6N136

Single Channel, High Speed Optocouplers Technical Data

Features

? 15 kV/μs Minimum Common Mode Transient Immunity at V CM = 1500 V (4503/0453)? High Speed: 1 Mb/s ? TTL Compatible

? Available in 8-Pin DIP, SO-8,Widebody Packages ? Open Collector Output ? Guaranteed Performance from Temperature: 0°C to 70°C

? Safety Approval

UL Recognized – 3750 V rms for 1 minute (5000 V rms for 1 minute for HCNW and Option 020 devices) per UL1577CSA Approved

IEC/EN/DIN EN 60747-5-2Approved

–V IORM = 630 V peak for HCPL-4503#060

–V IORM = 1414 V peak for HCNW devices

? Dual Channel Version

Available (253X/4534/053X/0534)

? MIL-PRF-38534 Hermetic Version Available (55XX/65XX/4N55)

Applications

? High Voltage Insulation ? Video Signal Isolation

? Power Transistor Isolation in Motor Drives ? Line Receivers

? Feedback Element in Switched Mode Power Supplies

? High Speed Logic Ground Isolation – TTL/TTL, TTL/CMOS, TTL/LSTTL

? Replaces Pulse Transformers ? Replaces Slow

Phototransistor Isolators ? Analog Signal Ground Isolation

Description

These diode-transistor optocoup-lers use an insulating layer

between a LED and an integrated photodetector to provide elec-trical insulation between input and output. Separate connections for the photodiode bias and output-transistor collector increase the speed up to a

hundred times that of a conven-tional phototransistor coupler by reducing the base-collector capacitance.

Functional Diagram

6N135/6HCNW135/6HCNW4502/3HCPL-2502HCPL-0452/3HCPL-0500/1HCPL-4502/3

CAUTION: It is advised that normal static precautions be taken in handling and assembly of this component to prevent damage and/or degradation which may be induced by ESD.

A 0.1 μF bypass capacitor must be connected between pins 5 and 8.

V CC V B V O GND

** NOTE: FOR 4502/3, 0452/3,

PIN 7 IS NOT CONNECTED.

TRUTH TABLE (POSITIVE LOGIC)

LED

ON

OFF

V O LOW HIGH

GND

V CC

O

ANODE

CATHODE

B

* NOTE: FOR HCPL-4502/-3, HCPL-0452/3, HCNW4502/3, PIN 7 IS NOT CONNECTED.

Ordering Information

Specify Part Number followed by Option Number (if desired).Example:

HCPL-4503#XXXX

020 =UL 5000 V rms/1 Minute Option*

060 =IEC/EN/DIN EN 60747-5-2 V IORM = 630 V peak Option**300 =Gull Wing Surface Mount Option?500 =Tape and Reel Packaging Option XXXE = Lead Free Option

Option data sheets available. Contact your Agilent sales representative or authorized distributor for information.

*For 6N135/6 and HCPL-4502/3 only.

**For HCPL-4503 only. Combination of Option 020 and Option 060 is not available.?Gull wing surface mount option applies to through hole parts only.

*Technical data for these products are on separate Agilent publications.?Pin 7, transistor base, is not connected.

output current for 1 TTL load and a 5.6 k ? pull-up resistor. CTR for these devices is 19% minimum at I F =16mA.

The HCPL-4502, HCPL-0452,and HCNW4502 provide the electrical and switching performance of the 6N136,

HCPL-0501, and HCNW136 with increased ESD protection.The HCPL-4503, HCPL-0453,and HCNW4503 are similar to the HCPL-4502, HCPL-0452, and HCNW4502 optocouplers but have increased common mode transient immunity of 15 kV/μs minimum at V CM =1500V guaranteed.

These single channel optocoup-lers are available in 8-Pin DIP,SO-8 and Widebody package configurations.

The 6N135, HCPL-0500, and HCNW135 are for use in TTL/CMOS, TTL/LSTTL or wide bandwidth analog applications.Current transfer ratio (CTR) for these devices is 7% minimum at I F =16mA.

The 6N136, HCPL-2502,

HCPL-0501, and HCNW136 are designed for high speed TTL/TTL applications. A standard 16 mA TTL sink current through the input LED will provide enough

Remarks: The notation “#” is used for existing products, while (new) products launched since 15th July 2001 and lead free option will use “-”

Package Outline Drawings

8-Pin DIP Package (6N135/6, HCPL-4502/3, HCPL-2502)

8-Pin DIP Package with Gull Wing Surface Mount Option 300 (6N135/6, HCPL-4502/3)

0.254+ 0.076- 0.051

(0.010+ 0.003)- 0.002)

DIMENSIONS IN MILLIMETERS AND (INCHES).*MARKING CODE LETTER FOR OPTION NUMBERS "L" = OPTION 020"V" = OPTION 060

OPTION NUMBERS 300 AND 500 NOT MARKED.

