阿尔西空调样本-DATACOOL-C1301V01.3
阿尔西空调样本-DATACOOL-C1301V01.3
电加热/电加湿配置表
机组型号
项目
6
电加热量
9
(kW)
12
13.5
5
加湿量
8
10
(kg/h)
13
15
15E1C2
● ○ — — ● ○ — — —
18E1C2
● ○ — — ● ○ — — —
注：“●”表示标准配置，“○”表示可选项，“—”表示无。
22E1C3
— ● ○ ○ ● ○ ○ ○ ○
25E1C3
N2 N16
06
技术参数表
室内机组
机组型号 送风方式(1) 制冷量
全冷⑵ 显冷⑵ 全冷⑶ 显冷⑶ 压缩机 形式 输入功率⑵ 输入电流⑵ 输入功率⑶ 输入电流⑶ 送风机 形式 风机数量 风量 机外余压 输入功率 输入电流 电加热器⑷ 形式 供热量 工作级 加湿器⑷ 形式 加湿量 输入功率 室外机组⑸ 型号×数量 机组供电 电源 机组最大运行功率⑹ 机组最大运行电流⑹ 管路连接 冷凝水排水Φ 加湿器进水Φ 制冷剂管路连接形式 气管Φ 液管Φ 外形尺寸及重量 宽 深 高 重量
上送风（下回风）方式不需要高架地板，对机房的安装条 件要求少，容易安装，因此在小型机房被广泛使用。
不过，由于这种送风方式的气流方向与空气的自然流动方 向（热空气向上走，冷空气往下沉）相反，从能量效率方 面来讲，这种方式要差一些，与另外两种方式相比，大约 有2-5%的差异。参见下图。
下送风系统应用于铺设有高架地板的机房。与上送风系统 相比，下送风系统的送风方式使机房内容易布局成冷热通 道隔离的气流组织方式，制冷效率明显高于上送风系统, 见下图。但机房造价也相对较高。
控制精度 温度控制范围：15~35℃，控制精度：±1℃ 湿度控制范围：35~80%，控制精度：±5%
阿尔西
air-sys阿尔西机房专用恒温恒湿精密空调故障报警维护维修说明当air-sys阿尔西机房专用恒温恒湿精密空调机组发生故障时，报警信号将通过声光报警由电脑显示板显示出来。
下面将对各项报警作出详细说明，可帮助用户分析查找故障原因。
以指导维修。
1 EXT. ENABLE OFF：外部有效关（空调机组禁止启动），阿尔西300x卡，A1输入口，CnB接头，该故障出现时，除冷凝风扇可继续工作外，禁止所有控制和比例信号输出。
此报警不启动音响报警、报警继电器和红色LED灯指示。
此报警不存储在最后10个报警内。
当air-sys阿尔西机房精密空调机组处于该报警情况下时，除HI/LO TEMP 和HI/LO HUMID之外的任何其他报警将被记录及显示。
空调维护报警维修后自动复位。
2 SUPPLY FAN FAIL (主风机热保护)：阿尔西300x卡，A2输入口，CnB接头此报警停止air-sys阿尔西空调机组，直到热保护复位，如果在30分钟内，此报警重新发生，除冷凝风扇外，air-sys阿尔西机房恒温恒湿精密空调整机被子锁住，即使在备用状态下，此报警也可能发生，维护维修后键盘手动复位。
3 AIR FLOW LOSS（风量损失）：阿尔西3100-A卡，A8输入口，CnR接头，此报警停止机组的其它功能，除送风机与冷凝风机继电器之外，此报警有10秒的延时，维护维修后自动复位。
4 CLOGGED FILTER（过滤器堵塞）：阿尔西3100-A卡，A9输入口，CnR接头。
此报警不停止air-sys阿尔西机房专用恒温恒湿精密空调机组并有此报警有5秒的延时。
维护维修后自动复位。
5 COND. FAN 1 FAIL冷凝风机1故障-仅用于DXA机组：5 LIMIT THERM 1 极限温度控制1-DXW机组：阿尔西300x卡，A3输入口，CnB接头。
此报警停止压缩机2的工作及冷凝风机1（DXA机组）工作，停止向P5输出口输出信号，直到热保护复位。
水冷冷水机组样本
FHR系列热回收式水冷冷水机组，采用特殊的双水路冷凝 器可回收全部冷凝热量。为用户提供部分生活用水。 PHR部分热回收型(PHR系列，选用功能） PHR系列热回收式水冷冷水机组，可回收部分冷凝热量并 提高机组运行性能，为用户提供部分生活热水，取得非常 可观的节能效果。 低噪音型 所有机型均可选择低噪音型，其噪音比标准型降低10 ～15分贝。 蓄冰功能（选用功能） 机组标准配置双水温设置点，在用户要求的情况下，可 以将出水温度调整至-4℃/-8℃(蓄冰工况)。
出水温度极限报警 当出水温度降低至3℃时，电脑立即停止压缩机工作并启动 蒸发器防冻电加热器。
传感器故障报警 电脑对机组使用的压力及温度传感器进行监测，一旦失效立 即终止其工作并发出报警。
供电电压过高/ 低报警 对供电电压连续进行监测，一旦超出设定范围，立即终止机 组工作并发出相应报警。
特殊功能 短信遥控
远程联网监控
独立集中监控系统（IntelliVision2000系统） 由阿尔西公司独立开发的全中文监控系统IntelliVision2000具备 强大的联网监控功能，具备灵活多样的连接形式，并可同时监控 阿尔西公司的全部智能控制空调产品。 IntelliVision2000运行在一台普通个人电脑中，可以通过直联或 借助调制解调器对远端设备进行监控与管理，机组的所有运行参 数、运行状态以及发生的报警可及时而迅速的反映在监控画面 上，通过授权甚至可以远端开停机组、修改运行参数以及复位机 组报警。 Intellivision2000 可连接至阿尔西公司维修中心，或将相关数据 传送至维修中心，由有经验的工程师协助解决出现的问题，达到 缩短维修时间，降低维修费用之目的。
机组型号说明
Atlas Copco Z压缩机系列产品说明书
Oil-free rotary screw compressorsZR/ZT 110-275 (FF) & ZR/ZT 132-315 VSD (FF)Setting the standard in energy efficiency, safety and reliability The shortest route to superior productivity is to minimize operational cost while maintaining an uninterrupted supply of the right quality of air. The Atlas Copco Z compressor series is focused on effectively saving energy, ensuring product safety –only oil-free machines exclude contamination risks for 100% – and guaranteeing the utmost reliability around the clock. And not just today, but day after day, year after year,with minimal maintenance cost, few service interventions and long overhaul intervals.Highest reliabilityFor 60 years, Atlas Copco Z compressors have set the benchmark for durability. T hey are built using long-standing internal engineering practices, and are designed and manufactured according to ISO 9001, ISO 14001, ISO 22000& OHSAS 18001. T he high-end ZR/ZT uses time-provenstate-of-the-art screw technology, cooling and pulsation dampers and provides you with the highest reliability. 100% oil-free compressed airThe ZR/ZT offers you 100% pure, clean air that complies with ISO 8573-1 CLASS 0 (2010) certification. T his means zero riskof contamination; zero risk of damaged products; zero risk of losses from operational downtime; and zero risk of damaging your company’s hard-won professional reputation. Maximum energy efficiencyThe ZR/ZT’s superior oil-free screw elements provide the optimum combination of high Free Air Delivery (FAD) with the lowest energy consumption. Ample sized cooling, low pressure drops and an extremely efficient drive train result in the highest compressor package efficiency.The most complete packageWith the ZR/ZT compressor, Atlas Copco provides a superior solution without hidden costs. T he totally integrated,ready-to-use package includes internal piping, coolers, motor, lubrication and control system. T he Full Feature version even integrates an IMD adsorption dryer for an impeccable end product. Installation is fault-free, commissioning time is low and no external instrument air is required. Y ou simply plug and run. Global presence - local serviceOur aftermarket product portfolio is designed to add maximum value for our customers by ensuring the optimum availability and reliability of their compressed air equipment with the lowest possible operating costs. We deliver this complete service guarantee through our extensive service organization,maintaining our position as leader in compressed air.100% certified oil-free airAtlas Copco is renowned for designing and manufacturing some of the most durable oil-free screw compressors. T he ZR/ZT high-end rotary screw compressor comes out of this strong tradition.Ideal for industries where high-quality oil-free air is key, the ZR/ZT offers the highest reliability and safety in combination with low energy costs.Food & beverage• 100% pure, clean, oil-free air for all kinds of applications(e.g. fermentation, packaging, aeration, transportation,filling & capping, cleaning, instrument air).