船舶英语
floating launch飘浮下水
gravity launch重力下水
grease launch油脂下水
steel ball method of launch钢珠下水
mechaniz launch机械化下水
end launch纵向下水
side launch横向下水
incline launch倾斜下水
jump launch跳跃式下水
dipp launch跌入式下水
two-point support launch两支点下水
up to slipway上排
marine slipway下水重量
launch weight下水重量
launch grease下水油脂
pressure bear layer乘压层
transitional layer过渡层
slid layer滑动层
weight of up to slipway上排重量
lift by the stern尾浮
lift尾浮
fore poppet pressure前支架压力
zone of pivot pressure action前支架压力作用区
way end pressure滑道末端压力
dropp首落
bow drop首落
dipp首沉
tipp尾落
launch poppet下水支架
fore poppet前支架
after poppet后支架
launch beam下水横梁
trigger止滑器
check arrangement制动设施
sub-assembl部件装配
section assembl分段装配
unit assembl分段装配
berth assembl船台装配
unit erection at berth船台装配
sectional method of hull construction分段建造法
block method of hull construction总段建造法
horizontal method of hull construction水平建造法
pyramid method of hull construction塔式建造法
island method of hull construction岛式建造法
upright method of hull section construction正装法
upsidedown method of hull section construction倒装法
sideward method of hull section construction侧装法
join ship sections afloat水上合拢
mould bed胎架
jig胎架
fixed mould bed固定胎架
adjustable mould bed可调胎架
positioner摇摆胎架
tilt jig回转胎架
tilt device回转装置
specialized mould bed专用胎架
bed mould胎板
fabrication platform装焊平台
electromagnetic platform电磁平台
position strip定位马
shore定位马
electromagnetic strip电磁马
jip for fitt-up T-sectionsT型材装焊机
temporary stiffen bar临时加强材
assembly frame假舱壁
sub-assembly船体部件
panel板列
section分段
assembly分段
unit分段
basic section基准分段
join section嵌补分段
flat section平面分段
curved section曲面分段
three-dimensional unit立体分段
two-dimensional unit半立体分段
block总段
complete cross section总段
section assembly flow line分段装配流水线
lay-out for assembl装配划线
sequence of erection and weld装配焊接顺序
plate alignment拼板
position定位
frame r肋骨框架
reference line for assembl装配定位线
seperate method of assembl分离装配法
cell method of assembl放射式装配法
interpolate method of assembl插入装配法
centerline
of berth船台中心线
sight column望广柱
positioner for unit erection at berth船台装配定位器
frame station line on berth船台肋骨线
light target光靶
pre-set焊接反变形
manual loft手工放样
scale loft比例放样
full scale loft实尺放样
longitudinal shrink scale loft纵向缩尺放样
fair光顺
fairness光顺性
deviation from offsets修正值
coincide in three projection planes三面吻合
lay off of hull lines型线放样
mathematical loft数学放样
mathematical lines数学型线
mathematical fair of lines型线数学光顺
sectional curved method剖面线法
least square method最小二乘法
linear programm method线形规划法
variational method变分法
curved surface method曲面法
point by point method of modification逐点修改法
local linear interpolation直尺卡样法
elastic local linear interpolation卡尺回弹法
bend-modify relaxation method弯调松弛法
interpolation point正插点
inversed interpolation point反插点
line of intersect points角点线
line of tangential points切点线
line of centers圆心线
localized fair局部光顺
circular spline圆弧光顺
spline function样条函数
fitt拟合
fitt to curved surface曲面拟合
parametric curve with sle flecnode单拐参数曲线
criterion of fairness光顺判别准则
inflexion preservation保凹凸
recurrent force回弹力
coincident recurrent force正回弹力
incoincident recurrent force返回弹力
recurrent magnitude回弹量
bend direction of curve弯向
chang of curvature弯势
excess flecnode多余拐点
bad point坏点
bad point interval坏点区
discriminat function定改函数
mathematical development of shell plate外板数学展开
equation of frame肋骨方程
equation of longitudinal seam纵缝方程
equation of transverse seam横缝方程
differential geodesic line method微分测地线法
tangential development method切面展开法
thickness modification in plate development板厚修正
shipbuild information data process造船信息数据处理系统
mathematical loft system for pip管路数放系统
graphic data process system图示数据处理系统
line fair program型线光顺程序
seam arrangement program板缝排列程序
shell plate development program外板展开程序
mathematical seam arrangement板缝数学排列
nest program套料程序
structural process program结构处理程序
nest mathematical process套料数学处理
structural mathematical process结构数学处理
tape out-put program纸带输出程序
draw process program绘图处理程序
numerical controlled draw 数控绘图
data treatment and memory program数据处理和存储程序
station No站号
frame No肋骨号
contour line外廓线
shell pate development外板展开
dutum line准线
mean normal method准线展开法
center spot squar method十字线展开法
geodesic line测地线
geodesic line development method测地线展开法
frame section surface肋骨平面
normal plane of shell plate外板法面
trible of buttock lines纵剖线族
tribe of body lines横剖线族
tribe of water lines水线族
camber table梁拱表
frame interpolation肋骨插值
frame body plan肋骨型线图
returned table of offsets完工型值表
finished table of offsets完工型值表
draft mark吃水标志
paint line水线标志
structural member loft结构放样
edge line接口线
upper edge line上口线
lower edge line下口线
seam arrangement板缝排列
longitudinal seam纵向接缝
transverse seam横向接缝
curved surface development曲面展开
structural member development构件展开
curvature of frame肋骨弯度
