机械外文翻译
Lathes
Lathes are machine tools designed primarily to do turning, facing and boring, Very little turning is done on other types of machine tools, and none can do it with equal facility. Because lathes also can do drilling and reaming, their versatility permits several operations to be done with a single setup of the work piece. Consequently, more lathes of various types are used in manufacturing than any other machine tool.
The essential components of a lathe are the bed, headstock assembly, tailstock assembly, and the leads crew and feed rod.
The bed is the backbone of a lathe. It usually is made of well normalized or aged gray or nodular cast iron and provides s heavy, rigid frame on which all the other basic components are mounted.Two sets of parallel,longitudinal ways, inner and outer, are contained on the bed, usually on the upper side. Some makers use an inverted V-shape for all four ways, whereas others utilize one inverted V and one flat way in one or both sets, They are precision-machined to assure accuracy of alignment.On most modern lathes the way are surface-hardened to resist wear and abrasion, but precaution should be taken in operating a lathe to assure that the ways are not damaged.Any inaccuracy in them usually means that the accuracy of the entire lathe is destroyed.
The headstock is mounted in a foxed position on the inner ways, usually at the left end of the bed. It provides a powered means of rotating the word at various speeds . Essentially, it consists of a hollow spindle, mounted in accurate bearings, and a set of transmission gears-similar to a truck transmission—through which the spindle can be rotated at a number of speeds. Most lathes provide from 8 to 18 speeds, usually in a geometric ratio, and on modern lathes all the speeds can be obtained merely by moving from two to four levers. An increasing trend is to provide a continuously variable speed range through electrical or mechanical drives.
Because the accuracy of a lathe is greatly dependent on the spindle, it is of heavy construction and mounted in heavy bearings, usually preloaded tapered roller or ball types. The spindle has a hole extending through its length, through which long bar stock can be fed.
The size of maximum size of bar stock that can be machined when the material must be fed through spindle.
The tailsticd assembly consists, essentially, of three parts. A lower casting fits on the inner ways of the bed and can slide longitudinally thereon, with a means for clamping the entire assembly in any desired location, An upper casting fits on the lower one and can be moved transversely upon it, on some type of keyed ways, to permit aligning the assembly is the tailstock quill. This is a hollow steel cylinder, usually about 51 to 76mm(2to 3 inches) in diameter, that can be moved several inches longitudinally in and out of the upper casting by means of a hand wheel and screw.
The size of a lathe is designated by two dimensions.The first is known as the swing. This is the maximum diameter of work that can be rotated on a lathe.It is approximately twice the distance between the line connecting the lathe centers and the nearest point on the ways, The second size dimension is the maximum distance between centers. The swing thus indicates the maximum work piece diameter that can be turned in the lathe, while the distance between centers indicates the maximum length of work piece that can be mounted between centers.
Engine lathes are the type most frequently used in manufacturing. They are heavy-duty machine tools with all the components described previously and have power drive for all tool movements except on the compound rest. They commonly range in size from 305 to 610 mm(12 to 24 inches)swing and from 610 to 1219 mm(24 to 48 inches) center distances, but swings up to 1270 mm(50 inches) and center distances up to 3658mm(12 feet) are not uncommon.Most have chip pans and a built-in coolant circulating system. Smaller engine lathes-with swings usually not over 330 mm (13 inches ) –also are available in bench type, designed for the bed to be mounted on a bench on a bench or cabinet.
Although engine lathes are versatile and very useful, because of the time required for changing and setting tools and for making measurements on the work piece, thy are not suitable for quantity production. Often the actual chip-production tine is less than 30% of the total cycle time. In addition, a skilled machinist is required for all the operations, and such persons are costly and often in short supply. However,much of the operator’s time is consumed by simple,repetitious adjustments and in watching chips being made.
Consequently, to reduce or eliminate the amount of skilled labor that is required, turret lathes, screw machines,and other types of semiautomatic and automatic lathes have been highly developed and are widely used in manufacturing.
2 Numerical Control
One of the most fundamental concepts in the area of advanced manufacturing technologies is numerical control (NC). Prior to the advent of NC, all machine tools ere manually operated and controlled. Among the many limitations associated with manual control machine tools, perhaps none is more prominent than the limitation of operator skills. With manual control, the quality of the product is directly related to and limited to the skills of the operator. Numerical control represents the first major step away from human control of machine tools.
Numerical control means the control of machine tools and other manufacturing systems through the use of prerecorded,written symbolic instructions. Rather than operating a machine tool, an NC technician writes a program that issues operational instructions to the machine tool. For a machine tool to be numerically controlled, it must be interfaced with a device for accepting and decoding the programmed instructions,known as a reader.
Numerical control was developed to overcome the limitation of human operators, and it has done so. Numerical control machines are more accurate than manually operated machines, they can produce parts more uniformly,they are faster, and the long-run tooling costs are lower. The development of NC led to the development of several other innovations in manufacturing technology:
Electrical discharge machining,Laser cutting,Electron beam welding.
Numerical control has also made machine tools more versatile than their manually operated predecessors. An NC machine tool can automatically produce a wide of parts, each involving an assortment of widely varied and complex machining processes. Numerical control has allowed manufacturers to undertake the production of products that would not have been feasible from an economic perspective using manually controlled machine tolls and processes.
