Mstar方案芯片MSD7C51DCE规格书
MSD7C51DCE High Performance DVB-C HD
STB System-on-Chip
Preliminary Data Sheet Version 0.1
? 2015 MStar Semiconductor, Inc. All rights reserved.
MStar Semiconductor makes no representations or warranties including, for example but not limited to, warranties of merchantability, fitness for a particular purpose, non-infringement of any intellectual property right or the accuracy or completeness of this document, and reserves the right to make changes without further notice to any products herein to improve reliability, function or design. No responsibility is assumed by MStar Semiconductor arising out of the application or use of any product or circuit described herein; neither does it convey any license under its patent rights, nor the rights of others.
MStar is a trademark of MStar Semiconductor, Inc. Other trademarks or names herein are only for identification purposes only and owned by their respective owners.
MSD7C51DCE
High Performance DVB-C HD STB System-on-Chip
Preliminary Data Sheet Version 0.1 REVISION HISTORY
Revision No. Description Date
0.1 ?Initial release 08/17/2015
Attention Please: Under the technology license agreement between MStar and Dolby/DivX/Microsoft, MStar is obliged not to provide samples that incorporate Dolby/DivX/Microsoft technology to any third party who is not a qualified licensee of Dolby/DivX/Microsoft respectively.
FEATURES
Single chip that supports STB functionality enabled by a high performance AV CODEC and CPU
n High Performance Microprocessor
?High performance MIPS34Kf CPU with
hardware floating point
?Maximum performance: 1200 DMIPS
?TLB type MMU with 64 dual entries
?32KB I Cache & 32KB D cache
n Transport Stream Processor
?Supports one parallel TS input interface
?Supports playback from TS interfaces, DRAM and files
?Supports time-shifting and PVR functions
?64 PID filters and 64 section filters
n Multi-Standard Video Decoder
?MPEG-1/2/4 Video Decoder
?Supports ISO/IEC 13818-2 MPEG-2 MP@HL video decoding up to 1080p@30fps
?Supports ISO/IEC 14496-2 MPEG-4 SP and ASP video decoding up to 1080p@30fps ?Supports Xvid, DivX1 3.11, 4.x, 5.x, 6.x,
Home Theater & HD profiles Optional
?Supports FLV (Sorenson H.263) video
format
?H.264 Decoder
?Supports ITU-T H.264, ISO/IEC 14496-10 main and high profile up to level 4.1 video
decoding
?Supports resolution up to 1080p@30fps ?AVS/AVS+ Decoder
?Supports Jizhun/Guanbo profile, level 6.0
?Supports resolution up to 1080p@30fps
1Trademark of DivX, Inc.
Optional Please see Ordering Guide for details.
?VC-1 Decoder
?Supports AP@L3
?Supports resolution and frame rate up to 2048x1024p30
?Supports max. bitrate of 20Mbps
?VP8 Decoder
?Supports resolution up to 1080p@30fps
?Supports max. bitrate of 50Mbps
n Hardware JPEG
?Supports sequential mode, single scan
?Supports both color and grayscale pictures
?Supports formats: 422/411/420/444/422/440
?Supports scaling down ratios: 1/2, 1/4, 1/8
?Supports programmable region of interest (ROI) decoding for speedup.
n2D Graphics Engine
?Hardware Graphics Engine for responsive interactive applications
?Supports direct frame buffer (DFB)
?Supported operations:
?Line draw and rectangle fill
?BitBlt, stretch BitBlt, mirror BitBlt and rotate BitBlt
?Raster Operation (ROP), ROP2 and ROP8
?Alpha blending and dithering
n Display Engine
?Supports up to four graphics and one video display planes
?Advanced algorithms for OSD de-flickering
?Built-in high quality Motion-Adaptive(MADi) and Edge Oriented (EODi) deinterlacer
?Independent high quality scaling path for HD and SD outputs
?Built-in contrast and brightness control
n Multi-Standard Audio Decoder
?Audio sampling rate conversion (SRC)
?Supports digital audio decoding:
?MPEG-1, MPEG-2 (Layer I/II), MP3
?AC-3 (Dolby Digital) Optional, E-AC-3 (Dolby Digital Plus) Optional
?AAC-LC 5.1 channel, HE-AAC v1/v2
decoding
?WMA, RA8-LBR decoding
?Supports AC-3Optional stream output through SPDIF
n Video Output Interface
?Four 10-bit video DACs outputs
?Supports 480i, 576i, 480p, 576p, 720p, 1080i, 1080p YPbPr/RGB component output ?Supports 480i and 576i CVBS/S-Video
composite output
?Programmable YC delay
?Programmable hue, contrast, brightness
?Format conversion between different supported formats
?Supports Macrovision 7.1.S1 and AGC 1.4 (480i/576i/480p/576p) Optional
?Digital video encoder
?Supports all NTSC/PAL/SECAM TV Standard
?Supports TTX/CC/WSS/CGMS-A
n Audio Output/Input Interface
?Built-in one stereo DAC for line-out
?Built-in audio line driver for 2Vrms output swing ?S/PDIF digital audio output
?Supports stereo I2S output
?Supports stereo PCM output through HDMI output interface
?Support DD/DD+/DTS bypassing through HDMI output interface
n HDMI Output Interface
?Supports HDMI 1.4a compliant without HEAC and 3D supporting
?HDCP 1.4 encryption engine
?Supports IEC60958 PCM or IEC61937
compressed audio format
?Supports RGB or YCbCr 4:2:2/4:4:4 format Optional Please see Ordering Guide for details.
Optional Please contact MStar sales for the correct suffix for selected CA system.
?Supports deep color 8/10/12-bit color depth per channel and resolutions up to 1080p@60Hz or
720p/1080i@120Hz
?Supports DVI 1.0
?Supports CEC (Consumer Electronics Control) function
n DVB-C Demodulator
?ITU J.83 Annex A/C DVB-C (EN 300 429) complaint
?Supports 1-7.2 M Baud symbol rate
?Automatic blind channel scan ( constellation and symbol rate)
?Supports IF and LIF interfaces
IIS & CNR improvement
n Connectivity
?Supports two USB 2.0 host controller
?Built-in 10/100Mbps Ethernet MAC with PHY interface
n Miscellaneous
?Supports smartcard interface
?Built-in 128MByte 16-bit DDR3 SDRAM
?Bootable SPI interface with serial flash
?Bootable parallel NAND Flash
?Supports CEC (Consumer Electronics Control) function
?SAR, SPI and IRIN interfaces are workable in standby mode
GENERAL DESCRIPTION
The MSD7C51DCE is a highly integrated, cost-effective and high performance SoC for high-definition STB (Set-Top Box) applications. It is configured with DVB-C demodulator, a multi-format audio and video decoder which is capable of decoding MPEG-1/2/4, H.264 (ISO/IEC 14496-10), VC-1, AVS/AVS+ and VP-8 formats.. It has a smartcard interafce and a digital video encoder of supporting CVBS, S-Video, YPbPr output. For digital output, the MSD7C51DCE also has a built-in HDMI 1.4a compliant transmitter.
