英文机械图纸常用翻译词句

冲压模具专业词汇中英文翻译

Counter bored hole 沉孔 Chamfer 倒斜角 Fillet 倒圆角 padding block垫块 stepping bar垫条 upper die base上模座 lower die base下模座 upper supporting blank上承板 upper padding plate blank上垫板 spare dies模具备品 spring 弹簧 bolt螺栓 document folder活页夹 file folder资料夹 to put file in order整理资料 spare tools location手工备品仓 first count初盘人 first check初盘复棹人 second count 复盘人 second check复盘复核人 equipment设备 waste materials废料 work in progress product在制品 casing = containerization装箱 quantity of physical inventory second count 复盘点数量 Quantity of customs count 会计师盘,点数量 the first page第一联 filed by accounting department for reference会计部存查 end-user/using unit(department)使用单位 Summary of year-end physical inventory bills 年终盘点截止单据汇总表 bill name单据名称 This sheet and physical inventory list will be sent to accounting department together (Those of NHK will be sent to financial department) 本表请与盘点清册一起送会计部－(NHK厂区送财会部) Application status records of year-end physical inventory List and physical inventory card 年终盘点卡与清册使用－状况明细表 blank and waste sheet NO. 空白与作废单号

机械图纸中英文翻译2(1)1

近几年，我厂和英国、西班牙的几个公司有业务往来，外商传真发来的图纸都是英文标注，平时阅看有一定的困难。下面把我们积累的几点看英文图纸的经验与同行们交流。 1标题栏 英文工程图纸的右下边是标题栏（相当于我们的标题栏和部分技术要求），其中有图纸名称（TILE）、设计者（DRAWN）、审查者（CHECKED）、材料（MATERIAL）、日期（DATE）、比例（SCALE）、热处理（HEAT TREATMENT）和其它一些要求，如： 1)TOLERANCES UNLESS OTHERWISE SPECIFIAL 未注公差。 2)DIMS IN mm UNLESS STATED 如不做特殊要求以毫米为单位。 3)ANGULAR TOLERANCE±1°角度公差±1°。 4)DIMS TOLERANCE±0.1未注尺寸公差±0.1。 5)SURFACE FINISH 3.2 UNLESS STATED未注粗糙度3.2。 2常见尺寸的标注及要求 2.1孔（HOLE）如： （1）毛坯孔：3"DIAO+1CORE 芯子3"0+1; （2）加工孔：1"DIA1"; （3）锪孔：锪孔(注C＇BORE=COUNTER BORE锪底面孔); （4）铰孔：1"/4 DIA REAM铰孔1"/4; （5）螺纹孔的标注一般要表示出螺纹的直径，每英寸牙数（螺矩）、螺纹种类、精度等级、钻深、攻深，方向等。如：例1.6 HOLES EQUI-SPACED ON 5"DIA (6孔均布在5圆周上（EQUI-SPACED=EQUALLY SPACED均布） DRILL 1"DIATHRO＇ 钻1"通孔（THRO＇=THROUGH通） C/SINK22×6DEEP 沉孔22×6 例2.TAP7"/8-14UNF-3BTHRO＇ 攻统一标准细牙螺纹，每英寸14牙，精度等级3B级 （注UNF=UNIFIED FINE THREAD美国标准细牙螺纹） 1"DRILL 1"/4-20 UNC-3 THD7"/8 DEEP 4HOLES NOT BREAK THRO钻1"孔，攻1"/4美国粗牙螺纹，每英寸20牙，攻深7"/8,4孔不准钻通（UNC=UCIFIED COARSE THREAD 美国标准粗牙螺纹） 1"-14NS-2THRO 攻美国固定特种螺纹M1",每英寸牙数14,精度等级为二级 （注NS=NATIONAL SPECIAL THREAD:美国固定特种标准）