Like so many advanced technologies, NC was born in the laboratories of the Massachusetts Institute of Technology. The concept of NC was developed in the early 1950s
with funding provided by the U.S. Air Force. In its earliest stages, NC machines were able to made straight cuts efficiently and effectively.
However, curved paths were a problem because the machine tool had to be programmed to undertake a series of horizontal and vertical steps to produce a curve. The shorter the straight lines making up the steps, the smoother is the curve, Each line segment in the steps had to be calculated.
This problem led to the development in 1959 of the Automatically Programmed Tools (APT) language. This is a special programming language for NC that uses statements similar to English language to define the part geometry, describe the cutting tool configuration, and specify the necessary motions. The development of the APT language was a major step forward in the fur ther development from those used today. The machines had hardwired logic circuits. The instructional programs were written on punched paper, which was later to be replaced by magnetic plastic tape. A tape reader was used to interpret the instructions written on the tape for the machine.Together,all of this represented a giant step forward in the control of machine tools. However, there were a number of problems with NC at this point in its development.
A major problem was the fragility of the punched paper tape medium.It was common for the paper tape containing the programmed instructions to break or tear during a machining process. This problem was exacerbated by the fact that each successive time a part was produced on a machine tool, the paper tape carrying the programmed instructions had to be rerun through the reader. If it was necessary to produce 100 copies of a given part, it was also necessary to run the paper tape through the reader 100 separate tines. Fragile paper tapes simply could not withstand the rigors of a shop floor environment and this kind of repeated use.
This led to the development of a special magnetic plastic tape. Whereas the paper carried the programmed instructions as a series of holes punched in the tape, the plastic tape carried the instructions as a series of magnetic dots. The plastic tape was much stronger than the paper tape, which solved the problem of frequent tearing and breakage. However, it still left two other problems.
The most important of these was that it was difficult or impossible to change the instructions entered on the tape. To made even the most minor adjustments in a program of instructions, it was necessary to interrupt machining operations and make a new tape. It was also still necessary to run the tape through the reader as many times as there were parts to be produced. Fortunately, computer technology became a reality and soon solved the problems of NC associated with punched paper and plastic tape.
