1N4470中文资料
MAX4470中文资料
General DescriptionThe MAX4464/MAX4470/MAX4471/MAX4472/MAX4474family of micropower op amps operate from a single +1.8V to +5.5V supply and draw only 750nA of supply current. The MAX4470 family feature ground-sensing inputs and Rail-to-Rail ®output. The ultra-low supply current, low-operating voltage, and rail-to-rail output capabilities make these operational amplifiers ideal for use in single lithium ion (Li+), or two-cell NiCd or alka-line battery systems.The rail-to-rail output stage of the MAX4464/MAX4470/ MAX4471/MAX4472/MAX4474 amplifiers is capable of driving the output voltage to within 4mV of the rail with a 100k Ωload, and can sink and source 11mA with a +5V supply. These amplifiers are available in both fully com-pensated and decompensated versions. The single MAX4470, dual MAX4471, and the quad MAX4472 are unity-gain stable. The single MAX4464 and the dual MAX4474 are stable for closed-loop gain configurations of ≥+5V/V. These amplifiers are available in space-sav-ing SC70, SOT23, µMAX, and TSSOP packages.ApplicationsFeatureso Ultra-Low 750nA Supply Current Per Amplifier o Ultra-Low +1.8V Supply Voltage Operation o Ground-Sensing Input Common-Mode Range o Outputs Swing Rail-to-Railo Outputs Source and Sink 11mA of Load Current o No Phase Reversal for Overdriven Inputs o High 120dB Open-Loop Voltage Gain o Low 500µV Input Offset Voltage o 9kHz Gain-Bandwidth Product (MAX4470/MAX4471/MAX4472)o 40kHz Gain-Bandwidth Product (MAX4464/MAX4474)o 250pF (min) Capacitive Load Capability o Available in Tiny 5-Pin SC70 and 8-Pin SOT23PackagesMAX4464/MAX4470/MAX4471/MAX4472/MAX4474Single/Dual/Quad, +1.8V/750nA, SC70,Rail-to-Rail Op Amps________________________________________________________________Maxim Integrated Products 1Pin Configurations19-2021; Rev 2; 2/03For pricing, delivery, and ordering information,please contact Maxim/Dallas Direct!at 1-888-629-4642, or visit Maxim’s website at .Ordering InformationRail-to-Rail is a registered trademark of Nippon Motorola, Ltd.Selector GuideBattery-Powered SystemsPortable Instrumentation Pagers and Cellphones Micropower ThermostatsElectrometer Amplifiers Solar-Powered Systems Remote Sensor Active Badges pH MetersM A X 4464/M A X 4470/M A X 4471/M A X 4472/M A X 4474Single/Dual/Quad, +1.8V/750nA, SC70, Rail-to-Rail Op Amps 2_______________________________________________________________________________________ABSOLUTE MAXIMUM RATINGSELECTRICAL CHARACTERISTICSStresses beyond those listed under “Absolute Maximum Ratings” may cause permanent damage to the device. These are stress ratings only, and functional operation of the device at these or any other conditions beyond those indicated in the operational sections of the specifications is not implied. Exposure to absolute maximum rating conditions for extended periods may affect device reliability.V DD to V SS ...............................................................-0.3V to +6V IN_+ or IN_-......................................(V SS - 0.3V) to (V DD + 0.3V)OUT_ Shorted to V SS or V DD ......................................Continuous Continuous Power Dissipation (T A = +70°C)5-Pin SC70 (derate 3.1mW/°C above +70°C)...................247mW 5-Pin SOT23 (derate 7.1mW/°C above +70°C).................571mW 8-Pin SOT23 (derate 8.9mW/°C above +70°C).................714mW 8-Pin µMAX (derate 4.5mW/°C above +70°C)..................362mW8-Pin SO (derate 5.88mW/°C above +70°C)....................471mW 14-Pin TSSOP (derate 9.1mW/°C above +70°C)...........727mW 14-Pin SO (derate 8.33mW/°C above +70°C)...............667mW Operating Temperature Range .........................-40°C to +85°C Junction Temperature .....................................................+150°C Storage Temperature Range.............................-65°C to +150°C Lead Temperature (soldering, 10s) ................................+300°CMAX4464/MAX4470/MAX4471/MAX4472/MAX4474Single/Dual/Quad, +1.8V/750nA, SC70,Rail-to-Rail Op Amps_______________________________________________________________________________________3ELECTRICAL CHARACTERISTICS (continued)ELECTRICAL CHARACTERISTICSM A X 4464/M A X 4470/M A X 4471/M A X 4472/M A X 4474Single/Dual/Quad, +1.8V/750nA, SC70, Rail-to-Rail Op Amps 4_______________________________________________________________________________________Typical Operating Characteristics(V DD = +5V, V SS = 0, V CM = 0, R L = 100k Ωto V DD /2, T A = +25°C, unless otherwise noted.)0.20.10.50.40.30.70.80.60.91.5 3.0 3.52.0 2.5 4.0 4.5 5.0 5.5 6.0SUPPLY CURRENT PER AMPLIFIER vs.SUPPLY VOLTAGEM A X 4470–74 t o c 01SUPPLY VOLTAGE (V)S U P P L Y C U R R E N T (µA )0.20.10.50.40.30.70.80.60.9-500-25255075100SUPPLY CURRENT PER AMPLIFIER vs.TEMPERATUREM A X 4470–74 t o c 02TEMPERATURE (°C)S U P P L Y C U R R E N T (µA )00.100.050.300.200.250.150.400.450.350.50-50-25255075100OFFSET VOLTAGE vs.TEMPERATUREM A X 4470–74 t o c 03TEMPERATURE (°C)O F F S E T V O L T A G E (m V )00.100.050.200.150.300.250.350.450.400.501.01.50.52.02.53.03.54.0OFFSET VOLTAGEvs. COMMON-MODE VOLTAGEM A X 4470-74 t o c 04COMMON-MODE VOLTAGE (V)O F F S E T V O L T A G E (m V )-400-350-150-250-200-300-50-1000-50-25255075100INPUT BIAS CURRENT vs.TEMPERATUREM A X 4470–74 t o c 05TEMPERATURE (°C)I N P U T B I A S C U R R E N T (p A )-90-70-80-40-50-60-20-10-3000 1.51.00.5 2.0 2.5 3.0 3.5 4.0INPUT BIAS CURRENT MON-MODE VOLTAGEM A X 4470–74 t o c 06COMMON-MODE VOLTAGE (V)I N P U T B I A S C U R R E N T (p A )0-1001010010k1kPOWER-SUPPLY REJECTION RATIO vs.FREQUENCY-80-90M A X 4470–74 t o c 07FREQUENCY (Hz)P S R R (d B )-60-70-40-30-50-20-1000.21.00.60.80.41.41.21.6-50-25255075100OUTPUT VOLTAGE SWING LOW vs.TEMPERATURETEMPERATURE (°C)V O L - V S S (m V )142356-500-25255075100OUTPUT VOLTAGE SWING HIGH vs.TEMPERATURETEMPERATURE (°C)V D D - V O H (m V )MAX4464/MAX4470/MAX4471/MAX4472/MAX4474Single/Dual/Quad, +1.8V/750nA, SC70,Rail-to-Rail Op Amps_______________________________________________________________________________________5-120-100-110-60-80-70-90-40-30-50-20-50-25255075100COMMON-MODE REJECTION RATIO vs.TEMPERATURETEMPERATURE (°C)C M R R (d B )00.40.20.80.61.21.01.4-5025-255075100MINIMUM SUPPLY VOLTAGEvs. TEMPERATUREM A X 4470-74 t o c 11TEMPERATURE (°C)M I N I M UM S U P P L Y V O L T A G E (V )607080901001101201301402.53.0 3.54.0 4.55.0A VOL vs. OUTPUT VOLTAGE SWINGOUTPUT VOLTAGE (Vp-p)A V O L (dB )11001k 10k10100kMAX4470/MAX4471/MAX4472GAIN AND PHASE vs. FREQUENCYFREQUENCY (Hz)G A I N (d B )P H A S E (d e g )80706050403020-60100-10-20-30-40-509045-1350-45-9011001k10k10100kMAX4470/MAX4471/MAX4472GAIN AND PHASE vs. FREQUENCYFREQUENCY (Hz)G A I N (d B )P H A S E (d e g )80706050403020-60100-10-20-30-40-501801359045-1350-45-90-40-140101001k 10k100kCROSSTALK vs. FREQUENCY-100-120FREQUENCY (Hz)C R O S S T A L K (d B )-80-6010.000.011010010k1kMAX4470/MAX4471/MAX4472TOTAL HARMONIC DISTORTION PLUS NOISE vs. FREQUENCYM A X 4470–74 t o c 16FREQUENCY (Hz)T H D + N (%)0.101.0010k 10101k 100100k10kVOLTAGE NOISE DENSITY vs.FREQUENCYM A X 4470–74 t o c 17FREQUENCY (Hz)1001k N O I S E (n V /√H z )100k10010k100k 1MMAX4470/MAX4471/MAX4472 STABILITY vs. CAPACITIVE AND RESISTIVE LOADSRESISTIVE LOAD (Ω)1k10kC A P A C I T I V E L O AD (p F )Typical Operating Characteristics (continued)(V DD = +5V, V SS = 0, V CM = 0, R L = 100k Ωto V DD /2, T A = +25°C, unless otherwise noted.)500µs/divMAX4470/MAX4471/MAX4472SMALL-SIGNAL STEP RESPONSEINPUT 