焊接英语词汇
argon arc weld 氩弧焊
butt weld 对接焊（缝）
cluster weld 丛聚焊（缝）
cold weld 冷焊（缝），冷压接
fillet weld 角焊（缝）
flash butt weld 闪光对接焊（缝）
full fillet weld 满角焊（缝）
groove weld 坡口焊（缝）
mash seam weld 滚压焊
seam weld 滚焊（缝）
slot weld 切口焊（缝）
spot weld 点焊（缝）
tack (positioned) weld 定位【点位】焊（组焊前）weldability 可焊性，焊接性
welder 焊工；焊机
welding 焊接（法），焊接（的），焊缝atomic hydrogen weld 原子氢焊
attachment weld 固定焊接
bead weld 堆焊，狭的焊接
braze weld 硬【钎】焊，铜焊
built-up weld 堆焊
down hand weld 俯【水平】焊接
electric arc weld 电弧焊
flat position weld （顶面）平【卧】焊
flow weld 铸（浇）焊
forehand weld 正手焊（法）
forge weld 锻焊，锻接
friction weld 摩擦焊
gas shield weld 气体保护弧焊
inert-gas metal-arc weld 焊丝惰性气体保护焊oxyacetylene weld 氧（乙炔）焊，气焊percussion weld 冲击焊
plasma-arc weld 等离子弧焊
repair weld 补焊
roll weld 滚压焊
scarf weld 斜面焊，两端搭接焊，嵌接焊shield weld 气体保护焊
union arc weld 磁性焊剂二氧化碳保护焊unionmelt weld 埋弧（焊剂层下）自动焊weldment 焊接件，焊接装配
bonding technology 焊接工艺
fillet weld 角焊,填角焊
seal welding. 密封焊接
ring joint 环接, 围缘接合
seal fitting 密封接头, 密封配件
weld reinforcement 焊缝补强
dimensional inspection 尺寸检验
flange gasket 法兰垫片
burn through 烧蚀
girth weld 环形焊缝reinforcement of weld 加强焊缝
weld joint 焊缝, 焊接接头circumferential joint 周圈接缝
butt weld 对接焊缝
arc welding 电弧焊
filler rod 焊条
shield gas 保护气体
welding rod 焊条
welding bead 焊道，熔敷焊道，焊珠electrode 电焊条
longitudinal. 纵向的
horizontal line 水平线
welded joint 焊接缝焊接节点
witness test 订货人在场的试验Alignment：对准,定位调整
gas cutting. 气割
arc cutting 电弧切割
grind off 磨掉
Leveling：校平
Fixing：固定
Console：控制台
material certificate 材料合格证
fabrication 加工,制造
post weld heat treatment 焊后热处理
flushing 冲洗，填缝
arc gouging 电弧刨削
machining 机械加工
nut 螺母
solvent 溶剂
tack welding 点焊
butt welding 对接焊
reinforcing pad.补强垫,增强衬板
flux 焊剂
blind 挡板
gusset plate 角撑板, 加固板
base material 基底材料
flow sheet 流程图
witnessed inspections 现场检测
drain 排水管identification mark 识别标志
silicone paint 硅树脂油漆fabrication drawing 制造图纸,制作图
WPS Works Process Specification 典型工艺规程caulking metal 填隙合金[金属](材料) weld bead 焊缝
weld mark 焊痕
bonding wire 接合线, 焊线埋弧焊Submerged-arc Welding 电阻焊
Resistance Welding 滚焊
Seam welding throat thickness 焊缝厚度
摘自《英汉机械工程技术词汇》weldability 可焊性，焊接性Weldable steel 焊接钢
Weldability of metal 金属可焊性Weldability test 可焊性试验
Weld all around 围焊
Weldable copper 可焊复合铜板Weld assembly 焊接件
Weld bond 熔合线，焊口Weld cap 焊冒
Weld collar 加强焊缝焊瘤Weld crack 焊接裂缝
Weld crater 熔池
Weld crosswise 交叉焊接
Weld decay 焊缝腐蚀，焊接接头晶间Weld defect 焊接缺陷
Weld deposit 堆焊，焊缝熔敷
Welded all round 沿周边焊接的
Welded armor 焊接甲板
Welded body 焊接车身
Welded bridge 焊接桥
Welded bond 焊接轨隙连接器，焊接导接线Welded cathode 焊接阴极
Welded chain 焊接链
Welded connection 焊接合，焊接头Welded construction 焊接结构
Welded－contract rectifier 焊接整流器Welded corner joint 角焊接
Welded eye 焊眼
Welded fissure 焊接裂缝
Welded fitting 焊接式管接头
Welded flange 焊接翼缘
Welded frame 焊接车架，焊接框架
Welded frog 焊接辙差
Weld edgewise 沿边焊接
Welded metal 焊接金属
Welded pipe 焊接管
Welded module 焊接微型组件
Welded on head 焊制封头，焊制端盖Welded plate 焊合板
Welded seam 焊缝
Welded shell course 焊接锅炉筒
Welded shell ring焊接锅炉筒
Welded splice 焊接接头
Welded steel 焊接钢
Welded steel fabric 焊接钢筋网
Welded steel forging 熔焊钢锻件
Welded steel pipe 焊接钢管
Welded steel pipe pile 焊接钢管桩
Welded structural shape 焊接结构型钢Welded structural 焊接结构
Welded truss 焊接桁架
Welded tube 焊缝[接]管
Welded turret 焊合转塔
Welded wire fabric 焊接钢丝网
Welder 焊机，焊工
Welder construction 焊接结构
Welder performance qualification test 焊工技术鉴定试验Welder’s gauntlets 电焊工的长手套
Welder’s gloves 电焊工手套
Welder’s goggles 焊工护目镜
welder’s hand shield 焊工手持护目镜
Welder’s head shield 焊工护目帽罩
Welder’s health 焊工保健
Welder’s helmet 焊工帽罩
