plate弹簧箱顶板bushing block衬套
insert 入块
club car高尔夫球车
capability能力
parameter参数
factor系数
phosphate皮膜化成
viscosity涂料粘度
alkalidipping脱脂
main manifold主集流脉
bezel斜视规
blanking穿落模
dejecting顶固模
demagnetization去磁;消磁
high-speed transmission高速传递
heat dissipation热传
rack上料
degrease脱脂
rinse水洗
alkaline etch龄咬
desmut剥黑膜
D.I. rinse纯水次
Chromate铬酸处理
Anodize阳性处理
seal封孔
revision版次
part number/P/N料号
good products良品
scraped products报放心品
defective products不良品
finished products成品
disposed products处理品
barcode条形码
flow chart流程窗体
assembly组装
stamping冲压
molding成型
spare parts=buffer备品
模具相关英语(2)
material for engineering mold testing工程试模材料
not included in physical inventory不列入盘点
sample样品
incoming material to be inspected进货待验description品名
steel/rolled steel钢材
material statistics sheet
物料统计明细表
meeting minutes会议记录
meeting type 会别
distribution department分发单位location地点
chairman主席
present members出席人员
subject主题
conclusion结论
decision items决议事项
responsible department负责单位
pre-fixed finishing date预定完成日approved by / checked by / prepared by核准/审核/承办
PCE assembly production schedule sheet PCE组装厂生产排配表
model机钟
work order工令
revision版次
remark备注
production control confirmation生产确认checked by初审
approved by核准
department部门
stock age analysis sheet
库存货龄分析表
on-hand inventory现有库存
available material良品可使用
obsolete material良品已呆滞
to be inspected or reworked
待验或重工
total合计
cause description原因说明
part number/ P/N 料号
type形态
item/group/class类别
quality品质
prepared by制表
notes说明
year-end physical inventory difference analysis sheet
年终盘点差异分析表
physical inventory盘点数量
physical count quantity帐面数量
模具相关英语(1)
padding block垫块
stepping bar垫条
upper die base上模座
lower die base下模座
upper supporting blank上承板
upper padding plate blank上垫板
spare dies模具备品
spring 弹簧
bolt螺栓
document folder活页夹
file folder资料夹
to put file in order整理资料
spare tools location手工备品仓
first count初盘人
first check初盘复棹人
second count 复盘人
second check复盘复核人
equipment设备
waste materials废料
work in progress product在制品
casing = containerazation装箱
quantity of physical invetory second count 复盘点数量
quantity of customs count
会计师盘,点数量
the first page第一联
filed by accounting department for reference 会计部存查
end-user/using unit(department)使用单位summary of year-end physical inventory bills 年终盘点截止单据汇总表
bill name单据名称
This sheet and physical inventory list will be sent to accounting department together (Those of NHK will be sent to financial department) 本表请与盘点清册一起送会计部－(NHK厂区送财会部)
Application status records of year-end physical inventory List and physical inventory card 年终盘点卡与清册使用－状况明细表blank and waste sheet NO.
空白与作废单号
plate电镀
mold成型
注塑模部分中英文对照塑料成形模具mould for plastics
热塑性塑料模mould for thermoplastics 热固性塑料模mould for thermosets
压缩模compression mould
压注模、传递模transfer mould
注射模injection mould
热塑性塑料注射模injection mould for thermoplastics
热固性塑料注射模injection mould for thermoses
成形零件
定模stationary mould fixed half
动模movable mould moving half
定模座板fixed clamp plate, top clamping plate. top plate
动模座板moving clamp plate. bottom clamping plate. bottom plate
上模座板upper clamping plate
下模座板lower clamping plate
凹模固定板cavity-retainer plate
型芯固定板core-retainer plate
凸模固定板punch-retainer plate
模套chase. bolster. frame
支承板backing plate. supprr plate
垫块spacer parallel
支架ejector housing. mould base leg
序号中文英语日语港台俗称
3.1.2 动模movable mould moving half
3.2.1 定模座板fixed clamp plate, top clamping plate. top plate