50mV/divOUTPUT 50mV/divV DD = +5V A V = +1V/V R L = 1M Ω C L = 250pF500µs/div MAX4470/MAX4471/MAX4472SMALL-SIGNAL STEP RESPONSEINPUT 50mV/divOUTPUT 50mV/div V DD = +5V A V = +1V/V R L = 1M Ω C L = 1000pF500µs/div MAX4470/MAX4471/MAX4472LARGE-SIGNAL STEP RESPONSEV DD = +5V A V = +1V/V R L = 1M ΩC L = 12pFINPUT 500mV/divOUTPUT 500mV/div500µs/divMAX4470/MAX4471/MAX4472LARGE-SIGNAL STEP RESPONSEINPUT 500mV/divOUTPUT 500mV/divV DD = +5V A V = +1V/V R L = 1M Ω C L = 1000pF052010152530010050150200250300MAX4470/MAX4471/MAX4472PERCENT OVERSHOOT vs. CAPACITIVE LOADC LOAD (pF)P E R C E N T O V E R S H O O T (%)3-71001k 10kMAX4470/MAX4471/MAX4472SMALL-SIGNAL GAIN vs. FREQUENCY-5-6FREQUENCY (Hz)G A I N (d B )-3-4-10-2123-71001k 100k10k MAX4470/MAX4471/MAX4472SMALL-SIGNAL GAIN vs. FREQUENCY-5-6FREQUENCY (Hz)G A I N (d B )-3-4-10-212M A X 4464/M A X 4470/M A X 4471/M A X 4472/M A X 4474Single/Dual/Quad, +1.8V/750nA, SC70, Rail-to-Rail Op Amps 6_______________________________________________________________________________________0128416202428323640021345I OUT vs. V OUTV OUT (V)I O U T (m A )500µs/div MAX4470/MAX4471/MAX4472SMALL-SIGNAL STEP RESPONSE V DD = +5V A V = +1V/V R L = 1M ΩC L = 12pFINPUT 500mV/divOUTPUT 500mV/div Typical Operating Characteristics (continued)(V DD = +5V, V SS = 0, V CM = 0, R L = 100k Ωto V DD /2, T A = +25°C, unless otherwise noted.)MAX4464/MAX4470/MAX4471/MAX4472/MAX4474Single/Dual/Quad, +1.8V/750nA, SC70,Rail-to-Rail Op Amps_______________________________________________________________________________________7Typical Operating Characteristics (continued)(V DD = +5V, V SS = 0, V CM = 0, R L = 100k Ωto V DD /2, T A = +25°C, unless otherwise noted.)3-71001k 10k 100k MAX4470/MAX4471/MAX4472SMALL-SIGNAL GAIN vs. FREQUENCY-5FREQUENCY (Hz)G A I N (d B )-3-112-6-4-203-71001k 10k MAX4470/MAX4471/MAX4472LARGE-SIGNAL GAIN vs. FREQUENCY-5-6FREQUENCY (Hz)G A I N (d B )-3-4-10-2123-71001k 10kMAX4470/MAX4471/MAX4472LARGE-SIGNAL GAIN vs. FREQUENCY-5-6FREQUENCY (Hz)G A I N (d B )-3-4-10-2123-71001k 10kMAX4470/MAX4471/MAX4472LARGE-SIGNAL GAIN vs. FREQUENCY-5-6FREQUENCY (Hz)G A I N (d B )-3-4-10-21280-6011k 10k100k10FREQUENCY (Hz)G A I N (d B )10100MAX4464/MAX4474GAIN AND PHASE vs. FREQUENCY7060504030200-10-20-30-40-5018013590450-45-90-135P H A S E (d e g r e e s )80-6011k 10k100k10FREQUENCY (Hz)G A I N (d B )10100MAX4464/MAX4474GAIN AND PHASE vs. FREQUENCY7060504030200-10-20-30-40-5018013590450-45-90-135P H A S E (d e g r e e s )0.0011010k1k100MAX4464/MAX4474TOTAL HARMONIC DISTORTION PLUS NOISE vs. FREQUENCY100.0110.1M A X 4464 t o c 34FREQUENCY (Hz)T H D + N (%)100,00010010k100k 1MMAX4464/MAX4474STABILITY vs. CAPACITIVE AND RESISTIVE LOADSRESISTIVE LOAD (Ω)C A P A C I T I V E L O AD (p F )100010,000OUTPUT 50mV/divINPUT 10mV/divMAX4464/MAX4474SMALL-SIGNAL STEP RESPONSE500µs/divV DD = +5V A V = +5V/V R L = 1M ΩC L = 8pFM A X 4464/M A X 4470/M A X 4471/M A X 4472/M A X 4474Single/Dual/Quad, +1.8V/750nA, SC70, Rail-to-Rail Op Amps 8_______________________________________________________________________________________OUTPUT 50mV/div INPUT 10mV/divMAX4464/MAX4474SMALL-SIGNAL STEP RESPONSEM A X 4464 t o c 37500µs/div V DD = +5V A V = +5V/V R L = 1M ΩC L = 250pFOUTPUT 50mV/div INPUT 10mV/divMAX4464/MAX4474SMALL-SIGNAL STEP RESPONSEM A X 4464 t o c 38500µs/div V DD = +5V A V = +5V/V R L = 1M ΩC L = 1000pFOUTPUT 500mV/divINPUT 100mV/divMAX4464/MAX4474LARGE-SIGNAL STEP RESPONSE500µs/divV DD = +5V A V = +5V/V R L = 1M ΩC L = 8pFOUTPUT 500mV/divINPUT 100mV/divMAX4464/MAX4474LARGE-SIGNAL STEP RESPONSE500µs/divV DD = +5V A V = +5V/V R L = 1M ΩC L = 1000pF10520152530010015050200250300MAX4464/MAX4474PERCENT OVERSHOOT vs. CAPACITIVE LOADC LOAD (pF)P E R C E N T O V E R S H O O T (%)2-7100100k10k 1k MAX4464/MAX4474SMALL-SIGNAL NORMALIZED GAINvs. FREQUENCY-4-60-23-3-51-1FREQUENCY (Hz)G A I N (d B )2-7100100k10k1kMAX4464/MAX4474SMALL-SIGNAL NORMALIZED GAINvs. FREQUENCY-4-60-23-3-51-1FREQUENCY (Hz)G A I N (d B )Typical Operating Characteristics (continued)(V DD = +5V, V SS = 0, V CM = 0, R L = 100k Ωto V DD /2, T A = +25°C, unless otherwise noted.)MAX4464/MAX4470/MAX4471/MAX4472/MAX4474Single/Dual/Quad, +1.8V/750nA, SC70,Rail-to-Rail Op Amps2-7100100k 10k 1k MAX4464/MAX4474LARGE-SIGNAL NORMALIZED GAINvs. FREQUENCY-4-60-23-3-51-1FREQUENCY (Hz)G A I N (d B )2-7100100k10k 1k MAX4464/MAX4474LARGE-SIGNAL NORMALIZED GAINvs. FREQUENCY-4-60-23-3-51-1FREQUENCY (Hz)G A I N (d B )2-7100100k 10k 1k MAX4464/MAX4474SMALL-SIGNAL NORMALIZED GAINvs. FREQUENCY-4-60-23-3-51-1FREQUENCY (Hz)G A I N (d B )2-7100100k10k 1k MAX4464/MAX4474LARGE-SIGNAL NORMALIZED GAINvs. FREQUENCY-4-60-23-3-51-1FREQUENCY (Hz)G A I N (d B )Typical Operating Characteristics (continued)(V DD = +5V, V SS = 0, V CM = 0, R L = 100k Ωto V DD /2, T A = +25°C, unless otherwise noted.)M A X 4464/M A X 4470/M A X 4471/M A X 4472/M A X 4474Single/Dual/Quad, +1.8V/750nA, SC70, Rail-to-Rail Op Amps 10______________________________________________________________________________________Figure 2. Compensation for Feedback Node CapacitanceApplications InformationGround SensingThe common-mode input range of the MAX4470 family extends down to ground, and offers excellent common-mode rejection. These devices are guaranteed not to undergo phase reversal when the input is overdriven.Power Supplies and LayoutThe MAX4470 family operates from a single +1.8V to +5.5V power supply. Bypass power supplies with a 0.1µF ceramic capacitor placed close to the V DD pin. Ground layout improves performance by decreasing the amount of stray capacitance and noise at the op amp ’s inputs and outputs. To decrease stray capacitance, mini-mize PC board lengths and resistor leads, and place external components close to the op amps ’ pins.BandwidthThe MAX4470/MAX4471/MAX4472 are internally compensated for unity-gain stability and have a typical gain-bandwidth of 9kHz. The MAX4464/MAX4474 have a 40kHz typical gain-bandwidth and are stable for a gain of +5V/V or greater.StabilityThe MAX4464/MAX4470/MAX4471/MAX4472/MAX4474maintain stability in their minimum gain configuration while driving capacitive loads. Although this product family is primarily designed for low-frequency applica-tions, good layout is extremely important because low-power requirements demand high-impedance circuits.The layout should also minimize stray capacitance at the amplifier inputs. However some stray capacitance may be unavoidable, and it may be necessary to add a 2pF to 10pF capacitor across the feedback resistor as shown in Figure 2. Select the smallest capacitor value that ensures stability.Chip InformationMAX4470/MAX4464 TRANSISTOR COUNT: 147MAX4471/MAX4474 TRANSISTOR COUNT: 293MAX4472 TRANSISTOR COUNT: 585PROCESS: BiCMOSMAX4464/MAX4470/MAX4471/MAX4472/MAX4474Rail-to-Rail Op Amps______________________________________________________________________________________11M A X 4464/M A X 4470/M A X 4471/M A X 4472/M A X 4474Rail-to-Rail Op AmpsS C 70, 5L .E P SPackage Information(The package drawing(s) in this data sheet may not reflect the most current specifications. For the latest package outline information,go to /packages .MAX4464/MAX4470/MAX4471/MAX4472/MAX4474Rail-to-Rail Op AmpsPackage Information (continued)(The package drawing(s) in this data sheet may not reflect the most current specifications. For the latest package outline information,go to /packages .M A X 4464/M A X 4470/M A X 4471/M A X 4472/M A X 4474Rail-to-Rail Op Amps Maxim cannot assume responsibility for use of any circuitry other than circuitry entirely embodied in a Maxim product. No circuit patent licenses areimplied. Maxim reserves the right to change the circuitry and specifications without notice at any time.14____________________Maxim Integrated Products, 120 San Gabriel Drive, Sunnyvale, CA 94086 408-737-7600©2003 Maxim Integrated ProductsPrinted USAis a registered trademark of Maxim Integrated Products.S O I C N .E P SPackage Information (continued)(The package drawing(s) in this data sheet may not reflect the most current specifications. For the latest package outline information,go to /packages .。
