美国杜邦POM 500P物性数据表
POM 美国杜邦 525GR
POM 美国杜邦 525GR美国杜邦公司物性数据①原料描述部分规格级别：注塑级外观颜色：---用途概述：需要较高刚性的机械零件备注说明：中粘性。
25%玻纤增强级有特高刚性及强度。
POM 美国杜邦 525GR物性表资料由金橙塑胶提供T e L: 1 5 2 0 7 6 9 2 6 2 0②原料技术数据性能项目试验条件[状态]测试方法测试数据数据单位物理性能密度--- ISO 1183 1580 kg/m3吸水率平衡于50%相对湿度ISO 62 1.3 %机械性能屈服点应力5mm/min 23℃ ISO 527-1/2 140 Mpa 屈服点应变5mm/min 23℃ ISO 527-1/2 3 % 拉伸系数1mm/min 23℃ ISO 527-1/2 9500 Mpa 弯曲模量--- ISO 178 8000 Mpa 埃佐缺口冲击试验23℃ ISO 180/1A 9 KJ/m2夏比缺口冲击试验23℃ 179/1eA 8 KJ/m2热性能热变形温度0.45MPa ISO 75-1/-2 176 ℃ 热变形温度 1.8MPa ISO 75-1/-2 172 ℃ 融点--- ISO 3146C 178 ℃如果对POM 美国杜邦525GR方面还有什么疑问,请与我们详谈!1:美国杜邦系列(聚甲醛)POM:美国杜邦POM 100AF 20%铁氟龙增强合金低磨耗高粘度高韧性POM美国杜邦POM 500AF 20%TEFLON3纤维增强高流动低磨耗聚甲醛美国杜邦POM 100P 注塑级高粘度高韧性POM美国杜邦POM 500P 高流动性表面经润滑树脂美国杜邦POM 900P 高流动性低黏度表面经润滑树脂厨卫网美国杜邦POM 1700P 超高流动级POM 超低粘度均一物性美国杜邦POM 100T 坚韧高粘性美国杜邦POM 100ST 高黏度表面经润滑,超强韧性聚甲醛树脂美国杜邦POM 500T 低磨耗高流动POM美国杜邦POM 100 高粘度，具有最坚韧的硬度，优良的热稳定性美国杜邦POM 500 高流动高抗冲抗蠕变美国杜邦POM 500CL 高流动抗磨耗POM美国杜邦POM 500AL 高流动抗磨耗级美国杜邦POM 107 强度、刚度、热稳定性能好、硬度好。
杜邦物性表-POM DELRIN500TNC010
DuPont™ Delrin®acetal resinDelrin® 500T NC010Delrin® 500T NC010 is a toughened, medium viscosity acetal homopolymer resin with impact resistance similar to Delrin® 100. It can be used in parts requiring noise reduction.Property Test Method Units ValueIdentificationResin Identification ISO 1043POM-IPart Marking Code ISO 11469>POM-I< MechanicalYield Stress ISO 527MPa (kpsi)54 (7.8)Yield Strain ISO 527%20Strain at Break ISO 527%50mm/min>50Nominal Strain at Break ISO 527%35Tensile Modulus ISO 527MPa (kpsi)2300 (334)Tensile Creep Modulus ISO 899MPa (kpsi)1h2300 (334)1000h1150 (167)Flexural Modulus ISO 178MPa (kpsi)2100 (305)Flexural Stress ISO 178MPa (kpsi)@ 3.5% Strain60 (8.7)Notched Charpy Impact Strength ISO 179/1eA kJ/m2-30°C (-22°F)923°C (73°F)14Unnotched Charpy Impact Strength ISO 179/1eU kJ/m2-30°C (-22°F)33023°C (73°F)NBContact DuPont for Material Safety Data Sheet, general guides and/or additional information about ventilation, handling, purging, drying, etc.ISO Mechanical properties measured at 4.0mm, ISO Electrical properties measured at 2.0mm, and all ASTM properties measured at 3.2mm.Test temperatures are 23°C unless otherwise stated.The DuPont Oval Logo, DuPont™, The miracles of science™ and Delrin® are trademarks or registered trademarks of DuPont Company. Copyright© 2005.060130/060130 The information provided in this data sheet corresponds to our knowledge on the subject at the date of its publication. This information may be subject to revision as new knowledge and experience becomes available. The data provided fall within the normal range of product properties and relate only to the specific material designated;these data may not be valid for such material used in combination with any other materials, additives or pigments or in any process, unless expressly indicated otherwise.The data provided should not be used to establish specification limits or used alone as the basis of design; they are not intended to substitute for any testing you may need to conduct to determine for yourself the suitability of a specific material for your particular purposes. Since DuPont cannot anticipate all variations in actual end-useconditions