胶带产品说明书A样本
钢筋胶带护套产品说明书
Note:Tape armour must bere-trimmed at 90° to thevertical axis of the cableafter it has been spread,to ensure that the fullface is correctlypresented.IArmour / braidIIIShroud option621354564214321 3213Braid 'X',Flat Steel Wire 'Y',Steel Tape 'Z'Ring PositionSWAPositionGeneral identification ring orientation for:Reversible Armour Clamping Ring (RAC)Gland Type: ICG 653/UNIVExdb IIC Gb / Exeb IIC Gb / Extb IIIC DbBaseefa06ATEX0058X II 2 GD IP66IECEx BAS06.0015XIEx 14.0272XEAC ТC RU C-GB.ГБ05.B.00750c CSA us No: 1024328Class 1 Zone 1 AExd IIC, AExe II,Zone 21 AExtDClass 1 Div 2 ABCD, Class II Div 2 Groups EFG, Class IIICNEx12.3448XCertification DetailsOperating temperature range -60°C +80°CNote: Armour cable acceptance sizes are marked onthe clamping ring.IMPORTANT: The arrowhead indicating thecorrect armour thickness or type should pointtowards the equipment1. Backnut2. Middle Nut3. Reversible Armour Clamping Ring (RAC)4. Armour Spigot5. Rubber Pot6. Entry (with captive deluge seal)Cable Preparation Gland PreparationAStrip Cable to suit equipment as shown above andexpose the armour/braid 'I' removing all cable fillers.'I' = 20mm for cable gland sizes Os to A'I' = 25mm for cable gland sizes B to C2'I' = 32mm for cable gland sizes D to F'II' to suit equipment.If required, fit shroud.See Notes re. Drain Wires.BPush the cable through the armour spigot ④. Spreadarmour/braid over the armour spigot ④ until the endof the armour/braid is up against the shoulder of thearmour cone. Position the armour clamping ring ③.CRemove the rubber pot ⑤ from the entry ⑥. Placethe entry ⑥ over the armour spigot ④. Move thesub-assembly ① and ② up to meet the entry ⑥.AI 301 - Issue W / Page 1 of 4AI 301 / Issue W - 06/17 Assembly Instructions for cable gland:ICG 653/UNIVProduct supplied may differslightly from that shown.Images are for illustrationpuproses only.CompoundTape35mmRemove surplus compoundRemove surplus compoundCompound5465621242663142AI 301 - Issue W / Page 2 of 4When handling this material, the gloves supplied must be worn. The epoxy compound is supplied in the form of a two part package. These should be mixed into the ratio of 1:1 until both colours have blended into one, without any streaks. Rolling and folding is the most satisfactory method of obtaining an even blend. Once mixed, the compound must be used within 30 minutes. After this time it will begin to stiffen. The compound should be kept at an ambient temperature of no less than 20°C prior to using. At lower temperatures it becomes difficult to mix. Should any compound come into contact with the skin it should be cleaned off with skin cleaner and not allowed to dry on the skin. Only compound for immediate terminations should be mixed.The mixing and installation of the compound at an ambient temperature below 4°C is not recommended due to extended curing periods.The storage of the compound shall be at temperatures between 5°C and 30°C.DHold the entry ⑥ in position with a spanner/wrench to prevent rotation. Hand tighten the middle nut ② onto the entry ⑥ and turn a further half to three quarters of a turn with a spanner/wrench.EUnscrew the middle nut ② and visually inspect that the armour/braid has been successfully clamped between the armour spigot ④ and the armourclamping ring ③. If armour/braid not clamped repeat assembly.FRemove the entry ⑥, spread the cable cores out for the compound packing. Pack the compound between the cores shown. See notes below and Fig. 7 for compound preparation.GWith all gaps and voids filled, bring the conductorsback together and pack more compound around the outside of the conductors. Tape the conductors together to prevent disturbance of the compound seal. Pass the rubber pot ⑤ over the armour spigot ④ and remove any surplus compound. from the top of rubber pot ⑤ and the joint face as indicated.H Replace the entry ⑥ over the rubber pot ⑤ ensuring that compound does not cover the end of ⑤.ILocate and hand tighten the sub-assembly ① and ② to the entry ⑥.IMPORTANT: The conductors must not be moved for a minimum of four hours.EPOXY COMPOUND PREPARATION1.0 INSULATING DRAIN WIRES WITH HEAT SHRINK OR COLD SHRINK TUBING 1.1 Fold back the armour / braid and bend it to right angles from the inner sheath. 