BC447;BC447G;BC449;BC449A;BC449AG;中文规格书,Datasheet资料
100 70 50
−5.0 V VCE = −1.0 V
30 −1.0
−2.0 −3.0 −5.0 −7.0 −10 −20 −30 −50 −70 −100 IC, COLLECTOR CURRENT (mA)
Figure 1. Current−Gain — Bandwidth Product
Figure 3. Switching Times
IC , COLLECTOR CURRENT (mA)
−1.0 k −700 −500
−300 −200
−100 −70 −50
−30 −20
−10 −1.0
CURRENT LIMIT
THERMAL LIMIT
SECOND BREAKDOWN LIMIT
VCEO
Vdc
80
100
Collector-Base Voltage BC447 BC449, BC449A
VCBO
Vdc
80
100
Emitter-Base Voltage
Collector Current − Continuous
Total Device Dissipation @ TA = 25°C Derate above 25°C
IC =
IC =
100 mA 200 mA
0.8
0.4
TJ = 25°C
0 0.02 0.05 0.1
0.2 0.5 1.0 2.0 IB, BASE CURRENT (mA)
5.0 10 20
Figure 7. Collector Saturation Region
RqVB , TEMPERATURE COEFFICIENT (mV/° C)
SN74LS674DWG4中文资料
Copyright © 1988, Texas Instruments Incorporated PRODUCTION DATA information is current as of publication date.Products conform to specifications per the terms of Texas Instrumentsstandard warranty. Production processing does not necessarily includetesting of all parameters.POST OFFICE BOX 655303 • DALLAS, TEXAS 752652POST OFFICE BOX 655303 • DALLAS, TEXAS 752653 POST OFFICE BOX 655303 • DALLAS, TEXAS 752654POST OFFICE BOX 655303 • DALLAS, TEXAS 752655 POST OFFICE BOX 655303 • DALLAS, TEXAS 752656POST OFFICE BOX 655303 • DALLAS, TEXAS 75265IMPORTANT NOTICETexas Instruments Incorporated and its subsidiaries(TI)reserve the right to make corrections,modifications,enhancements, improvements,and other changes to its products and services at any time and to discontinue any product or service without notice. Customers should obtain the latest relevant information before placing orders and should verify that such information is current and complete.All products are sold subject to TI’s terms and conditions of sale supplied at the time of order acknowledgment.TI warrants performance of its hardware products to the specifications applicable at the time of sale in accordance with TI’s standard warranty.Testing and other quality control techniques are used to the extent TI deems necessary to support this warranty.Except where mandated by government requirements,testing of all parameters of each product is not necessarily performed.TI assumes no liability for applications assistance or customer product design.Customers are responsible for their products and applications using TI components.To minimize the risks associated with customer products and applications,customers should provide adequate design and operating safeguards.TI does not warrant or represent that any license,either express or implied,is granted under any TI patent right,copyright,mask work right,or other TI intellectual property right relating to any combination,machine,or process in which TI products or services are rmation published by TI regarding third-party products or services does not constitute a license from TI to use such products or services or a warranty or endorsement e of such information may require a license from a third party under the patents or other intellectual property of the third party,or a license from TI under the patents or other intellectual property of TI. Reproduction of information in TI data books or data sheets is permissible only if reproduction is without alteration and is accompanied by all associated warranties,conditions,limitations,and notices.Reproduction of this information with alteration is an unfair and deceptive business practice.TI is not responsible or liable for such altered documentation.Resale of TI products or services with statements different from or beyond the parameters stated by TI for that product or service voids all express and any implied warranties for the associated TI product or service and is an unfair and deceptive business practice.TI is not responsible or liable for any such statements.TI products are not authorized for use in safety-critical applications(such as life support)where a failure of the TI product would reasonably be expected to cause severe personal injury or death,unless officers of the parties have executed an agreement specifically governing such use.Buyers represent that they have all necessary expertise in the safety and regulatory ramifications of their applications,and acknowledge and agree that they are solely responsible for all legal,regulatory and safety-related requirements concerning their products and any use of TI products in such safety-critical applications,notwithstanding any applications-related information or support that may be provided by TI.Further,Buyers must fully indemnify TI and its representatives against any damages arising out of the use of TI products in such safety-critical applications.TI products are neither designed nor intended for use in military/aerospace applications or environments unless the TI products are specifically designated by TI as military-grade or"enhanced plastic."Only products designated by TI as military-grade meet military specifications.Buyers acknowledge and agree that any such use of TI products which TI has not designated as military-grade is solely at the Buyer's risk,and that they are solely responsible for compliance with all legal and regulatory requirements in connection with such use.TI products are neither designed nor intended for use in automotive applications or environments unless the specific TI products are designated by TI as compliant with ISO/TS16949requirements.Buyers acknowledge and agree that,if they use anynon-designated products in automotive applications,TI will not be responsible for any failure to meet such requirements. Following are URLs where you can obtain information on other Texas Instruments products and application solutions:Products ApplicationsAmplifiers Audio /audioData Converters Automotive /automotiveDSP Broadband /broadbandInterface Digital Control /digitalcontrolLogic Military /militaryPower Mgmt Optical Networking /opticalnetworkMicrocontrollers Security /securityLow Power /lpw Telephony /telephonyWirelessVideo&Imaging /videoWireless /wirelessMailing Address:Texas Instruments,Post Office Box655303,Dallas,Texas75265Copyright©2007,Texas Instruments IncorporatedIMPORTANT NOTICETexas Instruments Incorporated and its subsidiaries(TI)reserve the right to make corrections,modifications,enhancements, improvements,and other changes to its products and services at any time and to discontinue any product or service without notice. Customers should obtain the latest relevant information before placing orders and should verify that such information is current and complete.All products are sold subject to TI’s terms and conditions of sale supplied at the time of order acknowledgment.TI warrants performance of its hardware products to the specifications applicable