jig for plate development外板展开器
selected mould section
projected frame line on selected mould section改型肋骨型线
diagonal check methods对角线检查法
sketch for mark off号料草图
template draw样板图
scale draw transparency投影底图
glass negative投影底片
profile draw仿形图
bridge line连割线
template样板
mould样板
mock-up样箱
cradle mould样箱
batten样条
mould bar洋棒
multi-shape template格子样板
adjustable mould可调样板
triangular template三角加工样板
beam mould梁拱样板
frame mould肋骨洋板
section mould加工洋板
template for secondary mark装配划线样板
angular template for assembl装配夹角样板
adjustable angular template可调角度样板
template for mark-off号料样板
loft office放样间
loft floor样台
scale loft table比例放样台
manual mark-off手工号料
mark-off from templates样板号料
mark-off from mould bars样棒号料
mark-off from moulds样箱号料
mark-off from sketches草图号料
secondary mark-off二次号料
nest套料
mark signs号料符号
fram line构架线
automatic mark-off自动号料
projection mark投影号料
projection tower投影塔
projection room投影室
projection mark table投影号料台
positive projection正片投影
negative projection负片投影
image distortion影像畸变
absolute distortion绝对畸变
relative distortion相对畸变
pincushion distortion枕形畸变
barrel distortion桶形畸变
photosensitive mark感光号料
facsimile mark电传真号料
facsimile mark machine电传真号料机
electro-print mark电印号料
electro-print mark apparatus电印号
料装置
synchronized scann projection同步扫描投影
photo-conductive powder光电粉末
electrostatic latent image静电潜像
NCshapes mark machine数控型材号料
pneumatic mark punch风动号料冲头
shipbuild technolgy造船工艺
two-part construction两段造船法
method of build ship in two sections两段造船法
tandem shipbuild method串联造船法
technology of hull construction船体建造工艺
loft放样
mark off号料
hull steel fabrication金属船体加工
assembly and erection船体装配
weld焊接
launch下水
outfitt and machinery installation船舶设备和系统安装
pre-erection outfitt预安装
outfitt and machinery installation on berth船台安装
quay outfitt and installation码头安装
dock outfitt and installation船坞安装
unit outfitt单元安装
unit pre-outfitt单元预装
bollard test系泊实验
sea trial航行实验
construction start date建造开工日
time on build berth船台周期
shipbuild period造船周期
launched displacement of ships下水量
ship output船舶产量
ship delivery交船
operation stage工艺阶段
operation items工艺项目
operational path工艺路线
technological process工艺过程
technological instruction工艺规程
method plann of ship construction原则工艺
standard technological procedure典型工艺
operation items detail chart工艺项目明细表
master schedule总工艺进度表
"positional flow" method流水定位法
"specialized gang" method流水定员法
edge preparation边缘加工
individuals of hull structure船体零件
symbols for hull steel fabrication船体加工符号
groove preparation坡口加工
edge plann刨边
edge mill铣边
edge grind磨边
carbon arc air goug碳弧气刨
plate-edge planer刨边机
plate-edge miller铣边机
shear剪切
roll shear滚剪
blank冲切
mill铣切
scarf削斜
flame cutt火焰切割
plasma cutt等离子切割
arc air cutt电弧气割
gas cutt气割
oxy cutt氧矛切割
oxy-flux cutt氧熔剂切割
laser cutt激光切割
under water cutt水下切割
stack cutt迭板切割
shear squence剪切顺序
drag后拖量
shear machine剪床
guillotine龙门剪床
roll shear machine滚剪机
disk shear圆盘剪
circular shear圆盘剪
nibbl machine振动剪床
shear and punch machine联合冲剪机
semi-automatic gas cutt machine半自动气割机
gantry type semi-automatic gas cutt machine半自动桥式气割机
semi-automatic gas cutt machine for mark circular shape半自动割圆机
semi-automatic multitorch gas cutt machine半自动多炬气割机全位置仿形气割机
all position copy gas cutt machine全位置仿形气割机
automatic gas cutt machine自动气割机
profile gas cutt machi
ne靠模气割机
copy gas cutt machine靠模气割机
photo-electric trac gas cutt machine光电跟踪气割机
photo-electric linefollow gas cutt machine光电跟线气割机
NCgas cutt machine数控气割机
NCuniversal gas cutt machine数控通用气割机
cutt torch割炬
cutt nozzle割嘴
preheat气割预热
roll bend滚弯
press bend压弯
knuckle折角
angle bend less than 90折锐角
angle bend greater than 90折钝角
flang折边
die bend强制弯曲
free bend自由弯曲
concave bend of frame骨材内弯
convex bend of frame骨材外弯
length wise wavws around edge皱折
minimum bend radius最小弯曲半径
pre-bend预弯
surplus straight edge剩余直边
spr back弯曲回弹
rubber mold form橡皮模成型
spinn旋压
flow form旋压
bulg胀形
shot blast form喷丸成型
stretch metal in center portion of sheet放中
tight metal in center portion of sheet收中
stretch metal around edges of sheet放边
tight metal around edges of sheet收边
hammer solidly around edges of sheet拨缘
hogg拱曲
channell压筋
rectification of distortion矫形
rectification of distortion by flame火工矫形
rectification of distortion by flame heat and water cool水火矫形
hot form大火成形
line heat form水火成形
heat line加热线
heated-side cool method正面水冷法
back-side cool method背面水冷法
width of heat affect zone热影响区宽度
length of heat line焰道长度
heat speed热源速度
flame power火焰功率
angular distortion角变形
explosion form爆炸成形
unconfined system explosion form无模爆炸成形
three-roll bend machine三辊弯板机
shipyard roll press造船用滚压两用机
shipyard combined plate bend and flang machine造船用滚压两用机
four-roll bend machine四辊弯板机
press压力机
hydraulic press with adjustable head for ship use造船用压头可移式液压机
