Calorimeter量热器-Heat dissipation in a lithium ion cell(Hari Vaidyanathan)

Calorimeter量热器-Heat dissipation in a lithium ion cell(Hari Vaidyanathan)
Calorimeter量热器-Heat dissipation in a lithium ion cell(Hari Vaidyanathan)

Heat dissipation in a lithium ion cell

Hari Vaidyanathan a,*,William H.Kelly b ,Gopalakrishna Rao c

a

COMSAT Laboratories,Clarksburg,MD,USA b

William H.Kelly &Associates,Gaithersburg,MD,USA c

NASA Goddard Space Flight Center,Greenbelt,MD,USA

Received 8July 2000;accepted 2August 2000

Abstract

A comparative study of the heat dissipated by a 3.3A h Li x C/LiNiO 2cell and a 1.25A h Li x C/75%LiCoO 2,25%LiNiO 2cell was conducted through experimental heat rate measurements using a radiative calorimeter.The speci?c heat of the cell was determined experimentally to be 0.969J/8C g for the LiNiO 2cell and 0.946J/8C g for the Li x C/75%LiCoO 2,25%LiNiO 2cell.The Li x C/LiNiO 2cell had a higher self-discharge rate than the Li x C/75%LiCoO 2,25%LiNiO 2cell.The heat dissipated during discharge increased with the rate of discharge.During charge,initial endothermic cooling and subsequent exothermic heating beyond 55%state-of-charge were observed.At the C /2rate of discharge (medium rate),the heat dissipated was 17mW/cm 3for the Li x C/LiNiO 2cell and 11.2mW/cm 3for the Li x C/75%LiCoO 2,25%LiNiO 2cell.The experimental values obtained for the heat dissipation at various charge and discharge rates were used to calculate thermoneutral potentials of 3.698and 3.836V for the Li x C/LiNiO 2and Li x C/75%LiCoO 2,25%LiNiO 2cells,respectively.The proposed values for thermoneutral potential may explain the endothermic cooling during charge and the negative temperature coef?cient for cell voltage.#2001Elsevier Science B.V .All rights reserved.

Keywords:Heat dissipation;Lithium ion cell;Radiative calorimeter

1.Introduction

A commercial lithium ion battery that uses the ``rocking chair''concept (in which the lithium ions ``rock''from one state (cathode)to another (anode))was introduced in 1990[1]and has gained wide acceptance for a range of applica-tions due to attractive features such as high voltage,light weight,and small dimensions.The battery consists of a carbon anode and a lithiated metal-oxide cathode in an aprotic solvent containing a dissolved lithium salt [2].There is no metallic lithium in the cell.The cell voltage results from the difference in the activity of lithium ions in the carbon anode and lithium nickel oxide (or cobalt oxide)cathode.Performance features such as the variation of capacity with temperature and rate of discharge,self-dis-charge,voltage pro?les,and cycle life have been discussed at length by various authors [3,4].The cathode is the source of the lithium ions and is depleted to a value corresponding to Li 0.35NiO 2or Li 0.5CoO 2during charge.Cell voltage increases with increase in the state of charge,and at the charge termination voltage of 4.1V ,the anodic composition corresponds to Li 0.8C 6.The cell shows a mid-discharge

voltage of 3.5V ,which decreases as a function of the voltage termination value during charge.The cell cannot be over-charged or overdischarged.It undergoes self-discharge at a rate that is a function of temperature,anode structure,and the formulation of the electrolyte.The rate is lower than that occurring in conventional alkaline rechargeable batteries.Heat dissipation during discharge,charge,and self-dis-charge of batteries is an important parameter not only for the safe operation of the battery but also for extending its cycle and calendar life.In addition,the battery is susceptible to thermal runaway when heat is generated faster than it can be dissipated.Another thermal condition that affects the opera-tion of the battery is the development of thermal gradients and hot spots,which greatly accelerates the degradation of the electrolyte,anode,cathode,and separator.

The thermal characterization of lithium ion cells is more complex and fraught with dif?culties due to uncertainty regarding enthalpy values,reaction mechanisms,and side reactions.The side reactions that contribute to exothermic heating or endothermic cooling are the corrosion of copper,dissolution of lithium nickel-oxide and lithium cobalt-oxide,polymerization of the electrolyte,production of gases such as ethylene,propylene,hydrogen,and oxygen,and the hydration and formation of carbonates and ˉuorides.Math-ematical analysis of heat rates for lithium ion cells has

been

Journal of Power Sources 93(2001)112±122

*Corresponding author.Tel.: 1-301-428-4007;fax: 1-301-428-7747.E-mail address :hari.vaidyanathan@https://www.360docs.net/doc/3814183669.html, (H.Vaidyanathan).

0378-7753/01/$±see front matter #2001Elsevier Science B.V .All rights reserved.PII:S 0378-7753(00)00550-4

reported by Chen and Evans[5],calorimetric measurements of heat rates by Hong et al.[6]and thermodynamic calcula-tions by Deiss et al.[7].In[5±7],the authors report that the temperature coef?cient of cell open-circuit voltage is à0.4mV/K,the heat dissipation rate during C/2discharge is10mW/cm3,thermal runaway does not occur during normal battery operation,entropic heat is more than50% of the total heat and increases with increase in the rate of discharge,and there is a divergence in the calculated and measured values for the open-circuit potential.

The present study was conducted to determine the heat dissipation rates from Li x C/LiNiO2and Li x C/75%LiCoO2, 25%LiNiO2cells during charge and discharge,and then to measure thermal capacity and calculate thermoneutral potential as a function of state of charge.The experimental approach used a radiative calorimeter,and the measurements were performed under transient conditions.The radiative calorimeter is ideally suited for determining the heat rates of fractional watts because of its high sensitivity,which is 0.002W/8C for the radiative term,compared to1W/8C for the calorimetric constant for the conductive calorimeter. Heat leakage through the leads and sensing wires by con-duction can be calculated and compensated.Heat stored and heat dissipated are calculated separately.

2.Cell selection

The cells selected for this study were provided to NASA Goddard Space Flight Center for an evaluation program.The Li x C/LiNiO2cell was a cylindrical3.7A h cell fabricated in a stainless steel can containing a graphite anode with a glass-to-metal seal,polypropylene separator,and an electrolyte formulation consisting of LiPF6dissolved in a mixture of ethylene carbonate(EC)and dimethyl carbonate(DMC). The Li x C/75%LiCoO2,25%LiNiO2cell had a capacity of 1.25A h and contained the same type of graphite as the anode material,separator,and electrolyte,with a plastic-insulated seal and a puncture diaphragm,in a nickel-plated can.The dimensions were those of a type-18650cell.Both cell types contained spirally wound electrodes of different lengths and diameters.

3.Calorimeter

The calorimeter is designed for radiative transfer of heat from the cell to its surroundings[8].It consists of a0.5m3 copper chamber that is maintained atà1688C by circulating liquid nitrogen.The inside of the chamber is painted black, and the cell is suspended using a lacing cord.The calori-metric chamber is arranged in a bell-jar-type(45cm dia-meter and73cm tall)vacuum chamber,and a vacuum of 10à5Torr is maintained.

In preparing the cell for calorimetry,great care was taken to see that it had a distinct radiating surface.A2.54cm-wide thermofoil heater tape was wrapped around the cell and bonded to the cell case by means of epoxy.The heater taped area constituted the radiating surface,which was26.7cm2 for the LiNiO2cell and12.9cm2for the LiNiO2cell.Six thermocouples were installed at different areas of the cell, with care being taken not to contact any of the thermo-couples to the thermofoil heater.The thermocouples were distributed as follows:one at the cell cover,one at the bottom of the can,and four on the cylindrical region of the can.The thermocouple sensing wires,terminal leads,voltage sensing leads,and heater leads were bunched to create a wire bundle and insulated with multiple layers of aluminized Mylar.The exposed areas of the cell were also insulated with multiple layers of Mylar.The Mylar insulation is required to prevent heat loss through radiation from any surface other than the area wrapped with the heater tapes.A thermocouple was attached to the calorimeter chamber to ascertain theˉow of liquid nitrogen.Another thermocouple was attached to the end of the wire bundle under the Mylar insulation before it exited the chamber,so that the temperature reading could be used to calculate heat transferred by conduction.Fig.1 shows the test con?guration for the cell.Heat was applied to the cell through the thermofoil heaters in order to raise the cell temperature signi?cantly above that of the calorimetric chamber(à1688C).Thus,heat is radiated from the cell and follows the relationship

Q r es T4càT4s (1) where Q r is the heat radiated(W),e the emissivity,s the Stefan±Boltzmann constant(5X667?10à8W a m2K),T c the temperature of the cell(8C)and where T s is the temperature of the calorimeter(105K).

The radiative calorimetry determined the following: 1.Heater power setting:an approximate calculation of the heater power required to maintain the cell fromà5to 308C,using Eq.(1).

2.Calibration and heat radiated,Q r:a determination of steady-state temperatures for various values of applied heater power,and curve-fitting of the data to derive an expression for Q r.

3.Thermal capacity,C p:determined based on transient cooling and warm-up curves.

4.Conductive heat loss:the heat associated with conduc-tion through the lead and sensing wires is calculated using

Q cond

hA T càT wire bundle

L

(2) where Q cond is the heat transfer by conduction(W),h the effective thermal conductivity(W/cm8C)with the values used being3.75W/cm K for copper and0.21 W/cm K for constantan,A the cross-sectional area(cm2), T c the temperature of the cell(8C),T wire bundle the temperature of the wire bundle(8C)and where L is the length of wires and leads(cm).

H.Vaidyanathan et al./Journal of Power Sources93(2001)112±122113

5.Rate of energy stored,Q s:this is calculated using

Q s mC p d T

d t

(3)

where Q s is the rate of energy stored(W),m the mass of the cell(g),C p the specific thermal capacity of the cell (J/8C),d T c the temperature change of the cell(8C)and where d t is the elapsed time(s).

6.Heat dissipated from the cell,Q diss:the rate of heat dissipation from the cell is determined as follows:

Q diss Q hàQ ràQ condàQ s(4) where Q h is the heater power in watts.

The test conditions and values for the various parameters are given in Table1.

The function of the calorimeter described above differs markedly from that of conventional conductive calorimeters. Conductive calorimetry is performed under both steady-state and dynamic conditions.In the steady-state technique, the term mC p d T/d t is not used in the calculations.The conduction term is

Q cond hA T cellàT cal (5) where h is the heat transfer coefficient(W/cm8C),A the surface area of the cell(cm2),T cell the cell surface tempera-ture(8C)and where T cal is the calorimeter temperature(8

C).