at the time of sale in accordance with TI’s standard warranty.Testing and other quality control techniques are used to the extent TI deems necessary to support this warranty.Except where mandated by government requirements,testing of all parameters of each product is not necessarily performed.TI assumes no liability for applications assistance or customer product design.Customers are responsible for their products and applications using TI components.To minimize the risks associated with customer products and applications,customers should provide adequate design and operating safeguards.TI does not warrant or represent that any license,either express or implied,is granted under any TI patent right,copyright,mask work right,or other TI intellectual property right relating to any combination,machine,or process in which TI products or services are rmation published by TI regarding third-party products or services does not constitute a license from TI to use such products or services or a warranty or endorsement e of such information may require a license from a third party under the patents or other intellectual property of the third party,or a license from TI under the patents or other intellectual property of TI. Reproduction of information in TI data books or data sheets is permissible only if reproduction is without alteration and is accompanied by all associated warranties,conditions,limitations,and notices.Reproduction of this information with alteration is an unfair and deceptive business practice.TI is not responsible or liable for such altered documentation.Resale of TI products or services with statements different from or beyond the parameters stated by TI for that product or service voids all express and any implied warranties for the associated TI product or service and is an unfair and deceptive business practice.TI is not responsible or liable for any such statements.TI products are not authorized for use in safety-critical applications(such as life support)where a failure of the TI product would reasonably be expected to cause severe personal injury or death,unless officers of the parties have executed an agreement specifically governing such use.Buyers represent that they have all necessary expertise in the safety and regulatory ramifications of their applications,and acknowledge and agree that they are solely responsible for all legal,regulatory and safety-related requirements concerning their products and any use of TI products in such safety-critical applications,notwithstanding any applications-related information or support that may be provided by TI.Further,Buyers must fully indemnify TI and its representatives against any damages arising out of the use of TI products in such safety-critical applications.TI products are neither designed nor intended for use in military/aerospace applications or environments unless the TI products are specifically designated by TI as military-grade or"enhanced plastic."Only products designated by TI as military-grade meet military specifications.Buyers acknowledge and agree that any such use of TI products which TI has not designated as military-grade is solely at the Buyer's risk,and that they are solely responsible for compliance with all legal and regulatory requirements in connection with such use.TI products are neither designed nor intended for use in automotive applications or environments unless the specific TI products are designated by TI as compliant with ISO/TS16949requirements.Buyers acknowledge and agree that,if they use anynon-designated products in automotive applications,TI will not be responsible for any failure to meet such requirements. Following are URLs where you can obtain information on other Texas Instruments products and application solutions:Products ApplicationsAmplifiers Audio /audioData Converters Automotive /automotiveDSP Broadband /broadbandInterface Digital Control /digitalcontrolLogic Military /militaryPower Mgmt Optical Networking /opticalnetworkMicrocontrollers Security /securityLow Power /lpw Telephony /telephonyWirelessVideo&Imaging /videoWireless /wirelessMailing Address:Texas Instruments,Post Office Box655303,Dallas,Texas75265Copyright©2007,Texas Instruments IncorporatedIMPORTANT NOTICETexas Instruments Incorporated and its subsidiaries(TI)reserve the right to make corrections,modifications,enhancements, improvements,and other changes to its products and services at any time and to discontinue any product or service without notice. Customers should obtain the latest relevant information before placing orders and should verify that such information is current and complete.All products are sold subject to TI’s terms and conditions of sale supplied at the time of order acknowledgment.TI warrants performance of its hardware products to the specifications applicable at the time of sale in accordance with TI’s standard warranty.Testing and other quality control techniques are used to the extent TI deems necessary to support this warranty.Except where mandated by government requirements,testing of all parameters of each product is not necessarily performed.TI assumes no liability for applications assistance or customer product design.Customers are responsible for their products and applications using TI components.To minimize the risks associated with customer products and applications,customers should provide adequate design and operating safeguards.TI does not warrant or represent that any license,either express or implied,is granted under any TI patent right,copyright,mask work right,or other TI intellectual property right relating to any combination,machine,or process in which TI products or services are rmation published by TI regarding third-party products or services does not constitute a license from TI to use such products or services or a warranty or endorsement e of such information may require a license from a third party under the patents or other intellectual property of the third party,or a license from TI under the patents or other intellectual property of TI. Reproduction of information in TI data books or data sheets is permissible only if reproduction is without alteration and is accompanied by all associated warranties,conditions,limitations,and notices.Reproduction of this information with alteration is an unfair and deceptive business practice.TI is not responsible or liable for such altered documentation.Resale of TI products or services with statements different from or beyond the parameters stated by TI for that product or service voids all express and any implied warranties for the associated TI product or service and is an unfair and deceptive business practice.TI is not responsible or liable for any such statements.TI products are not authorized for use in safety-critical applications(such as life support)where a failure of the TI product would reasonably be expected to cause severe personal injury or death,unless officers of the parties have executed an agreement specifically governing such use.Buyers represent that they have all necessary expertise in the safety and regulatory ramifications of their applications,and acknowledge and agree that they are solely responsible for all legal,regulatory and safety-related requirements concerning their products and any use of TI products in such safety-critical applications,notwithstanding any applications-related