three-row plunger type press三排柱塞式弯板机
multi-plunger hydraulic press多柱塞式弯板机
NChydraulic press数控成形液压机
sail-shaped plate帆形板
saddle-shaped plate鞍形板
screw-shaped plate螺形板
corrugated plate波形板
channelled plate槽形板
cylindrical shaped plate桶形板
conical shaped plate锥形板
spherical shaped plate球形板
pure bend纯弯板
concentrated force bend集中力弯曲
stretch bend拉弯
torsional deflection旁弯变形
cold frame bend machine肋骨冷弯机
frame roll machine肋骨滚弯机
frame stretch bend machine肋骨拉弯机
cold frame bend machine with-adjustable die可调模具式肋骨冷弯机
cold frame bend machine with multiplunge
rs多压头式肋骨冷弯机
three cylinder frame bend machine三缸肋骨冷弯机
frame pure-bend machine纯弯曲肋骨冷弯机
frame bend machine of medium frequency induction heat中频肋骨热弯机
NCcold frame bend machine数控肋骨弯曲机
concave bend frame内弯肋骨
convex bend frame 外弯肋骨
s-bend frameS-形肋骨
steel pretreatment刚材预处理
steel levell and straighten钢材矫正
levell of piates钢板矫平
mangle辊式矫平机
plate straightener辊式矫平机
straighten of shapes型钢矫直
shapes straighten machine型钢矫直机
steel preheat钢材预热
rust removal of steel钢材除锈
abrasive blast喷射除锈
abrasive磨料
shot blast抛丸除锈
shot blast machine抛丸除锈机
shot blast room抛丸室
abrasive impeller抛丸器
automatic primer spray自动喷涂底漆
chemical clean化学除锈
acid clean of steel酸洗除锈
pickl酸洗处理
dip pickl浸渍酸洗
spray pickl喷淋酸洗
neutraliz中和处理
passivat钝化处理
phosphat磷化处理
pickl bath酸洗池
pickl waste treatment废酸液处理
acid pickl inhibitor酸洗缓蚀剂
vacu-blast clean真空喷射除锈
arc rust removal电火花除锈
mechanical rust removal机械除锈
secondary rust removal二次除锈
shot peen喷丸除锈
sand blast喷沙除锈
wet sand blast湿喷沙除锈
spray pickl in circulation循环喷射酸洗
acid paste pickl化学膏除锈
hydroblast高压水除锈
flame clean火焰除锈
remote control descal machine遥控除锈机
adjust needle cleaner针束除锈器
stripp film clean可剥性薄膜除锈
section shot-blast分段抛丸除锈
section shot-peen分段喷丸除锈
section pickl分段酸洗除锈
shot-peen room喷丸间
brush paint刷涂
spray pant喷涂
airless spray paint无空气喷涂
electrostatic spray静电喷涂
agent for electrostaic spray静电喷涂助剂
electrocoat电泳涂漆
flow line of pickl酸洗磷化电泳涂漆流水线
phosphat and electrocoat酸洗磷化电泳涂漆流水线
abrasive磨料
abrasive blast喷射除锈
abrasive impeller抛丸器
absolute distortion绝对畸变
acceptance document验收移交书
acceptance of shaft轴系安装验收
acid clean of steel酸洗除锈
acid paste pickl化学膏除锈
acid pickl inhibitor酸洗缓蚀剂
actual throat thickness焊缝厚度
additional test复验
adjustable angular template可调角度样板
adjustable block机械墩
adjustable mould可调样板
adjustable mould bed可调胎架
adjust needle cleaner针束除锈器
after poppet后支架
agent for electrostaic spray静电喷涂助剂
ahead and astern reach measurement惯性试验
air tight test of pipeline管路气密实验
airless spray paint无空气喷涂
alignment找正
alignment by flanges直接找正
ali
gnment of bottom cas and bear seat下气缸和轴承座找正
all position copy gas cutt machine全位置仿形气割机
all position weld全位置焊接
anchor test in trial锚设备效用实验
angle bend greater than 90折钝角
angle bend less than 90折锐角
angular distortion角变形
angular template for assembl装配夹角样板
anneal weld退火焊
approved certificate for product产品合格证
arc air cutt电弧气割
arc blow磁偏吹
arc clean action阴极破碎
arc length弧长
arc rust removal电火花除锈
arc strike引弧
arc weld电弧焊
arcvoltage电弧电压
argon arc weld氩弧焊
assembl error装配误差
assembl on board上船组装
assembly分段
assembly and erection船体装配
assembly frame假舱壁
automatic gas cutt machine自动气割机
automatic primer spray自动喷涂底漆
automatic weld自动焊
automatic weld in vertical position垂直自动焊
auxiliary boiler test辅锅炉试验
average linear load平均线负荷
back chipp清根
back goug清根
back run打底焊
back settl回淤
back weld打底焊
backfire回火
back weld封底焊
bad point坏点
bad point interval坏点区
band test弯曲试验
bank slope驳岸
barrel distortion桶形畸变
base line基准线
base metal母材
basic covered electrode碱性焊条
basic section基准分段
basin港池
batten样条
beam mould梁拱样板
beams gate迭梁式坞门
bear metal cracks轴承龟裂
bed mould胎板
bend direction of curve弯向
bend of pipewith core有芯弯管
bend prior to weld先弯后焊
berth船台
berth assembl船台装配
berth force挤靠力
bevel angle坡口角度
bilge block舭墩
blade rust叶面锈斑
blade tip deflection螺旋桨叶稍上翘
blank冲切
block总段
block load搁顿负荷
block method of hull construction总段建造法
block sequence分段多层焊
blocks墩
blocks with sand box沙箱墩
blowhole气孔
blow吹车
boat tank跳船
boiler burner test锅炉燃烧器试验
boiler water fill上水（锅炉）
bollard test系泊实验
bonded flux陶质焊剂
bonded slag粘渣
bond of plastic pipe塑料管粘接
bond of propeller to shaft螺旋桨胶合联接
bor for shaft line轴系镗孔
bow drop首落
box包角焊
braz钎焊
braz filler metal钎料
braz flux钎剂
break test for anchor chain锚链拉断实验
breakwater防波堤
bridge approach引桥
bridge gauge桥规
bridge line连割线
brush paint刷涂
build berth造船台
build dock造船坞
bulg胀形
burn loss烧损
burn of bear metal白合金烧熔
butt joint对接接头
butt weld对接焊缝
butter预堆边焊
caisson坞门
camber table梁拱表
cambered way弧形滑道
canalled dock运河式船坞
cantilever end load悬臂端负荷
carbon arc air goug碳弧气刨
carbon equivalent炭当量
cargo handl test起重设备负荷试验
cast of propeller in metal patten螺旋桨金属型铸造
cell method of assembl放射式装配法
center block for shaft alig
nment轴系中心定位块
center line strip on berth船台中心线板
