南京苏富德压缩机说明书
螺杆式制冷压缩机使用说明书
螺杆式制冷压缩机组使用说明1.概述1.1产品特点、用途及使用条件螺杆式制冷压缩机组的主要特点是：排气温度低，可以在大压力比下单机运行；容积效率高；易损件少，运转周期长，使用安全可靠；振动小，运转平稳；能量可以无级调节等。
其使用条件是：冷凝温度：≤43℃蒸发温度：-40~+5℃排气温度：≤105℃喷油温度：25~65℃喷油压力：高于排气压力0.15~0.3MPa1.2产品型号的组成及其代表意义，型号有大写汉语拼音字母和数字组成：图1螺杆式制冷压缩机组命名方式2.螺杆式制冷压缩机组的组成及工作原理螺杆式制冷压缩机组包括：螺杆式制冷压缩机、气路系统、油路系统和控制系统，这些设备（除启动柜之外）装在同一公共底座上，构成机组。
气路系统包括：吸气截止阀、吸气过滤阀、吸气止回阀、排气止回阀、排气截止阀等。
油路系统包括：高效油分离器、油冷却器、油粗过滤器、油泵、油精过滤器、恒压阀、回油过滤器等。
控制系统包括：启动柜、控制台。
典型螺杆式制冷压缩机组流程图见附图1（液氨冷却）2.1螺杆式制冷压缩机螺杆式制冷压缩机是回转式容积型压缩机，依靠气体进入机体后体积的缩小室气体密度急剧增加而使气态制冷剂压力升高。
螺杆式制冷压缩机的机体内装有两只相互啮合的平行转子-----阳转子和阴转子。
具有凸齿的转子为阳转子，通常它与原动机连接，功率由此输入。
具有凹齿的转子称为阴转子。
当阳转子转动时，两转子的齿部相互插入到对方的齿槽内，随着转子的旋转，插入的长度越来越大，容纳气体槽的容积越来越小，从而达到压缩气体制冷剂的目的。
在阴、阳转子的下部，装有一个由油缸内油活塞带动的能量调节滑阀，由电磁（或手动）换向阀控制，可以在10%--100%范围内实现制冷量的无极调节，并能保证压缩机始终处于低能级启动，以达到较小的启动扭矩，滑阀的工作位置可通过能量传感机构转换为能量百分数，并且在机组的控制盘上显示出来。
为使压缩机正常工作，需要向压缩机内喷油。
向压缩机工作腔喷油，可以起到密封和冷却的作用；轴承、轴封、平衡活塞的工作也需要提供润滑油。
气体压缩机说明书
en Installation instructions1234265626enSafe installationFollow these safety instructions when installing the appliance.¡Read this instruction manual carefully.¡The images shown in these instructions are for guidance only.¡The appliance can only be used safely if it is cor-rectly installed according to the safety instructions.The installer is responsible for ensuring that the appliance works perfectly at its installation loca-tion.WARNING ‒ Risk of explosion!Escaping gas may cause an explosion.▶All Installation, connection, regulating and conver-sion work to a different gas type must be carried out by an authorised professional while taking into account the respective applicable regulations and legal requirements as well as the regulations re-garding the local electricity and gas suppliers.Special attention must be paid to the provisions and guidelines that are applicable for the ventila-tion. For conversion work to a different gas type,we recommend that you call the after-sales ser-vice.¡Ensure that the kitchen is sufficiently ventilated, in particular when operating the gas cooking appli-ance.¡Do not connect the appliance to an exhaust gas system for combustion products.¡Never install the appliance in boats or in vehicles.¡The warranty applies only when using the appli-ance as intended.¡Before installing the appliance, check that the local conditions of the supplier are compatible with the appliance settings specified on the rating plate (type of gas and pressure, power, voltage).¡Secure the power cord to the cabinet to prevent it from touching hot parts of the oven or hob.¡Before any work is carried out on the appliance,switch off the power supply and the gas supply.¡Connect the appliance to the power supply using the earth.¡Do not make any changes to the inside of the ap-pliance. If required, contact our technical cus-tomer service.Before installing¡This appliance is a class 3 appliance in accord-ance with the EN 30-1-1 standard for gas appli-ances: Built-in appliance.¡This appliance can be combined with other hobs of the same brand by using the connection ac-cessory. See catalogue.