information or support that may be provided by TI.Further,Buyers must fully indemnify TI and its representatives against any damages arising out of the use of TI products in such safety-critical applications.TI products are neither designed nor intended for use in military/aerospace applications or environments unless the TI products are specifically designated by TI as military-grade or"enhanced plastic."Only products designated by TI as military-grade meet military specifications.Buyers acknowledge and agree that any such use of TI products which TI has not designated as military-grade is solely at the Buyer's risk,and that they are solely responsible for compliance with all legal and regulatory requirements in connection with such use.TI products are neither designed nor intended for use in automotive applications or environments unless the specific TI products are designated by TI as compliant with ISO/TS16949requirements.Buyers acknowledge and agree that,if they use anynon-designated products in automotive applications,TI will not be responsible for any failure to meet such requirements. Following are URLs where you can obtain information on other Texas Instruments products and application solutions:Products ApplicationsAmplifiers Audio /audioData Converters Automotive /automotiveDSP Broadband /broadbandInterface Digital Control /digitalcontrolLogic Military /militaryPower Mgmt Optical Networking /opticalnetworkMicrocontrollers Security /securityLow Power /lpw Telephony /telephonyWirelessVideo&Imaging /videoWireless /wirelessMailing Address:Texas Instruments,Post Office Box655303,Dallas,Texas75265Copyright©2007,Texas Instruments IncorporatedIMPORTANT NOTICETexas Instruments Incorporated and its subsidiaries(TI)reserve the right to make corrections,modifications,enhancements, improvements,and other changes to its products and services at any time and to discontinue any product or service without notice. Customers should obtain the latest relevant information before placing orders and should verify that such information is current and complete.All products are sold subject to TI’s terms and conditions of sale supplied at the time of order acknowledgment.TI warrants performance of its hardware products to the specifications applicable at the time of sale in accordance with TI’s standard warranty.Testing and other quality control techniques are used to the extent TI deems necessary to support this warranty.Except where mandated by government requirements,testing of all parameters of each product is not necessarily performed.TI assumes no liability for applications assistance or customer product design.Customers are responsible for their products and applications using TI components.To minimize the risks associated with customer products and applications,customers should provide adequate design and operating safeguards.TI does not warrant or represent that any license,either express or implied,is granted under any TI patent right,copyright,mask work right,or other TI intellectual property right relating to any combination,machine,or process in which TI products or services are rmation published by TI regarding third-party products or services does not constitute a license from TI to use such products or services or a warranty or endorsement e of such information may require a license from a third party under the patents or other intellectual property of the third party,or a license from TI under the patents or other intellectual property of TI. Reproduction of information in TI data books or data sheets is permissible only if reproduction is without alteration and is accompanied by all associated warranties,conditions,limitations,and notices.Reproduction of this information with alteration is an unfair and deceptive business practice.TI is not responsible or liable for such altered documentation.Resale of TI products or services with statements different from or beyond the parameters stated by TI for that product or service voids all express and any implied warranties for the associated TI product or service and is an unfair and deceptive business practice.TI is not responsible or liable for any such statements.TI products are not authorized for use in safety-critical applications(such as life support)where a failure of the TI product would reasonably be expected to cause severe personal injury or death,unless officers of the parties have executed an agreement specifically governing such use.Buyers represent that they have all necessary expertise in the safety and regulatory ramifications of their applications,and acknowledge and agree that they are solely responsible for all legal,regulatory and safety-related requirements concerning their products and any use of TI products in such safety-critical applications,notwithstanding any applications-related information or support that may be provided by TI.Further,Buyers must fully indemnify TI and its representatives against any damages arising out of the use of TI products in such safety-critical applications.TI products are neither designed nor intended for use in military/aerospace applications or environments unless the TI products are specifically designated by TI as military-grade or"enhanced plastic."Only products designated by TI as military-grade meet military specifications.Buyers acknowledge and agree that any such use of TI products which TI has not designated as military-grade is solely at the Buyer's risk,and that they are solely responsible for compliance with all legal and regulatory requirements in connection with such use.TI products are neither designed nor intended for use in automotive applications or environments unless the specific TI products are designated by TI as compliant with ISO/TS16949requirements.Buyers acknowledge and agree that,if they use anynon-designated products in automotive applications,TI will not be responsible for any failure to meet such requirements. Following are URLs where you can obtain information on other Texas Instruments products and application solutions:Products ApplicationsAmplifiers Audio /audioData Converters Automotive /automotiveDSP Broadband /broadbandInterface Digital Control /digitalcontrolLogic Military /militaryPower Mgmt Optical Networking /opticalnetworkMicrocontrollers Security /securityLow Power /lpw Telephony /telephonyWirelessVideo&Imaging /videoWireless /wirelessMailing Address:Texas Instruments,Post Office Box655303,Dallas,Texas75265Copyright©2007,Texas Instruments IncorporatedIMPORTANT NOTICETexas Instruments Incorporated and its subsidiaries(TI)reserve the right to make corrections,modifications,enhancements, improvements,and other changes to its products and services at any time and to discontinue any product or service without notice. Customers should obtain the latest relevant information before placing orders and should verify that such information is current and complete.All products are sold subject to TI’s terms and conditions of sale supplied at the time of order acknowledgment.TI warrants performance of its hardware products to the specifications applicable at the time of sale in accordance with TI’s standard warranty.Testing and other quality control techniques are used to the extent TI deems necessary to support this warranty.Except where mandated by government requirements,testing of all parameters of each product is not necessarily performed.TI assumes