MAX4253ESD+中文资料

General Description

The MAX4249–MAX4257 low-noise, low-distortion oper-ational amplifiers offer rail-to-rail outputs and single-supply operation down to 2.4V. They draw 400μA of quiescent supply current per amplifier while featuring ultra-low distortion (0.0002% THD), as well as low input voltage-noise density (7.9nV/√Hz )and low input current-noise density (0.5fA/√Hz ). These features make the devices an ideal choice for portable/battery-powered applications that require low distortion and/or low noise.For additional power conservation, the MAX4249/MAX4251/MAX4253/MAX4256 offer a low-power shut-down mode that reduces supply current to 0.5μA and puts the amplifiers’ outputs into a high-impedance state. The MAX4249-MAX4257’s outputs swing rail-to-rail and their input common-mode voltage range includes ground. The MAX4250–MAX4254 are unity-gain stable with a gain-bandwidth product of 3MH z.The MAX4249/MAX4255/MAX4256/MAX4257 are inter-nally compensated for gains of 10V/V or greater with a gain-bandwidth product of 22MHz. The single MAX4250/MAX4255 are available in space-saving 5-pin SOT23packages. The MAX4252 is available in an 8-bump chip-scale package (UCSP?) and the MAX4253 is available in a 10-bump UCSP. The MAX4250AAUK comes in a 5-pin SOT23 package and is specified for operation over the automotive (-40°C to +125°C) temperature range.

Applications

Wireless Communications Devices PA Control

Portable/Battery-Powered Equipment Medical Instrumentation ADC Buffers

Digital Scales/Strain Gauges

Features

?Available in Space-Saving UCSP, SOT23, and μMAX ?Packages

?Low Distortion: 0.0002% THD (1k Ωload)

?400μA Quiescent Supply Current per Amplifier ?Single-Supply Operation from 2.4V to 5.5V ?Input Common-Mode Voltage Range Includes Ground

?Outputs Swing Within 8mV of Rails with a 10k ΩLoad

?3MHz GBW Product, Unity-Gain Stable (MAX4250–MAX4254)

22MHz GBW Product, Stable with A V ≥10V/V (MAX4249/MAX4255/MAX4256/MAX4257)?Excellent DC Characteristics

V OS = 70μV I BIAS = 1pA

Large-Signal Voltage Gain = 116dB ?Low-Power Shutdown Mode

Reduces Supply Current to 0.5μA

Places Outputs in a High-Impedance State ?400pF Capacitive-Load Handling Capability

MAX4249–MAX4257

UCSP , Single-Supply, Low-Noise, Low-Distortion, Rail-to-Rail Op Amps

________________________________________________________________Maxim Integrated Products

1

19-1295; Rev 7; 4/05

For pricing, delivery, and ordering information,please contact Maxim/Dallas Direct!at 1-888-629-4642, or visit Maxim’s website at https://www.360docs.net/doc/988042035.html,.

Ordering Information continued at end of data sheet.

Selector Guide appears at end of data sheet.

UCSP is a trademark and μMAX is a registered trademark of Maxim Integrated Products, Inc.

Pin Configurations

M A X 4249–M A X 4257

UCSP , Single-Supply, Low-Noise,

Low-Distortion, Rail-to-Rail Op Amps

ABSOLUTE MAXIMUM RATINGS

ELECTRICAL CHARACTERISTICS

(V DD = 5V, V SS = 0, V CM = 0, V OUT = V DD /2, R L tied to V DD /2, SHDN = V DD , T A = T MIN to T MAX , unless otherwise noted. Typical val-ues are at T A = +25°C.) (Notes 2, 3)

Stresses beyond those listed under “Absolute Maximum Ratings” may cause permanent damage to the device. These are stress ratings only, and functional operation of the device at these or any other conditions beyond those indicated in the operational sections of the specifications is not implied. Exposure to absolute maximum rating conditions for extended periods may affect device reliability.