DuPont makes no warranties and assumes no liability in connection with any use of this information. Nothing in this publication is to be considered as alicense to operate under or a recommendation to infringe any patent rights. DuPont advises you to seek independent counsel for a freedom to practice opinion on the intended application or end-use of our products. Caution: Do not use this product in medical applications involving permanent implantation in the human body.For other medical applications see "DuPont Medical Caution Statement", H-50102.Delrin® 500T NC010Property Test Method Units ValueThermalDeflection Temperature ISO 75f °C (°F)0.45MPa146 (295)1.80MPa78 (172)Melting Temperature ISO 11357-1/-3 °C (°F)10°C/min178 (352)CLTE, Normal ISO 11359-1/-2E-4/C (E-4/F)-40 - 23°C (-40 - 73°F) 1.1 (0.61)23 - 55°C (73 - 130°F) 1.2 (0.66)55 - 100°C (130 - 212°F) 1.6 (0.89)CLTE, Parallel ISO 11359-1/-2E-4/C (E-4/F)-40 - 23°C (-40 - 73°F) 1.1 (0.61)23 - 55°C (73 - 130°F) 1.3 (0.72)55 - 100°C (130 - 212°F) 1.31 (0.73)Vicat Softening Temperature ISO 306 °C (°F)50N139 (282) RheologicalMelt Mass-Flow Rate ISO 1133g/10 min190°C, 2.16kg12ElectricalSurface Resistivity IEC 60093ohm1E15Relative Permittivity IEC 602501E2 Hz 3.61E6 Hz 3.6Volume Resistivity IEC 60093ohm m>1E13Dissipation Factor IEC 60250E-41E6 Hz160CTI IEC 60112V600Contact DuPont for Material Safety Data Sheet, general guides and/or additional information about ventilation, handling, purging, drying, etc.ISO Mechanical properties measured at 4.0mm, ISO Electrical properties measured at 2.0mm, and all ASTM properties measured at 3.2mm.Test temperatures are 23°C unless otherwise stated.The DuPont Oval Logo, DuPont™, The miracles of science™ and Delrin® are trademarks or registered trademarks of DuPont Company. Copyright© 2005.060130/060130 The information provided in this data sheet corresponds to our knowledge on the subject at the date of its publication. This information may be subject to revision as new knowledge and experience becomes available. The data provided fall within the normal range of product properties and relate only to the specific material designated;these data may not be valid for such material used in combination with any other materials, additives or pigments or in any process, unless expressly indicated otherwise.The data provided should not be used to establish specification limits or used alone as the basis of design; they are not intended to substitute for any testing you may need to conduct to determine for yourself the suitability of a specific material for your particular purposes. Since DuPont cannot anticipate all variations in actual end-useconditions DuPont makes no warranties and assumes no liability in connection with any use of this information. Nothing in this publication is to be considered as alicense to operate under or a recommendation to infringe any patent rights. DuPont advises you to seek independent counsel for a freedom to practice opinion on the intended application or end-use of our products. Caution: Do not use this product in medical applications involving permanent implantation in the human body.For other medical applications