模具常用英语对话
模具常用英语对话
1．XXX！你现在有空吗，我可以问你一些问题吗？
Could I ask you some questions if you are free? / Are you free now? May I ask you some questions (a question)?
2．请问此产品的面是否为外观面？表面做什么处理？是晒纹/抛光？
Can you tell me whether the surface of this part is a visible/esthetic one? What will we do for its surface? Texture or Polishing ?
3．请问产品这个面可否加顶针或顶块？产品允许加扁顶针吗？
Does this part need an ejector pin or an ejector bar? Can we add an ejector blade?
4．这个产品的柱位我们打算做司筒。（或镶针）可以吗？
Can we add ejector sleeves or ejector pins in the boss of this part?
5．产品的这个位置不能出模，我们打算做行位，在此面上会有分模线，你接受吗？
There's an undercut at this position and it needs a slider. It will also have a parting line on this side, is that OK?
6．产品里面的这个位置我们打算做斜顶或内行位，有问题吗？
We will make the lifter and (inner) slider in this position, will that be a problem?
7．你提供的2D产品图与3D产品图不一致，请问以哪一个图面为准？
The 2D and 3D drawing you provided is not the same, can you tell me which one is
correct?
8．你提供的3D产品图有的地方没有出模角，有的地方胶位太厚，有的地方胶位太溥，这些产品问题我们可以自己修改吗？修改后会给交给你确认。
There is no draft angle in the 3D drawing, some materials are too thick, and some place are too thin. Can we modify this part by ourselves? We will send the drawing to you for you to check after we modify it.
9．按你们提供的缩水率千分之五，这个模具的尺寸已经做到了模具图面要求。但注塑出来的产品不符合你们的产品图。请确认你们的材料的缩水率是否正确？
According to the shrinkage one over two hundred, the mold has been done in the right dimension, but the part falls short to your part drawing, are you sure the shrinkage is
right?
10．产品的这个位置太小，导致模具钢料太溥，能够加宽这个位置吗？
This position is too small and will make the steel material here too thin, can we widen it here?
11．斜顶与后面的柱位空间太小，斜顶在运动时会干涉到柱子，能移动这个柱子的位置吗？
The angular lifter interferes with the boss during ejection. Please consider changing the position of the boss.
12．这个筋骨位胶厚太溥，而且高度偏高，注塑时很难填充这个筋位，可以增加这个筋骨位的厚度吗？
The rib here is too thin and on the high side, so it will be difficult to fill here when we do the injection, can you increase the thickness of this rib?
13．你是想将此筋骨位的高度加高/减低吗？加胶的位置我们将用铜公放电加深。
但减胶的位置有两种做法，1、做镶件；2、烧焊；因为镶件的底部有运水，我们简单的做法是烧焊处理，你可以接受吗？
Will you increase/decrease the material on this rib? We will use EDM if you add material, but there are two option if you choose to decrease: 1. Make inserts;2 Welding, because there is water in the bottom of the insert, is that OK?
14．这个样板的筋骨位底部烧焦，是因为排气不良，我们可以在筋骨位的中间增加一个镶件。
This sample has been burned in the bottom because the venting is not good, we can add an insert in the middle of the rib.
15．重做镶件大约需要5-6天时间，你能接受吗？
It will take about 5 or 6 days to redo the insert, is that OK?
16．产品的这个面我们已经做了晒纹处理，如果需要加胶，这个面我们需要重新外发晒纹。可能需要几天的时间。所以我们直接以铜公放电的火花纹取代你要求的纹路，你可以接受吗？
We have made the texture on this side, if we add material, it will take some days to
remake the texture by out-resourcing, so we suggest using the texture by EDM instead, is that OK?
17．模具是用公制/英制的配件？需要备用件吗？
Is this mold dimension measured in inches or meters? Does it need spare parts?
18．模具上铭牌上的刻字内容是由你们提供吗？你们什么时候可以这些刻字资料。
Will you provide the engraving content of the plate of this mold to us? When will you
send it?
19．可否提供此模具生产时，注塑机的型号及相关资料。如：啤机大小、呵林柱尺寸、顶棍孔尺寸等
Can you provide the type of injection machine and other related information of this mold to us? Such as the boss dimension, the hole's dimension of the ejector pin and the size of the injection machine and so on.
20．这个问题我需要同其它同事商议会再答复你。
I need to discuss this problem with the other colleagues and then I wil l reply back to you.
21．我们将尽力达成你的计划，如有异常，会及时通知你。
We will try our best to complete your plan, if there are any complications, we will notify you immediately.
22．这个产品的长度为330.12MM,宽度为78.96MM,高度为45MM.胶厚为2MM,重量为70.63g,试模注塑机型号为250吨,胶料颜色为黑色,产品外表面晒纹处理,内表面为抛光.需要日期章、环保章、材料章.前后模用2344氮硬，斜顶和行位座用738H，以上模具信息正确吗？请确认！
The length of this part is 330.12MM, Width is 78.96MM, height is 45MM, thickness is
2MM, weight is 70.63g, the injection machine is 250T, the material is black, the outside of the part has texture, inner side needs polishing, and it also needs a date and recycle
stamp ,the core & cavity is 2344 nitridng, the lifter and slider shelf is 738H. Please check the information above!
23．现在到了吃午钣的时间，我们下午再继续好吗？
It is time to have lunch, let's discuss this project later this aft ernoon?
24．和滑塊干涉的倒勾請加料填平至滑塊可以順利滑動
The undercut area interferes with the slide block and needs to be filled with material to help the slider move smoothly.
25．加肉太多
The thickness added is too thick.
26．加肉面積太大
The thickening area is too wide.
27．GATE位置移位
The gate position is moved.
28．滑塊拆的位置
The split line of slide block or the area of slide.
29．此處有尖角，填充困難.
It is hard to fill this area due to the sharp feature.
30．此處鋼材太薄，強度不足而且不容易冷卻.
The strength of this area is too weak and it is hard to cool because the steel is too thin. 31．圓柱特徵要有一半圓不可以拆在滑塊上，以免粘滑塊造成拉白，拉斷.
We avoid designing the semicircle of the cylinder on the slide block because it will be
pulled apart or cause drag marks.
32．此處做斜銷在作動時會削到成品肉厚
The part will be damaged if we make the lifter in this area.
33．這個面是裝配面，不能加料
This is a critical surface where we cannot add additional material.
34．此處料位太厚，會有縮水，建議減料改善
Because of the shrinkage of the thickness, we suggest reducing some wall thickness to
improve it.