Power-Supply Voltage (V DD to V SS )......................+6.0V to -0.3V Analog Input Voltage (IN_+, IN_-)....(V DD + 0.3V) to (V SS - 0.3V)SHDN Input Voltage......................................6.0V to (V SS - 0.3V) Output Short-Circuit Duration to Either Supply..........Continuous Continuous Power Dissipation (T A = +70°C)

5-Pin SOT23 (derate 7.1mW/°C above +70°C)...........571mW 8-Bump UCSP (derate 4.7mW/°C above +70°C)........379mW 8-Pin μMAX (derate 4.5mW/°C above +70°C)............362mW 8-Pin SO (derate 5.88mW/°C above +70°C)...............471mW 10-Bump UCSP (derate 6.1mW/°C above +70°C)......484mW 10-Pin μMAX (derate 5.6mW/°C above +70°C)...........444mW 14-Pin SO (derate 8.33mW/°C above +70°C)..............667mW Operating Temperature Range ...........................-40°C to +85°C MAX4250AAUK .............................................-40°C to +125°C Junction Temperature......................................................+150°C Storage Temperature Range.............................-65°C to +150°C Lead Temperature (soldering, 10s).................................+300°C Bump Temperature (soldering) (Note 1)

Infrared (15s)................................................................+220°C Vapor Phase (60s)........................................................+215°C

Note 1:

This device is constructed using a unique set of packaging techniques that impose a limit on the thermal profile the device can be exposed to during board-level solder attach and rework. This limit permits only the use of the solder profiles rec-ommended in the industry-standard specification, JEDEC 020A, paragraph 7.6, Table 3 for IR/VPR and Convection Reflow. Preheating is required. Hand or wave soldering is not allowed.

MAX4249–MAX4257

UCSP , Single-Supply, Low-Noise,Low-Distortion, Rail-to-Rail Op Amps

_______________________________________________________________________________________3

ELECTRICAL CHARACTERISTICS (continued)

M A X 4249–M A X 4257

UCSP , Single-Supply, Low-Noise,

Low-Distortion, Rail-to-Rail Op Amps 4_______________________________________________________________________________________

ELECTRICAL CHARACTERISTICS (continued)

(V DD = 5V, V SS = 0, V CM = 0, V OUT = V DD /2, R L tied to V DD /2, SHDN = V DD , T A = T MIN to T MAX , unless otherwise noted. Typical val-ues are at T A = +25°C.) (Notes 2, 3)

Note 4:Guaranteed by the PSRR test.

Note 5:Offset voltage prior to reflow on the UCSP.Note 6:Guaranteed by design.

Note 7:Lowpass-filter bandwidth is 22kHz for f = 1kHz and 80kHz for f = 20kHz. Noise floor of test equipment = 10nV/√Hz .

MAX4249–MAX4257

UCSP , Single-Supply, Low-Noise,Low-Distortion, Rail-to-Rail Op Amps

_______________________________________________________________________________________

5

105

201525303540

-95-55-35-75-13728496990110131152172192

MAX4251/MAX4256

INPUT OFFSET VOLTAGE DISTRIBUTION

V OS (μV)N U M B E R O F U N I T S

-250

-100-150-200

-50050100150

200250

-40

-20

20

40

60

80

OFFSET VOLTAGE vs. TEMPERATURE

TEMPERATURE (°C)

V O S (μV )

-500

100

50

150

200

-0.5

1.50.5

2.5

3.5

4.5

INPUT COMMON-MODE VOLTAGE (V)

I N P U T O F F S E T V O L T A G E (μV

)

INPUT OFFSET VOLTAGE

vs. INPUT COMMON-MODE VOLTAGE

00.30.20.10.40.50.6

43125678910OUTPUT VOLTAGE vs. OUTPUT LOAD CURRENT

OUTPUT LOAD CURRENT (mA)O U T P U T V O

L T A G E (V )

0.030.020.010.040.050.060.07

0.080.090.10

-400-2020604080OUTPUT VOLTAGE SWING (V OH )

vs. TEMPERATURE

TEMPERATURE (°C)V D D - V O H (V )

