BTA204X-600B中文资料

Three quadrant triacs BTA204X series B and C

high commutation

GENERAL DESCRIPTION

QUICK REFERENCE DATA

Passivated high commutation triacs in SYMBOL

PARAMETER

MAX.MAX.MAX.UNIT a plastic full pack envelope intended for use in circuits where high static and BTA204X-500B 600B 800B dynamic dV/dt and high dI/dt can BTA204X-500C 600C 800C occur.These devices will commutate V DRM Repetitive peak 500600800V the full rated rms current at the off-state voltages maximum rated junction temperature I T(RMS)RMS on-state current

444A without the aid of a snubber.

I TSM

Non-repetitive peak on-state 25

current

PINNING - SOT186A

PIN CONFIGURATION

SYMBOL

LIMITING VALUES

Limiting values in accordance with the Absolute Maximum System (IEC 134).SYMBOL PARAMETER

CONDITIONS

MIN.MAX.UNIT -500-600-800V DRM Repetitive peak off-state -5001

6001800

V voltages

I T(RMS)RMS on-state current full sine wave;-4

T hs ≤ 92 ?C I TSM

Non-repetitive peak full sine wave;on-state current

T j = 25 ?C prior to surge t = 20 ms -25A t = 16.7 ms -27A I 2t I 2t for fusing

t = 10 ms

3.1A 2s dI T /dt Repetitive rate of rise of I TM = 6 A; I G = 0.2 A;100A/μs on-state current after dI G /dt = 0.2 A/μs triggering

I GM Peak gate current -2A V GM Peak gate voltage -5V P GM Peak gate power -5W P G(AV)Average gate power over any 20 ms -0.5W period

T stg Storage temperature -40150?C T j

Operating junction -

125

temperature

1 Although not recommended, off-state voltages up to 800V may be applied without damage, but the triac may switch to the on-state. The rate of rise of current should not exceed 6 A/μs.

ISOLATION LIMITING VALUE & CHARACTERISTIC

T hs = 25 ?C unless otherwise specified SYMBOL PARAMETER

CONDITIONS

MIN.TYP.MAX.UNIT V isol R.M.S. isolation voltage from all f = 50-60 Hz; sinusoidal -2500

V three terminals to external waveform;

heatsink

R.H. ≤ 65% ; clean and dustfree

C isol

Capacitance from T2 to external f = 1 MHz -

10-

heatsink

THERMAL RESISTANCES

SYMBOL PARAMETER CONDITIONS

MIN.TYP.MAX.UNIT R th j-hs Thermal resistance full or half cycle

junction to heatsink with heatsink compound -- 5.5K/W without heatsink compound --7.2K/W R th j-a

Thermal resistance in free air

-55

-K/W

junction to ambient

STATIC CHARACTERISTICS

T j = 25 ?C unless otherwise stated SYMBOL PARAMETER CONDITIONS

MIN.

TYP.

MAX.UNIT

BTA204X-...B ...C I GT

Gate trigger current 2

V D = 12 V; I T = 0.1 A T2+ G+--5035mA T2+ G---5035mA T2- G---5035mA I L

Latching current

V D = 12 V; I GT = 0.1 A T2+ G+--3020mA T2+ G---4530mA T2- G---3020mA I H Holding current V D = 12 V; I GT = 0.1 A --30

mA V T On-state voltage I T = 5 A

- 1.4 1.7V V GT Gate trigger voltage V D = 12 V; I T = 0.1 A -0.7 1.5V V D = 400 V; I T = 0.1 A;0.250.4-V T j = 125 ?C

I D

Off-state leakage current

V D = V DRM(max); T j = 125 ?C

-0.1

0.5

mA DYNAMIC CHARACTERISTICS

T j = 25 ?C unless otherwise stated SYMBOL PARAMETER

CONDITIONS

MIN.TYP.

UNIT

BTA204X-...B ...C dV D /dt Critical rate of rise of V DM = 67% V DRM(max); T j = 125 ?C;

10001000-V/μs off-state voltage

exponential waveform; gate open circuit dI com /dt Critical rate of change of V DM = 400 V; T j = 125 ?C; I T(RMS) = 4 A;63-A/ms commutating current dV com /dt = 20V/μs; gate open circuit t gt

Gate controlled turn-on I TM = 12 A; V D = V DRM(max); I G = 0.1 A;--2

μs

time

dI G /dt = 5 A/μs

2 Device does not trigger in the T2-, G+ quadrant.

MECHANICAL DATA

Notes

1. Refer to mounting instructions for F-pack envelopes.

2. Epoxy meets UL94 V0 at 1/8".

DEFINITIONS

Data sheet status

Objective specification This data sheet contains target or goal specifications for product development. Preliminary specification This data sheet contains preliminary data; supplementary data may be published later. Product specification This data sheet contains final product specifications.

Limiting values

Limiting values are given in accordance with the Absolute Maximum Rating System (IEC 134). Stress above one or more of the limiting values may cause permanent damage to the device. These are stress ratings only and operation of the device at these or at any other conditions above those given in the Characteristics sections of this specification is not implied. Exposure to limiting values for extended periods may affect device reliability. Application information

Where application information is given, it is advisory and does not form part of the specification.

? Philips Electronics N.V. 1998

All rights are reserved. Reproduction in whole or in part is prohibited without the prior written consent of the copyright owner.

The information presented in this document does not form part of any quotation or contract, it is believed to be accurate and reliable and may be changed without notice. No liability will be accepted by the publisher for any consequence of its use. Publication thereof does not convey nor imply any license under patent or other industrial or intellectual property rights.

LIFE SUPPORT APPLICATIONS

These products are not designed for use in life support appliances, devices or systems where malfunction of these products can be reasonably expected to result in personal injury. Philips customers using or selling these products for use in such applications do so at their own risk and agree to fully indemnify Philips for any damages resulting from such improper use or sale.