Introduction to ATA 25 Floor Covering for Aircraft

Reference Title

25.28.103Adhesive change for carpet installation

25.28.126Specific installation of Non Textile Floor (NTF)

25.28.200Non Textile Floor (NTF) covering selection in galley, entrance areas and lavatories (SFE

standard I)

25.28.210Non Textile Floor (NTF) covering select. in galley, entrance areas and lavatories (SFE

standard II)

25.28.225Non Textile Floor (NTF) selection in lavatories (SFE standard)

25.28.103 - Adhesive change for carpet installation Objective

To select alternate adhesive for carpet installation.

Basic aircraft

Carpets are installed with dispersion-adhesive.

Description

On request an alternate adhesive of carpet is available:

the double-sided adhesive tape.

EPAC selection mode

Individual

Table 25-28-1 - Technical solutions description

TDU Title (Remarks)Appl.Weight (kg)

MWE/OWE/APL Equipment

reference

Equipment

supplier

Equipment

PN

QTY STS

02Installation of double-sided adhesive tape for carpet A318-100

A319-100

A320-200

A321-200

1.5/1.5/-1.5

1.5/1.5/-1.5

2.0/2.0/-2.0

2.0/2.0/-2.0

25.28.126 - Specific installation of Non Textile Floor (NTF)

Objective

To provide additional specific installation of NTF.

Basic aircraft

All NTF joints are welded (floormat to floormat) in all flat areas exposed to wear and tear, non PVC NTF except-ed.

Description

TDU 04: the NTF is installed in such a way that the joints are not in the main door way or walk ways in each gal-ley/entrance area.

TDU 07: sealing is applied at the outside (decor side) in-terface gap between all installed cabin monuments and the NTF in order to prevent migration of fluids under-neath or behind such monuments.

TDU 08: the NTF installation allows an easy replace-ment of NTF inside the galley without lifting the galley compartment.

The NTF split lines are neither underneath nor outside but inside the galley walls and there is one NTF joint for each galley compartment for easy replacement.TDU 09: extension of NTF installation at the aisle be-tween lavatories D and E in the aft passenger/crew/ser-vice door area.

Note

Welding

?silicone welding is technically not possible. For de-tailed description and information about the different NTF materials, please refer to the Airbus NTF selec-tion brochure.

?CN25.28.200/50, /51, /52 are silicone based NTF and must be sealed.

?weldability of non CCG / NTF brochure material to be checked.

?if the chosen NTF is not weldable or the customer re-quests the sealing of NTF joints, prior selection of CN25.28.126/11 is required.

EPAC selection mode

Individual

Table 25-28-2 - Technical solutions description

TDU Title (Remarks)Appl.Weight (kg)

MWE/OWE/APL Equipment

reference

Equipment

supplier

Equipment

PN

QTY STS

04Cutting pattern - Non Textile Floor A318-100 A319-100 A320-200 A321-200

07NTF sealing for all cabin monu-ments A318-100 A319-100 A320-200 A321-200

08NTF layout allowing easy replacement A318-100 A319-100 A320-200 A321-200

09NTF extension to lavatories D and E entrance area A318-100 A319-100 A320-200 A321-200

25.28.200 - Non Textile Floor (NTF) covering selection in galley, entrance areas and

lavatories (SFE standard I)

Objective

To select alternate vendor/material for NTF for galley and entrance areas, and lavatories.

Basic aircraft

Floors in galley and entrance areas, and lavatories are covered with SFE NTF material.

Description

Floors in galley and entrance areas, and lavatories are covered with SFE NTF material as selected by the cus-tomer via relevant TDU.

If vendor GERFLOR is selected:

?galley and entrance areas are covered with a SFE NTF assembly. An NTF surface layer from GER-FLOR is bonded onto a laminate by WULFMEYER (This assembly is produced by WULFMEYER who bond a NTF surface layer from GERFLOR onto a laminate).

?lavatory floor are covered with a SFE NTF surface layer only.

?If AVR175A is selected, lavatory, galley and entrance floor areas are covered with a SFE NTF "all in one"

assembly entirely made by GERFLOR. Information:

Due to the light weight construction of all-in-one NTF, the aircraft floor panel surface profile moisture barrier overlapping areas and seat rail traces may be visible under certain light angles (telegraphing) when this NTF is installed in galley and entrance floor areas. This is an optical phenomenon and shall have no influence on the NTF quality or NTF installation quality.