3.2.2 动模座板moving clamp plate. bottom clamping plate. bottom plate 3.2.3 上模座板upper clamping plate
3.2.4 下模座板lower clamping plate
3.2.5 凹模固定板cavity-retainer plate
3.2.6 型芯固定板core-retainer plate
3.2.7 凸模固定板punch-retainer plate
3.2.8 模套chase. bolster. frame 3.2.9 支承板backing plate. supprr plate
3.2.10 垫块spacer parallel
3.2.11 支架ejector housing. mould base leg
中文查英文：英语查中文
根据国家标准，以下为部分压铸模具术语的标准翻译。
序号中文英语日语港台俗称
2 压力铸造模具die-casting die
3 压铸模零部件
3.1 定模fixed die, cover die
3.2 定模座板fixed clamping plate 3.1.3 定模套板bolstor, fixed die 3.2 动模moving die,ejector die 3.2.2 动模座板moving clamping plate
3.1 直流道sprue
3.1.1 横流道runner
3.1.2 内浇口gate
Surface Appearance
外观
Glossiness/gloss finish
光洁度
Matt finish/matt surface
毛面
Glass fiber rich surface/glass emergence on the surface
玻纤外露
Blooming/surface blooming
表面析出
White patches on surface
表面白斑
Silver marks/silver streak
银纹
Splay mark
水纹
Flow mark
流纹Weld line
溶结纹
Brittle/brittleness
脆
Bubbles/trapped gas
气泡
V oid
孔
Burn marks
烧伤
FR failed
阻燃不合格
Flame rating V-2
阻燃V-2
Poor dispersion
分散不好
FR/PTFE …agglomerates etc 阻燃剂/PTFE…结块
Pellet porous
粒子不密/蜜蜂窝
Low impact/tensile etc
物理性能低
High flow/filler content etc 流动性/填充…过高
Longs/fines/doubles
长粒/碎屑/连粒
Poor cut
粒形不好
Bristle/voids
表面有小气泡/孔
Glass bundles
玻纤结团
Product was rejected due to 产品不能接受因为…
High moisture level
高水分
Warpage/warped
翘曲
Shrinkage/shrink
收缩
Sink marks
缩影
Short shot/short molding
打不满
Distortion
变形
Over dimension
Final cushion minimum value 不知道这个是在哪个页面或项目下，如果是射胶那应该是：最小射胶终点（应该是品质项目设置的）Change-over to holding by value不知道这个是在哪个页面或项目下，如果是射胶那应该是：最大射胶终点（应该是品质项目设置的）Plasticizing end value终点位置
设计专业英语
方案：Design, Scheme 初步设计：Primary Design 施工图CD: Construction Design Fuction 功能区 Light 灯具 Droplight 吊灯 吸顶灯 Entrance 入口 Living room 客厅 Sitting room 起居室 Embed light 嵌灯 Dinning room 餐厅 Daylight lamp 日光灯 Kitchen 厨房 Reflect down light 筒灯 Office 书房 Quartz down-light 石英灯Master bedroom 主卧房Votage track light 射灯 Quest bedroom 客卧 Track light 轨道灯 Children bedroom 儿童房Picture light 镜画灯 Hiding light 暗藏灯管Projection room 视听室
Dressing room 更衣室Wall lamp 壁灯Storeroom 储藏室Reading lamp 台灯Master bathroom 主卫Floor lamp 落地灯Bathroom 卫生间Bathroom fixture 卫生洁具Wash room 洗衣房Staircase 楼梯Washbowl 洗手台[台盆] Aisle 过道 Water faucet 水龙头Closestool 座便器Gazebe 阳台 Urinal 小便斗 Garden 花园 Bathtab 浴缸 Swimming pool 游泳池Shower bath 淋浴房Furniture 家具 Wiring 电器设备Cupboard 厨房橱柜Television 电视机
最新新闻传播专业英语专业词汇整理大全
传播学英语专业词汇传播Communication 内向/自我传播Intrapersonal Communication 人际传播Interpersonal Communication 群体传播Group Communication 组织传播Organization Communication 大众传播Mass Communication 单向传播One-Sided Communication 双向传播Two-Sided Communication 互动传播Interactive Communication 媒介Media 大众传播媒介Mass Media 新媒介New Media 新闻洞News Hold 新闻价值News Value 传播者Communicator 主动传播者Active Communicator 受传者/受众/阅听大众Audience 受众兴趣Audience Interest 受众行为Audience Activity 信息Information
信号Signal 讯息Message 信息熵Entropy 冗余/冗余信息Redundancy 传播单位Communication Unit 奥斯古德模式Osgood Model 编码Encode 解码Decode 信源Source 传播的数学理论Mathematical Theory of Communication 传播渠道Communication Channel 有效传播Effective Communication 传播效果Effects 知识沟Knowledge-Gap 使用与满足模式Uses and Gratifications Model 使用与依从模式Uses and Dependencys Model 口传系统System of Oral Communication 地球村Global Village 内爆Implosion 全球化Globalization 本土化Localization
材料专业英语常见词汇
