SMT不良现象中英文对照表

不良現象中英文對照表

1.缺件(MISSING PARTS) 28.腳未彎(PIN NOT BENT) 55.印章錯誤(WRONG STAMPS)

2.錯件(WRONG PARTS) 29.缺蓋章(MISSING STAMP) 56.尺寸錯誤(DIMENSION WRONG)

3.多件(EXCESSIVE PARTS) 30.缺標籤(MISSING LABEL) 57.二極體壞(DIODE NG)

4.短路(SHORT) 31.缺序號(MISSING S/N) 58.電晶體壞(TRANSISTOR NG)

5.斷路(OPEN) 32.序號錯(WRONG S/N) 59.振盪器壞(X’TL NG)

6.線短(WIRE SHORT) 33.標籤錯(WRONG LABEL) 60.管裝錯誤(TUBES WRONG)

7.線長(WIRE LONG) 34.標示錯(WRONG MARK) 61.阻值錯誤(IMPEDANCE WRONG)

8.拐線(WIRE POOR DDRESS) 35.腳太短(PIN SHORT) 62.版本錯誤(REV WRONG)

9.冷焊(COLD SOLDER) 36.J1不潔(J1 DIRTY) 63.電測不良(TEST FAILURE)

10.包焊(EXCESS SOLDER) 37.錫凹陷(SOLDER SCOOPED) 64.版本未標(NON REV LEBEL)

11.空焊(MISSING SOLDER) 38.線序錯(W/L OF WIRE) 65.包裝損壞(PACKING DAMAGED)

12.錫尖(SOLDER ICICLE) 39.未測試(NO TEST) 66.印章模糊(STAMPS DEFECTIVE)

13.錫渣(SOLDER SPLASH) 40.VR變形(VR DEFORMED) 67.標籤歪斜(LABEL TILT)

14.錫裂(SODER CRACK) 41.PCB翹皮(PCB PEELING) 68.外箱損壞(CARTON DAMAGED)

15.錫洞(PIN HOLE) 42.PCB彎曲(PCB TWIST) 69.點膠不良(POOR GLUE)

16.錫球(SOLDER BALL) 43.零件沾膠(GLUE ON PARTS) 70.IC座氧化(SOCKET RUST)

17.錫橋(SOLDER BRIDGE) 44.零件腳長(PARTS PIN LONG) 71.缺UL標籤(MISSING UL LABEL)

18.滑牙(SCREW LOOSE) 45.浮件(PARTS LIFT) 72.線材不良(WIRE FAILURE)

19.氧化(RUST) 46.零件歪斜(PARTS TILT) 73.零件腳損壞(PIN DAMAGED)

20.異物(FOREIGNER MATERIAL) 47.零件相觸(PARTS TOUCH) 74.金手指沾錫(SOLDER ON GOLDEN FINGERS)

21.溢膠(EXCESSIVE GLUE) 48.零件變形(PARTS DEFORMED) 75.包裝文件錯(RACKING DOC WRONG)

22.錫短路(SOLDER BRIDGE) 49.零件損壞(PARTS DAMAGED) 76.包裝數量錯(PACKING Q’TY WRONG)

23.錫不足(SOLDER INSUFFICIENT) 50.零件腳髒(PIN DIRTY) 77.零件未定位(PARTS UNSEATED)

24.極性反(WRONG POLARITY) 51.零件多裝(PARTS EXCESS) 78.金手指沾膠(GLUE ON GOLDEN FINGERS)

25.腳未入(PIN UNSEATED) 52.零件沾錫(SOLDER ON PARTS) 79.墊片安裝不良(WASHER UNSEATED)

26.腳未出(PIN UNVISIBLE) 53.零件偏移(PARTS SHIFT) 80.線材安裝不良(WIRE UNSEATED)

27.腳未剪(PIN NO CUT) 54.包裝錯誤(WRONG PACKING) 81. 立碑(TOMBSTONE)

SSING UL LABEL)

錫(SOLDER ON GOLDEN FINGERS)錯(RACKING DOC WRONG)

錯(PACKING Q’TY WRONG)

位(PARTS UNSEATED) (GLUE ON GOLDEN FINGERS)不良(WASHER UNSEATED) IRE UNSEATED)