35．此面是不是外觀面，此處做滑塊的話會有夾線，是否可以接受
Please confirm whether it is a critical surface or not. Also, confirm whether it is
acceptable to have a slide split line if we have a slide in this area.
36．此處有倒勾，能否減料，使公母模靠破，不做滑塊和斜銷.
Please confirm whether we can reduce material to the area where we have an undercut as indicated to have shut off on cavity side. No slide block and lifter will be made. 37．請盡快確認這種拆模方式和結構，否則會影響模期
Please confirm the issues of Parting line, Gate position...Etc. as soon as possible;
otherwise, the lead-time will be extended.
38．此面是否有特殊要求，能否有頂針印
Please confirm whether it is a critical surface or not and if we can have E.J. pin marks on it.
39．P.L面開在此處，模具上會有尖角和刀口，對模具壽命有影響.
There are sharp edges if we set the parting line here, It will reduce the tool life.
40．加大拔模角，以便脫模順利
We suggest enlarging the draft angle to help release the to ol.
41．GATE做在此處的話有兩個缺點：1.蓋子打開時可以看到GATE的修剪部位; 2.
兩個斜銷在同一側，頂出也不是很平衡.
There are two problems if the gate is to be designed in this area:
a). It is easy to see the gate mark when you open the cap.
b). The ejectors are unbalanced when two lifters are on the same side.
42．GATE做在此處的話.蓋子打開後看不到GATE的修剪部位
The gate mark is not visible if the gate position is designed like this.
43．如果GATE一定要做在你們指定的位置的話，那還不如做在這一側，這樣的話還可以減小這個位置的縮水
If you insist that the gate position has to be like the original design, then we would
further recommend to have it to the area indicated so it can avoid a shrink problem in
this area.
44．在此處GATE做潛頂針的話，背後的外觀面會有沖料痕，而且成品又是黑色的，會最明顯.
If the design of the gate has to be a sub. Gate, then the back surface of the part will have serious flow marks due to the black color.
45．P.L開在此處不合理，模具加工困難，P.L應改為和圖示的一樣
This area is not suitable to have a Parting line because the tool will become more
complicated; therefore, we recommend to have the Parting line as indicated.
46．产品粘母模的機會很大，能否在公模加倒勾，拉料頂針或者公模保留E.D.M紋，開模時使成品留在公模一側
There is possible sticking on cavity; therefore, please confirm whether it can make
undercuts, snatch pins or leave coarse E.D.M. on the core to snatch the part on
47．此處料厚段差很大，成品表面會有應力痕，是否接受?
Please confirm whether it is acceptable to have stress lines on the surface because the
thickness is not equal.
48．請注明何處為外觀面，能否提供2D圖和注意事項.
Please advise where the critical surface is. Please also provide us a 2D drawing with
critical dimensions.
49．紅色所示處是有問題的地方，請特別注意
Please note the red highlights because those areas have prob lems.
50．成品設計此處有問題，建議如下圖所示修改
We would suggest using the attached part design as the current design has problems.
51．此處改為一個球形的凹槽
We suggest modifying it as a globe recess.
52．圓柱特征要有一半不可以拆在滑塊裡，以防拉斷
this issue is the same as no.31
53．此處大滑塊上走小滑塊，小滑塊要先退，大滑塊要做延遲
The inside small slide block will recede first and the paren t slide block have to postpone sliding.
54．滑塊要用液壓油缸抽芯以保証開合模順序
The slide pins will use an oil cylinder to assure that the process is in proper order.
55．這個面有裝配，加料的話裝配時會頂住，如圖所示
We cannot add material to this surface because it will intervene between the two parts when it is assembled. Please see the sketch attached.
56．可降低斜銷面，增加成品些許肉厚來做變化
To descend the surface of lifter in order to thicken the part.
57．一半做斜銷，一半做自然
One half side will have the lifter and the othe r half will be solid/nature.
58．此處兩個柱子重疊，有倒勾，不能做自然，要做SLIDE
These two bosses are overlapping with undercut therefore it can not be made as solid.
We suggest making it with a slide block.
59．此處強迫頂出
This area needs force ejection.
60．公模兩段開模，這個地方先退
Here will be a double ejection for forward and receding.
61．此處做鑲件會有夾線，能否接受
Please confirm whether it is acceptable that there will be a split line here.
62．此面公母模1度靠破，會有段差，可否接受
Please confirm whether it is ok to have mismatch to the area where there is 1 degree of shut off in Core / Cavity side.
63．這個尺寸能否加大
Please confirm whether we can enlarge this dimension.
64．此處加一個凹槽，膠片的彈出效果會更好一些，試模後看裝配的效果再做修正It will affect the elastic of the film better if we add a recess. See how it will affect the
assembly parts, and then make your decision.
65．此處有倒勾，建議將剖面線所示部位CUT即可避免此處的倒勾There is an undercut here, we suggest cutting out the indicated part as it highlighted to avoid an
undercut.
66．成型後SUB GATE要修平
The gate (sub gate) needs to be trimmed evenly after being moulded.
67．此處倒勾先垂直頂出，之後再手動取出
This area of the undercut needs to be ejected vertically, then taken out manually.
67. 這兩個面都有滑塊，GATE改在此處改不到
The gate is not suitable in this area because there are two sliding blocks sealing off this area.
68．此處加做一個旋轉GATE，射出時方便調整成品的品質
We would suggest placing a runner shut-off insert to adjust the volume of part filling. 69．此倒勾在滑塊上強迫脫模，倒勾是否可以減小到0.6
This undercut will be force ejected out, Please confirm whether it can be reduced to 0.6 mm.
70．此柱子無法脫模，請確認是否是在轉圖時錯位，能否提供客戶的原始圖檔data.
This boss is not releasable. Please check the file again and if possible, pleas re-send us
the original draft.
71．此柱子是實心的，會縮水
This boss will shrink because it is a solid boss.
72．這個面是否要咬花，咬花番號是什麼，最小的拔模角要多大Please confirm whether this surface needs to be textured or not. Please advise texture specs. Also,
what's the min. draft.
73．這個面是否要打光，貼標簽
Please confirm whether this surface needs to be polished and stuck on a sticker.
74．紅色顯示的幾個面拔模角太小，出模時會拉傷，建議加大拔模角The red highlighted area has a problem of a small draft angle. We suggest enlarging
thedraft to avoid causing drag marks on the part.
75．此RIB太薄，會填充不足
This rib can not be filled properly because it is too thin.
76．此RIB太厚，會縮水
This rib will have a shrink problem because it is too thick.