For multimedia applications, the MSD7C51DCE includes two USB 2.0 host controller and a Ethernet MAC with PHY making it possible for the MSD7C51DCE to decode and record media files via those sources from both network and external storage devices. With built-in high performance MIPS34Kf CPU and DDR3 SDRAM controller, the MSD7C51DCE can fulfill the requirement of modern multimedia applications.
BLOCK DIAGRAM
PIN DIAGRAM (MSD7C51DCE)
V D D P
S P I _H O L D N
S P I _C Z 1
H D M I _T X C N
H D M I _H P D H D M I _S D A
A V D D 33_H D M I T X
H D M I _S C L
H D M I _C E C S P I _D I
G P I O 11
S P I _C K
SPI_WPN PWR_CTRL DVDD_DDR_RX_1.1V
VDDIO_DATA
VDDIO_DRAM
GND
IRIN
SM0_IO SM0_CLK AVDD_DDR VDDC
DVDD_DDR_1.1V SM0_SWITCH
PWM2RESET VDDIO_CMD GPIO2VDDIO_DRAM VDDIO_MCLK VDDIO_LDO PWM1VDDIO_DATA GPIO3SM0_CD UART_TX SPI_D0
SPI_CZ PWM0UART_RX VDDIO_CMD
T S 0_C L K
T S 0_D 7
T S 0_D 6
T S 0_D 5
T S 0_D 3
T S 0_D 2
T S 0_D 4
T S 0_D 0
T S 0_D 1
G P I O 15
G P I O 14
G P I O 19
T S 0_S Y N C
G P I O 12
I 2C M 1_S D A
I 2C M 1_S C L
G P I O 13
V D D C
D M _P 1
D P _P 1
A V D D 33_U S B
G P I O 16
V D D C
T S 0_V L D
VDDP
I2CM0_SCL I2CM0_SDA SAR0GPIO36SAR2SAR1AVDD33_DADC DVB_C_IP ET_LINK_LED GND GPIO35VDDP NC NC DVB_C_IM IF_AGC XAL_OUT XAL_IN SAR3ET_SPEED_LED AVDD33_ETH AVDD33_DMPLL EPHY_RP EPHY_RN EPHY_TP EPHY_TN DP_P0DM_P0VDDC VDDC H D M I _T X 1N
H D M I _T X 0N
I D A C _O U T _G A V D D 33_A U S D M
A V D D 33_N E G _A U
L I N E O U T _L
L I N E O U T _R
A U _V R M
A U _V A G
C N
C P
H D M I _T X 0P
A V D D 33_U S
B I D A
C _O U T _B
I D A C _O U T _R
H D M I _T X C P
I D A C _O U T _X
V D D C
S P D I F _O U T
V D D P
A V D D L _H D M I T X
H D M I _T X 1P
H D M I _T X 2P
H D M I _T X 2N
V D D C
A V D D 33_I D A C
AVDD33_DADC V S Y N C _O U T
H S Y N C _O U T
PIN DESCRIPTION
Audio Interface
Pin Name Function Name Pin Type Function Pin AU_VRM AU_VRM Analog Input Audio DAC Internal Ground119
AU_VAG AU_VAG Analog Output Reference Voltage for Audio Common Mode
118
LINEOUT_R LINEOUT_R Analog Output Audio DAC Output R-channel120 LINEOUT_L LINEOUT_L Analog Output Audio DAC Output L-channel121
CP CP Analog
Input/Output
Charge Pump Flying Cap Positive125
CN CN Analog
Input/Output
Charge Pump Flying Cap Negative124
AVDD33_NEG_A U AVDD33_NEG_A
U
-3.3V Power Charge Pump Output: -3.3V123
Video Interface
Pin Name Function Name Pin Type Function Pin IDAC_OUT_X IDAC_OUT_X Analog Output Video DAC Output114 IDAC_OUT_B IDAC_OUT_B Analog Output Video DAC Output115 IDAC_OUT_G IDAC_OUT_G Analog Output Video DAC Output116 IDAC_OUT_R IDAC_OUT_R Analog Output Video DAC Output117
HSYNC_OUT HSYNC_OUT Digital Output Video Data Hsync Output
44 NF_D6
Digital
Input/Output
Nand Flash Data Input/Output
I2CM1_SDA
Digital
Input/Output
I2C Master Port 1 Serial Data Bit
GPIO17
Digital
Input/Output
General Purpose Input/Output
with Pull Up/Down Resistor
4/8/12/16mA driving strength
VSYNC_OUT VSYNC_OUT Digital Output Video Data Vsync Output
45 NF_D7
Digital
Input/Output
Nand Flash Data Input/Output
I2CM1_SCL Digital Output I2C Master Port 1 Serial Clock
SPDIF_OUT Digital Output Audio S/PDIF output
GPIO18
Digital
Input/Output
General Purpose Input/Output
with Pull Up/Down Resistor
Pin Name Function Name Pin Type Function Pin
4/8/12/16mA driving strength
GPIO Interface
Pin Name Function Name Pin Type Function Pin Location
GPIO2 GPIO2
Digital
Input/Output
General Purpose Input/Output8
with Pull Up/Down Resistor
4/8/12/16mA driving strength
UART_TX1Digital Output UART Transmit Data Output
FUART_RTS0Digital Output Fast UART Transmit Data Output
GPIO3 GPIO3
Digital
Input/Output
General Purpose Input/Output9
with Pull Up/Down Resistor
4/8/12/16mA driving strength
UART_RX Digital Input UART Receive Data Input
FUART_CTS0Digital Input Fast UART Receive Data Input
GPIO11 GPIO11
Digital
Input/Output
General Purpose Input/Output38
with Pull Up Resistor
4mA driving strength
NF_D0
Digital
Input/Output
Nand Flash Data Input/Output
