MAX1798EGP+;MAX1798EGP+T;中文规格书,Datasheet资料
For pricing, delivery, and ordering information,please contact Maxim Direct at 1-888-629-4642,or visit Maxim’s website at https://www.360docs.net/doc/52703191.html,.
General Description
The MAX1798/MAX1798A/MAX1799/MAX1799A system power supplies are designed specifically for CDMA cel-lular/PCS handsets. Each device contains five low-dropout linear regulators (LDOs), a 140ms (min) reset timer, a serial interface, push-on/push-off control logic,and two general-purpose open-drain outputs. Only the serial interface is different between the MAX1798/MAX1798A/MAX1799/MAX1799A: the MAX1798/MAX1798A feature an SPI?-compatible serial interface,and the MAX1799/MAX1799A feature an I 2C-compati-ble interface. The “A” parts have a -13% reset thresh-old, the non-A parts have a 9.5% threshold. The “A”parts have a 175 delay on a reset-triggered shutdown,the non-A shutdown instantly.
Each linear regulator features extremely low dropout voltage, specified at two-thirds of the maximum output current. LDO1 is rated for 300mA, while LDOs 2–5 are each rated for 150mA. All LDOs are optimized for low noise and isolation. Each LDO can be individually enabled and disabled through the serial port, as well as individually programmed to any of 32 voltages from 1.8V to 3.3V.
The MAX1798/MAX1798A/MAX1799/MAX1799As’wide 2.5V to 5.5V input voltage range makes them compati-ble with a wide range of input supplies, including a sin-gle lithium-ion (Li+) cell battery. Both devices are available in thermally-enhanced 20-pin TSSOP and TQF N exposed pad (EP) packages. Evaluation kits in TSSOP (MAX1798EVKIT and MAX1799EVKIT) are avail-able to facilitate designs.
Features
o One 300mA Low-Noise LDO o Four 150mA Low-Noise LDOs o 45μV RMS Noise from 10Hz to 100kHz o >60dB Crosstalk Isolation Below 10kHz o >60dB PSRR Below 10kHz
o 125mV (max) Dropout (OUT1 at 200mA)o 100mV (max) Dropout (OUT2–5 at 100mA)o Programmable Output Voltages
1.8V to 3.3V in 32 Steps o 140ms (min) Reset Timer
o SPI- or I 2C-Compatible Serial Interface o Push-On/Push-Off Control Logic
o Two 150mA General Purpose Open-Drain Outputs o Overcurrent and Thermal Protection (all LDOs)o 1μA Shutdown Current
o 20-Pin Thermally-Enhanced TSSOP or TQFN Packages
Applications
CDMA Cellular/PCS Handsets
PDAs, Palmtops, and Handy-Terminals Single-Cell Li+ Systems
2- or 3-Cell NiMH, NiCd, or Alkaline Systems
MAX1798/MAX1798A/MAX1799/MAX1799A
CDMA Cellular/PCS System
Power Supplies
________________________________________________________________Maxim Integrated Products
1
SPI is a trademark of Motorola, Inc.
Ordering Information continued and Pin Configurations appear at end of data sheet.
Typical Operating Circuit
Ordering Information
+Denotes a lead(Pb)-free/RoHS-compliant package.*EP = Exposed pad.
M A X 1798/M A X 1798A /M A X 1799/M A X 1799A
CDMA Cellular/PCS System Power Supplies 2_______________________________________________________________________________________
ABSOLUTE MAXIMUM RATINGS
-ELECTRICAL CHARACTERISTICS
(V IN1= V IN2/3= V IN4/5= V SCLK (SCK)= V DIN (SDA)= V CS (AS)= V OFF = 3.6V; ON = GND = PGND = 0; RSO, ONO, DR1, DR2 =open; BP bypassed with 0.01μF, OUT1 bypassed with 4.7μF; OUT2, OUT3, OUT4, OUT5 bypassed with 2.2μF; OUT1–5 set to 2.98V,T A = 0°C to +85°C , unless otherwise noted. Typical values are at T A = +25°C.)
Stresses beyond those listed under “Absolute Maximum Ratings” may cause permanent damage to the device. These are stress ratings only, and functional operation of the device at these or any other conditions beyond those indicated in the operational sections of the specifications is not implied. Exposure to absolute maximum rating conditions for extended periods may affect device reliability.
