模具专业英语1
模具专业英语
gate：进胶
gate location：进胶位
gate size：胶口尺寸
gate type：胶口形式
switching runner/gate：转水口edge gate：大水口（侧进胶）
pin-point gate：细水口
sprue diameter：直接进胶
cashew/banana gate：牛角/香蕉进胶sub/tunnel gate：潜水进胶
fan gate：扇形进胶
tab gate：搭接/边进胶
hot runner system：热流道runner：流道/水口
cavity：前模
core：后模
slide：行位
insert：镶件
lifter：斜顶
buffle：隔水片
stop pin：垃圾钉
core pin：镶钉
location ring：定位圈
ejector pin：顶针
ejector sleeve：司筒
stripper plate：推板（脱料板）leader pin：导柱
guide pin：中托边
dowel pin：销钉
return pin：回针
wedge：铲基
wear plate：耐磨块
stop plate：挡板
support pillar：撑头
shut-off：枕位
switch：转换开关
micro-switch：微转换开关
inter-lock：互锁
lock：边锁
interchangeable inserts：互换镶件spring：弹簧
clearance：避空
steel safety：预留
thickness/wall：壁厚（胶位）gloss：光滑
gloss shine/shinny：太光
no flash：没批风
no burr：没批风（用于五金件中）
drill through：通孔
tap：攻牙
thread：攻牙
blind：盲孔
finish：表面要求polish：抛光
texture：晒纹
engrave：雕刻
laser engrave：激光雕刻flush：面面平齐
off-set：偏移
flow mark：料花
sweat out：冒汗shrinkage：缩水率
sink：缩水deformation：变形wrap：反变形
water line：运水
break edge：去毛边gage：量规
resin：胶料
steel：钢料
add steel：减胶
reduce steel：加胶welding：烧焊
wire-cut：线切割
eye-bolt：吊环
Rev.：版本
becu：铍铜
sharp：利角
radius：圆角
tolerance：公差
hydraulic：油缸
clinker：芯
seals：油封
drawing number：图纸编号part number：产品编号part name：产品名称
模具专业英语词汇大全
模具专业英语词汇 A abrasion n. 磨损 abrasion resistance n. 耐磨损性 abrasive n. 磨料 accelerator n. 促进剂 accuracy n. 准确性 accurate die casting 精密压铸 air trap 积风 acrylic n. 丙烯酸 /压克力 ì active plate 活动板 additive n. 添加剂 adhere v. 黏附 adhesion n. 黏合 adhesive n. 胶粘剂 air-cushion eject-rod 气垫顶杆 air cushion plate 气垫板 air entrapment n. 困气 anneal v. 退火 assemble v. 总成 B back pressure 背压 bismuth mold 铋铸模 baffle plate 挡块 barrel n. 机筒 /料筒 / bending block 折刀 bottom block 下垫脚 bottom plate 下托板(底板) bushing bolck 衬套 barrel temperature 料筒温度 blush 发 blank through dies 漏件式落料模 burnishi blow molding n. 吹塑成型 blow molding machine n. 吹塑机 brittle adj. 脆性 bubble n. 气泡 burr 毛刺 button d by-product n. 副产品 C calendering n. 压延 carbon steel n. 碳素钢 casting n. 铸造 catalyst n. 催化剂 cavity n. 型腔 chemical resistance n. 耐化学腐蚀性 chip v. 削 /凿
模具专业英文术语大全
模具英语专业术语 模具述语 一、入水：gate 进入位： gate location 水口形式：gate type 大水口：edge gate 细水口： pin-point gate 水口大小：gate size 转水口： switching runner/gate 唧嘴口径： sprue diameter 二、流道: runner 热流道： hot runner,hot manifold 热嘴冷流道: hot sprue/cold runner 唧嘴直流: direct sprue gate 圆形流道：round(full/half runner 流道电脑分析：mold flow analysis 流道平衡:runner balance 热嘴： hot sprue 热流道板：hot manifold 发热管：cartridge heater 探针: thermocouples 插头： connector plug 插座： connector socket 密封/封料： seal 三、运水：water line 喉塞：line lpug 喉管：tube 塑胶管：plastic tube 快速接头：jiffy quick connector plug/socker 四、模具零件： mold components 三板模：3-plate mold 二板模：2-plate mold 边钉/导边：leader pin/guide pin 边司/导套：bushing/guide bushing 中托司：shoulder guide bushing 中托边L：guide pin 顶针板：ejector retainner plate 托板： support plate 螺丝： screw 管钉：dowel pin 开模槽：ply bar scot 内模管位：core/cavity inter-lock 顶针： ejector pin 司筒：ejector sleeve 司筒针：ejector pin 