The development of a concept known as direct numerical control (DNC) solved the paper and plastic tape problems associated with numerical control by simply eliminating tape as the medium for carrying the programmed instructions. In direct numerical control, machine tools are tied, via a data transmission link, to a host computer.Programs for operating the machine tools are stored in the host computer and fed to the machine tool an needed via the data transmission linkage. Direct numerical control represented a major step forward over punched tape and plastic tape. However,it is subject to the same limitations as all technologies that depend on a host computer.When the host computer goes down, the machine tools also experience downtime.This problem led to the development of computer numerical control.
3 Turning
The engine lathe, one of the oldest metal removal machines, has a number of useful and highly desirable attributes. Today these lathes are used primarily in small shops where smaller quantities rather than large production runs are encountered.
The engine lathe has been replaced in today’s production shops by a wide variety of automatic lathes such as automatic of single-point tooling for maximum metal removal, and the use of form tools for finish on a par with the fastest processing equipment on the scene today.
Tolerances for the engine lathe depend primarily on the skill of the operator. The design engineer must be careful in using tolerances of an experimental part that has been produced on the engine lathe by a skilled operator. In redesigning an experimental part for production, economical tolerances should be used.
机械专业外文翻译(中英文翻译)
外文翻译 英文原文 Belt Conveying Systems Development of driving system Among the methods of material conveying employed，belt conveyors play a very important part in the reliable carrying of material over long distances at competitive cost．Conveyor systems have become larger and more complex and drive systems have also been going through a process of evolution and will continue to do so．Nowadays，bigger belts require more power and have brought the need for larger individual drives as well as multiple drives such as 3 drives of 750 kW for one belt(this is the case for the conveyor drives in Chengzhuang Mine)．The ability to control drive acceleration torque is critical to belt conveyors’performance．An efficient drive system should be able to provide smooth，soft starts while maintaining belt tensions within the specified safe limits．For load sharing on multiple drives．torque and speed control are also important considerations in the drive system’s design. Due to the advances in conveyor drive control technology，at present many more reliable．Cost-effective and performance-driven conveyor drive systems covering a wide range of power are available for customers’ choices[1]. 1 Analysis on conveyor drive technologies 1．1 Direct drives Full-voltage starters．With a full-voltage starter design，the conveyor head shaft is direct-coupled to the motor through the gear drive．Direct full-voltage starters are adequate for relatively low-power, simple-profile conveyors．With direct fu11-voltage starters．no control is provided for various conveyor loads and．depending on the ratio between fu11-and no-1oad power requirements，empty starting times can be three or four times faster than full load．The maintenance-free starting system is simple，low-cost and very reliable．However, they cannot control starting torque and maximum stall torque；therefore．they are
人形机器人论文中英文资料对照外文翻译