Welders spatter ease 焊接易飞溅液
Welder with condenser 带电容弧焊机
Welder with taps 抽头式焊机
Weld flaw 焊接缺陷，焊接裂纹
Weld flush 焊缝隆起
Weld flux 焊剂，焊药
Weldforged 锻焊
Weld gauge 焊缝量规
Weld handle 焊把
Weld holder 焊接架
Welding 焊接法，熔接，定位焊接；粘结
Welding agent 焊药
Welding alloy 焊接合金
Welding and cutting torch 焊割两用气焊枪
Welding－and－forming mill 成型焊管机
Welding apron 焊工的围裙
Welding arc 焊弧
Welding arc voltage 焊弧电压
Welding assembly 焊接构件
Welding base metal 焊条金属
Welding beading 焊瘤Welding
bead length 焊缝长度
Welding bell 碗模（焊管用的），拔管模，喇叭模Welding bench 焊接工作台
Welding blew lamp 焊炬
Welding blowpipe 气焊吹管
Welding booth 焊接室
Welding burner 焊炬喷嘴
Welding by both sides 双面焊
Welding by forging 锻焊
Welding by one side 单面焊
Welding cable 电焊电缆，电焊引线
Welding characteristics 焊接特性
Welding compound 焊【接】剂
Welding conditions 焊接规范
Welding connector 电缆夹头
Welding contactor 电焊接触器
Welding control 接触焊机断流器
Welding crack 焊裂缝
Welding current 焊接电流
Welding cut bit 焊接工具
Welding deformations 焊接变形
Welding direction 焊接方向
Welding dynamo 焊接发电机
Welding electrode 电焊条，电焊电极
Welding electrode hold 焊条夹
Welding equipment 焊接设备
Welding fixture 焊接夹具
Welding flame 焊接火焰
Welding flash 弧光灼伤
Welding fluid 熔【焊】剂
Welding flux 焊剂，焊药
Welding force 阻焊加压；电极压力
Welding from both sides 双面焊
Welding from one side 单面焊
Welding furnace 烧结炉
Welding gauge 确定焊缝尺寸用样板
Welding gang 焊工班，焊接组
Welding generator电焊发动机
Welding generator with differential excitation 差激电焊发动机
Welding generator with split－Poles 裂极电焊发动机Welding glass 黑玻璃
Welding gloves焊接手套
Welding goggles 焊工护目镜
Welding grade argon 焊接极氩，焊接用氩
Welding grade gas 焊接级保护气体
Welding ground 电焊地线
Welding gun 焊枪，喷灯
Welding gutter 焊管拉模
Welding handle 焊条夹，电极夹钳
Welding head 焊头，烙铁头，焊接机头
Welding heat 焊热
Welding heat input 焊接输入热量
Welding helmet 焊工帽罩
Welding holder 焊工握把
Welding impulse 电焊脉冲
Welding inspection 焊接检查
Welding iron 烙铁
Welding jig 焊接夹具
Welding joint 焊接接头
Welding lead 焊接引线
Welding machine 焊机
Welding manipulator 焊件支架
Welding metal cracking 焊缝金属裂纹Welding method 焊接方法
Welding motor generator 电动旋转式电焊机
Welding neck （flange）对焊法兰
Welding－on 焊合，镶焊，焊上
Welding operation 焊接操作
Welding operator 自动焊工
Welding outfit 焊接配备
Welding paste 焊接涂料
Welding performance 焊接性能
Welding pipe 焊接管
Welding pistol 焊枪
Welding point 焊接接头
Welding pool 焊接熔池
Welding portion 焊接部位，施焊部位
Welding position 焊接部位
Welding positioner 焊接胎架，可动焊接工作台Welding positioner roller 焊接定位滚轮
Welding powder 焊粉
Welding power lead 焊接用输电线
Welding press 焊接压力机
Welding pressure 焊接压力
Welding procedure 焊接工艺，焊接程序
Welding process 焊接法
Welding quality 焊接质量
Welding rectifier 电焊整流器
Welding regulator 焊接[电流]调节器
Welding research council 焊接研究委员会
Welding residual stress 焊接残余应力
Welding resistor 焊接电阻器
Welding rod 焊条
Welding rod coating 焊条上的焊药
Welding rod core 焊条芯
Welding rod extrusion press 焊条自动涂抹机，焊条压涂机
Welding rolls 焊条辊
Welding rules 焊接规则
Welding screen 电焊遮光罩
Welding seam 焊缝
Welding sequence 焊接程序
Welding set 焊接装置，电焊机组
Welding set with a surge injector 脉冲稳弧焊接装置Welding set with DC suppression capacitors 电容抑制直流成分的焊接设备
Welding set with H.F. ionizer 带高频电离的焊接装置Welding shop 焊接车间
Welding slag 焊渣
Welding sleeves [焊接用]套轴
Welding socket 焊接管套（管接头）
Welding source 焊接电源
Welding spats 焊接用护脚
Welding spatter 焊渣
Welding steel 焊接钢
Welding stick 焊丝，焊条
Welding strain 焊接应变
Welding stress 焊接应力
Welding symbol 焊接符号，焊接代号Welding table 焊接工作台
Welding temperature 焊接温度
Welding thermit [铝]热剂（焊接用）welding tip 焊嘴，焊接吹管火口Welding tongs 焊钳
Welding tool 焊接工具
Welding torch 焊接喷灯，焊接吹管，焊炬Welding torch pipe 焊枪管
Welding transformer 电焊变压器Welding tub 焊接熔池