1.2 Remove foils and tape level with the outer sheath, exposing the drain wires and insulated conductors. Cut back a further 10mm of inner sheath.1.3 Pass 100mm length of heat shrink or cold shrink tubing over the drain wire until it comes into contact with the foils, then shrink the tubing evenly down onto the drain wireso that no air pockets occur.1.4 To insulate the joint between the foils and the tubing a suitable piece of 10mm long shrink tubing or neoprene stretch tubing or a 10mm wide lap of PVC tape may be used. 1.5 After completing 1.1 to 1.4 on each drain wire, lay the armour / braid parallel to the cable, if applicable, then carry out instruction B.DRAIN WIRE PREPARATIONThe following instructions are the various BASEEFA approved methods of passing drain wires etc. through the compound barrier and should be followed if permitted by cable installation specifications.2.0 INSULATING DRAIN WIRES / SCREENS WITH SEPARATE INSULATED CRIMPED CONDUCTORS OR SOLDERED CONNECTION 2.1 Fold back the armour / braid and bend to right angles from the inner sheath. 2.2 Remove a further 15mm of inner sheath (See Fig. 1). 2.3 Unravel one or two groups of wires from the screen wires, then remove the remainder of the screen wires (See Fig. 2). 2.4 Twist the group of screen wires into a pigtail and cut to 15mm long. 2.5 Crimp an insulated conductor to the pigtail wih a suitable insulated butt ferrule (or soldered connection), leaving enough length of the insulated conductor to enable theremote end to be connected to the earth terminal in the equipment. (See Fig. 3). Note: There shall be a minimum of 10mm of compound on both ends of the crimped /soldered joint.2.6 To insulate the joint between the screen wires and the insulated conductor, place one lap of PVC insulating tape over the exposed metallic joint. 2.7 After completing 2.1 to 2.6 on each drain wire, lay the armour / braid parallel to the cable. Then carry out instruction B.3.0 INSULATING DRAIN WIRES WITH INSULATING VARNISH OR PAINT 3.1 Fold back the armour / braid and bend it at right angles from the inner sheath. 3.2 Remove the foil and tape level with the inner sheath exposing the drain wires and conductor pairs. 3.3 Cut back a further 10mm of inner sheath (See Fig. 4). 3.4 Spray or paint the drain wires with insulating varnish or paint, then leave to dry (See Fig. 5) 3.5 To insulate the foil ends a suitable piece of 10mm long shrink tubing or neoprene stretch tubing or a 10mm wide lap of PVC tape may be used (See Fig. 6).3.6 After completing 3.1 to 3.5 on each drain wire, lay the armour / braid parallel to the cable. Then carry out instruction B.Outer SheathArmour / braidArmour / braid15mm10mmInner Sheath One or two groupsof screen wiresInsulated ConductorCrimp or SolderScreen WiresInner Sheath FoilsDrain WireInsulatedDrain WireSleevingFig. 1Fig. 2Fig. 3Fig. 6Fig. 5Fig. 41652612AI 301 - Issue W / Page 3 of 4JAllow the compound to cure. (See Fig. 7 for Curing Times). Untighten the sub-assembly ① and ② from the entry ⑥ to enable inspection.The rubber pot ⑤ may be removed for inspection to ensure that the packing is satisfactory.Add further compound if necessaryKRe-assemble the rubber pot ⑤ and the entry ⑥. Tighten the sub-assembly ① and ② to the entry ⑥ until resistance is felt and add half to three quarters of a turn to ② with a spanner / wrench. Tighten the backnut ① to form a seal around the cable, then tighten a further full turn using a wrench / spanner. Ensure that the middle nut ② does not rotate when tightening the backnut. Ensure that the deluge seal is pulled down into position. Locate the shroud over the cable gland, if applicable.1289080706050403020100S h o r e H a r d n e s sTime (Hours)40 ºC 25 ºC 4 ºC416Epoxy CompoundCure Time Vs. TemperatureFig. 7CABLE GLAND SELECTION TABLEEntry ThreadSize MetricSize RefNPTAcross Flats C o m p r e s s e d L e n g t hAcross CornersHexagon Dimensions O A B C C2D E FM20M20M25M32M40M50M63M75½" - ¾"2" - 2½"2½" - 3"11.016.221.926.337.147.859.012.518.424.729.741.753.566.2/65.326.532.539.550.560.670.888.0104.0Inner Sheath/CoresOuter Sheath Cable Acceptance Details8.910.0Min.Max.9.512.516.922.028.036.046.057.016.020.526.033.041.052.665.378.00.8/1.250.8/1.251.25/1.61.6/2.01.6/2.01.8/2.51.8/2.51.8/2.50/0.8Os M20½"½"26.567.067.073.678.082.488.792.799.467.0M a x i m u m L e n g t h83.084.091.098.0100.0116.0124.0122.083.08.910.0 5.512.00.8/1.250/0.80/0.8 0/0.70/0.70/0.70/1.00/1.00/1.0¾" - 1"1" - 1¼"1¼" - 1½"1½" - 2"12153042608010012012ATEX Max. No. of Cores Max.Over Cores Max. Inner Sheath Steel Wire Armour/Tape/BraidOrientation2Orientation 124.030.036.046.055.065.080.095.024.0ACCESSORIES:Before cable gland assembly or stripping of the cable gland assembly, consideration should be given to any cable gland accessories that may be required, such as: -● Shroud, to offer additional corrosion protection.● Locknut, to secure cable glands into position.● Sealing washer, to offer additional ingress protection of the enclosure at thecable gland entry.● Earthtag, to provide an external armour / braid bonding point.