材料专业英语常见词汇（一） Structure ['str?kt??]组织 Ceramic [si'r?mik]陶瓷 Ductility [d?k'til?ti] 塑性 Stiffness ['stifnis]刚度 Grain [ɡrein]晶粒 Phase [feiz]相 Unit cell 单胞 Bravais lattice 布拉菲['l?tis]布拉菲点阵 Stack [st?k]堆垛 Crystal ['krist?l] 晶体 Metallic crystal structure [mi't?lik, me-]金属性晶体点阵Non-directional [,n?ndi'rek??n?l, -dai-]无方向性 Face-centered cubic ['kju:bik]面心立方 Body-centered cubic 体心立方Hexagonal close-packed [hek's?ɡ?n?l]['kl?us'p?kt]密排六方Copper ['k?p?] 铜 Aluminum [?'lju:min?m]铝 Chromium ['kr?umj?m]铬 Tungsten ['t??st?n]钨 Crystallographic Plane [,krist?l?u'ɡr?fik][plein]晶面Crystallographic direction 晶向 Property ['pr?p?ti] 性质 Miller indices ['indisi:z]米勒指数 Lattice parameters ['l?tis][p?'r?mit?]点阵参数 Tetragonal [te'tr?ɡ?n?l]四方的 Hexagonal [hek's?ɡ?n?l]六方的 Orthorhombic [,?:θ?'r?mbik]正交的Rhombohedra [,r?mb?u'hi:dr?] 菱方的 Monoclinic [,m?n?u'klinik]单斜的 Prism ['prizm]棱镜 Cadmium ['k?dmi?m]镉 Coordinate system [k?u'?:dinit, k?u'?:dineit]坐标系Point defect ['di:fekt, di'f-, di'fekt]点缺陷Lattice ['l?tis]点阵 Vacancy ['veik?nsi]空位 Solidification [,s?lidifi'kei??n]结晶 Interstitial [,int?'sti??l]间隙 Substitution [,s?bsti'tju:??n]置换 Solid solution strengthening [s?'lju:??n]['stre?θ?n, 'stre?kθ?n] 固溶强化
传播学专业英语词汇表
传播学专业英语词汇表第一部分：基本传播学理论词汇 传播Communication 内向/自我传播Intrapersonal Communication 人际传播Interpersonal Communication 群体传播Group Communication 组织传播Organization Communication 大众传播Mass Communication 单向传播One-Sided Communication 双向传播Two-Sided Communication 互动传播Interactive Communication 媒介Media 大众传播媒介Mass Media 新媒介New Media 新闻洞News Hold 新闻价值News Value 传播者Communicator 主动传播者Active Communicator 受传者/受众/阅听大众Audience 受众兴坤Audience Interest 受众行为Audience Activity 信息Information
信号Signal 讯息Message 信息熵Entropy 冗余/冗余信息Redundancy 传播单位Communication Unit 奥斯古德模式Osgood Model 编码Encoding 解码Decoding 信源Source 传播的数学理论Mathematical Theory of Communication 传播渠道Communication Channel 有效传播Effective Communication 传播效果Effects 知识沟Knowledge-Gap 使用与满足模式Uses and Gratifications Model 使用与依从模式Uses and Dependencys Model 口传系统System of Oral Communication 地球村Global Village 内爆Implosion 全球化Globalization 本土化Localization 电子空间Cyber Space 数字化Digitalization
常用专业英语词汇集锦.
六. Abbreviation
168 169 170 171 172 173 174 175 176 177 178 179 180 181 182 183 184 185 186 187 188 189 190 191 192 193 194 195 196 197 198 199 200 201 202 203 204 R/D R/I RCCP REV RMA RMA ROP RPN RTV S/N S/O SAI SCM SFC SIP SIS SMD SMT SOP SOR SPC SPEC SQM SWOT TE TOC TPI TPM TQA TQC TQM VQA VQM W/H W/O WHS WIP Research and Development Run-In Rough Cut Capacity Planning Revision Returned Merchandise Access Return Merchandise Approval(or Authorization Re-Order Point Risk Priority Number Return To Vendor Serial Number Sales Order Social Accountability International Supply Chain Management Shop Floor Control Standard Inspection Procedule Strategic Information System Surface Mounting Device Surface Mounting Technology Standard Operation Procedure Special Order Request Statistical Process Control Specification Supplier Quality Management Strengths、Weaknesses、Opportunities、 Threates test engineering Theory of Constraints Total Productive Innovation Total Production Management Total Quality Assurance Total Quality Control Total Quality Management Vender Quality Approval Vendor Quality Management Warehouse Work Order warehouse Work In Process 研發部常溫熱機(老
注塑机常用英语
注塑英语大全 成型工艺流程及条件介绍Molding technique procedure and parameter introduction 第一节成型工艺Section 1 molding technique.