center spot squar method十字线展开法
center校中
center of mov parts运动件校中
center of shaft by indicators指针法轴系校中
center of shaft by light光学法轴系校中
center of shaft by ruler and gauge直尺和厚薄规法轴系校中
center of shaft轴系校中
center of shaft by calculation method计算法轴系校中
center of shaft by direct connection平轴法轴系校中
center of shaft by load method轴承负荷法轴系校中
center or rotor转子校中
centerline of berth船台中心线
centrifugal cast of propeller螺旋桨离心铸造
ceramic flux陶质焊剂
chain intermittent fillet weld对称间断焊缝
chang of curvature弯势
channelled plate槽形板
channell压筋
check of axial clearance轴向间隙确定
check of dynamic balance of rotor转子校动平衡
check of play between piston and cylinder cover校气缸余隙
check of propeller pitch螺旋桨螺距校正
check of reference center line中心线测量
check of the tappet clearance校气门间隙
check arrangement制动设施
check of bear clearance with lead压铅法
check of propeller pitch螺旋桨螺距检验
check of surface in contact by mark compound涂色油法
chemical analysis化学分析
chemical clean化学除锈
circular shear圆盘剪
circular spline圆弧光顺
circumferential weld环焊缝
CO2 weld二氧化碳气体保护焊
coat药皮
coincide in three projection planes三面吻合
coincident recurrent force正回弹力
cold bend of pipe管子冷弯
cold crack冷裂缝
cold frame bend machine肋骨冷弯机
cold frame bend machine with multiplungers多压头式肋骨冷弯机
complete cross section总段
complete engine set installation整机安装
complete fusion焊透
compressed air test气压实验
concave bend frame内弯肋骨
concave bend of frame骨材内弯
concentrated force bend集中力弯曲
configuration of bent pipe管子弯势
conical shaped plate锥形板
connection weld联系焊缝
construction start date建造开工日
consumable guide electroslag weld熔嘴电渣焊
consumables焊接材料
continuous weld连续焊缝
continuous weld连续焊
contour line外廓线
convex bend frame 外弯肋骨
convex bend of frame骨材外弯
copper back铜垫
copper shoe铜滑块
copy gas cutt machine靠模气割机
core wire焊芯
core wire diameter焊条直径
coreless bend of pipe无心弯管
corner joint角接接头
corrugated plate波形板
course keep test航向稳定性试验
covered berth室内船台
covered electrode焊条
cover药皮
crack sensitivity焊接裂缝敏感性
crack test抗裂试验
crack test with 500x2000mm test pieces大板对接抗裂试验
cradle mould样箱
crater弧坑
crater crack弧坑裂缝
cribb井字墩
criterion of acceptance of radiographic examination of welded seam焊缝质量射线检查评定标准
criterion of fairness光顺判别准则
cr
iterion of ultrasonic examination of welded seam焊缝超声波探伤标准
cruciform crack test十字接头抗裂试验
cruciform joint十字接头
curvature of frame肋骨弯度
curved section曲面分段
curved surface development曲面展开
curved surface method曲面法
cutt nozzle割嘴
cutt torch割炬
cylindrical shaped plate桶形板
data treatment and memory program数据处理和存储程序
dead center gauge止点规
defective items after inspection废品通知单
deflection of main journal主轴颈下沉量
degree of mechanization in weld焊接机械化程度
deposited metal熔敷金属
deposition rate熔敷系数
depth of fusion熔深
design element of weld焊缝结构要素
design throat thickness焊缝计算厚度
design water lever设计水位
destructive examination破坏性检验
detectaphone侦听起
detection sensitivity探伤仪灵敏度
determination of center line and axis找中
determination of center line or axis找中
determination of shaft linep轴系找中
deviation from offsets修正值
diagonal check methods对角线检查法
dial gauge for measur of crank spread曲轴量表
die bend强制弯曲
differential geodesic line method微分测地线法
diffusible hydrogen content扩散氢含量
dip pickl浸渍酸洗
dip transfer短路过渡
dipp首沉
dipp launch跌入式下水
discriminat function定改函数
disk shear圆盘剪
dock船坞
dock bottom坞底
dock entrance坞口
dock head坞首
dock outfitt and installation船坞安装
dock sill坞坎
dock wall坞壁
dockgate坞门
dockgate channel门槽
dock weight进坞重量
dolphin pier靠船墩
double bevel grooveK型坡口
draft mark吃水标志
drag后拖量
draw process program绘图处理程序
drop test for anchor锚投落试验
dropp首落
dry dock干坞
dry extension of electrode焊丝干伸长
dutum line准线
dynamic characteristic电源动特性
dynamic test of propeller螺旋桨浆动平衡试验
dynamometer测功器
eccentricity偏心度
edge grind磨边
edge joint端接接头
edge line接口线
edge mill铣边
edge plann刨边
edge preparation边缘加工
elastic local linear interpolation卡尺回弹法
electric dynamometer电力测功器
electrocoat电泳涂漆
electrode diameter焊条直径
electrode extension焊丝伸出长度
electrode for vertical down weld下行焊条
electrode negative正接
electrode positive反接
electromagnetic platform电磁平台
electromagnetic strip电磁马
electronbeam weld电子束焊
electronic indicator电子示功器
electroslag weld电渣焊
electroslag weld with plate electrode板极电渣焊
electroslag weld with wire electrode丝极电渣焊
electrostatic latent image静电潜像
electrostatic spray静电喷涂
elevation水位
emergency drain test应急疏水实验
enclosed weld强迫成形焊
end launch纵向下水
equation of frame肋骨方程
equation of longitudinal seam纵缝方程
equation of transverse seam横缝
方程
equilibrium tide平潮
evaluation test of power plant on board动力装置实船鉴定试验
examination of opened up parts拆验
examination of ream紧配螺栓配合检查
excess flecnode多余拐点
excess of water过水
excess weld metal加强高
expander胀管器
explosion expand of pipe爆炸胀管
explosion form爆炸成形
explosive weld爆炸焊接
exposed berth露天船台
external characteristic电源外特性