Welding wheel 盘状电极
Welding wire 焊条，焊丝
Welding－wire reel 焊丝卷圈
Welding with backing 垫板焊
Welding with flux backing 焊剂垫焊Welding with pressure 压焊
Welding with weaving 横向摆动焊接Welding work 焊工工作
Welding－in nozzle 焊入式喷嘴
Welding interface 焊接界面
Weld jig 焊接夹具
Weld joint 焊缝，焊接接头
Weld junction 熔合线，焊口
Welding layer 焊接层
Weld length 焊缝长度
Weldless 无焊缝的，无缝的
Weldless connection 非焊接式接头Weldless drawn pipe 拉制无缝管Weldless fitting 非焊接式接头
Weldless pipe 无缝管
Weldless steel tube 无[焊]缝
钢管Weld line 焊接线
Weld machined flush 削平补强的焊缝Weld mark 焊接痕，焊波
Weldment 焊接件，焊接装配
Weld mesh crate 焊接网格
Weld metal 焊接金属，焊缝金属
Weld metal cracking 焊缝裂纹
Weld metal zone 焊接金属熔化区
Weld on bottom 底焊
Weldor 焊工
Weld pass 焊接通道
Weld penetration 焊穿，焊透深度，熔深Weld period 焊接时间Weld preparation 焊缝坡口加工
Weld puddle 熔池
Weld reinforcement 焊缝补强
Weld ripple 焊缝波纹
Weld rod 焊条
Weld rotation 焊缝转角
Weld seam 焊缝
Weld slope 焊缝倾角
Weld strain 焊接应变
Weld strength 焊接强度，焊缝强度
Weld surface 焊缝表面
Weld time [接触焊的]通电时间
Weld trimmer 焊缝清理机
Weld up 焊补，焊封
Weld wire 包钢铜丝
Weldwood 胶合板
Weld zone 焊接区
Lack of fusion 未熔合
Sharp edge 锐边
Serrated edge 锯齿形边
Torch cut 火焰切割
Sawn 锯
Air tight 气密性
机械类常用英语：焊接用语acetylene 乙炔
ampere 电流安培
angle welding 角焊
arc 电弧
argon arc welding 氩弧焊接
bare electrode 光熔接条
butt welding 对接焊接
camber 电弧弯曲
cascade 阶叠熔接法
clad weld 被覆熔接
crator 焊疤
excess metal 多余金属
filler rod 焊条
fillet weld 填角焊接
gas shield 气体遮蔽
groove welding 起槽熔接
hand face shield 手握面罩
hard facing 硬表面堆焊
jig welding 工模焊接
laser beam welding 雷射光焊接
metal electrode insert gas welding MIG熔接nugget 点焊熔核
overlaying 堆焊
peening of welding 珠击熔接法
plug welding 塞孔熔接
常用焊接英语词汇大全
常用焊接英语词汇大全 焊接机器人welding robot 点焊机器人spot welding robot 弧焊机器人arc welding robot 切割机器人cutting robot 焊接机器人生产线robot line for welding 焊接机器人工作站welding robot station 机器人运动自由degree of free for robot 机器人工作空间robot working space 波峰钎焊flow soldering/ wave soldering 分级钎焊step brazing/ step soldering 不等间隙钎焊brazing with the unparalleled clearance 红外线钎焊infra-red brazing (soldering) 光束钎焊light soldering (brazing) 激光钎焊laser brazing (soldering) 电子束钎焊electron beam brazing 钎接焊braze-welding 钎料brazing filler metal/ solder 硬钎料brazing filler metal 软钎料solder (m) 自钎剂钎料self-fluxing brazing alloy/ self-fluxing filler metal 活性钎料active filler metal/ active metal brazing alloy 成形钎料preformed filler metal/ solder preform 非晶态钎料amorphous filler metal 粉状钎料powdered filler metal 钎料膏braze cream/ braze paste/ solder cream/ solder paste 药皮钎料flux coated brazing(soldering)rod 层状钎料sandwich filler metal 药芯钎料丝flux-cored colder wire 敷钎料板clad brazing sheet 钎剂brazing flux; soldering flux 气体钎剂gas flux 反应钎剂reaction flux 松香钎剂colophony flux; rosin flux 钎剂膏flux paste 阻流剂stopping-off agent 钎剂活性flux activity 钎剂活性温度范围activation temperature range of flux 钎剂热稳定性thermal stability of flux 钎焊过程brazing (soldering) process 钎焊操作brazing (soldering) operation
焊接专业术语中英文对照整理
机械——焊接专业术语中英文对照 （郭运）整理 1Single 单面的 2V—groove V型坡口 3Joint 焊接接头 4Edges overlap 接头形式 5Butt 对接 6T T型焊接 7Fillet 角焊缝 8Edge 端接 9Corner 角接 10Radius 半径 11Joint root 焊接根部 12Bevel angle 削边角度 13Groove angle 坡口角度 14Root face 根部钝边 15Groove face 坡口面 16Plug weld 塞焊 17Spot weld 点焊 18Seam weld 缝焊 19Slot weld 槽焊 20Double—flare—bevel—groove K型坡口焊缝
21Single—flare—V 单面V型22Edge flange 翻边端接 23Corner flange 卷边端接 24Flange weld 卷边焊缝25Flare weld 扩口焊缝26Fillet weld 角焊缝 27Slot weld 槽焊缝 28Spot weld 点焊缝 29Surfacing weld 堆焊焊缝30Melt—through weld 熔透焊缝31Backing weld 打底焊缝32Back weld 背面焊缝33Root weld 根部焊缝34Crown weld 隆起部分35Weld reinforcement 焊缝加强36Weld face 焊缝表面37Cap pass 盖面焊道38Weld edge 焊缝边缘39Leg 焊脚 40Toe 焊趾 41Buildup 堆焊 42Weld reinforcement 焊缝加强高