¡The unit in which the appliance is installed must be stable and secured appropriately.¡The units in the vicinity of the appliance, the lamin-ated panels and the adhesive with which they are secured must be made of non-flammable, heat-resistant materials.¡Do not install this appliance above refrigerators,washing machines, dishwashers or similar.¡The appliance must only be installed on an oven with forced ventilation. Check the dimensions of the oven in the installation instructions for the oven.¡If you install an oven underneath the hob, the work surface thickness may differ from the dimensions given in these instructions. Take note of the in-formation in the oven installation instructions.¡If you install an exhaust air fan or an extractorhood, refer to the installation instructions for these.Always observe the minimum vertical distance to the hob.→ Fig. 1Preparing the units¡Make a cut-out in the worktop with the required di-mensions.¡In recesses of 500 mm, the appliance must be in-stalled on the front edge of the recess. → "Posi-tioning the appliance", Page 7→ Fig. 2¡Seal the cut surfaces of wooden work surfaces with a special glue seal to protect them from mois-ture.¡If there is no built-in oven underneath the hob, in-sert a non-flammable separator (e.g. metal or ply-wood) at a distance of 10 mm from the hob. This prevents access to the underside of the hob. The distance from the intermediate floor to the mains connection for the appliance must be at least 10mm.→ Fig. 3, → Fig. 47Positioning the applianceNote: Do not remove the adhesive seal fitted on the lower edge of the hob. The adhesive seal prevents the penetration of liquids.Do not use silicone to bond the appliance to the worktop.1.Position the hob with the upper side facing down on a flat, stable surface.2.Loosen the screws on the brackets so they can turn freely. You do not need to fully undo the screws on the brackets.→ Fig. 53.Turn the hob around and insert it into the recess.Insert the hob in the front of the recess.→ Fig. 64.Turn the brackets and tighten them fully.→ Fig. 7The position of the brackets depends on the work-top thickness.Removing the appliance1.Disconnect the appliance from the electricity andgas connections.2.Unscrew the brackets and proceed in reverse or-der.Connecting the gasObserve the country-specific guidelines.CAUTION ‒ Risk of explosion!A gas leakage may cause an explosion.▶If any connection is handled, check the seal.¡Arrange the gas connection so that the shut-off valve is accessible.¡Ensure that the information on the rating plate re-garding the gas type and gas pressure complies with the local connection conditions.¡Connect the appliance to a fixed gas pipe or a flexible metal pipe.¡The flexible metal pipe must not come into contact with the moving parts of the unit in which the ap-pliance is installed (e.g. a drawer) and must not be routed through any spaces which might be-come obstructed.