GPIO12 GPIO12
Digital
Input/Output
General Purpose Input/Output39
with Pull Up/Down Resistor
4/8/12/16mA driving strength
NF_D1
Digital
Input/Output
Nand Flash Data Input/Output
I2S_OUT_MCK Digital Output Audio I2S Main Clock
GPIO13 GPIO13
Digital
Input/Output
General Purpose Input/Output40
with Pull Up Resistor
4mA driving strength
NF_D2
Digital
Input/Output
Nand Flash Data Input/Output
I2S_OUT_WS Digital Output Audio I2S Sample Rate Clock
GPIO14 GPIO14
Digital
Input/Output
General Purpose Input/Output41
with Pull Up Resistor
4mA driving strength
NF_D3
Digital
Input/Output
Nand Flash Data Input/Output
Pin Name Function Name Pin Type Function Pin Location I2S_OUT_SDO Digital Output Audio I2S Serial Data
GPIO15 GPIO15
Digital
Input/Output
General Purpose Input/Output42
with Pull Up Resistor
4mA driving strength
FUART_RTS Digital Output Fast UART Transmit Data Output
NF_D4
Digital
Input/Output
Nand Flash Data Input/Output
I2S_OUT_BCK Digital Output Audio I2S Bit Clock
GPIO16 GPIO16
Digital
Input/Output
General Purpose Input/Output43
with Pull Up Resistor
4mA driving strength
FUART_CTS Digital Input Fast UART Receive Data Input
NF_D5
Digital
Input/Output
Nand Flash Data Input/Output
I2S_OUT_MUTE Digital Output Audio I2S Mute Control
GPIO19 GPIO19Digital
Input/Output
General Purpose Input/Output46
with Pull Up Resistor
4mA driving strength
GPIO35 GPIO35Digital
Input/Output
General Purpose Input/Output70
with Pull Up Resistor
4mA driving strength
GPIO36 GPIO36Digital
Input/Output
General Purpose Input/Output71
with Pull Up Resistor
4mA driving strength
PWM0 PWM0Digital Output Pulse Width Modulation Output 4 CFG0 Digital Input Chip Config Bit0
GPIO48
Digital
Input/Output
General Purpose Input/Output
with Pull Up/Down Resistor
4/8/12/16mA driving strength
PWM1 PWM1Digital Output Pulse Width Modulation Output 5 CFG1 Digital Input Chip Config Bit1
GPIO49
Digital
Input/Output
General Purpose Input/Output
with Pull Up/Down Resistor
Pin Name Function Name Pin Type Function
Pin Location 4/8/12/16mA driving strength
PWM2
PWM2 Digital Output Pulse Width Modulation Output 6
CFG2
Digital Input Chip Config Bit2
GPIO52 Digital Input/Output General Purpose Input/Output with Pull Up/Down Resistor 4/8/12/16mA driving strength SAR0
SAR0 Analog Input SARADC Input Channel 0 72
GPIO58 Digital Input/Output General Purpose Input/Output SAR1
SAR1
Analog Input SARADC Input Channel 1 73
GPIO57 Digital Input/Output General Purpose Input/Output SAR2
SAR2
Analog Input SARADC Input Channel 2 74
GPIO56 Digital Input/Output General Purpose Input/Output SAR3 SAR3
Analog Input SARADC Input Channel 3 75
GPIO55
Digital Input/Output
General Purpose Input/Output
Transport Stream Interface
Pin Name Function Name Pin Type Function
Pin TS0_CLK
TS0_CLK Digital Input TS0 clock input (parallel mode) 62
TS0_VLD
TS0_VLD Digital Input TS0 valid input (parallel mode) 53 GPIO21 Digital Input/Output General Purpose Input/Output with Pull Up/Down Resistor 4/8/12/16mA driving strength UART_TX Digital Output UART Transmit Data Output FUART_RTS Digital Output Fast UART Transmit Data Output TS0_SYNC
TS0_SYNC
Digital Input TS0 sync input (parallel mode) 52 GPIO20 Digital Input/Output General Purpose Input/Output with Pull Up/Down Resistor 4/8/12/16mA driving strength TS0_D7
TS0_D[7] Digital Input TS0 data7 input (parallel mode) 61 GPIO29
Digital
General Purpose Input/Output
Pin Name Function Name Pin Type Function Pin
Input/Output with Pull Up/Down Resistor
4/8/12/16mA driving strength
TS0_0_CLK Digital Input TS0 clock input (serial mode)
TS0_D6TS0_D[6]Digital Input TS0 data6 input (parallel mode)
60 GPIO28
Digital
Input/Output
General Purpose Input/Output
with Pull Up/Down Resistor
4/8/12/16mA driving strength
TS0_0_VLD Digital Input TS0 valid input (serial mode)
TS0_D5TS0_D[5]Digital Input TS0 data5 input (parallel mode)
59 GPIO27
Digital
Input/Output
General Purpose Input/Output
with Pull Up/Down Resistor
