模具英语术语
die 模具
figure file, chart file图档
cutting die, blanking die冲裁模
progressive die, follow (-on)die 连续模compound die复合模
punched hole冲孔
panel board镶块
to cutedges=side cut=side scrap切边
to bending折弯
to pull, to stretch拉伸
Line streching, line pulling线拉伸
engraving, to engrave刻印
upsiding down edges翻边
to stake铆合
design modification设计变化
die block模块
folded block折弯块
sliding block滑块
location pin定位销
lifting pin顶料销
die plate, front board模板
padding block垫块
stepping bar垫条
upper die base上模座
lower die base下模座
upper supporting blank上承板
upper padding plate blank上垫板
spare dies模具备品
spring 弹簧
bolt螺栓
plate电镀
mold成型
material for engineering mold testing工程试模材料not included in physical inventory不列入盘点incoming material to be inspected进货待验
PCE assembly production schedule sheet
PCE组装厂生产排配表
model机锺
work order工令
revision版次
production control confirmation生产确认checked by初审
approved by核准
stock age analysis sheet
库存货龄分析表
on-hand inventory现有库存
available material良品可使用
obsolete material良品已呆滞
to be inspected or reworked
待验或重工
cause description原因说明
part number/ P/N 料号
item/group/class类别
prepared by制表
year-end physical inventory difference analysis sheet
年终盘点差异分析表
physical inventory盘点数量
physical count quantity帐面数量
difference quantity差异量
good product/accepted goods/ accepted parts/good parts良品defective product/non-good parts不良品
disposed goods处理品
on way location在途仓
oversea location海外仓
spare parts physical inventory list备品盘点清单
spare molds location模具备品仓
skid/pallet栈板
tox machine自铆机
wire EDM线割
EDM放电机
coil stock卷料
sheet stock片料
tolerance工差
score=groove压线
cam block滑块
pilot导正筒
trim剪外边
pierce剪内边
drag form压锻差
pocket for the punch head挂钩槽
slug hole废料孔
feature die公母模
expansion dwg展开图
radius半径
shim(wedge)楔子
torch-flame cut火焰切割
set screw止付螺丝
form block折刀
stop pin定位销
round pierce punch=die button圆冲子shape punch=die insert异形子
stock locater block定位块
under cut=scrap chopper清角
active plate活动板
baffle plate挡块
cover plate盖板
male die公模
female die母模
groove punch压线冲子
air-cushion eject-rod气垫顶杆spring-box eject-plate弹簧箱顶板bushing block衬套
insert 入块
capability能力
parameter参数
factor系数
phosphate皮膜化成
viscosity涂料粘度
alkalidipping脱脂
main manifold主集流脉
bezel斜视规
blanking穿落模
dejecting顶固模demagnetization去磁;消磁
high-speed transmission高速传递heat dissipation热传
rack上料
degrease脱脂
rinse水洗
alkaline etch龄咬
desmut剥黑膜
D.I. rinse纯水次
Chromate铬酸处理
Anodize阳性处理
seal封孔
revision版次
part number/P/N料号
good products良品
scraped products报放心品defective products不良品
finished products成品
disposed products处理品
barcode条码
flow chart流程表单
assembly组装
stamping冲压
molding成型
spare parts=buffer备品coordinate座标
dismantle the die折模
auxiliary fuction辅助功能
poly-line多义线
heater band 加热片thermocouple热电偶
sand blasting喷沙
grit 砂砾
derusting machine除锈机degate打浇口
dryer烘干机
induction感应
induction light感应光
response=reaction=interaction感应ram连杆
edge finder巡边器
concave凸
convex凹
short射料不足
nick缺口
speck瑕疵
shine亮班
splay 银纹
gas mark焦痕
delamination起鳞
cold slug冷块
blush 导色
gouge沟槽;凿槽
satin texture段面咬花
witness line证示线
patent专利
grit沙砾
granule=peuet=grain细粒
grit maker抽粒机
cushion缓冲
magnalium镁铝合金magnesium镁金
metal plate钣金
lathe车
mill锉
plane刨
grind磨
drill铝
boring镗
blinster气泡
fillet镶;嵌边
through-hole form通孔形式voller pin formality滚针形式cam driver铡楔
shank摸柄
crank shaft曲柄轴
augular offset角度偏差
velocity速度
production tempo生产进度现状torque扭矩
spline=the multiple keys花键quenching淬火
tempering回火
annealing退火
carbonization碳化
alloy合金
tungsten high speed steel钨高速的moly high speed steel钼高速的organic solvent有机溶剂bracket小磁导
liaison联络单
volatile挥发性
resistance电阻
ion离子
titrator滴定仪
beacon警示灯
coolant冷却液
crusher破碎机
模具工程类
plain die简易模
pierce die冲孔模
forming die成型模
progressive die连续模
gang dies复合模
shearing die剪边模
riveting die铆合模
pierce冲孔
forming成型(抽凸,冲凸)
draw hole抽孔
bending折弯
trim切边
emboss凸点
dome凸圆
semi-shearing半剪
stamp mark冲记号
deburr or coin压毛边
punch riveting冲压铆合
side stretch侧冲压平
reel stretch卷圆压平
groove压线
blanking下料
stamp letter冲字(料号) shearing剪断
tick-mark nearside正面压印
tick-mark farside反面压印
冲压名称类
extension dwg展开图procedure dwg工程图
die structure dwg模具结构图material材质
material thickness料片厚度press specification冲床规格
die height range适用模高
die height闭模高度
burr毛边
gap间隙
punch wt.上模重量
五金零件类
inner guiding post内导柱
inner hexagon screw内六角螺钉dowel pin固定销
coil spring弹簧
lifter pin顶料销
eq-height sleeves=spool等高套筒pin销
lifter guide pin浮升导料销guide pin导正销
wire spring圆线弹簧
outer guiding post外导柱
stop screw止付螺丝
located pin定位销
outer bush外导套
模板类
top plate上托板(顶板)
top block上垫脚