no liability for applications assistance or customer product design.Customers are responsible for their products and applications using TI components.To minimize the risks associated with customer products and applications,customers should provide adequate design and operating safeguards.TI does not warrant or represent that any license,either express or implied,is granted under any TI patent right,copyright,mask work right,or other TI intellectual property right relating to any combination,machine,or process in which TI products or services are rmation published by TI regarding third-party products or services does not constitute a license from TI to use such products or services or a warranty or endorsement e of such information may require a license from a third party under the patents or other intellectual property of the third party,or a license from TI under the patents or other intellectual property of TI. Reproduction of information in TI data books or data sheets is permissible only if reproduction is without alteration and is accompanied by all associated warranties,conditions,limitations,and notices.Reproduction of this information with alteration is an unfair and deceptive business practice.TI is not responsible or liable for such altered documentation.Resale of TI products or services with statements different from or beyond the parameters stated by TI for that product or service voids all express and any implied warranties for the associated TI product or service and is an unfair and deceptive business practice.TI is not responsible or liable for any such statements.TI products are not authorized for use in safety-critical applications(such as life support)where a failure of the TI product would reasonably be expected to cause severe personal injury or death,unless officers of the parties have executed an agreement specifically governing such use.Buyers represent that they have all necessary expertise in the safety and regulatory ramifications of their applications,and acknowledge and agree that they are solely responsible for all legal,regulatory and safety-related requirements concerning their products and any use of TI products in such safety-critical applications,notwithstanding any applications-related information or support that may be provided by TI.Further,Buyers must fully indemnify TI and its representatives against any damages arising out of the use of TI products in such safety-critical applications.TI products are neither designed nor intended for use in military/aerospace applications or environments unless the TI products are specifically designated by TI as military-grade or"enhanced plastic."Only products designated by TI as military-grade meet military specifications.Buyers acknowledge and agree that any such use of TI products which TI has not designated as military-grade is solely at the Buyer's risk,and that they are solely responsible for compliance with all legal and regulatory requirements in connection with such use.TI products are neither designed nor intended for use in automotive applications or environments unless the specific TI products are designated by TI as compliant with ISO/TS16949requirements.Buyers acknowledge and agree that,if they use anynon-designated products in automotive applications,TI will not be responsible for any failure to meet such requirements. Following are URLs where you can obtain information on other Texas Instruments products and application solutions:Products ApplicationsAmplifiers Audio /audioData Converters Automotive /automotiveDSP Broadband /broadbandInterface Digital Control /digitalcontrolLogic Military /militaryPower Mgmt Optical Networking /opticalnetworkMicrocontrollers Security /securityLow Power /lpw Telephony /telephonyWirelessVideo&Imaging /videoWireless /wirelessMailing Address:Texas Instruments,Post Office Box655303,Dallas,Texas75265Copyright©2007,Texas Instruments IncorporatedIMPORTANT NOTICETexas Instruments Incorporated and its subsidiaries(TI)reserve the right to make corrections,modifications,enhancements, improvements,and other changes to its products and services at any time and to discontinue any product or service without notice. Customers should obtain the latest relevant information before placing orders and should verify that such information is current and complete.All products are sold subject to TI’s terms and conditions of sale supplied at the time of order acknowledgment.TI warrants performance of its hardware products to the specifications applicable at the time of sale in accordance with TI’s standard warranty.Testing and other quality control techniques are used to the extent TI deems necessary to support this warranty.Except where mandated by government requirements,testing of all parameters of each product is not necessarily performed.TI assumes no liability for applications assistance or customer product design.Customers are responsible for their products and applications using TI components.To minimize the risks associated with customer products and applications,customers should provide adequate design and operating safeguards.TI does not warrant or represent that any license,either express or implied,is granted under any TI patent right,copyright,mask work right,or other TI intellectual property right relating to any combination,machine,or process in which TI products or services are rmation published by TI regarding third-party products or services does not constitute a license from TI to use such products or services or a warranty or endorsement e of such information may require a license from a third party under the patents or other intellectual property of the third party,or a license from TI under the patents or other intellectual property of TI. Reproduction of information in TI data books or data sheets is permissible only if reproduction is without alteration and is accompanied by all associated warranties,conditions,limitations,and notices.Reproduction of this information with alteration is an unfair and deceptive business practice.TI is not responsible or liable for such altered documentation.Resale of TI products or services with statements different from or beyond the parameters stated by TI for that product or service voids all express and any implied warranties for the associated TI product or service and is an unfair and deceptive business practice.TI is not responsible or liable for any such statements.TI products are not authorized for use in safety-critical applications(such as life support)where a failure of the TI product would reasonably be expected to cause severe personal injury or death,unless officers of the parties have executed an agreement specifically governing such use.Buyers represent that they have all necessary expertise in the safety and regulatory ramifications of their applications,and acknowledge and agree that they are solely responsible for all legal,regulatory and safety-related requirements concerning their products and any use of TI products in such safety-critical applications,notwithstanding any applications-related information or support that may be provided by TI.Further,Buyers must fully indemnify TI and its representatives against any damages arising out of the use of TI products in such safety-critical applications.TI products are neither designed nor intended for use in military/aerospace applications or environments