Fig.1.Test schematic.

Table1

Test conditions

Parameter Value

Calorimeter size0.5m3,copper chamber

Calorimeter temperatureà1688C

Calorimeter pressure10à5Torr

Heat transfer mode Radiation

Cell temperature Average of three thermocouples located on the cell surface for the LiNiO2cell(two for the LiCoO2cell) Conductive correction Heat transfer through the wire bundle is included in the calculation

Heater tape Nichrome,12.9cm2

Data intervals60s

Charge/discharge Constant current

V oltage limits 4.1V for charge termination

2.5V for discharge termination

114H.Vaidyanathan et al./Journal of Power Sources93(2001)112±122

In this technique,radiation is neglected.The minimum heat that can be measured is38mW/8C,as stated in[6]. Radiative calorimetry,on the other hand,is performed in an environment where radiation is the major mode of heat transfer.The apparatus is simple,and the minimum heat that can be measured can be varied by adjusting the area of the radiating surface.The equivalent calorimetric constant is 1.8mW/8C.The resolution can be increased by decreasing the area of the radiating surface(by insulating most of the cell surface with multiple layers of aluminized Mylar). Radiative calorimetry is a transient technique ideally suited to determining the heat dissipated from a cell during charge and discharge.The main sources of error are the curve-?tting to obtain Q r,temperature,heater power,and heat leakage through the insulation.

4.Calibration

The power applied to the cell heater was set at several different values and the corresponding cell temperatures were measured at steady state and at open-circuit voltage. The cell temperature is determined based on an average of the values taken from two thermocouples mounted on the cylindrical surface of the cell.To allow for heat loss and gain through the voltage-sensing and power leads,heater power leads,and thermocouple leads,the conductive heat transfer from the cell through the leads was calculated by measuring the temperature difference at the beginning(cell surface) and end(point of exit from the calorimeter)of the wire bundles and inserting the values for the length and cross-section of the wires into Eq.(2).The calculated Q cond was 0.00137W/8C for the Li x C/LiNiO2cell and0.01118W/8C for the Li x C/75%LiCoO2,25%LiNiO2cell.The value for Q cond is higher for the Li x C/75%LiCoO2,25%LiNiO2cell due to the increased number of sensor wires and their shorter length.The calculated Q cond is deducted from the heater power to obtain Q r.Then,a steady-state curve is constructed by plotting the average temperature of the cell against Q r. Fig.2shows the plot obtained for the75%LiCoO2,25% LiNiO2cell.A similar plot was obtained for the LiNiO2cell. The following equations were then derived by curve-?tting: Q r 1X675?10à10 273 T avg 4

for the Li x C a757LiCoO2Y257LiNiO2cell(6) Q r 1X55?10à10 273 T avg 4for the Li x C a LiNiO2cell

(7) where Q r is the heat radiated,in watts,and T avg is the average of readings from the thermocouples installed on the cell.

5.Thermal capacity

The importance of using accurate values for thermal capacity in any thermal calculation is well documented.In this study,the thermal capacities for the cells were determined experimentally since the mass and speci?c heat of the various components in the cells were not known with certainty.

The thermal capacity of the Li x C/LiNiO2cell was deter-mined from the temperature transients observed during warm-up at a heater power of2.51W,and during cool-down using no heater power.The average cell temperature was converted to Q r using Eq.(6)for several time intervals,and Q cond was calculated using Eq.(2).The thermal capacity was then calculated using

MC p Q hàQ ràQ cond

d t

d T

(8)

The specific thermal capacity of the Li x C/LiNiO2cell was 111.5J/8C,and the normalized value was0.969J/8C g.The specific thermal capacity of the cell can also be calculated from the approximate mass and specific heat of cell com-ponents such as graphite,LiNiO2,EC,DMC,LiPF6,stain-less steel,copper,aluminum,and polypropylene.Precise values for mass and specific heat are not known;however,an approximation from the data provided by the cell manufac-turer regarding the components and their mass gave a value of102J/8C for thermal capacity for the LiC/LiNiO2cell, which compares well with the experimental value.

The thermal capacity of the Li x C/75%LiCoO2,25% LiNiO2cell was determined from the temperature transients observed during warm-up at a heater power of1.92W,and during cool-down.The speci?c thermal capacity of the cell was40.246J/8C,and the normalized value was0.946J/8C g.

6.Electrochemical characteristics

The impedance of the LiNiO2cell was measured at1kHz, and a value of110m O was obtained.The cell was stabilized at several temperatures by applying the proper heater power (using the calibration curve as a guide)and subjected to several charge and discharge capacity determination

cycles Fig.2.Variation of radiated heat with cell temperature.

H.Vaidyanathan et al./Journal of Power Sources93(2001)112±122115

at various rates and temperatures.The charging was done at constant current with a voltage limit of 4.1V ,and the discharging at constant current to a voltage limit of 2.5V .The cell had a capacity of 3.88A h at a discharge rate of 1A at 358C,with a mid-discharge voltage of 3.49V (taken at the midpoint of the discharge duration).The capacity decreased with decrease in temperature and increase in the rate of discharge.The capacity remaining in a charged cell after 72h in the open-circuited condition at 108C was 3.041A h,which translated to a loss of 4.9%.The loss for an Ni±Cd battery under the same conditions is 10%.Table 2sum-marizes the capacity,impedance,and self-discharge data obtained.

The performance features of the 75%LiCoO 2,25%LiNiO 2cell are characterized by a capacity of 1.27A h at 258C and a mid-discharge voltage of 3.6V .The capacity loss due to self-discharge in the 72h stand test was 3.39%.Cell impedance was 130m O .Fig.3shows the voltage pro?les obtained during the C /5rate of charge for the Li x C/75%

LiCoO 2,25%LiNiO 2cell,and during the C /7rate for the Li x C/LiNiO 2cell.Fig.4shows the voltage pro?les during the C /4rate for the Li x C/LiNiO 2cell,and at the C /2and C /5rates for the Li x C/75%LiCoO 2,25%LiNiO 2cell discharge.Note that the voltage pro?les show lower voltages during charge and discharge for the Li x C/LiNiO 2cell.The variation of cell voltage with state of charge followed the general trend published in the literature.7.Heat dissipation during charge

The power applied to the cell heater was adjusted in order to stabilize the cell at 258C.The Li x C/75%LiCoO 2,25%LiNiO 2cell was charged at 250mA to 4.1V ,after stabilizing at a heater power of 1.912W,and values for Q r ,Q s ,and Q diss were determined at 1min intervals.Fig.5shows the voltage and Q diss (heat rate pro?le).The thermal behavior of the cell is characterized by an initial rise in heat dissipation,fol-lowed by a minimum and endothermic cooling at about 25±30%state-of-charge,and a leveling-off towards the end of charge.The maximum endothermic rate is 0.015W.At the end of charge,Q diss is 0.039W.

Fig.6shows the temperature pro?le during charge at 250mA.The temperature curve shows an inˉection corre-sponding to endothermic cooling at about 25±30%state-of-charge and levels off toward the end of charge.

The charging reactions consist of intercalation of lithium ions to the graphite anode and deintercalation from the nickel-oxide cathode.The entropy change dominates the total heat dissipated during charge at C /5.The deintercala-tion from the cathode is believed to be endothermic.(Reac-tions at the carbon anode are not expected to be of any thermal consequence.)

The LiNiO 2cell was stabilized at 08C and charged at a constant current of 400mA.Temperature and heat dissipa-

Table 2

Electrochemical properties Parameter LiNO 2cell 75%LiCoO 2,25%LiNiO 2cell Mass (g)

11542.57V olume (cm 3)50.8116.54Diameter (cm) 3.4 1.8Height (cm)

5.1

6.5Electrical capacity (A h)08C,C /5rate 2.490.945108C,C /5rate 3.09 1.162258C,C /5rate ± 1.277258C,C /2rate 3.791 1.252358C,C /5rate 3.884±Impedance (m O )

110130Self-discharge in 72h (%)

4.9

3.39

Fig.3.V oltage profiles obtained during charge for the LiNiO 2and 75%LiCoO 2,25%LiNiO 2cells.

116

H.Vaidyanathan et al./Journal of Power Sources 93(2001)112±122

Fig.4.V oltage profiles obtained during discharge for the LiNiO 2and 75%LiCoO 2,25%LiNiO 2

cells.

Fig.5.Variation of heat rate during charge at C /5for the 75%LiCoO 2,25%LiNiO 2

cell.

Fig.6.Variation of temperature during charge at C /5for the 75%LiCoO 2,25%LiNiO 2cell.

H.Vaidyanathan et al./Journal of Power Sources 93(2001)112±122117

tion were monitored continuously until the voltage reached 4.1V .The average heat dissipation rate was 0.064W,or 0.00082W/cm 2of the surface area of the cell.The normal-ized heat rate was 0.0012W/cm 3.Heat dissipation increased rapidly at the beginning of charge,and then leveled off before rising towards the end of charge.

At the conclusion of the 400mA charge,the cell was trickle-charged at 60mA and the rate of heat dissipation was determined.Fig.7shows the variation in heat rate and voltage over time,and Fig.8shows the variation in voltage and temperature over time.The cell voltage increased during trickle charge and reached the limit of 4.1V in 1h.The values for the heat rate are shown as negative numbers to indicate its endothermic effect.The tendency for the heat rate to increase rapidly towards the end of the 400mA charge was not apparent,and endothermic cooling began,with a cooling rate of 0.0002W/cm 2.The cell temperature

showed a marginal decrease of 0.28C.The state of charge of the cell increased further during trickle charge.The obser-vation of marginal cooling during trickle charge is interest-ing and can be used to advantage in the charging scheme for aerospace applications.

8.Heat dissipation during discharge

The heat dissipation during discharge at different rates for the 75%LiCoO 2,25%LiNiO 2cells under test is shown in Fig.9.The pro?les show an initial maximum in the heat rate,followed by a minimum.This initial increase has also been reported by Hong et al.[6].The maximum heat rate during 625mA (C /2)discharge was 0.28W,and at 1.25A (C )rate,it was 0.55W.Thus,at a medium rate of discharge,heat dissipation was 11.21mW/cm 3,which is lower than

that

Fig.7.Variation of heat dissipation and voltage during trickle charge at 0.06A for the LiNiO 2

cell.