机械工程英语_第二部分翻译

Unit5 INDUSTRIAL ROBOT工业机器人 INTRODUCTION介绍 Industrial robots are relatively new electromechanical devices that are beginning to change the appearance of modern industry. Industrial robots are not like the science fiction devices that possess human-like abilities and provide companionship with space traveler、Research to enable robots to “see，"hear"，“touch"，and "listen" has been underway for two decades and is beginning to bear fruit. However，the current technology of industrial robots is such that most robots contain Only an arm rather than all the anatomy a human possesses. Current control only allows these devices to move from point to point in space，performing relatively simple taskes. The Robotics Institute of America defines a robot as“a reprogramrnable multifunction manipulator designed to move material，parts, tools，or other specialized devices through variable programmed motions for the performance of a variety of tasks. "' A NC machining center would qualify as a robot if one were to interpret different types of machining as different functions- Most manufacturing engineers do not consider a NC machining center a robot，even though these machines hive a number of situ- ilarities. The power drive and controllers of both NC machines and robots can be quite similar. Robots, like NC machines can he powered by electrical motors，hydraulic systems，or pnetinlat tc svsterns. Control for either device can lye either open-loop or closed-loop. In fact，many of the developments used in robotics have evolved from the NC industry，and many of the manufactur- ers of robots also manufacture NC machines or NC controllers.工业机器人是相对来说较新的机电设备， 它已经开始改变现代工业的面貌。工业机器人不像科幻小说中的那个模样具有人一样的能力并且能与

机械图纸中常用词汇英语缩写 汇总

机械图纸英语翻译 以下是我在工作中常用的ALLWELDSCONTINUOUSUNLESSOTHERWISESTATED.未注焊缝均为连续焊 ALLWELDS3mmFILLETUNLESSOTHERWISESTATED未注焊角高3mm. ALLUNSPECIFIEDRADI-R3未注圆角R3 REMOVEALLBURRSANDSHARPEDGES棱角倒钝 CHANNEL槽钢 RSA708角钢70X70X8 M30X1.5pitchM30X1.5的锥螺纹 Tackweld点焊 OD1/4"outsidedimension1/4"的缩写外径直1/4" 75CRS尺寸为75材质为冷轧钢板 410OPENINGREF410开口参考尺寸 40REF尺寸为40,参考值 2.5"BSP2.5”圆锥管螺纹 2.5"BSPTHEXAGON2.5”六角圆锥管螺纹(即对丝) 30x2.5FLATBAR30X2.5扁钢 TYP2POSNS2处 11TOTALCOILSAPROX.9WORKINGCOILSAPROX.RIGHTHANDW

OUNDONLY,ENDCOILSSQUARETOTOUCH. 总圈数约11圈；工作圈数约9圈；右旋；弹簧的端部磨平以便于接触.(此为弹簧技术说明) FEMALE:内扣(母扣) MALE:外扣(公扣) 偏心轴eccentricshaft 销轴PIN 开口销COTTERPIN 螺杆screw 紧定螺钉SETSCREW 圆螺母ROUNDNUT 内六角螺钉SOCKETHEADCAPSCREW 六角螺钉HEXHDSETSCREW 六角螺栓HEXHDBOLT 挡圈closingring 弹性挡圈circlip 轴承隔套distancesleeveofaxletree 轴承axletree 深沟球轴承DEEPGROOVEBALLBEARING 无扣长non-bucklelongth 弹簧SPRING 吊环螺钉LIFTINGEYEBOLT

机械专业术语英文翻译

陶瓷 ceramics 合成纤维 synthetic fibre 电化学腐蚀 electrochemical corrosion 车架 automotive chassis 悬架 suspension 转向器 redirector 变速器 speed changer 板料冲压 sheet metal parts 孔加工 spot facing machining 车间 workshop 工程技术人员 engineer 气动夹紧 pneuma lock 数学模型 mathematical model 画法几何 descriptive geometry 机械制图 Mechanical drawing 投影 projection 视图 view 剖视图 profile chart 标准件 standard component 零件图 part drawing 装配图 assembly drawing 尺寸标注 size marking