1.成型工艺参数类型Sorts of molding parameter. (1).注塑参数ction parameter. a.注射量ction rate. b.计量行程Screw back position c.余料量Cushion d.防诞量Sucking back rate e.螺杆转速Screw speed f.塑化量Plastic0 rate g.预塑背压Screw back pressure h.注射压力和保压压力ction pressure and holding pressure i.注射速度ction speed (2)合模参数Clamping parameter a.合模力Clamping force b.合模速度Clamping speed c.合模行程.Clamping stroke d.开模力Opening force e .开模速度Opening speed f. 开模行程Opening position g.顶出压力Ejector advance pressure h.顶出速度Ejector advance speed i.顶出行程Ejector advance position 2.温控参数Temperature parameter a.烘料温度Dry resin material temperature b.料向与喷嘴温度Cylinder temperature and nozzle temperature c.模具温度Mold temperature d.油温Oil temperature 3.成型周期Molding cycle a.循环周期Cycle time b.冷却时间Cool time c.注射时间ction time d.保压时间Holding pressure time e.塑化时间Plant tim f.顶出及停留时间Knocking out and delay time g.低压保护时间Mold protect time 成型工艺参数的设定须根据产品的不同设置. Molding technique parameter setting differs depending on type of product 第二节成型条件设定Section 2 Molding parameter Setting 按成型步骤:可分为开锁模,加热,射出,顶出四个过程.Molding steps: mold opening/closing, heating ction and knocking out. 开锁模条件: Mold opening parameter: 快速段中速度High-speedmid-speed 低压高压速度Low pressure high pressure speed 锁模条件设定: Mold closing parameter setting 1锁模一般分:快速→中速→低压→高压 Mold closing: high-speed →low-speed →low pressure→high pressure
(完整版)土木工程专业英语常用词汇
Part IV：Commonly Used Professional Terms of Civil Engineering development organization 建设单位 design organization 设计单位 construction organization 施工单位 reinforced concrete 钢筋混凝土 pile 桩 steel structure 钢结构 aluminium alloy 铝合金 masonry 砌体（工程）reinforced ~ 配筋砌体load-bearing ~ 承重砌体unreinforced ~非配筋砌体 permissible stress (allowable stress) 容许应力plywood 胶合板 retaining wall 挡土墙 finish 装修 finishing material装修材料 ventilation 通风 natural ~ 自然通风 mechanical ~ 机械通风 diaphragm wall (continuous concrete wall) 地下连续墙 villa 别墅 moment of inertia 惯性矩 torque 扭矩 stress 应力normal ~ 法向应力shear ~ 剪应力 strain 应变 age hardening 时效硬化 air-conditioning system空调系统 (air) void ration（土）空隙比 albery壁厨，壁龛 a l mery壁厨，贮藏室 anchorage length锚固长度 antiseismic joint 防震缝 architectural appearance 建筑外观 architectural area 建筑面积 architectural design 建筑设计 fiashing 泛水 workability (placeability) 和易性 safety glass安全玻璃 tempered glass (reinforced glass) 钢化玻璃foamed glass泡沫玻璃 asphalt沥青 felt (malthoid) 油毡 riveted connection 铆接 welding焊接 screwed connection 螺栓连接 oakum 麻刀，麻丝 tee三通管 tap存水弯 esthetics美学 formwork 模板（工程） shoring 支撑 batching 配料 slipform construction (slipforming) 滑模施工 lfit-slab construction 升板法施工 mass concrete 大体积混凝土 terrazzo水磨石 construction joint 施工缝 honeycomb蜂窝，空洞，麻面 piled foundation桩基 deep foundation 深基础 shallow foundation浅基础 foundation depth基础埋深 pad foundation独立基础 strip foundation 条形基础 raft foundation筏基 box foundation箱形基础 BSMT=basement 地下室 lift 电梯electric elevator lift well电梯井 escalator 自动扶梯 Poisson’s ratio 泊松比μ Young’s modulus , modulus of elasticity 杨氏模量，弹性模量E safety coefficient 安全系数 fatigue failure 疲劳破坏 bearing capacity of foundations 地基承载力bearing capacity of a pile 单桩承载力 two-way-reinforcement 双向配筋 reinforced concrete two-way slabs钢筋混凝土双向板 single way slab单向板 window blind 窗帘sun blind wind load 风荷载 curing 养护 watertight concrete 防水混凝土 white cement白水泥 separating of concrete混凝土离折segregation of concrete mortar 砂浆~ joint 灰缝 pilaster 壁柱 fire rating耐火等级 fire brick 耐火砖 standard brick标准砖
