诺基亚5110显示屏51单片机驱动程序2
诺基亚5110显示屏51单片机驱动程序
#include
#include "intrins.h" //_nop_();延时函数用
#include
#define uchar unsigned char
#define uint unsigned int
sbit sce = P3^4; //片选
sbit res = P0^0; //复位,0复位
sbit dc = P3^5; //1写数据,0写指令
sbit sdin = P3^7; //数据
sbit sclk = P3^6; //时钟
uint data temp_data[2]={0x00,0x00}; //读出温度暂放
//================18b20数据口定义===============
sbit DQ=P0^0; //温度输入口uint h;
uint temp;
unsigned char presence,flash=0;
/*****************延时函数*************************/
void delay(uint t)
{
for (;t>0;t--);
}
//================延时函数=====================
void delay_1ms(void)//1ms延时函数
{
unsigned int i;
for (i=0;i<500;i++);
}
/*---------------lcd显示函数开始----------------
LCD_write_byte: 使用SPI接口写数据到LCD
输入参数:dt:写入的数据;
command :写数据/命令选择;
编写日期:20080918
----------------------------------------------*/
void LCD_write_byte(unsigned char dt, unsigned char command)
{
unsigned char i;
sce=0;
dc=command;
for(i=0;i<8;i++)
{
if(dt&0x80)
sdin=1;
else
sdin=0;
dt=dt<<1;
sclk=0;
sclk=1;
}
dc=1;
sce=1;
sdin=1;
}
/*---------------------------------------
LCD_init: 5110LCD初始化
编写日期:20080918
----------------------------------------- */
void LCD_init(void)
{
res=0;
delay_1ms();
res=1;
LCD_write_byte(0x21,0);//初始化Lcd,功能设定使用扩充指令LCD_write_byte(0xd0,0);//设定液晶偏置电压
LCD_write_byte(0x20,0);//使用基本指令
LCD_write_byte(0x0C,0);//设定显示模式,正常显示
}
/*-------------------------------------------
LCD_set_XY: 设置LCD坐标函数
输入参数:X:0-83 Y:0-5
编写日期:20080918
---------------------------------------------*/
void LCD_set_XY(unsigned char X, unsigned char Y)
{
LCD_write_byte(0x40 | Y, 0);// column
LCD_write_byte(0x80 | X, 0);// row
}
/*------------------------------------------
LCD_clear: LCD清屏函数
编写日期:20080918
--------------------------------------------*/
void LCD_c lear(void)
{
unsigned char t;
unsigned char k;
LCD_set_XY(0,0);
for(t=0;t<6;t++)
{
for(k=0;k<84;k++)
{
LCD_write_byte(0x00,1);
}
}
}
/*---------------------------------------------
LCD_write_shu: 显示8(宽)*16(高)点阵列数字字母符号等半角类
输入参数:c:显示的字符;
编写日期:20080918
-----------------------------------------------*/
void LCD_write_shu(unsigned char row, unsigned char page,unsigned char c) //row:列page:页dd:字符
{
unsigned char i;
LCD_set_XY(row*8, page);// 列,页
for(i=0; i<8;i++)
{
LCD_write_byte(shuzi[c*16+i],1);
}
LCD_set_XY(row*8, page+1);// 列,页
for(i=8; i<16;i++)
{
LCD_write_byte(shuzi[c*16+i],1);
}
}
/*---------------------------------------------
LCD_write_hanzi: 显示16(宽)*16(高)点阵列汉字等半角类
输入参数:c:显示的字符;
编写日期:20080918
-----------------------------------------------*/
void LCD_write_hanzi(unsigned char row, unsigned char page,unsigned char c) //row:列page:页dd:字符
{
unsigned char i;
LCD_set_XY(row*8, page);// 列,页
for(i=0; i<16;i++)
{
LCD_write_byte(hanzi[c*32+i],1);
}
LCD_set_XY(row*8, page+1);// 列,页
for(i=16; i<32;i++)
{
LCD_write_byte(hanzi[c*32+i],1);
}
}
//=================lcd显示函数结束================
//=================18b20相关函数开始==============
/****************DS18B20复位函数************************/
ow_reset(void)
{
char presence=1;
while(presence)
{
while(presence)
{
DQ=1;_nop_();_nop_(); //从高拉倒低
DQ=0;
delay(50); //550 us
DQ=1;
delay(6); //66 us
presence=DQ; //presence=0 复位成功,继续下一步}
delay(45); //延时500 us
presence=~DQ;
}
DQ=1; //拉高电平
}
//
//
/****************DS18B20写命令函数************************/ void write_byte(uchar val) //向1-WIRE 总线上写1个字节{
uchar i;
for(i=8;i>0;i--)
{
DQ=1;_nop_();_nop_(); //从高拉倒低
DQ=0;_nop_();_nop_();_nop_();_nop_(); //5 us
DQ=val&0x01; //最低位移出
delay(6); //66 us
val=val/2; //右移1位
}
DQ=1;
delay(1);
}
/****************DS18B20读1字节函数************************/ uchar read_byte(void) //从总线上取1个字节
{
uchar i;
uchar value=0;
for(i=8;i>0;i--)
{
DQ=1;_nop_();_nop_();
value>>=1;
DQ=0;_nop_();_nop_();_nop_();_nop_(); //4 us
DQ=1;_nop_();_nop_();_nop_();_nop_(); //4 us
if(DQ)value|=0x80;
delay(6); //66 us
}
DQ=1;
return(value);
}
//
/****************读出温度函数************************/
read_temp()
{
ow_reset(); //总线复位
if(presence==1)
{flash=1;} //DS18B20不正常,蜂鸣器报警delay(200);
write_byte(0xcc); //发命令
write_byte(0x44); //发转换命令
ow_reset();
delay(1);
write_byte(0xcc); //发命令
write_byte(0xbe);
temp_data[0]=read_byte(); //读温度值的第字节
temp_data[1]=read_byte(); //读温度值的高字节
temp=temp_data[1];
temp<<=8;
temp=temp|temp_data[0]; // 两字节合成一个整型变量。return temp; //返回温度值
}
//=================18b20相关函数结束==============
//=================主函数=========================
void main(void)
{
unsigned char k;
res=0;
for(k=0;k<250;k++);
res=1;
LCD_init(); //初始化LCD模块LCD_clear(); //清屏幕
LCD_write_hanzi(1,0,0); //
LCD_write_hanzi(3,0,1); //
LCD_write_hanzi(5,0,2); //
LCD_write_hanzi(7,0,3); //
LCD_write_hanzi(1,2,4); //
LCD_write_hanzi(4,2,5); //
LCD_write_hanzi(7,2,6); //
LCD_write_shu(0,4,5); // LCD_write_shu(1,4,1); //
LCD_write_shu(2,4,35); // LCD_write_shu(3,4,33); // LCD_write_shu(4,4,13); // LCD_write_shu(5,4,25); // LCD_write_shu(6,4,19); // LCD_write_shu(7,4,45); // LCD_write_shu(8,4,12); // LCD_write_shu(9,4,23); //
while(1)
{
}
}