0.02

0.010.030.040.050.06

-400-2020604080

OUTPUT VOLTAGE SWING (V OL )

vs. TEMPERATURE

TEMPERATURE (

°C)

V O L (V )50706010090801301201101400

100

50

150

200

250

LARGE-SIGNAL VOLTAGE GAIN vs. OUTPUT VOLTAGE SWING

V OUT

SWING FROM EITHER SUPPLY (mV)

A V (d

B )

60

7080

90100110120130140

50100150200250LARGE-SIGNAL VOLTAGE GAIN vs. OUTPUT VOLTAGE SWING

V OUT SWING FROM EITHER SUPPLY (mV)

A V (d

B )

5070

601009080130120110140

100

50

150200250

LARGE-SIGNAL VOLTAGE GAIN vs. OUTPUT VOLTAGE SWING

V OUT SWING FROM EITHER SUPPLY (mV)

A V (d

B )

Typical Operating Characteristics

(V DD = 5V, V SS = 0, V CM = V OUT = V DD /2, input noise floor of test equipment =10nV/√Hz for all distortion measurements, T A = +25°C, unless otherwise noted.)

M A X 4249–M A X 4257

UCSP , Single-Supply, Low-Noise,

Low-Distortion, Rail-to-Rail Op Amps 6_______________________________________________________________________________________

50

80706090100110

1201301401500

10050150200250

LARGE-SIGNAL VOLTAGE GAIN vs. OUTPUT VOLTAGE SWING

V OUT SWING FROM EITHER SUPPLY (mV)

A V (d

B )

100110

105

115

120

125

-40

-20

20

60

40

80

LARGE-SIGNAL VOLTAGE GAIN

TEMPERATURE (°C)

A V (d

B )

340

380360400

420440460

-40

-20

20

60

40

80

SUPPLY CURRENT AND SHUTDOWN SUPPLY CURRENT vs. TEMPERATURE

TEMPERATURE (°C)

S H U T D O W N S U P P L Y C U R R E N T (μA )

S U P P L Y C U R R E N T (μA )

320340360380400

4204400

0.10.20.30.4

0.50.6

1.8

2.8

2.3

3.3

3.8

4.3

4.8

5.35.5

SUPPLY CURRENT AND SHUTDOWN SUPPLY CURRENT vs. SUPPLY VOLTAGE

SUPPLY VOLTAGE (V)

S U P P L Y C U R R E N T (μA )S H U T D O W N S U P P L Y C U R R E N T (μ

A )

2000

1000.001

0.1

1

0.01

5

SUPPLY CURRENT vs. OUTPUT VOLTAGE

OUTPUT VOLTAGE (V)

S U P P L Y C U R R E N T (μ

A )

1000

400

40

60

80120100180

1601401.8

2.3

2.8

3.3

3.8

4.3

4.8

5.3

INPUT OFFSET VOLTAGE vs. SUPPLY VOLTAGE

SUPPLY VOLTAGE (V)

V O S (μV )

60-40100

10k

100k

1M

1k

10M

MAX4250–MAX4254

GAIN AND PHASE vs. FREQUENCY

-20-100-30FREQUENCY (Hz)G A I N (d B )

P H A S E (D E G R E E S )1020304050180-72-3603672108

144

60-40100

10k

100k

1M

1k

10M

MAX4249/MAX4255/MAX4256/MAX4257 GAIN AND PHASE vs. FREQUENCY

-20-100-30FREQUENCY (Hz)

G A I N (d B )P H A S E (D E G R E E S )

1020304050180-72-3603672108

144

-100-110

1

1k 10k 100k 1M 1010010M

MAX4250–MAX4254

POWER-SUPPLY REJECTION RATIO

-80-70-60-90FREQUENCY (Hz)

P S R R (d B )

-50-40-30-20-10Typical Operating Characteristics (continued)

(V DD = 5V, V SS = 0, V CM = V OUT = V DD /2, input noise floor of test equipment =10nV/√Hz for all distortion measurements, T A = +25°C, unless otherwise noted.)