推板：stripper plate 缩呵：movable core,return core core puller 扣机（尼龙拉勾）：nylon latch lock 斜顶：lifter 模胚（架）： mold base 上内模：cavity insert 下内模：core insert 行位（滑块）： slide 镶件：insert 压座/斜鸡：wedge 耐磨板/油板：wedge wear plate 压条：plate 撑头: support pillar 唧嘴： sprue bushing 挡板：stop plate 定位圈：locating ring 锁扣：latch 扣鸡：parting lock set 推杆：push bar 栓打螺丝：S.H.S.B 顶板：eracuretun 活动臂：lever arm 分流锥：spure sperader 水口司:bush 垃圾钉：stop pin 隔片：buffle 弹弓柱：spring rod 弹弓:die spring 中托司：ejector guide bush 中托边：ejector guide pin 镶针：pin 销子：dowel pin 波子弹弓：ball catch 喉塞: pipe plug
塑胶模具专业英语
中文英文 机工,机器加工 machining,machine work O环,O形封垫 O ring 下料模,切料模 blanking die 寸进,寸动 inching 工程塑胶 engineering plastics 工模,夹具,支架 jig 干胶,粘著剂,动物胶 glue 干燥时间 drying time 干燥剂 drier dryer 不划一颜色,颜色深浅不均 color non-uni formity 中心浇口 center gate 内衬,衬套,衬蛰 liner 公差,容差 tolerance 分模线,合模线,模缝痕 parting line 切口,缺口 notch 切口,缺料 notch 切边(n) shear edge 化学腐蚀 chemical atching 化学腐蚀 chemical etching 反射 reflection 孔隙,空洞,气泡 void 尺寸稳定性 dimensional sability 手动压机 hand press 支管形喷嘴 nozzle manifold 比重 specific gravity 比热 specific heat 毛状裂痕 hair crack,hair cracking 毛绒 fuzz 毛边,凿纹 burr,flash,fin 水道,水通路 water channel 火花放电 spark discharge 火焰处理 flame treatment,flame treating 片材 sheet 凹痕,缩痕 sink mark,shrink mark 凹槽,内陷,凹陷 undercut 加料,给料,供料 feed 加热,加温 warming,warming up 加热板,热板(盘) heating plate 加热管套,加热缸 heating cylinder,heatin g barrel 加热炉 heating furnace 功率,力率 power factor 半透明 semitransparence,translucence 打眼,钻孔 driling 正余面,交叠,重叠 overlap 永久变形 permanent set,residual strain 白昙,雾状 haze 立式射出成型机 vertical injection mo(u)l ding machine 光彩,光泽 gloss 印刷 printing 同轴往复螺杆式射出成型机 in-line scre w(type)injecton mo(u)lding machine 合成树枝 synthetic resin 合板,集成材 composite wood 合模力,开模力 mo(u)ld clamping force, mo(u)ld locking force 合模线,毛边线 flash line,parting line 合模线,毛边线 spew line,spue line 合模销,导销 leader pin 合模销套,导销衬套 leader pin pushing 合模机构,开模机构 mo(u)ld clamping m echanism 后加工 post processing 后加热 after baking 后成型 postforming 回程销,复归销 return pin 安全系数 safety factor 安全门 safety door 成孔销,心型销,模蕊销 core pin 成孔销托板,动或定模板 core pin plate 成形 forming 成形,模制 mo(u)iding,forming
土木工程专业英语词汇(整理版)
第一部分必须掌握，第二部分尽量掌握 第一部分： 1 Finite Element Method 有限单元法 2 专业英语Specialty English 3 水利工程Hydraulic Engineering 4 土木工程Civil Engineering 5 地下工程Underground Engineering 6 岩土工程Geotechnical Engineering 7 道路工程Road (Highway) Engineering 8 桥梁工程Bridge Engineering 9 隧道工程Tunnel Engineering 10 工程力学Engineering Mechanics 11 交通工程Traffic Engineering 12 港口工程Port Engineering 13 安全性safety 17木结构timber structure 18 砌体结构masonry structure 19 混凝土结构concrete structure 20 钢结构steelstructure 21 钢-混凝土复合结构steel and concrete composite structure 22 素混凝土plain concrete 23 钢筋混凝土reinforced concrete 24 钢筋rebar 25 预应力混凝土pre-stressed concrete 26 静定结构statically determinate structure 27 超静定结构statically indeterminate structure 28 桁架结构truss structure 29 空间网架结构spatial grid structure 30 近海工程offshore engineering 31 静力学statics 