see "DuPont Medical Caution Statement", H-50102.Delrin® 500T NC010Property Test Method Units ValueFlammabilityFlammability Classification IEC 60695-11-100.75mm HBFlammability Classification UL940.75mm HBOxygen Index ISO 4589-1/-2%23High Amperage Arc Ignition Resistance UL 746A arcs0.75mm200Hot Wire Ignition UL 746A s0.75mm81.5mm113.0mm15 Temperature IndexRTI, Electrical UL 746B°C0.75mm105RTI, Impact UL 746B°C0.75mm85RTI, Strength UL 746B°C0.75mm85OtherDensity ISO 1183kg/m3 (g/cm3)1380 (1.38)Hardness, Rockwell ISO 2039/2Scale M79Scale R117Water Absorption ISO 62, Similar to%Equilibrium 50%RH0.21Saturation, immersed0.82Molding Shrinkage ISO 294-4%Normal, 2.0mm 1.6Parallel, 2.0mm 1.7Contact DuPont for Material Safety Data Sheet, general guides and/or additional information about ventilation, handling, purging, drying, etc.ISO Mechanical properties measured at 4.0mm, ISO Electrical properties measured at 2.0mm, and all ASTM properties measured at 3.2mm.Test temperatures are 23°C unless otherwise stated.The DuPont Oval Logo, DuPont™, The miracles of science™ and Delrin® are trademarks or registered trademarks of DuPont Company. Copyright© 2005.060130/060130 The information provided in this data sheet corresponds to our knowledge on the subject at the date of its publication. This information may be subject to revision as new knowledge and experience becomes available. The data provided fall within the normal range of product properties and relate only to the specific material designated;these data may not be valid for such material used in combination with any other materials, additives or pigments or in any process, unless expressly indicated otherwise.The data provided should not be used to establish specification limits or used alone as the basis of design; they are not intended to substitute for any testing you may need to conduct to determine for yourself the suitability of a specific material for your particular purposes. Since DuPont cannot anticipate all variations in actual end-useconditions DuPont makes no warranties and assumes no liability in connection with any use of this information. Nothing in this publication is to be considered as alicense to operate under or a recommendation to infringe any patent rights. DuPont advises you to seek independent counsel for a freedom to practice opinion on the intended application or end-use of our products. Caution: Do not use this product in medical applications involving permanent implantation in the human body.For other medical applications see "DuPont Medical Caution Statement", H-50102.Delrin® 500T NC010Property Test Method Units ValueProcessingMelt Temperature Range °C (°F)200-210 (390-410)Melt Temperature Optimum °C (°F)205 (400)Mold Temperature Range °C (°F)40-60 (100-140)Mold Temperature Optimum °C (°F)50 (122)Drying Time, Dehumidified Dryer h2-4Drying Temperature °C (°F)80 (175)Processing Moisture Content%<0.05Hold Pressure Range MPa (kpsi)60-80 (9-12)Contact DuPont for Material Safety Data Sheet, general guides and/or additional information about ventilation, handling, purging, drying, etc.ISO Mechanical properties measured at 4.0mm, ISO Electrical properties