中英文资料对照外文翻译 最小化传感级别不确定性联合策略的机械手控制 摘要：人形机器人的应用应该要求机器人的行为和举止表现得象人。下面的决定和控制自己在很大程度上的不确定性并存在于获取信息感觉器官的非结构化动态环境中的软件计算方法人一样能想得到。在机器人领域，关键问题之一是在感官数据中提取有用的知识，然后对信息以及感觉的不确定性划分为各个层次。本文提出了一种基于广义融合杂交分类（人工神经网络的力量，论坛渔业局）已制定和申请验证的生成合成数据观测模型，以及从实际硬件机器人。选择这个融合，主要的目标是根据内部（联合传感器）和外部（ Vision 摄像头）感觉信息最大限度地减少不确定性机器人操纵的任务。目前已被广泛有效的一种方法论就是研究专门配置5个自由度的实验室机器人和模型模拟视觉控制的机械手。在最近调查的主要不确定性的处理方法包括加权参数选择（几何融合），并指出经过训练在标准操纵机器人控制器的设计的神经网络是无法使用的。这些方法在混合配置，大大减少了更快和更精确不同级别的机械手控制的不确定性，这中方法已经通过了严格的模拟仿真和试验。 关键词：传感器融合，频分双工，游离脂肪酸，人工神经网络，软计算，机械手，可重复性，准确性，协方差矩阵，不确定性，不确定性椭球。 1 引言 各种各样的机器人的应用（工业，军事，科学，医药，社会福利，家庭和娱乐）已涌现了越来越多产品，它们操作范围大并呢那个在非结构化环境中运行 [ 3,12,15]。在大多数情况下，如何认识环境正在发生变化且每个瞬间最优控制机器人的动作是至关重要的。移动机器人也基本上都有定位和操作非常大的非结构化的动态环境和处理重大的不确定性的能力[ 1,9,19 ]。每当机器人操作在随意性自然环境时，在给定的工作将做完的条件下总是存在着某种程
ZigBee技术外文翻译
ZigBee：无线技术，低功耗传感器网络 加里莱格 美国东部时间2004年5月6日上午12:00 技师（工程师）们在发掘无线传感器的潜在应用方面从未感到任何困难。例如，在家庭安全系统方面，无线传感器相对于有线传感器更易安装。而在有线传感器的装置通常占无线传感器安装的费用80%的工业环境方面同样正确（适用）。而且相比于有线传感器的不切实际甚至是不肯能而言，无线传感器更具应用性。虽然，无线传感器需要消耗更多能量，也就是说所需电池的数量会随之增加或改变过于频繁。再加上对无线传感器由空气传送的数据可靠性的怀疑论，所以无线传感器看起来并不是那么吸引人。 一个低功率无线技术被称为ZigBee，它是无线传感器方程重写，但是。一个安全的网络技术，对最近通过的IEEE 802.15.4无线标准（图1）的顶部游戏机，ZigBee的承诺，把无线传感器的一切从工厂自动化系统到家庭安全系统，消费电子产品。与802.15.4的合作下，ZigBee提供具有电池寿命可比普通小型电池的长几年。ZigBee设备预计也便宜，有人估计销售价格最终不到3美元每节点，。由于价格低，他们应该是一个自然适应于在光线如无线交换机，无线自动调温器，烟雾探测器和家用产品。 （图1）
虽然还没有正式的规范的ZigBee存在（由ZigBee联盟是一个贸易集团，批准应该在今年年底），但ZigBee的前景似乎一片光明。技术研究公司 In-Stat/MDR在它所谓的“谨慎进取”的预测中预测，802.15.4节点和芯片销售将从今天基本上为零，增加到2010年的165万台。不是所有这些单位都将与ZigBee结合，但大多数可能会。世界研究公司预测的到2010年射频模块无线传感器出货量4.65亿美量，其中77％是ZigBee的相关。 从某种意义上说，ZigBee的光明前途在很大程度上是由于其较低的数据速率20 kbps到250 kbps的，用于取决于频段频率（图2），比标称1 Mbps的蓝牙和54的802.11g Mbps的Wi - Fi的技术。但ZigBee的不能发送电子邮件和大型文件，如Wi - Fi功能，或文件和音频，蓝牙一样。对于发送传感器的读数，这是典型的数万字节数，高带宽是没有必要，ZigBee的低带宽有助于它实现其目标和鲁棒性的低功耗，低成本。 由于ZigBee应用的是低带宽要求，ZigBee节点大部分时间可以睡眠模式，从而节省电池电源，然后醒来，快速发送数据，回去睡眠模式。而且，由于ZigBee 可以从睡眠模式过渡到15毫秒或更少主动模式下，即使是睡眠节点也可以达到适当的低延迟。有人扳动支持ZigBee的无线光开关，例如，将不会是一个唤醒延迟知道前灯亮起。与此相反，支持蓝牙唤醒延迟通常大约三秒钟。 一个ZigBee的功耗节省很大一部分来自802.15.4无线电技术，它本身是为低功耗设计的。 802.15.4采用DSSS（直接序列扩频）技术，例如，因为（跳频扩频）另类医疗及社会科学院将在保持一样使用它的频率过大的权力同步。 ZigBee节点，使用802.15.4，是几个不同的沟通方式之一，然而，某些方面比别人拥有更多的使用权力。因此，ZigBee的用户不一定能够实现传感器网络上的任何方式选择和他们仍然期望多年的电池寿命是ZigBee的标志。事实
电子技术专业英语翻译
基本电路 包括电路模型的元素被称为理想的电路元件。一个理想的电路元件是一个实际的电气元件的数学模型，就像一个电池或一个灯泡。重要的是为理想电路元件在电路模型用来表示实际的电气元件的行为可接受程度的准确性。电路分析，本单位的重点，这些工具，然后应用电路。电路分析基础上的数学方法，是用来预测行为的电路模型和其理想的电路元件。一个所期望的行为之间的比较，从设计规范，和预测的行为，形成电路分析，可能会导致电路模型的改进和理想的电路元件。一旦期望和预测的行为是一致的，可以构建物理原型。 物理原型是一个实际的电气系统，修建从实际电器元件。测量技术是用来确定实际的物理系统，定量的行为。实际的行为相比，从设计规范的行为，从电路分析预测的行为。比较可能会导致在物理样机，电路模型，或两者的改进。最终，这个反复的过程，模型，组件和系统的不断完善，可能会产生较准确地符合设计规范的设计，从而满足需要。 从这样的描述，它是明确的，在设计过程中，电路分析中起着一个非常重要的作用。由于电路分析应用电路模型，执业的工程师尝试使用成熟的电路模型，使设计满足在第一次迭代的设计规范。在这个单元，我们使用20至100年已测试通过机型，你可以认为他们是成熟的。能力模型与实际电力系统理想的电路元件，使电路理论的工程师非常有用的。 说理想电路元件的互连可用于定量预测系统的行为，意味着我们可以用数学方程描述的互连。对于数学方程是有用的，我们必须写他们在衡量的数量方面。在电路的情况下，这些数量是电压和电流。电路分析的研究，包括了解其电压和电流和理解上的电压施加的限制，目前互连的理想元素的每一个理想的电路元件的行为电路分析基础上的电压和电流的变量。电压是每单位电荷，电荷分离所造成的断电和SI单位伏V = DW / DQ。电流是电荷的流动速度和具有的安培SI单位（I= DQ/ DT）。理想的基本电路元件是两个终端组成部分，不能细分，也可以在其终端电压和电流的数学描述。被动签署公约涉及元素，当电流通过元素的参考方向是整个元素的参考电压降的方向端子的电压和电流的表达式使用一个积极的迹象。 功率是单位时间内的能量和平等的端电压和电流的乘积;瓦SI单位。权力的代数符号解释如下： 如果P> 0，电源被传递到电路或电路元件。 如果p<0，权力正在从电路或电路元件中提取。 在这一章中介绍的电路元素是电压源，电流源和电阻器。理想电压源保持一个规定的电压，不论当前的设备。理想电流源保持规定的电流不管了整个设备的电压。电压和电流源是独立的，也就是说，不是任何其他电路的电流或电压的影响;或依赖，就是由一些电路中的电流或电压。一个电阻制约了它的电压和电流成正比彼此。有关的比例常数电压和一个电阻值称为其电阻和欧姆测量。 欧姆定律建立相称的电压和电流的电阻。具体来说，V = IR电阻的电流流动，如果在它两端的电压下降，或V=_IR方向，如果在该电阻的电流流是在它两端的电压上升方向。 通过结合对权力的方程，P = VI，欧姆定律，我们可以判断一个电阻吸收的功率：P = I2R= U2/ R 电路节点和封闭路径。节点是一个点，两个或两个以上的电路元件加入。当只有两个元素连接，形成一个节点，他们表示将在系列。一个闭合的路径是通过连接元件追溯到一个循环，起点和终点在同一节点，只有一次每遇到中间节点。 电路是说，要解决时，两端的电压，并在每个元素的电流已经确定。欧姆定律是一个重要的方程，得出这样的解决方案。 在简单的电路结构，欧姆定律是足以解决两端的电压，目前在每一个元素。然而，对于更复杂的互连，我们需要使用两个更为重要的代数关系，被称为基尔霍夫定律，来解决所有的电压和电流。 基尔霍夫电流定律是： 在电路中的任何一个节点电流的代数和等于零。 基尔霍夫电压定律是： 电路中的任何封闭路径上的电压的代数和等于零。 1.2电路分析技术 到目前为止，我们已经分析应用结合欧姆定律基尔霍夫定律电阻电路相对简单。所有的电路，我们可以使用这种方法，但因为他们而变得结构更为复杂，涉及到越来越多的元素，这种直接的方法很快成为累赘。在这一课中，我们介绍两个电路分析的强大的技术援助：在复杂的电路结构的分析节点电压的方法，并网电流的方