77．此處倒勾出模困難，建議先不做倒勾，成型後再二次加工，但要做治具，費用要另外算
There are problems with this current design, we recommend doing this undercut as an
alternative but there will be additional costs.
78．柱子底部都要做火山口
The base of all bosses require a crater to avoid shrinkage.
79．镶件，P.L.面有充足排气坑，P.L.面要开环形排气槽,并能将气体排到模外。
Insert/PL should have adequate venting, PL sho uld have around slot for venting.
80．顶棍孔镶件端面距离底板面0,5mm,攻m20牙;
the surface of KO insert should below bottom plate 0.5mm,thread M20.
81．回针，中托司与模胚部份避空0.5mm；
RP,EGP should have 0.5mm gap with the mold base.
82．排气槽距封胶位10-15mm；
Venting slot distance from the seal off position 10-15mm
83．运水进用 E ，运水出用S ；
In take "E", Out take "S"
84．底面板均要有隔热板,DME规格1/4厚；
Top/Bottom plate must have insulator plate, DME standard 1/4'H
85．吊环要在模具的重心（保证吊模时的平衡）;
Eyebolt should on the center of the mold(for balance)
86．吊模螺丝的位置要在前/后模部份的重心,保持平衡；
The eyebolt position on the cavity/core side should on the center of gravity for balance 87．唧嘴分试模唧嘴/走模唧嘴;
Sprue type: Trial/Delivery
88．喉塞选用：NPT规格;
Plug use NPT spec.
89．中托司采用HASCO滚珠形式.
Use HASCO ball EGP
90．水咀采用法国标准:1/4"的水咀写:RPL08-1151
Jiffy Use French Standard: 1/4" mark:RPL08-1151
91．全部使用英文和英制单位
All in English& Imperial Unit
92．请检查内模尺寸有否乘缩水?
Are part dimensions to print plus shrink?
93．凡有电线通过的角位要改为R角，是否完成
All wires protected from sharp corners？
94．所有替换的元件必须是标准件。
All replaceable components must be standard components.
95．是否加啤塑总计器？
Add shot counter?
96．一个复杂的模具，设计经过周详考虑，成功地克服了各种设计上的限制。
A complicated mould with thorough design consideration to overcome the numerous
design constraints.
97．所有移动的零件应使用硬钢料，行位必须用硬垫板和硬线条，而且必须有限位及定位锁。
All moving components should use hardened steel: all slide s should be installed with
hardened or lubricated alloy wear plates and gibs, and with positive slide retainer.
98．BOM的内容应包含运水接头,顶针和自制的零件.
BOM including water fittings, ejectors &custom components.
99．若没有运水回路，斜顶为铍铜。
BeCu for lifters if w/o water circuits。
100．对应的部件在前、后模平面视图中镜像
Corresponding components mirrored at core &cavity
101．有否省光就出模?
Check polish for line of draw finish？Core pull slot mechanism installed and O.K. 102．模具须用多大吊机才可搬动
Crane capacity and loading clearance.。
103．经流道及变形电脑模拟分析。
Conduct mold flow &mold warp analysis.
104．散件图或3D模具图
Component and/or 3D mould design drawing.
105．若尺寸不重要，适量冷却也可。
Cooling less important when dimensions are not important.
106．将一个标准四模腔大水口模具与一个四模腔倒转大水口模具结合成为一套可于同一大小的注塑机，生产量可增加一倍的层板模具，并且可降低成本。
Combine a traditional 4 cavity edge gate and a4 cavitie s reverse gate moulds which help to double the molding capacity and reduce production cost.
107．此模具最大的特式是，可将模具分开变成两套，在不同地方生产，增加生产的灵活性。
Can be separated into two individual moulds for molding in two different mould shops. 108．由于全套模具均利用模具标准零件制成，在维修及换零件上比较方便。
Consists of all standard mould components which facilitate mould maintenance. 109．出模方向的标示
Die draw called out
110．标出前、后模距离，滑动部件滑动距离和塑件脱离的位置
Dimension all the opening , travel & clearance
111．是否使用DME运水接头及编号?
DME egg. Water fittings recessed and marked?
112．开箱后是否容易吊出模具及是否分开前/后模运输？
Delivery right side up , or in two halves？
113．吊模孔尺寸，平衡，2边都要有
Eyebolt size and balance in 2 sides
114．出行程、行位、斜顶行程的标注
Ejection stroke & slide, lifter travel dimensioned。
115．若有斜顶，做出分析。
Ejection study if lifter adopted
116．顶出到极限位置。
Ejection extended at the most
117．顶针导柱的安装
Ejector guide pins installation .
118．重量大于50lbs的镶件必须要有吊模孔。
Eyebolts for inserts more than 50lbs.
119．边缘型或直入型水口都可以接受。
Edge gate or sprue gate requiring secondary operation acceptable.
120．斜顶和与其接触的内模或镶件在硬度上有4度的差别（HRC）。
4 point in HRC different to lifters contacting or cavity steel。
121．水口及水口顶针的4倍放大视图，按实际尺寸标注。
4X size section, dimensioned to reflect the actual size.
122．常规、安全和搬运要求
General ,safety and handling
123．建议模具用于锁模力超过100吨的注塑机，或有1.5mm以下的顶针或顶出行程超过50mm时，应装上顶针板导柱。
Guided ejection recommended for mould above 100 tons clamp capacity, ejector pins of
1.5mm or smaller, or ejector stroke longer than 50mm.
124．边钉插入模板有否顶着及加疏气空?
Guide pin cleared and vented?
125．镶件定位和编号以防止不正确的组装。
Inserts keyed and numbered to prevent incorrect assembly.
126．面角度要比行位斜边角度大3度(<25度)。
Jaw angle 3 deg.more than angle pins(<25 degree).
127．在行位、斜顶、主要镶件处保留足够位置（空间）布置水槽。
Keep enough space to run waterline at slide /lifter/major inserts.
128．斜顶角度小于15度。
Lifter angle less than 15 degree.
129．斜顶杆直径不能少于1"。
Lifter rods dia, less than 1"
130．是否已安装限位制？
Limit switch in tact and protected.
131．模坯和钢料号的标注
Mold-base and steel dimensioned
132．斜顶镶件最小5度插穿
Minimum 5 deg.for shut-off.。
133．动作机构是否正确？
Mechanism for sequence
134．是否已安装安全带及喷上正确颜色在模坯上？
Mold safety straps installed and painted red？
135．适宜应用模拟的模具注塑过程，注射分析、压力分布及温度分布以确定最佳入水位置、流道尺寸和疏气位置等。
Mould flow and simulation should be carried out for the best gate location, filling
analysis, pressure distribution and heat distribution.