● Serrated washer, to dampen any vibrations that may loosen the locknut orcable gland assembly.SCHEDULE OF LIMITATIONS - Baseefa ATEX / IECEx:1. These glands are suitable for use within an operating temperature range of-60°C to +80°C.2. When the gland is used for increased safety, the entry thread shall besuitably sealed to maintain the ingress protection rating of the associated enclosure.AI 301 - Issue W / Page 4 of 4EU Declaration of Conformity in accordance with European Directive 2014/34/EU Manufacturer: Hawke InternationalAddress: Oxford Street West, Ashton-under-Lyne, OL7 0NA, United Kingdom.Equipment: Group II Barrier Cable Glands Type: ICG 653/UNIVProvisions of the Directive fulfilled by the Equipment:Group II Category 2GD Exeb IIC Gb, Exdb IIC Gb, Extb IIIC Db – IP66Notified Body for EU-Type Examination: SGS-Baseefa 1180 Buxton UK EU-type Examination Certificate: Baseefa06ATEX0058X Notified Body for production: SGS-Baseefa 1180 Buxton UK Harmonised Standards used:EN 60079-0:2012+A11:2013, EN60079-1:2014, EN60079-7:2015, EN60079-31:2014.On behalf of the above named company, I declare that, on the date the equipmentaccompanied by this declaration is placed on the market, the equipment conforms with all technical and regulatory requirements of the above listed directives.………………………………….A. Tindall Technical Manager………………………………………Ti d ll● The compound may be adversely affected by some solvent vapours. If such vapours are likely to be present in the vicinity of the cable gland in service, suitable precautions may be necessary. (Contact Hawke's Technical Dept).● The compound cures at a Shore D hardness of 85, when it can be handled. The compound when fully cured is suitable for use at a temperature range of -60°C to +80°C.NOTES - c CSA us:1. Class 1 Division 2 suitable for Marine Shipboardapplications only according to CSA Standard 245 andIEEE45 / IEC 600092-353 Standards, or certified equivalent, for use on Shipboards and Offshore Rigs / Platforms only.2. Glands must comply with the Canadian Electrical Codeand National Electric Code requirements for threaded entries.3. For Exe applications, a sealing washer or thread sealantmay be required between the enclosure and the gland to maintain the IP rating of the enclosure.4. Drain wires and earth screening may pass through thecompound barrier using one of the methods which are details in this assembly instruction; heat shrink or cold shrink tubing, or addition of an insulated crimped or soldered conductor or insulation by varnish or paint.5. This cable gland may only be installed when temperatureis above +4°C. After completion of the installation, the assembly is then suitable for -60°C to +80°C.。
Nitto D9605系列双面胶带说明书
Page 1/2 Product:Product group:General descriptionNitto D9605 series are double-coated tapes with a polyester carrier coated with an aggressive acrylic adhesive used for mounting of different types of plastics.ConstructionCharacteristicsD9605 series are heavy duty multi-purpose double-coated tapes with a high adhesion level on different substrates such as plastics, foams and metals. The tapes are suitable for rough surface bonding.The PET carrier provides dimensional stability resulting in reduced elongation and shrinkage.D9605 series are available in bobbin shape.ApplicationNitto D9605 series are used for mounting decorative profiles in furniture industry (trim mounting), cable ducts. Available in bobbin shapes designed for continuous application process.Suitable for mounting price information holders and plastic parts in sign & nameplate markets for marketing devices (Point Of Sales).Features- high adhesion on different substrates & rough surfaces - high temperature resistance - high holding power - easy processing - bobbin shape - RoHS compliant- Modified acrylic adhesive - Polyester carrier- Modified acrylic adhesive - Release linerEdition: September 2013D9605 series Double Coated TapesGeneral conditions of use and precautions: The properties of the product might be adversely affected by various elements such as composition, condition and surface of and impurities in or on the substrate, temperature and humidity during storage and the surrounding environment at and after application and time of exterior use.When the product is used in combination with another material or process, the user shall assure the compatibility of the product in such combination and whether this combination results in the expected performance. The same principle applies in the event of product use in extreme conditions or circumstances, whether at or after the moment of application, including extended exposure to sunlight or extreme temperatures and pressure. Packaging, transport and storage:During transport and storage the product should always be protected against