英语专业四级词汇表(全)
pacific a.和平的n.太平洋pack vt.捆扎；挤满n.包package n.包裹，包，捆packet n.小包(裹)，小捆 pad n.垫；本子vt.填塞 page n.页 pail n.桶，提桶 pain n.痛，痛苦悲伤；辛劳painful a.使痛的；费力的paint vt.画；油漆vi.绘画painter n.漆工，画家，绘画者painting n.油画；绘画；着色pair n.一对vi.成对，配对palace n.宫，宫殿 pale a.苍白的；浅的 palm n.手掌，手心；掌状物pan n.平底锅，盘子 panda n.小猫熊；猫熊 pane n.窗格玻璃 panel n.专门小组；面，板pant n.气喘；心跳 paper n.纸；官方文件；文章
parade n.游行；检阅vi.游行paradise n.伊甸乐园；天堂paragraph n.(文章的)段，节parallel a.平行的；相同的parcel n.包裹，小包，邮包pardon n.原谅；赦免vt.原谅parent n.父亲，母亲，双亲 park n.公园；停车场 parliament n.议会，国会 part n.一部分；零件；本份partial a.部分的；不公平的partially ad.部分地 participate vi.参与，参加；分享particle n.粒子，微粒 particular a.特殊的；特定的particularly ad.特别，尤其，格外partly ad.部分地，不完全地partner n.伙伴；搭挡；配偶party n.党，党派；聚会 pass vt.经过；通过；度过passage n.通过；通路，通道passenger n.乘客，旅客，过路人
[电气工程]常用专业英语词汇
电气工程常用专业英语词汇表 电气工程常用专业英语词汇表 电路基础 ideal voltage (current) source 理想电压(流)源volt-ampere characteristic 伏安特性potential difference 电位差 reference potential 参考电位resistance 电阻capacitance 电容 inductance 电感 reactance 电抗 inductive(capacitive) reactance 感(容)抗impedance 阻抗 equivalent circuit 等效电路 Ohm’s law 欧姆定律Kirchhoff’s law 基尔霍夫定律Kirchhoff’s voltage law（KVL）基尔霍夫电压定律Kirchhoff’s current law（KCL）基尔霍夫电流定律Thevenin’s theorem 戴维宁定理Norton’s theorem 诺顿定理 branch 支路 node 结点 loop 回路 mesh 网孔 open circuit 开路（断路） short circuit 短路 branch current analysis 支路电流法mesh current analysis 网孔电流法 ode voltage analysis 结点电位法n superposition theorem 叠加原理passive(active) two-terminal network 无(有)源二端网络root mean square (RMS) 均方根值 effective value 有效值instantaneous value 瞬时值 ampere 安培 volt 伏特 Hertz 赫兹 reactive power` 无功功率 active power 有功功率 transfer function 传递函数 apparent power 视在功率 power-factor compensation 功率因数补偿series (parallel) resonance 串(并)联谐振 amplitude(phase)-frequency response characteristic 幅(相)频特性 figure of merit 品质因素 pass-band 通频带bandwidth (BW) 带宽 first(second)-order filter 一(二)阶滤波器low(high)-pass filter 低(高)通滤波器band-pass(stop) filter 带通(阻)滤波器transfer function 转移函数 Bode diagram 波特图 Fourier series 傅立叶级数 three-phase circuit 三相电路 cutoff frequency 截止频率 FFT (Fast Fourier Transform) 快速傅立叶变换 state variable 状态变量 电机 generation 发电 transmission 输电 distribution 配电 coil 线圈 core 铁心 winding 绕组 electrical machine 电机 generator 发电机 motor 电动机 stator (rotor) 定子(转子) armature 电枢 brush 电刷 commutator 换向器 salient-pole 凸极 slip ring 滑环 induction motor 感应电动机 magnetic flux 磁通 asynchronous machine 异步电机 synchronous generator 同步发电机 eddy current 涡流 EMF（electromotive force）电动势 counter EMF 反电势 torque 转矩 excitation 励磁 prime mover 原动机 rectifier 整流器 leakage flux 漏磁通 demagnetization 退磁，去磁 short-circuit ratio 短路比 converter (inverter) 换流器（逆变器） synchronous condenser 同步调相机 magnetization curve 磁化曲线 separately exciting 他励 compounded excited 复励 self-exciting 自励 series(shunt)-wound 串(并)励
设计常用英语词汇