Fig.8.Variation of temperature and voltage during trickle charge at 0.06A for the LiNiO 2cell.

118H.Vaidyanathan et al./Journal of Power Sources 93(2001)112±122

obtained for the Li x C/LiNiO2cell.A general value of 10mW/cm3was reported by Chen et al.[5]based on mathematical calculations for a lithium ion cell.

The variation in heat dissipation rate for the LiNiO2cell during discharge at three different rates was determined,and the results are shown in Fig.10.At1A rate of discharge,the heat dissipation pro?le showed an initial maximum of 0.3W.The heat rate subsequently stabilized at0.23W before increasing to0.6W.This behavior was similar at 1.98A discharge,where the heat rate stabilized to0.8W from an initial maximum of1.04W.At3.59A discharge,the initial maximum was2.58W and the stabilized value was 2W.The heat dissipated at a medium rate of discharge was 17mW/cm3.Table3displays a short summary of the calorimetric data for the two types of cells which includes heat radiated and dissipated during discharge at the C/2rate. The conductive correction for the smaller75%LiCoO2,25%LiNiO2cell is larger,mainly due to the type of sense wires and thermocouple used.

The difference in the heat dissipation rates for the two types of cells at the C/2rate of discharge could result from a number of cell construction features,such as the dimensions of the spirally wound electrode coil,the amount of electro-lyte,and differences in the anode and cathode active mate-rial.Since graphite is the anode material in both cases,the cathode materials remain an important source for changes in heat dissipation at the anode.Thus,from the viewpoint of cell operation,there is an advantage in selecting LiCoO2as the cathode material.

The most striking feature of the heat dissipation is the initial maximum,followed by a reduction in the heat rate. The expected behavior was a gradual increase in the heat rate as discharge continued,followed by a very rapid rise towards the end of

discharge. Fig.9.Variation of heat rate at various rates of discharge for the75%LiCoO2,25%LiNiO2

cell.

Fig.10.Variation of heat dissipation rate with rate of discharge for the LiNiO2cell.

H.Vaidyanathan et al./Journal of Power Sources93(2001)112±122119

The total heat generated in the cell is attributable to entropic effect,ohmic effect,and electrochemical polar-ization.The heat rate attributable to electrochemical polar-ization is expected to be much lower at the beginning of discharge,and to increase gradually.The entropic contribution is a function of the chemical state of the participants in the main cell reaction.Ohmic heating is assumed to exhibit no signi?cant change during discharge and is expected to be lower than the heat due to entropy change.It is suggested that the initial increase in the heat rate during discharge is entropy-related.The main cell reaction is lithiation of the cathode,which is believed to be exothermic.The structure of Li x CoO 2and LiNiO 2have been studied and are believed to undergo reversible phase transitions due to switching between trigonal and mono-clinic crystal symmetries.Thackeray [9]has listed the lattice parameters as a function of lithium content in the Li x NiO 2structure and states that the monoclinic form exists from Li 0X 79to Li 0X 49.Bernardi et al.[10]reported that phase changes contribute to the total enthalpy and included them as a separate term,in addition to reaction enthalpy and the enthalpy of mixing [10].The suggested explanation for the initial increase,followed by minimum,in the heat rate curve is a phase change in the cathode active material.

9.Delayed heat evolution

The occurrence of nonfaradaic processes such as the chemical reaction of the electrolyte with the anode and cathode active material,phase changes in the cathode active material,and redistribution of lithium in the carbon anode can be inferred from the heat dissipation rates during open circuit periods following a discharge to 2.5V .Fig.11shows the heat rates obtained for the Li x C/75%LiCoO 2,25%LiNiO 2cell following completion of discharge at C /2and C rates.Initially,the heat rate ˉuctuated and then stabilized in both cases to about 0.01W.Although the heat rate is negligible,its occurrence points to a continuation of the processes.

10.Thermoneutral potential

The heat dissipation data obtained can be used to calculate the thermoneutral potential using E H à

Q diss

I

E L (9)

where Q diss is the heat dissipated (W,value is negative to indicate an exothermic reaction),E H the thermoneutral

Table 3

Summary of calorimetric data for the two types of cathodes Parameter

LiNO 275%LiCoO 2,25%LiNiO 2Heater area (cm 2)

26.712.9Specific thermal capacity (J/8C)111.5

40.246Conductive correction,Q c (W/8C)

0.001370.01118Heat radiated at end of discharge at C /2rate,Q r (W) 1.59 1.193Heat dissipated at end of discharge at C /2rate,Q diss (W)

1.13

0.285

Fig.11.Delayed heat after discharge for the 75%LiCoO 2,25%LiNiO 2cell.

120H.Vaidyanathan et al./Journal of Power Sources 93(2001)112±122

potential (V),I the discharge current (A)and where E L is the cell voltage during discharge (V).

This equation assumes that the discharge reaction is 100%ef?cient,and that parasitic reactions are neglected.

Fig.12shows the variation in thermoneutral potential for the LiNiO 2cell as a function of state of charge during discharge at 1A.The value for E H ,which varies from 3.726to 4.09V ,was calculated during various rates of charge and discharge.Table 4gives the values obtained.The average value calculated from the plateau is 3.698V .Fig.13shows the variation in calculated E H for the 75%LiCoO 2,25%LiNiO 2cell during charge and discharge.The three curves that show the variation in E H during discharge at C /5,C /2,and C rates have a plateau in the mid-discharge region.The values for E H at different rates of discharge show some variability;however,the overall variability in the plateau region is negligible.The curve obtained during charge at C /5shows very stable values for E H .Table

4

Fig.12.Variation of E H and E L during discharge at 1A for the LiNiO 2cell.

Table 4E H values Test regime

Value of E H (a)With 75%LiCoO 2,25%LiNiO 2cathode Discharge at 1A 3.8073Charge at C /2 3.8109Discharge at C /2 3.8037Charge at C /5at 58C 3.8456Charge at C /5at 188C 3.8726Discharge at C

3.8829Discharge at C /5at 58C 3.8357Average

3.8369(b)With nickel-oxide cathode Discharge at C /4 3.8883Charge at C /10 3.6657Discharge at C /2 3.6039Discharge at C 3.6350Average

3.6982

Fig.13.Variation of E H during discharge and charge for the 75%LiCoO 2,25%LiNiO 2cell.

H.Vaidyanathan et al./Journal of Power Sources 93(2001)112±122121

displays the average values obtained under each condition. The overall average value from the calculation is3.698V. The values obtained in this study for the thermoneutral potential of the75%LiCoO2,25%LiNiO2cell are in agreement with the negative temperature coef?cient for the voltage reported in the literature[2,7].It can be inferred from the thermoneutral potential that

the products of the discharge reaction are more ordered than the reactants;

endothermic cooling occurs at some point during charge; battery discharge will generate heat;

open-circuit potential will be less than the thermoneutral potential at all temperatures.

Ordinarily,thermoneutral potential can be used to calcu-late heat dissipation under various operating conditions, based on a knowledge of the voltage pro?les during charge and discharge.Before the values reported in this study are used,they should be con?rmed using cells produced under various manufacturing conditions.

11.Conclusions

A radiative calorimeter was used to obtain experimental heat rate dissipation data on a3.7A h lithium ion cell based on an LiNiO2cathode,and a1.25A h cell based on a mixture of LiCoO2and LiNiO2.The speci?c thermal capa-city of the cells was determined experimentally to be111.5 and40.24J/8C for the Li x C/LiNiO2cell and Li x C/75% LiCoO2,25%LiNiO2cell,respectively.The heat dissipated during discharge increased with the rate of discharge.Dur-ing charge,initial endothermic cooling and subsequent exothermic heating beyond55%state-of-charge were observed.At the C/2rate of discharge(which is considered a medium rate),the heat dissipated was17mW/cm3for the Li x C/LiNiO2cell and11.2mW/cm3for the Li x C/75% LiCoO2,25%LiNiO2cell.The difference in the heat dis-sipation rates is noteworthy and con?rms the belief that reactions at the cathode contribute more to total heat than those at the anode.The heat dissipation pro?le during discharge is also characterized by a minimum that is dif-ferent from that observed for Ni±Cd and Ni±H2cells.The minimum is attributed to phase changes in both the75% LiCoO2,25%LiNiO2and LiNiO2cells. Experimental values obtained for heat dissipation at various charge and discharge rates were used to calculate thermoneutral potential values of3.698and3.836V for Li x C/LiNiO2and Li x C/75%LiCoO2,25%LiNiO2cells, respectively.The proposed values for thermoneutral poten-tial can explain the endothermic cooling observed during charge,as well as the negative temperature coef?cient for cell voltage.The self-discharge rate for the Li x C/75% LiCoO2,25%LiNiO2cell was lower than for the Li x C/ LiNiO2cell.Thus,two important selection parametersDheat rate during discharge and self-discharge rateDfavor the use of LiCoO2over LiNiO2as the cathode material for lithium ion cells.

Acknowledgements

The authors would like to thank R.Clark for performing the calorimetric measurements.

References

[1]T.Nagura,in:Proceedings of the4th International Rechargeable

Battery Seminar,Deerfield Beach,FL,1990.

[2]J.R.Dahn,A.K.Sleigh,H.Shi,B.M.Way,W.J.Weydanz,J.N.

Reimers,Q.Zhong,V on Sacken,in:G.Pistoia(Ed.),Lithium Batteries,Chapter1,Industrial Chemistry Library,V ol.5,Elsevier, Amsterdam(London),1994.

[3]G.Nagasubramanian,R.G.Jungst,D.Ingersoll,D.H.Doughty,in:

Proceedings of the38th Power Sources Conference,Cherry Hill,NJ, 1998,p.493.

[4]B.V.Ratnakumar,M.C.Smart,S.Surampudi,in:Proceedings of the

38th Power Sources Conference,Cherry Hill,NJ,1998,p.503.

[5]Y.Chen,J.W.Evans,J.Electrochem.Soc.143(1996)2708.

[6]J.-S.Hong,H.Maleki,S.Al Hallaj,L.Redey,J.R.Selman,J.

Electrochem.Soc.145(1998)1489.

[7]E.Deiss,A.Wokaun,J.-L.Barras,C.Daul,P.Dufek,J.Electrochem.

Soc.144(1977)3877.