punch set上模座
punch pad上垫板
punch holder上夹板
stripper pad脱料背板
up stripper上脱料板
male die公模(凸模)
feature die公母模
female die母模(凹模)
upper plate上模板
lower plate下模板
die pad下垫板
die holder下夹板
die set下模座
bottom block下垫脚
bottom plate下托板(底板) stripping plate内外打(脱料板) outer stripper外脱料板
inner stripper内脱料板
lower stripper下脱料板
零件类
punch冲头
insert入块(嵌入件) deburring punch压毛边冲子groove punch压线冲子stamped punch字模冲子round punch圆冲子
special shape punch异形冲子bending block折刀
roller滚轴
baffle plate挡块
located block定位块supporting block for location 定位支承块
air cushion plate气垫板
air-cushion eject-rod气垫顶杆
trimming punch切边冲子
stiffening rib punch = stinger 加强筋冲子ribbon punch压筋冲子
reel-stretch punch卷圆压平冲子
guide plate定位板
sliding block滑块
sliding dowel block滑块固定块
active plate活动板
lower sliding plate下滑块板
upper holder block上压块
upper mid plate上中间板
spring box弹簧箱
spring-box eject-rod弹簧箱顶杆
spring-box eject-plate弹簧箱顶板bushing bolck衬套
cover plate盖板
guide pad导料块
塑件&模具相关英文
compre sion molding压缩成型
flash mold溢流式模具
plsitive mold挤压式模具
split mold分割式模具
cavity型控母模
core模心公模
taper锥拔
leather cloak仿皮革
shiver饰纹
flow mark流痕
welding mark溶合痕
post screw insert螺纹套筒埋值
self tapping screw自攻螺丝
striper plate脱料板
piston活塞
cylinder汽缸套
chip细碎物
handle mold手持式模具
(移转成型用模具)
encapsulation molding低压封装成型(射出成型用模具)
two plate两极式(模具)
well type蓄料井
insulated runner绝缘浇道方式
hot runner热浇道
runner plat浇道模块
valve gate阀门浇口
band heater环带状的电热器spindle阀针
spear head刨尖头
slag well冷料井
cold slag冷料渣
air vent排气道
welding line熔合痕
eject pin顶出针
knock pin顶出销
return pin回位销反顶针
sleave套筒
stripper plate脱料板
insert core放置入子
runner stripper plate浇道脱料板guide pin导销
eject rod (bar)(成型机)顶业捧subzero深冷处理
three plate三极式模具
runner system浇道系统
stress crack应力电裂orientation定向
sprue gate射料浇口,直浇口nozzle射嘴
sprue lock pin料头钩销(拉料杆) slag well冷料井
side gate侧浇口
edge gate侧缘浇口
tab gate搭接浇口
film gate薄膜浇口
flash gate闸门浇口
slit gate缝隙浇口
fan gate扇形浇口
dish gate因盘形浇口diaphragm gate隔膜浇口
ring gate环形浇口
subarine gate潜入式浇口tunnel gate隧道式浇口
pin gate针点浇口
Runner less无浇道
(sprue less)无射料管方式
long nozzle延长喷嘴方式sprue浇口;溶渣
各种模具常用成形方式
accurate die casting 精密压铸
powder forming 粉末成形
calendaring molding 压延成形
powder metal forging 粉末锻造
cold chamber die casting 冷式压铸
precision forging 精密锻造
cold forging 冷锻
press forging 冲锻
compacting molding 粉末压出成形
rocking die forging 摇动锻造
compound molding 复合成形
rotary forging 回转锻造
compression molding 压缩成形
rotational molding 离心成形
dip mold 浸渍成形
rubber molding 橡胶成形
encapsulation molding 注入成形
sand mold casting 砂模铸造
extrusion molding 挤出成形
shell casting 壳模铸造
foam forming 泡沫成形
sinter forging 烧结锻造
forging roll 轧锻
six sides forging 六面锻造
gravity casting 重力铸造
slush molding 凝塑成形
hollow(blow) molding 中空(吹出)成形squeeze casting 高压铸造
hot chamber die casting 热室压铸
swaging 挤锻
hot forging 热锻
transfer molding 转送成形
injection molding 射出成形
warm forging 温锻
investment casting 精密铸造
matched die method 对模成形法
laminating method 被覆淋膜成形
low pressure casting 低压铸造
lost wax casting 脱蜡铸造
matched mould thermal forming 对模热成形模
各式模具分类用语
bismuth mold 铋铸模
landed plunger mold 有肩柱塞式模具burnishing die 挤光模
landed positive mold 有肩全压式模具button die 镶入式圆形凹模
loading shoe mold 料套式模具center-gated mold 中心浇口式模具loose detail mold 活零件模具
chill mold 冷硬用铸模
loose mold 活动式模具
clod hobbing 冷挤压制模
louvering die 百叶窗冲切模composite dies 复合模具
manifold die 分歧管模具
counter punch 反凸模
modular mold 组合式模具
double stack mold 双层模具
multi-cavity mold 多模穴模具electroformed mold 电铸成形模multi-gate mold 复式浇口模具expander die 扩径模
offswt bending die 双折冷弯模具extrusion die 挤出模
palletizing die 叠层模
family mold 反套制品模具
plaster mold 石膏模
blank through dies 漏件式落料模porous mold 通气性模具duplicated cavity plate 复板模positive mold 全压式模具
fantail die 扇尾形模具
pressure die 压紧模
fishtail die 鱼尾形模具
profile die 轮廓模
flash mold 溢料式模具progressive die 顺序模
gypsum mold 石膏铸模
protable mold 手提式模具
hot-runner mold 热流道模具prototype mold 雏形试验模具
ingot mold 钢锭模
punching die 落料模
lancing die 切口模
raising(embossing) 压花起伏成形
re-entrant mold 倒角式模具sectional die 拼合模
runless injection mold 无流道冷料模具sectional die 对合模具
segment mold 组合模
semi-positive mold 半全压式模具shaper 定型模套
single cavity mold 单腔模具
solid forging die 整体锻模
split forging die 拼合锻模
split mold 双并式模具
sprueless mold 无注道残料模具squeezing die 挤压模
stretch form die 拉伸成形模sweeping mold 平刮铸模
swing die 振动模具
three plates mold 三片式模具trimming die 切边模
unit mold 单元式模具
universal mold 通用模具unscrewing mold 退扣式模具
yoke type die 轭型模
模具厂常用之标准零配件
air vent vale 通气阀
anchor pin 锚梢
angular pin 角梢
baffle 调节阻板
angular pin 倾斜梢