• ISO 8573-1 CLASS 0 (2010) certification to avoidcompromising the purity of your end productand ensure zero risk of contamination.T extiles• Easy and quick installation.• A completely, fully integrated, ready-to-use solution.Oil & gas• Years of experience in providing compressed airfor the oil & gas industry.• 100% oil-free compressed air for control/instrumentair or buffer air.• Strong global support network to provide 24/7 assistance.Power plants• Ideal for applications such as flue gas desulphurization,oxidation air, and fluidized beds.• Continuous operation.Class 0:the industry standardOil-free air is used in all kinds of industries whereair quality is paramount for the end product and production process. T hese applications includefood and beverage, pharmaceutical, chemical and petrochemical, semiconductor and electronics,the medical sector, automotive paint spraying, textile and many more. In these critical environments, contamination by even the smallest quantities of oil can result in costly production downtime and product spoilage.First in oil-free air technologyOver the past sixty years Atlas Copco has pioneered the development of oil-free air technology, resulting in a rangeof air compressors and blowers that provide 100% pure, clean air. Through continuous research and development, Atlas Copco achieved a new milestone, setting the standard for air purityas the first manufacturer to be awarded CLASS 0 certification. Eliminating any riskAs the industry leader committed to meeting the needs of the most demanding customers, Atlas Copco requested the renownedTÜV institute to type-test its range of oil-free compressors and blowers. Using the most rigorous testing methodologies available, all possible oil forms were measured across a range of temperatures and pressures. T he TÜV found no traces of oil at all in the outputair stream.concentration in total oil content).321High efficiency coolers and water separator• Corrosion resistant stainless steel tubing*.• Highly reliable robot welding; no leakages*.• Aluminium star insert increases heat transfer*.• Water separator with labyrinth design to efficiently separate the condensate from the compressed air.• Low moisture carry-over protects downstream equipment.3World-class oil-free compression element• Unique Z seal design guarantees 100% certified oil-free air.• Atlas Copco superior rotor coating for high efficiency and durability.• Cooling jackets.2Throttle valve with load/unload regulation• No external air supply required.• Mechanical interlock of inlet and blow-off valve.• Low unload power.1* Only for ZR water-cooled versions.45AirWaterOilMotor• IP55 T EFC protection against dust and humidity.• High efficiency fixed speed IE3 motor (equal to NEMA Premium).4Advanced Elektronikon ®• Large 5.7” sized color display available in 31 languages for optimal ease of use.• Controls the main drive motor and regulates system pressure to maximize energy efficiency.5Water-cooled ZR Pack123Silenced canopy• Base frame with forklift slot.• Fully packaged, easy to install.• Easy ducting.1Efficient intake air filtration• 2-stage dust removal system (99.9% for 3 micron).• Low pressure drop.• Efficient protection of the compressor.• Minimum intake losses.2High-efficiency motor + VSD• TEFC IP55 motor protects against dust and chemicals.• Continuous operation under severe ambient temperature conditions.• Full regulation between 30 to 100% of the maximum capacity.34Full Feature: IMD adsorption dryer• Eliminates the moisture before it enters the air net.• Ensuring a reliable process and a top quality end product.• No external energy is needed to dry the air, resulting in high energy savings and no compressed air losses.