Description: 方案：Design, Scheme 初步设计：Primary Design 施工图 CD: Construction Design Fuction 功能区 Light 灯具 Droplight 吊灯 吸顶灯 Entrance 入口 Living room 客厅 Sitting room 起居室 Embed light 嵌灯 Dinning room 餐厅 Daylight lamp 日光灯 Kitchen 厨房 Reflect down light 筒灯 Office 书房 Quartz down-light 石英灯Master bedroom 主卧房 Votage track light 射灯 Quest bedroom 客卧 Track light 轨道灯 Children bedroom 儿童房Picture light 镜画灯
Hiding light 暗藏灯管Projection room 视听室Dressing room 更衣室 Wall lamp 壁灯 Storeroom 储藏室 Reading lamp 台灯 Master bathroom 主卫Floor lamp 落地灯Bathroom 卫生间 Bathroom fixture 卫生洁具Wash room 洗衣房Staircase 楼梯 Washbowl 洗手台[台盆] Aisle 过道 Water faucet 水龙头Closestool 座便器 Gazebe 阳台 Urinal 小便斗 Garden 花园 Bathtab 浴缸 Swimming pool 游泳池Shower bath 淋浴房Furniture 家具 Wiring 电器设备
自动化专业英语词汇大全
自动化专业英语词汇大全 acceleration transducer加速度传感器base coordinate system基座坐标系 acceptance testing验收测试Bayes classifier贝叶斯分类器 accessibility可及性bearing alignment方位对准 accumulated error累积误差bellows pressure gauge波纹管压力表 AC-DC-AC frequency converter交 - 直 -交变频器benefit-cost analysis收益成本分析 AC (alternating current) electric drive交流电子传bilinear system双线性系统 动biocybernetics生物控制论 active attitude stabilization主动姿态稳定biological feedback system生物反馈系统 actuator驱动器，执行机构black box testing approach黑箱测试法 adaline 线性适应元blind search盲目搜索 adaptation layer适应层block diagonalization块对角化 adaptive telemeter system适应遥测系统Boltzman machine玻耳兹曼机 adjoint operator伴随算子bottom-up development自下而上开发 admissible error容许误差boundary value analysis边界值分析 aggregation matrix集结矩阵brainstorming method头脑风暴法 AHP (analytic hierarchy process)层次分析法breadth-first search广度优先搜索 amplifying element放大环节butterfly valve蝶阀 analog-digital conversion模数转换CAE (computer aided engineering)计算机辅助工annunciator信号器程 antenna pointing control天线指向控制CAM (computer aided manufacturing)计算机辅助anti-integral windup抗积分饱卷制造 aperiodic decomposition非周期分解Camflex valve偏心旋转阀 a posteriori estimate后验估计canonical state variable规范化状态变量approximate reasoning近似推理capacitive displacem ent transducer电容式位移传a priori estimate先验估计感器 articulated robot关节型机器人capsule pressure gauge膜盒压力表 assignment problem配置问题，分配问题CARD 计算机辅助研究开发 associative memory model联想记忆模型Cartesian robot直角坐标型机器人 associatron联想机cascade compensation串联补偿 asymptotic stability渐进稳定性catastrophe theory突变论 attained pose drift实际位姿漂移centrality集中性 attitude acquisition姿态捕获chained aggregation链式集结 AOCS (attritude and orbit control system)姿态轨chaos 混沌 道控制系统characteristic locus特征轨迹 attitude angular velocity姿态角速度chemical propulsion化学推进 attitude disturbance姿态扰动calrity 清晰性 attitude maneuver姿态机动classical information pattern经典信息模式attractor吸引子classifier分类器 augment ability可扩充性clinical control system临床控制系统 augmented system增广系统closed loop pole闭环极点 automatic manual station自动 - 手动操作器closed loop transfer function闭环传递函数automaton自动机cluster analysis聚类分析 autonomous system自治系统coarse-fine control粗 -精控制 backlash characteristics间隙特性cobweb model蛛网模型
气象常用专业英语词汇