焊接专用英文词汇
焊接专用英文词汇 1.1 焊接方法 焊接方法与设备（Welding process& facility） 手工电弧焊(MAW:manual arc welding) 电弧焊（arc welding）埋弧电弧焊（SAW：submerged arc welding）气焊（gas welding）氩弧焊（argon arc welding） 气体保护电弧焊 CO2保护焊(CO2 shielded arc welding) 熔化焊（GMAW—gas metal arc welding） fusion welding 电渣焊(ESW—electroslag welding) 激光焊(LW—laster welding) 等离子焊(PAW—plasma arc welding) 摩擦焊（FRW—friction welding） 焊接压力焊超声波焊（UW—ultrasonic welding） welding pressure welding 冷压焊（CPW—cold pressure welding）锻焊（FW—forge-welding）对焊butt welding 电阻焊(RW—resistance welding) 缝焊seam welding 点焊spot welding 烙铁钎焊 iron soldering 火焰钎焊 torch brazing/ torch soldering 钎焊炉中钎焊 furnace brazing/ furnace soldering soldering/brazing 盐浴钎焊 saltbath dip brazing (soldering) 真空钎焊 vacuum brazing 堆焊 overlaying welding 平焊 downhand welding/flat welding 横焊 horizontal welding 立焊 vertical welding 仰焊 overhead welding 全位置焊 all position welding/positional welding 半自动电弧焊 Semi-automatic arc welding 钨极惰性气体保护电弧焊 (TIG) tungsten inert-gas arc welding 熔化极惰性气体保护电弧焊（MIG）metal inert-gas arc welding 1.2 焊接设备 电弧焊机 arc welding machine 直流弧焊机 DC arc welding machine 交流弧焊机 AC arc welding machine 交直流两用弧焊机 AC/DC arc welding machine 氩弧焊机 argon arc welding machine 二氧化碳弧焊机 CO2 arc welding machine 埋弧焊机 submerged arc welding machine 焊接机头 welding head 行走机构 traveller 送丝机构 wire feeder 焊丝盘 wire reel
焊接英文词汇--有用
焊接英文词汇 BPS---钎接工艺规程 PQR---钎接工艺评定纪录 SWPS---标准焊接工艺规程 WPS---welding procedure specification焊接工艺规程 Hard conversion---近似转换 Soft conversion---精确转换 ASNT---American Society of Nondestructive Testing 美国无损检测学会Arc seam weld---点弧焊焊缝 Arc spot weld---点弧焊点 Arc welding---弧焊 As-brazed---钎接焊 As-welded---焊态 Back gouging---背面清根 Backhand welding---右焊法 Backing---衬垫 Backing gas---背面保护气 Base metal---母材 Bond line—熔合线 Braze---钎接接头 Brazer---钎接工 Brazing, automatic---自动钎接 Brazing, block (BB)---加热块钎接 Brazing, dip (DB)---浸沾钎接 Brazing, furnace (FB)---炉中钎接 Brazing, induction (IB)---感应钎接 Brazing, machine---机动钎接 Brazing, manual---手工钎接 Brazing, resistance (RB)---电阻钎接 Brazing, semiautomatic---半自动钎接 Brazing, torch (TB) ---火焰钎接 Brazing, temperature range---钎接温度范围 Built-up of base metal---母材补焊 Butt joint---对接接头 Buttering---堆焊隔离层 Clad brazing sheet---敷钎料板 Coalescence---接合 Complete fusion---完全熔合 Composite---复合材料 Consumable insert---可熔化嵌条 Contact tube---导电咀 Corner joint---角接接头 Coupon---试件 Crack---裂纹
常用焊接术语中英文对照
常用焊接术语中英文对照 焊接Welding 10.1 焊接种类Varieties of Welding 电弧焊arc welding 电熔焊electric fusion welding (EFW) 气熔焊fusion gas welding (FGW) 电阻焊electric resistance welding (ERW) 有保护的金属电弧焊shielded metal arc welding (SMAW) 手工或自动隋性气体保护钨极电弧焊manual and automatic inert gas tungsten arc welding (GTAW) 自动埋弧焊automatic submerged arc welding 金属极隋性气体保护电弧焊gas metal arc weiding (GMAW) 氩弧焊argon-arc welding， 气体保护电弧焊gas-shielded arc welding 气焊gas welding; flame welding 等离子焊plasma welding 硬钎焊braze welding 电渣焊electroslag welding 爆炸焊explosive welding 10.2 焊接形式Type of Welding
角焊fillet welding 间断焊intermittent welding 点焊spot welding 对焊butt welding 搭焊lap welding 塞焊plug welding 珠焊bead welding 槽焊slot welding 堆焊build up welding 垫板焊backing weld 坡口groove V形坡口V groove 单面U形坡口single U groove K形坡口double bevel groove X形坡口double V groove 双面U形坡口double U groove U-V组合坡口combination U and V groove 根部间隙root gap 焊接符号symbol of weld 错边量alignment tolerance 10.3 焊接位置Welding Position 仰焊overhead welding 现场焊field weld (F.W.)