机械工程外文翻译(适用于毕业论文外文翻译+中英文对照)
Mechanical engineering 1.The porfile of mechanical engineering Engingeering is a branch of mechanical engineerig,it studies mechanical and power generation especially power and movement. 2.The history of mechanical engineering 18th century later periods,the steam engine invention has provided a main power fountainhead for the industrial revolution,enormously impelled each kind of mechznicalbiting.Thus,an important branch of a new Engineering –separated from the civil engineering tools and machines on the branch-developed together with Birmingham and the establishment of the Associantion of Mechanical Engineers in 1847 had been officially recognized.The mechanical engineering already mainly used in by trial and error method mechanic application technological development into professional engineer the scientific method of which in the research,the design and the realm of production used .From the most broad perspective,thedemend continuously to enhance the efficiencey of mechanical engineers improve the quality of work,and asked him to accept the history of the high degree
机械设计制造及其自动化外文翻译外文文献英文文献普通钻床改造为多轴钻床复习过程
普通钻床改造为多轴钻床 目前，我国中、小型企业的产品质量和生产效率都需要有一个新的提高, 但是加工手段却远远不能满足需要, 许多中小型企业都结合自己的实际对设备的技术状态进行改进，通过强化自身, 以求自我发展普通钻床为单轴机床，但安装上多轴箱就会成为多轴的钻床，改造成多轴钻床后，能大大地缩短加工时间，提高生产效率。 多轴加工应用：据统计，一般在车间中普通机床的平均切削时间很少超过全部工作时间的15%。其余时间是看图、装卸工件、调换刀具、操作机床、测量以及清除铁屑等等。使用 数控机床虽然能提高85%，但购置费用大。某些情况下，即使生产率高，但加工相同的零件，其成本不一定比普通机床低。故必须更多地缩短加工时间。不同的加工方法有不同的特点，就钻削加工而言，多轴加工是一种通过少量投资来提高生产率的有效措施。 多轴加工优势：虽然不可调式多轴头在自动线中早有应用，但只局限于大批量生产。即使采用可调式多轴头扩大了使用范围，仍然远不能满足批量小、孔型复杂的要求。尤其随着工业的发展，大型复杂的多轴加工更是引人注目。例如原子能发电站中大型冷凝器水冷壁管板有15000个“ 20孔，若以摇臂钻床加工，单单钻孔与锪沉头孔就要842.5小时，另外还要 划线工时151.1 小时。但若以数控八轴落地钻床加工，钻锪孔只要171.6 小时，划线也简单，只要1.9 小时。因此，利用数控控制的二个坐标轴，使刀具正确地对准加工位置，结合多轴加工不但可以扩大加工范围，而且在提高精度的基础上还能大大地提高工效，迅速地制造出原来不易加工的零件。有人分析大型高速柴油机30 种箱形与杆形零件的2000 多个钻孔操作中，有40%可以在自动更换主轴箱机床中用二轴、三轴或四轴多轴头加工，平均可减少20%的加工时间。1975年法国巴黎机床展览会也反映了多轴加工的使用愈来愈多这一趋势。 多轴加工的设备：多轴加工是在一次进给中同时加工许多孔或同时在许多相同或不同工件上各加工一个
信息技术英文缩写与解释
AVI 影音文件Audio Video Interleaved 声音图象交叉存取。AVI是一种微软媒体文件格式，类似于MPEG和QuickTime。在AVI中，声音和图象是交叉的存取在一个文件中的每个段的。 ADSL 非对称数字用户线路 非对称数字用户线路。这种DSL叫做非对称DSL，将成为广大家庭和小型商业客户最熟悉的一种DSL。ADSL之所以叫做非对称是因为它的两个双工通道都用来向用户传输数据。仅有很小一部分带宽用来回送用户的信息。然而，大部Internet 特别是富于图形和多媒体Web 数据需要很大的下传带宽，同时用户信息相对比较少，上传的带宽也不要很大。使用ADSL时，下传的速率可以达到6.1 Mbps，而上传速率也可以达到640 Kbps。高的下传速率意味着您的电话可以传输动画，声音和立体图形。另外，一小部分的带宽可以用来传输语音信号，您可以同时打电话而不用再使用第二条电话线。不象电视线路提供的相同的服务，使用ADSL，您不需要和您的邻居争用带宽。有时候，现有的电话线可以使用ADSL，而有时候却要升级，除非电话公司提供了无分离器的ADSL，您就必须安装一个DSL调制解调器。 ASP (Application Services Provider) 应用服务提供商 是指配置、租赁、管理应用解决方案，它是随着外包趋势、软件应用服务和相关业务的发展而逐渐形成的。ASP具有三大特点：首先，ASP向用户提供的服务应用系统本身的所有权属ASP，用户租用服务之后对应用系统拥有使用权；并且，应用系统被集中放置在ASP的IDC（Internet数据服务中心）中，具有充足的带宽、电力和空间保证以及具有专业质量的系统维护服务；ASP定期向用户收取服务费。应用服务提供商将以全新的方式推动应用服务产业的巨大发展。ATM (Asynchronous Transmission Mode) 异步传输模式 这是为满足宽带综合业务数据通信，在分组交换技术的基础上迅速发展起来的通信新技术。可以实现语音、数据、图像、视频等信号的高速传输。 AI (Artificial Intelligent) 人工智能 是计算机科学的一门研究领域。它试图赋予计算机以人类智慧的某些特点，用计算机来模拟人的推理、记忆、学习、创造等智能特征，主要方法是依靠有关知识进行逻辑推理，特别是利用经验性知识对不完全确定的事实进行的精确性推理。 AD 网上广告 指一则按规定象素尺寸或字节数设定的标语或图像，通常是以动画表现的。 