[8]H.Vaidyanathan,W.H.Kelly,in:Proceedings of the Intersociety

Energy Conversion Engineering Conference,San Diego,CA,V ol.1, Society of Automobile Engineers,Warrendale,PA,1992,p.209.

[9]M.M.Thackeray,J.Electrochem.Soc.142(1995)2538.

[10]D.Bernardi,E.Pawlikowski,J.Newman,J.Electrochem.Soc.132

(1985)5.

122H.Vaidyanathan et al./Journal of Power Sources93(2001)112±122

第二制冷剂量热器法

.第二制冷剂量热器法 本实验采用国标(GB5773-04)提出的对容积式制冷压缩机性能测试的主要试验方法──第二制冷剂量热法,对制冷压缩机的制冷量和输入功率进行测定。根据标准,本试验方法适用于名义功率不小于0.75kW的容积式制冷压缩机的性能试验。 第二制冷剂量热器法是通过第二制冷剂量热器间接测定制冷量,是利用安置在第二制冷剂量热器内部的电加热管发出的热量来消耗蒸发器盘管所产生的制冷量。 本试验装置有二种制冷剂,其中第一制冷剂为R22,第二制冷剂为R11。第二制冷剂 量热器是一个密闭的受压的隔热容器,安置在该量热器内的蒸发器盘管悬挂在容器的上部,电加热管安装在容器的底部并被容器内的第二制冷剂浸没。第一制冷剂在制冷系统中循环,在第二制冷剂量热器的蒸发器盘管中蒸发制冷;输入第二制冷剂量热器的热量主要是电加热管供给(量热器的漏热量应不超过5%),量热器内的第二制冷剂被加热汽化,形成的第 二制冷剂蒸汽在顶部蒸发器盘管外表面冷凝,重新回到液面。这样,制冷系统所产生的冷量被输入的热量通过第二制冷剂这中间介质间接消耗,当试验系统的热力状态趋于稳定,表明量热器内趋于动态热平衡。 当系统处于热平衡时,其热平衡方程式为: Q0=N h+?Q l (W) 式中:Q0──发器盘管制冷量,W; N h──加热功率,W; △Q l──第二制冷剂量热器的热损失(外界传入为正),W。 图1全封闭式制冷压缩机性能试验装置系统图 a、全封闭式制冷压缩机 b、冷凝器 c、节流阀 d、蒸发器盘管 e、第二制冷剂量热器 f、电加热管 g、静压水箱 h、第二制冷剂压力表 i、电功率表 j、制冷压缩机吸气压力表 k、制冷压缩机排气压力表l、冷凝压力水量调节阀

巴尔扎克简介

巴尔扎克简介(1799~1850) 法国小说家.1799年5月20日生于巴黎以南的图尔城, 1850年8月18日卒于巴黎.巴尔扎克的一生,处于19世纪前半期的50年,经历了拿破仑帝国的战火纷飞的岁月,动荡不安的封建复辟王朝,以及以阴谋复辟帝制的路易□波拿巴为总统的第二共和国.他用总标题为《人间喜剧》的一系列小说,反映了剧烈的社会变革时期的法国生活. 巴尔扎克出生后不久就被送到附近的乡村去寄养. 上小学后一直到中学毕业,他始终寄住在宿舍里,没有能回 家过一段比较长的日子,享受家庭生活的温暖.离开家庭的童年生活的痛苦使他毕生难忘. 巴尔扎克的父亲原姓巴尔沙,是个精明强干的人. 他来自农村,幼年时跟当地教士学了一点文化,中年致富,在外省当过副市长,供应军粮的承包商,在巴黎经营过呢绒商业,当过巴黎驻军的军需负责人,是一个白手起家的资产者. 1816年,17岁的巴尔扎克结束中学的学业后进大学法科,并在文科旁听.18岁时,先后在诉讼代理人和公证人的办事处当见习生或书记. 从20岁开始,巴尔扎克决定从事文学创作.他在巴黎贫民区租了一间房顶上的阁楼,由父母供给极有限的一点生活费,埋头写作.他的第一部作品是五幕诗体悲剧《克伦威尔》,这是一部完全失败的作品,没有引起任何人的兴趣.接连又写了十多部小说,有的是自己所写,有的是和别人合写.这一阶段他所写的小说全用笔名发表.这些作品并没有给他带来生活所需要的物质条件,他只好暂时放弃文学.1826年借钱出版了一部普及版的《莫里哀全集》,接着又出版一部拉封丹寓言诗集, 销路不佳,亏损负债9,000法郎.后又借债经营印刷厂和铸字厂,均以赔本告终.他前后负债共达6万多法郎. 从1828年夏季开始,巴尔扎克决定重新回到文学事业上来.他写了一部以布列塔尼封建势力武装叛乱反对共和国为题材的小说《最后一个舒昂党人》(后来编入《人间喜剧》,改名《舒昂党的人们》).这是巴尔扎克所写的第一部严肃的文学作品,第一次用巴尔扎克真姓名发表.此书问世,初步奠定了作者在文学界的地位. 接着发表小说《婚姻生理学》,在读者之间引起广泛注意.1831年他的新著《驴皮记》出版,巴尔扎克立即成为法国最负盛名的作家之一. 1819到1829年,是巴尔扎克在文学事业上的探索阶段.从1829年开始,一直到1848年,是他创作《人间喜剧》的时期,也是他文学事业的全盛时期.他用超人的才智与精力,在不到20年的时间内,共创作小说91部.平均每年产生作品四,五部之多.他每日伏案一般都在10小时以上,常常连续工作18小时.有时文思如泉涌,或者为了赶写稿子,他一连几天废寝忘餐,夜以继日地劳动.根据阿尔贝·贝干教授提供的材料,巴尔扎克的杰作《高老头》(原名《高立欧老爹》)是他用三天三夜一气呵成的. 什么是《人间喜剧》的作者的创作动力人们说是因为他负债过多,需要用稿费还债.巴尔扎克年轻时经营印刷出版业确曾负债巨万.但从他成为名重一时的小说家之后,他的收入丰厚,出版商争着和他签订合同,不惜重金预约他尚未完成或尚未动笔的小说稿,早年的债务早已还清.名作家巴尔扎克生活阔绰,醉心于豪华的排场.他在巴黎同时安置了几处住宅和别墅,出门坐最富丽的马车,驾着骏马;仆役都穿制服;他也服饰华贵, 出入于名门大户的沙龙.由此可见,他的勤奋创作,绝对不是由于贫困. 巴尔扎克从年轻时开始就自信有很高的文学才能, 对文学有极大的抱负.他不舍昼夜地勤奋写作,主要因为有一股激情在内心沸腾,促使他充分发挥自己的才能, 要求在文艺界做一番伟大的事业.在他的书室里,有一座作为摆饰的小型拿破仑塑像.在塑像座盘边上,巴尔扎克亲笔写着:"他用宝剑未能完成的大业,我将用笔杆来完成." 巴尔扎克要完成的伟大事业就是《人间喜剧》这座巍峨的文学里程碑.第一次在这位小说家笔下出现《人间喜剧》这个名词是在1813年.毫无疑问,《人间喜剧》的命名是受但丁长诗《神圣喜剧》(中译《神曲》)标题的启发.1841年,巴尔扎克确定了这个庞大的创作计划.当时有四家出版商和巴尔扎克签订合同,合资承包《人间喜剧》的出版工作.1842年,巴尔扎克写了《人间喜剧·导言》,阐述他写作这部史无前例的文学巨著的宗旨.1845年巴尔扎克亲笔写的《人间喜剧总目》,一直保存到现在.根据这个《总目》,《人间喜剧》分为三大部分:《风俗研究》,《哲理研究》和《分析研究》. 《风俗研究》内容最为丰富,包括小说最多.因此这一部分又分为六个门类:1.《私人生活场景》,2.《外省生活场景》,3.《巴黎生活场景》,4.《政治生活场景》, 5.《军队生活场景》,6.《乡村生活场景》.《私人生活场景》包括32部小说,其中4部当时已有提纲,尚未起稿.已经完成的28部之中包括著名的《高老头》(1834), 《猫滚球布店》(1830),《夏倍上校》(1832)和《三十岁的女人》(1831~1834)等.《外省生活场景》包括17 部小说,其中6部尚未完成;已经发表的11部中包括《欧也妮·葛朗台》(1833),《幽谷百合》(1835)和《幻灭》(1837~1843)等.《巴黎生活场景》共有20部小说, 其中6部尚未产生;在已经发表的小说中有《金目少女》 (1834),《纽沁根银行》(1838),《塞沙·皮罗多兴衰记》(1837),

高中语文 名著导读《高老头》巴尔扎克简介素材 新人教版必修3

巴尔扎克简介 巴尔扎克(Honore de Balzac,1799~1850),他是19世纪法国伟大的批判现实主义作家,欧洲批判现实主义文学的奠基人和杰出代表。一生创作96部长、中、短篇小说和随笔,总名为《人间喜剧》。其中代表作为《欧也妮·葛朗台》、《高老头》。100多年来,他的作品传遍了全世界,对世界文学的发展和人类进步产生了巨大的影响。马克思、恩格斯称赞他“是超群的小说家”、“现实主义大师”。 巴尔扎克出生于一个法国大革命后致富的资产阶级家庭,法科学校毕业后,拒绝家庭为他选择的受人尊敬的法律职业,而立志当文学家。为了获得独立生活和从事创作的物质保障,他曾试笔并插足商业,从事出版印刷业,但都以破产告终。这一切都为他认识社会、描写社会提供了极为珍贵的第一手材料。他不断追求和探索,对哲学、经济学、历史、自然科学、神学等领域进行了深入研究,积累了极为广博的知识。 1829年,巴尔扎克完成长篇小说《朱安党人》,这部取材于现实生活的作品为他带来巨大声誉,也为法国批判现实主义文学放下第一块基石,巴尔扎克将《朱安党人》和计划要写的一百四五十部小说总命名为《人间喜剧》,并为之写了《前言》,阐述了他的现实主义创作方法和基本原则,从理论上为法国批判现实主义文学奠定了基础。 巴尔扎克在艺术上取得巨大成就,他在小说结构方面匠心独运,小说结构多种多样,不拘一格、并善于将集中概括与精确描摹相结合,以外形反映内心本质等手法来塑造人物,他还善于以精细人微、生动逼真的环境描写再现时代风貌。恩格斯称赞巴尔扎克的《人间喜剧》写出了贵族阶级的没落衰败和资产阶级的上升发展,提供了社会各个领域无比丰富的生动细节和形象化的历史材料,“甚至在经济的细节方面(如革命以后动产和不动产的重新分配),我学到的东西也要比从当时所有职业历史学家、经济学院和统计学家那里学到的全部东西还要多”。(恩格斯:《恩格斯致玛·哈克奈斯》) 巴尔扎克以自己的创作在世界文学史上树立起不朽的丰碑。