136．模具在设计上要做到尽快冷却，上、下内模高温点应该有个别的冷却，应有适量顶针。
Mould should be designed with maximum cooling and with appropriate amount of
ejection points.
137．模具能够全自动生产，大的零件应由机械手拿出。
Mould should be able to run fully automatic. Large part should be picked up by robot. 138．模具经过测试，符合预定的Cpk质量标准。
Mould should be tested to meet a defined Cpk quality standard.
139．模具应具备可以预防意外损害及错误安装等安全特性。
Mould should have safety features to protect accidental damage, incorrect assembly and set up of mould.
140．上、下模需要精确配合或有擦位的地方，模具一定要有直身锁。Mould halves requiring accurate alignment of core and cavity, and shut off should have appropriate
part line locks.
141．需要加热的模具，必须有隔热板。
Mould requiring heating should have insulator plate.
142．模具最好能自动生产，模具尽可能自断水口。
Mould preferred to run automatic; self-degating whenever possible.
143．模具必须稳定位置如有凸出物请加脚座，是否完成？
No obstructions on bottom surface of mold？
144．模坯长宽和模厚（模架的长宽）
Overall mold size of the moldbase & shut height
145．出入水位有否打上IN 、OUT 字码？
Outlets accessible and marked " IN OUT and NUMBER"？
146．画出突出部件并做好保护。
Protruding items shown and protected。
147．合模分布在合理可接受的表面。
Parting line at the acceptable surface.
148．尽可能布置多的运水。
Put waterline as much as possible/wherever possible。
149．尽可能在行位、斜、镶件布置运水。
Put waterline for slide /lifter/insert wherever possible.
150．分模线是否正确?
Parting line cleared and released properly?
篇二: 电话英语对话中常用的礼貌用语
电话英语对话怎么说呢?和外国人交谈，电话交谈，掌握一些电话英语对话中常用的礼貌用语还是很有必要的。[)你掌握了多少电话英语的表达方法呢，下面我们一起了解下：
一、不太会讲英语的要怎么说：
(1)请稍待片刻。
Just a moment, please.
(2)请等一下。我找个人来听。
Hold on, please. I'll get someone to thephone.
(3)请别挂断。我找一位会说英语的人来。
Hold the line, please. I'll get an English speaker.
(4) 很抱歉，我英语说得不好。我找位会讲英语的人稍后回电话给你。请教您的大名及
电话号码?
I'm sorry, I don't speak English well. I'll have an Englishspeaker call you back later. May I have your name and telephonenumber?
二、接电话的开场白
(1) 早安。这里是正泰贸易公司。我能效劳吗?
Good morning. This is Chengtai Trading Company. May I helpyou?
(2) 喂。海外营业部。我是王大明。
Hello. Overseas Sales Department. Taming Wang speaking.
(3) 先锋电子。我是吴玛莉。
Pioneer Electronics. This is Mary Wu speaking.
(4) 午安。这里是大安商业银行。我能为您效劳吗?
Good afternoon. This is Dan An Commercial Bank. What can I dofor you?
(5) 喂。这里是王公馆。
Hello. This is the Wang residence.
(6) 午安。我是王大明。
Good afternoon. Taming Wang speaking.
(7) 我是杨文凯，请讲。
Wenkai Yang. Speaking
三、不明了对方所言时
(1) 能说得明确一点吗?
Could you put that in more specific terms?
(2) 很抱歉。我没听懂你的话。
I'm sorry. I couldn't follow you.
(3) 我无法确定你的意思。
I'm not sure what you mean.
(4) 你讲得太快了。我跟不上。
You're talking too fast. I can't keep up.
(5) 你能说得简单一点吗?
Could you put that more simply?
(6) 请你再多解释一下好吗?
Will you explain a little bit more?
四、通话将毕时的结尾语
(1)谢谢你来电。
Thank you for calling.
(2)很高兴跟你谈话。
Nice talking to you.
(3)感谢你打给我。
It was kind of you to call me.
(4)请随时再打电话给我。
Call me again any time.
(5)我该挂电话了。
I'd better get off the phone.
(6)让我们尽快聚聚。
Let's get together soon.
(7)有空请再打电话来。Call again when you've got time.
塑胶模具常用英语句型
塑胶模具常用英语句型 1. XXX！你现在有空吗，我可以问你一些问题吗？ Could I ask you some questions if you are free？/ Are you free now？ May I ask you some questions (a question)？ 2. 请问此产品的面是否为外观面？表面做什么处理？是晒纹/抛光？ Can you tell me whether the surface of this part is a visible/esthetic one？ What will we do for its？Surface？Texture or Polishing？ 3. 请问产品这个面可否加顶针或顶块？产品允许加扁顶针吗 Does this part need an ejector pin or an ejector bar? Can we add an ejector blade? 4. 这个产品的柱位我们打算做司筒。（或镶针）可以吗？ Can we add ejector sleeves or ejector pins in the boss of this part? 5. 产品的这个位置不能出模，我们打算做行位，在此面上会有分模线，你接受吗？ There's an undercut at this position and it needs a slider. It will also have a parting line on this side, is that OK? 6. 产品里面的这个位置我们打算做斜顶或内行位，有问题吗？ We will make the lifter and (inner) slider in this position, will that be a problem? 7. 你提供的2D产品图与3D产品图不一致，请问以哪一个图面为准？ The 2D and 3D drawing you provided is not the same, can you tell me which one is correct? 8. 你提供的3D产品图有的地方没有出模角，有的地方胶位太厚，有的地方胶位太溥，这些产品问 题我们可以自己修改吗？修改后会给交给你确认。 There is no draft angle in the 3D drawing, some materials are too thick, and some place are too thin. Can we modify this part by ourselves? We will send the drawing to you for you to check after we modify it. 9. 按你们提供的缩水率千分之五，这个模具的尺寸已经做到了模具图面要求。但注塑出来的产品 不符合你们的产品图。请确认你们的材料的缩水率是否正确？ According to the shrinkage one over two hundred, the mold has been done in the right dimension, but the part falls short to your part drawing, are you sure the shrinkage is right? 10. 产品的这个位置太小，导致模具钢料太溥，能够加宽这个位置吗？ This position is too small and will make the steel material here too thin, can we widen it here? 11. 斜顶与后面的柱位空间太小，斜顶在运动时会干涉到柱子，能移动这个柱子的位置吗？ The angular lifter interferes with the boss during ejection. Please consider changing the position of the boss. 12. 这个筋骨位胶厚太薄，而且高度偏高，注塑时很难填充这个筋位，可以增加这个筋骨位的厚度吗？ The rib here is too thin and on the high side, so it will be difficult to fill here when we do the injection, can you increase the thickness of this rib? 13. 你是想将此筋骨位的高度加高/减低吗？加胶的位置我们将用铜公放电加深。但减胶的位置有两 种做法，1、做镶件；2、烧焊；因为镶件的底部有运水，我们简单的做法是烧焊处理，你可以接受吗？ Will you increase/decrease the material on this rib? We will use EDM if you add material, but there are two option if you choose to decrease: 1. Make inserts;2 Welding, because there is water in the bottom of the insert, is that OK? 14. 这个样板的筋骨位底部烧焦，是因为排气不良，我们可以在筋骨位的中间增加一个镶件。