4/8/12/16mA driving strength
TS0_0_SYNC Digital Input TS0 sync input (serial mode)
TS0_D4TS0_D[4]Digital Input TS0 data4 input (parallel mode)
58 GPIO26
Digital
Input/Output
General Purpose Input/Output
with Pull Up/Down Resistor
4/8/12/16mA driving strength
TS0_1_D0Digital Input TS0 data0 input (serial mode)
TS0_D3TS0_D[3]Digital Input TS0 data3 input (parallel mode)
57 GPIO25
Digital
Input/Output
General Purpose Input/Output
with Pull Up/Down Resistor
4/8/12/16mA driving strength
TS0_0_CLK Digital Input TS0 clock input (serial mode)
TS0_D2TS0_D[2]Digital Input TS0 data2 input (parallel mode)
56 GPIO24
Digital
Input/Output
General Purpose Input/Output
with Pull Up/Down Resistor
4/8/12/16mA driving strength
TS0_1_VLD Digital Input TS0 valid input (serial mode)
TS0_D1TS0_D[1]Digital Input TS0 data1 input (parallel mode)
55 GPIO23
Digital
Input/Output
General Purpose Input/Output
with Pull Up/Down Resistor
4/8/12/16mA driving strength
TS0_1_SYNC Digital Input TS0 sync input (serial mode)
TS0_D0TS0_D[0]Digital Input TS0 data0 input (parallel mode)
54 GPIO22Digital General Purpose Input/Output
Pin Name Function Name Pin Type Function Pin
Input/Output with Pull Up/Down Resistor
4/8/12/16mA driving strength
UART_TX Digital Output UART Transmit Data Output
FUART_CTS Digital Input Fast UART Receive Data Input
HDMI Transmitter Interface
Pin Name Function Name Pin Type Function Pin
HDMI_SDA HDMI_SDA Digital
Input/Output
HDMI I2C Serial Data Bit100
HDMI_SCL HDMI_SCL Digital Output HDMI I2C Serial Clock101 HDMI_HPD HDMI_HPD Digital Input HDMI Hot Plug Detection99 HDMI_TXCN HDMI_TXCN Analog Output HDMI TX Clock Negative103 HDMI_TXCP HDMI_TXCP Analog Output HDMI TX Clock Positive104 HDMI_TX0N HDMI_TX0N Analog Output HDMI TX D0 Negative105 HDMI_TX0P HDMI_TX0P Analog Output HDMI TX D0 Positive106 HDMI_TX1N HDMI_TX1N Analog Output HDMI TX D1 Negative108 HDMI_TX1P HDMI_TX1P Analog Output HDMI TX D1 Positive109 HDMI_TX2N HDMI_TX2N Analog Output HDMI TX D2 Negative110 HDMI_TX2P HDMI_TX2P Analog Output HDMI TX D2 Positive111 HDMI_CEC HDMI_CEC Digital Input HDMI Consumer Electronics Control98
I2C Interface
Pin Name Function Name Pin Type Function Pin
I2CM0_SDA I2CM0_SDA
Digital
Input/Output
I2C Master Port 0 Serial Data Bit
67 GPIO34
Digital
Input/Output
General Purpose Input/Output
with Pull Up Resistor
4mA driving strength
I2CM0_SCL I2CM0_SCL Digital Output I2C Master Port 0 Serial Clock
66 GPIO33
Digital
Input/Output
General Purpose Input/Output
with Pull Up Resistor
4mA driving strength
I2CM1_SDA I2CM1_SDA
Digital
Input/Output
I2C Master Port 1 Serial Data Bit
63 GPIO32Digital General Purpose Input/Output
Pin Name Function Name Pin Type Function Pin
Input/Output with Pull Up/Down Resistor
4mA driving strength
UART_RX2Digital Input UART Receive Data Input
I2CM1_SCL I2CM1_SCL Digital Output I2C Master Port 1 Serial Clock
64 GPIO31
Digital
Input/Output
General Purpose Input/Output
with Pull Up Resistor
4mA driving strength
UART_TX Digital Output UART Transmit Data Output
Tuner Interface
Pin Name Function Name Pin Type Function Pin IF_AGC IF_AGC Analog Output DVB-C DEMOD IF Gain Control82
DVB_C_IP DVB_C_IP Analog Input DVB-C DEMOD Differential Pair of Input Channel
80
DVB_C_IM DVB_C_IM Analog Input DVB-C DEMOD Differential Pair of Input Channel
81
Serial Flash Interface
Pin Name Function Name Pin Type Function Pin
SPI_CK SPI_CK Digital Output Serial Flash Clock
36 NF_WEZ Digital Output Nand Flash Write Enable
SPI_DI SPI_DI
Digital
Output/Input
Serial Flash Data Input
37 NF_WPZ Digital Output Nand Flash Write Protect
SPI_DO SPI_DO
Digital
Input/Output
Serial Flash Data Output
32 NF_CEZ Digital Output Nand Flash Chip Enable
SPI_CZ SPI_CZ Digital Output Serial Flash Chip Enable
31 NF_REZ Digital Output Nand Flash Read Enable
SPI_CZ1 SPI_CZ1Digital Output Serial Flash Chip Enable
34 GPIO45
Digital
Input/Output
General Purpose Input/Output
with Pull Up Resistor