焊接专业英语词汇(通用部分)
焊接专业英语词汇（通用部分） acetylene 乙炔am pere 电流安培 angle welding 角焊arc 电弧 argon arc welding 氩弧焊接bare electrode 光熔接条 butt welding 对接焊接cam ber 电弧弯曲 cascade 阶叠熔接法clad weld 被覆熔接 crator 焊疤excess m etal 多余金属 filler rod 焊条fillet weld 填角焊接 gas shield 气体遮蔽groove welding 起槽熔接 hand face shield 手握面罩hard facing 硬表面堆焊 jig welding 工模焊接laser beam welding 雷射光焊接 metal electrode insert gas welding MIG熔接nugget 点焊熔核overlaying 堆焊peening of welding 珠击熔接法 plug welding 塞孔熔接positioned welding 正向熔接 pressure welding 压焊propane gas cutting 丙烷气切割 pure nickel electrode 纯镍熔接条reinforcem ent of weld 加强焊接resist 抗蚀护膜root running 背面熔接 seam焊缝seaming 接合 seam welding 流缝熔接series seam welding 串联缝熔接 skip welding process 跳焊法spark 火花 spot welding 点焊接stitch welding 针角焊接 stud arc welding 电弧焊接under laying 下部焊层 void 焊接空隙weld flow m ark 焊接流痕 weld flush 焊缝凸起weld line 焊接纹 weld m ark 焊接痕weld penetration 熔接透入 weld zone 焊接区welding 焊接 welding bead 焊接泡welding direction 焊接方向 welding distortion 焊接变形welding flux 焊剂 welding ground 电熔接地welding interval 焊接周期 welding stress 熔接应变welding torch 熔接气炬 welding electrode production line 电焊条生产线 welding electrode 焊条 welding fixture 焊接夹具 welding generator 电焊机 welding goggles 焊工护目镜 welding gun 焊枪 welding helmet 电焊帽 welding inspection ruler 焊接检验尺 welding machine 焊接机 welding mill 焊管机 welding motor generator 电动焊接发电机 welding nozzle 焊嘴 welding paste 焊接药膏
焊接专业英语词汇(熔化焊)
2006-09-02 | 焊接专业英语词汇（熔化焊） 熔接fusion welding 压接pressure welding 焊接过程welding process 焊接技术welding technique 焊接工艺welding technology/procedure 焊接操作welding operation 焊接顺序welding sequence 焊接方向direction of welding 焊接位置welding position 熔敷顺序build-up sequence deposition sequence 焊缝倾角weld slope/inclination of weld axis 焊缝转角weld rotation/angle of rotation 平焊位置flat position of welding 横焊位置horizontal position of welding 立焊位置vertical position of welding 仰焊位置overhead position of welding 平焊downhand welding/flat position welding 横焊horizontal position welding 立焊vertical position welding 仰焊overhead position welding 全位置焊all position welding：熔焊时，焊件接逢所处空间位置包括平焊、横焊、仰焊等位置所进行的焊接。如水平固定管所进行的环缝焊接 向下立焊vertical down welding/downward welding in the vertical position 向上立焊vertical up welding/upward welding in the vertical position 倾斜焊inclined position welding 上坡焊upward welding in the inclined position 下坡焊downward welding in the inclined position 对接焊butt welding 角焊fillet welding 搭接焊lap welding 船形焊fillet welding in the downhand position/fillet welding in the flat position 平角焊horizontal fillet welding 立角焊fillet welding in the vertical position 仰角焊fillet welding in the overhead position 坡口焊groove welding I形坡口对接焊square butt welding 喇叭形坡口焊flare groove welding 卷边焊flanged edge welding 纵缝焊接welding of longitudinal seam 横缝焊接welding of transverse seam 环缝焊接girth welding/ circumferential
工程焊接英语(整理版)
术语和定义 A Alloy [?l?i] flux [fl?ks] 合金焊剂对焊缝金属合金成分起主要决定作用的焊剂。 all-weld-metal [metl] test specimen [spesim?n] 全焊缝金属试样完全由焊缝金属组成的缩减断面试样。 arc [ɑ:k] gouging [ɡaud?i?] 电弧刨槽用电弧切割方法形成斜面或坡口的热刨槽。 as-welded 焊后状态（焊态）焊后未经任何热处理、力学或化学处理的焊缝金属、焊接接头和焊件的状态。 automatic [?:t?m?tik] welding 自动焊接用设备进行的焊接，焊接中仅需偶然照看或根本无需照看，并且不需手工调节设备的控制。这一术语的变化形式有：自动硬钎焊，自动软钎焊，自动热切割和自动热喷涂。 auxiliary [?:ɡzilj?ri] attachments [?t?t?m?nt] 辅助附件用焊接办法附加于主要的承受应力部件上的部件或附件，这种部件可以或无需承受荷载。 axis [?ksis]of a weld. 焊缝轴线见weld axis。 B backgouging 清根从已焊接头焊缝根部一面清除焊缝金属和母材金属，以便于接着从该面施焊时完全熔合和接头完全熔透。backing 衬垫紧靠接头背面放置的、或者放置在电渣焊和气电焊焊缝两侧的材料或器件，用以承托和保持熔化的焊缝金属。焊接时，这种材料可以部分熔化或者不发生熔化，其材质既可以是金属，也可以是非金属。 backing pass 背部焊道背部焊缝的焊道。 backing ring 衬环环形衬垫，一般用于管材的焊接。 