¡Gas connection on the appliance: G 1/2.Spare parts for gas connectionYou can obtain the gas connection parts from the technical customer service.Pipe10008834Pipe for horizontal connection10003285Gas connection G 1/2▶Insert the seal between the gas connection of the appliance and the gas supply.→ Fig. 8LPG rubber hose connection1.Secure the sealing ring and the pipe that is sup-plied in the accessory bag to the appliance's gas inlet elbow.2.Insert the rubber hose into the end of the pipe and tighten the screw on the hose clamp.→ Fig. 9Electrical connection¡This appliance is type Y: The connection cable must only be replaced by technical customer ser-vice and not by the user. The cable type and the minimum cross section must be respected.¡The hobs are supplied with a power cord with or without a plug.¡Only connect appliances that are fitted with a plug to a correctly installed socket with protective earth conductor.¡If the plug is not accessible to the user, an all-pole isolating safety switch with a minimum contact opening of 3 mm must be provided.→ Fig. 10Converting the gas typeIf the country's regulations allow, this appliance can be adapted to other types of gas, if these are listed on the rating plate.You can find the right parts in the bag that is sup-plied with the appliance or you can obtain them from customer service. The table → Fig. 26 shows the right combination for the relevant burner and gas type.¡2 - Inner flameToolsContact technical customer service to purchase the relevant tools.Removal lever483196Removing the upper part of the appliance (glass plate with cut-out profiles)1.Remove the pan supports, burner caps, distribut-ors and rotary knobs.2.Undo the screws on the burners.→ Fig. 113.Move the removal lever under the metal cut-out profile into the area marked for the hob model and loosen the front clip fastener.→ Fig. 12Only use the lever under the cut-out profiles or the metal frame of the hob.4.Carefully lift the glass plate with the cut-out pro-files to release the rear clip fastener.Removing the circuit boardTip: The circuit board is secured to the holder by fastening pins at the sides and in the middle. Push the fastening pins carefully without damaging them.If one of the pins breaks, the entire holder must be replaced.ATTENTION!The circuit board can be damaged by improper handling.▶Handle the circuit board carefully.▶Use anti-static shields or hold the circuit board at the edges.▶Never touch the surfaces of the circuit board on which there are components or conducting tracks.1.Undo the fastening pins on one side.2.Release the fastening pins in the middle by press-ing on them from both sides with your fingers.3.Undo the fastening pins on the other side and re-move the circuit board.→ Fig. 13Adjusting the tapsRequirement: The upper part of the appliance and the circuit board are removed. → "Removing the up-per part of the appliance (glass plate with cut-out profiles)", Page 7 → "Removing the circuit board", Page 71.Remove the cylindrical parts and springs from thefittings spindle.2.When adjusting the bypass screws (M), refer tothe table → Fig. 26.‒A: Firmly tighten the bypass screws.