主题词表 English Chinese 01. 大气 atmospheric science 大气科学 meteorology 气象学 atmosphere 大气 atmospheric impurity 大气杂质 atmospheric suspended matter 大气悬浮物 atmospheric composition 大气成分 atmospheric mass 大气质量 atmospheric density 大气密度 atmospheric subdivision 大气分层 homosphere 均质层 heterosphere 非均质层 standard [pressure] level 标准层 isothermal layer 等温层 lower atmosphere 低层大气 middle atmosphere 中层大气 upper atmosphere 高层大气 troposphere 对流层 tropopause 对流层顶 stratosphere 平流层 stratopause 平流层顶 mesosphere 中间层 mesopause 中间层顶 thermosphere 热层 exosphere 外[逸]层 ionosphere 电离层 magnetosphere 磁层 ozonosphere 臭氧层 free atmosphere 自由大气 planetary atmosphere 行星大气 standard atmosphere(reference atmosphere) 标准大气（参考大气） homogeneous atmosphere 均质大气 isothermal atmosphere 等温大气 polytropic atmosphere 多元大气 scale height 大气标高 meteorological element 气象要素 air temperature 气温 wet-bulb temperature 湿球温度 dry-bulb temperature 干球温度 atmospheric pressure 气压 standard atmosphere pressure 标准大气压 station pressure 本站气压 sea-level pressure 海平面气压 pressure gradient 气压梯度 barometric height formula 压高公式pressure gradient force 气压梯度力Coriolis force 科里奥利力 water vapor 水[蒸]汽 water vapor pressure 水汽压 humidity 湿度 relative humidity 相对湿度 absolute humidity 绝对湿度 specific humidity 比湿 mixing ratio 混合比 dew point [temperature] 露点(温度) depression of the dew point （温度）露点差super-saturated air 过饱和空气 saturation specific humidity 饱和比湿saturation vapor pressure 饱和水汽压saturation deficit 饱和差 cloud 云 low cloud 低云 middle cloud 中云 high cloud 高云 cloud amount 云量 cloud height 云高 cloud genera 云属 cloud etage 云族 cloud species 云种 cloud variety 云类 cloud form 云状 cirrus, Ci 卷云 cirrostratus, Cs 卷层云 cirrocumulus, Cc 卷积云 altocumulus, Ac 高积云 altostratus, As 高层云 cumulus, Cu 积云 cumulus humilis, Cu hum 淡积云 cumulus congestus, Cu con 浓积云cumulonimbus, Cb 积雨云 cumulus fractus, Cu fra 碎积云stratocumulus, Sc 层积云 stratus, St 层云 nimbostratus, Ns 雨层云 stratiform cloud 层状云 cumuliform cloud 积状云 cold cloud 冷云 warm cloud 暖云 ice cloud 冰云 wind 风 wind direction 风向 wind speed, wind velocity 风速 maximum wind speed 最大风速
专业英语注塑成型专业词汇
专业英语---注塑成型专业词汇 Injection machine 啤机 Shot size（weight）实际射胶量injection volume 理论射胶量min mold height 最小容模厚度 Max mold height 最大容模厚度Tie bar clearance 拉杆间距Die plate size 模板尺寸 Ejector stroke 顶出行程barrel 炮筒，机筒clamp force 锁模力 non-return valve 止回阀 shear 剪切opening 开模行程Injection pressure 射胶压力back pressure 背压 nozzle size 射咀尺寸Cycle time 循环周期down time 停机时间hopper 料筒Mold release 脱模剂lubrication 润滑work horse 主力，主要 设备 Reserve pressure/packing pressure保压mold trial 试模shot （一）啤Decompress 减压oven 烤炉，烘灶shrinkage rate 收缩率Residence time 滞留时间 injection speed 注射速度booster time 增压时间Compression ratio 压缩比 mold close time 合模时间 Resin 胶料 Plastification 塑化，增塑viscosity 粘性，粘度contamination 污染，杂 物 Thermoplastic 热塑性塑料thermosetting plastics 热固性塑料Booster time 增压时间 feed 喂料，填充purge 净化Flame retardant 阻燃degradation 降解， 软化 regrind 再粉碎Water absorption 吸水reinforce 增强，加固specific gravity 比重
道路勘测设计 专业英语常用词汇和短语
道路勘测设计专业英语词汇与短语表 第一章绪论 道路road 公路highway 城市道路city road；urban road 厂矿道路factories and mines road 林区道路forest road 乡村道路country road 车辆换算系数vehicle conversion factor 城间道路interurban road 城市出入口公路city approach highway 道路工程road engineering 丝绸之路the silk road 道路网road metwork 道路(网)密度density of road network 道路技术标准technical standard of road 设计车辆design vehicle 特种车辆special vehicle 计算行车速度(设计车速) design speed 道路建筑限界boundary line of road construction 道路用地范围right of way 净空clearance 等级道路classified road 辅道relief road 高速公路free way；motorway 部分控制进入partial control of access 等级公路classified highway 等外公路substandard highway