baffle plate 折流档板
ball button 球塞套
ball plunger 定位球塞
ball slider 球塞滑块
binder plate 压板
blank holder 防皱压板
blanking die 落料冲头
bolster 上下模板
bottom board 浇注底板
bolster 垫板
bottom plate 下固定板
bracket 托架
bumper block 缓冲块
buster 堵口
casting ladle 浇注包
casting lug
铸耳cavity 模穴(模仁)
cavity retainer plate 模穴托板center pin 中心梢
clamping block 锁定块
coil spring 螺旋弹簧
cold punched nut 冷冲螺母cooling spiral 螺旋冷却栓
core 心型
core pin 心型梢
cotter 开口梢
cross 十字接头
cushion pin 缓冲梢
diaphragm gate 盘形浇口
die approach 模头料道
die bed 型底
die block 块形模体
die body 铸模座
die bush 合模衬套
die button 冲模母模
die clamper 夹模器
die fastener 模具固定用零件
die holder 母模固定板
die lip 模唇
die plate 冲模板
die set 冲压模座
direct gate 直接浇口
dog chuck 爪牙夹头
dowel 定位梢
dowel hole 导套孔
dowel pin 合模梢
dozzle 辅助浇口
dowel pin 定位梢
draft 拔模锥度
draw bead 张力调整杆
drive bearing 传动轴承
ejection pad 顶出衬垫
ejector 脱模器
ejector guide pin 顶出导梢ejector leader busher 顶出导梢衬套ejector pad 顶出垫
ejector pin 顶出梢
ejector plate 顶出板
ejector rod 顶出杆
ejector sleeve 顶出衬套
ejector valve 顶出阀
eye bolt 环首螺栓
filling core 椿入蕊
film gate 薄膜形浇口
finger pin 指形梢
finish machined plate 角形模板finish machined round plate 圆形模板fixed bolster plate 固定侧模板flanged pin 带凸缘销
flash gate 毛边形浇口
flask 上箱
floating punch 浮动冲头
gate 浇口
gate land 浇口面
gib 凹形拉紧楔
goose neck 鹅颈管
guide bushing 引导衬套
guide pin 导梢
guide post 引导柱
guide plate 导板
guide rail 导轨
head punch 顶头冲孔
headless punch 直柄冲头
heavily tapered solid 整体模蕊盒hose nippler 管接头
impact damper 缓冲器
injection ram 压射柱塞
inlay busher 嵌入衬套
inner plunger 内柱塞
inner punch 内冲头
insert 嵌件
insert pin 嵌件梢
king pin 转向梢
king pin bush 主梢衬套
knockout bar 脱模杵
land 合模平坦面
land area 合模面
leader busher 导梢衬套
lifting pin 起模顶销
lining 内衬
locating center punch 定位中心冲头locating pilot pin 定位导梢
locating ring 定位环
lock block 压块
locking block 定位块
locking plate 定位板
loose bush 活动衬套
making die 打印冲子
manifold block 歧管档块master plate 靠模样板
match plate 分型板
mold base 塑胶模座
mold clamp 铸模紧固夹
mold platen 模用板
moving bolster 换模保持装置moving bolster plate 可动侧模板one piece casting 整体铸件parallel block 平行垫块
paring line 分模线
parting lock set 合模定位器pass guide 穴型导板
peened head punch 镶入式冲头pilot pin 导销
pin gate 针尖浇口
plate 衬板
pre extrusion punch 顶挤冲头punch 冲头
puncher 推杆
pusher pin 衬套梢
rack 机架
rapping rod 起模杆
re-entrant mold 凹入模retainer pin 嵌件梢
retainer plate 托料板
return pin 回位梢
riding stripper 浮动脱模器
ring gate 环型浇口
roller 滚筒
runner 流道
runner ejector set 流道顶出器runner lock pin 流道拉梢screw plug 头塞
set screw 固定螺丝
shedder 脱模装置
shim 分隔片
shoe 模座之上下模板
shoot 流道
shoulder bolt 肩部螺丝
skeleton 骨架
slag riser 冒渣口
slide(slide core) 滑块
slip joint 滑配接头
spacer block 间隔块
spacer ring 间隔环spider 模蕊支架spindle 主轴
sprue 注道
sprue bushing 注道衬套
sprue bushing guide 注道导套sprue lock bushing 注道定位衬套sprue puller 注道拉料
spue line 合模线
square key 方键
square nut 方螺帽
square thread 方螺纹
stop collar 限位套
stop pin 止动梢
stop ring 止动环
stopper 定位停止梢
straight pin 圆柱销
stripper bolt 脱料螺栓
stripper bushing 脱模衬套
stripper plate 剥料板
stroke end block 行程止梢submarine gate 潜入式浇口support pillar 支撑支柱/顶出支柱support pin 支撑梢
supporting plate 托板
sweep templete 造模刮板
tab gate 辅助浇口
taper key 推拔键
taper pin 拔锥梢/锥形梢
teeming 浇注
three start screw 三条螺纹
thrust pin 推力销
tie bar 拉杵
tunnel gate 隧道形浇口
vent 通气孔
wortle plate 拉丝模板
模具常用之工作机械
3D coordinate measurement 三次元量床
boring machine 搪孔机
cnc milling machine CNC铣床
contouring machine 轮廓锯床
copy grinding machine 仿形磨床
copy lathe 仿形车床
copy milling machine 仿形铣床
copy shaping machine 仿形刨床
cylindrical grinding machine 外圆磨床
die spotting machine 合模机
drilling machine 冲孔机
engraving machine 雕刻机
engraving E.D.M. 雕模放置加工机
form grinding machine 成形磨床
graphite machine 石墨加工机
horizontal boring machine 卧式搪孔机horizontal machine center 卧式加工制造中心internal cylindrical machine 内圆磨床
jig boring machine 冶具搪孔机
jig grinding machine 冶具磨床
lap machine 研磨机
machine center 加工制造中心
multi model miller 靠磨铣床
NC drilling machine NC钻床
NC grinding machine NC磨床NC lathe NC车床NC programming system NC程式制作系统planer 龙门刨床
profile grinding machine 投影磨床
projection grinder 投影磨床
radial drilling machine 旋臂钻床
shaper 牛头刨床
surface grinder 平面磨床
try machine 试模机
turret lathe 转塔车床
universal tool grinding machine 万能工具磨床vertical machine center 立式加工制造中心
wire E.D.M. 线割放电加工机
模具钢材
alloy tool steel 合金工具钢
aluminium alloy 铝合金钢
bearing alloy 轴承合金
blister steel 浸碳钢
bonderized steel sheet 邦德防蚀钢板carbon tool steel 碳素工具钢
clad sheet 被覆板
clod work die steel 冷锻模用钢
emery 金钢砂
ferrostatic pressure 钢铁水静压力forging die steel 锻造模用钢galvanized steel sheet 镀锌铁板