4/8mA driving strength
NF_CLE Digital Output Nand Flash Command Latch Enable
SPI_WPN SPI_WPN Digital
Output/Input
Serial Flash Write Protection30
Pin Name Function Name Pin Type Function Pin NF_RBZ Digital Input Nand Flash Ready/Busy
SPI_HOLDN SPI_HOLDN
Digital
Output/Input
Serial Flash Hold
35 GPIO44
Digital
Input/Output
General Purpose Input/Output
with Pull Up Resistor
4/8mA driving strength
NF_ALE Digital Output Nand Flash Address Latch Enable
Smartcard Interface
Pin Name Function Name Pin Type Function Pin
SM0_CD SM0_CD Digital Input Smartcard Card-detection
27 EJ_RSTZ Digital Input EJ TAG RSTZ
GPIO8
Digital
Input/Output
General Purpose Input/Output
with Pull Up Resistor
4mA driving strength
SM0_RST SM0_RST Digital Output Smartcard Reset
28 EJ_TDO Digital Output EJ TAG TDO
GPIO9
Digital
Input/Output
General Purpose Input/Output
with Pull Up Resistor
4mA driving strength
SM0_VCC SM0_VCC Digital Output Smartcard VCC Enable
29 EJ_TDI Digital Input EJ TAG TDI
GPIO10
Digital
Input/Output
General Purpose Input/Output
with Pull Up Resistor
4mA driving strength
SM0_IO SM0_IO
Digital
Input/Output
Smartcard Data Input/Output
25 EJ_TMS Digital Input EJ TAG TMS
GPIO6
Digital
Input/Output
General Purpose Input/Output
with Pull Up Resistor
4mA driving strength
SM0_CLK SM0_CLK Digital Output Smartcard Clock
26 EJ_TCK Digital Input EJ TAG TCK
GPIO7
Digital
Input/Output
General Purpose Input/Output
with Pull Up Resistor
Pin Name Function Name Pin Type Function Pin
4mA driving strength
SM0_SWITCH SM0_SWITCH Digital Output Smartcard Switch
24 GPIO5
Digital
Input/Output
General Purpose Input/Output
with Pull Up Resistor
4mA driving strength
UART Interface
Pin Name Function Name Pin Type Function Pin UART_RX UART_RX Digital Input UART Receive Data Input 2 UART_TX UART_TX Digital Output UART Transmit Data Output 3
EPHY Interface
Pin Name Function Name Pin Type Function Pin
EPHY_RN EPHY_RN Analog Input Differential Pair of Receiver Signal Negative
91
EPHY_RP EPHY_RP Analog Input Differential Pair of Receiver Signal Positive92
EPHY_TN EPHY_TN Analog Output Differential Pair of Transmitter Signal Negative
93
EPHY_TP EPHY_TP Analog Output Differential Pair of Transmitter Signal Positive
94
ET_LINK_LED ET_LINK_LED Digital Output Ethernet Link LED output88 ET_SPEED_LED ET_SPEED_LED Digital Output Ethernet Speed LED output89
USB Interface
Pin Name Function Name Pin Type Function Pin
DM_P0 DM_P0Analog
Input/Output
USB Port0 D- Signal with Pull Up/Down
Resistor, Parallel Termination
95
DP_P0 DP_P0Analog
Input/Output
USB Port0 D+ Signal with Pull Up/Down
Resistor, Parallel Termination
96
DM_P1 DM_P1Analog
Input/Output
USB Port1 D- Signal with Pull Up/Down
Resistor, Parallel Termination
48
DP_P1 DP_P1Analog
Input/Output
USB Port1 D+ Signal with Pull Up/Down
Resistor, Parallel Termination
49
Misc. Interface
Pin Name Function Name Pin Type Function Pin XTAL_IN XTAL_IN Analog Input24MHz Crystal Oscillator Input85 XTAL_OUT XTAL_OUT Analog Output24MHz Crystal Oscillator Output86 PWR_CTRL PWR_CTRL Digital Output Power control 1 RESET RESET Digital Input System Reset7 IRIN IRIN Digital Input Infrared Input from IR Receiver 23
Power Pins
Pin Name Function Name Pin Type Function Pin AVDD33_DADC AVDD33_DADC 3.3V Power DMADC Supply79, 83 AVDD33_AUSDM AVDD33_AUSDM 3.3V Power Audio DAC Supply122 AVDD33_IDAC AVDD33_IDAC 3.3V Power Video DAC Supply113
AVDD33_USB _P1 AVDD33_USB
_P1
3.3V Power USB Port Supply50
AVDD33_USB _P0 AVDD33_USB
_P0
3.3V Power USB Port Supply97
AVDD33_HDMIT X AVDD33_HDMIT
X
3.3V Power HDMI Transmitter Supply102
AVDD_PLL AVDD_PLL 3.3V Power PLL Supply18 AVDD33_DMPLL AVDD33_DMPLL 3.3V Power DMPLL Supply84 AVDD33_ETH AVDD33_ETH 3.3V Power ETH Supply90
VDDP VDDP 3.3V Power Digital Input/Output Supply 33, 65, 76, 127
VDDIO_DATA VDDIO_DATA 1.5V Power
(DDR3)
DDR Data Supply19, 21
VDDIO_CMD VDDIO_CMD 1.5V Power
(DDR3)
DDR Command Supply10, 12
VDDIO_DRAM VDDIO_DRAM 1.5V Power
(DDR3)