技术要求 technical requirements 刚度 rigidity 内力 internal force 位移 displacement 截面 section 疲劳极限 fatigue limit 断裂 fracture 塑性变形 plastic distortion 脆性材料 brittleness material 刚度准则 rigidity criterion 垫圈 washer 垫片 spacer 直齿圆柱齿轮 straight toothed spur gear 斜齿圆柱齿轮 helical-spur gear 直齿锥齿轮 straight bevel gear 运动简图 kinematic sketch 齿轮齿条 pinion and rack 蜗杆蜗轮 worm and worm gear 虚约束 passive constraint 曲柄 crank 摇杆 racker 凸轮 cams

(机械制造行业)机械英文翻译

英文翻译 机械设计 一台完整机器的设计是一个复杂的过程。机械设计是一项创造性的工作。设计工程师不仅在工作上要有创造性，还必须在机械制图、运动学、工程材料、材料力学和机械制造工艺学等方面具有深厚的基础知识。 Machine Design The complete design of a machine is a complex process. The machine design is a creative work. Project engineer not only must have the creativity in the work, but also must in aspect and so on mechanical drawing, kinematics, engineerig material, materials mechanics and machine manufacture technology has the deep elementary knowledge. 任何产品在设计时第一步就是选择产品每个部分的构成材料。许多的材料被今天的设计师所使用。对产品的功能，它的外观、材料的成本、制造的成本作出必要的选择是十分重要的。对材料的特性必须事先作出仔细的评估。 One of the first steps in the design of any product is to select the material from which each part is to be made. Numerous materials are available to today's designers. The function of the product, its appearance, the cost of the material, and the cost of fabrication are important in making a selection. A careful evaluation of the properties of a. material must be made prior to any calculations. 仔细精确的计算是必要的，以确保设计的有效性。在任何失败的情况下，最好知道在最初设计中有有缺陷的部件。计算（图纸尺寸）检查是非常重要的。一个小数点的位置放错，就可以导致一个本可以完成的项目失败。设计工作的各个方面都应该检查和复查。 Careful calculations are necessary to ensure the validity of a design. In case of any part failures, it is desirable to know what was done in originally designing the defective components. The checking of calculations (and drawing dimensions) is of utmost importance. The misplacement of one decimal point can ruin an otherwise acceptable project. All aspects of design work should be checked and rechecked. 计算机是一种工具，它能够帮助机械设计师减轻繁琐的计算，并对现有数据提供进一步的分析。互动系统基于计算机的能力，已经使计算机辅助设计（CAD）和计算机辅助制造（CAM）成为了可能。心理学家经常谈论如何使人们适应他们所操作的机器。设计人员的基本职责是努力使机器来适应人们。这并不是一项容易的工作，因为实际上并不存在着一个对所有人来说都是最优的操作范围和操作