• Minimal pressure drop.4Air outAir-cooled ZT Full FeatureAirWaterOilVSD: driving down energy costsOver 80% of a compressor’s lifecycle cost is taken up by the energy it consumes. Moreover, the generation of compressed air can account for more than 40% of a plant’s total electricity bill. T o cut your energy costs, Atlas Copco pioneered Variable Speed Drive (VSD) technology in the compressed air industry. VSD leads to major energy savings, while protecting the environment for future generations. T hanks to continual investments in this technology, Atlas Copco offers the widest range of integrated VSD compressorson the market.EnergyEnergy savings with VSD Investment MaintenanceEnergy savings of up to 35%Atlas Copco's VSD technology closely follows the air demand by automatically adjusting the motor speed. This results in large energy savings of up to 35%. The Life Cycle Cost of a compressor can be cut by an average of 22%. In addition, lowered system pressure with VSD minimizes energy use across your production dramatically.T otal compressor lifecycle costVSD?1The Elektronikon® controls both the compressor and the integrated converter, ensuring maximum machine safety within parameters.2Flexible pressure selection from 4 to 10.4 bar with VSD reduces electricity costs.3Specific converter and motor design (with protected bearings) for the highest efficiency acrossthe speed range.4Electric motor specifically designed for low operating speeds with clear attention to motor cooling andcompressor cooling requirements.5All Atlas Copco VSD compressors are EMC tested and certified. Compressor operation does notinfluence external sources and vice versa.6Mechanical enhancements ensure that all components operate below critical vibration levels throughout theentire compressor speed range.7 A highly efficient frequency converter in a cubicleensures stable operation in high ambient temperatures up to 50°C/122°F (standard up to 40°C/104°F).8No ‘speed windows’ that can jeopardize the energy savings and the stable net pressure. T urndown capability of the compressor is maximized to 70-75%.9Net pressure band is maintained within 0.10 bar, 1.5 psi.Monitoring and control:how to get the most from the leastThe Elektronikon ® unit controller is specially designed to maximize the performance of your compressors and air treatment equipment under a variety of conditions. Our solutions provide you with key benefits such as increased energy efficiency, lower energy consumption, reduced maintenance times and less stress… less stress for both you and your entire air system.Intelligence is part of the package• High resolution color display gives you an easy to understand readout of the equipment’s running conditions. • Clear icons and intuitive navigation provides you fast access to all of the important settings and data. • Monitoring of the equipment running conditions and maintenance status; bringing this information to your attention when needed.• Operation of the equipment to deliver specifically and reliably to your compressed air needs.• Built-in remote control and notifications functions provided as standard, including simple to use Ethernet based communication.• Support for 31 different languages, including character based languages.Online & mobile monitoringMonitor your compressors over the Ethernet with the new Elektronikon ® controller. Monitoring features include warning indications, compressor shut-down andmaintenance scheduling. An Atlas Copco App is available for iPhone/Android phones as well as iPad and Android tablets. It allows fingertip monitoring of your compressed air system through your own secured network.• A remote monitoring system that helps you optimize your compressed air system and save you energy and cost.• It offers you a complete insight in your compressed air network and anticipates on potential problems by warning you up-front.*Please contact your local sales representative for more information.SMART LINK *:Data monitoring programProtecting your productionUntreated compressed air contains moisture and possibly dirt particles that can damage your air system and contaminate your end product. T he resulting maintenance costs far exceed air treatment costs. Atlas Copco believes in effective prevention and provides a complete range of air treatment solutions to protect investments, equipment, production processes and end products.Increase production reliabilityLow quality air heightens the risk of corrosion, which can lower the life span of production equipment. T he air treatment solutions produce clean air that enhances your system’s reliability, avoiding costly downtime and production delays.Safeguard production qualityCompressed air coming into contact with your final products should not affect their quality. Atlas Copco provides clean,dry air to protect your production and reputation in the market.Supreme energy and cost savingsAtlas Copco’s quality air solutions stand for substantial energy savings all day, every day. T aking technology to a new level,these products achieve maximum cost savings.Proven peace of mindBuilding on know-how and years of experience, the entire Atlas Copco quality air range is produced in-house and tested using the most stringent methods in the industry.A dryer solution for every needUntreated compressed air contains