At some floor panel edges NTF waving may come up in cruise flight and disappear after landing. This is caused by the NTF and cabin floor normal dynamic flexibility, and shall have no influence on the NTF quality or NTF installation quality.

Airbus reserves the right to refuse any NTF telegraph-ing or waving related claim.

If vendor METZELER is selected:

?galley and entrance areas, and lavatories are cov-ered with a SFE NTF assembly entirely made by METZELER.

25.28.200 - Non Textile Floor (NTF) covering selection in galley, entrance areas and

lavatories (SFE standard I) (Continued)

NTF standard I is approved by AIRBUS with the follow-

ing properties:

?fulfillment of ABD0031 (smoke density and toxicity)

and JAR/FAR 25.853 Appendix F part I para.

(a)(1)(ii) airworthiness requirements and other appli-

cable airworthiness requirements

?dimension stability (shrinkage and stretch)

?impact resistance

?static and sliding friction

?temperature resistance

?abrasion and tear resistance

?peel strength.

EPAC selection mode

Individual

Table 25-28-3 - Technical solutions description

TDU Title (Remarks)Appl.Weight (kg)

MWE/OWE/APL Equipment

reference

Equipment

supplier

Equipment

PN

QTY STS

01NTF selection (SFE standard I) - GERFLOR Batiflex AVR160 -

SOLO A318-100

A319-100

A320-200

A321-200

Set of Non Textile

Floor covering

GERFLOR AVR 160

SOLO

1SFE

02NTF selection (SFE standard I) - GERFLOR Batiflex AVR160 -

TRESSE A318-100

A319-100

A320-200

A321-200

Set of Non Textile

Floor covering

GERFLOR AVR160-

TRESSE

1SFE

05NTF selection (SFE standard I) - GERFLOR Batiflex AVR175A -

ALTO

A318-100 : Subject to certification

A319-100 : Subject to certification

A320-200 : Subject to certification

A321-200 : Subject to certification A318-100

A319-100

A320-200

A321-200

Set of Non Textile

Floor covering

GERFLOR AVR175A-

ALTO

1SFE

06NTF selection (SFE standard I) - GERFLOR Batiflex AVR175A -

SOLO A318-100

A319-100

A320-200

A321-200

Set of Non Textile

Floor covering

GERFLOR AVR175A-

SOLO

1SFE

50NTF selection (SFE standard I) - METZELER Airfloor AFR - R

A318-100 : Subject to certification

A319-100 : Subject to certification

A320-200 : Subject to certification

A321-200 : Subject to certification A318-100

A319-100

A320-200

A321-200

Set of Non Textile

Floor covering

METZELER AIRFLOOR-

AFR-R

1SFE

51NTF selection (SFE standard I) - METZELER Airfloor AFR -

DA8A318-100

A319-100

A320-200

A321-200

Set of Non Textile

Floor covering

METZELER AIRFLOOR-

AFR-DA8

1SFE

52NTF selection (SFE standard I) - METZELER Airfloor AFR -

DS10

Under requalification process.

A318-100 : Subject to certification

A319-100 : Subject to certification

A320-200 : Subject to certification

A321-200 : Subject to certification A318-100

A319-100

A320-200

A321-200

Set of Non Textile

Floor covering

METZELER AIRFLOOR-

AFR-DS10

1SFE

TDU Title (Remarks)Appl.Weight (kg)

MWE/OWE/APL Equipment

reference

Equipment

supplier

Equipment

PN

QTY STS

Intentionally left blank

25.28.210 - Non Textile Floor (NTF) covering select. in galley, entrance areas and

lavatories (SFE standard II)

Objective

To select alternate vendor material for NTF for galley and entrance areas, and lavatories.

Basic aircraft

Floors in galley and entrance areas, and lavatories are covered with SFE NTF material.

Description

Floors in galley and entrance areas, and lavatories are covered with SFE NTF material as selected by the cus-tomer via relevant TDU.

If vendor GERFLOR is selected:

?Galley and entrance areas are covered with an SFE NTF assembly. A NTF surface layer from GERFLOR is bonded onto a laminate by WULFMEYER (This as-sembly is produced by WULFMEYER who bond a NTF surface layer from GERFLOR onto a laminate).?Lavatory floor areas are covered with a SFE NTF surface layer only.