measured at 2.0mm, and all ASTM properties measured at 3.2mm.Test temperatures are 23°C unless otherwise stated.The DuPont Oval Logo, DuPont™, The miracles of science™ and Delrin® are trademarks or registered trademarks of DuPont Company. Copyright© 2005.060130/060130 The information provided in this data sheet corresponds to our knowledge on the subject at the date of its publication. This information may be subject to revision as new knowledge and experience becomes available. The data provided fall within the normal range of product properties and relate only to the specific material designated;these data may not be valid for such material used in combination with any other materials, additives or pigments or in any process, unless expressly indicated otherwise.The data provided should not be used to establish specification limits or used alone as the basis of design; they are not intended to substitute for any testing you may need to conduct to determine for yourself the suitability of a specific material for your particular purposes. Since DuPont cannot anticipate all variations in actual end-useconditions DuPont makes no warranties and assumes no liability in connection with any use of this information. Nothing in this publication is to be considered as alicense to operate under or a recommendation to infringe any patent rights. DuPont advises you to seek independent counsel for a freedom to practice opinion on the intended application or end-use of our products. Caution: Do not use this product in medical applications involving permanent implantation in the human body.For other medical applications see "DuPont Medical Caution Statement", H-50102.。
POM赛钢
聚甲醛）（赛钢~特灵）英文名称：Polyoxymethylene(Polyformaldehyde)POM（聚甲醛树脂）定义：聚甲醛是一种没有侧链、高密度、高结晶性的线型聚合物。
按其分子链中化学结构的不同，可分为均聚甲醛和共聚甲醛两种。
两者的重要区别是：均聚甲醛密度、结晶度、熔点都高，但热稳定性差，加工温度范围窄（约10℃），对酸碱稳定性略低；而共聚甲醛密度、结晶度、熔点、强度都较低，但热稳定性好，不易分解，加工温度范围宽（约50℃），对酸碱稳定性较好。
是具有优异的综合性能的工程塑料。
有良好的物理、机械和化学性能，尤其是有优异的耐摩擦性能。
俗称赛钢或夺钢，为第三大通用塑料。
适于制作减磨耐磨零件，传动零件，以及化工，仪表等零件。
一般性能聚甲醛是一种表面光滑、有光泽的硬而致密的材料，淡黄或白色，薄壁部分呈半透明。
燃烧特性为容易燃烧，离火后继续燃烧，火焰上端呈黄色，下端呈蓝色，发生熔融滴落，有强烈的刺激性甲醛味、鱼腥臭。
聚甲醛为白色粉末，一般不透明，着色性好，比重1.41-1.43克/立方厘米，成型收缩率1.2-3.0%，成型温度170-200℃，干燥条件80-90℃2小时。
POM 的长期耐热性能不高，但短期可达到160℃，其中均聚POM短期耐热比共聚POM高10℃以上，但长期耐热共聚POM反而比均聚POM高10℃左右。
可在-40℃～100℃温度范围内长期使用。
POM极易分解，分解温度为280度，分解时有刺激性和腐蚀性气体发生。
故模具钢材宜选用耐腐蚀性的材料制作。
力学性能POM强度、刚度高，弹性好，减磨耐磨性好。
其力学性能优异，比强度可达50.5MPa，比刚度可达2650MPa，与金属十分接近。
POM的力学性能随温度变化小，共聚POM比均聚POM 的变化稍大一点。
POM的冲击强度较高，但常规冲击不及ABS和PC；POM对缺口敏感，有缺口可使冲击强度下降90%之多。
POM的疲劳强度十分突出，10交变载荷作用后，疲劳强度可达35MPa，而PA和PC仅为28MPa。
POM 100P物性表
• 电线电缆应用
• 紧固件
• 铸造薄膜
RoHS 合规性
• 联系制造商
外观
• 自然色
加工方法
• 挤出 • 片材挤出成型
• 型材挤出成型 • 注射成型
• 铸造薄膜
多点数据
• Isothermal Stress vs. Strain (ISO 11403-1)
• Shear Modulus vs. Temperature • Viscosity vs. Shear Rate (ISO
.
Delrin® 100P NC010
ACETAL RESIN DuPont Performance Polymers
机械性能 拉伸模量 -40°C 2 23°C 2 100°C 2 23°C 抗张强度 屈服, -40°C 2 屈服, 23°C 2 屈服, 100°C 2 屈服, 23°C -40°C 2 23°C 2 100°C 2 伸长率 屈服, -40°C 2 屈服, 23°C 2 屈服, 100°C 2 屈服, 23°C 断裂, -40°C 2 断裂, 23°C 2 断裂, 100°C 2 断裂, 23°C 断张率 (23°C) 拉伸蠕变模量 1 hr 1000 hr 弯曲模量 -40°C 23°C 100°C 23°C 弯曲强度 5.0% 应变, 23°C 3.5% 应变, 23°C 剪切强度 (23°C)
2012年2月11日 测试方法 UL 746
UL 746
UL 746
UL 746
4/4
.