moisture and possibly dirt particles that can damage your air system and contaminate your end product. T he resulting maintenance costs far exceed air treatment costs. Atlas Copco believes in effective prevention and provides a complete range of air treatment solutions to protect investments, equipment, production processes and end products.BD/BD +-70°C/-40°C/-20°C -94°F/-40°F/-4°FHeat reactivated adsorption dryer• Use of electrical heaters for regenerating the desiccant• Limited pressure drop• Variants without loss of compressed airFD/FD +(VSD)+3°C/+20°C +37°F/+68°FRefrigerant dryer• Use of cooling circuit for cooling down compressed air • Guaranteed pressure dew points• Lowest energy consumption in all operating conditions • Air and water cooled variantsMD-20°C/+3°C -4°F/+37°FMDG-40°C/-20°C -40°F/-4°FRotary drum heat of compression dryers• Use of freely available heat of compression • Negligible power consumption• Variants with extra heat augmentation for lower dew pointsND-40°C/-20°C -40°F/-4°FDryers overviewD e w p o i n t (°C )D e w p o i n t (°F )Flow (l/s)Flow (cfm)+3+37-20-4-40-40-70-94To further protect your investment, equipment and processes, Atlas Copco presents a full line-up of innovative quality air solutions to suit the high quality requirements of your specific application.45213A complete Full Feature packageAtlas Copco’s Full Feature concept stands for a compact, all-in-one quality air solution. Integrating the IMD dryer and its Variable Speed Drive on VSD models, this integrated package offers the highest quality air at the lowest possible cost.Protect your compressed air systemA dry compressed air system is essential to maintain the reliability of production processes and the quality of the end products. Untreated air can cause corrosion in the pipe work, premature failure of pneumatic equipment and product spoilage.IMD adsorption dryerThe IMD adsorption dryer eliminates the moisture before it enters the air net,ensuring a reliable process and an impeccable end product. As no external energy is needed to dry the air, large savings are obtained. T he pressure drop through the dryer is minimal, which again cuts down the operating cost.The IMD drying principle1 Hot unsaturated air2 Hot saturated air3 Cold saturated air4 Dry air5 Drying sectionOptimize your systemWith the ZR/ZT , Atlas Copco provides an all-in-one standard package incorporating the latest technology in a built-to-last design. T o further optimize your ZR/ZT’s performance or to simply tailor it to your specific production environment, optional features are available.Engineered solutionsAtlas Copco recognizes the need to combine our serially produced compressors and dryers with thespecifications and standards applied by major companies for equipment purchases. Strategically located departments within the Atlas Copco Group take care of the design and manufacturing of customized equipment to operate at extreme temperatures, often in remote locations.Innovative technologyAll equipment is covered by our manufacturer warranty.The reliability, longevity and performance of our equipment will not be compromised. A global aftermarket operation employing 360 field service engineers in 160 countries ensures reliablemaintenance by Atlas Copco as part of a local service operation.Innovative engineeringEach project is unique and by entering into partnership with our customers, we can appreciate the challenge at hand, ask the relevant questions and design the best engineered solutionfor all your needs.Options• : Optional- : Not available(*) Maximum intake/cooling air temperature is 50°C/122 °F for HAT versions.Please note the availability of the option depends on the chosen configuration.ZR 110-275 (FF)(1) Unit performance measured according to ISO 1217, Annex C & E, Edition 4 (2009).Reference conditions:- Relative humidity 0%.- Absolute inlet pressure: 1 bar (14.5 psi).- Intake air temperature: 20°C/68°F.FAD is measured at the following working pressures: Fixed speed:- 7/7.5/8.6 bar versions at 7 bar.- 10/10.4 bar versions at 9 bar.- 13 bar version at 12 bar.For VSD: at their maximum working pressure.(2) A-weighted emission sound pressure level at the work station (LpWSAd).Measured according to ISO 2151: 2004 using ISO 9614/2 (sound intensity scanning method).The added correction factor (+/- 3 dB(A)) is the total uncertainty value (KpAd) conform with the test code.(3) Not available as FF variant.CABZT 110-275 (FF)(1) Unit performance measured according to ISO 1217, Annex C & E, Edition 4 (2009).Reference conditions: - Relative humidity 0%.- Absolute inlet pressure: 1 bar (14.5 psi). - Intake air temperature: 20°C/68°F .FAD is measured at the following working pressures:Fixed speed:- 7/7.5/8.6 bar versions at 7 bar. - 10/10.4 bar versions at 9 bar. - 13 bar version at 12 bar.For VSD: at their maximum working pressure.