中英文文献翻译-国内高空作业机械行业现状及发展方向

附录 Present situation of access working vehicles industry and its development stratagem in China Our work in the machinery production in the late 1970s, rapid development, started the current production management enterprise with several rapidly increased to over 40, and foreign joint ventures or cooperative enterprises have five production. According to 2004 and 2005《the Chinese mechanical engineering yearbook》，2003 annual aloft working machinery industrial output for 32139 million yuan, the production of various kinds of aerial work platform 1906, aerial work platform car 7.4, In 2004, aloft working machinery industrial output for 36340 million yuan, the production of various kinds of aerial work platform 2500, car 800 sets. In recent years, through several backbone enterprise industry technical transformation, the production scale expands unceasingly, formed the respective characteristics of the products can meet the domestic market # aerial work machinery need, its main economic index of enterprise economic benefits are rising gradually, increasing. 1 Aloft working machinery industry development present situation 1.1 To improve product performance Our aloft working machinery industry backbone enterprises of some use their equipment and technology advantages, through the study, the introduction and digest its own technology and equipment, through the study, introduce advanced foreign technology and developed many new products, the products of the technical level and product quality is improving, and close to the international similar product level # promoted aloft working machinery industry in the domestic market and technological progress in competitive and market demand, the yield increased rapidly. If Beijing hoisting machine factory developed self-traveling shear fork platform, the spider type folding boom platform, aluminum mast section of the box. One box type aluminum mast section of the largest single mast operation platform will reach the height of 16.5 m, Hangzhou and engineering machine's more mast 22m reached alloy platform, hangzhou aichi engineering vehicles Co., LTD develop full hydraulic driving type self-traveling aerial work platform, the maximum height of 26.7 m homework. The above products fill the blank, domestic products have reached the international advanced level. In addition, in the car factory products, fushun crane, jinzhou heavy machinery Co., LTD, xuzhou construction machinery group and chongqing dajiang industrial (group) Co., LTD has developed over 30 aloft work, broken fire only depending on the imported products of domestic situation of the weak. 1.2 Product category and quantity increasing Our work with the mechanical product demand of national economy and the development of urban construction increased year by year, all kinds of new products increased rapidly in recent years. If Beijing hoisting machine factory in just a few short

机械专业外文翻译中英文翻译

外文翻译 英文原文 Belt Conveying Systems Development of driving system Among the methods of material conveying employed，belt conveyors play a very important part in the reliable carrying of material over long distances at competitive cost．Conveyor systems have become larger and more complex and drive systems have also been going through a process of evolution and will continue to do so．Nowadays，bigger belts require more power and have brought the need for larger individual drives as well as multiple drives such as 3 drives of 750 kW for one belt(this is the case for the conveyor drives in Chengzhuang Mine)．The ability to control drive acceleration torque is critical to belt conveyors’ performance．An efficient drive system should be able to provide smooth，soft starts while maintaining belt tensions within the specified safe limits．For load sharing on multiple drives．torque and speed control are also important consideratio ns in the drive system’s design. Due to the advances in conveyor drive control technology，at present many more reliable．Cost-effective and performance-driven conveyor drive systems cov ering a wide range of power are available for customers’ choices[1]. 1 Analysis on conveyor drive technologies 1．1 Direct drives Full-voltage starters．With a full-voltage starter design，the conveyor head shaft is direct-coupled to the motor through the gear drive．Direct full-voltage starters are adequate for relatively low-power, simple-profile conveyors．With direct fu11-voltage starters．no control is provided for various conveyor loads and．depending on the ratio between fu11- and no-1oad power requirements，empty starting times can be three or four times faster than full load．The maintenance-free starting system is simple，low-cost and very reliable．However, they cannot control starting torque and maximum stall torque；therefore．they are