fabrication platform装焊平台
facsimile mark电传真号料
facsimile mark machine电传真号料机
fair光顺
fairness光顺性
fatigue test疲劳试验
filler metal填充金属
filler wire焊丝
fillet weld角焊缝
fillet weld in flat position船形焊
fillet weld Tee bend testT型接头弯曲试验
fillet weld角焊
final cutt of pipe割管
finished table of offsets完工型值表
firecracker weld躺焊
first product inspection首件检验
FISCO type crack test加压固定对接抗裂试验
fishbone crack test鱼骨型抗裂试验
fitt拟合
fitt of compreg层压胶木镶嵌
fitt of lignumvitae铁梨木镶嵌
fitt of rubber seal r in stern tube尾轴管衬套橡胶嵌套
fitt to curved surface曲面拟合
fixed foot bridge固定引桥
fixed mould bed固定胎架
flame bend of pipe火焰弯管
flame clean火焰除锈
flame cutt火焰切割
flame power火焰功率
flangeless joint无法兰联接
flang折边
flap gate卧倒式坞门
flash back回火
flat position weld平焊
flat section平面分段
flatten test金属管压扁试验
float caisson浮箱式坞门
float launch飘浮下水
float spar fender浮式护木
flood dock注水式船坞
flood test灌水法
flow form旋压
flow line of pickl酸洗磷化电泳涂漆流水线
flow rate of shield gas保护气体流量
flux焊剂
flux back焊剂垫
fog test气雾法
fore poppet前支架
fore poppet pressure前支架压力
formation of weld寒风成形
frame bend machine of medium frequency induction heat中频肋骨热弯机
frame body plan肋骨型线图
frame interpolation肋骨插值
frame lines肋骨检验线
frame mould肋骨洋板
frame No肋骨号
frame r肋骨框架
frame roll machine肋骨滚弯机
frame section surface肋骨平面
frame station line on berth船台肋骨线
frame stretch bend machine肋骨拉弯机
fram line构架线
free bend自由弯曲
free runn空车运转
freeboard measurement of life boat救生艇干舷测定
full penetration焊透
full scale loft实尺放样
fume of weld焊接烟尘
furnace brickwork炉墙砌筑
furnace explosion dur light up冷爆
fused flux熔炼焊剂
gallery廊道
gantry龙门架
gap两轴曲折
gas cutt气割
gas inflation liferaft test气胀式救生筏试验
gas metal arc weld熔化级气体保护焊
gas mixture metal arc weld混合气体保护焊
gas pore气孔
gas tightness气密性
gas tungsten arc weld非熔化级气体保护焊
gas weld气焊
gate chamber门库
gate channel for repair修理门槽
gate pier门墩
g
enerat set portion of bollard test发电机组系泊试验
generat set portion of trial test发电机组航行试验
geodesic line测地线
geodesic line development method测地线展开法
glass negative投影底片
globular transfer大滴过渡
graphic data process system图示数据处理系统
gravity launch重力下水
gravity weld重力焊
grease launch油脂下水
groove坡口
groove angle坡口角度
groove depth坡口深度
groove preparation坡口加工
groove radius坡口半径
guided bend of pipe靠模弯管
guillotine龙门剪床
hammer solidly around edges of sheet拨缘
handl test of life boat救生艇和工作艇降落试验
hard solder钎料
hardness test硬度试验
hardness test of weld zone焊接接头硬度试验
heat affected zone热影响区
heat input线能量
heat line加热线
heat speed热源速度
hell test倾斜试验
high frequency bend of pipe高频弯管
hogg拱曲
horizontal build berth水平船台
horizontal method of hull construction水平建造法
horizontal position weld横焊
hot bend of pipe管子热弯
hot crack热裂缝
hot form大火成形
hot wire submerged arc weld预热焊丝埋弧焊
hull steel fabrication金属船体加工
hydraulic bend of pipe液压弯管
hydraulic dynamometer水力测功器
hydraulic press with adjustable head for ship use造船用压头可移式液压机
hydraulic subassembly for crankshaft曲轴液压套合
hydraulic test of boiler锅炉水压实验
hydraulic test of pipeline管路液压实验
hydroblast高压水除锈
hydrogen content in welds焊缝氢含量
idl惰转
image distortion影像畸变
impact force撞击力
impact test冲击实验
imperfection in bond轴承脱壳
incline launch倾斜下水
inclined build berth倾斜船台
inclined Tee joint斜接接头
incoincident recurrent force返回弹力
incomplete fusion未焊透
indicator示功器
individuals of hull structure船体零件
inflexion preservation保凹凸
insert pipe嵌补管
inspection勘验
inspection of levelness水平度测量
inspection by mould bar样条法检验
inspection by sketch method草图法检验
inspection by templet样板法检验
inspection dur hull steel fabrication船体零部件加工检验
inspection of abutt edges of block总段对接检验
inspection of block总段装配检验
inspection of center line of build berth船台中心线测量
inspection of draft mark and loaded water lines
inspection of frame spac肋骨间距测量
inspection of groove坡口测量
inspection of hull deformation after launch全船校正检查
inspection of hull form after completion船体完工测量
inspection of hull lines线型检验
inspection of hull loft船体放样检验
inspection of install of propeller螺旋桨安装检查
inspection of mould bed胎架检验
inspection of mount of bear seats轴承座安装检验
inspection of panel平面分段检验
inspection of permanent ballast before launch下水压载检查
inspect
ion of preassembled frame r肋骨框架装配检验
inspection of ship structure全船结构检查
inspection of squar accuracy角尺线检查
inspection of three dimensional unit立体分段检验
inspection of thrust block推力块厚度检查
inspection of vertical surface垂直度测量
inspection on development of structural members船体构件展开检验
inspection on shell plate development外板展开检验
installation of boiler锅炉安装
installation of desel engine柴油机安装
installation of main engine主机安装
installation of marine power plant船舶动力装置安装
installation of pip管系安装
installation of pip unit管系单元安装
installation of shaft轴系安装
installation of turbine汽轮机安装
interlayer temperature层间温度
intermittent weld间断焊缝
interpass temperature层间温度
interpolate method of assembl插入装配法
interpolation point正插点