32运动学kinematics 33 动力学dynamics 34 简支梁simply supported beam 35 固定支座fixed bearing 36弹性力学elasticity 37 塑性力学plasticity 38 弹塑性力学elaso-plasticity 39 断裂力学fracture Mechanics 40 土力学soil mechanics 41 水力学hydraulics 42 流体力学fluid mechanics 43 固体力学solid mechanics 44 集中力concentrated force 45 压力pressure 46 静水压力hydrostatic pressure 47 均布压力uniform pressure 48 体力body force 49 重力gravity 50 线荷载line load 51 弯矩bending moment 52 torque 扭矩53 应力stress 54 应变stain 55 正应力normal stress 56 剪应力shearing stress 57 主应力principal stress 58 变形deformation 59 内力internal force 60 偏移量挠度deflection 61 settlement 沉降 62 屈曲失稳buckle 63 轴力axial force 64 允许应力allowable stress 65 疲劳分析fatigue analysis 66 梁beam 67 壳shell 68 板plate 69 桥bridge 70 桩pile 71 主动土压力active earth pressure 72 被动土压力passive earth pressure 73 承载力load-bearing capacity 74 水位water Height 75 位移displacement 76 结构力学structural mechanics 77 材料力学material mechanics 78 经纬仪altometer 79 水准仪level 80 学科discipline 81 子学科sub-discipline 82 期刊journal ,periodical 83文献literature 84 ISSN International Standard Serial Number 国际标准刊号 85 ISBN International Standard Book Number 国际标准书号 86 卷volume 87 期number 88 专着monograph 89 会议论文集Proceeding 90 学位论文thesis, dissertation 91 专利patent 92 档案档案室archive 93 国际学术会议conference 94 导师advisor 95 学位论文答辩defense of thesis 96 博士研究生doctorate student 97 研究生postgraduate 98 EI Engineering Index 工程索引 99 SCI Science Citation Index 科学引文索引 100ISTP Index to Science and Technology Proceedings 科学技术会议论文集索引 101 题目title 102 摘要abstract 103 全文full-text 104 参考文献reference 105 联络单位、所属单位affiliation 106 主题词Subject 107 关键字keyword 108 ASCE American Society of Civil Engineers 美国土木工程师协会 109 FHWA Federal Highway Administration 联邦公路总署
模具专业英语——注塑模
Injection Mold Technical Terms 特克内克腾目思 （一）模具专业基本用词 Professional Terms Intensification Factor 增强比 Scientific molding 科学注塑英腾次分克深发克偷 塞音特菲克计数器counter康特 Specific Injection Pressure (Psi)特殊注塑压力 思呗色服克 1．塑料—plastic, resin瑞申油管：Oil pipe 尼龙--------nylon 2．样件—sample 调节板-------adjust plate 3．钢料—steel A板--------a plate 4．注塑机—injection machine, press 定位圈----locating ring 喽客厅令 5．产品—part, product, moulding 斜导柱-----angular pin 安给拉PIN 6．模具—mold, mould, tool B板--------- b plate A 简易模（样板模）—prototype mold B 量产用模具—production mold 7．三维造型（数模）—3D model, 滚珠导套-------ball ejector bush 8．二维产品图—2D part drawing 拽应扁顶针--------blade ejector pin 布累得 9．设计—design 低赛应下模板--------bottom clamping plate 抱腾 10．制造—manufacture, 上模型腔------cavity main insert 11．检验—check, 上模镶件------cavity sub insert 12．测量—measure, 妹试司筒针--------center pin 深特 13．修改—change, modify 下模型芯------core main insert 14．工程更改—engineer change 下模镶针------core pin 15．质量—quality 快乐体下模镶件------core sub insert 16．数量—quantity 宽体踢延迟顶针-------delay ejector pin 17．基准—datum, reference 拉杆限位钉--------distance bolt （二）如何解析2D 产品图？How to read 2D part drawing? 一．产品几何Geometry 顶距限位柱--------distance spacer 1．点—point 销钉-------dowel pin 2．线（边）—line, edge 顶块--------ejector bar 3．面face 顶板导套-----ejector leader pin A 侧面—side塞得 B表面—surface射飞思 C 外观面—appearance surface安皮尔思射飞思4．壁厚—wall thickness 我射克来思顶板导柱----ejector leader pin李德拼 5．加强筋（骨位）—rib 瑞布顶针-------ejector pin 6．孔—hole后顶针地板------ejector plate 7．细长的槽—slot 顶针面板-----ejector retain plate 瑞腾 8．柱位—boss 抱死顶棍------ejector rod