?If AV 135 NTF is selected, lavatory, galley an en-trance areas are covered with a SFE NTF assembly, "all in one" entirely made by https://www.360docs.net/doc/1210085532.html,rmation:

Due to the light weight construction of all-in-one NTF, the aircraft floor panel surface profile moisture barrier overlapping areas and seat rail traces may be visible under certain light angles (telegraphing) when this NTF is installed in galley and entrance floor areas. This is an optical phenomenon and shall have no influence on the NTF quality or NTF installation quality.

At some floor panel edges NTF waving may come up in cruise flight and disappear after landing. This is caused by the NTF and cabin floor normal dynamic flexibility, and shall have no influence on the NTF quality or NTF installation quality.

Airbus reserves the right to refuse any NTF telegraph-ing or waving related claim.

25.28.210 - Non Textile Floor (NTF) covering select. in galley, entrance areas and

lavatories (SFE standard II) (Continued)

If vendor SCHNELLER is selected:

?Galley and entrance areas are covered with a SFE NTF assembly. A NTF surface layer from SCHNELLER is bonded onto a laminate by WULFM-EYER (This assembly is produced by WULFMEYER who bond a NTF surface layer from SCHNELLER onto a laminate).

?Lavatory floor areas are covered with a SFE NTF sur-face layer only.

If AerFusion or AerFusion via NTF is selected, lavatory, galley and entrance floor areas are covered with a SFE NTF assembly, "all in one" entirely made by SCHNELLER.

NTF standard II is approved by AIRBUS with the follow-ing properties:

?fulfillment of FAR/JAR 25.853 Appendix F part I para.

(a)(1)(ii) airworthiness requirements and other appli-

cable airworthiness requirements

?dimension stability (shrinkage and stretch)

?impact resistance

?static and sliding friction

?temperature resistance

?abrasion and tear resistance

?peel strength.Note

The NTF PN including colour shall be selected from the latest issue of NTF selection brochure.

Certain colours of NTF materials are subject to certifica-tion.

EPAC selection mode

Individual

Table 25-28-4 - Technical solutions description

TDU Title (Remarks)Appl.Weight (kg)