hard alloy steel 超硬合金钢
high speed tool steel 高速度工具钢
hot work die steel 热锻模用钢
low alloy tool steel 特殊工具钢
low manganese casting steel 低锰铸钢marging steel 马式体高强度热处理钢martrix alloy 马特里斯合金
meehanite cast iron 米汉纳铸钢meehanite metal 米汉纳铁
merchant iron 市售钢材
molybdenum high speed steel 钼系高速钢molybdenum steel 钼钢
nickel chromium steel 镍铬钢prehardened steel 顶硬钢
silicon steel sheet 矽钢板
stainless steel 不锈钢
tin plated steel sheet 镀锡铁板
tough pitch copper 韧铜
troostite 吐粒散铁
tungsten steel 钨钢
vinyl tapped steel sheet 塑胶覆面钢板
表面处理关连用语
age hardening 时效硬化
ageing 老化处理
air hardening 气体硬化
air patenting 空气韧化
annealing 退火
anode effect 阳极效应
anodizing 阳极氧化处理
atomloy treatment 阿托木洛伊表面austempering 奥氏体等温淬火austenite 奥斯田体/奥氏体
bainite 贝氏体
banded structure 条纹状组织
barrel plating 滚镀
barrel tumbling 滚筒打光blackening 染黑法
blue shortness 青熟脆性bonderizing 磷酸盐皮膜处理
box annealing 箱型退火
box carburizing 封箱渗碳
bright electroplating 辉面电镀bright heat treatment 光辉热处理bypass heat treatment 旁路热处理carbide 炭化物
carburized case depth 浸碳硬化深层carburizing 渗碳
cementite 炭化铁
chemical plating 化学电镀chemical vapor deposition 化学蒸镀coarsening 结晶粒粗大化
coating 涂布被覆
cold shortness 低温脆性comemtite 渗碳体
controlled atmosphere 大气热处理corner effect 锐角效应
creeping discharge 蠕缓放电decarburization 脱碳处理decarburizing 脱碳退火
depth of hardening 硬化深层diffusion 扩散
diffusion annealing 扩散退火electrolytic hardening 电解淬火embossing 压花
etching 表面蚀刻
ferrite 肥粒铁
first stage annealing 第一段退火flame hardening 火焰硬化
flame treatment 火焰处理
full annealing 完全退火
gaseous cyaniding 气体氧化法globular cementite 球状炭化铁grain size 结晶粒度
granolite treatment 磷酸溶液热处理graphitizing 石墨退火hardenability 硬化性hardenability curve 硬化性曲线hardening 硬化
heat treatment 热处理
hot bath quenching 热浴淬火
hot dipping 热浸镀
induction hardening 高周波硬化ion carbonitriding 离子渗碳氮化ion carburizing 离子渗碳处理
ion plating 离子电镀
isothermal annealing 等温退火liquid honing 液体喷砂法
low temperature annealing 低温退火malleablizing 可锻化退火martempering 麻回火处理martensite 马氏体/硬化铁炭metallikon 金属喷镀法metallizing 真空涂膜
nitriding 氮化处理nitrocarburizing 软氮化normalizing 正常化
oil quenching 油淬化
overageing 过老化
overheating 过热
pearlite 针尖组织
phosphating 磷酸盐皮膜处理physical vapor deposition 物理蒸镀plasma nitriding 离子氮化
pre-annealing 预备退火precipitation 析出
precipitation hardening 析出硬化press quenching 加压硬化process annealing 制程退火quench ageing 淬火老化
quench hardening 淬火quenching crack 淬火裂痕quenching distortion 淬火变形quenching stress 淬火应力
模具专业英文术语大全
模具英语专业术语 模具述语 一、入水:gate 进入位: gate location 水口形式:gate type 大水口:edge gate 细水口: pin-point gate 水口大小:gate size 转水口: switching runner/gate 唧嘴口径: sprue diameter 二、流道: runner 热流道: hot runner,hot manifold 热嘴冷流道: hot sprue/cold runner 唧嘴直流: direct sprue gate 圆形流道:round(full/half runner 流道电脑分析:mold flow analysis 流道平衡:runner balance 热嘴: hot sprue 热流道板:hot manifold 发热管:cartridge heater 探针: thermocouples 插头: connector plug 插座: connector socket 密封/封料: seal 三、运水:water line 喉塞:line lpug 喉管:tube 塑胶管:plastic tube 快速接头:jiffy quick connector plug/socker 四、模具零件: mold components 三板模:3-plate mold 二板模:2-plate mold 边钉/导边:leader pin/guide pin 边司/导套:bushing/guide bushing 中托司:shoulder guide bushing 中托边L:guide pin 顶针板:ejector retainner plate 托板: support plate 螺丝: screw 管钉:dowel pin 开模槽:ply bar scot 内模管位:core/cavity inter-lock 顶针: ejector pin 司筒:ejector sleeve 司筒针:ejector pin 推板:stripper plate 缩呵:movable core,return core core puller 扣机(尼龙拉勾):nylon latch lock 斜顶:lifter 模胚(架): mold base 上内模:cavity insert 下内模:core insert 行位(滑块): slide 镶件:insert 压座/斜鸡:wedge 耐磨板/油板:wedge wear plate 压条:plate 撑头: support pillar 唧嘴: sprue bushing 挡板:stop plate 定位圈:locating ring 锁扣:latch 扣鸡:parting lock set 推杆:push bar 栓打螺丝:S.H.S.B 顶板:eracuretun 活动臂:lever arm 分流锥:spure sperader 水口司:bush 垃圾钉:stop pin 隔片:buffle 弹弓柱:spring rod 弹弓:die spring 中托司:ejector guide bush 中托边:ejector guide pin 镶针:pin 销子:dowel pin 波子弹弓:ball catch 喉塞: pipe plug
模具专业术语 英语对照