咖啡厅常用英语口语情景对话
Hao: Good morning madam. What can I get you? Hao: 早上好，您要点什么？ Jenny: I’d like a coffee please. Jenny: 我要一杯咖啡。 Hao: Certainly madam, what kind of coffee would you like? Hao: 您要哪一种？ Jenny: What have you got? Jenny: 你们都有什么？ Hao: Well we have espresso, cappuccino, latte, skinny latte or americano. Hao: 我们有义式浓缩咖啡，花式咖啡，拿铁咖啡，脱脂拿铁咖啡或美式咖啡。 Jenny: Goodness me! What a choice! I think I’ll have a cappuccino please Jenny: 这么多种类! 请给我一杯花式咖啡吧。 Hao: Here you are. You’ll find the sugar just over there. Hao: 给您，砂糖就在那边。 Ling: Would you like something to drink? Ling: 你想喝点什么？ Jenny: Yes please. Do you have any teas? Jenny: 好的，你们有茶吗？ Ling: Of course we have lots of teas? Ling: 当然，我们有很多。 Jenny: What do you recommend? Jenny: 你给推荐一种吧？ Ling: What about a green tea or perhaps a jasmine tea? Ling: 你看绿茶或茉莉花茶，怎么样？ Jenny: What’s this one? Jenny: 这是什么？ Ling: That’s Oolong tea – it’s a Cantonese tea. Ling: 这是乌龙茶-是一种广东茶。 Jenny: Ok, I’ll try that. Jenny: 好吧，我想试试。 What can I get you? 你要点什么？ What have you got? 你们有什么? What do you recommend? 你给推荐一下好吗？ I’ll try that. 我来试试那个。
英语日常情景对话
情景对话 你有什么计划吗？ Nancy：Have a nice weekend! 周末好！ Jerry：Thanks. You too! 谢谢！你也好！ Nancy：Do you have any plans? 你有什么计划吗？ Jerry：Well, my family's away and I can't afford to do much. What about you? 嗯，我家里人都走了，我承受不起做太多的事。你呢？ Nancy：Oh, I haven't decided what I'm going to do yet. 哦，我还没决定我要做什么呢。 这几天真是太打扰你了 John：Have you had a good time these past few days? 这几天玩得怎么样啊？ Lily：Yes. Kunming is really a beautiful place. 好极了。昆明这地方真漂亮。 John：Thank you. You're welcome here anytime you want. 谢谢夸奖。什么时候想来就过来玩儿。 Lily：I'm afraid I've been a bother these past few days. 这几天真是太打扰你了。 John：Don't mention it. You know, we're old friends. 别这么客气。咱俩都老朋友了。 Lily：Well. Please come to Beijing if you have time, and let me do the honors. 好。有时间的话，一定来北京玩儿，让我也尽尽地主之宜。John：Okay. Have a safe trip. 好的。一路顺风。
模具术语(中英文对照)
AD-Diameter The tread diameter at the centerline of the tread (EU); also: "T-Diameter"(GT) AD直径：指胎面中心线直径（EU）。又叫T直径（GT） Auto-lock Ear A Lug on the cone ring used to mount the mold/container in the top half of a 60“ NRM Auto-lock press. 导环上的突缘，用于和60“ NRM Auto-lock 硫化机上半部连接。 Bead Ring The tire bead forming ring (also: toe ring) 钢圈，也称toe ring Bead Ring Register The landing and tapered seat that the bead ring fits into 钢圈配合：侧板上，和钢圈配合的平面及锥面 Bottom Container Plate The plate that the bottom sidewall plate is bolted to 模壳底座 Bottom Container Plate Lifting Lug A lug attached to the Bottom Container Plate with Horizontal holes used for lifting. 模壳底座吊耳：装配在底座上、有水平的孔，用来吊装的吊耳 Bottom Container Plate Dowel Pin Lug A lug attached to the Bottom Container Plate that supports the Dowel Pin Bushing. 装配在底座上，用来支承定位销套的突缘 Bottom Container Plate Hold Down A lug that is used to fix the Bottom Plate in the Press. 用来将底座装配在硫化机上的突缘 Breaker Hook A hook fixed to the bottom of the tread segment that catches the bottom container plate only when the segment will not release from the tire during de-molding. 分离钩：固定在花纹块底部的钩子，轮胎硫化完后若花纹块不能跟轮胎分离，就用此钩抓住模壳底座帮助花纹块和轮胎进行分离。
常用模具零件中英文对照表
常用模具零件中英文对照表 2005-12-19 14:51:17???中国注塑网 入水：gate 进入位：gate location 水口形式：gate type 大水口：edge gate 细水口： pin-point gate 水口大小：gate size 转水口：switching runner/gate 唧嘴口径：sprue diameter 二、流道: runner 热流道：hot runner,hot manifold 热嘴冷流道: hot sprue/cold runner 唧嘴直流: direct sprue gate 圆形流道：round(full/half runner 流道电脑分析：mold flow analysis :?[??n?l?s?s] 流道平衡:runner balance 热嘴：hot sprue 热流道板：hot manifold 发热管：cartridge heater 探针: thermocouples 插头：connector plug 插座： connector socket 密封/封料： seal 三、运水：water line 喉塞：line lpug 喉管：tube 塑胶管：plastic tube 快速接头：jiffy quick connector plug/socker 四、模具零件：mold components 三板模：3-plate mold 二板模：2-plate mold 边钉/导边：leader pin/guide pin 边司/导套：bushing/guide bushing 中托司：shoulder guide bushing 中托边：guide pin 顶针板：ejector retainer plate 托板：support plate
(完整word版)英语日常用语情景对话
?日常用语： 就是日常生活中的交际用语，如Thank you. Sorry.等 谚语： 即是人们生活中常用的现成的话。 谚语类似成语，但口语性强，通俗易懂，而且一般都表达一个完整的意思，形式上差不多都是一两个短句。 例如：Helaughsbestwholaughslast.谁笑到最后，谁就笑得最好。 Nopains,nogains.没有付出，就没有收获。 ?英语日常交际用语分类： 打招呼与告别用语（Greeting and Saying Good-bye） 1.－How are you ? －I’m fine, thanks. 2. －Nice to meet you. －Nice to meet you, too. 谈论颜色（Talking about colour） 1. －What colour is it? －It’s red. 2. －What’s you favourite colour, Jenny? －My favourite colour is blue. 3. －How many colours do you like? －Three. 谈论高度（Talking about height） 1. －Are you short or tall? －I’m short／tall. 2. －How tall am I, Mr Wood? －You’re 1.6 metres tall. 看病用语（Seeing a doctor） 1. －What’s the matter? －I cut my knee. It hurts. 就餐用语（Having meals） 1. －Would you like some dumpling? －No, thanks.／ Yes please. 2. I’d like porridge for breakfast. 3. It’s ／Thery’re delicious. 4. What would you like for supper? 5. －Are you ready to order? －Yes, please. I’d like……. 谈论天气（Talking about weather） 1 －How is the weather today?／What’s the weather like today?