(2) A-weighted emission sound pressure level at the work station (LpWSAd).Measured according to ISO 2151: 2004 using ISO 9614/2 (sound intensity scanning method).The added correction factor (+/- 3 dB(A)) is the total uncertainty value (KpAd) conform with the test code.(1) For the working pressure of the FF variant, please consult Atlas Copco.(2) Unit performance measured according to ISO 1217, Annex C & E, Edition 4 (2009).Reference conditions:- Relative humidity 0%.- Absolute inlet pressure: 1 bar (14.5 psi).- Intake air temperature: 20°C/68°F.FAD is measured at the following working pressures: Fixed speed:- 7/7.5/8.6 bar versions at 7 bar.- 10/10.4 bar versions at 9 bar.- 13 bar version at 12 bar.For VSD: at their maximum working pressure.(3) A-weighted emission sound pressure level at the work station (LpWSAd).Measured according to ISO 2151: 2004 using ISO 9614/2 (sound intensity scanning method).The added correction factor (+/- 3 dB(A)) is the total uncertainty value (KpAd) conform with the test code.ZR 132-315 VSD (FF) (50/60 Hz)(1) For the working pressure of the FF variant, pleaseconsult Atlas Copco.(2) Unit performance measured according to ISO 1217, Annex C & E, Edition 4 (2009).Reference conditions: - Relative humidity 0%.- Absolute inlet pressure: 1 bar (14.5 psi). - Intake air temperature: 20°C/68°F .FAD is measured at the following working pressures:Fixed speed:- 7/7.5/8.6 bar versions at 7 bar. - 10/10.4 bar versions at 9 bar. - 13 bar version at 12 bar.For VSD: at their maximum working pressure.(3) A-weighted emission sound pressure level at the work station (LpWSAd).Measured according to ISO 2151: 2004 using ISO 9614/2 (sound intensity scanning method).The added correction factor (+/- 3 dB(A)) is the total uncertainty value (KpAd) conform with the test code.ZT 132-315 VSD (FF) (50/60 Hz)DimensionsCABCOMMITTED TO SUSTAINABLE PRODUCTIVITY2935 0538 14 © 2017, A t l a s C o p c o , B e l g i u m . A l l r i g h t s r e s e r v e d . D e s i g n s a n d s p e c i fi c a t i We stand by our responsibilities towards our customers, towards the environment and the people around us. We make performance stand the test of time. T his is what we call – Sustainable Productivity.。
阿尔西数据中心制冷解决方案
数据中心专用空调系统解决方案阿尔西集团2010年12月目 录一、前言 (2)二、数据中心空调制冷解决方案 (4)2.1、数据中心空调系统的重要性 (4)2.2、数据中心空调系统的关键环节 (4)2.3、数据中心空调系统全面解决方案 (4)2.4、中央冷源解决方案 (6)2.5、单元式空调系统解决方案 (12)2.6、高热流密度解决方案 (17)2.7、集装箱数据中心解决方案 (19)2.8、局部热点解决方案 (21)2.9、节能改造解决方案 (22)三、附录 (26)3.1、集团简介 (26)3.2、设备介绍 (26)3.3、成功案例 (27)一、前言随着新一代数据中心的建设，供电能耗问题，已经成为了所有的数据中心无法回避的问题。
通常，一个投资几百万元的数据中心，每年运营所产生的能耗成本就高达几十万元。
CIO把数据中心评价为“建得起而用不起”。
在能源日趋稀缺的状态下，利用各种新技术和管理手段，获得“增容不增耗”的绿色数据中心解决方案已成为行业发展的当务之急。
事实上，比起前几年来，企业在数据中心建设中已经更加注意能耗问题，但是，数据中心仍然和高额的电力和散热成本相伴随。
主要原因在于，随着新一代数据中心的建设，网络、服务器、存储等设备进一步集中，这就对数据中心的环境管理提出了新的要求。
就拿刀片服务器来说，它的设计特点是在狭小的空间内安装大量的服务器，每平米的功耗大量增加，企业对IT系统的要求愈加提高，电力供应系统密度加大，生产的热量更加集中和庞大，问题也就变得愈发严重。
据统计，维护一个数据中心的能耗中，真实用于IT设备的电力，大约30%~50%，剩余维护费用中冷却费用占到了40%~50%，甚至更高。
能耗的增加带来了热量，热量的增长也扩大了能耗。
而另外，更大的热量密度会增加这些影响。
作为如今业界的热点，建设新一代数据中心，除了资源整合等之外，实现绿色节能也是时代对企业提出的新的要求。
不仅是保护环境的需要，同时，高额的维护和能耗费用也让这成为企业不得不考虑的问题。
阿尔西空调
03
安静清洁
D A T A C O O L系列产品通过合理地配置选件，如：在机组 双层侧面板之间安装保温消声材料，内层加装多孔消声 板，为压缩机加装消音罩，以及安装带橡胶减振垫的高度 可调的地板支架等措施，降低噪音5～10dB（A）。
D A T A C O O L系列产品的空气过滤器采用可清洗式合成纤 维过滤器，过滤效率为G4，即粒径为5μ的灰尘的过滤效 果为80%，粒径为1μ的灰尘的过滤效果为20%，满足机 房洁净度的要求。
02
性能特点
工作条件：工作电压与频率 ：380V±10 %/50±5Hz； 室外温度范围：标准机组：-20℃~43℃/带选配功能 时：-30℃~50℃，室外/内机落差范围在-5~30m范围内以 及室内/外机之间水平管路的单向长度在60米及以内时可正 常工作（如超出此范围请与我司研发部门联系确认）。
kW kW
kW A kW kg
n. m3/h Pa kW
kW n.
kg/h kW
in in
in in
kW
A
mm mm mm kg
7E1C1
7.6 7.2
1.95 3.5 2.6 3.2
1 2450
30 0.36
2.3 1
3 2.3
CMD4
5/8″ 1/2″
5.5 10.4
650 650 1910 142
ᄰଌᤌଌ Direct connection 4
RS485-RS232 Converter 34ጳ 34%BUBDBCMF
34ጳ 34%BUBMJOF ӭᤰ345$1*1ᣁ૱٨ Single port RS485-TCP/IP converter
机组结构紧凑，占地面积小，重量轻，便于搬运和在狭小 的空间中安装。
某公司产品系列特点介绍
风机
2021/2/2
室内风机：
形式：直连式无蜗壳离心风机 品牌：EBM 送风电机形式：三相EC电机
OPTIMA系列精密机房空调为我公司为 了满足节能高效专门研制的一个系列产品， 产品结构充分考虑到EC风机的特点，风机倾 斜安装，风量大，最大限度的利用了EC风机 节能的优势，且EC风机均为国际知名品牌 EBM、施乐百提供。
32
板式蒸发器——高换热效率
换热通风无气流死角、冷凝水排放顺畅、焊点少泄漏风险低、维护简单方 便、显热比高
采用双曲宽缝波纹翅片及高效 内螺纹铜管，大大强化了热交换
此外，机组内部还预留了空间，用户可以选 用其他形式的加热方式，例如：热水加热或蒸汽 加热。
其他厂家： 同样采用PTC或不锈钢绕片式电加热器，控制 级数有区别，我公司为2级，其他如世图兹为3 级。
17
其它系统配件 知名品牌的干燥过滤器、热力膨胀阀、视液镜和电磁阀。
电器元件 机组主要电器控制件均采用世界知名公司的产品，并且每一个独立负载均配有 磁热保护开关和接触器，以确保机组运行的安全以及部分负载出现故障时，机 组可以继续运行。
12
电极加湿器
2021/2/2
电极式加湿器 我们采用卡乐牌电极式加
湿器，其通过控制加湿罐内的 水位高低和根据电导率大小， 调节并控制蒸汽的输出量。 优点：结构紧凑，加湿量易于 控制；耗电少，适合湿度精度 控制要求高的电子机房。 缺点：对水质有一定要求。
13
电极式加湿器
水是一种导电液体，当有电流 在在电极间通过，以水作为导电介 质，现成闭合回路，其间产生的电 流使水升温到沸点，从而产生出蒸 汽对环境进行加湿。
CAREL
CAREL苏州工厂
室内送风机已含 室内送风机已含
ON ICON 自动清洗 III 产品说明书