direct sunlightand extremes in temperature and humidity and contained in its original packaging. Once removed from its packaging, it should be promptly applied and remain shielded from direct sunlight and extreme temperature as well as protected against dust and other impurities.Liability:Except for its wilful misconduct, Nitto Europe’s liability shall be limited to a replacement, a reimbursement or an additional delivery of the product, and shall not exceed the purchase price of the products. In no event shall Nitto be liable in respect of any indirect or consequential damages, including loss of profits.The above limitations of liability shall equally apply if Nitto Europe has assisted in any manner with the selection, treatment or application of the product. Product information:This datasheet provides a general description of the product properties and application scope. Full technical details in connection with this product are presented in the customer product specification, which is available upon request.Please be advised that the information reflected in this datasheet is subject to change and the product described herein may be modified or discontinued without notice.For your local Nitto Europe sales office, please visit our web site: Copyright © 2013 NITTO EUROPE NV. All rights reserved.Nitto Europe NV has obtained following certificates:- ISO 9001- ISO 14001- ISO/TS 16949Please check our website for applicable scopeIf you require additional information on technical properties and application as well as product sampling or testing, please contact your local Nitto Europe sales office.Edition: September 2013Code: DS/01.11/E4 D9605 series ENG This datasheet replaces all previous versionsTechnical PropertiesGeneral physical propertiesTypical Value Test MethodAdhesive type Modified acrylic adhesiveTape thickness* 0.220 mm EN 1942Release liner D9605: Siliconised havana paper (90 g/m²)D9605S: Siliconised white PE coated paper (125 g/m²)Carrier type Polyester (0.050 mm)Adhesion to BA steel 2000 cN/20mm EN 1939Release value 30 cN/50mm Nitto Europe Test MethodStatic shear 1 mm/3h EN 1943Transport and storage conditions Temperature 15 to 30°CRelative humidity 40 to 75% RH* Tape thickness = Total thickness without linerDetails from the test methods are described on the customer product specification.Performance propertiesAdhesion in cN/20mm EN 1939PMMA PC ABS PP Glass2000 2300 1800 700 2300Weight Added Peel Off (WAPO) 2 h at 60°C, width 20mm, 100gPP 16 mm/2h ABS 13 mm/2h BA 3 mm/2hDynamic Shear 350 N/4cm² Tested after 15 min., 300mm/min.Saft test (Shear Adhesion Failure Temperature) 185 °C +0,5°C/min., 15x15mm, 200gWarrantyThe product is guaranteed to be free from defect in material and workmanship at the time ofdelivery and will be suitable for use for a period of 6 months thereafter, subject to the conditionsset out herein.Application guidelines- Keep the tape in its original packaging until use.- For optimum results, an even rub down pressure must be applied to the taped area to createthe best possible adhesion between tape and the substrates.- Remove the liner prior to usage.- The tape should be applied to clean and dry surfaces.- The best application conditions are obtained at a temperature between 15 °C and 40 °C.Double Coated Tapes - D9605 seriesPage 2/2。
3M VHB Tape产品系列说明书
70-0705-7616-3 (2/02)Limitation of Remedies and Liability: If the 3M VHB Tape is proved to be defective within the warranty period stated above, THE EXCLUSIVE REMEDY , AT 3M’S OPTION, SHALL BE TO REFUND THE PURCHASE PRICE OF OR TO REPAIR OR REPLACE THE DEFECTIVE 3M VHB TAPE. 3M shall not otherwise be liable for loss or damages, whether direct, indirect, special, incidental, or consequential, regardless of the legal theory asserted, including negligence, warranty, or strict liability.Warranty: 3M warrants for 24 months from the date of manufacture, that 3M VHB Tape will be free of defects in material and manufacture. 3M MAKES NO OTHER WARRANTIES, EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO, ANY IMPLIEDWARRANTY OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE.This warranty does not cover damage resulting from the use or inability to use 3M VHB Tape do to misuse. workmanship in application, or application or storage not in accordance with 3M recommended procedures. Important Notice: User is responsible for determining whether the 3M product is fit for a particular purpose and suitable for user’s method of application. Please remember that many factors can affect the use and performance of a 3M product in a particular application. The materials to be bonded with the product, the surface preparation of these materials, the product selected for use, the conditions in which the product is used,and the time and environmental conditions in which the product is expected to perform are among the many factors that can affect the use and performance of a 3M product. Given the variety of factors that can affect the use and performance of a 3M product, some of which are uniquely within the user’s knowledge and control, it is essential that the user evaluate the 3M product to determine whether it is fit for a particular purpose and suitable for the user’s method of application.。