GLOSSARY A abrasive grinding 强力磨削 L3 abrasive[E'breisiv] a.磨料的, 研磨的 L2,3 absence ['AbsEns] n.. 不在,缺席 L17 accesssory[Ak'sesEri] n.附件 L10 accommodate[E'kCmEdeit] v. 适应 L5 accordingly[E'kC:diNli] adv.因此,从而,相应地 L7,13 accuracy['AkjurEsi] n精度,准确性 L1,3 actuate['Aktjueit] vt.开动(机器), 驱动 L8 adequate['Adikwit] a. 足够的 L13 adhesive[Ed'hi:siv] n. 粘合剂 L22 adjacent[E'dVeisnt] a. 邻近的 L13 adopt[E'dCpt] vt. 采用 L4 advance [Ed'vA:ns] n.进步 L7 advisable [Ed'vaizbl] adj. 可取的 L20 agitate['AdViteit] v. 摇动 L2 a large extent 很大程度 L4,13 algorithm ['Al^EriTEm] n. 算法 L6 align [E'lain] v 定位,调准 L17 alignment[E'lainmEnt] n. 校直 L11 all-too-frequent 频繁 L17 allowance[E'lEuens] n. 容差, 余量 L5 alternate['C:ltEnit]v.交替,轮流 L1 alternative[C:l'tE:nEtiv] n. 替换物 L3 alternatively[C:l'tE:nEtivli] ad. 做为选择, 也许 L5 aluminiun[7Alju'minjEm] n.铝 L2 ample['Ampl] adj. 充足的 L20 analysis [E'nAlEsis] n. 分析 L6 ancillary['AnsilEri] a.补助的, 副的 L4 angular ['A^julE] adj. 有角的 L20 annealing[E'li:liN] n.退火 L2 aperture ['ApEtFE] n.孔 L17 applied loads 作用力 L1 appropriate [E'prEuprieit] a. 适当的 L6,20 arc[a:k] n.弧, 弓形 L10 arise[E'raiz] vi. 出现, 发生 L21 arrange[E'reidV] v. 安排 L12 article['a:tikl] n.制品, 产品 L21 ascertain[7AsE'tein] vt. 确定, 查明 L1 assemble[E'sembl] vt.组装 L4 attitude ['Atitju:d] n 态度 L17 auxiliary [C:^'ziljEri]adj. 辅助的 L8 avoid[E'vCid] v.避免 L7 axis['Aksis] n.轴 L5 axle['Aksl] n.轮轴, 车轴 L1 B backup['bAk7Qp] n. 备份 L9 batch [bAtF] n 一批 L17 bearing['bZEriN] n.轴承,支座 L21 bed[bed] n. 床身 L5 behavior[bi'heivjE] n. 性能 L1 bench-work 钳工工作 L4 bend[bend] v.弯曲 L1 beneath[bi'ni:W] prep在···下 L4 bin [bin] n. 仓,料架 L19 blank [blANk] n. 坯料 L20 blank [blANk] v. 冲裁,落料 L17 blanking tool 落料模 L17 blast [blQst] n.一阵(风) L18 blemish['blemiF] n. 缺点, 污点 L13 bolster['bEulstE] n. 模座,垫板 L4,5 boost[bu:st] n. 推进 L9 boring['bC:riN] n.镗削, 镗孔 L4,5 bracket ['brAkit] n. 支架 L19 brass [brAs] n.黄铜 L2 break down 破坏 L1 breakage ['breikidV] n.破坏 L17 bridge piece L16 brine[brain] n. 盐水 L2 brittle['britl] adv.易碎的 L1 buffer [bQfE] n.缓冲器 L8 built-in 内装的 L9 bulging [bQldViN] n. 凸肚 L22 burr [bE:] n. 毛刺 L17 bush [buF] n. 衬套 L17 bush[buF]n. 衬套 L5 by far (修饰比较级, 最高级)···得 多, 最 L3 by means of 借助于 L5 C cabinet ['kAbinit] n.橱柜 L7 call upon 要求 L17 carbide['ka:baid] n.碳化物 L10 carburzing['ka:bjuretiN] n. 渗碳 L2 carriage['kAridV] n.拖板, 大拖板 L5 carry along 一起带走 L18 carry down over 从···上取下 L21 carry out 完成 L17 case hardening 表面硬化 L2 case[keis] n. 壳, 套 L2 cast steel 铸钢 L17 casting['ka:stiN] n. 铸造,铸件 L3 category['kAtE^Euri] n. 种类 L6,15 caution ['kC:FEn] n. 警告,警示 L17 cavity and core plates 凹模和凸模板 L11 cavity['kAviti] n.型腔, 腔, 洞 L4,10 centre-drilling 中心孔 L5 ceramic[si'rAmik] n.陶瓷制品 L3 chain doted line 点划线 L11 channel['tFAnl] n.通道, 信道 L8 characteristic[kArEktE'ristik] n.特性 L1 check[tFek] v.核算 L21 chip[tFip] n.切屑, 铁屑 L3
模具专业英语词汇大全
模具专业英语词汇 A abrasion n. 磨损 abrasion resistance n. 耐磨损性 abrasive n. 磨料 accelerator n. 促进剂 accuracy n. 准确性 accurate die casting 精密压铸 air trap 积风 acrylic n. 丙烯酸 /压克力 ì active plate 活动板 additive n. 添加剂 adhere v. 黏附 adhesion n. 黏合 adhesive n. 胶粘剂 air-cushion eject-rod 气垫顶杆 air cushion plate 气垫板 air entrapment n. 困气 anneal v. 退火 assemble v. 总成 B back pressure 背压 bismuth mold 铋铸模 baffle plate 挡块 barrel n. 机筒 /料筒 / bending block 折刀 bottom block 下垫脚 bottom plate 下托板(底板) bushing bolck 衬套 barrel temperature 料筒温度 blush 发 blank through dies 漏件式落料模 burnishi blow molding n. 吹塑成型 blow molding machine n. 吹塑机 brittle adj. 脆性 bubble n. 气泡 burr 毛刺 button d by-product n. 副产品 C calendering n. 压延 carbon steel n. 碳素钢 casting n. 铸造 catalyst n. 催化剂 cavity n. 型腔 chemical resistance n. 耐化学腐蚀性 chip v. 削 /凿
模具专业英语词汇
入水:gate 进入位:gate location 水口形式:gate type 大水口:edge gate 细水口: pin-point gate 水口大小:gate size 转水口:switching runner/gate 唧嘴口径:spray diameter 流道: runner 热流道:hot runner, hot manifold 热嘴冷流道: hot spray/cold runner 唧嘴直流: direct spray gate 圆形流道:round(full/half runner 流道电脑分析:mold flow analysis 流道平衡:runner balance 热嘴:hot spray 热流道板:hot manifold 发热管:cartridge heater 探针: thermocouples 插头:connector plug 插座: connector socket 密封/封料: seal 运水:water line 喉塞:line plug 喉管:tube 塑胶管:plastic tube 快速接头:jiffy quick connector plug 模具零件:mold components 三板模:3-plate mold 二板模:2-plate mold 边钉/导边:leader pin/guide pin 边司/导套:bushing/guide bushing 中托司:shoulder guide bushing 中托边L:guide pin 顶针板:ejector retainner plate 托板:support plate 螺丝: screw 管钉:dowel pin 开模槽:ply bar slot 内模管位:core/cavity inter-lock 顶针:ejector pin 司筒:ejector sleeve 司筒针:ejector pin 模具专业英语 推板:stripper plate 缩呵:movable core, return core puller 扣机(尼龙拉勾):nylon latch lock 斜顶:lifter 模胚(架): mold base 上内模:cavity insert 下内模:core insert 行位(滑块): slide 镶件:insert 压座/斜楔:wedge 耐磨板/油板:wedge wear plate 压条:plate 撑头: support pillar 唧嘴: sprue bushing 挡板:stop plate 定位圈:locating ring 锁扣:latch 扣鸡:parting lock set 推杆:push bar 栓打螺丝:S.H.S.B injection nozzle 射出喷嘴 顶板:eracuretun 活动臂:lever arm 分流锥:spure sperader 水口司:bush 垃圾钉:stop pin 隔片:buffle 弹弓柱:spring rod 弹弓:die spring 中托司:ejector guide bush 中托边:ejector guide pin 镶针:pin 销子:dowel pin 波子弹弓:ball catch 喉塞: pipe plug 锁模块:lock plate 斜顶:angle from pin 斜顶杆:angle ejector rod 尼龙拉勾:parting locks 活动臂:lever arm 复位键、提前回杆:early return bar 气阀:valves 斜导边:angle pin