Baseband 基带 在该方式中，电压脉冲直接加到电缆，并且使用电缆的整个信号频率范围。基带与宽带传输相比较，宽带传输中，来自多条信道的无线信号调制到不同的“载波”频率上，带宽被划分为不同信道，每信道上的频率范围一定。LocalTalk及以太网都是基带网络，一次仅传输一个信号，电缆上信号电平的改变表示数字值0或者1。使用电缆的整个带宽建立起两个系统间的通信对话，然后两个系统轮流传送。在此期间，共享电缆的其它系统不能传送。基带传输系统中的直流信号往往由于电阻、电容等因素而衰减。另外马达、荧光灯等电子设备产生的外部电磁干扰也会加快信号的衰减。传输率越高，信号就越容易被衰减。为此，以太网等建网标准规定了网络电缆类型、电缆屏蔽、电缆距离、传输率以及在大部分环境中提供相对无差错服务的有关细节。 BBS (Bulletin Board System) 电子公告板 这是因特网提供的一种信息服务，为用户提供一个公用环境，以使寄存函件，读取通告，参与讨论和交流信息。Bluetooth 蓝牙(一种无线通信的标准) 蓝牙技术涉及一系列软硬件技术、方法和理论，包括：无线通信与网络技术，软件工程、软件可靠性理论，协议的正确性验证、形式化描述和一致性与互联测试技术，嵌入式实时操作系统（Embedded RTOS），跨平台开发和用户界面图形化技术，软/硬件接口技术（如RS232，UART，USB等)，高集成、低功耗芯片技术等。蓝牙的目标是要提供一种通用的无线接口标准，用微波取代传统网络中错综复杂的电缆，在蓝牙设备间实现方便快捷、灵活安全、低成本低功耗的数据和话音通信。因此，其载频选用在全球都可用的2.45GHz ISM（工业、科学、医学）频带。 CA (Certificate Authority）认证中心 是在线交易的监督者和担保人，主要进行电子证书管理、电子贸易伙伴关系建立和确认、密钥管理、为支付系统中的各参与方提供身份认证等。CA类似于现实生活中公证人的角色，具有权威性，是一个普遍可信的第三方。
电力电子技术外文翻译
外文翻译 题目：电力电子技术二 A部分 晶闸管 在晶闸管的工作状态，电流从阳极流向阴极。在其关闭状态，晶闸管可以阻止正向 导电，使其不能运行。 可触发晶闸管能使导通状态的正向电流在短时间内使设备处于阻断状态。使正向电压下降到只有导通状态的几伏（通常为1至3伏电压依赖于阻断电压的速度）。 一旦设备开始进行，闸极电流将被隔离。晶闸管不可能被闸关闭，但是可以作为一个二极管。在电路的中，只有当电流处于消极状态，才能使晶闸管处于关闭状态，且电流降为零。在设备运行的时间内，允许闸在运行的控制状态直到器件在可控时间再次进入正向阻断状态。 在逆向偏置电压低于反向击穿电压时，晶闸管有微乎其微的漏电流。通常晶闸管的正向额定电压和反向阻断电压是相同的。晶闸管额定电流是在最大范围指定RMS和它是有能力进行平均电流。同样的对于二极管，晶闸管在分析变流器的结构中可以作为理想的设备。在一个阻性负载电路中的应用中，可以控制运行中的电流瞬间传至源电压的正半周期。当晶闸管尝试逆转源电压变为负值时，其理想化二极管电流立刻变成零。 然而，按照数据表中指定的晶闸管，其反向电流为零。在设备不运行的时间中，电流为零，重要的参数变也为零，这是转弯时间区间从零交叉电流电压的参
考。晶闸管必须保持在反向电压，只有在这个时间，设备才有能力阻止它不是处于正向电压导通状态。 如果一个正向电压应用于晶闸管的这段时间已过，设备可能因为过早地启动并有可能导致设备和电路损害。数据表指定晶闸管通过的反向电压在这段期间和超出这段时间外的一个指定的电压上升率。这段期间有时被称为晶闸管整流电路的周期。 根据使用要求，各种类型的晶闸管是可得到的。在除了电压和电流的额定率，转弯时间，和前方的电压降以及其他必须考虑的特性包括电流导通的上升率和在关闭状态的下降率。 1。控制晶闸管阶段。有时称为晶闸管转换器，这些都是用来要是整顿阶段，如为直流和交流电机驱动器和高压直流输电线路应用的电压和电流的驱动。主要设备要求是在大电压、电流导通状态或低通态压降中。这类型的晶闸管的生产晶圆直径到10厘米，其中平均电流目前大约是4000A，阻断电压为5之7KV。 2。逆变级的晶闸管。这些设计有小关断时间，除了低导通状态电压，虽然在设备导通状态电压值较小，可设定为2500V和1500A。他们的关断时间通常在几微秒范围到100μs之间，取决于其阻断电压的速率和通态压降。 3。光控晶闸管。这些会被一束脉冲光纤触发使其被引导到一个特殊的敏感的晶闸管地区。光化的晶闸管触发，是使用在适当波长的光的对硅产生多余的电子空穴。这些晶闸管的主要用途是应用在高电压，如高压直流系统，有许多晶闸管被应用在转换器阀门上。光控晶闸管已经发现的等级，有4kV的3kA，导通状态电压2V、光触发5毫瓦的功率要求。 还有其它一些晶闸管，如辅助型关断晶闸管（关贸总协定），这些晶闸管其他变化，不对称硅可控（ASCR）和反向进行，晶闸管（RCT）的。这些都是应用。 B部分 功率集成电路 功率集成电路的种类 现代半导体功率控制相当数量的电路驱动，除了电路功率器件本身。这些控制电路通常由微处理器控制，其中包括逻辑电路。这种在同一芯片上包含或作
机械类外文翻译
机械类外文翻译 塑料注塑模具浇口优化 摘要:用单注塑模具浇口位置的优化方法，本文论述。该闸门优化设计的目的是最大限度地减少注塑件翘曲变形，翘曲，是因为对大多数注塑成型质量问题的关键，而这是受了很大的部分浇口位置。特征翘曲定义为最大位移的功能表面到表面的特征描述零件翘曲预测长度比。结合的优化与数值模拟技术，以找出最佳浇口位置，其中模拟armealing算法用于搜索最优。最后，通过实例讨论的文件，它可以得出结论，该方法是有效的。 注塑模具、浇口位臵、优化、特征翘曲变形关键词: 简介 塑料注射成型是一种广泛使用的，但非常复杂的生产的塑料产品，尤其是具有高生产的要求，严密性，以及大量的各种复杂形状的有效方法。质量ofinjection 成型零件是塑料材料，零件几何形状，模具结构和工艺条件的函数。注塑模具的一个最重要的部分主要是以下三个组件集:蛀牙，盖茨和亚军，和冷却系统。拉米夫定、Seow(2000)、金和拉米夫定(2002) 通过改变部分的尼斯达到平衡的腔壁厚度。在平衡型腔充填过程提供了一种均匀分布压力和透射电镜,可以极大地减少高温的翘曲变形的部分～但仅仅是腔平衡的一个重要影响因素的一部分。cially Espe,部分有其功能上的要求,其厚度通常不应该变化。 pointview注塑模具设计的重点是一门的大小和位臵,以及流道系统的大小和布局。大门的大小和转轮布局通常被认定为常量。相对而言,浇口位臵与水口大小布局也更加灵活,可以根据不同的零件的质量。 李和吉姆(姚开屏,1996a)称利用优化流道和尺寸来平衡多流道系统为multiple 注射系统。转轮平衡被形容为入口压力的差异为一多型腔模具用相同的蛀牙,也存
文献翻译-机械加工中心