OFF , DR1, DR2 to GND............................................-0.3V to +6V IN1, IN2/3, IN4/5, DIN (SDA) to GND.......................-0.3V to +6V SCLK (SCK), BP, ON to GND...................................-0.3V to +6V RSO , ONO to GND.................................-0.3V to (V OUT1+ 0.3V)PGND to GND.....................................................................±0.3V OUT1, CS (AS) to GND..............................-0.3V to (V IN1+ 0.3V)OUT2, OUT3 to GND...............................-0.3V to (V IN2/3+ 0.3V)OUT4, OUT5 to GND...............................-0.3V to (V IN4/5+ 0.3V)Continuous Sink Current
DR1, DR2...............................................................100mA RMS
RSO ................................................................................25mA Continuous Power Dissipation (T A = +70°C)
20-Pin TQFN (derate 33.8mW/°C above +70°C)...............2W 20-Pin TSSOP (derate 37.7mW/°C above +70°C).............2W Operating Temperature Range ...........................-40°C to +85°C Junction Temperature......................................................+150°C Storage Temperature Range.............................-65°C to +150°C Lead Temperature (soldering, 10s).................................+300°C Soldering Temperature (reflow).......................................+260°C
ELECTRICAL CHARACTERISTICS (continued)
MAX1798/MAX1798A/MAX1799/MAX1799A CDMA Cellular/PCS System Power Supplies (V IN1= V IN2/3= V IN4/5= V SCLK (SCK)= V DIN (SDA)= V CS(AS)= V OFF= 3.6V; ON= GND = PGND = 0; RSO, ONO, DR1, DR2 = open; BP bypassed with 0.01μF, OUT1 bypassed with 4.7μF; OUT2, OUT3, OUT4, OUT5 bypassed with 2.2μF; OUT1–5 set to 2.98V,
T A= 0°C to +85°C, unless otherwise noted. Typical values are at T A= +25°C.)
M A X 1798/M A X 1798A /M A X 1799/M A X 1799A
CDMA Cellular/PCS System Power Supplies 4_______________________________________________________________________________________
ELECTRICAL CHARACTERISTICS (continued)
(V IN1= V IN2/3= V IN4/5= V SCLK (SCK)= V DIN (SDA)= V CS (AS)= V OFF = 3.6V; ON = GND = PGND = 0; RSO, ONO, DR1, DR2 =open; BP bypassed with 0.01μF, OUT1 bypassed with 4.7μF; OUT2, OUT3, OUT4, OUT5 bypassed with 2.2μF; OUT1–5 set to 2.98V,T A = 0°C to +85°C , unless otherwise noted. Typical values are at T A = +25°C.)
ELECTRICAL CHARACTERISTICS
MAX1798/MAX1798A/MAX1799/MAX1799A CDMA Cellular/PCS System Power Supplies (V IN1= V IN2/3= V IN4/5= V SCLK (SCK)= V DIN (SDA)= V CS(AS)= V OFF= 3.6V; ON= GND = PGND = 0; RSO, ONO, DR1, DR2 = open; BP bypassed with 0.01μF, OUT1 bypassed with 4.7μF; OUT2, OUT3, OUT4, OUT5 bypassed with 2.2μF; OUT1–5 set to 2.98V,
T A= -40°C to +85°C,unless otherwise noted.) (Note 2)
CDMA Cellular/PCS System Power Supplies 6_______________________________________________________________________________________
ELECTRICAL CHARACTERISTICS (continued)
(V IN1= V IN2/3= V IN4/5= V SCLK (SCK)= V DIN (SDA)= V CS (AS)= V OFF = 3.6V; ON = GND = PGND = 0; RSO, ONO, DR1, DR2 =open; BP bypassed with 0.01μF, OUT1 bypassed with 4.7μF; OUT2, OUT3, OUT4, OUT5 bypassed with 2.2μF; OUT1–5 set to 2.98V,T A = -40°C to +85°C ,unless otherwise noted.) (Note 2)
M A X 1798/M A X 1798A /M A X 1799/M A X 1799A
MAX1798/MAX1798A/MAX1799/MAX1799A
CDMA Cellular/PCS System
Power Supplies
_______________________________________________________________________________________7
Note 1:The dropout voltage is defined as (V IN - V OUT ) when V OUT is 100mV below the value of V OUT for V IN = V OUT + 1V.Note 2:Specifications to -40°C are guaranteed by design, not production tested.
Note 3:Specifications are guaranteed by design, not production tested in the ETP (TQFN) packages.