Copyright © 2012 - IDES - The Plastics Web ® | 15899928820
额定值 单位制 80.0 °C
POM料明细
POM料明细1供应塑胶原料POM美国杜邦100P高粘度2供应塑胶原料POM美国杜邦100T坚韧级高粘性3供应塑胶原料POM美国杜邦111P坚韧级高粘性抗水解4供应塑胶原料POM美国杜邦100TL加铁氟龙1.5% 高粘度5供应塑胶原料POM美国杜邦500AF加铁氟龙20% 高粘度6供应塑胶原料POM美国杜邦100ST超韧级7供应塑胶原料POM美国杜邦500P高粘度8供应塑胶原料POM美国杜邦900P高粘度9供应塑胶原料POM美国杜邦500CL耐磨级10供应塑胶原料POM美国杜邦500AL高粘度11供应POM美国杜邦500T超韧级12供应POM美国杜邦107UV抗紫外线13供应POM美国杜邦525GR玻纤25%增强中粘性14供应POM美国杜邦527UV抗紫外线15供应POM美国杜邦1700P尺寸稳定性低粘度16供应POM美国杜邦570玻纤20%增强高刚性低翘曲17供应POM日本宝理M25-44标准级高粘度18供应POM日本宝理M25-04挤压级19供应POM日本宝理M90-45耐候级20供应POM日本宝理NW-02高滑动21供应POM日本宝理GH-25玻纤25%增强高刚性高强度22供应POM日本宝理GH-25D玻纤25%增强高强度高刚性高流动性23供应POM日本宝理KT-20无机物填充耐磨损24供应POM日本宝理GB-25玻璃25供应POM日本宝理SX-35质软消音26供应POM日本宝理GH-20玻纤增强高强度高刚性27供应POM日本宝理EB-20防静电28供应POM日本宝理M270-48防静电高流动性29供应POM日本旭化成4013A耐候级抗紫外线30供应POM日本宝理M270高流动性短周期供应POM日本宝理M90-48防静电31供应POM日本宝理GH-25玻纤25%增强高强度高刚性32供应POM日本宝理SW-01特殊润滑剂高性能高滑动33供应POM日本宝理SW-41高滑动高刚性34供应POM日本宝理GH-20玻纤20%增强高强度高刚性35供应POM日本宝理TR-20无机物增强高刚性低翘曲36供应POM日本宝理AW-02高粘度低摩擦37供应POM日本宝理GH-10碳纤维增强导电耐摩擦磨耗38供应POM日本宝理EB-08抗静电导电39供应POM日本宝理EW-02抗静电导电珠增强低翘曲 40.供应POM杜邦-旭化成(张家港)通用级4520、7520;525GR,570(强耐特),AD750;41供应POM台丽钢一般级FM090,FM270,FM130,FM350,FM450,FM550;42.供应POM南通宝泰菱F20-02,F20-30,M90-44;43.供应POM深圳杜邦100P，500P;44.供应POM云南云天化M90,M270;45.供应POM德国赫斯特C52021 MT24U01.46供应POM韩国工程F20-03,F20-02,F30-03,FG20-25;47供应POM韩国科隆K300,K700;优点：1、具高机械强度和刚性;2、最高的疲劳强度;3、环境抵抗性、耐有机溶剂性佳;4、耐反覆冲击性强;5、广泛的使用温度范围(-40℃~120℃);6、良好的电气性质;7、复原性良好;8、具自已润滑性、耐磨性良好;9、尺寸安定性优。
pom美国杜邦500p
pom美国杜邦500p美国杜邦公司物性数据①原料描述部分规格级别：注塑级外观颜色：---用途概述：一般机械零件、齿轮、拉炼、凸轮。
有素材可供机械加工。
备注说明：一般用途，表面经润滑树脂，有优异的加工成型特性。
均一良好的特性。