inversed interpolation point反插点
iron powder electrode铁粉焊条
iron wedge楔铁
island method of hull construction岛式建造法
items for acceptance of vessel验收项目
jetty突堤码头
jig胎架
jig for plate development外板展开器
join lines for hull assembly船体装配对合线
join section嵌补分段
join ship sections afloat水上合拢
jump launch跳跃式下水
keel block龙骨墩
knuckle折角
knuckl line slipway折线滑道
lack of fusion未焊透
lagg of boiler锅炉绝热层包扎
lamellar tear层状撕裂
land tie拉桩
lap joint搭接接头
laser alignment激光找正
laser cutt激光切割
launched displacement of ships下水量
launch下水
launch beam下水横梁
launch grease下水油脂
launch poppet下水支架
launch way滑道
launch weight下水重量
layer焊层
lay off of hull lines型线放样
least square method最小二乘法
leg of fillet weld焊脚
length of heat line焰道长度
length wise wavws around edge皱折
levell找平
levell by level gauge液面法找水平
levell of engine bed机座找平
levell of foundation机座找平
levell of piates钢板矫平
lifebuoy test救生圈试验
lift by the stern尾浮
lift尾浮
light target光靶
line fair program型线光顺程序
line heat form水火成形
line of centers圆心线
line of intersect points角点线
line of tangential points切点线
line outs of ship equipments船舶综合放样
linear porosity链状气孔
linear programm method线形规划法
listen侦听
listen rod听音棒
local linear interpolation直尺卡样法
localized fair局部光顺
localized porosity密集气孔
loft放样
loft floor样台
loft office放样间
longitudinal bead bend test纵向焊道弯曲试验
longitudinal bead notched bend test纵向焊道缺口弯曲试验
longitudinal seam纵向接缝
longitudinal shrink scale loft纵向缩尺放样
longitudinal slipway纵向滑道
longitudinal weld纵向焊缝
low pressure cast of propeller螺旋桨低压铸造
lower edge line下口
线
lowest pressure curve of compartments舱室最小压力曲线
magnetic detection磁性探伤
main boiler test主锅炉试验
main engine portion of bollard test主机系泊试验
main engine portion of trial test主机航向实验
mangle辊式矫平机
manipulation of electrode运条方式
manual bend of pipe手工弯管
manual emergency anchor test人力应急起锚试验
manual emergency steer test人力应急操舵试验
manual loft手工放样
manual metal arc weld手弧焊
manual weld手工焊
marginal wharf顺岸码头
marine slipway下水重量
mark for pipes管子划线
mark for shaft bor轴系孔划线
mark off号料
mark signs号料符号
master schedule总工艺进度表
match key on propeller shaft推进器轴配件
mathematical development of shell plate外板数学展开
mathematical fair of lines型线数学光顺
mathematical lines数学型线
mathematical loft数学放样
mathematical loft system for pip管路数放系统
mathematical seam arrangement板缝数学排列
maximum linear load最大线负荷
mean normal method准线展开法
measurement of curvature of frame肋骨弯度测量
measurement of finished propeller螺旋桨完工测量
measurement of fit clearance of propeller螺旋桨配合间隙测量
measurement of fit clearance of shaft轴系安装间隙测量
measurement of fit clearance of sterntube推进器轴安装间隙测量
measur error测量误差
measur of crank spread曲轴臂距差测量
mechanial bend of pipe机械弯管
mechanical blocks机械墩
mechanical expand of pipe机械胀管
mechanical indicator机械示功器
mechanical rust removal机械除锈
mechanized slipway机械化道脂
mechanized weld机械化焊接
mechaniz launch机械化下水
medium frequency bend of pipe中频弯管
melt rate熔化系数
metal transfer熔滴过渡
method of build ship in two sections两段造船法
method plann of ship construction原则工艺
MIG weld熔化级气体保护焊
mill铣切
minimum bend radius最小弯曲半径
moor arrangement test系泊设备实验
moor force系船力
mould样板
mould bar洋棒
mould bed胎架
mount of propeller螺旋桨安装
mount of propeller by hydraulic jack螺旋桨液压无键连接
mount of rotor转子安装
mount of turbine cas气缸合盖
movable foot bridge活动引桥
muff joint套管接头
narrow gap gas metal arc weld窄间隙气体保护焊
negative projection负片投影
nest套料
nest mathematical process套料数学处理
nest program套料程序
neutraliz中和处理
nibbl machine振动剪床
no load runn空车运转
normal plane of shell plate外板法面
notice of acceptance验收通知单
notice on launch of vessel下水通知
numerical controlled bend of pipe数控弯管
numerical controlled draw 数控绘图
numerical controlled flow line for pipe shap管子数控加工自动流水线
oil fog test油雾法
oil test油压试验
oil test of tailshaft sleeve轴套油压试验
oil
tightness油密性
oil tightness test of thrust bear hous推力轴承箱油密检查
one w build berth单翼船台
open circuit voltage空载电压
operation items工艺项目
operation items detail chart工艺项目明细表
operation stage工艺阶段
operational path工艺路线
operative weldability test焊接工艺性试验
optical alignment光学找正
outfitt and machinery installation船舶设备和系统安装
outfitt and machinery installation on berth船台安装
overhead position weld仰焊
overlap焊瘤
oxide covered electrode酸性焊条
oxy cutt氧矛切割
pad fitt配垫块
paint line水线标志
panel板列
paraffin test煤油涂检法
parallel misalignment两轴偏移
parametric curve with sle flecnode单拐参数曲线
parent metal母材
passivat钝化处理
phosphat磷化处理
phosphat and electrocoat酸洗磷化电泳涂漆流水线
photosensitive mark感光号料
pickl酸洗处理
pickl bath酸洗池
pickl waste treatment废酸液处理
pier突堤码头
pincushion distortion枕形畸变
pinhole针状气孔
pipe bender弯管机
pipe bend弯管
pipe clean管子清洗
pipe coil machine螺旋形卷管机
pipe cutt管子下料
pipe cutt machine管子切割机
pipe edge gas cutt machine管端型线气割机
pipe expand胀管
pipe insulat管子绝缘
pipe reshap and position校管
pipe reshap machine校管机
pipeline connection管路连接
pip and systems船舶综合放样