干线公路arterial highway 支线公路feeder highway 国家干线公路(国道) natilnal trunk highway 省干线公路(省道) provincial trunk highway 县公路(县道) county road 乡公路(乡道) township road (county road) 绕行公路bypass 公路自然区划clinatic zoning for highway (城市)快速路expressway (城市)主干路arterial road (城市)次干路secondary trunk road (城市)支路branch road 街道street 郊区道路suburban road 居住区道路residential street 工业区道路industial district road 厂外道路ractory-out road 厂内道路factory-in road (厂内)主干道arterial road (厂内)次干道secondary trunk road (厂内)支道branch road 露天矿山道路opencast mine road 生产干线prductive arterial road 生产支线productive branch road 联络线linking-up road 林区公路fores thighway 运材道路haul road 集材道路skid road 护林防火道路protection forest fire-proof road
常用专业术语英文
组装、冲压、喷漆等专业词汇 Assembly line组装线 Layout布置图 OOBA开箱检查 fit together组装在一起 fasten锁紧(螺丝) fixture 夹具(治具) pallet栈板 barcode条码 barcode scanner条码扫描器 fuse together熔合 repair修理 operator作业员 QC quality品管 supervisor 课长 section supervisor课长 deputy section supervisor =vice section superisor副课长 ME制造工程师 MT制造生技 cosmetic inspect外观检查 inner parts inspect内部检查 thumb screw大头螺丝 lbs. inch镑、英寸 front plate前板 rear plate后板 chassis基座 bezel panel面板 power button电源按键 reset button重置键Hi-pot test of SPS高源高压测试 V oltage switch of SPS 电源电压接拉键 sheet metal parts 冲件 plastic parts塑胶件 SOP制造作业程序 material check list物料检查表 trolley台车 carton纸箱 sub-line支线 left fork叉车 personnel resource department 人力资源部 production department生产部门 planning department企划部 QC Section品管科 stamping factory冲压厂 painting factory烤漆厂 molding factory成型厂 punching machine 冲床 robot机械手 lathe车床 planer |'plein|刨床 miller铣床 grinder磨床 driller??床 linear cutting线切割 electrical sparkle电火花 welder电焊机 staker=reviting machine铆合机 position职务 president董事长 general manager总经理 special assistant manager特助 factory director厂长 department director部长 deputy manager | =vice manager副理 group leader/supervisor组长 line supervisor线长 thickness gauge厚薄规 gauge(or jig)治具 power wire电源线 buzzle蜂鸣器 defective product label不良标签 identifying sheet list标示单 iudustrial alcohol工业酒精 Tiana天那水 packaging打包 missing part漏件 wrong part错件 excessive defects过多的缺陷 critical defect极严重缺陷 major defect主要缺陷 minor defect次要缺陷 not up to standard不合规格 dimension/size is a little bigger尺寸偏 大(小) cosmetic defect外观不良 slipped screwhead/slippery screw head 螺丝滑头 speckle斑点 rust生锈 deformation变形 burr(金属)flash(塑件)毛边 poor staking铆合不良 excesssive gap间隙过大 grease/oil stains油污 inclusion杂质 painting peel off脏污 shrinking/shrinkage缩水 mixed color杂色 scratch划伤 poor processing 制程不良 poor incoming part事件不良 painting make-up补漆 discoloration羿色 water spots水渍 polishing/surface processing表面处理 exposed metal/bare metal金属裸露 lack of painting烤漆不到位 safety安全 quality品质 delivery deadline交货期 cost成本 engineering工程 die repair模修 enterprise plan = enterprise expansion projects企划 qualified products, up-to-grade products良品 defective products, not up-to-grade products不良品 to return material/stock to退料 scraped |'skræpid|报废 (be)qualfied, up to grade合格 not up to grade, not qualified不合格