重复性和再现性分析报告
PLEASE SPECIFY THE FOLLOWING PARAMETERS AND COMPLETE THE FORM ACCORDINGLY PARAMETERS ARE
K1Number of Trials试验次数Must be either 2 or 3必须为2或32OK
K2Number of Operators操作人数Must be either 2 or 3必须为2或33OK
K3Number of Parts零件数Must be either 10必须为1010OK
'01 PSW'!H6'01 PSW'!A21'01 PSW'!A54'01 PSW'!H54GAGE APPROVED, USE IT Part number零件号4975198Part name零件名称信号盘Plant厂家#REF!
Characteristic特性位置度Gage number量具编号Coord by#REF!
Tolerance0.25Units Gage name量具名称三坐标Phone ##REF!
Tolerance (Tol)公差/60.0416667Gage ECL/revision Date日期
OPERATOR P A R T RESULTS
TRIAL #12345678910AVG A10.050.020.130.050.040.060.130.110.120.05A10.07500
20.050.010.130.050.040.070.130.110.120.04A20.07420
3A3
Average均值0.05350.01550.12950.0480.04250.06050.12850.10650.1180.0435X A0.07460 Range极差0.0010.0050.0030.0020.0010.0090.0070.0010.0020.003R A0.00340 B10.050.020.130.050.040.060.130.120.120.05B10.07710
20.050.020.130.040.040.060.140.120.120.04B20.07680
3B3
Average均值0.05250.01550.1320.0450.03950.05950.1340.12050.12350.0475X B0.07695 Range极差0.0010.0010.00.0040.0030.0050.0020.0030.0010.009R B0.00290 C10.050.010.130.050.050.060.130.110.130.05C10.07800
20.050.020.130.050.050.070.140.120.130.05C20.08030
3C3
Average均值0.050.01450.130.0470.0510.0650.1350.11550.1330.0505X C0.07915 Range极差0.0040.0030.0080.0020.0040.0060.0020.0070.0020.003R C0.00410 Part Avg0.0520.015170.13050.046670.044330.061670.13250.114170.124830.04717x PART =0.07690 Part Range R PART =0.11733
R =R A+ R B + R C / No. of operators =0.00340+0.00290+0.00410/3R =0.00347 X DIFF=[Max (X)ABC] - [Min (X)ABC] =0.07915-0.07460X DIFF =0.00455 UCL R=R*D4 =0.00347* 3.270UCL R =0.01134 LCL R=R*D3 =0.00347*0.000LCL R =0.00000 OPERATOR NAME NOTE: It has been statistically proven that the Tolerance Method is better
A chan to determine measurement equipment reliability. Even with negative
B lee Kurtosis data sets, the recorded measurements will be less than 1% away
C zhang from the true value if GR&R is below 30%. Contact Quality Group if you
GOOD UNTIL GAGE ECL/revision CHANGE need more information.
FROM DATA SHEET:R =0.00347X DIFF =0.00455R PART =0.11733
Measurement Unit Analysis测量数据分析Based on the TOLERANCE Method采用公差法Repeatibility - Equipment Variation (EV)重复性-设备变差
EV =R * K1% EV = 100[EV/Tol]
EV =0.00307Trials K1% EV =7.37
20.8862
Reproducibility - Appraiser Variation (AV)再现性-评价人变差
AV= [ ( X DIFF * K2)2 - (EV2 / nr)](n parts, r trials)% AV = 100[AV/Tol]
AV=0.00228Oper K2% AV = 5.47
30.5231
Repeatibility & Reproducibility (R & R)重复性和再现性% R&R = 100[R&R/Tol]
R&R= (EV2 + AV2)% R&R =9.18
R&R=0.00383
Part Variation (PV)零件变差% PV = 100[PV/Tol]
PV=R PART * K3Parts K3% PV =88.59
PV=0.03691100.3146ndc=(1.41PV/R&R)
Total Variation (TV)总变差0.3146ndc=13.606922
TV= (R&R2 + PV2)#REF!GAGE IS ACCEPTED
TV=0.03711
Part Certification
NON DESTRUCTIVE TEST 非破坏性试验
PLEASE SPECIFY THE FOLLOWING PARAMETERS AND COMPLETE THE FORM ACCORDINGLY PARAMETERS ARE
K 1Number of Trials 试验次数Must be either 2 or 3必须为2或32OK
K 2Number of Operators 操作人数Must be either 2 or 3必须为2或33OK K 3Number of Parts 零件数
Must be either 10必须为10
10
OK
'01 PSW'!H6'01 PSW'!A21'01 PSW'!A54'01 PSW'!H54
GAGE APPROVED, USE IT
Part number 零件号4975198Part name 零件名称信号盘Plant 厂家#REF!Characteristic 特性位置度Gage number 量具编号
Coord by #REF!Tolerance
0.25
Units
Gage name 量具名称三坐标Phone ##REF!
Tolerance (Tol)公差/60.0416667
Gage ECL/revision
Date 日期