juniper WLC无线控制器快速配置向导

一、清空MX配置
MXR-2# quickstart
This will erase any existing config. Continue? [n]: yes
Answer the following questions. Enter ‘?’ for help. ^C to break out
System Name [MXR-2]: ^C //ctrl+c
MXR-2-560CB8# //配置已清空

二、配置系统信息
Set timezone CNT 8 //设置时区
Set timedata date october 14 2008 time 14:16:00 //设置时间
Set system countrycode CN
This will cause all APs to reboot. Are you sure? (y/n) [n]yes //设置国家代码，
Set system ip-address 172.16.2.2
This will cause all APs to reboot. Are you sure? (y/n) [n]yes //配置系统管理IP
Set ip route default 172.16.2.1 1 //配置MX的默认路由和metric
Set enablepass +回车
Enter old password:
Enter new password:
Retype new password: //配置enable密码

三、配置无线交换机接口vlan信息
set vlan 10 name user //创建vlan10为用户vlan，取名“user”
set vlan 10 port 1 tag 10 //配置端口1为trunk模式，tag为10
set vlan 2 name mgmt //创建vlan2为管理vlan，取名“mgmt”
set vlan 2 port 1 tag 2 //端口1打上tag 2的标记
set interface 10 ip 10.10.10.100 255.255.255.0 //配置用户vlan的接口地址
set interface 2 ip 172.16.2.2 255.255.255.0 //配置MX的接口地址，即MX的系统IP

四、配置wep加密的service-profile
set service-profile XXX ssid-name ruijie //创建名为XXX的SP，SSID名为“ruijie”
set service-profile XXX ssid-type crypto //加密类型为crypto，即加密
set service-profile XXX wep key-index 1 key 1234567890 //配置wep的密钥为1234567890
set service-profile XXX auth-fallthru last-resort //认证类型为last-resort，即开放式认证
set service-profile XXX attr vlan-name user //该 SP关联的用户vlan为“user”

五、配置AP
set ap 1 serial-id xxxxxxxxx model MP-71 //注册AP的型号和序列号
set ap auto mode enable //开启自动发现模式
set ap 1 radio 1 radio-profile YYY mode enable //将R-P应用到AP的radio 1上
set ap 1 boot-configuration ip 10.1.1.3 netmask 255.255.255.0 gateway 10.1.1.1 mode enable
//配置AP的静态IP地址
set ap 1 boot-configuration switch switch-ip 172.16.2.2 mode enable //在AP内添加MX的IP地址

save config file:config1
dir
loal config config1
coa rf3576

set ip route default 192.168.1.254
set system name MXR-2
set system ip-address 192.168.1.220
set system countrycode CN
set service-profile juniper-wlan ssid-name juniper-wlan
set service-profile juniper-wlan ssid-type clear
set service-profile juniper-wlan auth-fallthru last-resort
set service-profile juniper-wlan 11n mode-ng disable
set service-profile juniper-wlan wpa-ie auth-dot1x disable
set service-profile juniper-wlan rsn-ie auth-dot1x disable
set service-profile juniper-wlan attr vlan-name default
set enablepass password c79101664a2b85fcb9982d93e6e9dcb5ecc7
set user admin password encrypted 070e25414707
set radio-profile default service-profile juniper-wlan
set ap auto mode enable
set ip telnet server enable

set port poe 2 enable
set vlan 1 port 1
set vlan 1 port 2
set interface 1 ip 192.168.1.220 255.255.255.0
set interface 1 ip dhcp-server enable start 192.168.1.220 stop 192.168.1.223