DRAM Supply11, 22
VDDIO_MCLK VDDIO_MCLK 1.5V Power
(DDR3)
DDR CLK Supply14
VDDIO_LDO VDDIO_LDO 1.5V Power
(DDR3)
DDR LDO Supply15
AVDDL_HDMITX AVDDL_HDMITX V VDD_core HDMI Transmitter Supply107
DVDD_DDR_1.1 V DVDD_DDR_1.1
V
V VDD_core DDR TX Supply16
Pin Name Function Name Pin Type Function Pin
DVDD_DDR_RX_ 1.1V DVDD_DDR_RX_
1.1V
V VDD_core DDR RX Supply17
VDDC VDDC V VDD_core Digital Core Supply 13, 47, 51, 68, 69, 112, 126
GND GND Ground Ground20, 87 No Connection
Pin Name Function
Name
Pin Type Function Pin NC - No connect. Leave this pin floating. 77, 78
ELECTRICAL SPECIFICATIONS
Analog Interface Characteristics
Parameter Min Typ Max Unit VIDEO ANALOG OUTPUT
CVBS/S-Video/YPbPr Output
Output Low Output High
1.3
V
V
AUDIO
Line Driver Output 2.0 V rms SAR ADC Input 0 AVDD_NODIE V HDMI TX Output
Single Ended Output Current 8 10 12 mA Output Leakage Current 0 200 uA Differential Signal Rise Time 75 0.4*Tbit ps Differential Signal Fall Time 75 0.4*Tbit ps Differential Clock Duty Cycle 40 50 60 % Differential Data Jitter 0.3 Tbit DIGITAL INPUTS
Input Voltage, High (V IH) 2 V Input Voltage, Low (V IL) 0.8 V Input Current, High (I IH) -1.0 uA Input Current, Low (I IL) 1.0 uA Input Capacitance 5 pF DIGITAL OUTPUTS
Output Voltage, High (V OH) VDDP-0.1 V Output Voltage, Low (V OL) 0.1 V Note: 1. Specifications subject to change without notice.
2. AVDD_NODIE and VDDP are
3.3V Supply Voltages.
Recommended Operating Conditions
Parameter Symbol Min Typ Max Units 3.3V Supply Voltages V VDD_33 3.13 3.47 V
1.5V Supply Voltages (DDR3) V VDD_15 1.42 1.58 V Core Supply Voltages V VDD_core 1.08 1.12 1.16 V Ambient Operating Temperature T A0 70 °C Junction Temperature T J125 °C
Absolute Maximum Ratings
Parameter Symbol Min Max Units 3.3V Supply Voltages V VDD_33 3.6 V
1.5V Supply Voltages V VDD_15 1.65 V Core Supply Voltages V VDD_core 1.54 V Input Voltage (5V tolerant inputs) V IN5Vtol 5.3 V Input Voltage (non 5V tolerant inputs) V IN V VDD_33V Storage Temperature T STG-40 150 °C Note: 1. Stresses above those listed in Absolute Maximum Ratings may cause permanent damage to the device. This is a stress rating only and does not imply functional operation of the device. Exposure to absolute maximum ratings for extended periods may affect device reliability
2. The final specification of VDD Supply Voltage will depend on final IC test result.
压力变送器说明书
压力变送器说明书-CAL-FENGHAI.-(YICAI)-Company One1
YBY-1 压力变送器 使用说明书 青岛奥博仪表设备有限公司
目录 一.概述……………………………………………… 二.工作原理与特点 (1) 三 .技术指标 (1) 四 .接线及安装 (2) 五. 调整 (5) 六. 注意事项 (6)
一、概述: 本压力变送器是依据《JJG882-2004中华人民共和国国家计量检定规程--压力变送器》,同时以《JB/中华人民共和国机械行业标准DDZ-ZZZ系列电动单元组合仪表力单元平衡式变送器》为产品标准以Ⅲ型电动组合仪表的变送单元,可广泛应用于测量工业领域液体、气体的压力,把被测压力参数值转换成4~20mA标准信号,可与多种仪表相配套。因而可广泛应用于石油、化工、冶金、电站、锅炉、轻工等许多部门。 二、工作原理与特点 1、本变送器的传感元件是扩散硅力敏器件。这种器件是利用集成电路工艺,在晶体硅片上制成敏感压阻,组成惠斯登电桥,作为力电转换的敏感器件。当受到外力作用时,电桥失去平衡。当给桥路加一恒流激励电源时,可以将压力信号线性地转换成毫伏级电压信号,经放大转换变成4~20mA标准信号输出,便于远距离传送。 2、由于本送器采用了扩散硅式力敏器件,使其体积和重量大大减小。不仅外型美观、结构简单,而且各项技术性能稳定可靠,所以安装和维护特别方便,无需现场调试。输出的标准电流信号,实现远距离传输便于用户便用。因此,本变送器是过程控制中的理想仪表。 三、技术指标: 1.量程:0~;0~; 0~60MPa。 2.基本误差:≤% 3.反映时间:<500mS 4.电源:24VDC±5% 5.输出:4~20mADC 6.负载电阻:≤350Ω 7.被测介质温度:-10~60℃ 8.重量:约㎏ 1
压力变送器说明书
一、1151压力变送器工作原理 被测介质的两种压力通入高、低两压力室,作用在δ元件(即敏感元件)的两侧隔离膜片上,通过隔膜片和δ 1151压力变送器原理图 元件内的填充液传到预张紧的测量腊片两侧,测量膜片与两侧绝缘体上的电极各组成一个电容器,在无压力通入或两压力均等时测量膜片处于中间位置,两侧两电容器的电容量相等,当两侧压力不一致时,致使测量膜片产生位移,其位移量和压力差成正比,故两侧电容就不等,通过检测,放大转换成4-2OmA的二线制电流信号。压力交送器和绝对压力交送器的工作原理和差压变送器相同,所不同的是低压室压力是大气压或真空元份结构图见右图 二、电气原理图 1151压力变松电气原理图 三、主要特点 电容式变送器有下列特点 1.品种齐全、精度高、稳定性好,价格比同类进口仪表便宜 2.采用二线制工作方式 3.敏感元件采用固体化结构,小型坚固,抗振能力强 4.主要部件可与1151同类产品进行互换, 5.关键零部件、电子元件及接插件均采用国际上高质量产品。本系列产品可靠性好,质量稳定,故障率少。 6.正迁移可达500%,负迁移可达600%(最小量程时) 7.阻尼可调 电容式变送器品种齐全,用户可按不同需要任意选用,自微差压至大差压,从低压力至高压力、绝对压力、高静压差压。DP/GP型变送器带上各种远传装置后,就成为远传式差压、压力变送器。采用ANSI标准,管道尺寸3",法兰等级150磅(2.5MPa),插入筒式远传装置后,插入筒长度一般