塑胶模具专业英语
中文英文 机工,机器加工 machining,machine work O环,O形封垫 O ring 下料模,切料模 blanking die 寸进,寸动 inching 工程塑胶 engineering plastics 工模,夹具,支架 jig 干胶,粘著剂,动物胶 glue 干燥时间 drying time 干燥剂 drier dryer 不划一颜色,颜色深浅不均 color non-uni formity 中心浇口 center gate 内衬,衬套,衬蛰 liner 公差,容差 tolerance 分模线,合模线,模缝痕 parting line 切口,缺口 notch 切口,缺料 notch 切边(n) shear edge 化学腐蚀 chemical atching 化学腐蚀 chemical etching 反射 reflection 孔隙,空洞,气泡 void 尺寸稳定性 dimensional sability 手动压机 hand press 支管形喷嘴 nozzle manifold 比重 specific gravity 比热 specific heat 毛状裂痕 hair crack,hair cracking 毛绒 fuzz 毛边,凿纹 burr,flash,fin 水道,水通路 water channel 火花放电 spark discharge 火焰处理 flame treatment,flame treating 片材 sheet 凹痕,缩痕 sink mark,shrink mark 凹槽,内陷,凹陷 undercut 加料,给料,供料 feed 加热,加温 warming,warming up 加热板,热板(盘) heating plate 加热管套,加热缸 heating cylinder,heatin g barrel 加热炉 heating furnace 功率,力率 power factor 半透明 semitransparence,translucence 打眼,钻孔 driling 正余面,交叠,重叠 overlap 永久变形 permanent set,residual strain 白昙,雾状 haze 立式射出成型机 vertical injection mo(u)l ding machine 光彩,光泽 gloss 印刷 printing 同轴往复螺杆式射出成型机 in-line scre w(type)injecton mo(u)lding machine 合成树枝 synthetic resin 合板,集成材 composite wood 合模力,开模力 mo(u)ld clamping force, mo(u)ld locking force 合模线,毛边线 flash line,parting line 合模线,毛边线 spew line,spue line 合模销,导销 leader pin 合模销套,导销衬套 leader pin pushing 合模机构,开模机构 mo(u)ld clamping m echanism 后加工 post processing 后加热 after baking 后成型 postforming 回程销,复归销 return pin 安全系数 safety factor 安全门 safety door 成孔销,心型销,模蕊销 core pin 成孔销托板,动或定模板 core pin plate 成形 forming 成形,模制 mo(u)iding,forming
商场常用英语情景对话
关于购物对话用语 一、问好 hello/hi 你好 Nice to meet you. 见到你很高兴。 Nice to meet you too. 见到你很高兴。How are you 你好吗 I am fine, thank you, and you 我很好，你呢I am fine too. 我也很好。 How do you do 你好。（初次见面问候语）How do you do 你好。 二、迎宾 Welcome to Prada! 欢迎来到普拉达专卖！ 三、打招呼 Good morning, sir/ madam早上好，先生/女士afternoon下午evening晚上What can I do for you/ May I help you 您需要什么 I am looking for/ need/ want to buy a... 我需要买...... Do you have any ... 你们有...... I'm just looking/ browsing.我只是随便看看。 四、询问衣服 How are these 这些怎么样 This one is great. May I try this on这款很不错。我可以试试吗 Sure, the fitting/dressing room is there.当然可以，试衣间在那边。 What's your size/ What size do you want你穿多大号的 Size (S, M, L, XL, XXL...)/数字 OK/ Is it fit 可以吗/合适吗 The fit isn't good. 尺寸不合适 It is too big/ small. Can I have a larger/ smaller size 太大了/太小了. 可以给我个大一点/小一点的吗 I’m sorry, it is out of stock for the time being.很抱歉，这个暂时缺货。 It fits well. 很适合 How do I look/ What do you think/ Does this look good on me 这件我穿着怎么样 You look very good. 你看起来很不错。 I will take it. 我要这件。 五、询问价格 How much does it cost/ is it 这件多少钱What is the price for this suit/...这套西装/......多少钱 5025 yuan/ dollars It's so expensive./ It costs too much.太贵了Can you make it cheaper能便宜些吗 Can you give me any discount/ Any discount 能给我一点折扣吗
吃饭英语日常对话情景.doc
吃饭英语日常对话情景 吃饭英语日常对话情景：invitation邀请 A：Jerry,would you be interested in dinner with me ? B：Thank you for your invitation，I m free tonight。 A：Which food do you like best? chinese food or western food? B：I prefer some Chinese traditional food。 A：I ll pick you up at 7:00。 B：Thank you 吃饭英语日常对话情景：ready to order A：What would you like to drink? beer,coffee or tea? B：Tea is fine. A：A pot of dragonwell tea。一壶龙井 A：What would you like to eat? yangzhou fried rice扬州炒饭or west lake beef soup? B：I wanna some west lake beef soup. 西湖牛肉羹 What is your special?你们的特色菜是什么?特色菜the specials= specialty A：Would you like anything else? B：No, I m fine 吃饭英语日常对话情景：请客 A：Thanks for lunch. It was delicious. 谢谢你请的午餐。它
很美味。 B：It s OK. 不客气。 A：Next time lunch is on me. 下次的午餐我请。 B：Don t be silly. 别傻了。 A：I m serious. 我是认真的。 B：All right. Next time you will treat. 好的。下次你请。 A：It s a deal. 一言为定。 重点词汇： 口语里It s a deal. 是很常见的，尤其是遇到谈话双方对某一交易或事情达成一致意见时，就会用到这句话，表示一言为定。
英语日常情景对话有用的情景对话资料28324
二十一个场景对话 目录 1、你有什么计划吗？ (2) 2、这几天真是太打扰你了 (3) 3、英文问路指路 (4) 4、这位子有人坐吗？ (6) 5、打电话预定餐厅位子 (8) 6、商务宴会中的英文点菜方式 (10) 7、At Breakfast 吃早餐 (14) 8、如何用英语买火车票 (16) 9、谈薪水必备英语口语 (17) 10、On a Bus 在公共汽车上 (21) 11、Asking Favors 求助 (23) 12、Making an Appointment 预约 (25) 13、Saying Goodbye 告别 (26) 14、Meeting old friends 老友重逢 (28) 15、Saying Thank You 道谢 (30) 16、介绍和开场白 (32) 17、Finding a Room 找住房 (34) 18、At a Hotel 在旅馆 (36)
19、The weather 天气 (38) 20、这里停车每小时多少钱？ (39) 21、为什么突然要辞职呢？ (40) 1、你有什么计划吗？ Nancy：Have a nice weekend! 周末好！ Jerry：Thanks. You too!