pip layout管系放样
pip mathematical layout管系数学放样
pit for gate门坑
pitch of weld焊段节距
plasma cutt等离子切割
plate alignment拼板
plate gate插板式坞门
plate straightener辊式矫平机
plug weld塞焊
pneumatic mark punch风动号料冲头
point by point method of modification逐点修改法
pontoon趸船
pontoon type gate浮箱式坞门
porosity气孔
positioner摇摆胎架
positioner for unit erection at berth船台装配定位器
position定位
position by dummy shaft工艺轴定位
position by mark划线定位
position by optical sight光学定位
position by runn a line拉线定位
position of boiler stool锅炉底座定位
position of crosshead guide导板定位
position of cylinder block汽缸体定位
position of drum锅筒定位
position of engine bed机座定位
position of engine frame机架定位
position strip定位马
positive projection正片投影
postheat焊后缓冷
precision cast of propeller螺旋桨无余量铸造
preheat预热
press压力机
press bend压弯
press plastic bear material into stern tube尾轴管衬套塑料嵌套
pressure bear layer乘压层
profile draw仿形图
profile gas cutt machine靠模气割机
projected frame line on selected mould section改型肋骨型线
projection mark投影号料
projection mark table投影号料台
projection room投影室
projection tower投影塔
propeller balance test螺旋桨校平衡
propeller pitch guage螺距规
properties of welded joint焊接接头性能
pull
out type fractune层状撕裂
pull eye拉环
pure bend纯弯板
pyramid method of hull construction塔式建造法
quay for material transport材料码头
quay for moor trial试车码头
quay for traffic交通码头
quay outfitt and installation码头安装
railway slip船排滑道
recondition of crankshaft曲轴修正
record of product产品经历簿
rectification of distortion矫形
rectification of distortion by flame火工矫形
rectification of distortion by flame heat and water cool水火矫形
recurrent force回弹力
recurrent magnitude回弹量
red shrinkage for crankshaft曲轴红套
reference基准
reference for assembl装配基准
reference line for assembl装配定位线
reference line for inspection检验线
reinforcement加强高
relative distortion相对畸变
remote control descal machine遥控除锈机
repair weld补焊
repair dock修船坞
repeated times of repair weld补焊次数
residual hydrogen content残余氢含量
resistance weld电阻焊
restest复验
restraint butt joint crack test刚性对接抗裂试验
restraint circularpatch crack test刚性镶块抗裂试验
restraint cruciform crack test刚性十字接头抗裂试验
restraint fillet weld crack test刚性角焊缝抗裂试验
restraint fillet weld crack test in overhead position刚性仰角焊抗裂试验
returned table of offsets完工型值表
reversed polarity反接
roll bend滚弯
roll shear滚剪
roll shear machine滚剪机
root crack根部裂缝
root face钝边
root of weld焊根
root open装配间隙
root radius坡口半径
rotor assembly转子装配
round fillet weld crack test弧形角接抗裂试验
rubber mold form橡皮模成型
runn a measur wire拉线
runn in跑合
rust removal of steel钢材除锈
sagged weld塌陷
sand blast喷沙除锈
scale draw transparency投影底图
scale loft比例放样
scale loft table比例放样台
scarf削斜
scor on bear metal轴承起线
scour冲刷
scrap of bera轴承刮削
scrapp of propeller boss螺旋桨锥孔修正
scrapp propeller boss in vertical position立式配锥孔
scrapp propeller boss in horizontal position横式配锥孔
sea trial航行实验
seal run封底焊
seam arrangement板缝排列
seam arrangement program板缝排列程序
secondary rust removal二次除锈
section分段
section assembl分段装配
section assembly flow line分段装配流水线
section mould加工洋板
section pickl分段酸洗除锈
sectional curved method剖面线法
sectional method of hull construction分段建造法
secur tube in tube sheet管板连接
selected mould section
seperate method of assembl分离装配法
sequence of erection and weld装配焊接顺序
sett of top dead center找止点
shaft alignment by wir拉钢丝线法
shaft grind segnent轴模
shaft liner bond轴套粘接
shape factor of weld焊缝成形系数
shapes straighten machine型钢矫直机
shear剪切
shear and punch machine联合冲剪机
shear machine剪床
shear squence剪切顺序
shell pate development外板展开
shell plate development program外板展开程序
shielded metal arc weld手弧焊
shims fitt配垫块
ship delivery交船
ship directional quay引船驳岸
ship output船舶产量
shipbuild information data process造船信息数据处理系统
shipbuild period造船周期
shipbuild technolgy造船工艺
shiplifter升船机
shipyard combined plate bend and flang machine造船用滚压两用机
shipyard roll press造船用滚压两用机
shore定位马
short arc weld短弧焊
short circuit transfer短路过渡
short of water失水
shot blast form喷丸成型
shot blast抛丸除锈
shot blast machine抛丸除锈机
shot blast room抛丸室
shot peen喷丸除锈
shrinkage slip off曲轴套合滑移
shrink of disc叶轮套装
shrink on for crankshaft曲轴套合
side block舭墩
side keel block边墩
side launch横向下水
side slipway横向滑道
sideward method of hull section construction侧装法
sight column望广柱
sle bevel groove半V型坡口
sketch for mark off号料草图
slab for pipe mark管子划线平台
slag detachability脱渣性
slag inclusion夹渣
sleeve joint套管接头
slid layer滑动层
slid way滑板
slip spac increment滑道间距增量
slip stopper保险撑
slipway for steel roller launch钢珠滑道
slope of slipway船台坡度
solder钎料
solder钎焊
solid construction wharf固定码头
spatter飞溅
specialized mould bed专用胎架
speed test of life boat救生艇速度试验
spherical shaped plate球形板
spinn旋压
spline function样条函数
spray pant喷涂
spray pickl喷淋酸洗
spray pickl in circulation循环喷射酸洗
spray transfer喷射过渡
spray transfer in pulsed power weld脉冲喷射过渡
spray of plastic on stern tube bear尾轴管轴承塑料喷涂