unless the TI products are specifically designated by TI as military-grade or"enhanced plastic."Only products designated by TI as military-grade meet military specifications.Buyers acknowledge and agree that any such use of TI products which TI has not designated as military-grade is solely at the Buyer's risk,and that they are solely responsible for compliance with all legal and regulatory requirements in connection with such use.TI products are neither designed nor intended for use in automotive applications or environments unless the specific TI products are designated by TI as compliant with ISO/TS16949requirements.Buyers acknowledge and agree that,if they use anynon-designated products in automotive applications,TI will not be responsible for any failure to meet such requirements. Following are URLs where you can obtain information on other Texas Instruments products and application solutions:Products ApplicationsAmplifiers Audio /audioData Converters Automotive /automotiveDSP Broadband /broadbandInterface Digital Control /digitalcontrolLogic Military /militaryPower Mgmt Optical Networking /opticalnetworkMicrocontrollers Security /securityLow Power /lpw Telephony /telephonyWirelessVideo&Imaging /videoWireless /wirelessMailing Address:Texas Instruments,Post Office Box655303,Dallas,Texas75265Copyright©2007,Texas Instruments Incorporated。
IXFJ40N30资料
Symbol Test Conditions Maximum RatingsV DSS T J = 25°C to 150°C300V VDGR T J = 25°C to 150°C; R GS = 1 M W 300V V GS Continuous ±20V V GSM Transient ±30V I D25T C = 25°C40A I DM T C = 25°C, pulse width limited by T JM 160A I AR T C = 25°C 40A E AR T C = 25°C30mJ dv/dt I S £ I DM , di/dt £ 100 A/m s, V DD £ V DSS ,5V/ns T J £ 150°C, R G = 2 W P D T C = 25°C300W T J -55 ... +150°C T JM 150°C T stg -55 ... +150°C T L1.6 mm (0.062 in.) from case for 10 s 300°C Weight5gSymbol Test ConditionsCharacteristic Values(T J = 25°C, unless otherwise specified)min.typ.max.V DSS V GS = 0 V, I D = 250 m A 300V V GS(th)V DS = V GS , I D = 4 mA 24V I GSS V GS = ±20 V DC , V DS = 0±100nA I DSS V DS = 0.8 • V DSS T J = 25°C 200m A V GS = 0 VT J = 125°C1mAR DS(on)V GS = 10 V, I D = 0.5 I D2580m WPulse test, t £ 300 m s, duty cycle d £ 2 %HiPerFET TMPower MOSFETsN-Channel Enhancement ModeHigh dv/dt, Low t rr , HDMOS TM FamilyPreliminary data sheetFeatures•Low profile, high power package •Long creep and strike distances •Easy up-grade path for TO-220designs•Low R DS (on) HDMOS TM process•Rugged polysilicon gate cell structure •Unclamped Inductive Switching (UIS)rated•Low package inductance -easy to drive and to protect •Fast intrinsic Rectifier Applications •DC-DC converters•Synchronous rectification •Battery chargers•Switched-mode and resonant-mode power supplies •DC choppers •AC motor control•Temperature and lighting controls •Low voltage relaysAdvantages•High power, low profile package •Space savings •High power density98536 1/99)G = Gate, D = Drain,S = Source,TAB = Drain(TAB)G D SéSymbolTest ConditionsCharacteristic Values(T= 25°C, unless otherwise specified)characteristic curves are located in the IXFH 40N30 data sheet.。
1N914中文资料
VF, INSTANTANEOUS FORWARD VOLTAGE (V) Fig. 1 Forward Characteristics 1N914, 1N914A
10,000
IR, LEAKAGE CURRENT (nA)
1000
100
10
VR = 20V
1 0 100 200
Tj, JUNCTION TEMPERATURE (°C) Fig. 3 Leakage Current vs Junction Temperature
DO-35 Min 25.40 ¾ ¾ ¾ Max ¾ 4.00 0.60 2.00
All Dimensions in mm
Maximum Ratings @ TA = 25°C unless otherwise specified
Characteristic Non-Repetitive Peak Reverse Voltage Peak Repetitive Reverse Voltage Working Peak Reverse Voltage DC Blocking Voltage RMS Reverse Voltage Forward Continuous Current (Note 1) Average Rectified Output Current (Note 1) 1N914 1N914A/B 1N914 1N914A/B Symbol VRM VRRM VRWM VR VR(RMS) IFM IO IFSM Pd RqJA Tj , TSTG Value 100 75 53 150 300 75 200 1.0 1.0 4.0 500 1.68 300 -65 to +175 Unit V V V mA mA A mW mW/°C K/W °C
MAX4472中文资料
Features
o Ultra-Low 750nA Supply Current Per Amplifier o Ultra-Low +1.8V Supply Voltage Operatommon-Mode Range o Outputs Swing Rail-to-Rail o Outputs Source and Sink 11mA of Load Current o No Phase Reversal for Overdriven Inputs o High 120dB Open-Loop Voltage Gain o Low 500µV Input Offset Voltage o 9kHz Gain-Bandwidth Product
1n4471二极管参数
1n4471二极管参数1.引言1.1 概述在现代电子技术中，二极管是一种基本的电子元件，也是电子电路中最常用、最重要的一种器件之一。
它由一个P型半导体和一个N型半导体组成，具有单向导电性，即只允许电流在一个方向上流动。
由于其简单且可靠的特性，二极管被广泛应用于各种电子设备和电路中。
本文将重点探讨1N4471二极管的参数。
1N4471是一种高速二极管，具有较高的反向电压和较快的开关速度，适用于高频率和高速应用。
了解1N4471二极管的参数对于正确选择和使用该器件至关重要。
在接下来的内容中，我们将首先介绍1N4471二极管的基本结构和工作原理。
然后，我们将详细讨论其主要参数，包括最大反向电压、平均整流电流、最大正向电流和最大反向恢复时间等。
此外，还将介绍一些与1N4471相关的应用注意事项和常见问题。
通过深入了解1N4471二极管的参数，读者将能够更好地理解和应用该器件。
在实际电路设计和电子设备维护中，正确选择和使用二极管是确保系统性能和可靠性的关键因素之一。
因此，本文将为读者提供一些有关1N4471二极管参数的重要信息和实用建议，以帮助他们更好地应对复杂的电子系统设计和故障排除任务。
接下来的章节将详细介绍本文的结构和目的，以及每个章节的要点和总结。
读者可以根据自己的需求选择阅读相关章节，从而更好地理解1N4471二极管参数的重要性和应用价值。
本文的目标是提供一份全面而有用的参考资料，以促进读者在电子技术领域的学习和实践中取得更好的成果。
1.2文章结构在文章结构部分，我们将对整篇文章的组织和内容进行概述和说明。
本文旨在讨论1n4471二极管的参数，以帮助读者更好地理解和应用该器件。
首先，我们将提供一个引言部分，介绍本文的目的和背景。
在这一部分中，我们将简要概述1n4471二极管的基本特点和应用领域，以便读者对该主题有一个初步的认识。
接着是正文部分，其中包括两个要点。
在第一个要点中，我们将详细介绍1n4471二极管的主要参数，如最大反向电压、最大工作电流、导通压降等。
常用稳压二极管技术参数及老型号代换
常用稳压二极管技术参数及老型号代换型号最大功耗 (mW) 稳定电压(V) 电流(mA) 代换型号国产稳压管日立稳压管HZ4B2 500 3.8 4.0 5 2CW102 2CW21 4B2HZ4C1 500 4.0 4.2 5 2CW102 2CW21 4C1HZ6 500 5.5 5.8 5 2CW103 2CW21A 6B1HZ6A 500 5.2 5.7 5 2CW103 2CW21AHZ6C3 500 6 6.4 5 2CW104 2CW21B 6C3HZ7 500 6.9 7.2 5 2CW105 2CW21CHZ7A 500 6.3 6.9 5 2CW105 2CW21CHZ7B 500 6.7 7.3 5 2CW105 2CW21CHZ9A 500 7.7 8.5 5 2CW106 2CW21DHZ9CTA 500 8.9 9.7 5 2CW107 2CW21EHZ11 500 9.5 11.9 5 2CW109 2CW21GHZ12 500 11.6 14.3 5 2CW111 2CW21HHZ12B 500 12.4 13.4 5 2CW111 2CW21HHZ12B2 500 12.6 13.1 5 2CW111 2CW21H 12B2HZ18Y 500 16.5 18.5 5 2CW113 2CW21JHZ20-1 500 18.86 19.44 2 2CW114 2CW21KHZ27 500 27.2 28.6 2 2CW117 2CW21L 27-3HZT33-02 400 31 33.5 5 2CW119 2CW21MRD2.0E(B) 500 1.88 2.12 20 2CW100 2CW21P 2B1RD2.7E 400 2.5 2.93 20 2CW101 2CW21SRD3.9EL1 500 3.7 4 20 2CW102 2CW21 4B2RD5.6EN1 500 5.2 5.5 20 2CW103 2CW21A 6A1RD5.6EN3 500 5.6 5.9 20 2CW104 2CW21B 6B2RD5.6EL2 500 5.5 5.7 20 2CW103 2CW21A 6B1RD6.2E(B) 500 5.88 6.6 20 2CW104 2CW21BRD7.5E(B) 500 7.0 7.9 20 2CW105 2CW21CRD10EN3 500 9.7 10.0 20 2CW108 2CW21F 11A2RD11E(B) 500 10.1 11.8 15 2CW109 2CW21GRD12E 500 11.74 12.35 10 2CW110 2CW21H 12A1RD12F 1000 11.19 11.77 20 2CW109 2CW21GRD13EN1 500 12 12.7 10 2CW110 2CW21H 12A3RD15EL2 500 13.8 14.6 15 2CW112 2CW21J 12C3RD24E 400 22 25 10 2CW116 2CW21H 24-1RD24F 400 24 28 10 2CW117 2CW21LRD36EL1 500 32 34 15 2CW119 2CW21M 33-2RD57E 500 48 54 10 1DS55-1805Z5.1Y 500 4.94 5.20 2CW103 2CW21A 5C205Z5.6Z 500 5.61 5.91 2CW104 2CW21B 6B205Z6.2Y 500 5.96 6.27 41 2CW104 2CW21B 6C205Z7.5Y 500 7.07 7.45 34 2CW105 2CW21C05Z7.5Z 500 7.3 7.7 34 2CW105 2CW21C 7C205Z9.1Y 500 8.9 9.3 30 2CW107 2CW21E 9C105Z12 500 11.13 12.35 21 2CW110 2CW21H05Z12Z 500 12.0 12.6 20 2CW110 2CW21H 12A305Z13X 500 12.11 12.75 19 2CW110 2CW21H 12A305Z13Z 500 13.5 14.1 18 2CW111 2CW21H 12C205Z13Y 500 12.55 13.21 19 2CW111 2CW21H 12B205Z15 500 14.4 15.0 17 2CW112 2CW21J 15-205Z15Y 500 13.89 14.62 17 2CW111 2CW21H 12C305Z18 500 16.5 18.5 14 2CW113 2CW21J05Z18Y 500 16.82 17.70 14 2CW113 2CW21J 18-1EQA01-11B 500 10.1 11.8 15 2CW109 2CW21GEQA01-12Z 500 11.2 13.1 15 2CW110 2CW21HEQA02-07B 400 6.66 7.01 20 2CW105 2CW21C 7A3EQA02-25A 500 24 25.5 2CW116 2CW21L 24-3TVSQA106SB 500 5.88 6.6 20 2CW104 2CW21BTVSQA111SB 500 10.4 11.6 10 2CW109 2CW21GTVSQA111SE 500 11 11.5 10 2CW109 2CW21G 11C2MA1130 