谢谢！你也好！ Nancy：Do you have any plans? 你有什么计划吗？ Jerry：Well, my family's away and I can't afford to do much. What about you? 嗯，我家里人都走了，我承受不起做太多的事。你呢？ Nancy：Oh, I haven't decided what I'm going to do yet. 哦，我还没决定我要做什么呢。 2、这几天真是太打扰你了 John：Have you had a good time these past few days? 这几天玩得怎么样啊？ Lily：Yes. Kunming is really a beautiful place. 好极了。昆明这地方真漂亮。
模具专业英语——注塑模
Injection Mold Technical Terms 特克内克腾目思 （一）模具专业基本用词 Professional Terms Intensification Factor 增强比 Scientific molding 科学注塑英腾次分克深发克偷 塞音特菲克计数器counter康特 Specific Injection Pressure (Psi)特殊注塑压力 思呗色服克 1．塑料—plastic, resin瑞申油管：Oil pipe 尼龙--------nylon 2．样件—sample 调节板-------adjust plate 3．钢料—steel A板--------a plate 4．注塑机—injection machine, press 定位圈----locating ring 喽客厅令 5．产品—part, product, moulding 斜导柱-----angular pin 安给拉PIN 6．模具—mold, mould, tool B板--------- b plate A 简易模（样板模）—prototype mold B 量产用模具—production mold 7．三维造型（数模）—3D model, 滚珠导套-------ball ejector bush 8．二维产品图—2D part drawing 拽应扁顶针--------blade ejector pin 布累得 9．设计—design 低赛应下模板--------bottom clamping plate 抱腾 10．制造—manufacture, 上模型腔------cavity main insert 11．检验—check, 上模镶件------cavity sub insert 12．测量—measure, 妹试司筒针--------center pin 深特 13．修改—change, modify 下模型芯------core main insert 14．工程更改—engineer change 下模镶针------core pin 15．质量—quality 快乐体下模镶件------core sub insert 16．数量—quantity 宽体踢延迟顶针-------delay ejector pin 17．基准—datum, reference 拉杆限位钉--------distance bolt （二）如何解析2D 产品图？How to read 2D part drawing? 一．产品几何Geometry 顶距限位柱--------distance spacer 1．点—point 销钉-------dowel pin 2．线（边）—line, edge 顶块--------ejector bar 3．面face 顶板导套-----ejector leader pin A 侧面—side塞得 B表面—surface射飞思 C 外观面—appearance surface安皮尔思射飞思4．壁厚—wall thickness 我射克来思顶板导柱----ejector leader pin李德拼 5．加强筋（骨位）—rib 瑞布顶针-------ejector pin 6．孔—hole后顶针地板------ejector plate 7．细长的槽—slot 顶针面板-----ejector retain plate 瑞腾 8．柱位—boss 抱死顶棍------ejector rod
英语情景对话——常用
英语情景对话——常用 英语情景对话一 对春节期间的烟花爆竹燃放问题的讨论 A：Happy new year, LIU, It is nice to enjoy New year holiday, but the noise of the fireworks and firecrackers bothers me recently. B: Happy new year, On the contrary,I think the fireworks and firecrackers is as nice as the Spring festival. A:Oh no, A t New Year’s Eve, I was up all night because there is too much noise outside. I think fireworks and firecrackers should be prohibited. B:I may not agree with you. The noise of them is a symbol of lively festive atmosphere. And I set off some fireworksat New Year’s Eve. It’s so interesting. A: Ok, the noise, is a piece of cake, it is just for me. But fireworks and crackers will cause air pollution. When firework is set off, it will produce lots of sulfur dioxide which is harmful to our environment. What’s more, fireworks and crackers do lots of harm to people. To make the matter worse, children love playing carelessly with firecrackers, which more often cause conflagration. B: Yeah, some of what you have said is true and It should cause the attention of people. But as long as people pay attention to safety when setting off, I think, It'sunderstandable to set off fireworks and firecrackers during the festival and they should not be prohibited. A:There also exist potential hazards in manufacturing, shipping and storing them. B: As a traditional way to celebrate the New Year, quite a few people think firecrackers have become part of our Chinese culture. Lots of fun will be gone with the ban of firecrackers. A: True, to change a custom is not easy, and people are not ready for such drastic action, but it will pay in the long run if the setting off of firecrackers is effectively banned in the cities. B: Maybe, we can celebrate our holiday by other ways instead of setting off firework.