ELECTRICAL CHARACTERISTICS (continued)
(V IN1= V IN2/3= V IN4/5= V SCLK (SCK)= V DIN (SDA)= V CS (AS)= V OFF = 3.6V; ON = GND = PGND = 0; RSO, ONO, DR1, DR2 =open; BP bypassed with 0.01μF, OUT1 bypassed with 4.7μF; OUT2, OUT3, OUT4, OUT5 bypassed with 2.2μF; OUT1–5 set to 2.98V,T A = -40°C to +85°C ,unless otherwise noted.) (Note 2)
OUTPUT VOLTAGE ACCURACY (OUT1)
vs. LOAD CURRENT
-2.0
-1.0-1.50-0.51.51.00.52.00
100
50
150200250300LOAD CURRENT (mA)A C C U R A C Y (%)
OUTPUT VOLTAGE ACCURACY (OUT2–5)
vs. LOAD CURRENT
-2.0
-1.0-1.50-0.51.51.00.52.00502575100125150LOAD CURRENT (mA)A C C U R A C Y (%)
-2.0
-1.0-1.50-0.51.51.00.52.0
-4010-15356085
OUTPUT VOLTAGE ACCURACY (OUT1)
vs. TEMPERATURE
TEMPERATURE (°C)
A C C U R A C Y (%)
Typical Operating Characteristics
(T A = +25°C, unless otherwise noted.)
M A X 1798/M A X 1798A /M A X 1799/M A X 1799A
CDMA Cellular/PCS System Power Supplies 8_______________________________________________________________________________________
1
10
100
1000
OUTPUT NOISE vs. LOAD CURRENT
LOAD CURRENT (mA)
O U
T P U T N O I S E (μV R M S )
600
1020304050100μs/div OUTPUT NOISE
V OUT , 50μV/div
700.1
10100
1
1000
CHANNEL-TO-CHANNEL ISOLATION
vs. FREQUENCY
FREQUENCY (kHz)
C H A N N E L -T O -C H A N N E L I S O L A T I O N (d B )
102030405060100
130120110140150160170180190
2000
10050150200250300GROUND-PIN CURRENT (OUT1)
vs. LOAD CURRENT
LOAD CURRENT (mA)G R O U N D -P I N C U R R E N T (μA )
100502001503503002504002.0 3.02.5 3.5 4.0 4.5 5.0 5.5GROUND-PIN CURRENT (OUT1) vs. SUPPLY VOLTAGE (V IN1)
SUPPLY VOLTAGE (V)G R O U N D -P I N C U R R E N T (μ
A )
140
160150180170190200-40103560-1585
GROUND-PIN CURRENT (OUT1)
vs. TEMPERATURE
TEMPERATURE (°C)
G R O U N D -P I N C U R R E N T (μA )
05025100751251500
100
150
50
200
250300
DROPOUT VOLTAGE (OUT1)
vs. LOAD CURRENT
LOAD CURRENT (mA)D R O P O U T V O L T A G E (m V )
50
25100751251500
50
75
25
100
125
150
DROPOUT VOLTAGE (OUT2–5)
vs. LOAD CURRENT
LOAD CURRENT (mA)
D R O P O U T V O L T A G
E (m V )
0.01
0.1
1
10
100
1000
POWER-SUPPLY REJECTION RATIO
vs. FREQUENCY
FREQUENCY (kHz)
Typical Operating Characteristics (continued)
(T A = +25°C, unless otherwise noted.)
MAX1798/MAX1798A/MAX1799/MAX1799A
CDMA Cellular/PCS System
Power Supplies
_______________________________________________________________________________________
9
20μs/div
LINE-TRANSIENT RESPONSE
O U T A C -C O U P L E D 10m V /d i v
I N 500m V /d i v
2μs/div
LOAD-TRANSIENT RESPONSE
O U T 1A C -
C O U P L E
D 50m V /d i v
L O A D 100m A /d i v V IN1 = 3.5V, V OUT1 = 2.98V
I LOAD = 20mA TO 200mA, OUT2/3/4/5 = OFF
2μs/div
LOAD-TRANSIENT RESPONSE
(NEAR DROPOUT)
O U T 1A C -C O U P L E D 50m V /d i v
L O A D 100m A /d
i v
10ms/div
ENTERING SHUTDOWN
V OUT11V/div
OFF 2V/div I LOAD = 0
40ms/div STARTUP
M A X 1798/99-17
V OUT 2V/div 2V/div RSO 2V/div
TSSOP/TQFN SAFE OPERATING AREA
(POWER DISSIPATION LIMIT)
200
40030060050090080070010002.5
3.5
3.0
4.0
4.5
5.0
5.5
6.0
INPUT VOLTAGE (V)M A X I M U M O U T P U T C U R R E N T (m A )
Typical Operating Characteristics (continued)
(T A = +25°C, unless otherwise noted.)
M A X 1798/M A X 1798A /M A X 1799/M A X 1799A
CDMA Cellular/PCS System Power Supplies
分销商库存信息:
MAXIM
MAX1798EGP+MAX1798EGP+T