TDUX胶带系统产品介绍说明书
TDUXI N S T A L L A T I O N I N S T R U C T I O N Inflatable Duct Sealing SystemFigure 26.0 Installation Procedures6.1 One Cable in Duct1.Clean 4” of duct and the cable sheath with a wet cloth. (Figure 3)2.For ease of installation, lubricate at least 6” of cable sheath with supplied lubricant or company approved lubricant. (Figure 4)3.Remove the protective paper from the sealing strip on the outside surface of the TDUX duct seal and lubricate the strip abundantly. If the ducts are made of concrete or polyethylene,lubricate the outside surface of the TDUX seal as well. (Figure 5)4.Remove the protective paper from the sealing strip on the inside surface of the TDUX duct seal and lubricate the strip abundantly.(Figure 6)5.Lubricate the filling tube on the TDUX duct seal. (Figure 7)6.Wrap the TDUX duct seal around the cable and slide completely into the duct. Be sure that filling tube faces out of the duct and center cable in duct prior to inflation, if possible.(Figure 8)Figure 3Figure 5Figure 6Figure 7Figure 8Figure 9Figure10Figure 11Figure 13 illustrates several different multiple cable configurationsand branch clip locations .1.Clean cables and lubricate duct as in 6.1, Steps 1 and2.2.Open clip wings on one side. Lubricate the wings abundantly to ensure that they do not stick together.(Figure 14)3.Remove one protection paper and lubricate the larger surface of the clip wing.(Figure 15)4.Repeat steps 2 and 3 for the other clip wings. Removeprotection paper only after lubricating at least one wing side.(Figure 16)5.Lubricate the cables generously where the cables come together. (Figure 17)6.Insert the clip between the cables, making sure that there is only one cable between each clip wing (see figure 13). Make sure that the central part of the clip is positioned where the cables come together (mark flush with duct entrance).(Figure18)Figure 13Figure 14Figure 15Figure 16Figure 177.If necessary, use a tie wrap to hold the clip in place. Cut off excesstie wrap and position the head between the cables. Tape all cables together near the duct. (Figure 19)plete steps 3-10 in section 6.1.6.3 Square DuctSealing cables in a square duct requires the use of a TDUXsquare duct kit in addition to the standard TDUX ductsealing system. Mastic components and instructions fortheir use are included in that kit. For sealing more than onecable in a square duct, a TDUX CL sealing clip kit will alsobe required (see section 6.2).6.4 Empty DuctClean and lubricate the duct, then lubricate and install the appropriate size TDUX duct seal inside the empty duct.Inflate the TDUX duct seal as in step 7-10 of section 6.1.7.0 Removal1.Deflate the TDUX duct seal by piercing with a screwdriver.Note: Be careful not to damage the cable. (Figure 20)2.Pry the TDUX duct seal away from the duct and from the cablesheath with a blunt tool. Spray lubricant into the released areas so that the TDUX duct seal does not stick to the duct during removal. (Figure 21)3.Pull the TDUX duct seal out of the duct with a pair of pliers.(Figure 22)4.If necessary, remove tape (and tie wrap) from the cable bundle.Spread cables and apply lubricant where the cables come togeth-er. Remove as much clip core and sealant as possible with a pair of pliers.(Figure 23)Figure 19 Figure 21 Figure 22Figure 23Technical Assistance Center (TAC)Tel.: 800.830.5056Email:************************** The information given herein, including drawings, illustrations and schematics which are intended for illustration purposes only, is believed to be reliable. However, CommScope makes no warranties as to its accuracy or completeness and disclaims any lia bility in connection with its use. Commscope obligations shall only be as set forth in CommScope Standard Terms and Conditionsof Sale for this product and in no case will CommScope be liable for any incidental, indirect or consequential damages arising out of the sale, resale, use or misuse of the product. Users of CommScope products should make their own evaluation to determine the suitability of each such product for the specific application.© 2016 Commscope inc. All Rights ReservedThis product is covered by one or more U.S.patents or their foreign equivalents. For patents, see /ProductPatent/ProductPatent.aspx。