巴尔扎克

巴尔扎克 1、巴尔扎克的文学史地位 巴尔扎克是法国伟大的小说家,是19世纪批判现实主义文学的主要代表。在20年间呕心沥血写作实践中,巴尔扎克在世界文学史上构筑了一座举世无双的巍峨大厦——《人间喜剧》,而他自己则成了“文学中的拿破仑”。 马克思非常推崇巴尔扎克,认为他“对现实关系具有深刻理解”。恩格斯赞誉他的作品有着“了不起的革命辩证法”,并在《致玛·哈克奈斯》一信中对他作了精辟的论述。 2、生平与创作概况 A.全称: xx·xx·巴尔扎克 B.本姓: xx C.生卒____年__月__日: 1799.5.20— 1850.8.18 D.出生地: xx E.家庭: 中产阶级之家 F.教育:1816年结束中学学业 G.主要经历:

1819-1829年,开始写作小说; 1825年起出版图书,开办印刷厂,铸造铅字,以欠债6万法郎告终; 1828-1850年,全力创作《人间喜剧》。 H.主要成就: 包括90余部长篇小说、中篇小说、短篇小说的文学巨著《人间喜剧》。 3、巴尔扎克的创作道路 1819-1829年,探索阶段;1819年,立志当作家。1820年,写作悲剧《克伦威尔》失败,开始创作神怪小说,也未获成功。此后至1828年前,屡屡经商失败,债台高筑。1828年夏起重走文学道路。1929年以真名发表历史小说《朱安党人》,初获成功,在文坛站稳脚跟。 1829-1845年,黄金时代;巴尔扎克怀着做“文学上的拿破仑”的雄心壮志,孜孜不倦地创作,建构着《人间喜剧》这座艺术大厦,接连发表了许多杰作,如《高布赛克》 (1830)、《驴皮记》 (1831)、《xx·xx》 (1833)、《xx》 (1834)、《无神论者做弥撒》 (1836)、《xx银行》 (1837)、《幻灭》(1837-1843)和《农民》 (1845)等。 1846-1850年,晚期。1848年前,巴尔扎克陆续完成了《贝姨》

压缩机检测方法和参数

压缩机检测方法和参数—压缩机性能测试 一、前言 制冷压缩机是制冷装置中最主要的设备,是制冷系统的动力装置和主机,相当于制冷机的心脏。它使制冷剂在系统的管路中循环,把来自蒸发器的低温低压制冷剂蒸汽压缩成高温高压的制冷剂蒸汽再排入冷凝器。 压缩机的作用可总结为: 1)从蒸发器中吸出蒸汽,以保证蒸发汽内一定的蒸发压力。 2)提高压力(压缩)以创造在较高温度下冷凝的条件。 3) 输送制冷剂,使制冷剂完成制冷循环。 压缩机性能的好坏直接影响到整机的制冷效果。而且,压缩机与制冷系统的匹配是否合理,不但涉及到整个装置的成本,而且对使用寿命和能耗均有影响,所以对压缩机的性能及有关参数的测试是非常有必要的。 对 压缩机性能的测试主要是测定压缩机运行时相关温度、压力、液位、转速、功率、振动、噪声、制冷剂流量、制冷量,其中制冷剂流量、制冷量及规定工况下的制冷 量是测试的重点。压缩机测试完后,需要对测试数据参照国家标准进行判断分析,以找出压缩机结构设计中问题,或者判断该压缩机是否运行良好。 本文将先对压缩机的测试原理、方法和相关规定做一个简单介绍,然后对测试过程进行描述,并对测试后数据进行分析、评价。以此对压缩机检测与分析的全过程进行描述和分析,不到之处,请大家批评指正。 二、压缩机测试的相关规定 为保证测试的统一性和结果的可靠性,国家规定了压缩机测试的相关标准,而该标准也即国际标准ISO 917-1974 中的《制冷压缩机的试验标准》。 2.1 一般规定 2.1.1 排除试验系统内的不凝性气体.确认没有制冷剂的泄漏. 2.1.2 系统内应有足够的符合有关标准规定的制冷剂.压缩机内保持正常运转用润滑油量. 2.1.3 循环的制冷剂液体内含油量应不超过2%(以质量计). 2.1.4 压缩机吸、排气口的压力一温度在同一部位测量,该测点应在吸、排气截止阀外(不带阀的封闭 压缩机为距机壳体)0.3m的直管段处。 2.1.5 排气管道上应设置有效的油分离器. 2.1.6试验系统装置的周围不应有异常的空气流动。 2.1.7 试验装置环境温度为30±5℃。 2.1.8 提供测量含油量而抽取制冷剂??—油混合物样品的设备。 2.2 试验规定 2.2.1 压缩机性能试验包括主要试验和校核试验,二者应同时进行测量。 2.2.2 校核试验和主要试验的试验结果之间的偏差应在±4% 以内,并以主要试验的测量结果为计算依 据。 2.2.3 压 缩机试验时,系统应建立热平衡状态,试验时间一般不少于1.5h。测量数据的记录应在试验 工况稳定半小时后,每隔20min测量一次,直至连续四次的测量 数据符合规定为止。第一次测量到第四次测量记录的时间称为试验周期,在该周期内允许对压力、温度、流量和液面作微小的调节。 2.2.4 主要试验方法 a. 第二制冷剂量热器法 b. 满液式制冷剂量热器法 c. 干式制冷剂量热器法 d. 制冷剂气体流量计法 2.2.5 校核试验方法 a. 水冷冷凝器量热器法 b. 制冷剂液体流量计法 c. 压缩机排气管道量热器法 2.3 测量仪表和精度的规定 2.3.1 一般规定 2.3.1.1 试验用仪表的类型,可采用一种或数种进行测量。 2.3.1.2 试验用仪表应在有效使用期内,并应有近期经国家计量部门或有关部门校正的合格证明。 2.3.2 温度测量仪表和精度 2.3.2.1 仪表:玻璃水银温度计、热电偶、电阻温度计、半导体温度计和温差计。 2.3.2.2 精度: a. 量热器的加热或冷却介质和制冷剂的进、出口温度:准确度±0.1℃; b. 冷凝器用于校核试验时的冷却水温度:准确度±0.1℃; c. 压缩机吸气温度、流量节流装置前温度:准确度±0.1℃; d. 其它温度:准确度±0.2℃; 2.3.2.3 温度测量的规定:

巴尔扎克作品经典语录大全100句

巴尔扎克作品经典语录大全100句 1、男子的才对于德而言,就和美貌之于女子差不多:能给人以希望。——巴尔扎克《莫黛斯特·米尼翁婚约》 2、苦难好比一道神奇的符箓,能加强我们的天性,使猜忌与凶恶的人愈加猜忌愈加凶恶,慈悲的人愈加慈悲。——巴尔扎克《夏倍上校》 3、真正的考验是在痛苦和幸福上。当两个人通过了这两种人生的考验,在这过程中每人的优缺点都暴露无遗,也观察了彼此的性格时,他们就可以手携手一直走到坟墓了。——巴尔扎克《莫黛斯特·米尼翁婚约》 4、在爱情方面,别有用心的虚假总比真面目可爱,就因为此,才有许多男人肯在一般手段高明的女骗子身上挥金如土。——巴尔扎克 5、人类所有的力量,只是耐心加上时间的混合。所谓强者是既有意志,又能等待时机。守财奴的生活,便是不断的运用这种力量为自我效劳。他只依赖两种情感:自尊心与利益。但利益既是自尊心的实际表现并且是真正优越的凭据,所以自尊心与利益是一物的两面,都从自私自利来的。这种人物涉及所有的情感,可以说集情感之大成,而我们个个人都跟他们一脉相通。哪有什么全无欲望的人?而没有金钱,哪个欲望够满足?——巴尔扎克《欧叶妮·葛朗台》 6、精神生活与肉体生活一样,有呼也有吸:灵魂吸收另一颗灵魂的感情来充实自己,然后以更丰富的感情送回给人家。人与人之间要没有这点美妙的关系,心就没有了生机:它缺少空气,它会受难,枯萎。——巴尔扎克《欧叶妮·葛朗台》 7、逆境不就是命运的试金石吗? ——巴尔扎克《高

老头》8、"L'amour n'est pas seulement un sentiment, il est aussi un art. 爱不光是一种感情,也是一门艺术。- Honoréde Balzac 巴尔扎克-——巴尔扎克《网络名言集》"9、感情等于才分。感受是了解的对手,正如行动是思维的抗衡。一个有天才的朋友可以通过友情、领会,和他并驾齐驱。一个常人有感情作基础,就可以比倒最伟大的艺术家。这说明女人为什么爱着一些“蠢才”。——巴尔扎克10、到处是真苦难,假欢喜。——巴尔扎克《高老头》11、哪里有穷困,哪里就有苦难。苦难,穷困,蓄势极猛,苦了,穷了,斯滥矣,大权在握,就会滥用,其理自同。——巴尔扎克《乡村医生》12、做点好事,待人要仁慈、宽厚;总之,用你的谦虚来避免厄运吧。——巴尔扎克13、苦难对于人生是一块垫脚石……对于能干的人是一笔财富,对于弱者是个万丈深渊。——巴尔扎克14、目的高尚,会使所做的事情都同样高尚。——巴尔扎克15、实笃一清如水的生活,诚实不欺的性格,不论身处哪个阶级,就算心术最坏的人,也会对之肃然起敬。——巴尔扎克16、长命也许不够好,美好的生命却够长。——巴尔扎克17、人们有多少需求,就能创造多少财富。——巴尔扎克18、艺术就是用最小的面积,惊人地集中最大量思想。——巴尔扎克19、他不断地处于与人奋斗、与天地奋斗之中,没有功夫去尽情卖弄。只有花花公子才会大肆卖弄,迫不及待地将转瞬即逝的一季庄稼收割下来,那种自尊与不管是什么东西,凡从它手下经过就要抽税的海关相差无几。——巴尔扎克20、年轻时费过力气学到的东西,即使是无聊对我们也有用。——巴尔扎克21、拐弯抹角的路成不了