MAX4249–MAX4257

UCSP , Single-Supply, Low-Noise,Low-Distortion, Rail-to-Rail Op Amps

_______________________________________________________________________________________

7

10000.1

1k

10k

100k 1M

10M

OUTPUT IMPEDANCE vs. FREQUENCY

FREQUENCY (Hz)

O U T P U T I M P E D A N C E (Ω)

1

10

100

30010

100

1k 10k

100k

INPUT VOLTAGE-N0ISE DENSITY

vs. FREQUENCY

M A X 4249-57 T O C 20

FREQUENCY (Hz)

V n -E Q U I V A L E N T I N P U T N O I S E -V O L T A G E (n V /H z )

510152025200nV/div

1s/div

0.1Hz TO 10Hz P-P NOISE

V DD = 3V OR 5V

V P-P NOISE = 760nV P-P

-160

-140-120-100-80-60-40-200

MAX4250–MAX4254 FFT OF DISTORTION AND NOISE

FREQUENCY (Hz)

A M P L I T U D E (d

B c )

10

5k

10k

15k

20k

R L = 1k Ω f O = 1kHz A V = 1

f O

HD2HD3

HD4HD5

V OUT = 2V P-P

-140

-120

-100-80-60-40-20020

10

5k

10k

15k

20k

MAX4249/MAX4255/MAX4256/MAX4257

FFT OF DISTORTION AND NOISE

FREQUENCY (Hz)

A M P L I T U D E (d

B c )

V OUT = 4V P-P

f O = 1kHz

HD2

HD3

V IN

10k Ω

100k Ω

11k Ω

f O

V O

0.001

0.01

0.1

110

2

1

3

4

5

MAX4250–MAX4254

TOTAL HARMONIC DISTORTION PLUS NOISE

OUTPUT VOLTAGE (V P-P )

T H D +N (%)

0.0010.01

0.1

110

2

1

3

OUTPUT VOLTAGE (V P-P )

T H D +N (%)

MAX4250–MAX4254

TOTAL HARMONIC DISTORTION PLUS NOISE vs. OUTPUT VOLTAGE SWING (V = 3V)

0.001

0.01

0.11

3

4

1

2

5

OUTPUT VOLTAGE (V P-P )

T H D +N (%)

MAX4249/MAX4255/MAX4256/MAX4257TOTAL HARMONIC DISTORTION PLUS NOISE

vs. OUTPUT VOLTAGE SWING

0.0001

0.01

0.001

0.1

1

10

1k

100

10k

MAX4250–MAX4254

TOTAL HARMONIC DISTORTION PLUS NOISE vs. FREQUENCY

FREQUENCY (Hz)

T H D +N (%)

Typical Operating Characteristics (continued)

(V DD = 5V, V SS = 0, V CM = V OUT = V DD /2, input noise floor of test equipment =10nV/√Hz for all distortion measurements, T A = +25°C, unless otherwise noted.)

M A X 4249–M A X 4257

UCSP , Single-Supply, Low-Noise,

Low-Distortion, Rail-to-Rail Op Amps 8_______________________________________________________________________________________

0.0001

0.001

0.010.1

10

1k

100

10k

MAX4250–MAX4254

TOTAL HARMONIC DISTORTION FREQUENCY (Hz)

T H D +N (%)

V OUT 200mV/div

1.5V

0.5V

2μs/div

MAX4250–MAX4254

LARGE-SIGNAL PULSE RESPONSE

V DD = 3V R L = 10k ΩC L = 100pF V IN = 1V PULSE 0.6V

0.5V

MAX4250–MAX4254

SMALL-SIGNAL PULSE RESPONSE

V OUT 20mV/div

V DD = 3V R L = 10k ΩC L = 100pF

V IN = 100V PULSE 2μs/div

2V

1V

MAX4249/MAX4255/MAX4256/MAX4257

LARGE-SIGNAL PULSE RESPONSE

V OUT 200mV/div

V DD = 3V R L = 10k ΩC L = 100pF

V IN = 100mV PULSE A V = 10

1.6V

1.5V

MAX4249/MAX4255/MAX4256/MAX4257 SMALL-SIGNAL PULSE RESPONSE

V OUT 50mV/div

V DD = 3V R L = 10k ΩC L = 100pF

V IN = 10mV PULSE A V = 102μs/div

140

1300CHANNEL SEPARATION vs. FREQUENCY

M A X 4249-57 T O C 33

FREQUENCY (Hz)