模具常用术语中英文对照
模芯 Parting Core 耐落胶 Teflon Paste 局部视图 Partial View 偏移量 Offset 冷料 Cold Slag 水塞 Water Line Plug 线切割 Wire 撬模脚 Ppy Slot 轮廓 Contour 重新加工 Reworked 螺纹孔Tapping Hole 配件 Components 连接件 Fittings 补偿 Compensation 斜针 Angle Pin 平面度 Parallel 接合 Engage 倒角Chamfer 替换镶件Interchangeable Mold Inserts 模胚 Mold Base 指定吨位的注塑机 Specific Press 热嘴Hotnozzle 水嘴接头 Water Fitting 火花机 Edm 螺纹 Eyebolt Thread 熔接线 Weildline 回针 Stop Pin 压机 Press 二级顶出针 Sub-Leaderd Pin 嗮纹 Texturing 镶件 Mold Insert 梯形 Trapezoid
加硬 Harden 凸缘、法兰 Flange 唧嘴 Sprue 方铁 Spacer Block 设计筒图 Design Preliminary 顶针板 Ejector Plate 名称块表 Title Block 顶针底板 Ejector Retainer Plate 版本标识 Revision Level 垫板 Retainer Plate 材料清单 Stock List 后模镶针 Core Pin 制模 Build Mold 垃圾钉 Stop Pin 手动滑块 Hand Slide 有托顶针 Shoulder Ejector Pin 漏水测试 Leak Test 顶针板导套Guided Ejection Bushing 流道排气 Runner Vents 针板导柱 Guided Ejection Leader Pin 抛光 Draw Polish 唧嘴 Sprue Bushing 侧抽芯 Slide Action 三板模延伸式唧嘴 Extension Noozzle Bulishing 加强筋 Reinforcing 水口板导套 Runner Stripper Pin 三角撑 Gusset 定位圈(法兰)Locating Ring 柱子 Bossed 管钉(定位销)Dowel Pin 出模斜度 Draft 管状管钉 Tubular Dowel
模具专业的英语词汇大全
模具专业的英语词汇大全 一、模具专业英语 入水:gate 进入位:gate location 水口形式:gate type 大水口:edge gate 细水口: pin-point gate 水口大小:gate size 转水口:switching runner/gate 唧嘴口径:sprue diameter 二、流道: runner 热流道:hot runner,hot manifold 热嘴冷流道: hot sprue/cold runner 唧嘴直流: direct sprue gate 圆形流道:round(full/half runner 流道电脑分析:mold flow analysis 流道平衡:runner balance 热嘴:hot sprue 热流道板:hot manifold 发热管:cartridge heater 探针: thermocouples 插头:connector plug 插座: connector socket 密封/封料: seal 三、运水:water line 喉塞:line lpug 喉管:tube 塑胶管:plastic tube 快速接头:jiffy quick connector plug/socker 四、模具零件:mold components 三板模:3-plate mold 二板模:2-plate mold 边钉/导边:leader pin/guide pin 边司/导套:bushing/guide bushing 中托司:shoulder guide bushing 中托边L:guide pin 顶针板:ejector retainner plate 托板:support plate 螺丝: screw 管钉:dowel pin 开模槽:ply bar scot 内模管位:core/cavity inter-lock
模具英语术语
A abrasive grinding 强力磨削abrasive[?'breisiv] a.磨料的, 研磨的 absence ['?bs?ns] n.不在,缺席accesssory[?k'ses?ri] n.附件accommodate[?'k m?deit] v. 适应 accordingly[?'k :di?li] adv.因此,从而,相应地accuracy['?kjur?si] n精度,准确性 actuate['?ktjueit] vt.开动(机器), 驱动adequate['?dikwit] a. 足够的adhesive[?d'hi:siv] n. 粘合剂adjacent[?'d?eisnt] a. 邻近的adopt[?'d pt] vt. 采用advance [?d'v?:ns] n.进步advisable [?d'vaizbl] adj. 可取的 agitate['?d?iteit] v. 摇动 a large extent 很大程度algorithm ['?l??ri??m] n. 算法 align [?'lain] v 定位,调准alignment[?'lainm?nt] n. 校直 all-too-frequent 频繁allowance[?'l?uens] n. 容差, 余量 alternate[' :lt?nit] v.交替,轮流 alternative[ :l't?:n?tiv] n. 替换物 alternatively[ :l't?:n?tivli] ad. 做为选择, 也许aluminiun[ ?lju'minj?m] n.铝 ample['?mpl] adj. 充足的analysis [?'n?l?sis] n. 分析ancillary['?nsil?ri] a.补助的, 副的 angular ['??jul?] adj. 有角的annealing[?'li:li?] n.退火 aperture ['?p?t??] n.孔 applied loads 作用力 appropriate [?'pr?uprieit] a. 适当的 arc[a:k] n.弧, 弓形 arise[?'raiz] vi. 出现, 发生 arrange[?'reid?] v. 安排 article['a:tikl] n.制品, 产品 ascertain[ ?s?'tein] vt. 确定, 查明 assemble[?'sembl] vt.组装 attitude ['?titju:d] n 态度 auxiliary [ :?'zilj?ri] adj. 辅助的 avoid[?'v id] v.避免 axis['?ksis] n.轴 axle['?ksl] n.轮轴, 车轴 B backup['b?k ?p] n. 备份 batch [b?t?] n 一批 bearing['b??ri?] n.轴承,支座 bed[bed] n. 床身 behavior[bi'heivj?] n. 性能 bench-work 钳工工作 bend[bend] v. 弯曲 beneath[bi'ni: ] prep在··· bin [bin] n. 仓,料架 blank [bl??k] n. 坯料 blank [bl??k] v. 冲裁,落料 blanking tool 落料模 blast [bl?st] n.一阵(风) blemish['blemi?] n. 缺点, 污点 bolster['b?ulst?] n. 模座,垫 板 boost[bu:st] n. 推进 boring['b :ri?] n.镗削, 镗孔 bracket ['br?kit] n. 支架 brass [br?s] n.黄铜 break down 破坏 breakage ['breikid?] n.破坏 bridge piece brine[brain] n. 盐水 brittle['britl] adv.易碎的 buffer [b?f?] n.缓冲器 built-in 内装的 bulging [b?ld?i?] n. 凸肚 burr [b?:] n. 毛刺 bush [bu?] n. 衬套 bush[bu?] n. 衬套 by far (修饰比较级, 最高 级)···得多, 最 by means of 借助于 C cabinet ['k?binit] n.橱柜 call upon 要求 carbide['ka:baid] n.碳化物 carburzing['ka:bjureti?] n. 渗碳 carriage['k?rid?] n.拖板, 大拖板 carry along 一起带走 carry down over 从···上取 carry out 完成 case hardening 表面硬化 case[keis] n. 壳, 套 cast steel 铸钢 casting['ka:sti?] n. 铸造,铸件 category['k?t???uri] n. 种 类 caution ['k :??n] n. 警告,警示 cavity and core plates 凹模和凸模板 cavity['k?viti] n.型腔, 腔, 洞 centre-drilling 中心孔 ceramic[si'r?mik] n.陶瓷制品 chain doted line 点划线 channel['t??nl] n.通道, 信道 characteristic[k?r?kt?'ristik] n.特性 check[t?ek] v.核算 chip[t?ip] n.切屑, 铁屑