‒B: The bypass screws must be flush with the fit-ting.→ Fig. 14Replacing the nozzles▶Replace the nozzles using the appropriate wrench and tighten them carefully to guarantee the seal.→ Fig. 15Ensure that the nozzle does not become detached during removal or fastening.Replacing the outer flame nozzle on the multi-crown burnerRequirement: The upper part of the appliance has been removed. → "Removing the upper part of the appliance (glass plate with cut-out profiles)", Page 7 1.To gain access to the main nozzle, loosen thefastening screw and pull the sleeve back.→ Fig. 162.Remove the nozzle by turning it anti-clockwiseand screw in the new outer flame nozzle .→ Fig. 173.Set the spacing of the adjustment sleeve for theair supply to dimension Z, as shown in the table → Fig. 26.→ Fig. 184.Tighten the fastening screw.→ Fig. 19Replacing the inner flame nozzle on the multi-crown burnerRequirement: The upper part of the appliance has been removed. → "Removing the upper part of the appliance (glass plate with cut-out profiles)", Page 7 1.Unscrew the tube by applying pressure to thesleeve in the opposite direction to hold it in placeand pulling the tube out of the sleeve .→ Fig. 202.Remove the sleeve.→ Fig. 213.Remove the inner flame nozzle from the sleeveand screw in the new nozzle.→ Fig. 224.Screw the sleeve and the tube back into their ori-ginal position.Reinstalling the appliance▶Install the appliance components in reverse order. Checking if equipment is working1.Check that turning the rotary knob between theposition for maximum power and the position for minimum power does not cause the burner to go out or result in backfire.2.If the gas flow from the burner is not correct, inthe table → Fig. 26, check whether the nozzle and the position of the bypass screw are correct.Calibrating the electronics▶→ Fig. 23, → Fig. 24, → Fig. 25Always recalibrate the electronics after reas-sembling.Documenting the gas type conversion▶Attach the sticker showing the new gas type near to the rating plate.8。
单级压缩螺杆式机压缩机说明书
螺杆空气压缩机使用说明书在安装或第一次起动压缩机前，请仔细阅读本手册，清楚了解压缩机的有关知识以及操作维修的注意事项。
请把本手册与机器一同移交使用者。
本技术手册内有重要的安全信息，应一直与压缩机一起保存。
目录1、产品说明 (2)2、工作原理 (4)3、主要技术参数 (5)4、主要结构 (8)5、管路流程图 (9)6、电气原理图 (10)7、工频控制器基本操作及参数设置 (12)8、变频控制器基本操作及参数设置 (18)9、警告及注意事项 (35)10、设备安装 (38)11、设备操作 (38)12、使用和维护 (40)13、故障和排除 (46)1 产品说明1.1 有关压缩机的说明本公司螺杆压缩机是经多年研究开发的成果。
这些先决条件与高质量标准结合，可保证制造的螺杆压缩机寿命长、可靠性高、运行效益高。
产品能够满足所有环保要求。
1.2 使用范围本系列机器和机组是根据已成熟的技术和公认的安全规则生产的。
然而若出现以下情况，则仍可能对使用者或第三方的生命和肢体造成威胁，或对机器和其他物质财产带来损害：●使用范围不正确●由不合格人员操作●不合理地修改或改变机器●不遵守安全规则因此，任何有权对机器进行操作、维护或修理的人员必须阅读并遵守安全规程。
需要时，可以要求签字对此进行确认。
此外，还必须遵守:●有关的事故防范规则●公认的安全法规●国家法规本系列机器和机组必须在完善的技术条件下使用，必须根据操作手册规定的使用范围和指南进行使用，使用人员必须有安全意识，能充分认识操作机器中存在的危险。
若发生任何功能性故障，尤其是影响安全的故障，都必须及时修理（或请别人修理）！在使用范围内操作机器的含义中，还包括应遵守操作手册中的各项指南，按规定进行检查和保养等。
1.3保养本机必须精心维护，以使螺旋压缩机或压缩机组能满足各种不同要求。
因此必须坚持按规定的保养期限对机器仔细进行维护保养，在工作环境恶劣的情况下尤其应这样做。
服务出现故障或需要备件时，请与特约本公司压缩机商家联系。
空气压缩机使用说明书1