(完整版)土木工程专业英语常用词汇
Part IV：Commonly Used Professional Terms of Civil Engineering development organization 建设单位 design organization 设计单位 construction organization 施工单位 reinforced concrete 钢筋混凝土 pile 桩 steel structure 钢结构 aluminium alloy 铝合金 masonry 砌体（工程）reinforced ~ 配筋砌体load-bearing ~ 承重砌体unreinforced ~非配筋砌体 permissible stress (allowable stress) 容许应力plywood 胶合板 retaining wall 挡土墙 finish 装修 finishing material装修材料 ventilation 通风 natural ~ 自然通风 mechanical ~ 机械通风 diaphragm wall (continuous concrete wall) 地下连续墙 villa 别墅 moment of inertia 惯性矩 torque 扭矩 stress 应力normal ~ 法向应力shear ~ 剪应力 strain 应变 age hardening 时效硬化 air-conditioning system空调系统 (air) void ration（土）空隙比 albery壁厨，壁龛 a l mery壁厨，贮藏室 anchorage length锚固长度 antiseismic joint 防震缝 architectural appearance 建筑外观 architectural area 建筑面积 architectural design 建筑设计 fiashing 泛水 workability (placeability) 和易性 safety glass安全玻璃 tempered glass (reinforced glass) 钢化玻璃foamed glass泡沫玻璃 asphalt沥青 felt (malthoid) 油毡 riveted connection 铆接 welding焊接 screwed connection 螺栓连接 oakum 麻刀，麻丝 tee三通管 tap存水弯 esthetics美学 formwork 模板（工程） shoring 支撑 batching 配料 slipform construction (slipforming) 滑模施工 lfit-slab construction 升板法施工 mass concrete 大体积混凝土 terrazzo水磨石 construction joint 施工缝 honeycomb蜂窝，空洞，麻面 piled foundation桩基 deep foundation 深基础 shallow foundation浅基础 foundation depth基础埋深 pad foundation独立基础 strip foundation 条形基础 raft foundation筏基 box foundation箱形基础 BSMT=basement 地下室 lift 电梯electric elevator lift well电梯井 escalator 自动扶梯 Poisson’s ratio 泊松比μ Young’s modulus , modulus of elasticity 杨氏模量，弹性模量E safety coefficient 安全系数 fatigue failure 疲劳破坏 bearing capacity of foundations 地基承载力bearing capacity of a pile 单桩承载力 two-way-reinforcement 双向配筋 reinforced concrete two-way slabs钢筋混凝土双向板 single way slab单向板 window blind 窗帘sun blind wind load 风荷载 curing 养护 watertight concrete 防水混凝土 white cement白水泥 separating of concrete混凝土离折segregation of concrete mortar 砂浆~ joint 灰缝 pilaster 壁柱 fire rating耐火等级 fire brick 耐火砖 standard brick标准砖
生物工程专业英语[整理版]
生物工程专业英语[整理版] Specialized English in Biotechnology This material is dedicated to students majoring in Biotechnology at Hefei University. All rights reserved Contents Lesson 1 What is Biotechnology? ......................................................... ....................... 3 Lesson 2 Where Did Biotechnology Begin? ................................................................ 4 Lesson 3 Brief History of Biotechnology .......................................................... .......... 7 Lesson 4 Dogma, DNA, and Enzymes ................................................................