巴尔扎克——素材

巴尔扎克出生于一个法国大革命后致富的资产阶级家庭,法科学校毕业后,拒绝家庭为他 选择的受人尊敬的法律职业,而立志当文学家。为了获得独立生活和从事创作的物质保障,他曾试笔并插足商业,从事出版印刷业,但都以破产告终。这一切都为他认识社会、描写 社会提供了极为珍贵的第一手材料。他不断追求和探索,对哲学、经济学、历史、自然科学、神学等领域进行了深入研究,积累了极为广博的知识。 1822年正当巴尔扎克倍受冷遇,痛苦绝望的时刻,结识了贝尔尼夫人。贝尔尼夫人的母亲 曾是王后的侍女,对宫廷的生活,交际的秘密和妇女的命运十分熟悉。贝尔尼夫人比巴尔 扎克大22岁,具有完美的娇柔感,高雅的谈吐,沁人肺腑的同情心,以及慈祥的母爱。这一切深深吸引着巴尔扎克,使巴尔扎克感受到从小没有领略过的母爱般的温情。她对他的 一生产生了重大的影响。巴尔扎克把她称为他的母亲、朋友、家属、伴侣和顾问。[1] 1829年,巴尔扎克完成长篇小说《朱安党人》。历史小说《朱安党人》(1829)是巴尔扎 克用真名发表的 奥诺雷·德·巴尔扎克 第一部作品,描述1800年法国布列塔尼在保皇党煽动下发生的反对共和国政府的暴动。作者赋予英勇的共和国军人以应有的光彩,但也大大美化了朱安党首领孟多兰侯爵,表现出 他当时对贵族的同情。为了写这部小说,他曾细心研究有关暴动的历史文献,亲自去布列 塔尼调查山川形势和农民生活,访问暴动的目击者和参加者,还从友人柏尔里公爵夫人那 里收集许多关于朱安党人的掌故。从写神怪小说过渡到写历史小说,是巴尔扎克走向批判 现实主义的第一个重要步骤。他在《朱安党人》中描写的不是古代历史,而是属于当代社 会生活范畴的重要事件。着重反映当代社会生活,正是巴尔扎克日后所写的《人间喜剧》 的一个特点。 从1829年写《朱安党人》起,巴尔扎克的创作开始进入成熟时期,即《人间喜剧》时期(1829-1848)。在三、四十年代,他除致力于文艺创作以外,还出入巴黎上流社会的沙龙,为几种报刊撰稿,他接触的生活面非常广泛。[2] 巴尔扎克从这时期起,就在现实主义理论方面进行深入探索。他认为小说家必须面向现实 生活,使自己成为当代社会的风俗史家;又认为小说家的任务不仅在于摹写社会现象,还 须阐明产生这些现象的原因,指出人物、 影视剧中奥诺雷·德·巴尔扎克 欲念和事件背后的意义。在塑造人物的问题上,他强调特性,也强调共性;他说诗人的使 命在创造典型,使典型个性化,个性典型化;又说典型人物应该把那些多少和他类似的人 的性格特点集于一身。他还强调艺术必须为社会服务;认为艺术家不仅描写罪恶和德行, 而且要指出其中的教育意义;艺术家必须同时是道德家和政治家。 1830年4月,巴尔扎克《人间喜剧》中《私人生活场景》两卷出版了。然而,他深深地为 法国文学创作者的处境担忧。虽然法国于1791年颁布的《表演法令》和1793年颁布的

外国文学史 巴尔扎克汇编

第五节巴尔扎克与《高老头》分析 一、巴尔扎克简介(1799-1850) 1、《人间喜剧》的创作:《风俗研究》《哲理研究》《分析研究》,是一部关于19世纪法国的“包罗万象的社会史”。 (1)主题上要写出“一个完整的社会”,艺术上要呈现一个“统一、独创、新鲜的整体”。 (2)主题思想:反映出资产阶级取代贵族阶级的时代潮流。 A、资产阶级的发迹史。《赛查·皮罗托盛衰记》《欧也妮·葛朗台》《纽沁根银行》 B、贵族阶级的衰亡史。《古物陈列室》 C、金钱成为社会的轴心,操纵着社会关系,这不仅反映在广义的政界、社交界等社会层面,而且反映在最亲密的家庭关系中。 (3)艺术特征: A、艺术形式的多样化和富于变化,或客观描述,或转述故事,或深入人们的情感中探讨。 B、在典型环境中塑造具有典型意义的人物形象,人物性格与物质化的社会环境水乳交融。 C、作品文本的相互交织。《人间喜剧》的一部作品中的人物形象会在多部作品中出现,人物的命运具有时间上的连续性,因而众多作品相互勾连,构成一部完整的社会生活的记录。如《高老头》中鲍赛昂夫人的凄凉结局、拉斯蒂涅的飞黄腾达。 D、写实与幻想交相辉映,突出金钱统治下的法国社会的疯狂喧嚣。《萨拉辛》

二、《高老头》分析([法]巴尔扎克著,张冠尧译,北京:人民文学出版社,2003年) 一、作品背景与主要内容介绍 当时的法国现实是,资产阶级已经获得彻底的胜利,而贵族阶级逐渐地退出历史舞台。这样资本主义的生产关系的重要基础即金钱在社会生活中占据着绝对地位,支配着各种社会关系,并且渗透在人们的亲情、友情和爱情中。 《高老头》是法国批判现实主义大师巴尔扎克最具代表性的作品之一,充分展现了金钱的罪恶与对人类美好感情与人性的腐蚀作用。 二、作品简介 作品中有着两条线索,一条是高老头的命运正由盛转向衰败,另一条是拉斯蒂涅正步步高升,但展现的是相同主题。拉斯蒂涅为高老头奔走于两地之间,作品通过他的奔走将这两条线索结合起来,凸现法国巴黎各个社会阶层的生活。从代表着法国社会底层的缩影的伏盖公寓,到法国的上流社会人人趋之若骛的地方鲍赛昂夫人的门庭和舞会;从社会的底层人物伏盖公寓中住客之间的关系,到贵族与银行家的家庭关系,《高老头》描写得详尽细致,淋漓尽致。与法国社会各阶层的接触使拉斯蒂涅逐步认识到法国社会的本质,即金钱至上,人人为己,但这也使他彻底泯灭的人性的良知。 三、作品主题 1、金钱主宰着社会的一切关系 2、高老头的沦落意味着,在资本阶级上升时期金钱对社会的统治和金钱至上的原则的冲击下,传统的宗法制家庭伦理关系彻底解体。 四、拉斯蒂涅的人物形象分析 作者塑造高老头人物形象的意义,不仅是想通过高老头的命运对作品中另一主要人物拉斯蒂涅发生重要的作用,让拉斯蒂涅再一次受到了资产阶级自私自利

巴尔扎克作品中的现实主义风格

龙源期刊网 https://www.360docs.net/doc/3814183669.html, 巴尔扎克作品中的现实主义风格 作者:梁萧 来源:《现代交际》2016年第01期 摘要:法国文学巨匠巴尔扎克的作品充满了批判现实主义色彩,以写实为基调,成为19 世纪法国社会的一面镜子。他善于在特定环境下塑造典型的、具有代表性的、富有个性化的人物;再通过人物再现的写作手法,折射社会,堪称现实主义写作风格的代表作家之一。他所描绘的现实世界,并非是生活的复制品,而是基于小说家敏锐的观察力,用小说写作手法呈现“真实”的世界。可以说,他是一位创造现实的现实主义作家。 关键词:巴尔扎克;现实主义;写实 中图分类号:G6343文献标识码:A文章编号:1009-5349(2016)01-0140-05 作为现实主义小说的奠基人,巴尔扎克不仅开辟了小说的新天地,更将小说的表现力提升到空前的高度。他强调塑造人物要典型化,从典型化中突出人物个性,再通过典型人物这一个“点”去折射社会现实的一个“面”。他所刻画的人物如“伏脱冷”、高老头的女儿,将个性与共性完美结合,又展现得淋漓尽致,使之成为典型的小说人物。他的作品反映社会现实,以写实为基调,长于描写丰富多彩的生活,刻画的法国社会风俗细致入微,读者通过人物命运的变化,看到了19世纪法国社会所经历的巨变。他通过创造现实来描写“真实”世界的创作模式,被誉为“创造现实的现实主义者”。 一、还原巴尔扎克 巴尔扎克作为现实主义文学巨匠,是塑造典型小说人物的大师。在其二十载的创作生涯中,创作了《高老头》、欧也妮·葛朗台》《幽谷百合》等脍炙人口的不朽之作,而《人间戏剧》更是被誉为“法国社会的百科全书”,真实地呈现了19世纪法国社会中金钱的统治地位,深刻剖析了人性的丑与美,在世界小说史上树立了一块迄今为止仍无法超越的丰碑。[1]与他 同时代的法国文学巨匠维克多·雨果在其葬礼上发表了这样的赞誉:“在最伟大的人物中间,巴尔扎克是第一等的人;在最优秀的人物中间,巴尔扎克是最高的一个。”[2] 尽管巴尔扎克在生前并未得到应有的赞誉,但在其死后,人们逐渐认识到他作品的伟大之处,并将其誉为“现实主义”小说的奠基人。在今天,我们重读巴尔扎克作品时,不禁被其光怪陆离的小说场景、极富个性的人物形象、对现实世界中追逐金钱名利心理的深刻剖析所折服。他的作品兼具了现实主义小说的三大特性,即真实的细节描写、典型的人物形象、客观的叙述方式。要解读巴尔扎克作品,剖析他是如何创作出如此“真实”的小说,首先要还原巴尔扎克,还原他的创作历程。 (一)折射社会的镜子

