大华防爆高清一体化高速球型摄像机安装指导书V1.0.0-130419
大华红外智能球型摄像机使用说明书(F12)V1.3.0
4 线缆连接 .............................................................................................................................. - 33 4.1 线缆连接 ........................................................................................................................................... - 33 4.2 系统连接 ........................................................................................................................................... - 34 4.2.1 系统图 ...................................................................................................................................... - 34 4.2.2 报警连接图 ............................................................................................................................... - 34 -
1.2 使用环境要求 请避免将设备对准强光（如灯光照明、阳光等）聚焦，否则容易引起过亮或拉光现象（这并非设备故 障） ，也将影响感光器件 CCD（或 CMOS）的寿命。 请在允许的湿度和温度范围内运输、使用和存储设备。不要将设备置于潮湿、多尘、极热、极冷、强 电磁辐射或照明条件不稳定等场所。 请用户使用时不要让水及任何液体流入设备，以免内部元件受损。 为了避免热量积蓄，请不要阻挡设备附近的通风。 运输、存储及安装过程中要防止重压、剧烈振动、浸泡等对产品造成的损坏。 当运送摄像机时，需重新以出厂时的包装进行包装，或用同等品质的材质包装。 产品建议配合防雷器使用，以达到更好的防雷效果。 产品上的接地孔建议接地，进一步提高设备的可靠性。
一体化球型摄象机安装操作指导书
1、 壁挂式
图 1 壁挂式安装示意图
壁挂式球机可用于室内、室外环境的硬质墙壁结构，具体安装步骤见第 6-9
页。
2、 角装式
角装式球机可用于
室内、室外环境的成 90°
夹角的硬质墙壁结构，具
体见安装步骤第 10-11 页。 3、 柱装式
图 2 角装式安装示意图
柱装式球机可用于室内、室外环境的硬质柱状结构，具体见安装步骤第
如图 28 所示，拧松松不脱螺钉，打开翻板。 连接电缆:参见图 9 壁挂支架式球机电缆的连接； 连接下罩:参见图 12 壁挂支架式球机下罩的连接； 安装机芯:参见图 11 壁挂支架式球机机芯的安装；
安装下罩:参见图 13 壁挂支架式球机下罩的安装。
安装壁挂支架:
如图 6 所示，以壁挂支架底面
的安装孔为模板，在墙壁上画出打孔
图 6 打安装孔
位置，并打孔。 如图 7 所示，用内六角螺钉将壁挂支架和壁挂装外罩组件
装配好（注意安装防水密封垫，作好防水操作）。
M5×12 内六角螺钉 壁挂装外罩组件
壁挂支架
图 7 安装外罩组件
如图 8，将支架和外罩组件安装好后，拧开松不脱螺钉，打开翻板，将电线 电缆穿过壁挂支架，并将壁挂支架固定到墙壁上。在安装过程中，注意作好支架 与墙面之间的防水密封事宜。
支架式安装壁挂式安装示意图壁挂式球机可用于室内室外环境的硬质墙壁结构具体安装步骤见第69角装式球机可用于室内室外环境的成90夹角的硬质墙壁结构具体见安装步骤第1011柱装式球机可用于室内室外环境的硬质柱状结构具体见安装步骤第1112柱装式安装示意图图4a无杆吊装安装示意图图4b直杆吊装安装示意图球型摄像机安装单元壁挂支架球机安装安装条件
吊装支架球机安装
大华硬盘录像机快速操作指南
6.2
报警输出端口说明
报警输入示意图
·3 路开关量报警输出（常开触点），外部报警设备需有电源供电； ·为避免过载而损坏主机，连接时请参阅继电器相关参数，继电器参数详见光盘中电子版说明书； ·RS485 的 A、B 线说明：用于云台解码器的 A、B 线的连接。
6
软件界面基本操作
1 开机
插上电源线，按下后面板的电源开关，电源指示灯亮，录像机开机，开机后视频输出默认为多画面输 出模式，若开机启动时间在录像设定时间内，系统将自动启动定时录像功能，相应通道录像指示灯亮，系 统正常工作。
在每个预览画面上有叠加的日期、时间、通道名称，பைடு நூலகம்幕下方有一行表示每个通道的录像及报警状态
图标（各种图标的含义见下表）。
通道画面提示：
监控通道录像时，通道画面上
1
3
显示此标志
通道发生动态检测时，通道上
2
4
画面显示此标志
通道发生视频丢失时，通道画面显示此标志
该通道处于监视锁定状态时通道画面上显示 此标志
以太网口的连接时请注意：当与电脑的网卡接口直接连接时，使用反线；当通过集线器或交换机与电脑连 接时，使用正线。
4
5 安装连接示意图
（以 8 路机器为例）
6 报警输入输出设备的连接
报警输入的输入类型不限，可以是常开型也可以是常闭型。 AB 接线头
5
报警输入输出描述： a) 图上 DOWN 一排所示从左到右 1，2，3，4，5，6，7，8 对应报警输入 ALARM1～ALARM8；报警输 入为接地电平有效； b) 图上 UP 一排 1-NO C，2-NO C，3-NO C，为三组常开联动输出（开关量）； c) A、B为控制 485 设备的A，B线，用于接控制解码器等录像机控制设备。如果云台解码器数量较多， 请在A，B线并入 120Ω的电阻； d) “ ”：地线。
大华硬盘录像机快速操作指南
5 录像时间的设置
硬盘录像机在第一次启动后的默认录像模式是 24 小时连续录像。进入菜单，可进行定时时间内的连 续录像，即对录像在定时的时间段内录像，详细设置在【菜单】>【系统设置】>【录像设置】。
【通 道】选择相应的通道号进行通道设置，统一对所有通道设置可选择【全】； 【星 期】设置普通录像的时间段，在设置的时间范围内才会启动录像；
密码安全性措施：每 30 分钟内试密码错误 3 次报警，5 次帐号锁定。 注：为安全起见，请用户及时更改出厂默认密码。 关于输入法：除硬盘录像机前面板及遥控器可配合输入操作外，可按 文大小写、中文(可扩展)切换，并直接在软面板上用鼠标选取相关值。
按钮进行数字、符号、英
7
4 预览
设备正常登录后，直接进入预览画面。
10
8.3． 抓图优先级
触发抓图优先级>定时抓图。当定时抓图和触发抓图同时开启，如果有相应的报警产生，就进行相应 的触发抓图；如果没有相应的报警产生，就进行定时抓图。
8.4． 图片 ftp
1. 在【网络设置】>【FTP 设置】中，设置 FTP 服务器相关信息；选中 FTP 使能，点击保存。FTP 详 细的操作请参考光盘中的电子说明书。
9
8 抓图设置 8.1． 定时抓图
1. 在【系统设置】>【编码设置】>【抓图设置】中，设置各通道定时抓图的参数，包括【图片大小】、 【图片质量】和【抓图频率】。
2. 在【系统设置】>【普通设置】中，设置【图片上传间隔】。 3. 在【系统设置】>【录像设置】中，选中相应通道的【抓图】使能。 4. 上述操作后定时抓图功能被开启。