...... 10 Lesson 5 Polymerase Chain Reaction - Xeroxing DNA ............................................ 12 Lesson 6 Monoclonal Antibody Technology ............................................................. 14 Lesson 7 The Human Genome Project ................................................................ ...... 16 Lesson 8 Whose Genome is It, Anyway?................................................................. .. 19 Lesson 9 Agriculture - An Overview ............................................................... .......... 21 Lesson 10 Gene Gun Speeds Search for New Orchid Colors .................................... 24 Lesson 11 Transforming Plants ................................................................. ................. 26 Lesson 12 Animals and Animal Health ................................................................. ..... 29 Lesson 13 Biomining .............................................................. ................................... 31 Lesson 14 Biofuel ................................................................ ...................................... 32 Lesson 15 New Foods and Food Producers ............................................................... 34 Lesson 16 Blazing a Genetic Trail in Medicine (37) Reading
模具专业英文术语大全
实用文案 模具英语专业术语 模具述语开模槽：ply bar scot 内模管位：一、入水：gate core/cavity inter-lock 顶针：ejector pin 进入位：gate location 司筒：ejector sleeve 水口形式：gate type 司筒针：edge gate ejector pin 大水口：推板：细水口：stripper plate pin-point gate 缩呵：gate size movable core,return core core 水口大小：puller switching runner/gate 转水口：扣机（尼龙拉勾）：nylon latch lock sprue diameter 唧嘴口径：斜顶：lifter : runner 二、流道模胚（架）：mold base hot runner,hot manifold 热流道：上内模：cavity insert : hot sprue/cold runner 热嘴冷流道下内模：core insert : direct sprue gate 唧嘴直流行位（滑块）：slide round(full/half runner 圆形流道：镶件：insert mold flow analysis 流道电脑分析：压座/斜鸡：wedge :runner balance 流道平衡耐磨板/油板：wedge wear plate hot sprue 热嘴：压条：plate hot manifold 热流道板：撑头: support pillar cartridge heater 发热管：唧嘴：sprue bushing : thermocouples 探针挡板：stop plate connector plug 插头：定位圈：locating ring connector socket 插座：锁扣：latch seal 封料：/密封扣鸡：parting lock set water line 三、运水：推杆：push bar line lpug 喉塞：栓打螺丝：S.H.S.B tube 喉管：顶板：eracuretun plastic tube 塑胶管：活动臂：lever arm jiffy quick connector 快速接头：分流锥：spure sperader plug/socker 水口司mold components 四、模具零件：:bush 垃圾钉：三板模：3-plate mold stop pin 隔片：buffle 二板模：2-plate mold 弹弓柱：导边：/leader pin/guide pin spring rod 边钉弹弓:die spring 导套：边司/bushing/guide bushing 中托司：ejector guide bush 中托司：shoulder guide bushing 中托边：ejector guide pin guide pin ：L中托边镶针：ejector retainner plate 顶针板：pin 销子：托板：support plate dowel pin 波子弹弓：ball catch screw 螺丝：: pipe plug dowel pin 管钉：喉塞文案大全． 实用文案 锁模块：lock plate Mold repair 模具维修 angle from pin 斜顶：Molds 模具
生物医学工程专业英语词汇1
probe 探针atrium 中庭，心房（atria ）heart values 心脏瓣膜ventricle 室，心室Doppler shift 多普勒频移 artery 动脉blood flow 血流，血流量 trace 踪迹carotid 颈动脉 physiological 生理的misdiagnosis 误诊 echo sounding 回声探测 gallstones 胆结石breast masses 乳房包块 tumors 肿瘤gray scale 灰度，灰阶spectral 光谱的hand-held 手提式，便携式scanner 扫描仪 clinical 临床的，诊断的Sonography 超声波扫描术platform 平台 chemotherapy 化学疗法Ultrasonic waves 超声波disruptive 破坏的malignant 恶性的，有害的transducer 传感器pulse 脉冲 Disk Storage 磁盘储存器Piezoelectric Effect 压电效应 electric currents 电流crystals 晶体 propagate 传播，传送Receipt 接 extensively 广阔地non-invasive 非侵入性的，非侵入的 congenital 先天性的malformations 畸形
Down syndrome 唐氏症 polydactyl 多指畸形dysmorphia 畸形 cleft lipn. [口腔] 唇裂；[胚][口腔] 兔唇 amplitude 振幅duration 持续Amplification 放大Scan Converter 扫描变换器Vibrate 振动anatomical 解剖的，结构上的 conventional 常见的vibrations 振动共鸣amplifier 放大器compensation 补偿sequence 序列，顺序format 格式，版式 matrix 矩阵matrix 格式修改 storage 存储therapeutic 治疗的blood clots 血栓 kidney stones 肾结石Portability 可移植的 Joint 关节rotating anode旋转阳极fluoroscopic 荧光的 image intensifier图像增强器fluoroscopy 荧光镜检查radiography 放射线照相术electromagnetic [i,lektr?um?ɡ‘netik] adj. 电磁的 radiation [reidi'ei??n] n. 辐射；发光；放射物 Emitted v. 排放（emit的过去分词）；发散 charged particles带电粒子
注塑模具英文论文