C H A N N E L S E P A R A T I O N (d B )

1001101209080701k

100k 1M

10k

10M

Typical Operating Characteristics (continued)

(V DD = 5V, V SS = 0, V CM = V OUT = V DD /2, input noise floor of test equipment =10nV/√Hz for all distortion measurements, T A = +25°C, unless otherwise noted.)

MAX4249–MAX4257

UCSP , Single-Supply, Low-Noise,Low-Distortion, Rail-to-Rail Op Amps

_______________________________________________________________________________________

9

Detailed Description

The MAX4249–MAX4257 single-supply operational amplifiers feature ultra-low noise and distortion while consuming very little power. Their low distortion and low noise make them ideal for use as preamplifiers in wide dynamic-range applications, such as 16-bit analog-to-digital converters (see Typical Operating Circuit ). Their high-input impedance and low noise are also useful for signal conditioning of high-impedance sources, such as piezoelectric transducers.

These devices have true rail-to-rail output operation,drive loads as low as 1k Ωwhile maintaining DC accura-

cy, and can drive capacitive loads up to 400pF without oscillation. The input common-mode voltage range extends from V DD - 1.1V to 200mV beyond the negative rail. The push-pull output stage maintains excellent DC characteristics, while delivering up to ±5mA of current.The MAX4250–4254 are unity-gain stable, whereas, the MAX4249/MAX4255/MAX4256/MAX4257 have a higher slew rate and are stable for gains ≥10V/V. The MAX4249/MAX4251/MAX4253/MAX4256 feature a low-power shutdown mode, which reduces the supply cur-rent to 0.5μA and disables the outputs.

The MAX4250AAUK is specified for operation over the automotive (-40°C to +125°C) temperature range.

M A X 4249–M A X 4257

UCSP , Single-Supply, Low-Noise,

Low-Distortion, Rail-to-Rail Op Amps 10

______________________________________________________________________________________

Low Distortion

Many factors can affect the noise and distortion that the device contributes to the input signal. The following guidelines offer valuable information on the impact of design choices on Total Harmonic Distortion (THD).Choosing proper feedback and gain resistor values for a particular application can be a very important factor in reducing TH D. In general, the smaller the closed-loop gain, the smaller the TH D generated, especially when driving heavy resistive loads. Large-value feed-back resistors can significantly improve distortion. The TH D of the part normally increases at approximately 20dB per decade, as a function of frequency.Operating the device near or above the full-power bandwidth significantly degrades distortion.

Referencing the load to either supply also improves the part’s distortion performance, because only one of the MOSFETs of the push-pull output stage drives the out-put. Referencing the load to midsupply increases the part’s distortion for a given load and feedback setting.(See the Total Harmonic Distortion vs. Frequency graph in the Typical Operating Characteristics .)

For gains ≥10V/V, the decompensated devices MAX4249/MAX4255/MAX4256/MAX4257 deliver the best distortion performance, since they have a higher slew rate and provide a higher amount of loop gain for a given closed-loop gain setting. Capacitive loads below 400pF, do not significantly affect distortion results. Distortion performance remains relatively con-stant over supply voltages.

Low Noise

The amplifier’s input-referred, noise-voltage density is dominated by flicker noise at lower frequencies, and by thermal noise at higher frequencies. Because the ther-mal noise contribution is affected by the parallel combi-nation of the feedback resistive network (R F || R G ,Figure 1), these resistors should be reduced in cases where the system bandwidth is large and thermal noise is dominant. This noise contribution factor decreases,however, with increasing gain settings.