spr back弯曲回弹
spr contact weld弹力焊
stability test of life boat救生艇稳性试验
stack cutt迭板切割
staggered intermittent fillet weld交错间断焊缝
standard technological procedure典型工艺
standardization run航速实验
start起动
static characteristic of arc电弧静特性
static test of propeller螺旋桨浆静平衡试验
statical table on defective items废品分系统计表
station No站号
steam blow吹管
steel ball method of launch钢珠下水
steel levell and straighten钢材矫正
steel preheat钢材预热
steel pretreatment刚材预处理
steer test in trial舵装置效用实验
still tide平潮
stopp test惯性试验
straight line slipway直线滑道
straight polarity正接
straighten of shapes型钢矫直
strapped joint盖板接头
strength test of life boat救生艇强度试验
strength weld工作焊缝
stress relief anneal of boiler锅炉热处理
stretch bend拉弯
stretch metal around edges of sheet放边
stretch metal in center portion of sheet放中
stripp film clean可剥性薄膜除锈
structural mathematical process结构数学处理
structural
member development构件展开
structural member loft结构放样
structural process program结构处理程序
stud weld螺柱焊
submerged arc weld埋弧焊
substained backfire回火
surfac堆焊
surplus straight edge剩余直边
survey after completion完工检验
survey of assembly angle装配夹角测量
survey of declivity倾斜度测量
sweat渗水
symbols for hull steel fabrication船体加工符号
symmetrical weld对称焊缝
synchronized scann projection同步扫描投影
synthetic weld test模拟焊接热循环试验
table of weight record重量登记簿
tack weld定位焊
tandem dock串联式船坞
tandem shipbuild method串联造船法
tangential development method切面展开法
technical appraisal for product产品技术鉴定书
technical identification of product产品技术质量证明书
technological instruction工艺规程
technological process工艺过程
technology of hull construction船体建造工艺
Tee jointT型接头
Tekken type crack testY型坡口抗裂试验
template样板
template draw样板图
template for secondary mark装配划线样板
templet mould of propeller螺旋桨样板造型
temporary stiffen bar临时加强材
tensile test拉力实验
tension test for anchor锚拉力试验
tension test for anchor chain锚链拉力实验
test at random from batch抽验
test of emergency gene rat set应急发电机组起动、效用试验
test of eng试车
test of pip on board管系效用实验
test of pumps on board泵效用实验
test weld试验焊缝
thickness modification in plate development板厚修正
three cylinder frame bend machine三缸肋骨冷弯机
threshold hollow滑道末端凹口
tide潮汐
tide lever潮位
TIG weld非熔化级气体保护焊
tight metal around edges of sheet收边
tight metal in center portion of sheet收中
tighten of bolts in hot state螺栓热紧
tightness test of pipeline管路密封性试验
tilt device回转装置
tilt jig回转胎架
tilt test倾斜试验
timber wedge楔木
time on build berth船台周期
tim校正时
tipp尾落
toe crack焊趾裂缝
torquemeter扭力测功器
torsional deflection旁弯变形
torsional vibration measurement of shaft轴系扭振测量
tow equipment test拖曳设备试验
trac of shaft line by light光学找中法
transfer efficiency过渡系数
transition pit横移坑
transition section过度段
transition zone横移区
transitional layer过渡层
transverse seam横向接缝
transverse weld横向焊缝
triangular template三角加工样板
tribe of body lines横剖线族
tribe of water lines水线族
trible of buttock lines纵剖线族
trigger止滑器
tube search of boiler炉管通球检查
turn circle test回转试验
twin arc fillet weld对弧焊
two gate caisson人字式坞门
two w build berth双翼船台
ultrasonic detection超声波探伤
unconfined system explosion form无模爆炸成形
under water cutt水下切割
underbead crack焊道下裂缝
underbe
ad crack test焊道下裂缝试验
undercut咬边
underwater weld水下焊接
union purchases test双杆操作实验
unit分段
unit assembl分段装配
unit assembl of ship machinery船舶机械单元安装
unit erection at berth船台装配
unit outfitt单元安装
up to slipway上排
upper edge line上口线
upright method of hull section construction正装法
upsidedown method of hull section construction倒装法
vacuum test真空盒法
valve lapp伐面研磨
vapor lock气塞
variational method变分法
vertical down weld下行焊
vertical position weld立焊
vertical template of hull assembly高度标杆线
visual inspection外观检验
water jet test冲水法
water lever水位
water test水压实验
water test of life boat救生艇水密实验
water test of sterntube尾轴管水压实验
water test of tailshaft sleeve轴套水压实验
water tightness水密性
wav deformation凹凸度变形
wav deformation around edges边缘波浪变形
way end pressure滑道末端压力
weight of up to slipway上排重量
weld焊缝
weld bead焊道
weld bond熔合线
weld crack焊接裂缝
weld defects焊接缺陷
weld for fix固定焊缝
weld gauge焊缝量规
weld imperfections焊接缺陷
weld metal焊缝金属
weld segment焊段
weld thermal cycle焊接热循环曲线
weld toe焊趾
weld width焊缝宽度
weldability可焊性
weldability test可焊性试验
welded joint焊接接头
weld焊接
weld condition焊接条件
weld current焊接电流
weld direction焊接方向
weld distortion焊接变形
weld materials焊接材料
weld of dissimilar metals异种金属焊接
weld of plastic pipe塑料焊接
weld parameter焊接工艺参数
weld position焊接位置
weld power source焊接电源
weld prior to bend先焊后弯
weld rate焊接速度
weld sequence焊接顺序
weld speed焊接速度
weld stress焊接应力
weld structure焊接结构
weld symbol焊接符号
weld wire焊丝
weld with back衬垫焊
weld with weav摆动焊
weldment焊件
wet sand blast湿喷沙除锈
wharf码头
wharfboat趸船
width of heat affect zone热影响区宽度
wire feed rate送丝速度
wire feed speed送丝速度
wire template管子样棒
wormhole针状气孔
zero avail line零轴线
zero point零点
zone of pivot pressure action前支架压力作用区