机械图纸英语翻译

1，PERMANENTLY MARK PART NUMBER(ALL METHODS ACCEPTABLE)IN LOCATION SHOWN：SAME AS DWG NO.INCLUDING REV & DATE OF MFG 2，REMOVE ALL BURRS AND BREAK ALL EDGES 3，ALL DIMENSIONS AND TOLERANCES APPLY AFTER FINISHING(IF REQUIRED) 4，COSMETIC INSPECTION CLASS IIA-EXTERNAL COMPONENT 5，MATERIAL：LAMINATED 1/2" CORIAN；COLOR SPECIFIED IN PURCHASE ORDER 6，FINISH：LAMINATION TO APPEAR SEAMLESS;NO PITTS OR LINES POST MACHINING：CLEAN & FURTHER SPECIFICATION IN PO 7，POLISHING：IF SPECIFIED IN PO；TOP，SIDES，CHAMFER & 1/2" FROM EDGE ON BASE SURFACE 8，ARTWORK：IF SPECIFIED IN PO；TO BE READ FROM ELLIPTICAL PROFILE 9，PART TO BE MANUFACTURED REFERENCING DWG AND 3D GEOMETRY SUPPLIED 2，1.如图所示的位置上加上耐久的产品编号标记,就是图纸编号包括图纸版本号及生产日期. 2.除去所有毛刺及所有边倒角. 3.(如必要的话)产品表面处理后,所有的尺寸及公差要符合要求. 4.外观检测等级为【信息工业协会[美]-外观件】 5.产品材料:1/2 英寸厚的"可丽耐"薄板, 颜色在采购单内注明. 6.表面要求:层压后无结合线,无凹坑或凸凹线状, 后处理: 洁净及详细请看采购单说明. 7.表面抛光: 如果在采购单中有说明则按其要求做,否则顶部,侧面,倒角斜面及底边上来1/2英寸处要抛光. 8.美工; 如果在采购单中有说明则按其要求做,否则从椭圆形中来读取(这一点要能与你们专业有关,我就不是很清楚, 要看产品图才知) 9.产品加工请参照提供的工程图及三维立体图. Assembly line 组装线 Layout 布置图 Conveyer 流水线物料板 Rivet table 拉钉机 Rivet gun 拉钉枪 Screw driver 起子 Electric screw driver 电动起子 Pneumatic screw driver 气动起子 worktable 工作桌 OOBA 开箱检查 fit together 组装在一起 fasten 锁紧(螺丝) fixture 夹具(治具) pallet 栈板

机械图纸英语缩写

以下是我在工作中常用的 ALL WELDS CONTINUOUS UNLESS OTHERWISE STATED. 未注焊缝均为连续焊 ALL WELDS 3mm FILLET UNLESS OTHERWISE STATED 未注焊角高3mm. ALL UNSPECIFIED RADI - R3 未注圆角R3 REMOVE ALL BURRS AND SHARP EDGES 棱角倒钝CHANNEL 槽钢 RSA 708 角钢70X70X8 M30X1.5 pitch M30X1.5的锥螺纹Tackweld 点焊 OD 1/4" outside dimension 1/4"的缩写外径直1/4" 75 CRS 尺寸为75 材质为冷轧钢板 410 OPENING REF 410 开口参考尺寸 40 REF 尺寸为40,参考值 2.5" BSP 2.5”　 圆锥管螺纹 六角圆锥管螺纹(即2.5" BSPT HEXAGON 2.5”　 对丝) 30x2.5 FLAT BAR 30X2.5 扁钢 TYP 2 POSNS 2处 11 TOTAL COILS APROX.9 WORKING COILS APROX.RIGHT HAND WOUND ONLY,END COILS SQUARE TO TOUCH.

总圈数约11圈；工作圈数约9圈；右旋；弹簧的端部磨平以便于接触.(此为弹簧技术说明) FEMALE: 内扣(母扣) MALE: 外扣(公扣) 偏心轴eccentric shaft 销轴PIN 开口销COTTER PIN 螺杆screw 紧定螺钉SET SCREW 圆螺母ROUND NUT 内六角螺钉SOCKET HEAD CAP SCREW 六角螺钉HEX HD SETSCREW 六角螺栓HEX HD BOLT 挡圈closing ring 弹性挡圈circlip 轴承隔套distance sleeve of axletree 轴承axletree 深沟球轴承DEEP GROOVE BALL BEARING 无扣长non-buckle longth 弹簧SPRING 吊环螺钉LIFTING EYE BOLT 开槽盘头螺钉SLOTTED PAN HEAD SCREW