For example, the input noise-voltage density of the cir-cuit with R F = 100k Ω, R G = 11k Ω(A V = 10V/V) is e n =15nV/√Hz , e n can be reduced to 9nV/√Hz by choosing R F = 10k Ω, R G = 1.1k Ω(A V = 10V/V), at the expense of greater current consumption and potentially higher distortion. For a gain of 100V/V with R F = 100k Ω, R G =1.1k Ω, the e n is low (9nV/√Hz ).

A V = 2V/V

R F = R G = 10k Ω

2μs/div

A V = 2

R F = R G = 100k Ω C Z = 11pF

100mV/div

2μs/div

Figure 1. Adding Feed-Forward Compensation

Figure 2a. Pulse Response with No Feed-Forward Compensation

Figure 2b. Pulse Response with 10pF Feed-Forward Compensation

MAX4249–MAX4257

UCSP , Single-Supply, Low-Noise,Low-Distortion, Rail-to-Rail Op Amps

______________________________________________________________________________________

11

Using a Feed-Forward Compensation

Capacitor, C Z

The amplifier’s input capacitance is 11pF. If the resis-tance seen by the inverting input is large (feedback network), this can introduce a pole within the amplifier’s bandwidth, resulting in reduced phase https://www.360docs.net/doc/988042035.html,pensate the reduced phase margin by introducing a feed-forward capacitor (C Z ) between the inverting input and the output (Figure 1). This effectively cancels the pole from the inverting input of the amplifier.Choose the value of C Z as follows:

C Z = 11 x (R F / R G ) [pF]

In the unity-gain stable MAX4250–MAX4254, the use of a proper C Z is most important for A V = 2V/V, and A V = -1V/V. In the decompensated MAX4249/MAX4255/MAX4256/MAX4257, C Z is most important for A V = 10V/V. Figures 2a and 2b show transient response both with and without C Z .

Using a slightly smaller C Z than suggested by the for-mula above achieves a higher bandwidth at the expense of reduced phase and gain margin. As a gen-eral guideline, consider using C Z for cases where R G ||R F is greater than 20k Ω(MAX4250–MAX4254) or greater than 5k Ω(MAX4249/MAX4255/MAX4256/MAX4257).

Applications Information

The MAX4249–MAX4257 combine good driving capa-bility with ground-sensing input and rail-to-rail output operation. With their low distortion, low noise, and low-power consumption, these devices are ideal for use in portable instrumentation systems and other low-power,noise-sensitive applications.

Ground-Sensing and Rail-to-Rail Outputs

The common-mode input range of these devices extends below ground, and offers excellent common-mode rejection. These devices are guaranteed not to undergo phase reversal when the input is overdriven (Figure 3).

Figure 4 showcases the true rail-to-rail output operation of the amplifier, configured with A V = 10V/V. The output swings to within 8mV of the supplies with a 10k Ωload,making the devices ideal in low-supply-voltage applica-tions.

Output Loading and Stability

Even with their low quiescent current of 400μA, these amplifiers can drive 1k Ωloads while maintaining excel-lent DC accuracy. Stability while driving heavy capaci-tive loads is another key feature.

4.25V

A V = 1V DD = 5V R L = 10k Ω

20μs/div

V DD = 5V R L = 10k Ω A V = 10f = 1kHz

200μs/div

Figure 3. Overdriven Input Showing No Phase Reversal

Figure 4. Rail-to-Rail Output Operation

Figure 5. Capacitive-Load Driving Circuit

M A X 4249–M A X 4257

UCSP , Single-Supply, Low-Noise,

Low-Distortion, Rail-to-Rail Op Amps 12______________________________________________________________________________________

These devices maintain stability while driving loads up to 400pF. To drive higher capacitive loads, place a small isolation resistor in series between the output of the amplifier and the capacitive load (Figure 5). This resistor improves the amplifier’s phase margin by isolat-ing the capacitor from the op amp’s output. Reference Figure 6 to select a resistance value that will ensure a load capacitance that limits peaking to <2dB (25%).

