冷水机安装注意事项(中英版)

冷水机安装注意事项（中英版）

来源：凯德利冷机

w w w . S z k a y d e l i . C o m 凯德利冷水机组安装与维护注意事项

1、机组吊运定位安装须注意安全并请切勿使机组发碰撞保证设备完整

2、机组安装场所应避风吹寸淋阳光直射或其热源直接幅射；机房环境须保持干燥、清洁并确保通风良并留便于机组保养检修空间

3、机组安装于强度须坚固水泥平台并机组底架垫防震橡胶垫校机组水平装脚螺丝

4、与机组配套使用循环水泵应参照机组所标明水流量、水阻力等数据要求选型安装

5、水泵须设置于机组进水口前水泵入口应安装滤器避免异物进入机组热交换器机组若安装于水质较差区须作水处理避免热交换器损坏

6、连接机组水管道系统须安装水流关、水压表、温度计等便于机组运转检查维护

7、避免空气滞留于水系统必须于机组水管道高点处安装排气阀或膨胀水箱

8、冷冻水管路保温应确实避免冷量散失及凝露现象产

9、系统连接管道重量由机体承受机组进水接口应须安装橡胶防震软接及阀门避免振及便于检修维护

10、机组配置电线应按耗电功率选用截面稍些相应余量电线并接驳安装靠电控件及电源接防止漏电事故发

11、由于机组杨逆相、缺相保护接线安装须注意线路相位否确错接相位及缺相机组均能运转

12、机组冬停机超2或夏停机超1须送电先加热压缩机油温再启机组运转

13、冬季外气环境温度低于0度机组间（约数）停机使水管路冻结水管路设计及施工须防机组受冻结损坏功能避免管路冻结管路水全部排除

14、机组操作管理员需随观察机组运行状况旦发现异情况请及排除故障强制运行必机组造损害

15、保修期内我公司承诺所冷水机组提供免费保用保修服务机组使用程遇排除故障请机组型号、部件名称告经销商或我公司便尽快您提供快捷修服务

警告：本机组属高电压、专业性较强机械设备应由专业技术员严格参照《使用安装说明书》进行确操作维护

Notes for the installation and Maintenance of Machine.

1. Pay more attention to the Lifting positioning installation by avoiding the crash of the machine.

2. Make sure the installation place with good ventilation, clean, under shade, dry and keep away from any heating sources. Leave enough space for the future maintenance service.

3. The machine should be installed strongly in the cement platform, put the anti-vibration rubber rail under the bottom of the machine, adjust the installation level, and fix it with bolt.

4. The circulating water pump should be chose and installed based on the technical data of main machine , like flow rate , water pressure .

5. The circulating water pump should be installed in the front of the inlet port of machine, it should add the water filter at the inlet port of water pump to avoid the impurity flow into the heat exchanger. If the machine installed in the bad water quality region, it should be first to make the purified solution for the water to avoid the damage of the heat exchanger.

6. The water pipeline, which connect with the machine should install a flow switch, water pressure, temperature gauge . These parts will be good for the future maintenance of the machine.

7. To avoid the air stay in the water system, it must install a discharge valve or expansion water tank in the highest port of the return water pipeline.

8. It should insulated for the cold water pipeline to avoid the loss of cooling capacity and condensation.

9. It can’t connect the water pipeline with system of machine directly, it should add some anti-vibration soft connector and gate valve.

10. When connect with the power source, it should chose the suitable wire based on the maximum output power of the machine, and chose the more reliable electronic components and power ground.

11. Since the machine have the anti-phase and missing phase protection. When connect the wire, pls make sure the phase connect well, If phase is wrong or missing phase, the unit can’t start to work.

12. If the unit stop to work around 2 hours in the winter and one day in the summer, it should first to connect the power to heat the compressor oil , then start the machine.

13. While the ambient working temperature in the winter under 0 deg C , If it stop to use around several days, the water pipeline may be frozen, it should do some anti-freezing solution when design and install the water pipeline. But the best way is to discharge the water fully in the pipeline if you stop the machine.

14. The operator should pay more attention on the running condition of the machine, If it found some abnormal condition, pls remove the fault on time. If it force to run, it will bring heavy damage to the machine.

15. Under warranty period, we will provide free repair service to our machine, when the customer can’t solve the problem by reading the instruction book, pls contact us with the exactly information of the machine like the model number, and parts name. Warning: The machine is the high voltage and technology strictly requested units, it should be operated and maintained by the professional technical man with perusal the Installation instruction book.