机械专业相关词汇中英文翻译大全

机械专业相关词汇中英文翻译大全 单价unit price 工日合计Man-day total/work-day total 人工费cost of labor 材料费materials expenses 机械的mechanical 检查接线connection test 发电机generator 调相机phase regulator 周波cycle 减负荷装置 load-shedding equipment 断路器柜circuit breaker cabinet 单母线single busbar 互感器transformer 每相电流Current by Phase 封闭式插接close type socket joint 发电机控制面板generator control panel 分级卸载sorted unloading 同步控制synchronization control 调速器 speed governor 信号屏signal screen 继电器relay 高压柜high pressure cabinet 油浸电力变压器oil-immersed power transformer 空气断路器air circuit breaker 控制屏control panel 直流馈电屏direct current feed control panel 电容器electric condenser 计量盘metering panel 成套配电箱whole set of distribution box 落地式floor model 控制开关Control switches 铜芯电力电缆Copper core power cable 控制电缆actuating cable 热缩式电力电缆终端头pyrocondensation power cable terminal 钢结构支架配管steel structure bracket tubing 万用槽钢versatile U-steel 电缆托架 cable bracket 钢制托盘式桥架steel Tray-type cable support system waterproof socket 防水插座 防爆插座Explosion-proof socket 接地绞线earthing twisted pair 接地母线 earthing bus

纺织品印花常见术语的英文翻译

纺织品印花常见术语的英文翻译 蒸化(aging) 自动筛网印花(automatic screen printing) 满地印花(blotch print) 烂花印花(burn—out prints) 涪烘(curing) 直接印花(direct prints) 拔染印花(discharge prints) 干法印花(dry prints) 双面印花(duplex prints) 静电荷(electrostatic charge) 静电植绒(electrostatic flocking) 按特殊要求印花(engineered print) 叠印(fall on) 平板(flatbed) 植绒印花(flock printing) 植绒(flocking) 半色调或中间色调(halftone) 手工筛网印花(hand screen printing) 热转移印花(heat--transfer printing) 喷射印花(jet printing) 机械植绒(mechanical flocking) 罩印(over print) 印花色浆(print paste) 大木印花胶浆(DM print binder) 对花(registration) 防染印花(resist printing) 滚筒印花(roller printing) 圆形筛网印花或圆网印花(rotary screen printing) 筛网印花(screen printing) 打样(strike off) 热转移印花(thermal transfer printing) 经纱印花(warp prints) 湿罩干印花(wet—On—dry) 湿罩湿印花(wet—On—wet) 湿法印花(wet prints) 印花对花准确／对花不准(print register／off register) water based printing 水印 heat transfer printing 热转移印花

机械专业术语英文翻译

机械专业英语词汇 陶瓷ceramics 合成纤维synthetic fibre 电化学腐蚀electrochemical corrosion 车架automotive chassis 悬架suspension 转向器redirector 变速器speed changer 板料冲压sheet metal parts 孔加工spot facing machining 车间workshop 工程技术人员engineer 气动夹紧pneuma lock 数学模型mathematical model 画法几何descriptive geometry 机械制图Mechanical drawing 投影projection 视图view 剖视图profile chart 标准件standard component 零件图part drawing 装配图assembly drawing 尺寸标注size marking 技术要求technical requirements 刚度rigidity 内力internal force 位移displacement 截面section 疲劳极限fatigue limit 断裂fracture 塑性变形plastic distortion 脆性材料brittleness material 刚度准则rigidity criterion 垫圈washer 垫片spacer 直齿圆柱齿轮straight toothed spur gear 斜齿圆柱齿轮helical-spur gear 直齿锥齿轮straight bevel gear 运动简图kinematic sketch 齿轮齿条pinion and rack 蜗杆蜗轮worm and worm gear 虚约束passive constraint 曲柄crank 摇杆racker