AUTO-purge IIIProven solutions for the power industryPrecision Airflow MeasurementAn ON I CON BrandAir Monitor’s AUTO-purge III is designed for applications where the continuous exposure to airborne particulate might impair the measurement accuracy of Air Monitor’s Combustion Air (CA) Station or VOLU-probe/SS array. When activated by an Air Monitor flow transmitter (such as the VELTRON II, MASS-tron II or VELTRON DPT-plus ) or a distributed control system, a combination of valves are operated to introduce highpressure/high volume air to the flow measurement device’s sensing ports for a short duration while simultaneously isolating the transmitter from over-pressurization. This periodic purging assists in maintaining the sensing ports of the total and static pressure manifolds in a clear, unobstructed condition.Product Description• NEMA 4X Stainless Steel Enclosure• Vortex Cooler. Requires 80-100 psi air supply • Enclosure Heater. Requires 120VAC power supply •Viewing WindowPower Capacity • 24VAC • Standard• 24VDC • Low – Model SP • 120VAC • High – Model HCOptional ConstructionDimensional SpecificationsBrass and Copper Construction • All wetted tubing, fittings, and valves constructed of copper and/or brass.• Enclosure is NEMA 4 painted steel.• External connection fittings are stainless steel FPT.Stainless Steel Construction • All wetted tubing, fittings, and valves constructed of 316 stainless steel.• Enclosure is NEMA 4 painted steel.• External connection fittings are stainless steel FPT.Standard ConstructionSequence of OperationAutomatic purging at regular field selectable intervals utilizes short duration, high pressure (up to 125 psig) air to maintain signal lines and the sensing ports of the total and static press ure manifolds in a clean, unobstructed condition. If accompanied with a VELTRON II, MASS-tron II or VELTRON DPT-plus transmitter, the last transmitted process outputs are maintained for the purge cycle. At the start of the purge cycle solenoid piloted spool valves are activated to isolate the transmitter from the process signal lines, followed by the energizing of a separate purge air solenoid valve thatallows high pressure purge air to flow to the measurement station or probe array, forcefully flushing out all particulate contaminants.At the end of the timed purge cycle the purge air valve is de-energized to shut off the supply of compressed air. After a short period to allow the pressures in the signal lines to bleed down to process levels, the spool valves are shuttled to reconnect process signal lines to the attached transmitter and active process measurement resumes.Installation GuideAccumulator Tank (strongly recommended)• Requires coalescing filter, pressure regulator, and checkvalve at the tank inlet. 120 gallons – All CA stations.120 gallons – Multiple VOLU-probes having a combinedlength greater than 10'. 80 gallons – One or more VOLU-probes having acombined length less than 10'.Line from Accumulator Tank to AUTO-purge Panel• 25' maximum length, 1/2" pipe (minimum).• Recommend locating accumulator tank as close aspossible to AUTO-purge Panel.Electrical Power Requirement• 74VA at 24VAC; 28W at 24VDC; 77VA at 120VAC.• 120VAC, 5 amp when an optional enclosure heater isinstalled.Air Requirement• 80 to 175 psig at 20 ACFM, oil and dirt free.Line Size• If the distance from the AUTO-purge Panel to the airflow measuring station or probe array is less than 25', tube size to be 1/2" O.D. with a wall thickness no greater than 0.065".• If the distance from the AUTO-purge Panel to the airflow measuring station or probe array is 25' to 50', tube size to be 3/4" O.D. with a wall thickness no greater than 0.065".• If the distance from the AUTO-purge Panel to the airflowmeasuring station or probe array is greater than 50', tube size to be 1.0" O.D. with a wall thickness no greater than 0.065".Ambient Temperature • 40ºF to 140ºF. For ranges above or below this ambienttemperature, the use of an enclosure heater and/or cooler is required.The VELTRON II ultra-low differential pressure and flow transmitter, with its 0.1% of Natural Span accuracy, is intended for the most critical and demanding industrial applications that require the utmost accuracy and long-term stability. The VELTRON II’s long list of features include: AUTO-purge management; microprocessor based configuration and calibration; four lines of process data display via the graphical LCD; four analog outputs individually configurable for 0-10VDC or 4-20mA; AUTO-zero capability; electronic re-spanning; adjustable digital low pass filter; membrane keypad interface; 10:1 turndown capability; and nine different standard and bi-polar natural spans covering a range of 25.0 to 0.05 Inches w.c.Via the addition of process temperature and pressure compensation, the ultra high accuracy VELTRON II becomes the MASS-tron II multi-variable flow transmitter. For process temperature the input is an analog signal from a remote 4-wire or loop powered tempe rature transmitter with the MASS-tron II having the capability of performing