结构尺寸 八、1151变送器典型安装 变送器可以直接安装在测量点处,可以安装在墙上,或者使用安装板(变送器附件)夹拼在2''(约φ50mm)的管道上。 变送器压力容室上的导压连接孔为1/4-18NPT螺纹孔,接头上的导压接孔为1/2-14NPT内锥管螺纹(或M2OXl.5-18外螺纹),根据需要可选择与引压接头1/2-14NPT锥管螺纹的过渡接头。变送器可以轻而易举地从流程1艺管道上拆下,万法是拧下紧固接头的两个螺栓。转动接头,可以改变其接孔的中心距离为5lmm,54mm,57mm三种尺寸。 为了确保接头密封,在固紧时应按下面步骤操作:两只紧固螺栓应交替用板手均匀拧紧,其最后拧紧力距大约为40N.m(29fs-bs),切勿一次拧紧某一只螺栓。有时为了安装上的方便,变送器本体上的压力容室可转动。只要压力容室处于垂直面,则变送器木体的转动不会产生零位的变化。如果压力容室水平安装时(例如在垂直管道上测量流量时),则必须消除由于导压管高度不同而引起的液柱压力的影响。即重新调零位。 九、变送器的型号命名
压力差压变送器技术规格书
压力/差压变送器 技 术 规 范 书
1总则 1.1本规范适项目压力、差压变送器的设计、结构、性能、安装和调试等方面的技术要求。 1.2本规范提供的是最低限度的技术要求,并未规定所有的技术要求和适用标准,投标方应提供一套满足本规范和所列标准要求的高质量标准产品及其相应服务。对国家有关安全、环保等强制性标准,必须满足其要求。 1.3如果投标方未以书面形式对本规范书提出异议,则意味着投标方提供的压力、差压变送器完全符合本技术技术规范和有关工业标准的要求。如有任何异议,都应在投标书中以“对规范书的意见和同规范书的差异”文标题的专门章节中加以详细说明。 1.4本规范书使用的标准如遇与投标方所执行的标准相冲突时,按较高标准执行。 1.5所有正式文件、所附图纸及相互通讯函件,均应使用中文。不论在合同谈判及签约后的工程建设期间,中文是主要的工作语言。部分硬件说明书记图纸可使用英文,但只作为辅助工作语言。 1.6只有招标方有权修改本规范书。经买卖双方协商,最终确定的规范书应作为合同的一个附件,并与合同文件有相同的法律效力。1.7在签订合同后,招标方有权提出因标准、规范和规程发生变化所产生的一些修订要求,具体事项由双方共同协商确定。 1.8卖方应提供不同型式、不同材质、不同规格、不同压力等级的阀组的分项单价报价及产品发生故障时须更换的零部件价格明细。
2设备使用环境 2.1海拔高度:1000米以下 2.2最高温度:85度 2.3最低气温:-19度 2.4相对湿度:≤95% 3技术要求 3.1供应方应明确所供设备的技术参数符合仪表数据表的技术要求并在表述中明确说明技术水平在目前的先进性。所供设备应提供标准和规范要求的检验文件、质检合格证书和相关资料。 3.2供方应提供数据表中所要求的符合质量标准的附件和备品备件,如果有其他需要附件或备品备件,供方应以书面形式在投标书中明确说明,并附详细规格参数、材质及价格明细。 3.3供方应提供技术上成熟先进的设备,不得使用实验性的设备和技术。 3.4设备应按照最新规范和标准进行设计、制造、检验、测试和安装。 3.5除以上要求外,未指定要求的技术参数应由供应商明确表述,但不仅限于此还应满足以下要求: 3.5.1所有变送器信号必须为智能型两线制4-20mA DC 叠加HART 协议信号(HART 版本6.0 或以上)。 3.5.2智能型现场变送器应能够和DCS系统进行通讯,实现远程对现场变送器进行设置、组态和维护。 3.5.3智能型压力和差压变送器应具备非易挥发性存储器。
压力和差压变送器详细详解使用说明书样本
压力和差压变送器详细使用说明 ( 一) 差压变送器原理与使用 本节根据实际使用中的差压变送器主要介绍电容式差压变送器。 1. 差压变送器原理 压力和差压变送器作为过程控制系统的检测变换部分, 将液体、气体或蒸汽的差压(压力)、流量、液位等工艺参数转换成统一的标准信号(如DC4mA~20mA 电流), 作为显示仪表、运算器和调节器的输入信号, 以实现生产过程的连续检测和自动控制。 差动电容式压力变送器由测量部分和转换放大电路组成, 如图1.1所示。 图1.1 测量转换电路
图1.2 差动电容结构差动电容式压力变送器的测量部分常采用差动电容结构, 如图 1.2所示。中心可动极板与两侧固定极板构成两个平面型电容 H C和L C。可动极板与两侧固定极板形成两个感压腔室, 介质压力是经过两个腔室中的填充液作用到中心可动极板。一般采用硅油等理想液体作为填充液, 被测介质大多为气体或液体。隔离膜片的作用既传递压力, 又避免电容极板受损。 当正负压力(差压)由正负压导压口加到膜盒两边的隔离膜片上时, 经过腔室内硅油液体传递到中心测量膜片上, 中心感压膜片产生位移, 使可动极板和左右两个极板之间的间距不相对, 形成差动电容, 若不考虑边缘电场影响, 该差动电容可看作平板电容。差动电容的相对变化值与被测压力成正比, 与填充液的介电常数无关, 从原理上消除了介电常数的变化给测量带来的误差。 2. 变送器的使用 ( 1) 表压压力变送器的方向 低压侧压力口( 大气压参考端) 位于表压压力变送器的脖颈处,
在电子外壳的后面。此压力口的通道位于外壳和压力传感器之间, 在变送器上360°环绕。保持通道的畅通, 包括但不限于由于安装变送器时产生的喷漆, 灰尘和润滑脂, 以至于保证过程通畅。图1.3为低压侧压力口。 图1.3 低压侧压力口 ( 2) 电气接线 ①拆下标记”FIELD TERMINALS”电子外壳。 ②将正极导线接到”PWR/COMN”接线端子上, 负极导线接 到”-”接线端子 上。注意不得将带电信号线与测试端子( test) 相连, 因通电将损坏测试线路中的测试二极管。应使用屏蔽的双绞线以获得最佳的测量效果, 为了保证正确通讯, 应使用24AWG或更高的电缆线。 ③用导管塞将变送器壳体上未使用的导管接口密封。 ④重新拧上表盖。 ( 3) 电子室旋转 电子室能够旋转以便数字显示位于最好的观察位置。旋转时, 先松开壳体旋转固定螺钉。
压力和差压变送器详细详解使用说明书
压力与差压变送器详细使用说明 (一)差压变送器原理与使用 本节根据实际使用中得差压变送器主要介绍电容式差压变送器。 1、差压变送器原理 压力与差压变送器作为过程控制系统得检测变换部分,将液体、气体或蒸汽得差压(压力)、流量、液位等工艺参数转换成统一得标准信号(如DC4mA~20mA 电流),作为显示仪表、运算器与调节器得输入信号,以实现生产过程得连续检测与自动控制。 差动电容式压力变送器由测量部分与转换放大电路组成,如图1、1所示。 图1、1 测量转换电路 图1、2 差动电容结构 差动电容式压力变送器得测量部分常采用差动电容结构,如图1、2所示。中心可动极板与两侧固定极板构成两个平面型电容H C与L C。可动极板与两侧固定极板形成两个感压腔室,介质压力就是通过两个腔室中得填充液作用到中心可动极板。一般采用硅油等理想液体作为填充液,被测介质大多为气体或液体。隔离膜片得作用既传递压力,又避免电容极板受损。 当正负压力(差压)由正负压导压口加到膜盒两边得隔离膜片上时,通过腔室
内硅油液体传递到中心测量膜片上,中心感压膜片产生位移,使可动极板与左右两个极板之间得间距不相对,形成差动电容,若不考虑边缘电场影响,该差动电容可瞧作平板电容。差动电容得相对变化值与被测压力成正比,与填充液得介电常数无关,从原理上消除了介电常数得变化给测量带来得误差。 2、变送器得使用 (1) 表压压力变送器得方向 低压侧压力口(大气压参考端)位于表压压力变送器得脖颈处,在电子外壳得后面。此压力口得通道位于外壳与压力传感器之间,在变送器上360°环绕。保持通道得畅通,包括但不限于由于安装变送器时产生得喷漆,灰尘与润滑脂,以至于保证过程通畅。图1、3为低压侧压力口。 图1、3 低压侧压力口 (2)电气接线 ①拆下标记“FIELD TERMINALS”电子外壳。 ②将正极导线接到“PWR/N”接线端子上,负极导线接到“-”接线端子 上。注意不得将带电信号线与测试端子(test)相连,因通电将损坏测试线路中得测试二极管。应使用屏蔽得双绞线以获得最佳得测量效果,为了保证正确通讯,应使用24AWG或更高得电缆线。 ③用导管塞将变送器壳体上未使用得导管接口密封。 ④重新拧上表盖。 (3)电子室旋转 电子室可以旋转以便数字显示位于最好得观察位置。旋转时,先松开壳体旋转固定螺钉。 3、投运与零点校验 一体化三阀组与差压变送器投入运行时得操作程序: 首先,打开差压变送器上两个排污阀,而后打开平衡阀,再慢慢打开二个截止阀,将导压管内得空气或污
双法兰差压变送器技术规格书及数据表(6台)(1)
兖矿鲁南化工有限公司 技术协议书 双法兰差压变送器 编制: 审核: 审批: 卖方:上海盛凯隆自动化仪表有限公司买方:兖矿鲁南化工有限公司 二○一七年三月
1.总则 1.1 设备名称:双法兰差压变送器 1.2 本技术规格书提出的是最低限度的要求,并未对一切细节做出规定,也未充分引述有关标 准和规范的条文,卖方应保证提供符合本技术规格书和有关最新工业标准的产品。 1.3 所招产品为双法兰变送器,卖方产品必须完全满足水煤浆加压气化工艺的特殊工况。 2. 产品描述 2.1本规格书要求购买变送器共6台。 2.2本变送器要求为进口品牌的产品。品牌限定为罗斯蒙特3051系列变送器。 2.3针对此变送器的重要性及其较苛刻的工况,卖方均要严格按本技术要求及数据表的要求 进行配置。 3.设计依据 3.1此变送器的设计和选型应严格按照协议书的要求,以及买方提出的任何其它技术要求。 3.2环境状况: 年平均气温:13.7℃;极端最高气温:40.4℃;极端最低气温:-21.8℃; 年平均相对湿度:69%; 地区大气压:平均1079mbar; 3.3仪表及所配电气附件防护要求: 防护等级:IP65 防爆等级:ExdII CT4 4.应用标准 仪表安装手册API RP550 仪器仪表包装运输技术条件ZBY003-84 工业仪表模拟信号ISA S50.1 爆炸性环境用防爆电气设备IEC 60079—1998、GB3886 仪表防护IEC 529、GB4208-2000 法兰标准见数据表 铭牌和印记MSS-SP-25 5.技术要求 5.1 卖方所供差压变送器及附件产品必须是全新产品,整体集成供货。