中国出版社名录中英文对照

中国出版社名录（中英文对照）A 安徽大学出版社Anhui University Press 安徽教育出版社Anhui Education Press 安徽科学技术出版社Anhui Science & Technology Publishing House 安徽人民出版社Anhui People’s Publishing House B 北京出版社Beijing Publishing House Group 北京大学出版社Peking University Press 北京工业大学出版社Beijing University of Technology Press 北京航空航天大学出版社Beijing University of Aeronautics &Astronautics Press 北京科学技术出版社Beijing Science &Technology Press 北京理工大学出版社Beijing Insititute of Technology Press 北京师范大学出版社Beijing Normal University Press 北京图书馆出版社Beijing Library Press 北京邮电大学出版社Beijing University of Posts and Telecommunications Press 北京语言文化大学出版社Beijing Language and Culture University Press 兵器工业出版社The Publishing House of Ordnance Industry C 中国地图出版社(原：测绘出版社) SinoMaps 成都地图出版社Chengdu Cartographic Publishing House 重庆出版社Chongqing Publishing Group 重庆大学出版社Chongqing University Press D 大连出版社Dalian Publishing House 大连理工大学出版社Dalian University of Technology Press CO.,LTD 地震出版社Seismological Press 地质出版社Geological Publishing House

机械设计专业术语地英语的翻译

机械设计专业术语的英语翻译 阿基米德蜗杆 Archimedes worm 安全系数 safety factor; factor of safety 安全载荷 safe load 凹面、凹度 concavity 扳手 wrench 板簧 flat leaf spring 半圆键 woodruff key 变形 deformation 摆杆 oscillating bar 摆动从动件 oscillating follower 摆动从动件凸轮机构 cam with oscillating follower 摆动导杆机构 oscillating guide-bar mechanism 摆线齿轮 cycloidal gear 摆线齿形 cycloidal tooth profile 摆线运动规律 cycloidal motion 摆线针轮 cycloidal-pin wheel 包角 angle of contact 保持架 cage 背对背安装 back-to-back arrangement 背锥 back cone ； normal cone 背锥角 back angle 背锥距 back cone distance 比例尺 scale 比热容 specific heat capacity 闭式链 closed kinematic chain 闭链机构 closed chain mechanism 臂部 arm 变频器 frequency converters 变频调速 frequency control of motor speed 变速 speed change 变速齿轮 change gear ; change wheel 变位齿轮 modified gear 变位系数 modification coefficient 标准齿轮 standard gear 标准直齿轮 standard spur gear 表面质量系数 superficial mass factor 表面传热系数 surface coefficient of heat transfer 表面粗糙度 surface roughness 并联式组合 combination in parallel 并联机构 parallel mechanism 并联组合机构 parallel combined mechanism 并行工程 concurrent engineering 并行设计 concurred design, CD 不平衡相位 phase angle of unbalance 不平衡 imbalance (or unbalance) 不平衡量 amount of unbalance 不完全齿轮机构 intermittent gearing 波发生器 wave generator 波数 number of waves 补偿 compensation 参数化设计 parameterization design, PD 残余应力 residual stress 操纵及控制装置 operation control device 槽轮 Geneva wheel 槽轮机构 Geneva mechanism ； Maltese cross 槽数 Geneva numerate 槽凸轮 groove cam 侧隙 backlash 差动轮系 differential gear train 差动螺旋机构 differential screw mechanism 差速器 differential 常用机构 conventional mechanism; mechanism in common use 车床 lathe 承载量系数 bearing capacity factor 承载能力 bearing capacity 成对安装 paired mounting 尺寸系列 dimension series 齿槽 tooth space 齿槽宽 spacewidth 齿侧间隙 backlash 齿顶高 addendum 齿顶圆 addendum circle 齿根高 dedendum 齿根圆 dedendum circle 齿厚 tooth thickness 齿距 circular pitch 齿宽 face width 齿廓 tooth profile 齿廓曲线 tooth curve 齿轮 gear 齿轮变速箱 speed-changing gear boxes 齿轮齿条机构 pinion and rack 齿轮插刀 pinion cutter; pinion-shaped shaper cutter 齿轮滚刀 hob ,hobbing cutter 齿轮机构 gear 齿轮轮坯 blank 齿轮传动系 pinion unit 齿轮联轴器 gear coupling 齿条传动 rack gear 齿数 tooth number 齿数比 gear ratio