第二制冷剂量热器法

. 第二制冷剂量热器法 本实验采用国标(GB 5773-04)提出的对容积式制冷压缩机性能测试的主要试验方法──第二制冷剂量热法,对制冷压缩机的制冷量和输入功率进行测定。根据标准,本试验方法适用于名义功率不小于0.75kW 的容积式制冷压缩机的性能试验。 第二制冷剂量热器法是通过第二制冷剂量热器间接测定制冷量,是利用安置在第二制冷剂量热器内部的电加热管发出的热量来消耗蒸发器盘管所产生的制冷量。 本试验装置有二种制冷剂,其中第一制冷剂为R22,第二制冷剂为R11。第二制冷剂量热器是一个密闭的受压的隔热容器,安置在该量热器内的蒸发器盘管悬挂在容器的上部,电加热管安装在容器的底部并被容器内的第二制冷剂浸没。第一制冷剂在制冷系统中循环,在第二制冷剂量热器的蒸发器盘管中蒸发制冷;输入第二制冷剂量热器的热量主要是电加热管供给(量热器的漏热量应不超过5%),量热器内的第二制冷剂被加热汽化,形成的第二制冷剂蒸汽在顶部蒸发器盘管外表面冷凝,重新回到液面。这样,制冷系统所产生的冷量被输入的热量通过第二制冷剂这中间介质间接消耗,当试验系统的热力状态趋于稳定,表明量热器内趋于动态热平衡。 当系统处于热平衡时,其热平衡方程式为: ( W ) 式中:Q 0── 发器盘管制冷量,W ; N h ── 加热功率,W ; △Q l ── 第二制冷剂量热器的热损失(外界传入为正),W 。 图1 全封闭式制冷压缩机性能试验装置系统图 a 、全封闭式制冷压缩机 b 、冷凝器 c 、节流阀 d 、蒸发器盘管 e 、第二制冷剂量热器 f 、电加热管 g 、静压水箱 h 、第二制冷剂压力表 i 、电功率表 j 、制冷压缩机吸气压力表 k 、制冷压缩机排气压力表 l 、冷凝压力水量调节阀 l h Q N Q ?+=

巴尔扎克的简介

巴尔扎克的简介 巴尔扎克的简介奥诺雷·德·巴尔扎克,法国小说家,被称为现代法国小说之父。生于法国中部图尔城一个中产者家庭。1816年入法律学校学习,毕业后不顾父母反对,毅然走上文学创作道路,但是第一部作品五幕诗体悲剧《克伦威尔》却完全失败。尔后他与人合作从事滑稽小说和神怪小说的创作,曾一度弃文从商和经营企业,出版名著丛书等,均告失败。商业和企业上的失败使他债台高筑,拖累终身,但也为他日后创作打下了厚实的生活基础。1829年发表长篇小说《朱安党人》,迈出了现实主义创作的第一步。1831年出版的《驴皮记》使他声名大震。他要使自己成为文学事业上的拿破仑,在30至40年代以惊人的毅力创作了大量作品。一生创作甚丰,写出了91部小说,合称《人间喜剧》。但由于早期的债务和写作的艰辛,终因劳累过度于1850年8月18日与世长辞。 巴尔扎克的生平人物档案 早年 出生 1799.5.20 寄养 1803-1807 效区列盖公寓 小学 1807-1813 旺多姆教会学校 中学 1814-181 5 黎毕德拉学校 大学 1815-1819 巴黎法律专科学校

青年 初试文学 1819-1825 流行小说写作 从事实业 1825-1828 从事实业,负债累累 文坛新秀 1828-1835 日渐成熟,形成自己风格 晚年 文坛宿将 1835-1850 创作高潮 文学家协会委员时期 1839-1850[1] 生平概述 100多年来,他的作品传遍了全世界,对世界文学的发展和人类进步产生了巨大的影响。马克思、恩格斯称赞他“是超群的小说家”、“现实主义大师”。 巴尔扎克法科学校毕业后,拒绝家庭为他选择的受人尊敬的法律职业,而立志当文学家。为了获得独立生活和从事创作的物质保障,他曾试笔并插足商业,从事出版印刷业,但都以破产告终。这一切都为他认识社会、描写社会提供了极为珍贵的第一手材料。他不断追求和探索,对哲学、经济学、历史、自然科学、神学等领域进行了深入研究,积累了极为广博的知识。 1829年,巴尔扎克完成长篇小说《朱安党人》,巴尔扎克将《朱安党人》和计划要写的136部小说总命名为《人间喜剧》,并为之写了《前言》,阐述了他的现实主义创作方法和基本原则,从理论上为法国批判现实主义文学奠定了坚固的基础。巴尔扎克在艺术上取得巨大成就,他在小说结构方面匠心独运,小说结构多种多样,不拘一格、并善于将集中概括与精确描摹相结合,以外形反映内心本质等手法来塑造人物,他还善于以精细人微、生动逼真

制冷原理与装置二思考题(带答案-排版)

制冷原理与装置二思考题 第一章 1 制冷与空调装置由几部分组成?试举例说明。 答:P1制冷与空调装置是将制冷设备和耗冷设备组合在一起的装置。它除了制冷主机、辅机及由连接管道组成的制冷系统外,还包括与建筑、结构相适应的给水排水、采暖通风、机械传送、电力照明及自动控制等系统。举例说明:空调制冷装置由制冷、冷风或冷水系统等组成。 2 制冷与空调装置中可以利用的新能源有哪些?试举一例,说明其结构组成和工作原理。 答:P2可以采用的新能源:风能、海洋能、太阳能等。举例说明:太阳能(吸附式制冷): 所谓太阳能制冷,就是利用太阳集热器为吸收式制冷机提供其发生器所需要的热媒水。热媒水的温度越高,则制冷机的性能系数(亦称COP)越高,这样空调系统的制冷效率也越高。太阳能吸收式空调系统主要由太阳集热器和吸收式制冷机两部分构成;吸收式制冷机主要由发生器、冷凝器、蒸发器和吸收器组成。吸收式制冷是利用两种物质所组成的二元溶液作为工质来进行的,这两种物质在同一压强下有不同的沸点,其中高沸点的组分称为吸收剂,低沸点的组分称为制冷剂。当溴化锂水溶液在发生器内受到热媒水加热后,溶液中的水不断汽化;水蒸气进入冷凝器,被冷却水降温后凝结;随着水的不断汽化,发生器内的溶液浓度不断升高,进入吸收器;当冷凝器内的水通过节流阀进入蒸发器时,急速膨胀而汽化,并在汽化过程中大量吸收蒸发器内冷媒水的热量,从而达到降温制冷的目的;在此过程中,低温水蒸气进入吸收器,被吸收器内的浓溴化锂溶液吸收,溶液浓度逐步降低,由溶液泵送回发生器,完成整个循环。 3 何谓冷藏链?组成食品冷藏的主要环节有哪些? 答:P2冷藏链是指食品从产地进行冷加工后冷藏运输至冷藏库贮存,然后通过冷藏销售柜由市场进入家用冰箱。 组成环节:采集、加工、冷冻、运输、贮藏、零售到消费者等环节。 第四章 1简述食品低温贮藏和气调贮藏保鲜的基本原理。 答:P39食品低温贮藏基本原理:微生物的生长繁殖需要一定的温度水分,微生物正常活动的温度范围为0-80℃,高温或低温都可以抑制或终止微生物的繁殖,甚至灭菌上述温度效果同样适用于酶。因此,用人工制冷的方法降低食品的温度或使食品冻结,就能有效地控制微生物和酶的作用,保证食品长期存放而不变质。 P42气调贮藏保鲜原理:在冷藏的基础上,进一步提高贮藏温度的相对湿度,并人为地造成某种特定的气体成分,在维持水果正常生命活动的前提下,有效地抑制呼吸、蒸发、激素、微生物和酶的作用,延缓其生理代谢,推迟后熟衰老进程和防止变质腐败,使水果更长久的保持新鲜和优质的食用状态,这就是气调贮藏原理。 2 气调贮藏的主要方式有哪些?通常需要控制哪几项气调指标? 答:P43气调贮藏的方式:快速气调、自然气调、减压气调等等。控制指标:温度、相对湿度、气体成分(氧气、二氧化碳浓度)、贮藏期。 3 冷库制冷系统中,氨系统和氟系统各有何特点? 答:P55~P57氨、氟系统各自主要特点和适用范围: 氨系统:大中型(1000~10000t)系统;采用水冷效率较高;周边没有大片居民区(一旦泄漏有毒害危险);配合土建库较多;建设周期较长;系统有人值守(较少设计成自控系统);操作维修需要一定专业知识;调配相对灵活…… 氟系统:中小型系统、组合快装式;(尤以小型冷库更为普遍采用);在没有条件采用水冷的地方,风冷可以满足要求;无毒害;小型机组多有成套产品,安装快捷;多为自动控制;维修率低; 总体运行费用大中型氨系统稍好一些,但缘于大型、水冷等多方面因素,不可简单对比。 4 何谓间接制冷系统和直接制冷系统?有何特点? 答:P55 直接冷却即利用制冷剂的蒸发来直接冷却被冷却物体,冷冻加工和冷藏一般都采用这种方式。而间接冷却是指通过中间介质,将被冷却物体的热量传送给制冷剂,盐水制冰就是典型的例子。 直接冷却系统是制冷剂直接在冷却设备内蒸发吸热,它不需要其他媒介传递热量,具有传热效果好,设备和管理简单,适应各种冷库使用。 间接冷却好处:可以减少制冷系统的容积而减少制冷剂的充注量,由于载冷剂的热容量较大,被冷却对象的温度易于保持恒定。系统万一泄露,食品不会被制冷剂污染。 间接冷却缺点:系统因增加中间介质的冷却和输送装置而变的更为复杂,投资和能耗相应增大。 5 与普通冷库相比,气调库制冷系统有哪些特点? 答:P66气调库的制冷系统与高温冷藏库基本相同。由于气调贮藏的特殊性,故其制冷系统的设置要注意以下问题:(1)制冷设备的配置,应考虑其冷负荷与冷藏库的不同。 (2)气调库入库阶段的负荷与贮藏阶段的负荷相差很大,采用配有双速风机的冷风机尤为重要,既可以使入库的果蔬很快冷却下来,又能减少果蔬在贮藏中的干耗。