NOTE: FLOATING LEAD PROTRUSION IS 0.25 mm (10 mils) MAX.

(0.025 ± 0.005)(0.100)

BSC

DIMENSIONS IN MILLIMETERS (INCHES).

LEAD COPLANARITY = 0.10 mm (0.004 INCHES).

NOTE: FLOATING LEAD PROTRUSION IS 0.25 mm (10 mils) MAX.

+ 0.076- 0.051

+ 0.003)- 0.002)

Small Outline SO-8 Package (HCPL-0500/1, HCPL-0452/3)

8-Pin Widebody DIP Package (HCNW135/6, HCNW4502/3)

(0.012)

MIN.5.207 ± 0.254 (0.205 ± 0.010)

DIMENSIONS IN MILLIMETERS (INCHES).

LEAD COPLANARITY = 0.10 mm (0.004 INCHES) MAX.

*

1.78 ± 0.15NOTE: FLOATING LEAD PROTRUSION IS 0.25 mm (10 mils) MAX.

0.254+ 0.076- 0.0051+ 0.003)- 0.002)

8-Pin Widebody DIP Package with Gull Wing Surface Mount Option 300 (HCNW135/6,HCNW4502/3)

Solder Reflow Temperature Profile

TIME (SECONDS)

T E M P E R A T U R E (°C )

ROOM

1.78 ± 0.15MAX.BSC

DIMENSIONS IN MILLIMETERS (INCHES).LEAD COPLANARITY = 0.10 mm (0.004 INCHES).

NOTE: FLOATING LEAD PROTRUSION IS 0.25 mm (10 mils) MAX.

Regulatory Information

The devices contained in this data sheet have been approved by the following organizations:

UL

Recognized under UL 1577,Component Recognition Program, File E55361.

CSA

Approved under CSA Component Acceptance Notice #5, File CA 88324.

Insulation and Safety Related Specifications

8-Pin DIP Widebody (300 Mil)SO-8(400 Mil)Parameter Symbol Value Value Value Units Conditions

Minimum External L(101)7.1

4.9

9.6mm

Measured from input terminals Air Gap (External to output terminals, shortest Clearance)

distance through air.

Minimum External L(102)7.4 4.810.0mm

Measured from input terminals Tracking (External to output terminals, shortest Creepage)

distance path along body.Minimum Internal 0.080.08 1.0mm

Through insulation distance,Plastic Gap

conductor to conductor, usually (Internal Clearance)

the direct distance between the photoemitter and photodetector inside the optocoupler cavity.Minimum Internal NA NA 4.0mm

Measured from input terminals Tracking (Internal to output terminals, along Creepage)

internal cavity.

Tracking Resistance CTI 200200200Volts

DIN IEC 112/VDE 0303 Part 1

(Comparative Tracking Index)Isolation Group

IIIa IIIa IIIa

Material Group

(DIN VDE 0110, 1/89, Table 1)

Option 300 - surface mount classification is Class A in accordance with CECC 00802.

IEC/EN/DIN EN 60747-5-2Approved under

IEC 60747-5-2:1997 + A1:2002EN 60747-5-2:2001 + A1:2002DIN EN 60747-5-2 (VDE 0884 Teil 2):2003-01

(HCNW and Option 060 only)

Recommended Pb-Free IR Profile

°C of ACTUAL NOTES:

THE TIME FROM 25 °C to PEAK TEMPERATURE = 8 MINUTES MAX.T smax = 200 °C, T smin = 150 °C

IEC/EN/DIN EN 60747-5-2 Insulation Related Characteristics

(HCPL-4503 OPTION 060 ONLY)

IEC/EN/DIN EN 60747-5-2 Insulation Related Characteristics (HCNW135/6, HCNW4502/3 ONLY)

*Refer to the front of the optocoupler section of the current catalog, under Product Safety Regulations section IEC/EN/DIN EN

60747-5-2, for a detailed description.

Note: Isolation characteristics are guaranteed only within the safety maximum ratings which must be ensured by protective circuits in application.

*Data has been registered with JEDEC for the 6N135/6N136.

Electrical Specifications (DC)

Over recommended temperature (T A = 0°C to 70°C) unless otherwise specified. See note 13.

