对夹式高性能蝶阀

Jamesbury样本W104-1 发布于2003/11

3”– 24” (DN80 - 600) Series 860 ANSI CLASS 600 WAFER-SPHERE HIGH PERFORMANCE

BUTTERFLY VALVES

3”– 24” (DN80 - 600) 860系列600磅级高性能蝶阀

Series 860 ANSI Class 600 high-performance Wafer-Sphere butterfly valves provide tight shutoff, excellent flow characteristics, and long service life. They are available in 3” -24” (DN80 -600) sizes in wafer-style body design (860W) and in single-flange lugged design(860L)

860系列600磅级高性能对夹式蝶阀关闭紧密，流通性能良好，使用寿命长。3” -24” (DN80 -600) 之间有对夹式（860W）和单法兰凸耳式（860L）。

The series 860 Wafer-Sphere butterfly valve is available in a variety of materials in standard, Fire-Tite, NACE MR0103 construction and valves conforming to the European Pressure Equipment Directive (PED)97/23/EC or PED requirements. Optionally available are valves specifically prepared for chlorine, oxygen, high-vacuum, and abrasive service.

860系列对夹式蝶阀标准型可使用多种材料，防火，NACE MR0103 结构，阀门符合欧洲压力设备指令(PED)97/23/EC或其要求。其他可选阀门要求可指定，如氯气、氧气、高真空或颗粒磨损介质。

FEATURES 特征

Xtreme

*New Xtreme seat provides longer life, expanded performance boundaries and greater value.

新的Xtreme阀座使用寿命长，性能范围扩大，附加值高。

Field-Proven Single-Piece Flexible PTFE Seat Design

已证实的单面弹性PTFE阀座设计

*No additional o-rings or metal parts required to maintain tightness.

不需o型圈或金属零件以保持紧闭性

*Lip-seal design compensates for temperature and pressure changes.

唇形密封设计可补偿温度和压力变化

*Longer service life with less maintenance. 维护更少，寿命更长

*Tight shut-off in either direction. 双向紧闭

Easy Seat Maintenance

阀座容易维护

*Simply remove body insert and replace seat; disassembly of disc and shaft is not required.

只需移除阀体镶件就可更换阀座，不需拆卸阀瓣和阀杆

Excellent For Both On-off And Control Applications

切断和控制应用良好

*Superior control characteristics. 优良的控制性能

*Inherent flow characteristic is modified equal percentage. 内部流通性能调成均等的比例

*Wide rangeability. 使用范围广

*Tight shut-off even in control applications. 即使用于控制应用也能关闭紧密

*Standard lugged style valves are suitable for bi-directional dead-end service at the full pressure-temperature rating of the valve.

标准的凸耳式阀门可在阀门最大温压下双向完全开启

Fire-tested Version Available 防火标准可选择

*Fire-Tite Wafer-Sphere valves have been tested to API 607 and BS6755 part 2.

防火型对夹阀门可接受检测标准有API607和BS 6755 第二部分。

Single Source Responsibility 单一采购责任

*Purchase valves, actuators, and accessories, completely mounted, from one source.

仅从一家采购阀门、执行和配件或完全安装好的阀门部件

*Available with electric, manual gear, and pneumatic double-acting or spring-return actuators and a variety of accessories including limit switches, solenoids, and positioners.

可使用电动、手动齿轮箱、气动双作用或弹簧复位执行器以及大量配件包括限位开关、电磁阀和定位器

Additional Information 其他信息

Please refer to the bulletins listed below for additional information on other Jamesbury high-performance butterfly valves.

关于其他Jamesbury高性能蝶阀的相关信息，请参阅下列阀门样本。

Wafer-Sphere Polymer(soft)-Seat HP Butterfly Valves 对夹聚合物（软）阀座高性能蝶阀ASME/ANSI Classes 150 & 300 W101-6

ASME/ANSI Classes 150(Process Rated过程额定) W105-1

Cryogenic Service 超低温介质W130-1

Steam Service 蒸汽介质W150-1

Chlorine Service 氯气介质W150-2

Oxygen Service 氧气介质W150-3

Vacuum Service 真空介质W150-4

Jacketed Valves 夹套阀门W151-3

SPECIFICATIONS参数

Seat Rating 阀座等级

阀座等级基于阀瓣全关状态下的不同压力，仅适用于阀座。不同材料的阀体最大工作压力和检测压力显示于下列阀体压力等级表

这些等级是常规介质的保守性指导。过往流体经验或新的发展以及其他阀体材料或可允许高于下述压力的应用。具体推荐请咨询美卓公司总部。

Seat Ratings for Series 860 Valves, Shaft Downstream 860系列阀门、阀杆下游阀座等级

温度

Note：

Type 860 and Type F860 valves are rated for a maximum differential pressure of 1000 psi (68.95bar) when installed in the non-preferred flow direction (shaft-upstream).