backing weld 打底焊缝焊缝形式的衬垫。 backup weld (tubular[tju:bjul?] structures[str?kt??]) 打底焊道（管结构）仅从一面施焊的接头完全熔透（CJP）坡口焊缝的初始封焊焊道。用作后续焊道的衬垫，但不视为理论焊缝的一部分。 back weld 背部焊缝施焊于单面坡口焊缝背部的焊缝。 base metal 母材被焊接、硬钎焊、软钎焊或切割的金属或合金。 bevel[bev?l] angle[??ɡl] 坡口面角度接头构件的坡口斜面与垂直于构件表面的平面之间的夹角。 box tubing[tju:bi?] 箱形管正方形或矩形横截面的管材产品。见Tubular。 brace intersection[int?sek??n] angle, θ(tubular structure) 支管交角θ（管结构）支管中心线之间形成的锐角。 building code 建筑规范本规范中用到建筑规范这一术语时，指的是本规范适用的建筑法律或规定，或其他的建造条例。当缺少任何当地适用的建筑法律或规定，或其他建造条例时，则建议建造应符合美国钢结构学会（AISC）的建筑用结构钢设计、制作和安装的技术条件。 butt joint
常用焊接中英文词语翻译
常用焊接中英文词语翻译焊接热源welding heat source 点热源point heat source 线热源linear heat source 面热源plane heat source 瞬时集中热源instantaneous concentration heat source 热效率thermal efficiency 热能集中系数coefficient of heat flow concentration 峰值温度peak temperature 瞬时冷却速度momentary cooling rate 冷却时间cooling time 置换氧化substitutionary oxydation 扩散氧化diffusible oxydation 脱氧desoxydation 先期脱氧precedent desoxydation 扩散脱氧diffusible desoxydation 沉淀脱氧precipitation desoxydation 扩散氢diffusible hydrogen 初始扩散氢initial diffusible hydrogen 100 C 残余扩散氢diffusible hydrogen remained at 100 °C 残余氢residual hydrogen 去氢dehydrogenation
去氢热处理heat treatment for dehydrogenation 脱硫desulphurization 脱磷dephosphorization 渗合金alloying 微量合金化microalloying 一次结晶组织primary solidification structure 二次结晶组织secondary solidification structure 联生结晶epitaxial solidification 焊缝结晶形态solidification mode in weld-bead 结晶层状线ripple 多边化边界polygonization boundary 结晶平均线速度mean solidification rate 针状铁素体acicular ferrite 条状铁素体lath ferrite 侧板条铁素体ferrite side-plate 晶界欣素体grain boundary ferrite; polygonal ferrite; pro-entectoid ferrite 粒状贝氏体granular bainite 板条马氏体lath martensite 过热组织overheated structure 魏氏组织Widmannst?tten structure M-A 组元martensite-austenite constituent 焊件失效分析failure analysis of weldments
焊接英语词汇
焊接的基本概念知识 ⑴熔化焊接（Fusion welding）手工电弧焊（SMAW：Shielded meta l arc weldi ng）埋弧焊（SAW：Submerged arc welding） 钨极惰性气体保护电弧焊（TIG：Tungsten Inert-Gas arc welding）⑵压力焊接（Pressure welding） 熔化极惰性气体保护电弧焊（MIG：meta l Inert-gas arc welding）爆炸焊（Expl osive welding） 冷压焊（Cold welding）摩擦焊（Friction welding）扩散焊（Diffusion weldin g）焊缝接头（Welded joint） ⑶钎焊（Soldering(软钎焊)/Brazing（硬钎焊））电阻钎焊（resistance brazing） 火焰钎焊（torch brazing/ soldering） 热压焊：hot pressure welding 电渣焊：electroslag welding薄钢板的焊接（We iling of thin steel sheets） 电子束焊：electron beam welding 电阻焊：resistance welding 点焊: Spot w eld 对接接头(Butt joint); 搭接接头（Lap joint）；角接接头（Fillet weld）T型接头（T-joint/Tee joint） 最常用的是:对接接头（Butt joint is the most used one）不开坡口的对接接头（Butt joint without groove） 两焊件端面相对平行的接头（The joint whose welding suefaces of both wel ding parts are parallel is called butt joint.） 如果产品在厚度方向上不要求全焊透，可进行单面焊接，应必须保证焊缝的计算厚度H≥0.7δ，δ为板厚。如果要求产品在整个厚度上全部焊透，可在焊缝背面用碳弧气刨清跟后再进行焊接，即形成不开坡口的双面焊接对接接头。（If the product doesn’t need full penetration of welding, we can take single-si de welding, and must make sure that the caculating thickness is more than or equal to 0.7δ(δis the thickness of steel sheets),If full penetration of weld ing needed, we can use carbon arcgouging to back chipping at the back of weld, after which weiding can be taken, than the double-faced welding butt joi nt without groove is formed.）
焊接专业英语词汇(通用部分)
焊接专业英语词汇（通用部分） Fierce welding 满焊焊烧 Symmetry welding 对称焊接 Welding deformation 焊接变形 Seal 封口 Vertical position welding 立焊 Horizontal position welding 横焊 Over-head position welding 仰焊 acetylene 乙炔ampere 电流安培 angle welding 角焊arc 电弧 argon arc welding 氩弧焊接bare electrode 光熔接条butt welding 对接焊接camber 电弧弯曲 cascade 阶叠熔接法clad weld 被覆熔接 crator 焊疤excess metal 多余金属 filler rod 焊条fillet weld 填角焊接 gas shield 气体遮蔽groove welding 起槽熔接 hand face shield 手握面罩hard facing 硬表面堆焊jig welding 工模焊接laser beam welding 雷射光焊接