Parameter Symbol Device Min.Typ.**Max.Units Test Conditions Fig.Note Current CTR*6N13571850%T A = 25°C V O = 0.4 V I F = 16 mA,1, 2,5, 11 Transfer Ratio HCPL-0500V CC = 4.5 V4

HCNW135519V O = 0.5 V

HCPL-25021522T A = 25°C V O = 0.4 V

1525V O = 0.5 V

6N136192450T A = 25°C V O = 0.4 V

HCPL-4502/3

HCPL-05011525V O = 0.5 V

HCPL-0452/3

HCNW136

HCNW4502/3

Logic Low V OL6N1350.10.4V T A = 25°C I O = 1.1 mA I F = 16 mA,

Output Voltage HCPL-0500V CC = 4.5 V

HCNW1350.10.5I O = 0.8 mA

6N1360.10.4T A = 25°C I O = 3.0 mA

HCPL-2502

HCPL-4502/30.10.5I O = 2.4 mA

HCPL-0501

HCPL-0452/3

HCNW136

HCNW4502/3

Logic High I OH*0.0030.5μA T A = 25°C V O = V CC = 5.5 V I F = 0 mA7

Output Current0.011T A = 25°C V O = V CC = 15 V

50V O = V CC = 15 V

Logic Low I CCL50200μA I F = 16 mA, V O = Open, V CC = 15 V13 Supply Current

Logic High I CCH*0.021μA T A = 25°C I F = 16 mA, V O = Open,13 Supply Current2V CC = 15 V

Input Forward V F*8-Pin DIP 1.5 1.7V T A = 25°C I F = 16 mA3

Voltage SO-8 1.8

Widebody 1.45 1.68 1.85T A = 25°C I F = 16 mA

1.35 1.95

Input Reverse BV R*8-Pin DIP5V I R = 10 μA

Breakdown SO-8

Voltage Widebody3I R = 100 μA

Temperature?V F/8-Pin DIP-1.6mV/°C I F = 16 mA

Coefficient of?T A SO-8

Forward Voltage Widebody-1.9

Input C IN8-Pin DIP60pF f = 1 MHz, V F = 0 V

Capacitance SO-8

Widebody90

Transistor DC h FE8-Pin DIP150V O = 5 V, I O = 3 mA

Current Gain SO-8130V O = 0.4 V, I B = 20 μA

Widebody180V O = 5 V, I O = 3 mA

160V O = 0.4 V, I B = 20 μA

*For JEDEC registered parts.

**All typicals at T A = 25°C.

Parameter Sym.Device Min.Typ.**Max.Units Test Conditions

Fig.

Note Propagation t PHL *

6N1350.2 1.5μs T A = 25°C R L = 4.1 k ?

5, 6,8, 9

HCPL-0500 2.011

HCNW1356N1360.20.8T A = 25°C R L = 1.9 k ?

HCPL-2502HCPL-4502/3HCPL-0501HCPL-0452/3 1.0HCNW136HCNW4502/3

Propagation t PLH *

6N135 1.3 1.5μs

T A = 25°C R L = 4.1 k ?

5, 6,8, 9

HCPL-0500 2.011

HCNW1356N1360.60.8T A = 25°C R L = 1.9 k ?

HCPL-2502HCPL-4502/3HCPL-0501HCPL-0452/3 1.0HCNW136HCNW4502/3

Common Mode |CM H |

6N1351kV/μs R L = 4.1 k ?I F = 0 mA, T A = 25°C,

12

7, 8,HCPL-0500V CM = 10 V p-p 9

HCNW135C L = 15 pF

6N1361R L = 1.9 k ?

HCPL-2502HCPL-4502HCPL-0501HCPL-0452HCNW4502HCPL-45031530R L = 1.9 k ?I F = 0 mA, T A = 25°C,

HCPL-0453V CM = 1500 V p-p ,HCNW4503C L = 15 pF

Common Mode |CM L |

6N1351kV/μs R L = 4.1 k ?I F = 16 mA, T A = 25°C,

12

7, 8,HCPL-0500V CM = 10 V p-p 9

HCNW135C L = 15 pF

6N1361R L = 1.9 k ?

HCPL-2502HCPL-4502HCPL-0501HCPL-0452HCNW4502HCPL-45031530R L = 1.9 k ?I F = 16 mA, T A = 25°C,

HCPL-0453V CM = 1500 V p-p ,HCNW4503

C L = 15 pF

Bandwidth BW 6N135/69

MHz

See Test Circuit

8, 1010

HCPL-2502HCPL-0500/1HCNW135/611

*For JEDEC registered parts.**All typicals at T A = 25°C.