Type 860 and Type F860 valves with 316 stainless steel shafts are rated for a maximum differential pressure of 1000 psi (68.95 bar) in either installation direction.

备注：

860型和F860型阀门安装在非优先流向（阀杆上游）时，额定最大压差为1000psi (68.95bar)。含316不锈钢阀杆的860型和F860型阀门安装在任意方向，其额定最大压差为1000psi。

流量参数

上述表格提供的是本册样本中860W和860L阀门的流量系数，Cv值代表60°F的水的流通能力; 即流量系数。

公制Kv值等于Cv值乘于0.8569。或者Cv=1.167Kv。

Valve Body Ratings 阀体等级

These are maximum working pressure ratings of the Valve Body Only. These seat ratings above determine the practical pressure limitations according to actual service conditions. Test pressures below are for a hydrostatic test with the valve open.

下面是阀体的最大工作压力等级。上述阀座压力等级决定了实际使用工况的压力限制。下列检测压力是指阀门开启状态下的液压测试。

Valve Torque Data 阀门扭矩参数

The torque required to open or close Series 860 and F860 valves can easily be calculated using the equation below. However, for your convenience, the tables on page 4 can be used as a quick guide for actuator selection. If the valve’s torque is not listed I the tables, (use the equation to calculate the torque). Refer to Jamesbury bulletins for pneumatic and electric actuators. Select an actuator that provides the same or greater torque output than the valve’s torque. If in doubt, select the next larger actuator. Refer to these bulletins for pneumatic and electric actuator torque output valves and actuator selection tables.

启闭860 and F860系列阀门所需的扭矩很容易通过下列公式计算出来。然而下一页（原文第四页）的表格可作为执行器快速选型指南。如果阀门扭矩不在表中，则通过公式计算。参阅Jamesbury气动和电动执行器的样本。选择比阀门扭矩相同或更大扭矩输出的执行器。如有疑虑，可选择再大一点的执行器。气动和电动执行器的扭矩值和选型可参阅下面的样本资料。

Manual Gear Actuators 手动齿轮箱A100-1

Piston Actuators (ST Series) 活塞执行机构A102-1

Piston Actuators(BC/BJ Series) 活塞执行机构A107-1

Torque Equation 扭矩公式

Use the following equation (and the factors extracted from the table below) to calculate the torque required to open or close Series 860 valves.

使用下列公式（扣除下表中的因素）计算启闭860系列阀门所需的扭矩

Torque required (FT·LBS) = ｛（kt）*（shut-off differential pressure in psi）｝=Ts

扭矩(FT·LBS) = ｛（kt）*（紧闭时压差psi）｝=Ts

Example 例如:

6”(DN150)860W-11-36HBXZ at 900psi (62.055bar), installed shaft downstream.

(From table, Kt=0.195, Ts=80.)

= 256 FT·LBS ( To convert to N·m, multiply by 1.356)

阀门尺寸；阀杆上游；阀杆下游；扭矩公式因素；阀杆上游或下游

Note：

Type 860 and Type F860 valves are rated for a maximum differential pressure of 1000 psi (68.95bar) when installed in the non-preferred flow direction (shaft-upstream).

Type 860 and Type F860 valves with 316 stainless steel shafts are rated for a maximum differential pressure of 1000 psi (68.95 bar)

备注：

860型和F860型阀门安装在非优先流向（阀杆上游）时，额定最大压差为1000psi (68.95bar)。含316不锈钢阀杆的860型和F860型阀门安装在任意方向，其额定最大压差为1000psi。

阀门扭矩参数Xtreme 阀座

带X阀座和阀杆下游在指定关闭压差下860W和860L系列阀门的扭矩

Xtreme 阀座

带X阀座和阀杆上游在指定关闭压差下860W和860L系列阀门的扭矩

带防火阀座或阀杆上游或下游的860W和860L系列阀门的扭矩