1000 12.4 14.1 5 2CW111 2CW21HMA1330 500 31 35 25 2CW120 2CW21NM4030 500 2.9 3 5 2CW101 2CW21SuPC574JAG 200 31 35 25 2CW120 2CW21NRIMV 135 160 ZDW591N708 0.25 5.6 40 BWA54、2CW28-5.6V1N709 0.25 6.2 40 2CW55/B、BWA55/E1N710 0.25 6.8 36 2CW55A、2CW105-6.8V1N711 0.25 7.5 30 2CW56A、2CW28-7.5V、2CW106-7.5V 1N712 0.25 8.2 30 2CW57/B、2CW106-8.2V1N713 0.25 9.1 27 2CW58A/B、2CW741N714 0.25 10 25 2CW18、2CW59/A/B1N715 0.25 11 20 2CW76、2DW12F.BS31-121N716 0.25 12 20 2CW61/A、2CW77/A1N717 0.25 13 18 2CW62/A、2DW12G1N718 0.25 15 16 2CW112-15V、2CW78/A1N719 0.25 16 15 2CW63/A/B、2DW12H1N720 0.25 18 13 2CW20B、2CW64/B、2CW64-18 1N721 0.25 20 12 2CW65-20、2DW12I、BWA651N722 0.25 22 11 2CW20C、2DW12J1N723 0.25 24 10 WCW116、2DW13A1N724 0.25 27 9 2CW20D、2CW68、BWA68/D1N725 0.40 30 13 2CW119-30V1N726 0.40 33 12 2CW120-33V1N727 0.40 36 11 2CW120-36V1N728 0.40 39 10 2CW121-39V1N748 0.50 3.8～4.0 125 HZ4B21N752 0.50 5.2～5.7 80 HZ6A1N753 0.50 5.8～6.1 80 2CW1321N754 0.5 6.3～6.8 70 H27A1N755 0.50 7.1～7.3 65 HZ7.5EB1N757 0.50 8.9～9.3 52 HZ9C1N962 0.50 9.5～11 45 2CW1371N963 0.50 11～11.5 40 2CW138、HZ12A-21N964 0.50 12～12.5 40 HZ12C-2、MA1130TA1N969 0.50 21～22.5 20 RD245B1N4240A 1 10 100 2CW108-10V、2CW109、2DW5 1N4724A 1 12 76 2DW6A、2CW110-12V1N4728 1 3.3 270 2CW101-3V31N4729 1 3.6 252 2CW101-3V61N4729A 1 3.6 252 2CW101-3V61N4730A 1 3.9 234 2CW102-3V91N4731 1 4.3 217 2CW102-4V31N4731A 1 4.3 217 2CW102-4V31N4732/A 1 4.7 193 2CW102-4V71N4733/A 1 5.1 179 2CW103-5V11N4734/A 1 5.6 162 2CW103-5V61N4735/A 1 6.2 146 1W6V2、2CW104-6V21N4736/A 1 6.8 138 1W6V8、2CW104-6V81N4737/A 1 7.5 121 1W7V5、2CW105-7V51N4738/A 1 8.2 110 1W8V2、2CW106-8V21N4739/A 1 9.1 100 1W9V1、2CW107-9V11N4740/A 1 10 91 2CW286-10V、B563-101N4741/A 1 11 83 2CW109-11V、2DW61N4742/A 1 12 76 2CW110-12V、2DW6A1N4743/A 1 13 69 2CW111-13V、2DW6B、BWC114D 1N4744/A 1 15 57 2CW112-15V、2DW6D1N4745/A 1 16 51 2CW112-16V、2DW6E1N4746/A 1 18 50 2CW113-18V、1W18V1N4747/A 1 20 45 2CW114-20V、BWC115E1N4748/A 1 22 41 2CW115-22V、1W22V1N4749/A 1 24 38 2CW116-24V、1W24V1N4750/A 1 27 34 2CW117-27V、1W27V1N4751/A 1 30 30 2CW118-30V、1W30V、2DW19F 1N4752/A 1 33 27 2CW119-33V、1W33V1N4753 0.5 36 13 2CW120-36V、1/2W36V1N4754 0.5 39 12 2CW121-39V、1/2W39V1N4755 0.5 43 12 2CW122-43V、1/2W43V1N4756 0.5 47 10 2CW122-47V、1/2W47V1N4757 0.5 51 9 2CW123-51V、1/2W51V1N4758 0.5 56 8 2CW124-56V、1/2W56V1N4759 0.5 62 8 2CW124-62V、1/2W62V1N4760 0.5 68 7 2CW125-68V、1/2W68V1N4761 0.5 75 6.7 2CW126-75V、1/2W75V1N4762 0.5 82 6 2CW126-82V、1/2W82V1N4763 0.5 91 5.6 2CW127-91V、1/2W91V1N4764 0.5 100 5 2CW128-100V、1/2W100V1N5226/A 0.5 3.3 138 2CW51-3V3、2CW52261N5227/A/B 0.5 3.6 126 2CW51-3V6、2CW52271N5228/A/B 0.5 3.9 115 2CW52-3V9、2CW52281N5229/A/B 0.5 4.3 106 2CW52-4V3、2CW52291N5230/A/B 0.5 4.7 97 2CW53-4V7、2CW52301N5231/A/B 0.5 5.1 89 2CW53-5V1、2CW52311N5232/A/B 0.5 5.6 81 2CW103-5.6、2CW52321N5233/A/B 0.5 6 76 2CW104-6V、2CW52331N5234/A/B 0.5 6.2 73 2CW104-6.2V、2CW52341N5235/A/B 0.5 6.8 67 2CW105-6.8V、2CW5235型号稳压值(V) 稳定电流 (MA) 功率(mW) 型号稳压值(V) 稳定电流 (MA) 功率(mW) MA1030 3 5 400 MA2180 18 20 1000MA1033 3.3 5 400 MA2200 20 20 1000MA1036 3.6 5 400 MA2220 22 10 1000MA1039 3.9 5 400 MA2240 24 10 1000MA1043 4.3 5 400 MA2270 27 5 1000MA1047 4.7 5 400 MA2300 30 5 1000MA1051 5.1 5 400 MA2330 33 5 1000MA1056 5.6 5 400 MA2360 36 5 1000MA1062 6.2 5 400 MA3047 4.7 5 150MA1068 6.8 5 400 MA3051 5.1 5 150MA1075 7.5 5 400 MA3056 5.6 5 150MA1082 8.2 5 400 MA3062 6.2 5 150MA1091 9.1 5 400 MA3082 8.2 5 150MA1100 10 5 400 MA3091 9.1 5 150MA1110 11 5 400 MA3100 10 5 150MA1114 11.4 10 400 MA3110 11 5 150MA1120 12 5 400 MA3120 12 5 150MA1130 13 5 400 MA3130 13 5 150MA1140 14 5 400 MA3150 15 5 150MA1150 15 5 400 MA3160 16 5 150MA1160 16 5 400 MA3180 18 5 150MA1180 18 5 400 MA3200 20 5 150MA1200 20 5 400 MA3220 22 5 150MA1220 22 5 400 MA3240 24 5 150MA1240 24 5 400 MA3270 27 2 150MA1270 27 2 400 MA3300 30 2 150MA1300 30 2 400 MA3330 33 2 150MA1330 33 2 400 MA3360 36 2 150MA1360 36 2 400 MA4030 3 5 370MA2051 5.1 40 1000 MA4033 3.3 5 370MA2056 5.6 40 1000 MA4036 3.6 5 370MA2062 6.2 40 1000 MA4039 3.9 5 370 MA2068 6.8 40 1000 MA4043 4.3 5 370 MA2075 7.5 40 1000 MA4047 4.7 5 370 MA2082 8.2 40 1000 MA4051 5.1 5 370 MA2091 9.1 40 1000 MA4056 5.6 5 370 MA2100 10 40 1000 MA4062 6.2 5 370 MA2110 11 5 1000 MA4068 6.8 5 370MA2120 12 5 1000 MA4075 7.5 5 370MA2130 13 5 1000 MA4082 8.2 5 370MA2150 15 5 1000 MA4091 9.1 5 370MA2160 16 5 1000 MA4100 10 5 370MA4110 11 5 370 BZX55C6V8 6.8 5 500 MA4120 12 5 370 BZX55C7V5 7.5 5 500 MA4130 13 5 370 BZX55C8V2 8.2 5 500 MA4140 14 5 370 BZX55C9V1 9.1 5 500 MA4150 15 5 370 BZX55C10 10 5 500MA4160 16 5 370 BZX55C11 11 5 500MA4180 18 5 370 BZX55C12 12 5 500MA4200 20 5 370 BZX55C13 13 5 500MA4220 22 5 370 BZX55C15 15 5 500MA4240 24 5 370 BZX55C16 16 5 500MA4270 27 2 370 BZX55C18 18 5 500MA4300 30 2 370 BZX55C20 20 5 500MA4330 33 2 370 BZX55C22 22 5 500MA4360 36 2 370 BZX55C24 24 5 500MA5047 4.7 5 500 BZX55C27 27 5 500 MA5051 5.1 5 500 BZX55C30 30 5 500 MA5056 5.6 5 500 BZX55C33 33 5 500 MA5062 6.2 5 500 BZX55C36 36 5 500 MA5068 6.8 5 500 BZX55C39 39 5 500 MA5075 7.5 5 500 BZX55C43 43 2.5 500 MA5082 8.2 5 500 BZX55C47 47 2.5 500 MA5091 9.1 5 500 BZX55C51 51 2.5 500 MA5100 10 5 500 BZX55C56 56 2.5 500 MA5110 11 5 500 BZX55C62 62 2.5 500 MA5120 12 5 500 BZX85C2V7 2.7 80 1300 MA5130 13 5 500 BZX85C3V0 3.0 80 1300MA5160 16 5 500 BZX85C3V6 3.6 70 1300MA5180 18 5 500 BZX85C3V9 3.9 60 1300MA5200 20 5 500 BZX85C4V3 4.3 50 1300MA5240 24 5 500 BZX85C4V7 4.7 45 1300 BZX55C2V4 2.4 5 500 BZX85C5V1 5.1 45 1300 BZX55C2V7 2.7 5 500 BZX85C5V6 5.6 45 1300 BZX55C3V0 3.0 5 500 BZX85C6V2 6.2 35 1300 BZX55C3V3 3.3 5 500 BZX85C6V8 6.8 35 1300 BZX55C3V6 3.6 5 500 BZX85C7V5 7.5 35 1300 BZX55C3V9 3.9 5 500 BZX85C8V2 8.2 25 1300BZX55C4V3 4.3 5 500 BZX85C9V1 9.1 25 1300 BZX55C4V7 4.7 5 500 BZX85C10 10 25 1300 BZX55C5V1 5.1 5 500 BZX85C11 11 20 1300 BZX55C5V6 5.6 5 500 BZX85C12 12 20 1300 BZX55C6V2 6.2 5 500 BZX85C13 13 20 1300 BZX85C15 15 15 1300 BZX79A9V1 9.1 5 400 BZX85C16 16 15 1300 BZX79A10 10 5 400 BZX85C18 18 15 1300 BZX79A11 11 5 400 BZX85C20 20 10 1300 BZX79A12 12 5 400 BZX85C22 22 10 1300 BZX79A13 13 5 400 BZX85C24 24 10 1300 BZX79A15 15 5 400 BZX85C27 27 8 1300 BZX79A16 16 5 400BZX85C30 30 8 1300 BZX79A18 18 5 400BZX85C33 33 8 1300 BZX79A20 20 5 400BZX85C36 36 8 1300 BZX79A22 22 5 400BZX85C39 39 6 1300 BZX79A24 24 5 400BZX85C43 43 6 1300 BZX79A27 27 2 400BZX85C47 47 4 1300 BZX79A30 30 2 400BZX85C51 51 4 1300 BZX79A33 33 2 400BZX85C56 56 4 1300 BZX79A36 36 2 400BZX85C62 62 4 1300 BZX79A39 39 2 400BZX55C68 68 2.5 500 BZX79A43 43 2 400 BZX55C75 75 2.5 500 BZX79A47 47 2 400 BZX55C82 82 2.5 500 BZX79A51 51 2 400 BZX55C91 91 1 500 BZX79A56 56 2 400BZX55C110 110 1 500 BZX79A68 68 2 400BZX55C120 120 1 500 BZX79A75 75 2 400BZX55C130 130 1 500 BZX79C2V4 2.4 5 500BZX55C150 150 1 500 BZX79C2V7 2.7 5 500BZX55C160 160 1 500 BZX79C3V0 3.0 5 500BZX55C180 180 1 500 BZX79C3V3 3.3 5 500BZX55C200 200 1 500 BZX79C3V6 3.6 5 500BZX79A2V4 2.4 5 400 BZX79C3V9 3.9 5 500BZX79A2V7 2.7 5 400 BZX79C4V3 4.3 5 500BZX79A3V0 3.0 5 400 BZX79C4V7 4.7 5 500BZX79A3V3 3.3 5 400 BZX79C5V1 5.1 5 500BZX79A3V6 3.6 5 400 BZX79C5V6 5.6 5 500BZX79A3V9 3.9 5 400 BZX79C6V2 6.2 5 500BZX79A4V3 4.3 5 400 BZX79C6V8 6.8 5 500BZX79A4V7 4.7 5 400 BZX79C7V5 7.5 5 500BZX79A5V1 5.1 5 400 BZX79C8V2 8.2 5 500BZX79A5V6 5.6 5 400 BZX79C9V1 9.1 5 500BZX79A6V2 6.2 5 400 BZX79C10 10 5 500BZX79A6V8 6.8 5 400 BZX79C11 11 5 500BZX79A7V5 7.5 5 400 BZX79C12 12 5 500BZX79A8V2 8.2 5 400 BZX79C13 13 5 500整流二极管：整流二极管是面接触型的，多采用硅材料构成。