YC90L-4空气压缩机使用说明书编号：2009056目录：1.YC90L-4型空气压缩机主要技术规范2.压缩机主要部件简述3.压缩机的安装要求4.压缩机的试运转5.压缩机的正常操作6.压缩机可能发生的故障及消除7.压缩机的检修8.压缩机的启封9.附录A：机体与电机的安装1.ZW-22.5/8型空气压缩机主要技术规范（1）型式：立式、两列、二级、双作用、水冷、气缸无润滑（2）输气量1350m3/h±5%（吸入状态）（3）吸入介质状态：大气吸入进气压力：当地大气压进气温度：≤35℃（4）最终压力：0.8MPa（G）（5）末级冷却器后出气温度：≤40℃（6）气缸直径：一级缸φ430mm，二级缸φ250mm（7）活塞行程：180mm（8）转速：590r/min（9）曲轴旋转方向：从油泵端看为逆时针方向（10）传动方式：皮带轮传动（11）轴功率：132kW（12）压缩机总重量：~6000kg（包括电动机、辅机、管道）（13）电动机：型号Y315M-4电压380V转速1485r/min功率132kW（14）冷却水压：进水压力0.3Mpa（G）；回水压力0.25Mpa（G）（15）冷却水进水温度：〈30℃（16）却水耗量：~15T/h（17）一级进气管径：φ219×6（18）末级出气管径：φ133×42.压缩机主要部件简述本机主要由机身、曲轴、连杆、十字头、刮油器、油过滤器、油冷却器、机带油泵、动力装置、气缸、活塞、气阀、密封器、高效气体冷却器、管路系统以及压缩机控制柜等部件组成。
气体的压缩过程见随机图纸Y201.LC流程图。
2.1 机身压缩机的机身是包括曲轴箱、中间体铸成的整体，其材质为高强度铸铁铸成。
2.2 曲轴曲轴用稀土球墨铸铁铸成，支承在曲轴箱中的两个轴承上，两列曲拐相差180度。
曲轴一端的飞轮通过皮带与电动机联接，另一端通过超越离合器带动齿轮油泵。
曲轴内钻有输油孔，是连杆大头轴承和小轴瓦头润滑油必经通路。
无油螺杆空气压缩机说明书_200610
按照压缩机冷却水进出管尺寸及流量要求，将符合条件耐压合适的冷却水用的水管联接到压缩 机上。
进水总管上用户要安装水过滤器，以过滤水中的主要杂质，保证压缩机的正常运行。此外进出 水总管路上要安装放水阀，进水总管路上要安装截止阀。进出水总管安装见图 7。
出水总管 进水总管
截止阀 2.6 电源供应
过滤器 图 7 进出水总管安装示意图
缩机经过预检、处于正常状态时方可进行。
注意！
尽管压缩机在出厂前已进行了全面的出厂试验，运输前也作了充分的检查，但不
能排除运输过程中的损坏。因此，在压缩机初次使用之前必须重新认真检查压缩机。
此外，在初次使用的前几个小时运行过程中，必须仔细观察压缩机运行情况。
4.1 拆除掉运输过程中用来定位、固定的紧固件。 4.2 再次紧固电控中所有接线端。 4.3 检查电控、仪表等是否松动或损坏。 4.4 检查管件、管接头是否开裂或松动。 4.5 检查外接电缆是否正确，是否符合安全规程的要求。 4.6 检查电机过载继电器整定值是否正确。LGWD-42/8 型螺杆压缩机主电机过载继电器整定值为 4.7A，风扇电机过载继电器整定值为 3.2A。 4.7 检查齿轮箱中的润滑油高度，正常情况下油位应在上视镜可见，并在其 1/2 以下(参看图 11)。
最小维修尺寸 H
最小维修尺寸 A
符号
A
尺寸
1
最小维修尺寸 D
最小维修尺寸 B
最小维修尺寸 C
图 3 压缩机最小维修尺寸示意图
B
C
D
1.2
1
1.2
单位：m H 1.5
压缩机应安装在低温、干燥的室内场所，避免室外安装。 工作环境要求通风良好，环境温度必须保证在 0～40℃之间。 要避免热的排风被循环吸入压缩机内，可采取将热的排风引至室外，或通过引管直接从室外吸 风的措施。
富达压缩机说明书
目录目录 (1)前言 (3)产品责任 (4)安全须知 (5)第一章空压机的安装 (8)1.1压缩机的搬运 (8)1.2压缩机房的选址 (8)1.3压缩机房的布局和压缩机的安装 (8)1.4压缩机供电系统安装 (9)1.5压缩机的管道安装 (21)1.6空压机的通风 (21)1.7压缩机技术参数 (22)压缩机系统流程及零部件功能简介介 (24)第二章压缩机系统流程及零部件功能简2.1风冷型空压机的系统流程图 (24)2.2 空压机的各零部件的主要功能 (24)第三章操作指南 (26)3.1 空压机开机前的准备工作 (26)3.2 空压机的启动 (26)3.3 空压机的运行 (26)3.4 空压机的停机 (27)第四章电脑控制器 (28)4.1标准型电脑控制器 (28)4.2 变频电脑控制器 (30)4.3保养计划 (37)第六章预防性保养 (39)6.1 预防性保养计划 (39)6.2 预防性保养包简介 (41)6.3保养合同 (41)6.4转子润滑液的规格 (41)6.5 处理过的材料 (42)第七章 压缩机的使用 (43)7.1 概述 (43)7.2 日常保养 (43)7.3储气罐排放冷凝水 (43)7.4 转子润滑液的添加 (44)7.5 更换转子润滑液 (44)7.6电机加润滑脂 (44)7.7 安全阀维护 (44)7.8 冷却器的维护 (44)第八章 机器故障分析与排除 (45)8.1 概述 (45)8.2 常规机器常见故障排除表 (45)第九章 压缩机的储存 ............................................................................................ 47 附页附页：：压缩机维护保养登记表 (47)前言非常感谢您购买和使用本公司生产的螺杆空气压缩机（以下简称压缩机或空压机）。
为了确保机组安全、可靠地投入运行，请用户务必在使用压缩机之前详细阅读使用说明书，并严格按照使用说明书中的要求，安装、使用、保养、维修和贮存机组。
DA AT 系列医用无油空气压缩机 技术说明书 使用说明书
DA/AT系列医用无油空气压缩机技术说明书使用说明书产品标准号：产品注册号：生产许可证号：苏食药监械生产许2012-0047号。
(在使用、保养或维修设备前请仔细阅读说明书，说明书只作指导用，公司有权对设备进行改进设计)目录第一章概述 (3)1.1 使用说明书所包含的内容 (3)1.2 产品结构及组成 (3)1.3 产品适用范围 (3)1.4 安全信息 (3)1.5 产品信息 (4)1.6 版本信息 (4)第二章技术参数 (5)2.1 技术参数 (5)2.2 产品分类 (6)2.3 运输储存和使用环境 (6)2.4 产品铭牌 (6)2.5 图例说明 (6)第三章医用无油空气压缩机整体结构 (7)第四章产品性能……………………………………………………………………………… .17 第五章产品安装……………………………………………………………………………… .18 第六章调试使用……………………………………………………………………………… .19 第七章保养及维护…………………………………………………………………………… .20 第八章注意事项……………………………………………………………………………… .22 第九章装箱清单……………………………………………………………………………… .23 第十章电路及气路原理图…………………………………………………………………… .24 第十一章外包装标签及内容………………………………………………………………… .29非常感谢您选择使用本公司生产的医用无油空气压缩机！在第一次安装和使用医用无油空气压缩机之前，请您务必先仔细阅读随机附送的所有资料，特别是本使用说明书中安装信息及其它条款所提及的注意事项。