Switching Specifications (AC)

Over recommended temperature (T A = 0°C to 70°C), V CC = 5 V, I F = 16 mA unless otherwise specified.

Delay Time to Logic Low at Output

Delay Time to Logic High at Output

Transient Immunity at Logic High Level Output

Transient Immunity at Logic Low Level Output

Package Characteristics

Over recommended temperature (T A = 0°C to 70°C) unless otherwise specified.

*All typicals at T A = 25°C.

**The Input-Output Momentary Withstand Voltage is a dielectric voltage rating that should not be interpreted as an input-output continuous voltage rating. For the continuous voltage rating refer to the IEC/EN/DIN EN 60747-5-2 Insulation Related Characteristics Table (if applicable), your equipment level safety specification or Agilent Application Note 1074 entitled “Optocoupler Input-Output Endurance Voltage,” publication number 5963-2203E.

Notes:

1.Derate linearly above 70°C free-air temperature at a rate of 0.8 mA/°C (8-Pin DIP).

Derate linearly above 85°C free-air temperature at a rate of 0.5 mA/°C (SO-8).

2.Derate linearly above 70°C free-air temperature at a rate of 1.6 mA/°C (8-Pin DIP).

Derate linearly above 85°C free-air temperature at a rate of 1.0 mA/°C (SO-8).

3.Derate linearly above 70°C free-air temperature at a rate of 0.9 mW/°C (8-Pin DIP).

Derate linearly above 85°C free-air temperature at a rate of 1.1 mW/°C (SO-8).

4.Derate linearly above 70°C free-air temperature at a rate of 2.0 mW/°C (8-Pin DIP).

Derate linearly above 85°C free-air temperature at a rate of 2.3 mW/°C (SO-8).

5.CURRENT TRANSFER RATIO in percent is defined as the ratio of output collector current, I O, to the forward LED input current, I F,

times 100.

6.Device considered a two-terminal device: Pins 1, 2, 3, and 4 shorted together and Pins 5, 6, 7, and 8 shorted together.

https://www.360docs.net/doc/0e7351835.html,mon mode transient immunity in a Logic High level is the maximum tolerable (positive) dV CM/dt on the leading edge of the

common mode pulse signal, V CM, to assure that the output will remain in a Logic High state (i.e., V O > 2.0 V). Common mode transient immunity in a Logic Low level is the maximum tolerable (negative) dV CM/dt on the trailing edge of the common mode pulse signal, V CM, to assure that the output will remain in a Logic Low state (i.e., V O < 0.8 V).

8.The 1.9 k? load represents 1 TTL unit load of 1.6 mA and the 5.6 k? pull-up resistor.

9.The 4.1 k? load represents 1 LSTTL unit load of 0.36 mA and 6.1 k? pull-up resistor.

10.The frequency at which the ac output voltage is 3 dB below its mid-frequency value.

11.The JEDEC registration for the 6N136 specifies a minimum CTR of 15%. Agilent guarantees a minimum CTR of 19%.

12.See Option 020 data sheet for more information.

https://www.360docs.net/doc/0e7351835.html,e of a 0.1 μf bypass capacitor connected between pins 5 and 8 is recommended.

14.In accordance with UL 1577, each optocoupler is proof tested by applying an insulation test voltage ≥ 4500 V rms for 1 second

(leakage detection current limit, I I-O≤ 5 μA). This test is performed before the 100% Production test shown in the IEC/EN/DIN EN 60747-5-2 Insulation Related Characteristics Table if applicable.

15.In accordance with UL 1577, each optocoupler is proof tested by applying an insulation test voltage ≥ 6000 V rms for 1 second

(leakage detection current limit, I I-O≤ 5 μA). This test is performed before the 100% Production test shown in the IEC/EN/DIN EN 60747-5-2 Insulation Related Characteristics Table if applicable.

16.This rating is equally validated by an equivalent ac proof test.

Figure 2. Current Transfer Ratio vs. Input Current.

Figure 3. Input Current vs. Forward Voltage.

Figure 1. DC and Pulsed Transfer Characteristics.