附录1 中文名称：机械加工中心英文名称：machining center 其他名称：自动换刀数控机床 定义：能自动更换工具，对一次装夹的工件进行多工序加工的数控机床。机械加工中心,简称cnc，是由机械设备与数控系统组成的使用于加工复杂形状工件的高效率自动化机床。加工中心又叫电脑锣。加工中心备有刀库，具有自动换刀功能，是对工件一次装夹后进行多工序加工的数控机床。加工中心是高度机电一体化的产品，工件装夹后，数控系统能控制机床按不同工序自动选择、更换刀具、自动对刀、自动改变主轴转速、进给量等，可连续完成钻、镗、铣、铰、攻丝等多种工序，因而大大减少了工件装夹时间、测量和机床调整等辅助工序时间，对加工形状比较复杂，精度要求较高，品种更换频繁的零件具有良好的经济效果。按控制轴数可分为：（1）三轴加工中心 （2）四轴加工中心 （3）五轴加工中心。 项目二机械加工中心设备技术分类加工中心的品种、规格较多，这里仅从结构上对其作一分类。 一、立式加工中心指主轴轴线为垂直状态设置的加工中心。其结构形式多为固定立柱式，工作台为长方形，无分度回转功能，适合加工盘、套、板类零件。一般具有三个直线运动坐标，并可在工作台上安装一个水平轴的数控回转台，用以加工螺旋线零件。立式加工中心装夹工件方便，便于操作，易于观察加工情况，但加工时切屑不易排除，且受立柱高度和换刀装置的限制，不能加工太高的零件。立式加工中心的结构简单，占地面积小，价格相对较低，应用广泛。 二、卧式加工中心指主轴轴线为水平状态设置的加工中心。通常都带有可进行分度回转运动的工作台。卧式加工中心一般都具有三个至五个运动坐标，常见的是三个直线运动坐标加一个回转运动坐标，它能够使工件在一次装夹后完成除安装面和顶面以外的其余四个面的加工，最适合加工箱体类零件。卧式加工中心调试程序及试切时不便观察，加工时不便监视，零件装夹和测量不方便，但加工时排屑容易，对加工有利。与立式加工中心相比，卧式加工中心的结构复杂，占地面积大，价格也较高。
机械设计外文翻译(中英文)
机械设计理论 机械设计是一门通过设计新产品或者改进老产品来满足人类需求的应用技术科学。它涉及工程技术的各个领域，主要研究产品的尺寸、形状和详细结构的基本构思，还要研究产品在制造、销售和使用等方面的问题。 进行各种机械设计工作的人员通常被称为设计人员或者机械设计工程师。机械设计是一项创造性的工作。设计工程师不仅在工作上要有创造性，还必须在机械制图、运动学、工程材料、材料力学和机械制造工艺学等方面具有深厚的基础知识。如前所诉，机械设计的目的是生产能够满足人类需求的产品。发明、发现和科技知识本身并不一定能给人类带来好处，只有当它们被应用在产品上才能产生效益。因而，应该认识到在一个特定的产品进行设计之前，必须先确定人们是否需要这种产品。 应当把机械设计看成是机械设计人员运用创造性的才能进行产品设计、系统分析和制定产品的制造工艺学的一个良机。掌握工程基础知识要比熟记一些数据和公式更为重要。仅仅使用数据和公式是不足以在一个好的设计中做出所需的全部决定的。另一方面，应该认真精确的进行所有运算。例如，即使将一个小数点的位置放错，也会使正确的设计变成错误的。 一个好的设计人员应该勇于提出新的想法，而且愿意承担一定的风险，当新的方法不适用时，就使用原来的方法。因此，设计人员必须要有耐心，因为所花费的时间和努力并不能保证带来成功。一个全新的设计，要求屏弃许多陈旧的，为人们所熟知的方法。由于许多人墨守成规，这样做并不是一件容易的事。一位机械设计师应该不断地探索改进现有的产品的方法，在此过程中应该认真选择原有的、经过验证的设计原理，将其与未经过验证的新观念结合起来。 新设计本身会有许多缺陷和未能预料的问题发生，只有当这些缺陷和问题被解决之后，才能体现出新产品的优越性。因此，一个性能优越的产品诞生的同时，也伴随着较高的风险。应该强调的是，如果设计本身不要求采用全新的方法，就没有必要仅仅为了变革的目的而采用新方法。 在设计的初始阶段，应该允许设计人员充分发挥创造性，不受各种约束。即使产生了许多不切实际的想法，也会在设计的早期，即绘制图纸之前被改正掉。只有这样，才不致于堵塞创新的思路。通常，要提出几套设计方案，然后加以比较。很有可能在最后选定的方案中，采用了某些未被接受的方案中的一些想法。
通信工程外文翻译---一点多址扩频通信系统的应用
【附录】 英文文献 The Application of one point Multiple Access Spread Spectrum Communication System Liu Jiangang, Nanyang City, HenanProvince Electric Power Industry Bureau 【ABSTRACT】Spread Spectrum Digital Microwave communication as a communication, because their excellent performance have been widely used. The article in Nanyang City Power Industry Bureau one point Multiple Access Spread Spectrum Communication System as an example.briefed the spread spectrum communications, the basic concept and characteristics of the power system communication applications .KEYWORDS：one point multiple access; Spread-spectrum communication; Attenuation Nanyang City in the outskirts of Central cloth 35 to 11 kv substation farm terminals, their operation management rights belong to the Council East, Rural Power Company west (the eastern suburb of agricultural management companies -- four, the western suburbs of Rural Power Company Management 7), Scheduling of the various stations of the means of communication to the original M-150 radio and telephone posts. 2002 With the transformation of rural network, the remote station equipment into operation and communication channels to put a higher demand .As PUC Dispatch Communication Building to the east and west of farmers -- the difference between a company linked to fiber, Therefore, if 11 substations and the establishment of a transfer Link Building links Point may be the data and voice were sent to two rural power companies dispatch room, Rural Network scheduling for the implementation of automation to create the necessary conditions. Given the status and power grid substation level, nature, taking into account the carrier and optical-fiber communications to conduct multiple forwarding, increasing the instability factor, considering the cost and conditions of the urban construction, Finally decided to adopt wireless spread-spectrum technology to establish that 11
电动汽车电子技术中英文对照外文翻译文献