这会有助于您更好地使用岱洛产品。
免责声明本使用说明书的描述不代表对岱洛产品的规格和配置的任何说明，有关产品规格及配置情况，请查阅与岱洛产品的相关协议、装箱单或向产品的直接经销商咨询。
富威压缩机说明书
富威压缩机说明书摘要：一、引言二、产品简介三、性能参数四、安装与调试五、操作与维护六、故障排除七、售后服务正文：【引言】富威压缩机是一款高效、节能、环保的新型压缩机产品，广泛应用于各种工业领域。
本说明书旨在为用户提供详细的产品信息，帮助用户正确安装、使用和维护富威压缩机。
【产品简介】富威压缩机采用先进的螺杆式压缩技术，具有体积小、噪音低、振动小、效率高等优点。
产品系列丰富，可根据用户需求选择合适的型号。
本说明书以富威压缩机FV-50 为例，介绍产品的基本参数和性能。
【性能参数】1.型号：FV-502.排气量：50m/min3.额定功率：11kW4.电源：380V/50Hz5.工作压力：0.5-1.0MPa6.制冷剂：R134a【安装与调试】1.安装环境：富威压缩机应安装在通风良好、无腐蚀性气体、无尘埃、无易燃易爆物品的室内。
2.安装基础：根据安装图纸，确保基础平整、牢固，并预留足够的维修空间。
3.管路连接：按照安装图纸连接进出口管路，注意管道的弯头、阀门等应符合设计要求。
4.电气连接：按照安装图纸接线，确保接线正确、牢固。
5.调试：启动压缩机，检查运行声音、振动、温度等参数是否正常，如有异常应立即停机检查。
【操作与维护】1.操作：启动压缩机前，检查油位、冷却水、电源等是否正常，启动后观察运行参数，如有异常应立即停机。
2.维护：定期检查油位、油质、冷却水等，保持设备清洁，及时更换损坏的零部件。
3.保养：每运行500 小时，更换润滑油；每运行1000 小时，进行一次全面检查和保养。
【故障排除】1.故障现象：压缩机无法启动可能原因：电源故障、保险丝熔断、接线不良等解决方法：检查电源、接线，修复或更换损坏部件2.故障现象：压缩机运行中突然停止可能原因：压力过高、过载、缺油等解决方法：检查压力、油位等参数，及时添加或更换润滑油【售后服务】富威公司承诺为用户提供优质的售后服务，包括产品安装、调试、培训、维修等。
NorthStar 压缩机泵说明书
Any Questions, Comments, Problems, or Parts Orders Call NorthStar Product Support 1-800-270-0810Thank you for purchasing a NorthStar compressor pump. Your pump is designed for long life, dependability, and the top performance you demand. Please take time now to read through this manual so y ou can better understand the pump’s safety precautions. Everyone who uses the pump must read and understand this manual. Enjoy the exceptional performance of your NorthStar pump.Make certain the operator:- Reads and understands the manuals pertaining to this tank.- Is instructed in safe and proper operation of this air compressor tank.K-BAR Industries Incorporated reserves the right to make improvements in design and/or changes in specifications at any time without incurring any obligation to install them on units previously sold.ALWAYS bleed pressure from tank before servicing.ALWAYS use air handling parts that are rated above the maximum allowable working pressure of the tank.ALWAYS drain tank daily or after each use. Rusted tanks can cause explosion and cause severe injury or death.ALWAYS read your owners manual before operating.ALWAYS use at least one safety relief valve rated at 200 psi or below.ALWAYS use an ASME certified air receiver tank.ALWAYS use Teflon tape on all treads to reduce leaks.NEVER exceed the nameplate rating of the tank(200 psi working pressure). Exceeding this rating can cause explosion and cause severe injury or death.NEVER operate machine without a belt guard in place.NEVER bypass, modify, or remove safety/relief valves.NEVER direct air stream at people or animalsNEVER modify or repair tank, obtain replacement from a service center or customer service at 1-800-270-0810.NEVER breathe receiver air. Can contain Carbon Monoxide or other contaminants.Will cause serious injury or death.NorthStar air compressor tanks are not designed for breathing air.CAUTION! Do not operate without lubricant or with inadequate lubricant.Use of compressor without lubricant or inadequate lubricant voids all warranties.Synthetic LubricantsSynthetic