pom美国杜邦500p物性表资料由金橙塑胶提供T e L: 1 5 2 0 7 6 9 2 6 2 0②原料技术数据性能项目试验条件[状态] 测试方法测试数据数据单位物理性能比重--- ASTM D-792 1.42 --- 吸水量24小时浸渍ASTM D-570 0.25 % 吸水量50%相对湿度ASTM D-570 0.22 % 吸水量浸渍平衡点ASTM D-570 0.90 % 模收缩--- --- 2.2-2.4 %机械性能洛氏硬度--- ASTM D-785 94 M scale 洛氏硬度--- ASTM D-785 120 R scale 拉伸强度-55℃ ASTM D-638 101 MPa拉伸强度23℃ ASTM D-638 69 MPa拉伸强度70℃ ASTM D-638 48 MPa拉伸强度100℃ ASTM D-638 36 MPa拉伸强度122℃ ASTM D-638 26 MPa破裂点拉伸变形量-55℃ ASTM D-638 15 %破裂点拉伸变形量23℃ ASTM D-638 35 %破裂点拉伸变形量70℃ ASTM D-638 220 %破裂点拉伸变形量100℃ ASTM D-638 >260 %破裂点拉伸变形量122℃ ASTM D-638 >260 %弹性系数23℃ ASTM D-638 3360 MPa挠曲系数-55℃ ASTM D-790 4530 MPa挠曲系数23℃ ASTM D-790 3090 MPa挠曲系数70℃ ASTM D-790 1720 MPa挠曲系数100℃ ASTM D-790 1030 %挠曲系数122℃ ASTM D-790 755 MPa挠曲变形强度23℃ ASTM D-790 97 MPa压缩应力23℃,1%变形ASTM D-695 35 MPa压缩应力23℃,10%变形ASTM D-695 123 MPa 抗剪强度23℃ ASTM D-732 66 MPa挠曲疲劳忍耐限度50%RH,23℃,106周期ASTM D-671 31 MPa负载变形量140kg/cm2,50℃ ASTM D-621 0.5 % 抗拉伸冲击强度长试片23℃ ASTM D-1822 420 kj/m2 IZOD冲击试验无缺口23℃ ASTM D-256 2160 j/m IZOD冲击试验缺口-40℃ ASTM D-256 66 j/m IZOD冲击试验23℃ ASTM D-256 81 j/m电气性能抗电弧 3.1mm ASTM D-495 220 sec 介电强度瞬间Shorttime(2.3mm)ASTM D-149 19.7 kv/mm 容积电阻率23℃,0.2%含水量A STM D-257 1×1015Ω.cm 介电常数50%RH,23℃,102～106HzASTM D-150 3.7 Ω.cm 介电因数50%RH,23℃,106Hz ASTM D-150 0.005 ---热性能线性热膨胀系数60～104℃ ASTM D-696 13.7 10-5m/m℃ 线性热膨胀系数104～160℃ ASTM D-696 14.9 10-5m/m℃ 自燃性--- UL-94 HB ---热畸变温度 1.8MPa ASTM D-648 136 ℃热畸变温度0.5MPa ASTM D-648 172 ℃熔点--- ASTM D-2133 175 ℃热传导系数--- --- 0.37 W/mk线性热膨胀系数-40～29℃ ASTM D-696 10.4 10-5m/m℃ 线性热膨胀系数29～60℃ ASTM D-696 12.2 10-5m/m℃如果对pom美国杜邦500p方面还有什么疑问,请与我们详谈!1:美国杜邦系列(聚甲醛)POM:美国杜邦POM 100AF 20%铁氟龙增强合金低磨耗高粘度高韧性POM美国杜邦POM 500AF 20%TEFLON3纤维增强高流动低磨耗聚甲醛美国杜邦POM 100P 注塑级高粘度高韧性POM美国杜邦POM 500P 