105

V O – OUTPUT VOLTAGE – V

I O – O U T P U T C U R R E N T – m A

8 PIN DIP, SO-8

12

8

V O – OUTPUT VOLTAGE – V

I O – O U T P U T C U R R E N T – m A

4

16

WIDEBODY

1.5

1.0

0.5

N O R M A L I Z E D C U R R E N T T R A N S F E R R A T I O

I F – INPUT CURRENT – mA

8 PIN DIP, SO-80N O R M A L I Z E D C U R R E N T T R A N S F E R R A T I O

I F – INPUT CURRENT – mA

1.5

0.5

1.0

WIDEBODY

V F – FORWARD VOLTAGE –

VOLTS I F – F O R W A R D C U R R E N T – m A

8 PIN DIP, SO-8

V F –

FORWARD VOLTAGE – VOLTS

1000

100101.00.10.001

I F – F O R W A R D C U R R E N T – m A

WIDEBODY

Figure 6. Propagation Delay Time vs. Load Resistance.

Figure 5. Propagation Delay vs. Temperature.

Figure 4. Current Transfer Ratio vs. Temperature.

1.00.9

0.8

0.7

0.6

N O R M A L I Z E D C U R R E N T T R A N S F E R R A T I O

T A – TEMPERATURE – °C 8 PIN DIP, SO-8

1.11.00.90.80.70.660

N O R M A L I Z E D C U R R E N T T R A N S F E R R A T I O

T A – TEMPERATURE – °C

0.5

0.4

WIDEBODY

1.0

R L – LOAD RESISTANCE – (k ?)

t P – P R O P A G A T I O N D E L A Y – μs

8 PIN DIP, SO-8

R L – LOAD RESISTANCE – (k ?)

t P – P R O P A G A T I O N D E L A Y – μs

6.0

4.01.0

0.60.40.2WIDEBODY

1500

1000

500

0t p – P R O P A G A T I O N D E L A Y – n s

T A – TEMPERATURE – °C 8 PIN DIP, SO-8

1000800600

400

200

T A – TEMPERATURE – °C

WIDEBODY

t p – P R O P A G A T I O N D E L A Y – n s

Figure 9. Thermal Derating Curve, Dependence of Safety Limiting Value with Case Temperature per IEC/EN/DIN EN 60747-5-2.

Figure 8. Small-Signal Current Transfer Ratio vs. Quiescent Input Current.

Figure 7. Logic High Output Current vs. Temperature.

T A – TEMPERATURE – °C

10+410101001010+210+3I O H – L O G I C H I G H O U T P U T C U R R E N T – n A

8 PIN DIP, SO-8

I O H

– L O G I C H I G H O U T P U T C U R R E N T – n A

T A – TEMPERATURE – °C

10

10

10

10

WIDEBODY

? I F

?

I O – S M A L L S I G N A L C U R R E N T T R A N S F E R R A T I O I F – QUIESCENT INPUT CURRENT – mA 8 PIN DIP, SO-8

0.30

? I F ? I O

– S M A L L S I G N A L C U R R E N T T R A N S F E R R A T I O

I F – QUIESCENT INPUT CURRENT – mA

WIDEBODY

O U T P U T

P O W E R – P S , I N P U T C U R R E N T – I S

T S – CASE TEMPERATURE – °C O U T P U T P O

W E R – P S , I N P U T C U R R E N T – I S

0T S – CASE TEMPERATURE – °C

1000400600800200100300500700900

Figure 10. Frequency Response.

HCNW135/6

HCNW135/6

0.1

1.010100

-20-15-10

-5

+5T A = 25 °C

f - FREQUENCY - MHz

N O R M A L I Z E D R E S P O N S E - d B

6N135/6, HCPL-0500/1, HCPL-2502

V TYPICAL I = 9 mA F

O

6N135/6, HCPL-0500/1, HCPL-2502

Figure 12. Test Circuit for Transient Immunity and Typical Waveforms.

Figure 11. Switching Test Circuit.

O

F

= 1.5 μF

t V I F O

V

O

V O

https://www.360docs.net/doc/0e7351835.html,/semiconductors

For product information and a complete list of

distributors, please go to our web site.For technical assistance call:

Americas/Canada: +1 (800) 235-0312 or (916) 788-6763

Europe: +49 (0) 6441 92460China: 10800 650 0017

Hong Kong: (+65) 6756 2394

India, Australia, New Zealand: (+65) 6755 1939Japan: (+81 3) 3335-8152 (Domestic/Interna-tional), or 0120-61-1280 (Domestic Only)Korea: (+65) 6755 1989

Singapore, Malaysia, Vietnam, Thailand,Philippines, Indonesia: (+65) 6755 2044Taiwan: (+65) 6755 1843Data subject to change.

Copyright ? 2004 Agilent Technologies, Inc.Obsoletes 5989-0305EN December 20, 20045989-2112EN