lubricants are recommended after 50 hour break-in. Compressor life is greatly increased with the use of synthetic lubricants. CAUTION! If you will be using synthetic lubricant, all downstream piping material and system components must be compatible.Suitable Viton®, Teflon®, Epoxy (Glass Filled), Oil Resistant Alkyd, Fluorosilicone, Flourocarbon, Polysulfide, 2-Component Urethane, Nylon, Delrin®, Celcon®, High Nitrile Rubber (Buna N. NBR more than 36Acrylonite), Polyurethane, Polyethylene, Epichlorohydrin, Polyacrylate, Melamine, Polypropylene, Baked Phenolics, Epoxy, Modified Alkyds( ® indicates trademark of DuPont Corporation)Not RecommendedNeoprene, Natural Rubber, SBR Rubber, Acrylic Paint, Lacquer, Varnish, Polystyrene, PVC, ABS,Polycarbonite, Cellulose Acetate, Latex, EPR, Acrylics, Phenoxy, Polysulfones, Styrene Acrylonitile(San), ButylAlternate Lubricants.You may use petroleum-based lubricant that is premium quality, does not contain detergents, contains only anti-rust, anti-oxidation, and anti-foam agents as additives, has a flashpoint of 440︒F (227︒C) or higher, and has a auto-ignition point of 650︒F (343︒C) or higher.See the petroleum lubricant viscosity table below. The table is intended as a general guide only. Heavy duty operating conditions require heavier viscosities. Refer specific operating conditions to NorthStar Customer Service at 1-800-270-0810 Monday - Friday 7:00 AM-5:30 PM, Saturday 7:30 AM-11:30 AM Central Standard Time.Pump Capacities.Refer to the following table for crankcase capacityDear Valued Customer:The NorthStar Product you just purchased is built with the finest material and craftsmanship. Use this product properly and enjoy the benefits from its high performance. By purchasing a NorthStar product, you show a desire for quality and durability.Like all mechanical equipment this unit requires a due amount of care. Treat this unit like the high quality piece of machinery it is. Neglect and improper handling may impair its performance. Please thoroughly read the instructions and understand the operation before using your product.Limited WarrantyNorthStar shall warranty any piece of equipment manufactured, or parts of equipment manufactured, to be free from defects in material or workmanship for a period of 1 year from the date of purchase by user. This warranty applies to the original purchaser of the equipment and is non transferable. Verification of purchase is the responsibility of the buyer. Parts will be replaced or repaired at no charge, except when the equipment has failed due to lack of proper maintenance. Any misuse, abuse, alteration or improper installation or operations will void warranty. Determining whether a part is to be replaced or repaired is the sole decision of NorthStar.NOTE: Some services performed by parties other than NorthStar may void warranty.This warranty covers parts only. It will not provide for replacement of complete products due to defective parts. Components not manufactured by NorthStar such as engines are guaranteed by