metal electrode insert gas welding MIG熔接nugget 点焊熔核overlaying 堆焊peening of welding 珠击熔接法 plug welding 塞孔熔接positioned welding 正向熔接 pressure welding 压焊propane gas cutting 丙烷气切割 pure nickel electrode 纯镍熔接条reinforcement of weld 加强焊接resist 抗蚀护膜root running 背面熔接 seam 焊缝seaming 接合 seam welding 流缝熔接series seam welding 串联缝熔接 skip welding process 跳焊法spark 火花 spot welding 点焊接stitch welding 针角焊接 stud arc welding 电弧焊接under laying 下部焊层 void 焊接空隙weld flow mark 焊接流痕 weld flush 焊缝凸起weld line 焊接纹 weld mark 焊接痕weld penetration 熔接透入 weld zone 焊接区welding 焊接 welding bead 焊接泡welding direction 焊接方向 welding distortion 焊接变形welding flux 焊剂 welding ground 电熔接地welding interval 焊接周期 welding stress 熔接应变welding torch 熔接气炬 welding electrode production line 电焊条生产线 welding electrode 焊条 welding fixture 焊接夹具
焊接英语专业术语
焊接英语专业术语 1.1 焊接方法 焊接方法与设备（Welding process& f acility） 手工电弧焊(MAW:manual arc weldin g) 电弧焊（arc welding）埋弧电弧焊（S AW：submerged arc welding） 气焊（gas welding）氩弧焊（argon arc welding） 气体保护电弧焊 CO2保护焊(CO2 shie lded arc welding) 熔化焊（GMAW—gas metal arc weldi ng） fusion welding 电渣焊(ESW—electr oslag welding) 激光焊(LW—laster welding) 等离子焊(PAW—plasma arc welding) 摩擦焊（FRW—friction welding） 焊接压力焊超声波焊（UW—ultrason ic welding） welding pressure welding 冷压焊（C PW—cold pressure welding） 锻焊（FW—forge-welding）对焊but t welding 电阻焊(RW—resistance welding) 缝焊seam welding 点焊spot welding 烙铁钎焊 iron soldering 火焰钎焊 torch brazing/ torch sol dering 钎焊炉中钎焊 furnace brazing/ fu rnace soldering soldering/brazing 盐浴钎焊 saltba th dip brazing (soldering) 真空钎焊 vacuum brazing 堆焊 overlaying welding 平焊 downhand welding/flat weldin g 横焊 horizontal welding 立焊 vertical welding 仰焊 overhead welding 全位置焊 all position welding/pos itional welding 半自动电弧焊 Semi-automatic arc w elding 钨极惰性气体保护电弧焊 (TIG) tung sten inert-gas arc welding 熔化极惰性气体保护电弧焊（MIG）me tal inert-gas arc welding 1.2 焊接设备 电弧焊机 arc welding machine 直流弧焊机 DC arc welding machine 交流弧焊机 AC arc welding machine 交直流两用弧焊机 AC/DC arc weldin g machine 氩弧焊机 argon arc welding machin e 二氧化碳弧焊机 CO2 arc welding ma chine 埋弧焊机 submerged arc welding ma chine 焊接机头 welding head 行走机构 traveller 送丝机构 wire feeder 焊丝盘 wire reel 焊钳 electrode holder 焊枪 welding gun 碳弧气割 carbon arc air gouging 火焰气刨 flame gouging 焊接夹具 welding jig/ fixture 等离子弧焊机 plasma arc welding m achine 等速送丝方式 constant wire-feed s ystem 变速送丝方式 alternate wire-feed system 点焊机 spot welding machine 缝焊机 seam welding machine 对焊机 butt resistance welding ma chine 凸焊机 projection welding machine 2、焊接材料及焊接工艺（welding ma terials& procedure） 2.1 焊接材料 碳钢 carbon steel 合金钢 alloy steel 不锈钢 stainless steel 耐热钢 high-temprature steel 铸铁 casting 铜/黄铜 copper 青铜 bronze 铝 aluminium 镁 magnisium 钛 titanium 钨 tungsten 镍 nickel 铬 chromium 2.2 焊接工艺 焊接技能 welding technique 焊接方法 welding process 焊接工艺welding procedure 焊接操作 welding operation 焊接顺序 welding sequence 焊接方向 welding progress 焊缝宽度 weld width 焊缝厚度 weld throat 焊缝余高 weld reinforcement 焊缝长度 weld length 焊接参数 welding parameter 焊接电流 welding current 焊接速度 welding speed 焊接电压 welding voltage 焊接变形 welding deformation 根部间隙 root opening
焊接专业英语词汇(钎焊)