巴尔扎克资料

巴尔扎克兄弟姐妹共四人(父亲在外又有几个非婚生孩子),母亲宠爱的弟弟是母亲瞒着父亲与他人的私生子。他从小怕母亲,回忆童年时曾说一听到母亲的声音便会吓一大跳,成年后更感到生母的贪婪和冷酷。他有一次破产欠了6万法郎,其中4万的债主便是母亲,长期不还时也始终拒绝勾销。无妻小的巴尔扎克常外出游荡,只好把留在巴黎的房产财物交给唯一可信的老娘管理,结果被做了些小手脚,使得母子反目。有暴发户特点的布尔乔亚式的贪欲、自私、放荡,充分显现在这个家中,无怪他笔下能入木三分地发掘恶习、解剖情欲。 巴尔扎克一生放荡不羁,经常挥霍无度和负债破产,爱情婚姻又十分复杂。他早期想娶阔家小姐却被人看不上,出名后又成为不少有闲贵妇追逐和消遣的对象。他在理发店剪下的发屑,有时竟然成为一些少妇和太太的争夺品。他曾痴情于逢场作戏的侯爵夫人而遭耍弄,23岁至33岁时与比自己母亲年纪还大的一位夫人成了长期情人。后来他十几年追求自己作品的崇拜者、一位拥有4万佃农的俄国贵族庄园太太,两人还生过一个孩子(可惜夭折)。这个伯爵夫人丧夫后却因门第之见,拖了八年不肯结婚。直至作家去世三个月前,寒斯卡夫人出于怜悯及其他目的才勉强举行了婚礼,不久又有了新情人。巴尔扎克长期卧床带着周身恶臭病逝时,仅有妹妹、妹夫看望,床边守护的只是感情不睦却毕竟血肉相连的母亲。 “伟人的一生势必不幸”。巴尔扎克这句自诩的话,也是其生平的写照。他个人经历颇受非议,然而这个生活凡人却是思想巨人,留下的作品成为警世的不朽艺术篇章。 。《巴尔扎克传》从巴尔扎克的童年生活入笔,既记述了他在成功前的种种努力,奇异的幻想和追求,令世人咋舌的传奇,又记述了他成名后与同时代名人、朋友、家庭的交往及他的写作生活,使多侧面的巴尔扎克——他的痛苦与欢乐,他的天才和刻苦,他伟大的人性力量,都一一展现出来。传记还充分揭示了巴尔扎克个性中鲜为人知的冒险因素,从而为他的笔锋直入法国社会提供了有力的佐证。传记中巴尔扎克身后的背景如同他的伟大作品中所展现的,是一部丰富多彩的法国历史 巴尔扎克童年所渴望得到的,就是这种母性的爱抚,然而他自己的母亲却拒绝给予他。他一直在苦苦追寻,而竟在此时却得到了他早想获得 的东西。他就是要这样一个能负保护之责的天使般的女人,让他自觉到他身体里的蕴含着的力量如何排泄出来:一个既爱他而又是他知已的人来解除他内心的紧张;把他纤维中粗糙的部分提取出来但又不伤及他的身体;既能鼓励他,同时又以一种合作者的态度指出其缺点,但决不是恶意地批评;尽力了解他的思想,但对他丰富多彩的梦想并不加以嘲弄。他迫不及待地要把他的内心思想感情坦露出来让别人知道。这个年纪与他母亲相仿的人,在听他倾诉时,给他留下的是值得信赖的感觉;当他谈到他那些众多的、充满了幻想的计划时,她的明朗而且聪慧的双眼温和地闪耀着。就是这个女人,她用她的温柔与和善,把他那由于粗俗和缺乏自控力而造成的神经质矫正过来。经过她温柔小心地调教,经过她的熏陶和教育,便使他已失掉的自信力重新恢复了。在他的《费米安尼夫人》一书中,描写到他们两人的接触而给他带来的幸福: 尔扎克所闯进的是一种特殊而又新颖的氛围。跟这个家庭的交往,竟 给这位年青的巴尔扎克一个机会去体验当代历史上的真正精神,他原本对民众及其时代的关系有着深厚的感情 司汤达

第二章制冷剂、载冷剂、冷冻机油1

第二章制冷剂载冷剂冷冻机油 目的:通过对制冷剂、载冷剂、冷冻机油的了解;正确使用制冷剂、载冷剂、冷冻机油。 第一节制冷剂 1,什么是制冷剂以及制冷剂的作用: 制冷剂:就是在制冷系统中能够循环变化的物质,也叫工质。 制冷过程就是制冷剂在循环过程中发生相变时(蒸 发或冷凝)吸收或释放热量来达到热量从低温部分转移到高温部分。 2,制冷剂的安全、环境特性 毒性危害分类:分A、B两类。A类,无毒性或低毒性;B类,高毒性。 燃烧性危害程度分类:分1、2、3类。分别为:不可燃、有燃烧性、有爆炸性。 臭氧消耗潜能值ODP:表示制冷剂消耗大气臭氧分子潜能的程度。 选用R11的值作为标准值1.0。 温室效应潜能值(全球变暖潜能值)GWP:是衡量制 冷剂对气候变暖的影响值。选用二氧化碳的温室效应潜能值为标准值1.0。 例:毒性危害和燃烧性危害程度分类 ODP GWP R11 A1 1.0 4600 R12 A1 0.82 10600 R744(CO2) A1 0 1 R717(氨) B2 0 1 R22 A1 0.034 1900 R134a A1 0 1600 3,常用制冷剂 1)氨(NH3 R717) 标准沸点-33.4℃,凝固温度-77.7℃。有较好的热力性质和热物理性质; 压力适中,单位容积制冷量大,粘性小,流动阻力小,比重小,传热性能好; 价格便宜、易获得。 毒性大,易燃易爆,有强烈刺激性气味,对食品易产 生污染; 空气中氨的容积浓度达到0.5~0.6%时,人在其中停 留半小时就会引起中毒; 容积浓度达到11~14%时,可以燃烧; 容积浓度达到16~25%时,遇明火可以引起爆炸; 氨在高温(260℃)时会分解出氢气(H2),遇空气 及明火会产生强烈的爆炸; 氨系统必须安装空气分离器,及时排放系统中的空 气及其它不凝性气体。 氨极易溶于水,可以与水以任意比例互溶,因此在 氨系统中不会产生冰塞,可以不加干燥过滤器;但有水存在,极易腐蚀金属,并提高蒸发温度;纯氨不腐蚀钢、铁,但含水时会腐蚀锌、铜及铜合金(除磷青铜),因此在氨制冷机及系统中不允许使用铜及铜合金部件(包括压力表,氨压力表必须标有“氨”字样),只有个别起耐磨、密封的部件才可以使用高锡磷青铜,如活塞机的小头衬套和轴封。

巴尔扎克的小说赏析

论巴尔扎克的小说 奥诺雷·德·巴尔扎克,法国小说家,现代法国小说之父,生于法国中部图尔城一个中产者家庭,1816年入法律学校学习,毕业后毅然走上文学创作道路,但是第一部作品五幕诗体悲剧《克伦威尔》却完全失败。曾一度弃文从商和经营企业,出版名著丛书等,均告失败。商业和企业上的失败使他债台高筑,拖累终身,但也为他日后创作打下了厚实的生活基础。1829年,他发表长篇小说《朱安党人》,迈出了现实主义创作的第一步,1831年出版的《驴皮记》使他声名大震。他要使自己成为文学事业上的拿破仑,在30至40年代以惊人的毅力创作了大量作品,一生创作甚丰,写出了91部小说,合称《人间喜剧》。《人间喜剧》被誉为“资本主义社会的百科全书”。但他由于早期的债务和写作的艰辛,终因劳累过度于1850年8月18日与世长辞。他的小说善于描写细节,精细入微,生动逼真;成功塑造典型环境中的典型人物;人物形象生动、充满个性。其作品具有巨大的艺术力量,是法国现实批判主义的最高峰。 一百多年来,他的作品传遍了全世界,对世界文学的发展和人类进步产生了巨大的影响。巴尔扎克在世界文学史上的地位早已确定无疑了,这主要是由他的长篇小说取得的伟大成就所奠定的。但是,综观他的创作,不能不看到他的中篇和短篇小说也起着举足轻重的作用,它们组成了他的鸿篇巨制《人间喜剧》不可或缺的一部分,其中不少是翘楚之作,堪称世界中短篇小说中的精品。巴尔扎克在法国中短篇小说发展史上所起的作用是巨大的。19世纪初,法国中短篇小说正处于发展的转折期。在此之前,中短篇小说应该说还处于萌芽状态,尽管已有不少著名的作品问世。从16世纪开始,玛格丽特·纳瓦尔的《七日谈》、德·拉法耶特夫人的《克莱夫王妃》、伏尔泰(1694—1778)的哲理小说《老实人》、《天真汉》、《查第格》、《如此世界》,狄德罗的《两个朋友》和《众口铄金》,萨德侯爵(1760一1814)的《爱情的策略》等,在中短篇小说的发展史上都是不可不提的作品。可是,无论从人物形象的塑造还是结构方面来说,法国中短篇小说在19世纪之前还没有臻于成熟,就短篇而言,只能说这些作家写的是故事,而并非是真正的短篇小说。也许,法国的中短篇小说要从夏多布里昂的《阿达拉》和《勒内》开始。尤其是《勒内》,塑造了所谓“世纪病”的典型——勒内。这

03第2章制冷剂-1

第二章 制冷剂与载冷剂 第一节 制冷剂 制冷剂是制冷装置中进行循环制冷的工作物质,又称为“工质”。 一、对制冷剂的基本要求 (一)热力学性质 (二)物理化学性质 (三)环境友好性能 反映一种制冷剂环境友好性能的参数有消耗臭氧层潜值(Ozone Depletion Potential, ODP )、全球变暖潜值(Global Warming Potential, GWP )、大气寿命(排放到大气层的制冷剂被分解一半时所需要的时间,Atmospheric Life )等。 变暖影响总当量TEWI (Total Equivalent Warming Impact )综合考虑了制冷剂对全球变暖的直接效应DE 和制冷机消耗能源而排放的CO 2对全球变暖的间接效应IE [3]。 IE DE TEWI += (2-1) 其中,)(α?+??=M N L GWP DE b E N IE ??= 综合考虑制冷剂的ODP 、GWP 和大气寿命,当其排放到大气层后对环境的影响符合国际认可条件时,则认为是环境友好制冷剂。评价制冷机使用制冷剂的环境友好性能时,国际认可的条件如下[8][9]: [3] 日本冷凍空調学会 編. 上級標準テキスト·冷凍空調技術(冷凍編)[M],社団法人日本冷凍空調学会,2000年7月. [8] GB/T 7778-2008, 制冷剂编号方法和安全性分类[S]. [9] LEED. LEED for New Construction Version 2.2, EA Credit 4: Enhanced Refrigerant Management [M]. October, 2005.(美国绿色建筑协会. LEED-NC 标准2.2版,第四评分项《加强制冷剂管理》,2005年10月) 沸点(℃) 单位容积制冷能力(k J /m 3) 图2-1 制冷剂的单位容积制冷能力与沸点的关系

相关文档
最新文档