their manufacturer and can be serviced at factory-authorized locations near you. Any costs incurred due to replacement or repair of items outside of a NorthStar approved facility is the responsibility of the buyer and not covered under warranty. NorthStar can supply you with the service center location in your area. This warranty specifically excludes the following; failure of parts due to damage caused by accident, fire, flood, windstorm, acts of God, applications not approved by NorthStar in writing, corrosion caused by chemicals, use of replacement parts which do not conform to manufacturer’s specifications, and damage caused by vandalism. Additional exc lusions: loss of running time, inconvenience, loss of income, or loss of use, including any implied warranty of merchantability of fitness for a specific use.Warranty does not cover items subject to normal wear such as tires, receptacles or any part subject to direct physical contact by the public. This warranty does not cover any personal injury or damage to surrounding property caused by failure of any part.This warranty is in lieu of any other warranty expressed or implied and NorthStar assumes no other responsibility or liability outside that expressed within this warranty.Please fill in the following information and have it on hand when you call in a warranty claim.Customer Number: ______________________________________________________________Date of Purchase: _______________________________________________________________NorthStar Serial Number: ________________________________________________________Item Number: __________________________________________________________________。
空压机使用说明书
空压机使用说明书空压机使用说明书一、产品介绍空压机是一种将大气中的气体压缩成高压气体的设备。
本文档将详细介绍空压机的使用方法和注意事项。
二、安全须知1、操作前，请务必仔细阅读本说明书，了解各个部件的功能和操作方法。
2、在操作过程中，严禁将手指、头部或其他物体放入机器内部。
3、使用前应检查电源线插头是否完好，并确保插座接地良好。
4、在操作过程中，严禁将待压缩气体喷射到人体上，以免引起伤害。
三、机器操作1、启动和关闭a：将开关拨至“ON”位置，待机器启动后即可正常工作。
b：在使用完毕后，将开关拨至“OFF”位置，停止机器运行。
2、压力调节a：使用压力表来调节空压机的输出压力，确保符合所需工作压力。
b：注意不要超过空压机的额定工作压力，否则可能会导致设备损坏或危险事故。
3、润滑油更换a：根据使用频率和工作环境，定期更换润滑油。
b：在更换润滑油时，务必按照说明书的要求进行操作。
4、清洁和维护a：定期清洁空压机的滤网和冷却器，以确保机器正常运行。
b：注意不要用水直接清洗机器，以免损坏机器部件。
四、故障排除1、机器无法启动a：检查电源是否正常连接。
b：确认开关是否处于正确位置。
2、压力过高或过低a：检查压力表是否正常工作。
b：检查机器是否存在漏气的情况。
3、异常噪音或振动a：检查机器是否处于稳定的工作状态。
b：确认机器各个部件是否牢固固定。
五、附件本文档涉及的附件包括：1、产品说明书2、电源线3、压力表六、法律名词及注释1、法律名词：压力调节器，指调节空压机输出气体压力的装置。
2、注释：压力调节器通常由压力表和调节装置组成，用于确保空压机输出的气体压力处于正常范围内。
- 1、下载文档前请自行甄别文档内容的完整性，平台不提供额外的编辑、内容补充、找答案等附加服务。
- 2、"仅部分预览"的文档,不可在线预览部分如存在完整性等问题,可反馈申请退款(可完整预览的文档不适用该条件!)。
- 3、如文档侵犯您的权益，请联系客服反馈,我们会尽快为您处理(人工客服工作时间：9:00-18:30)。
矿产资源开发利用方案编写内容要求及审查大纲
矿产资源开发利用方案编写内容要求及《矿产资源开发利用方案》审查大纲一、概述
㈠矿区位置、隶属关系和企业性质。
如为改扩建矿山, 应说明矿山现状、
特点及存在的主要问题。
㈡编制依据
(1简述项目前期工作进展情况及与有关方面对项目的意向性协议情况。
(2 列出开发利用方案编制所依据的主要基础性资料的名称。
如经储量管理部门认定的矿区地质勘探报告、选矿试验报告、加工利用试验报告、工程地质初评资料、矿区水文资料和供水资料等。
对改、扩建矿山应有生产实际资料, 如矿山总平面现状图、矿床开拓系统图、采场现状图和主要采选设备清单等。
二、矿产品需求现状和预测
㈠该矿产在国内需求情况和市场供应情况
1、矿产品现状及加工利用趋向。
2、国内近、远期的需求量及主要销向预测。
㈡产品价格分析
1、国内矿产品价格现状。
2、矿产品价格稳定性及变化趋势。
三、矿产资源概况
㈠矿区总体概况
1、矿区总体规划情况。
2、矿区矿产资源概况。
3、该设计与矿区总体开发的关系。
㈡该设计项目的资源概况
1、矿床地质及构造特征。
2、矿床开采技术条件及水文地质条件。