黏性胶涂Apply 型号的产品说明书
We supply the highest quality, most extensive range in the industry. All of our tips are certified silicone-free to ensure any fluids dispensed from them will not be contaminated with silicone mould release agents.Features and Benefits• Burr-free, flash-free and silicone-free parts• All parts batch coded for traceability and process control• Double-helix luer lock for secure, leak-free tip attachment• UV filtered plastic hubs for use with UV-cure adhesives• Consistency in products and qualityPrecision TE Tips Stainless steel tips with polypropylene hubs general purpose designed to handle a wide range of fluids and dispensing applications.Smooth Flow Tapered Polyethylene tips for applying medium to high viscosity materials - especially thick or particle filled materials such as epoxies, RTV silicone’s, braze and solder pastes.Flexible Polypropylene shafts that fit into hard-to-reach areas and soft not to scratch sensitive substrates.Angled Bent tips for hard-to-reach areas in 45 and 90 angle bends.Teflon PTFE-lined and Clear Teflon tips for handling Cyanoacrylate adhesives.Brush For spreading glues, greases, coatings and primers. In soft or stiff bristle.TS Tips Crimped where the polypro hub joins the stainless steel shaft for resistance to solvents.Aluminium and All-Metal tips for precision and accuracy when dispensing aggressive chemicals and solvents.General Purpose dispensing tips for most fluids and most applications.Tips designed for dispensing thick pastes, gels, sealants, and compounds.Flexible tips for hard to reach places and adhesives that are reactive.Flexible tips for hard to reach places and for adhesives that are reactive.Tips that are designed to dispense Cyanoacrylate adhesivesTips that are designed to dispense Cyanoacrylate adhesivesTips that are designed to dispense solvents, chemicals & aggressive gluesTips that are designed for use on precision automated dispense robots.Adhesive Dispensing LtdLuer Lock TipsTips for spreading, coating and priming parts.Precision Dispensing Tips For complete assistance with tip selection, please contact us on +44 (0) 1908 686660 or email us at **************************.uk . We ship products direct from stock. All tips are certified silicone-free and are industrial grade safe. 。
阿尔科林Peel 'n Seal自凝缝造缝胶带说明书
ALCOLIN PEEL ‘N SEALSELF ADHESIVE WATERPROOFING TAPEDescriptionAlcolin Peel ‘n Seal is a self-adhesive polymer modified bitumen adhesivetape backed with a durable aluminium foil that creates a watertight seal onalmost any surface. It is ready to use and ideal for sealing and repairing ofmetal sheeting, water tanks, down pipes and gutters. It is supplied in rollsthat are interleaved with a disposable release film.Features & Benefits∙Instant water-tight seal – impermeable to moisture and water vapour∙Quick effective repairs∙Excellent resistance to weathering∙Durable, remaining permanently flexible∙Strong aluminium foil backingApplicationsSealing and repairing of holes, gaps and overlaps in galvanized roof sheeting, valley gutters, down pipes, roof screws, flashings, parapets, window frames, pipe vents, ridging, metal boxes, galvanized buckets, water tanks, sheds and kennels.AdhesionGalvanised steel, aluminium, stainless steel, concrete, cement plaster, polycarbonate, PVC, glass, and wood.Limitations∙Not suited for polypropylene, polyethylene and Teflon.∙Not suitable for sealing of high-pressure systems.Safety instructionsAlcolin Peel ‘n Seal is non-toxic, however, it is advisable to wear gloves in order to avoid direct skin contact. If the product comes in contact with skin or eyes, flush thoroughly and immediately with water. If irritation continues, seek medical attention. Keep out of reach of children! Refer to our Safety Data Sheet for further toxicological information and comprehensive handling instructions.Surface preparationSurfaces to be bonded must be clean, structurally sound, dry and free from dust, dirt, oil, rust and loose material. Smooth non-porous surfaces such as metals and plastics should degreased with a solvent such as acetone or thinners. Any gaps should be filled prior to application. Poor surface preparation may result in lifting and delamination of the tape.Directions for use∙Ensure that surfaces are prepared as above.∙Unroll the tape and measure the correct length for the area to be sealed.∙Cut the tape ensuring a 40mm overlap.∙Allow the tape to warm in the sun before application.∙Peel the release paper back from one end and press the tape firmly onto the surface.∙Removing the backing tape as you proceed.∙On angles and grooves press firmly into the angle or groove first.