For example, if the capacitive load is 1000pF, the corre-sponding isolation resistor is 150Ω. Figure 7 shows that peaking occurs without the isolation resistor. Figure 8shows the unity-gain bandwidth vs. capacitive load for the MAX4250–MAX4254.

Power Supplies and Layout

The MAX4249–MAX4257 operate from a single 2.4V to 5.5V power supply or from dual supplies of ±1.20V to ±2.75V. For single-supply operation, bypass the power supply with a 0.1μF ceramic capacitor placed close to the V DD pin. If operating from dual supplies, bypass each supply to ground.

Good layout improves performance by decreasing the amount of stray capacitance and noise at the op amp’s inputs and output. To decrease stray capacitance, min-imize PC board trace lengths and resistor leads, and place external components close to the op amp’s pins.

UCSP Applications Information

For the latest application details on UCSP construction,dimensions, tape carrier information, PC board tech-niques, bump-pad layout, and recommended reflow temperature profile, as well as the latest information on reliability testing results, refer to the Application Note:UCSP—A Wafer-Level Chip-Scale Package on Maxim’s web site at https://www.360docs.net/doc/988042035.html,/ucsp.

Figure 6. Isolation Resistance vs. Capacitive Loading to Minimize Peaking (<2dB)Figure 7. Peaking vs. Capacitive Load

Figure 8. MAX4250–MAX4254 Unity-Gain Bandwidth vs.Capacitive Load

MAX4249–MAX4257

UCSP , Single-Supply, Low-Noise,Low-Distortion, Rail-to-Rail Op Amps

______________________________________________________________________________________13

Typical Operating Circuit

M A X 4249–M A X 4257

UCSP , Single-Supply, Low-Noise,

Low-Distortion, Rail-to-Rail Op Amps 14______________________________________________________________________________________

Ordering Information (continued)

Chip Information

MAX4250/MAX4251/MAX4255/MAX4256 TRANSISTOR COUNT: 170

MAX4249/MAX4252/MAX4253/MAX4257 TRANSISTOR COUNT: 340

MAX4254 TRANSISTOR COUNT: 680

Pin Configurations (continued)

MAX4249–MAX4257

UCSP , Single-Supply, Low-Noise,Low-Distortion, Rail-to-Rail Op Amps

______________________________________________________________________________________15

M A X 4249–M A X 4257

UCSP , Single-Supply, Low-Noise,

Low-Distortion, Rail-to-Rail Op Amps 16______________________________________________________________________________________

Package Information

(The package drawing(s) in this data sheet may not reflect the most current specifications. For the latest package outline information go to https://www.360docs.net/doc/988042035.html,/packages .)

MAX4249–MAX4257

UCSP, Single-Supply, Low-Noise,

Low-Distortion, Rail-to-Rail Op Amps

17

Package Information (continued)

(The package drawing(s) in this data sheet may not reflect the most current specifications. For the latest package outline information

go to https://www.360docs.net/doc/988042035.html,/packages.)

M A X 4249–M A X 4257

UCSP , Single-Supply, Low-Noise,

Low-Distortion, Rail-to-Rail Op Amps 18______________________________________________________________________________________

Package Information (continued)

(The package drawing(s) in this data sheet may not reflect the most current specifications. For the latest package outline information go to https://www.360docs.net/doc/988042035.html,/packages .)

MAX4249–MAX4257

UCSP , Single-Supply, Low-Noise,Low-Distortion, Rail-to-Rail Op Amps

Maxim cannot assume responsibility for use of any circuitry other than circuitry entirely embodied in a Maxim product. No circuit patent licenses are implied. Maxim reserves the right to change the circuitry and specifications without notice at any time.

Maxim Integrated Products, 120 San Gabriel Drive, Sunnyvale, CA 94086 408-737-7600 ____________________19?2005 Maxim Integrated Products

Printed USA

is a registered trademark of Maxim Integrated Products, Inc.

Package Information (continued)

(The package drawing(s) in this data sheet may not reflect the most current specifications. For the latest package outline information go to https://www.360docs.net/doc/988042035.html,/packages .)

相关主题
相关文档
最新文档