the linearization. The process pressure is measured by means of an internal absolute pressure transducer connected to the transmitter’s static pressure signal input.The CAMM is an ultra-low differential pressure mass flow transmitter designed to convert the low magnitude pressure signals generated by airflow stations or probes - plus process temperature and static pressure inputs - into multiple output signals (4-20mA, 0-5VDC or 0-10VDC) linear to mass flow, temperature, and pressure.When combined with the AUTO-purge III, the CAMM multivariable transmitter becomes theCAMS. Please refer to the CAMS brochure for additional detail on this product.P.O. Box 6358 • Santa Rosa, CA 95406 • P: 800-airflow • F: 707-526-9970 •***********************IBAM TM – Individual Burner Airflow MeasurementThe IBAM TM – Individual Burner Airflow Measurement probe is ideally suited for new or retrofit applications where a reduction in plant emissions and improvement in efficiency can be obtained through accurate measurement of burner secondary airflow. The IBAM TM probe has been designed to accurately measure in the particulate laden, high operating temperature conditions found in burner air passages.CEMS TM – Continuous Emissions Monitoring SystemAir Monitor's CEMS TM – Continuous Emissions Monitoring Systems assist in complying with the Clean Air Act’s stringent emission measurement standards and the requirements of 40 CFR 75. Air Monitor has assembled a cost effective integrated system consisting of in-stack flow measurement equipment and companion instrumentation to provide continuous, accurate,and reliable volumetric airflow monitoring of stacks and ducts of any size and configuration.CA TM – Combustion Airflow Measuring Station & VOLU-probe/SS TM Traverse Probes . Air Monitor's duct mounted airflow measurement devices have beendesigned to accurately and repeatedly measure air mass flow in power plants. The Combustion Air (CA) Station TM includes honeycomb air straightener to accurately measure in shorter straight duct runs than any other flow measurement device. The VOLU-probe/SS TM delivers accurate airflow measurement performance in the form of an insertion probe. Both devices feature Type 316 stainless steel flow sensing arrays.Engineering & Testing Services. Air Monitor offers complete engineering and testing to analyze air and coal deliverysystems. Air Monitor's field testing services use 3D airflow traversing and flow measurement systems for the highest possible accuracy. To ensure cost effective and accurate solutions, Air Monitor Power has full scale model fabrication and certified windtunnel testing is used to develop application specific products that will measure accurately where no standard flow measurement can.VOLU-probe/SS TM Stainless Steel Airflow Traverse ProbesMulti-point, self-averaging, Pitot-Fechheimer airflow traverse probes with integral airflow direction correcting design. Constructed of Type 316 stainless steel and available in externally and internally mounted versions for harsh, corrosive or high temperature applications such as fume hood, laboratory exhaust, pharmaceutical, and clean room production and dirty industrial process applications.125-501-10 (03/20)Precision Airflow MeasurementAn ON I CON BrandCAMS TM – Combustion Airflow Management Systems .The CAMS TM – Combustion Airflow Management System has been designed to reliably and accurately measure airflow in combustion airflow applications. The CAMS TM contains the microprocessor based instrumentation to measure the airflow and manage the AUTO-purge. The AUTO-purge is a high pressure air blowback system that protects the duct mounted flow measurement device from any degradation in performance due to the presence of airborneparticulate (flyash).。
- 1、下载文档前请自行甄别文档内容的完整性，平台不提供额外的编辑、内容补充、找答案等附加服务。
- 2、"仅部分预览"的文档,不可在线预览部分如存在完整性等问题,可反馈申请退款(可完整预览的文档不适用该条件!)。
- 3、如文档侵犯您的权益，请联系客服反馈,我们会尽快为您处理(人工客服工作时间：9:00-18:30)。
顶部送风机组标准机外余压50Pa，应用于需要接风管送 风的场所，使室内温度分布更加均匀，室内机安放位置也 更灵活。
3种当地电脑直接联接监控方式 3种局域网联接监控方式 4种远程无线网络监控方式
ጳᤌଌவर ጳᤌଌ
8JSFMFTTጳᤰηᎪፏ 345$1*1ጳႀ٨
ጳᤌଌ ጳᤌଌ
ጳႀ٨ຫໍສະໝຸດ (4.ረүᤰηᎪፏጳᤌଌ
(4.ᆁηവڱ
(4.വڱ
(4.ጳᤰηᎪፏ
ᄣႃᑨ߷ᜉ5$1*1ӵἻ 34ӵἻ34ӵἻࣳ߷ᜉ *OUFMMJ7JTJPO1MVTᄣᣄ͈
7E1C0 12E1C0 15E1C2 18E1C2 22E1C3 25E1C3 30E1C3
O
O/U/DL/TP
kW
7.1
13.1
15.4
18.3
22.2
25.4
30.2
kW
6.3
11.8
14.2
16.8
20.4
23.4
27.8
kW
7.6
13.7
16.0
18.7
22.6
25.9
30.6
kW
6.8
12.2
2.3
2.3
3.8
3.8
3.8
6.0
6.0
CMD4×1 CMD5×1 CME8×1 CME8×1 CME8×1 CME10×1 CME10×1
380V/3ph/50Hz
kW
5.0
9.7
11.8
12.9
16.9
18.2
19.5
A
10.5
18.0
21.1
23.0
30.0
32.7
34.6
in
3/4″
3/4″
15.0
17.4
21.0
24.1
28.5
全封闭涡旋式
kW
1.7
3.5
3.7
4.6
5.2
5.9
6.9
A
3.1
5.6
6.5
8.0
9.7
11.2
12.7
kW
1.8
3.6
3.8
4.8
5.3
6.0
7.1
A
3.3
5.7
6.7
8.2
9.9
11.5
12.9
n. m3/h Pa kW
A
双进风离心风机
1
1
1650
2630
型号识别
DATACOOL
.
O U DL TP
7
C0
. DXA 10 E1 C2 R407 . XXX
...
C3
变形设计代号,使用三位字母或 阿拉伯数字表
分隔符：“.”