∙For a smooth finish, press tape with a rubber hand roller, working from the center outwards, remove any air bubbles and creases ensuring firm contact is made with the surface.∙The aluminium foil backing must not be removed.Storage stabilityStore in cool place below 25°C. Recommended storage is 24 months.Product packaging∙Alcolin Peel ‘n Seal 2.5m x 50mm ∙Alcolin Peel ‘n Seal 2.5m x 75mm ∙Alcolin Peel ‘n Seal 2.5m x 100mm ∙Alcolin Peel ‘n Seal 5m x 100mm ∙Alcolin Peel ‘n Seal 5m x 150mm ∙Alcolin Peel ‘n Seal 10m x 75mm ∙Alcolin Peel ‘n Seal 10m x 100mm ∙Alcolin Peel ‘n Seal 10m x 150mmProduct datai. Physical dataii. Application dataiii. Performance dataThe above information is only offered, as a guide to the use of this product. Furthermore, users should satisfythemselves that it is suitable for their needs. Since we have no control over the conditions under which it is used, wecannot accept responsibility for problems caused by the use and/or application of this product.Head Office: +27(0)21 555 7400Toll free no: 0800 222 400 Array 1 Beverley Close, Montague GardensPO Box 37008, Chempet, 7442。
自熔硝胶胶带产品说明书
* Not including ARLON 10 mil Rectangle which has a shelf life of 12 months.
Product Sell Sheet
Self-Fusing Silicone Tapes
ARLON and Mox Tape Rectangular Tape
Applications:
Mechanical • Wire Harness and Bundling Wrap • Emergency Pipe and Hose Repair • Pipe Identification • Air Duct Sealing • Coolant Line Repairs • Traction and Protection for Rollers
Rectangular tape is of uniform thickness and is ideal for applications where a smooth, even layer of tape is not required.
ARLON and MOX Tape Fiberglass Reinforced Tape These self-fusing silicone tapes incorporate a sinusoidal fiberglass fabric that gives a controlled elongation and increased tear resistance. 15% and 25% controlled elongation fabrics are available.
3M Scotch 盒缝胶带吊带 HR-80 HR-83 说明书
Instructions and Parts ListScotch®Box Sealing Tape DispenserHR 80 (2 inch) HR 83 (3 inch)Model 11000DescriptionThe Tape Dispenser HR 80 / HR 83 provides a quickand easy method for dispensing Scotch® Box SealingTapes directly from the roll. This lightweight, hand-held,portable dispenser is recommended for center seamsealing of RSC boxes.Box Sealing Tape Dispenser HR 80 / HR 83 Specifi cationsTape:For use with most Scotch® Box Sealing Tapes.Tape Widths:HR 80 - 2 inch or 55mm maxHR 83 - 3 inch or 72mm maxTape Roll Diameter:Up to 5-1/8 inch [130mm] maximum on a 3 inch [76.2mm]diameter core.Overall Dimensions:Length: 5 3/4 inches [145mm]Height 10 inches [255mm]Width HR 80 - 2 3/4 inches [ 70mm]HR 83 - 3 3/4 inches [ 95mm]Weight Packaged 1.45 lbs. [0.65 kg]Unpackaged 1.25 lbs. [0.56 kg]Loading InstructionsFigure 1 - Place tape roll fully onto tape drum todispense tape forward from top of roll.Pull tab to remove and discard bladeprotection.Figure 2 - Pivot brake to open position. Threadtape between roller and brake.Figure 3 - Bring tape up and around roller and pullback slightly to one side to cut off excesstape. Adjustable tape roll tension provided.Operating Instructions (Figure 4)A. Place tape and applicator roller on box frontcorner (centered on top seam). Roll dispenserdown to tack tape lead end to side of box.B. P ull dispenser across box top seam applyingpressure to applicator roller in order to obtain atightseal.C. C ontinue tape web 2 1/2 to 3 inches or 65 to 75mmpast end of box.D. B ring dispenser tape wipe-down plate against thecorner of the box. Push down while slightly twistingto cut and wipe tape end to back side of boxes.12Equipment Warranty and Limited Remedy: THE FOLLOWING WARRANTY IS MADE IN LIEU OF ALL OTHER WARRANTIES, EXPRESS OR IMPLIED, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTY OF MERCHANTABILITY, THE IMPLIED WARRANTY OF FITNESS FOR A PARTICULAR PURPOSE AND ANY IMPLIED WARRANTY ARISING OUT OF A COURSE OF DEALING, A CUSTOM OR USAGE OF TRADE:3M warrants that its Scotch ® Box Sealing Equipment will be free from defects for ninety (90) days after delivery. If any part is proved to be defective within the warranty period, then the exclusive remedy and 3M’s and seller’s sole obligation shall be, at 3M’s option, to repair or replace the part, provided the defective part is returned immediately to 3M’s factory or an authorized service station designated by 3M. A part will be presumed to have become defective after the warranty period unless the part is received or 3M is noti fi ed of the problem no later than fi ve (5) calendar days after the warranty period. If 3M is unable to repair or replace the part within a reasonable time, then 3M, at its option, will replace the equipment or refund the purchase price.Limitation of Liability: 3M