高流动性表面经润滑树脂美国杜邦POM 900P 高流动性低黏度表面经润滑树脂厨卫网美国杜邦POM 1700P 超高流动级POM 超低粘度均一物性美国杜邦POM 100T 坚韧高粘性美国杜邦POM 100ST 高黏度表面经润滑,超强韧性聚甲醛树脂美国杜邦POM 500T 低磨耗高流动POM美国杜邦POM 100 高粘度，具有最坚韧的硬度，优良的热稳定性美国杜邦POM 500 高流动高抗冲抗蠕变美国杜邦POM 500CL 高流动抗磨耗POM美国杜邦POM 500AL 高流动抗磨耗级美国杜邦POM 107 强度、刚度、热稳定性能好、硬度好。
POM食品级
食品级POM U10-01 日本宝理塑料有限公司物性数据①原料描述部分暂无此原料描述部分┄②原料技术数据性能项目试验条件[状态]测试方法测试数据数据单位物理性能比重--- ASTM D-792 1.41 ---机械性能拉伸强度--- ASTM D-638 60 MPa 伸长率--- ASTM D-638 45 % 弯曲强度--- ASTM D-790 96 MPa 弯曲模量--- ASTM D-790 2380 MPa艾氏冲击强度缺口侧反缺口侧带缺口带缺口ASTM D-256ASTM D-25663760J/mJ/m电气性能介电穿击强度短时间实验：2mmtASTM D-149 24 MV/m 体积电阻系数3mmt ASTM D-257 1×1014Ω.CM热性能线膨胀系数室温--- 10 ×10-5°C 热变形温度 1.82Mpa ASTM D-648 110 °C阻燃性--- UL 94 HB --- Tel: 152________0769_______26201:美国杜邦系列(聚甲醛)POM:美国杜邦POM 100AF 20%铁氟龙增强合金低磨耗高粘度高韧性POM美国杜邦POM 500AF 20%TEFLON3纤维增强高流动低磨耗聚甲醛美国杜邦POM 100P 注塑级高粘度高韧性POM 美国杜邦POM 500P 高流动性表面经润滑树脂美国杜邦POM 900P 高流动性低黏度表面经润滑树脂厨卫网美国杜邦POM 1700P 超高流动级POM 超低粘度均一物性美国杜邦POM 100T 坚韧高粘性美国杜邦POM 100ST 高黏度表面经润滑,超强韧性聚甲醛树脂美国杜邦POM 500T 低磨耗高流动POM美国杜邦POM 100 高粘度，具有最坚韧的硬度，优良的热稳定性美国杜邦POM 500 高流动高抗冲抗蠕变美国杜邦POM 500CL 高流动抗磨耗POM美国杜邦POM 500AL 高流动抗磨耗级美国杜邦POM 107 强度、刚度、热稳定性能好、硬度好。
POM 500P物性表
101
MPA
拉伸强度
23℃
ASTM D-638
69
MPa
拉伸强度
70℃
ASTM D-638
48
MPa
拉伸强度
100℃
ASTM D-638
36
MPa
拉伸强度
122℃
ASTM D-638
26
MPa
破裂点拉伸变形量
-55℃
ASTM D-638
15
%
破裂点拉伸变形量
23℃
ASTM D-638
MPa
挠曲系数
70℃
ASTM D-790
1720
MPa
挠曲系数
100℃
ASTM D-790
1030
%
挠曲系数
122℃
ASTM D-790
755
MPa
挠曲变形强度
23℃
ASTM D-790
97
MPa
压缩应力
23℃,1%变形
ASTM D-695
35
MPa
压缩应力
23℃,10%变形
ASTM D-695
123
MPa
抗剪强度
23℃
ASTM D-732
66
MPa
挠曲疲劳忍耐限度
50%RH,23℃,106周期
ASTM D-671
31
MPa
负载变形量
140kg/cm2,50℃
ASTM D-621
0.5
%
抗拉伸冲击强度
长试片23℃