制冷剂的名称 缺省= R22制冷剂 R407=R407c 制冷剂
机柜规格编号: 本系列机组使用3种机柜: C0，C2，C3
压缩机类型和数量： E1：机组配用1台全封闭涡旋式压缩机
安静清洁 DATACOOL系列产品的空气过滤器采用可清洗式合成纤 维过滤器，过滤效率为G4，即粒径为5μ的灰尘的过滤效 果为80%，粒径为1μ的灰尘的过滤效果为20%，满足机 房洁净度的要求。
美观紧凑 DATACOOL系列产品面板、底座、内框架的颜色均为黑 色，高度和厚度与标准机柜相近，设计风格与机房内的设 备协调，整体效果更为美观。
— ● ○ ○ — ● ○ ○ ○
30E1C3
— ● ○ ○ — ● ○ ○ ○
注：以上配置不适用于C0机柜，如需C0机柜型号产品配置，请咨询公司技术人员。
05
智能控制
微电脑控制系统对压缩机、风机、加湿器、电加热器等所有部件进行智能化控制及保护。 远程监控系统可以与该机组方便地连接，实现对机组各部件的远程实时监控，并存储机组运行的历史数据。 该产品可以通过如下多种方式实现远程监控：
900 750 1910 255
900 750 1910 290
1300 750 1910 370
1300 750 1910 460
1300 750 1910 490
⑴ O ：上送风（前上百叶风口直接送风） ；D：地板下送风；DL：置换送风；TP：顶部送风； ⑵ 指回风干球温度24℃，湿度50%，室外环境干球温度35℃的情况下； ⑶ 指回风干球温度28℃，湿度40%，室外环境干球温度35℃的情况下； ⑷ 选配件，本参数表为默认加湿/加热量。如果需要选配其他加湿量/加热量，请参考“电加热/电加湿配置表”； ⑸ 具体参数，请查阅风冷冷凝器样本，CMD冷凝器只提供立式安装； ⑹ 最大运行功率和电流指的是：按上述参数表配置，在最高使用环境温度45℃，机组运行在除湿模式并且电加热满载补偿 运行的情况下。
电源主开关 压缩机、风机、电加热、加湿等每个负载的微型断路器 压缩机、风机、电加热、加湿等每个负载的接触器 辅助控制电路及微电脑控制器用的变压器
可选配置 三相EC无蜗壳后向离心电机 可选使用R407c制冷剂的机组 -20℃以下低温启动组件 过滤器风压差保护开关 送风温度传感器 送风静压传感器 高度可调的安装支架 地板积水报警组件 RS232通讯卡 RS485通讯卡 Pcoweb 通讯卡 时钟卡 通讯协议转换器
机组结构紧凑，占地面积小，重量轻，便于搬运和在狭小 的空间中安装。
安全可靠 DATACOOL系列产品使用的关键部件，如压缩机、风 机、膨胀阀、控制器等均选用国际知名品牌，符合主要国 际工业标准，保证机组安全可靠运行。
机组控制系统具有三级密码保护，可有效防止未经授权者 对机器进行误操作，保证机组控制的安全性。
机组带有全面的保护和报警，保证机组安全可靠运行，降 低机组的故障概率，包括制冷系统高压/低压保护、压缩 机过热保护、加湿器保护、加热器过载保护、风机电机保 护、温度过高或过低保护、过滤器堵塞报警等。
04
产品配置
标准配置 钢板折弯成型表面喷涂黑色的底座、内框架及顶框架 钢板折弯成型表面喷涂黑色的面板及隔热隔音层 涡旋式压缩机 三相AC无蜗壳后向离心电机 铜管铝翅片式蒸发器 外平衡热力膨胀阀 视液镜 干燥过滤器 制冷剂储液器 电极式加湿器，多档加湿量可选，见“电加热/电加湿配置表” 不锈钢绕片式电加热器，多档热量可选，见“电加热/电 加湿配置表” G4空气过滤器 回风温度湿度传感器 风机风压差保护开关 微电脑控制控制系统 电源相序控制器(仅用于3相电源机组) 冷凝压力连续控制系统 微电脑控制系统 电气控制盘，包括：
名义制冷能力（单位为kW）
制冷方式：DXA表示直接蒸发风冷式制冷
分隔符：“.” 送风方式： O：上送风方式，从机组前上部送风； U：下送风方式，从机组底部送风； DL: 置换送风方式，从机组前下部送风； TP: 顶送风方式，从机组前下部回风； （U/DL/TP仅适用于C2、C3机柜）
分隔符：“.”
产品系列名称： DATACOOL：DATACOOL系列中心型机房专用空调，简写为：DATA
N2
ࡍ۫Ꭺᤌଌ &UIFSOFUᎪፏጳ
34ጳ
N16 N1 N2
N16
ܳԼጸᄰଌᤌଌ N1
ᄰଌᤌଌ Direct connection 3
ᄰଌᤌଌ Direct connection 4
34ጳ ӭᤰ345$1*1ᣁ૱٨
&UIFSOFUᎪፏጳ
34ጳ
34ጳ
电加热/电加湿配置表
机组型号
项目
6
电加热量
9
(kW)
12
13.5
5
加湿量
8
10
(kg/h)
13
15
15E1C2
● ○ — — ● ○ — — —
18E1C2
● ○ — — ● ○ — — —
注：“●”表示标准配置，“○”表示可选项，“—”表示无。
22E1C3
— ● ○ ○ ● ○ ○ ○ ○
25E1C3
举例：D A T A C O O L.O.D X A15E1C2:表示该机组是一台D A T A C O O L系列机房空调机组，上送风方式，直接蒸发风冷式制 冷，与远置式风冷冷凝器配套使用，名义制冷量为15kW。机组使用1个压缩机，机柜规格为：C2.
02
工作范围与控制精度
工作范围 室外环境温度: -15℃～45℃；配置低温运行的选配件或方案时，可 到-40℃ 接管长度： 气管加液管总长水平等效长度30米 (超过上述范围请向厂家或经销商咨询确认相关安装方案) 接管高度: 室外机高于室内机：最大允许落差20米； 室外机低于室内机：最大允许落差5米。 (超过上述范围请向厂家或经销商咨询确认相关安装方案)
工作原理
03
产品特点
节能高效 节能高效是D A T A C O O L系列产品设计理念的核心。通过 选配高能效部件（如高效压缩机和风机）并对制冷系统各 部件的优化配置，使整机能效比高达2.9以上。
可选节能运行模式 在该产品中集成了两种运行模式，即：标准运行模式和节 能运行模式。对温湿度控制要求较高时，可以选择标准运 行模式，如果对温湿度控制精度要求不高的话，就可以选 择节能运行模式，可以获得10%以上的节能效益。
3/4″
3/4″
3/4″
3/4″
3/4″
in
1/2″
1/2″
1/2″
1/2″
1/2″
1/2″
1/2″
喇叭口螺纹连接
焊接连接
in
5/8″