焊接专业英语词汇（钎焊） 钎焊 硬钎焊brazing 软钎焊soldering 烙铁钎焊iron soldering 火焰钎焊torch brazing/ torch soldering 热风钎焊hot gas soldering 感应钎焊induction brazing 电阻钎焊resistance brazing 接触反应钎焊contact-reaction brazing 电弧钎焊arc brazing 浸渍钎焊dip brazing/ dip soldering 盐浴钎焊saltbath dip brazing (soldering) 金属浴钎焊molten metal bath dip brazing 炉中钎焊furnace brazing/ furnace soldering 保护气氛钎焊brazing in controlled atmosphere 真空钎焊vacuum brazing 蒸气钎焊vapor phase soldering 超声波钎焊ultrasonic soldering 扩散钎焊diffusion brazing 波峰钎焊flow soldering/ wave soldering 分级钎焊step brazing/ step soldering
红外线钎焊infra-red brazing (soldering) 光束钎焊light soldering (brazing) 激光钎焊laser brazing (soldering) 电子束钎焊electron beam brazing 钎接焊braze-welding 钎料brazing filler metal/ solder 硬钎料brazing filler metal 软钎料solder (m) 自钎剂钎料self-fluxing brazing alloy/ self-fluxing filler met al 活性钎料active filler metal/ active metal brazing alloy 成形钎料preformed filler metal/ solder preform 非晶态钎料amorphous filler metal 粉状钎料powdered filler metal 钎料膏braze cream/ braze paste/ solder cream/ solder p aste 药皮钎料flux coated brazing(soldering)rod 层状钎料sandwich filler metal 药芯钎料丝flux-cored colder wire 敷钎料板clad brazing sheet 钎剂brazing flux; soldering flux 气体钎剂gas flux
常用焊接英语术语
常用焊接术语 在实际应用过程中，经常会碰到一些与焊接相关的术语，行话，总结如下： 正极性指直流焊接时，被焊物接（＋）极，焊条、焊丝接（－）极 反极性与正极性相反 直流电弧焊或电弧切割时，焊件与焊接电源输出端正、负极的接法称为极性。极性分正极性和反极性两种。焊件接电源输出端的正极，电极接电源输出端的负极的接法为正极性（常表示为DCSP）。反之，焊件接电源输出端的负极，电极接电源输出端的正极的接法为反极性（常表示为DCRP）。 欧美常常用另外一种表示方法，将DCSP称为DCEN，而将DCRP称为DCEP。 焊接电流为向焊接提供足够的热量而流过的电流 电弧电压指电弧部的电压，与电弧长大致成比例地增加，一般电压表所示电压值包括电弧电压及焊丝伸出部，焊接电缆部的电压下降值。 弧长弧部长度 弧坑在焊缝终点产生的凹坑 气孔熔敷金属里有气产生空洞 飞溅焊接时未形成熔融金属而飞出来的金属小颗粒 焊渣焊后覆盖在焊缝表面上的固态熔渣 熔渣包覆在熔融金属表面的玻璃质非金属物 咬边由于焊缝两端的母材过烧，致使熔融金属未能填满，形成槽状凹坑。 熔深母材熔化部的最深位与母材表面之间的距离 熔池因焊弧热而熔化成池状的母材部分 熔化速度单位时间里熔敷金属的重量 熔敷率有效附着在焊接部的金属重量占熔融焊条、焊丝重量的比例 未熔合对焊底部的熔深不良部，或第一层等里面未融合部 余高鼓出母材表面的部分或角焊末端连接线以上部分的熔敷金属 坡口角度母材边缘加工面的角度 预热为防止急热，焊接前先对母材预热（如火焰加热） 后热为防止急冷进行焊后加热（如火焰加热） 平焊从接头上面焊接
横焊从接头一侧开始焊接 立焊沿接头由上而下或由下而上焊接 仰焊从接头下面焊接 垫板为防止熔融金属落下，在焊接接头下面放上金属、石棉等支撑物。 夹渣夹渣是非金属固体物质残留于焊缝金属中的现象，夹杂物出现在熔焊过程中 焊剂焊接时，能够熔化形成熔渣和气体，对熔化金属起保护和冶金处理作用的一种物质。 碳弧气刨使用石磨棒或碳棒与工件间产生的电弧将金属熔化，并用压缩空气将其吹掉，实现在金属表面上加工沟槽的方法 保护气体焊接过程中用于保护金属熔滴、熔池及焊缝区的气体，它使高温金属免受外界气体的侵害 焊接夹具为保证焊件尺寸，提高装配精度和效率，防止焊接变形所采用的夹具 焊接工作台为焊接小型焊件而设置的工作台 焊接操作机将焊接机头或焊枪送到并保持在待焊位置，或以选定的焊接速度沿规定的轨迹移动焊剂的装置焊接变位机将焊件回转或倾斜，使接头处于水平或船行位置的装置 焊接滚轮架借助焊件与主动滚轮间的摩擦力来带动圆筒形（或圆锥形）焊件旋转的装置
常用焊接英语汇总
?热丝MIG焊hot wire MIG welding ?MIG熔接metal electrode insert gas welding ?X射线衍射法X-ray stress analysis ?X射线探伤X-ray radiographic inspection ?X射线工业电视探伤X-ray industrial television inspection ?Tigamajig 薄板焊接裂纹试验Tigamajing thin plate cracking test ?热丝TIG焊hot wire TIG welding ?100℃残余扩散氢diffusible hydrogen remained at 100℃ ?射频熔接; 高频焊接radio-frequency welding ?预热preheat ?预热preheat ?预热温度preheat temperature ?预热时间preheat time ?预热电流preheat current ?预热火焰preheat flame ?预热氧preheat oxygen ?CO2预热器CO2 heater ?预热Preheating ?预热温度Preheat temperature ?错边量unfitness of butt joint ?埋弧焊submerged arc welding (SAW) ?埋弧焊Submerged arc welding （SAW） ?自动埋弧焊automatic submerged arc welding ?窄间隙埋弧焊焊剂flux for narrow-gap submerged arc welding ?埋弧焊submerged arc welding (SAW) ?多丝埋弧焊multiple wire submerged arc welding ?纵列多丝埋弧焊Tandem sequence (submerged-arc welding) ?横列多丝埋弧焊series submerged arc welding (SAW-S) ?横列双丝并联埋弧焊transverse submerged arc welding ?热丝埋弧焊hot wire submerged-arc welding ?窄间隙埋弧焊narrow-gap submerged arc welding ?埋弧焊机submerged arc welding machine ?接合线, 焊线埋弧焊bonding wire ?埋弧焊Submerged arc welding （SAW） ?对接接头butt joint ?对接接头banjo fixing butt jointing ?对接接头butt joint ?I形对接接头square butt joint ?V形对接接头single V butt joint ?U形对接接头single U butt joint ?双V形对接接头double V butt joint ?双单边V形对接接头double bevel butt joint/ K groove butt joint ?带钝边U形对接接头double U butt joint ?锁底对接接头lock butt joint