MWE/OWE/APL Equipment

reference

Equipment

supplier

Equipment

PN

QTY STS

07NTF selection (SFE standard II) - Top layer GERFLOR Batiflex

AVM282 - OPUS A318-100

A319-100

A320-200

A321-200

Set of Non Textile

Floor covering

GERFLOR AVM282-

OPUS

1SFE

09NTF selection (SFE standard II) - Top layer GERFLOR Batiflex

AVM282 - TRESSE A318-100

A319-100

A320-200

A321-200

Set of Non Textile

Floor covering

GERFLOR AVM282-

TRESSE

1SFE

10NTF selection (SFE standard II) - GERFLOR Batiflex AV302 -

SOLO A318-100

A319-100

A320-200

A321-200

Set of Non Textile

Floor covering

GERFLOR AV302-SOLO1SFE

11NTF selection (SFE standard II) - GERFLOR Batiflex AV302 -

BOLERO A318-100

A319-100

A320-200

A321-200

Set of Non Textile

Floor covering

GERFLOR AV302-

BOLERO

1SFE

30NTF selection (SFE standard II) - SCHNELLER Aermat 9500B -

30R A318-100

A319-100

A320-200

A321-200

Set of Non Textile

Floor covering

SCHNELLER AERMA T

9500B-30R

1SFE

33NTF selection (SFE standard II) - SCHNELLER Aermat 9000 -

90R A318-100

A319-100

A320-200

A321-200

Set of Non Textile

Floor covering

SCHNELLER AERMA T

9000-90R

1SFE

36NTF selection (SFE standard II) - SCHNELLER Aermat 9500BP

- 90R

A318-100 : Subject to certification

A319-100 : Subject to certification

A320-200 : Subject to certification

A321-200 : Subject to certification A318-100

A319-100

A320-200

A321-200

Set of Non Textile

Floor covering

SCHNELLER AERMA T

9500BP-90R

1SFE

47NTF selection (SFE standard II) - Top layer GERFLOR Batiflex

AVM282 metal - SOLO

A318-100 : Subject to certification

A319-100 : Subject to certification

A320-200 : Subject to certification

A321-200 : Subject to certification A318-100

A319-100

A320-200

A321-200

Set of Non Textile

Floor covering

GERFLOR AVM282-

METAL-SOLO

1SFE

49NTF selection (SFE standard II) - Top layer GERFLOR Batiflex

AVM282 - WOOD

A318-100 : Subject to certification

A319-100 : Subject to certification

A320-200 : Subject to certification

A321-200 : Subject to certification A318-100

A319-100

A320-200

A321-200

Set of Non Textile

Floor covering

GERFLOR AVM282-

WOOD

1SFE

61NTF selection (SFE standard II) - SCHNELLER AerFusion Via

90R

A318-100 : Subject to certification

A319-100 : Subject to certification

A320-200 : Subject to certification

A321-200 : Subject to certification A318-100

A319-100

A320-200

A321-200

Set of Non Textile

Floor covering

SCHNELLER AERFUSION-

VIA-90R

1SFE

62NTF selection (SFE standard II) - SCHNELLER AerFusion Via

91R

A318-100 : Subject to certification

A319-100 : Subject to certification

A320-200 : Subject to certification

A321-200 : Subject to certification A318-100

A319-100

A320-200

A321-200

Set of Non Textile

Floor covering

SCHNELLER AERFUSION-

VIA-91R

1SFE

63NTF selection (SFE standard II) - SCHNELLER AerFusion Via

92R

A318-100 : Subject to certification

A319-100 : Subject to certification

A320-200 : Subject to certification

A321-200 : Subject to certification A318-100

A319-100

A320-200

A321-200

Set of Non Textile

Floor covering

SCHNELLER AERFUSION-

VIA-92R

1SFE

TDU Title (Remarks)Appl.Weight (kg)

MWE/OWE/APL Equipment

reference

Equipment

supplier

Equipment

PN

QTY STS

64NTF selection (SFE standard II) - SCHNELLER AerFusion Via

93R

A318-100 : Subject to certification

A319-100 : Subject to certification

A320-200 : Subject to certification

A321-200 : Subject to certification A318-100

A319-100

A320-200

A321-200

Set of Non Textile

Floor covering

SCHNELLER AERFUSION-

VIA-93R

1SFE

TDU Title (Remarks)Appl.Weight (kg)

MWE/OWE/APL Equipment

reference

Equipment

supplier

Equipment

PN

QTY STS

25.28.225 - Non Textile Floor (NTF) selection in lavatories (SFE standard) Objective

To select alternate vendor/material for NTF covering in

lavatories.

Basic aircraft

Floors in lavatories, galley and entrance areas are cov-

ered with SFE NTF material.

Description

Floors in lavatories are covered with SFE NTF material

as selected by the customer via relevant TDU.

Note

The NTF PN including colour shall be selected from the

latest issue of NTF selection brochure.

Certain colours of NTF materials are subject to certifica-

tion.

NTF from Schneller (TDUs 03, 04, 05) are installed with-

out laminated surface.

EPAC selection mode

Individual

Table 25-28-5 - Technical solutions description

TDU Title (Remarks)Appl.Weight (kg)

MWE/OWE/APL Equipment

reference

Equipment

supplier

Equipment

PN

QTY STS

03NTF selection in lavatories (SFE standard II) -

SCHNELLER Panflor A318-100

A319-100

A320-200

A321-200

Set of Non Textile

Floor covering

SCHNELLER P ANFLOR1SFE

04NTF selection in lavatories

(SFE standard II) -

SCHNELLER Panflor - WOOD

A318-100 : Subject to certification

A319-100 : Subject to certification

A320-200 : Subject to certification

A321-200 : Subject to certification A318-100

A319-100

A320-200

A321-200

Set of Non Textile

Floor covering

SCHNELLER P ANFLOR-

WOOD

1SFE

05NTF selection in lavatories

(SFE standard II) -

SCHNELLER Panflor - STONE

A318-100 : Subject to certification

A319-100 : Subject to certification

A320-200 : Subject to certification

A321-200 : Subject to certification A318-100

A319-100

A320-200

A321-200

Set of Non Textile

Floor covering

SCHNELLER P ANFLOR-

STONE

1SFE

Intentionally left blank