and seller shall not be liable for direct, indirect, special, incidental or consequential damages based upon breach of warranty, breach of contract, negligence, strict liability or any other legal theory.The foregoing Equipment Warranty and Limited Remedy and Limitation of Liability may be changed only by a written agreement signed by authorized of fi cers of 3M and seller.Model Part NumberDescriptionHR 80 78-8137-3530-1 2" Blade/Wiper Assembly HR 83 78-8137-3531-9 3" Blade/Wiper AssemblyMinimum billing on parts orders is $25.00. Replacement part prices available on request. $10.00 restocking charge per invoice on returned parts.Outside the U.S., contact the local 3M subsidiary for parts ordering information.How To Order Replacement Parts1. Refer to parts list for correct part number.2. Order by description, dispenser name, andpart number.3. Replacement parts and part prices availabledirect from:How To Replace the Wiper and Blade Assembly 1. Remove screws to detach used wiper and bladeassembly.2. Install new wiper and blade assembly withserrated cutting edge pointing away from applicator roller.3. Replace and tighten screws to secure new wiperand blade assembly (Figure 5).3M Tape Dispenser Parts 241 Venture DriveAmery, WI 54001-1325800-344-9883Fax: 715-268-8153Replacement Parts List To reduce the risk associated withsharp blade hazards:Keep hands and cutoff blade. The blade is extremely sharp.Figure 5Replacement IllustrationIndustrial Adhesives and Tape Division 3M Center, Building 220-5E-06St. Paul, MN 55144-10001-800-362-3550/packaging“Scotch” is a trademark of 3M Company "3M" is a trademark of 3M Company,St. Paul, Minnesota 55144-1000Printed in U.S.A.© 3M 2011 44-0009-2199-9 (C042911-NA)。
- 1、下载文档前请自行甄别文档内容的完整性，平台不提供额外的编辑、内容补充、找答案等附加服务。
- 2、"仅部分预览"的文档,不可在线预览部分如存在完整性等问题,可反馈申请退款(可完整预览的文档不适用该条件!)。
- 3、如文档侵犯您的权益，请联系客服反馈,我们会尽快为您处理(人工客服工作时间：9:00-18:30)。
升辉包装实业有限公司产品说明书
1、铝箔胶粘带
铝箔胶粘带是以铝箔为基材, 涂以丙烯酸型(式或橡胶型) 压敏胶, 再复以单面防粘牛皮纸制造而成, 广泛用于冰箱、空调、冷暖气管的包托及电子工业上。
2、牛皮纸胶
粘带是以牛皮纸为基材, 涂以热溶胶型(或橡胶型) 压敏胶制造而成, 主要用于纸箱包装及要求剥开PE层进行加工的场合。
3、双面胶粘带
是在基材的两面涂上压敏胶, 再复上易剥离的离型纸制造而成, 广泛用于两物体的粘接和固定, 使用十分方便.
4、聚酰亚胺
为基材涂布耐高温硅胶而成, 粘性佳,服贴性好,耐高温, 耐溶剂, 不渗锡,不残胶.。
用于电子工业中, 印刷线路板镀金手指,热风锡孔加工及过锡炉中各阶段遮蔽保护。
5、 3M胶带
特别适用于金属加强筋的固定与粘接
6、铝薄胶带
特性: 以纯铝箔为基材, 剥离强度高, 初粘性好, 内聚力强, 耐候性好, 耐高低温性能好。
使用:主要用于电冰箱、冷冻设备及保温工程的外包装
7、美纹胶带
材质: 美纹纸, 橡皮胶。
特征: 粘度适中, 不残胶, 不损毁纸张表面, 易撕, 使用方便, 服贴性强, 耐高温, 耐酸碱等。
用途: 适用常温的喷漆, 涂装, 遮掩及保护, 美工劳作及简易包装; 也能提供高温环境下工艺作业, 具有保护与固定作用; 还可用于汽车, 五金, 电子, 电器等行业的烤漆, 波风焊等
特性: 有极佳的粘性, 耐温性好, 抗拉强度佳, 保持力好无残胶, 能在高温环境下进行多次烘烤
使用: 广泛应用于电子元器件如: 陶瓷电容, 涤纶电容, 金属化容, 热敏电阻等产品制造过程中的编带。
您可根据对温度的要求不同来选择不同型号的胶带。
宽度长度可根据您的不同需要进行选择。
8、 PET双面胶带或微粘胶带
PET聚酯基材, 双面涂布丙烯酸或压克力胶, 防水绝缘等优点。
1.粘着力大, 持粘性和出粘性好, 耐高温、耐溶剂性良好, 耐热性和耐久性亦佳。
适用于电
子铭板及薄膜开关的绝缘和固定。
2.粘接性能良好, 经久不变色, 抗拉强度大, 便于冲切, 适用于个人电脑、移动电话的键盘
固定, 各种电子仪器里薄层及通明物体的粘接和固定。
9、十字纤维玻璃胶带:
广泛地用于变压器和马达、微电机绝缘包扎等。
该材料无毒, 无异味, 使用中对人体安全, 用完后也不会对环境造成污染
10、地板胶带:
粘性佳, 持久性强, 鲜艳醒目。
用于警示标志, 装饰标贴, 地面、墙面标志线等。
11、 OPP印刷胶带:
材质、聚丙烯膜、采用环保压克力胶、产品初粘力, 剥离力、特粘力强、用上等水性压克力胶精制而成、不变色、不变质、耐寒性隹、抗老化、环保符合欧盟国家包装料标准、色彩鲜艳、图案清晰。
可印刷, 具有多种颜色特性 : 粘性佳 , 耐侯性佳 , 可制作红、黄、黑、蓝、绿、米黄等多种颜色。
可用于包扎、封箱、文具办公等。
12、海绵胶带( 泡绵)
该产品由 EVA 泡棉在其双面涂上油胶而成。
特强粘力; 海棉高密度不易裂开; 其主要用于其固定作用, 封闭物件及减震等方面。
13、双面胶带
1 、特性: 以绵纸为基材 , 具有粘力强、易剥离、厚度均匀、使用方便等优点。
2 、用途: 主要用于装饰、装修、邮政、制鞋、服装等行业代替胶粘剂使用, 经济有效地进行各种粘接、裱装、固定等。
3 、分类: 按特性分有水胶( 中粘) 和油胶( 高粘) 。
14、矽硅胶带
(一)产品特性:
1:极高的传热性和缓冲性,不会对PCB,玻璃等带来损害2:对热具有行强稳定性3具有极高的回复力和抗粘性
(二)产品规格1:防静电级(黑色)和普通级(灰色)2:常见厚度为0.2MM,0.25MM,0.3MM,长度为5M,10M等,宽度可定做
15、醋酸布胶带
产品采用进口优质醋酸纤维布为基材, 具有耐高温、耐溶剂, 抗老化佳等特点, 具有性能稳定可靠的特点。
广泛作为电子工业中变压器、马达、线束、线圈电容器及变频电源供应器等缠绕用之绝缘材料。
特性: 绝缘性好, 阻燃, 黏度高
16、免湿水牛皮纸
特性: 以高度牛皮纸为基材, 免水牛皮纸涂热敏胶制造而成, 湿水牛皮纸涂。
2 、用途: 主要用于各种瓦楞纸板箱、塑箱的密封, 建筑业各种板材的粘缝和遮蔽等。
17、 BOPP 封箱胶带( 文具膜)
1 、特性: 以 OPP 基材, 表面涂水性丙烯酸酯类胶粘剂制成。
具有高抗拉伸、耐低温、高粘或低粘和可印刷的优点。
2 、用途: 主要用于装饰、装修、邮政、制鞋、服装等行业代替胶粘剂使用, 经济有效地进行各种。
3 、分类: 按其厚度分为: 38V-53V 。
按其颜色分有透明及客户所要求色泽。
18、绣花胶带
主要用于电脑绣花的多次重复使用
19、 3M直纤维胶带
特色: 进口环保固定胶带, 塑料纤维强化背材, 张力强度极高, 不易断裂。
粘力极强, 包装效果完美且不易松脱。
具有高度的耐磨性能及抗潮湿性能。
透明度高, 胶带绝不脱胶, 而经3M纤维胶带贴过的一般金属或塑料表面上不会遗留胶渍。
美观不生锈,不会污染被捆物, 色彩光亮。
用途广、特性多, 可用最经济的份量, 达到最佳的包装效益。
用途: 家电产品包装: 如洗衣机、雪柜……等
金属及木制家具的包装、垫板/卡板运输、纸箱包装
用法: 零载物品之包装、固定。
典型客户: 宝钢、日宝钢材, TCL冰箱、海尔电器、美的空调、华凌空调、万宝冰箱、格力空调、长江家具等知名企业.
20、布基胶带
种类有: 单面布基胶带、双面布基胶带、纤维布胶带
该产品以棉布涂塑纤维布为基材, 涂于特种橡胶型胶粘剂, 具有初粘性好, 粘合力强, 使用方便, 是家电行业、建筑装璜、车辆厂、造船工业、丝印行业以及产品定位等的最佳产品。
21、美纹胶带
1 、特性: 以高级美纹纸为基材, 具有耐高温、耐溶剂、不残胶等特性。
2 、用途: 主要用于喷漆、烤漆、封箱、鞋业类、包装固定、建筑装潢等行业。
3 、分类: 按温度分: 高温、中温。
按颜色分: 白色和米黄色。
22、高温双面胶
适用于一般日用品的粘接和固定, 广泛应用于金属与塑料间的粘接, 铭牌的固定和海棉的粘贴等。
23、 BOPP 封箱胶带( 文具膜)
特性: 以 OPP 基材, 表面涂水性丙烯酸酯类胶粘剂制成。
具有高抗拉伸、耐低温、高粘或低粘和可印刷的优点。
用途: 主要用于装饰、装修、邮政、制鞋、服装等行业代替胶粘剂使用, 经济有效地进行各种。
分类: 按其厚度分为: 38V-53V 。
按其颜色分有透明及客户所要求色泽。
24、尼龙补强胶带
粘力强劲, 韧力十足, 理想的拉伸率, 特别适用于如手袋的提手、鞋类的鞋帮及受力部位。
25、 PVC高温兰膜
耐高温200度,材质:PVC 粘性:中粘
26、文具胶带
适用于制图纸的固定, 各种纸张、书籍、本的修复及表皮的粘贴保护。