几个很有用的CAD程序

1.计算所有线段总长度(加载后只需框选所有线段便可得出这些线段的总长度)
(defun c:LL ()
(setvar "cmdecho" 1)
(setq en (ssget (list '(0 . "spline,arc,line,ellipse,LWPOLYLINE"))))
(setq i 0)
(setq ll 0)
(repeat (sslength en)
(setq ss (ssname en i))
(setq endata (entget ss))
(command "lengthen" ss "")
(setq dd (getvar "perimeter"))
(setq ll (+ dd ll))
(setq i (1+ i))
)
(princ "所选线条总长为：")(princ ll)(princ)
)

2.标注所有线段(加载后只需框选所有线段便可得标注这些线段)
(defun c:LLL ()
(COMMAND "UCS" "")
(setvar "cmdecho" 1)
(SETVAR "OSMODE" 0)
(setq AcadObject (vlax-get-acad-object)
AcadDocument (vla-get-ActiveDocument Acadobject)
mSpace (vla-get-ModelSpace Acaddocument)
)
;;选取需要测量的样条曲线、圆弧、直线、椭圆
(setq en (ssget (list '(0 . "spline,arc,line,ellipse,LWPOLYLINE"))))
(setq i 0)
;;获取系统参数textsize
(setq shh (getvar "textsize"))
(setq str_hh (strcat "\n文字高度 <" (rtos shh 2) ">: "))
(setq hh (getdist str_hh))
(while hh
(setvar "textsize" hh)
(setq hh nil))
;;输入标注文字高度
;;循环开始
(repeat (sslength en)
(setq ss (ssname en i))
(setq endata (entget ss))
(command "lengthen" ss "")
(setq dd (getvar "perimeter"))
(princ (strcat "\n长度=" (rtos dd 2)))
;;寻找代表图层的字符串
(setq aa (assoc 0 endata))
;;获取图层名称
(setq aa1 (cdr aa))
;;判断线条种类
(cond
((= aa1 "SPLINE")
;;如果是spline
(progn
(setq arcObj (VLAX-ENAME->VLA-OBJECT ss))
(setq startPnt1 (vla-get-ControlPoints arcObj))
(setq p1
(vlax-safearray->list (vlax-variant-value startPnt1))
)
(setq x1 (car p1))
(setq y1 (cadr p1))
(setq z1 (caddr p1))
(setq pp1 (list x1 y1 z1))
(repeat (- (/ (length p1) 3) 1)
;;循环，寻找最后一个控制点
(setq p1 (cdddr p1))
(setq x2 (car p1))
(setq y2 (cadr p1))
(setq z2 (caddr p1))
)
(setq pp2 (list x2 y2 z2))
)
)
((= aa1 "LWPOLYLINE")
;;如果是LWPOLYLINE
(progn
(setq arcObj (VLAX-ENAME->VLA-OBJECT ss))
(setq startPnt1 (vla-get-Coordinates arcObj))
(setq p1
(vlax-safearray->list (vlax-variant-value startPnt1))
)
(setq x1 (car p1))
(setq y1 (cadr p1))
(setq z1 (caddr p1))
(setq pp1 (list x1 y1 z1))
(repeat (- (/ (length p1) 3) 1)
;;循环，寻找最后一个控制点
(setq p1 (cdddr p1))
(setq x2 (car p1))
(setq y2 (cadr p1))
(setq z2 (caddr p1))
)
(setq pp2 (list x2 y2 z2))
)
)
(t
;;如果是其他种类线条
(progn
(setq arcObj (VLAX-ENAME->VLA-OBJECT ss))
(setq startPnt1 (vla-get-StartPoint arcObj))
;;获取起点
(setq endPnt1 (vla-get-EndPoint arcObj))
;;获取终点
(setq pp1
(vlax-safearray->list (vlax-v

ariant-value startPnt1))
)
(setq
pp2 (vlax-safearray->list (vlax-variant-value endPnt1))
)
)
)
)
(setq x1 (car pp1))
(setq y1 (cadr pp1))
(setq z1 (caddr pp1))
(setq x2 (car pp2))
(setq y2 (cadr pp2))
(setq z2 (caddr pp2))
(setq x (/ (+ x1 x2) 2))
(setq y (/ (+ y1 y2) 2))
(setq z (/ (+ z1 z2) 2))
(setq pt (list x y z))
;;取得线段两端的中点
(setq ang (angle pp1 pp2))
;;获取角度
(if (> (* (/ ang pi) 180) 180)
(setq ang (+ ang pi))
)
(command "text"
"j"
"bc"
pt
""
(* (/ ang pi) 180)
(strcat "" (rtos dd 2))
""
)
(setq i (1+ i))
)
(prin1)
)
(prompt "\n <>在图中直接写出长度")
(prin1)

3.连续打断程序
(defun c:br1 ()
(command "break" pause "f" pause "@")
)

4.将CAD文字导入Excel表格
(defun c:Q2()
(setq ffn (getfiled "写出文件" "" "xls" 1))
(princ "\n选取文字...")
(setq ss (ssget))
(setq ff (open ffn "w"))
(setq i 0)
(repeat (sslength ss)
(setq ssn (ssname ss i))
(setq ssdata (entget ssn))
(setq sstyp (cdr (assoc 0 ssdata)))
(if (or (= sstyp "TEXT") (= sstyp "MTEXT"))
(progn
(setq txt (cdr (assoc 1 ssdata)))
(princ txt ff)
(princ "\n" ff)
)
)
(setq i (1+ i))
)
(close ff)
(princ (strcat "\n写出文件: " ffn))
(prin1)
)

5 删除带颜色图元

以下程序在别人的贴子里贴过.为了说明问题,今天再贴一次.
改颜色的LISP程序

(defun c:c1()(ssget)(command "chprop" "p" "" "c" "1" "") (princ))
(defun c:c2()(ssget)(command "chprop" "p" "" "c" "2" "") (princ))
(defun c:c3()(ssget)(command "chprop" "p" "" "c" "3" "") (princ))
(defun c:c4()(ssget)(command "chprop" "p" "" "c" "4" "") (princ))
(defun c:c5()(ssget)(command "chprop" "p" "" "c" "5" "") (princ))
(defun c:c6()(ssget)(command "chprop" "p" "" "c" "6" "") (princ))
(defun c:c7()(ssget)(command "chprop" "p" "" "c" "7" "") (princ))
(defun c:c8()(ssget)(command "chprop" "p" "" "c" "8" "") (princ))

你用C1 命令就可以将图元改为红色了.其余类似.

删除红色图元

(defun C:D1 (/ m A M)
(setq m:err *error* *error* *merr*)
(setvar "cmdecho" 0)
(command "UNDO" "G")
(prompt "选择图形")
(setq A (ssget '((62 . 1)) ))
(if (/= A nil)(progn
(setq M (sslength A))
(command "erase" A "")
(princ "\n共删除红色图元<")(princ M)(princ ">个")
))
(command "UNDO" "E")
(princ) )

这样,键入 D1 命令,就可以删除红色的图元了.