模具常用英文词汇
钣金设计中常用的其它术语 扩孔enlarge hole 自铆self-chinching 全周压毛边all round burr 平头拉钉set-head rivet 表面处理finish 定位销dowel pin 挂钩hook 平头铆钉closed-end rivet 焊接线weld line 塑料固定栓fastener, plastic, push-type 压合胶粘剂pressure sensitive adhesive 尼龙绑带tie wrap, nylon 五金件hardware 泡棉静电导片gasket, foam, emi 贴纸labeling 铍铜静电导片gasket, beck, emi 烤漆paint 圆头螺钉button-head screw 电镀plating 平头螺母nut flush 铭板nameplate 平齐自铆flush, self-clinching 包装packing 紧固螺丝fix screw 铁材零件sheet metal parts 组装assembly 塑料零件plastic parts 凹陷,顶针sink mark 压边铆钉open-end rivet 插孔jack 弹簧螺丝caps 度thick 文字,记号char actor 半冲孔spring slice 角corner 基座chassis 自锁螺母nut self-clenching 承座bracket 轴肘式铆接toggle lock 承架horsing 卡尺caliper 下盖base 打印字模stamp letter 去毛边deburr 推板导住ejector guide 直导套guide bush, straight[straight bushing] 带头导套guide bush, straight {shoulder bushing} 推板导套ejector guide bush[ejector bushing] 定位圈Locating ring 锥形定位件mould bases locating elements 复位杆ejector plate return pin[push-back pin] 限位钉stop pin[stop but ton] 限位块stop block [stop pad] 定距拉杆puller[length]bolt 定距拉板puller[limit]plate 成形推杆forming ejector pin 圆柱头推杆ejector pin with cylindrical head 带肩推杆shouldered ejector pin 扁推杆flat ejector pin 推管ejector sleeve 推块ejector pad 推件板stripper plate 推杆固定板ejector retainer plate ; 推板ejection plate[elector plate] 连接推杆ejector tie rod 冲裁间隙blanking clearance 模具闭合高度die shut height 压力机闭合高度shut height Of press machine 冲模寿命die life 压力中心center Of load 冲模中心center Of die 冲压方向pressing direction 送料方向feed direction 排样blank layout 搭边scrap 进距feed pitch 切边余量trimming allowance 毛刺burr 冲裁力blanking force 弯曲力bending force 拉仲力drawing force 挤压力extruding force 卸料力stripping force 推件力ejecting force 顶件力kicking force 压料力pressure plate force 压边力black holder force 毛坯blank ;
模具术语(中英文对照)
AD-Diameter The tread diameter at the centerline of the tread (EU); also: "T-Diameter"(GT) AD直径:指胎面中心线直径(EU)。又叫T直径(GT) Auto-lock Ear A Lug on the cone ring used to mount the mold/container in the top half of a 60“ NRM Auto-lock press. 导环上的突缘,用于和60“ NRM Auto-lock 硫化机上半部连接。 Bead Ring The tire bead forming ring (also: toe ring) 钢圈,也称toe ring Bead Ring Register The landing and tapered seat that the bead ring fits into 钢圈配合:侧板上,和钢圈配合的平面及锥面 Bottom Container Plate The plate that the bottom sidewall plate is bolted to 模壳底座 Bottom Container Plate Lifting Lug A lug attached to the Bottom Container Plate with Horizontal holes used for lifting. 模壳底座吊耳:装配在底座上、有水平的孔,用来吊装的吊耳 Bottom Container Plate Dowel Pin Lug A lug attached to the Bottom Container Plate that supports the Dowel Pin Bushing. 装配在底座上,用来支承定位销套的突缘 Bottom Container Plate Hold Down A lug that is used to fix the Bottom Plate in the Press. 用来将底座装配在硫化机上的突缘 Breaker Hook A hook fixed to the bottom of the tread segment that catches the bottom container plate only when the segment will not release from the tire during de-molding. 分离钩:固定在花纹块底部的钩子,轮胎硫化完后若花纹块不能跟轮胎分离,就用此钩抓住模壳底座帮助花纹块和轮胎进行分离。 Breaker Hook Guide Piece A block bolted to the breaker hook that aligns the tread segment with a slot in the bottom container plate. 分离钩导块:用螺栓固定在Breaker Hook上,定位花纹块和模壳底座上槽的定位块。Bronze Wear Plates Any sacrificial metal plate placed under, over or behind a component to keep the components from wearing on each other (greasing) 青铜耐磨板(油润滑的)
模具专业英语词汇
Injection Mold Technical Terms (一)模具专业基本用词Professional Terms 塑料—plastic, resin 样件—sample 钢料—steel 注塑机—injection machine, press 产品—part, product, moulding 模具—mold, mould, tool A 简易模(样板模)—prototype mold B 量产用模具—production mold 三维造型(数模)—3D model, 3D data 二维产品图—2D part drawing 设计—design 制造—manufacture, build up, construction 检验—check, inspection 测量—measure, inspection 修改—change, modify, correction 工程更改—engineer change 质量—quality 数量—quantity 基准—datum, reference 牛角入水-rads gate (二)如何解析2D 产品图How to read 2D part drawing 产品几何Geometry 1.点—point 2.线(边)—line, edge 3.面face A 侧面—side B 表面—surface C 外观面—appearance surface 4.壁厚—wall thickness, stock thickness 5.加强筋(骨位)—rib 6.孔—hole 7.细长的槽—slot 8.柱位—boss 9.角—corner A 圆角—fillet B 倒角—chamfer C 尖角—sharp corner 10.斜度—angle, taper 11. 凹槽—recess , groove 分模信息Splitting 分型线—parting line (P/L), splitting line 主分模方向—main direction, line of draw 浇口设定—gating 产品标识Part Identification 产品名称—part name (P/N) 产品编号+版本号—part number + revision (Rev.)