英语日常情景对话有用的情景对话
英语日常情景对话有用 的情景对话 文档编制序号：[KK8UY-LL9IO69-TTO6M3-MTOL89-FTT688]
二十一个场景对话目录 1、你有什么计划吗 Nancy：Have a nice weekend! 周末好！ Jerry：Thanks. You too! 谢谢！你也好！
Nancy：Do you have any plans? 你有什么计划吗 Jerry：Well, my family's away and I can't afford to do much. What about you? 嗯，我家里人都走了，我承受不起做太多的事。你呢 Nancy：Oh, I haven't decided what I'm going to do yet. 哦，我还没决定我要做什么呢。 2、这几天真是太打扰你了 John：Have you had a good time these past few days? 这几天玩得怎么样啊 Lily：Yes. Kunming is really a beautiful place. 好极了。昆明这地方真漂亮。 John：Thank you. You're welcome here anytime you want. 谢谢夸奖。什么时候想来就过来玩儿。 Lily：I'm afraid I've been a bother these past few days. 这几天真是太打扰你了。
John：Don't mention it. You know, we're old friends. 别这么客气。咱俩都老朋友了。 Lily：Well. Please come to Beijing if you have time, and let me do the honors. 好。有时间的话，一定来北京玩儿，让我也尽尽地主之宜。 John：Okay. Have a safe trip. 好的。一路顺风。 3、英文问路指路 A: Excuse me, Where am I on this map? B: We are here, bus station, we are in the heart of the city. A: Oh ! I think I’m lost. Can I go from here to the railway station? B: Head straight up the street about two blocks then turn left. A：对不起，请问我在地图上的什么地方? B：我们在这里，汽车站，我们现在在市中心。
4英语口语日常情景对话用语
英语口语日常情景对话用语 一、祝愿、祝贺和应答（Good wishes, congratulations and responses） 1.- Well done and congratulations to you. - Thanks very much. 2.- I hope you‘ll succeed in everything. - So do I. 3.- I wish you success. - Thank you. 4.- We send you our best wishes. - Thank you very much. 5.- Happy new year ! - Happy new year! (The same to you.) 6.- A merry Christmas to you. - Thank you. 7.- I hope you‘ll have a good time. - Thank you. 8.- Happy birthday! - Thank you. 二、邀请和应答（Invitations and responses） 1.- Would you like to come to the party? - Oh yes, thank you. 2.- I hope you can come to the dance next Saturday. - I‘m sorry, but I can‘t. 3.- Will you go dancing with us? - Of course. I‘ll be glad to. 4.- Will you come to our English Evening? - Yes, thank you. 5.- Would you please give us a talk on English Learning? - OK. When? 6.- You and your friends must come over to my house and see
模具注塑术语中英文对照
根据国家规范，以下为部分塑料模具成形术语的规范翻译。 动模Movable Mould Moving Half 定模座板Fixed Clamp Plate Top Clamping Plate Top Plate 动模座板Moving Clamp Plate Bottom Clamping Plate Bottom Plate 上模座板Upper Clamping Plate 下模座板Lower Clamping Plate 凹模固定板Cavity-retainer Plate 型芯固定板Mould Core-retainer Plate 凸模固定板Punch-retainer Plate模套Die Body Die Sleeve Die Blank支承板Backing Plate Support Plate 垫块Spacer Parallel 支架Ejector Housing Mould Base Leg模头Die Head 模具分类8 Injection Mold 注塑模Plastic Rubber Mould 塑胶模Rubber Molding 橡胶成 形 Hot Chamber Die Casting 热室压铸Sand Mold Casting 砂模铸造 Extrusion Mold 挤出模Multi-Cavity Mold 多模穴模具 Palletizing Die 叠层模Plaster Mold 石膏 模Three Plates Mold 三板模Plain Die 简易模Pierce Die 冲孔模 Forming Die 成型模Progressive Die 连续模 Gang Dies 复合模Shearing Die 剪边模Cavity Die 型腔模 Riveting Die 铆合模Compression Molding 压缩成型Flash Mold 溢流式模具 Extrusion Mold 挤压式模具Split Mold 分割式模具Mould Cavity 型腔母模Mold Core 模芯公模Large Die Mold 大型模具Precise Die Mold 精密模具 Complex Die Mold 复杂模具Foaming Mould 发泡模具 Metal Die 金属模具Plastic Mold 塑料模具Tool Stamping Die Punch Die 冲压模具 Extrusion Die 挤压模具Graphite Die 石墨模具流道浇口部分Runner System 浇道系统Sprue Cold Material Trap 浇道冷料井Sprue Puller 拉杆 Runner Design 流道设计Main Runner 主流道 Secondary Runner 次流道Mould Gate Design 浇口设 计 Submarine Gate 潜伏浇口Tunnel Gate 隧道式浇口Pinpoint Gate 点浇口Fan Gate 扇形浇口 Side Gate 侧浇口Edge Gate 侧缘浇口 Tab Gate 搭接浇口Film Gate 薄膜浇口Flash Gate 闸门浇口Slit Gate 缝隙浇口 Dish Gate 盘形浇口Diaphragm Gate 隔膜浇口 Ring Gate 环形浇口Runnerless 无浇道 Sprueless 无射料管方式Long Nozzle 延长喷嘴方式 Sprue 浇口，溶渣Insulated/ Hot Runner 热浇 道Runner Plat 浇道模块Valve Gate阀门浇口Slag Well 冷料井Cold Slag 冷料渣 Sprue Gate 射料浇口Nozzle 射嘴 Sprue Lock Pin 料头钩销（拉料杆）注塑缺陷Flash 飞边Warpage 翘曲Air Trap 积风Blush 发赤Flow Line 流痕Splay 银纹Short Shot 短射Sink Mark 缩痕Streak 条纹Void 缩孔Weld Line 熔接线 Gas Mark 烧焦Cold Slug 冷斑Delamination 起皮Burr 毛刺Flaw Scratch 刮伤Gloss 光泽 Glazing 光滑Surface Check 表面裂痕Hesitation 迟滞注塑工艺Molding Conditions 成型条件Drying 烘干Barrel Temperature 料筒温度Melt Temperature 熔化温度 Mold Temperature 模具温度Injection Pressure 注塑压力Back Pressure 背压Injection Speed 注塑速度Screw Speed 螺杆转速Tensile Strength 抗拉强度T ensile Elongation 延伸率Flexural Modulus 弯曲模Flexural Strength 抗弯强度Shrinkage 收缩率Regrind Usage 次料使用Moulding 模塑机械设备 Lathe 车床Planer 刨床Miller / Milling Machine 铣床Grinder 磨床Driller 钻床Linear Cutting 线切割Electrical Sparkle 电火花Welder 电焊机Punching Machine 冲床Robot 机械手Common Equipment 常用设备EDM Electron Discharge Machining 放电加工3D Coordinate Measurement 三次元量床Boring Machine 搪孔机Contouring Machine 轮廓锯床Copy Grinding Machine 仿形磨床Cylindrical Grinding Machine 外圆磨床Die