(文档含英文原文和中文翻译) 中英文资料外文翻译 原文： As the world energy crisis, and the war and the energy consumption of oil -- and are full of energy, in one day, someday it will disappear without a trace. Oil is not in resources. So in oil consumption must be clean before finding a replacement. With the development of science and technology the progress of
the society, people invented the electric car. Electric cars will become the most ideal of transportation. In the development of world each aspect is fruitful, especially with the automobile electronic technology and computer and rapid development of the information age. The electronic control technology in the car on a wide range of applications, the application of the electronic device, cars, and electronic technology not only to improve and enhance the quality and the traditional automobile electrical performance, but also improve the automobile fuel economy, performance, reliability and emissions purification. Widely used in automobile electronic products not only reduces the cost and reduce the complexity of the maintenance. From the fuel injection engine ignition devices, air control and emission control and fault diagnosis to the body auxiliary devices are generally used in electronic control technology, auto development mainly electromechanical integration. Widely used in automotive electronic control ignition system mainly electronic control fuel injection system, electronic control ignition system, electronic control automatic transmission, electronic control (ABS/ASR) control system,
机械类英文文献+翻译)
机械工业出版社2004年3月第1版 20.9 MACHINABILITY The machinability of a material usually defined in terms of four factors: 1、Surface finish and integrity of the machined part; 2、Tool life obtained; 3、Force and power requirements; 4、Chip control. Thus, good machinability good surface finish and integrity, long tool life, and low force And power requirements. As for chip control, long and thin (stringy) cured chips, if not broken up, can severely interfere with the cutting operation by becoming entangled in the cutting zone. Because of the complex nature of cutting operations, it is difficult to establish relationships that quantitatively define the machinability of a material. In manufacturing plants, tool life and surface roughness are generally considered to be the most important factors in machinability. Although not used much any more, approximate machinability ratings are available in the example below. 20.9.1 Machinability Of Steels Because steels are among the most important engineering materials (as noted in Chapter 5), their machinability has been studied extensively. The machinability of steels has been mainly improved by adding lead and sulfur to obtain so-called free-machining steels. Resulfurized and Rephosphorized steels. Sulfur in steels forms manganese sulfide inclusions (second-phase particles), which act as stress raisers in the primary shear zone. As a result, the chips produced break up easily and are small; this improves machinability. The size, shape, distribution, and concentration of these inclusions significantly influence machinability. Elements such as tellurium and selenium, which are both chemically similar to sulfur, act as inclusion modifiers in resulfurized steels. Phosphorus in steels has two major effects. It strengthens the ferrite, causing