模具专业英语词汇.doc
模具专业英语词汇 landed plunger mold 有肩柱塞式模具burnishing die 挤光模英语站landed positive mold 有肩全压式模具button die 镶入式圆形凹模 loading shoe mold 料套式模具center-gated mold 中心浇口式模具loose detail mold 活零件模具 chill mold 冷硬用铸模 loose mold 活动式模具 clod hobbing 冷挤压制模 louvering die 百叶窗冲切模composite dies 复合模具 manifold die 分歧管模具 counter punch 反凸模 modular mold 组合式模具 double stack mold 双层模具 multi-cavity mold 多模穴模具electroformed mold 电铸成形模multi-gate mold 复式浇口模具expander die 扩径模 offswt bending die 双折冷弯模具extrusion die 挤出模 palletizing die 叠层模 family mold 反套制品模具 plaster mold 石膏模 blank through dies 漏件式落料模porous mold 通气性模具 duplicated cavity plate 复板模positive mold 全压式模具 fantail die 扇尾形模具 pressure die 压紧模 fishtail die 鱼尾形模具 profile die 轮廓模 flash mold 溢料式模具 progressive die 顺序模 gypsum mold 石膏铸模 protable mold 手提式模具 hot-runner mold 热流道模具prototype mold 雏形试验模具 ingot mold 钢锭模 punching die 落料模
常用模具英语单词
die 模具 figure file, chart file图档 cutting die, blanking die冲裁模progressive die, follow (-on)die 连续模compound die复合模 punched hole冲孔 panel board镶块 to cutedges=side cut=side scrap切边 to bending折弯 to pull, to stretch拉伸 Line streching, line pulling线拉伸engraving, to engrave刻印 upsiding down edges翻边 to stake铆合 designing, to design设计 design modification设计变化 die block模块 folded block折弯块 sliding block滑块 location pin定位销 lifting pin顶料销 die plate, front board模板 padding block垫块 stepping bar垫条 upper die base上模座 lower die base下模座 upper supporting blank上承板 upper padding plate blank上垫板spare dies模具备品 bolt螺栓
模具述语 一、入水:gate 进入位:gate location 水口形式:gate type 大水口:edge gate 细水口:pin-point gate 水口大小:gate size 转水口:switching runner/gate 唧嘴口径:sprue diameter 二、流道: runner 热流道:hot runner, hot manifold 热嘴冷流道: hot sprue/cold runner 唧嘴直流: direct sprue gate 圆形流道:round(full/half runner 流道电脑分析:mold flow analysis 流道平衡:runner balance 热嘴:hot sprue 热流道板:hot manifold 发热管:cartridge heater 探针: thermocouples 插头:connector plug 插座:connector socket 密封/封料:seal 三、运水:water line 喉塞:line lpug 喉管:tube
模具英语专业术语
模具(MOULD/MOLD,TOOL): CAVITY:前模 CORE:后模(定模) DIMENSION:寸法 GATE:浇口/水口/入水口 PIN GATE:点水口/点浇入水 SIDE GATE:边水口/侧浇入水/大水口APPERANCE SURFACE:体裁面WARPAGE DIRECTION:变形方向 DRAFT ANGEL:脱模斜度 PARTING LINE/P。L:分模线 EJECT PIN/E。P:注塑顶针 BLAST/TEXTURE:喷啥,蚀纹 MIRROR FINISH:镜面(抛光)处理POLISH:抛光 EMD:放电加工 WELD:熔接加工(烧焊) LATHE:车床 MILLING CUTTER:铣刀 MILLING MACHINE:铣床 WIRE CUT:线切割 CNC:主加工中心 POWER DRILL:电钻 DRILLING:钻孔 FRITING:烧结 ANNEALING:淬火 注塑术语(INJECTION) SCREW:螺杆 WELD LINE:熔接线 SINK MARK:缩水 DRAG MARK:脱花 BURR:批锋 FLOW MARK:流纹 SHADOW MARK/GLOSS DIFFERENCE:光影SHORT:缺胶 INJECTION CYCLE:成型周期
注塑英语 型厚大小 Thick size 锁模结构(机绞/直压) Mode locking structure(machine twists/straight pressure) 最大开模距离 The biggest die sinking is away from 动模板最大模具重量 Moves the template maximum mold weight 哥林柱间距 Elder brother forest column spacing 顶出形式(电动五点,油压五点,油压十三点) Goes against the form (electrically operated five spots, flowing tubing head pressure five spots, flowing tubing head pressure 13 spots) 顶出长度 Goes against the length 顶棍孔直径 Goes against the stick hole diameter 顶棍孔中心矩 Goes against the stick hole central moment 螺杆材质(合金) Screw rod material quality (alloy) 螺杆转速 Screw rod rotational speed 最大射出体积 Projects the volume most greatly 最大射出量 Projects the quantity most greatly 射出率 Ejection rate 每10mm射出量(理论) Each 10mm projects the quantity (theory) 射咀直径 Shoots ju the diameter 射咀R值 Shoots ju the R value 射咀空径 Shoots ju the spatial diameter 定位环直径 Locating ring diameter 溶胶能力 Sol ability 驱动方式(全自动/全液压)