压力差压变送器技术规格书
. 压力/差压变送器 技 术 规 范 书
1总则 1.1本规范适项目压力、差压变送器的设计、结构、性能、安装和调试等方面的技术要求。 1.2本规范提供的是最低限度的技术要求,并未规定所有的技术要求和适用标准,投标方应提供一套满足本规范和所列标准要求的高质量标准产品及其相应服务。对国家有关安全、环保等强制性标准,必须满足其要求。 1.3如果投标方未以书面形式对本规范书提出异议,则意味着投标方提供的压力、差压变送器完全符合本技术技术规范和有关工业标准的要求。如有任何异议,都应在投标书中以“对规范书的意见和同规范书的差异”文标题的专门章节中加以详细说明。 1.4本规范书使用的标准如遇与投标方所执行的标准相冲突时,按较高标准执行。 1.5所有正式文件、所附图纸及相互通讯函件,均应使用中文。不论在合同谈判及签约后的工程建设期间,中文是主要的工作语言。部分硬件说明书记图纸可使用英文,但只作为辅助工作语言。 1.6只有招标方有权修改本规范书。经买卖双方协商,最终确定的规范书应作为合同的一个附件,并与合同文件有相同的法律效力。1.7在签订合同后,招标方有权提出因标准、规范和规程发生变化所产生的一些修订要求,具体事项由双方共同协商确定。 1.8卖方应提供不同型式、不同材质、不同规格、不同压力等级的阀组的分项单价报价及产品发生故障时须更换的零部件价格明细。
2设备使用环境 2.1海拔高度:1000米以下 2.2最高温度:85度 2.3最低气温:-19度 2.4相对湿度:≤95% 3技术要求 3.1供应方应明确所供设备的技术参数符合仪表数据表的技术要求并在表述中明确说明技术水平在目前的先进性。所供设备应提供标准和规范要求的检验文件、质检合格证书和相关资料。 3.2供方应提供数据表中所要求的符合质量标准的附件和备品备件,如果有其他需要附件或备品备件,供方应以书面形式在投标书中明确说明,并附详细规格参数、材质及价格明细。 3.3供方应提供技术上成熟先进的设备,不得使用实验性的设备和技术。 3.4设备应按照最新规范和标准进行设计、制造、检验、测试和安装。 3.5除以上要求外,未指定要求的技术参数应由供应商明确表述,但不仅限于此还应满足以下要求: 3.5.1所有变送器信号必须为智能型两线制4-20mA DC 叠加HART 协议信号(HART 版本6.0 或以上)。 3.5.2智能型现场变送器应能够和DCS系统进行通讯,实现远程对现场变送器进行设置、组态和维护。 3.5.3智能型压力和差压变送器应具备非易挥发性存储器。
压力变送器说明书
鲁制02000060-2A YBY-1 压力变送器 使用说明书青岛奥博仪表设备有限公司
目录 一.概述……………………………………………… 二.工作原理与特点 (1) 三.技术指标 (1) 四.接线及安装 (2) 五. 调整 (5) 六. 注意事项 (6)
一、概述: 本压力变送器是依据《JJG882-2004中华人民共和国国家计量检定规程--压力变送器》,同时以《JB/中华人民共和国机械行业标准DDZ-ZZZ系列电动单元组合仪表力单元平衡式变送器》为产品标准以Ⅲ型电动组合仪表的变送单元,可广泛应用于测量工业领域液体、气体的压力,把被测压力参数值转换成4~20mA标准信号,可与多种仪表相配套。因而可广泛应用于石油、化工、冶金、电站、锅炉、轻工等许多部门。 二、工作原理与特点 1、本变送器的传感元件是扩散硅力敏器件。这种器件是利用集成电路工艺,在晶体硅片上制成敏感压阻,组成惠斯登电桥,作为力电转换的敏感器件。当受到外力作用时,电桥失去平衡。当给桥路加一恒流激励电源时,可以将压力信号线性地转换成毫伏级电压信号,经放大转换变成4~20mA标准信号输出,便于远距离传送。 2、由于本送器采用了扩散硅式力敏器件,使其体积和重量大大减小。不仅外型美观、结构简单,而且各项技术性能稳定可靠,所以安装和维护特别方便,无需现场调试。输出的标准电流信号,实现远距离传输便于用户便用。因此,本变送器是过程控制中的理想仪表。 三、技术指标: 1.量程:0~;0~; 0~60MPa。 2.基本误差:≤% 3.反映时间:<500mS 4.电源:24VDC±5% 5.输出:4~20mADC 6.负载电阻:≤350Ω 7.被测介质温度:-10~60℃ 8.重量:约㎏ 1
压力和差压变送器详细使用说明
压力和差压变送器详细使用说明 (一)差压变送器原理与使用 本节根据实际使用中的差压变送器主要介绍电容式差压变送器。 1. 差压变送器原理 压力和差压变送器作为过程控制系统的检测变换部分,将液体、气体或蒸汽的差压(压力)、流量、液位等工艺参数转换成统一的标准信号(如DC4mA~20mA 电流),作为显示仪表、运算器和调节器的输入信号,以实现生产过程的连续检测和自动控制。 差动电容式压力变送器由测量部分和转换放大电路组成,如图1.1所示。 图1.1 测量转换电路 图1.2 差动电容结构 差动电容式压力变送器的测量部分常采用差动电容结构,如图1.2所示。中心可动极板与两侧固定极板构成两个平面型电容H C和L C。可动极板与两侧固定极板形成两个感压腔室,介质压力是通过两个腔室中的填充液作用到中心可动极板。一般采用硅油等理想液体作为填充液,被测介质大多为气体或液体。隔离膜片的作用既传递压力,又避免电容极板受损。
当正负压力(差压)由正负压导压口加到膜盒两边的隔离膜片上时,通过腔室内硅油液体传递到中心测量膜片上,中心感压膜片产生位移,使可动极板和左右两个极板之间的间距不相对,形成差动电容,若不考虑边缘电场影响,该差动电容可看作平板电容。差动电容的相对变化值与被测压力成正比,与填充液的介电常数无关,从原理上消除了介电常数的变化给测量带来的误差。 2. 变送器的使用 (1)表压压力变送器的方向 低压侧压力口(大气压参考端)位于表压压力变送器的脖颈处,在电子外壳的后面。此压力口的通道位于外壳和压力传感器之间,在变送器上360°环绕。保持通道的畅通,包括但不限于由于安装变送器时产生的喷漆,灰尘和润滑脂,以至于保证过程通畅。图1.3为低压侧压力口。 图1.3 低压侧压力口 (2)电气接线 ①拆下标记“FIELD TERMINALS”电子外壳。 ②将正极导线接到“PWR/COMN”接线端子上,负极导线接到“-”接线端子上。注意不得将带电信号线与测试端子(test)相连,因通电将损坏测试线路中的测试二极管。应使用屏蔽的双绞线以获得最佳的测量效果,为了保证正确通讯,应使用24AWG或更高的电缆线。 ③用导管塞将变送器壳体上未使用的导管接口密封。 ④重新拧上表盖。 (3)电子室旋转 电子室可以旋转以便数字显示位于最好的观察位置。旋转时,先松开壳体旋转固定螺钉。 3. 投运和零点校验
压力变送器说明书
Tel: +86-9 / 86048879 Fax:+86-88074568-808 网址(URL):https://www.360docs.net/doc/f818492861.html, Email:zhekongkeji163. 品质铸造浙控 科技成就梦想! 技术说明书地址:中国·浙江省杭州市西湖区三墩镇金渡北路88号邮编:310003 Add:88 Jindu North Road Sandun, Xihu,Hangzhou,Zhejiang,China : +86-9 / 86048879 传真:+86-8-808 . . 资.料. ..
杭州浙控科技有限公司 尊敬的客户: 衷心感谢您使用我单位制造生产的压力变送器、液位变送器。您在实际操作仪表的过程中,一定有新的发现和更切合实际的使用方法,您对仪表的外型、结构、功能也会有独到的体会,我们期盼您直言不讳,提出宝贵意见,我们将把您的意见转化为动力投入到完善仪器、改进服务等具体行动中去。 客户服务部 压力变送器 一、用途 本产品广泛用于石油、化工、冶金、电力、轻工、建材、科研等企事业单位,实现对流体压力的测量,可适用于工业测量的各种场合及介质,是工业自动化领域理想的压力测量仪表。 二、特点 1、选用具有国际先进水平的传感器,配合高精度的元器件,经严格的工艺过程装配而成,因此在使用温度范围内非线性小,长期稳定性好。 2、可靠的机械保护IP65和防爆保护dⅡBT4/T6,适用于各种恶劣环境。 3、可用于测量粘稠、结晶及腐蚀性介质。 4、4~20mADC标准电流信号输出,二线制工作。 5、体积小,重量轻,安装、调试、使用方便。 三、技术指标 ◆被测介质:与316不锈钢兼容的液体、气体、蒸汽 ◆测量范围:-95KPa~40MPa ◆输出:4~20mADC二线制 ◆准确度:0.2%FS,0.5%FS . . 资.料. ..