ASTM D-1822
420
kj/பைடு நூலகம்2
IZOD冲击试验
无缺口23℃
- 1、下载文档前请自行甄别文档内容的完整性，平台不提供额外的编辑、内容补充、找答案等附加服务。
- 2、"仅部分预览"的文档,不可在线预览部分如存在完整性等问题,可反馈申请退款(可完整预览的文档不适用该条件!)。
- 3、如文档侵犯您的权益，请联系客服反馈,我们会尽快为您处理(人工客服工作时间：9:00-18:30)。
ASTM D256/ISO 179
kg·cm/cm(J/M)ft·lb/in
Charpy冲击强度
23℃（缺口）
ASTM D256/ISO 179
kg·cm/cm(J/M)ft·lb/in
-30℃（缺口）
ASTM D256/ISO 179
kg·cm/cm(J/M)ft·lb/in
23℃（无缺口）
155
℃（℉）
熔点
-
178
℃（℉）
燃烧性（率）
UL94
线性膨胀系数
ASTM D696/ISO 11359
mm/mm.℃
电气性能
介电常数
100HZ
ASTM D150/IEC 60250
1MHZ
ASTM D150/IEC 60250
体积电阻率
ASTM D257/IEC 60093
Ω.cm
表面电阻率
ASTM D257/IEC 60093
拉伸屈服伸长率(延伸率)
ASTM D638/ISO 527
40
%
拉伸断裂伸长率(延伸率)
ASTM D638/ISO 527
30
%
弯曲模量(弯曲弹性率)
ASTM D790/ISO 178
2900
kg/cm²(MPa)[Lb/in2]
弯曲强度
ASTM D790/ISO 178
80
kg/cm²(MPa)[Lb/in2]
用途
本文档由东莞市宇灵塑胶原料提供：聚甲醛
洛氏硬度
ASTM D785
R-120
IZOD缺口冲击强度
1/4" 23℃
ASTM D256/ISO 179
kg·cm/cm(J/M)ft·lb/in
1/4" -30℃
ASTM D256/ISO 179
kg·cm/cm(J/M)ft·lb/in
1/8" 23℃
ASTM D256/ISO 179
kg·cm/cm(J/M)ft·lb/in
1.00E
Ω
耐电弧性
ASTM D495/IEC 60112
加工条件
干燥条件
加工温度
射嘴
℃
料筒前段
℃
料筒中段
℃
料筒后段
℃
熔体温度
℃
模具温度
℃
压力
注塑压力
Mpa
保压压力
Mpa
背压
Mpa
螺杆转速
rpm
其他
备注
一般用途，表面经润滑树脂，有优异的加工成型特性。均一良好的特性。有素材可供机械加工。
美国杜邦POM500P物性数据表
性能项目
测试条件
测试方法
数值/描述
单位
机械性能
拉伸强度(引张强度)
ASTM D638/ISO 527
70
kg/cm²(MPa)[Lb/in2]
断裂伸长率
ASTM D638/ISO 527
%
拉伸模量
ASTM D638/ISO 527
kg/cm²(MPa)[Lb/in2]
ASTM D256/ISO 179
kg·cm/cm(J/M)ft·lb/in
-30℃（无缺口）
ASTM D256/ISO 179
kg·cm/cm(J/M)ft·lb/in
物性性能
比重（密度）
ASTM D792/ISO 1183
成型收缩率
ASTM D955
1420
%
熔融指数（流动系数）
200℃/5kg
ASTM D1238/ISO 1133
g/10min
220℃/10kg
ASTM D1238/ISO 1133
g/10min
吸水率23℃/24H
ASTM D570/ISO 62
%
热性能
热变形温度
退火
ASTM D648/ISO 75
℃（℉）
未退火
ASTM D648/ISO 75
℃（℉）
维卡软化点
ASTM D1525/ISO R306