Low Cost Injection Mold Creation via Hybrid Additive and Conventional Manufacturing 1. Introduction In most industrial applications, the manufacturing cost of a plastic part is mainly governed by the amount of material used in the molding process. Thus, current approaches for plastic part design and manufacturing focus primarily on establishing the minimum part thickness to reduce material usage. The assumption is that designing the mold and molding processes to the minimum thickness requirement should lead to the minimum manufacturing cost. Nowadays, electronic products such as mobile phones and medical devices are becoming ever more complex and their sizes are continually being reduced. The demand for small and thin plastic components for miniaturization assembly has considerably increased in recent years. Other factors besides minimal material usage may also become important when manufacturing thin plastic components. In particular, for thin parts, the injection molding pressure may become significant and has to be considered in the first phase of manufacturing. Employing current design approaches for plastic parts will fail to produce the true minimum manufacturing cost in these cases. Thus, tackling thin plastic parts requires a new approach, alongside existing mold design principles and molding techniques. 1.1 Current research Today, computer-aided simulation software is essential for the design of plastic parts and molds. Such software increases the efficiency of the design process by reducing the design cost and lead time [1]. Major systems, such as Mold Flow and C-Flow, use finite element analysis to simulate the filling phenomena, including flow patterns and filling sequences. Thus, the molding conditions can be predicted and validated, so that early design modifications can be achieved. Although available software is capable of analyzing the flow conditions, and the stress and the temperature distribution conditions of the component under various molding scenarios, they do not yield design parameters with minimum manufacturing cost [2,3]. The output data of the software only give parameter value ranges for reference and leaves the decision making to the component designer. Several attempts have also been made to optimize the parameters in feeding [4–7], cooling [2,8,9], and ejection These attempts were based on maximizing the flow ability of molten material during the molding process by using empirical relation ships between the product and mold design parameters.
土木工程专业英语原文及翻译
土木工程专业英语原文 及翻译 文档编制序号：[KKIDT-LLE0828-LLETD298-POI08]
08 级土木(1) 班课程考试试卷 考试科目专业英语 考试时间 学生姓名 所在院系土木学院 任课教师 徐州工程学院印制 Stability of Slopes Introduction Translational slips tend to occur where the adjacent stratum is at a relatively shallow depth below the surface of the slope:the failure surface tends to be plane and roughly parallel to the slips usually occur where the adjacent stratum is at greater depth，the failure surface consisting of curved and plane sections． In practice, limiting equilibrium methods are used in the analysis of slope stability. It is considered that failure is on the point of occurring along an assumed or a known failure surface．The shear strength required to maintain a condition of limiting equilibrium is compared with the available shear strength of the soil，giving the average factor of safety along the failure surface．The problem is considered in two dimensions，conditions of plane strain being assumed．It has been shown that a two-dimensional analysis gives a conservative result for a failure on a three-dimensional(dish-shaped) surface． Analysis for the Case of φu =0 This analysis, in terms of total stress，covers the case of a fully saturated clay under undrained conditions, . For the condition immediately after construction．Only moment equilibrium is considered in the analysis．In section, the potential failure surface is assumed to be a circular arc. A trial failure surface(centre O，radius r and length L a where F is the factor of safety with respect to shear strength．Equating moments about O：