以太网口的连接时请注意：当与电脑的网卡接口直接连接时，使用反线；当通过集线器或交换机与电脑连 接时，使用正线。
大华 IR 水银灯网络摄像机快速入门指南 V1.0.0说明书
IR Bullet Network CameraV1.0.0ZHEJIANG DAHUA VISION TECHNOLOGY CO., LTDForewordGeneralThis Quick Start Guide (hereinafter referred to be "the Guide") introduces the functions, installation and operations of the camera.Safety InstructionsSignal WordsMeaning Indicates a medium or low potential hazard which, if not avoided, could result in slight or moderate injury.Indicates property damage, data loss, lower performance, or unpredictableresult.Provides additional information as the emphasis and supplementto the text. Revision HistoryProtect Privacy NoticeAs the device user or data controller, you might collect personal data of others' such as face, fingerprints, car plate number, Email address, phone number, GPS and so on. You need to be in compliance with the local privacy protection laws and regulations to protect the legitimate rights and interests of other people by implementing measures include but not limited to: providing clear and visible identification to inform data subject the existence of surveillance area and providing related contact.About this Guide●The Guide is for reference only. If there is inconsistency between the Guide and the actual product, the actual product shall prevail. ●We are not liable for any loss caused by the operations that do not comply with the Guide. ● The Guide would be updated according to the latest laws and regulations of related regions. For detailed information, see the paper Quick Start Guide, CD-ROM, QR code or our official website. If there is inconsistency between paper User's Guide and the electronic version, the electronic version shall prevail.●All the designs and software are subject to change without prior written notice. The productupdates might cause some differences between the actual product and the Guide. Please contact the customer service for the latest program and supplementary documentation.●There still might be deviation in technical data, functions and operations description, orerrors in print. If there is any doubt or dispute, please refer to our final explanation.●Upgrade the reader software or try other mainstream reader software if the Guide (in PDFformat) cannot be opened.●All trademarks, registered trademarks and the company names in the Guide are theproperties of their respective owners.●Please visit our website, contact the supplier or customer service if there is any problemoccurred when using the device.●If there is any uncertainty or controversy, please refer to our final explanation.Important Safeguards and Warnings Electrical safety●All installation and operation should conform to your local electrical safety codes.●The power source shall conform to the Safety Extra Low Voltage (SELV) standard, andsupply power with rated voltage which conforms to Limited power Source requirementaccording to IEC60950-1. Please note that the power supply requirement is subject to thedevice label.●Make sure the power supply is correct before operating the device.● A readily accessible disconnect device shall be incorporated in the building installationwiring.●Prevent the power cable from being trampled or pressed, especially the plug, power socketand the junction extruded from the device.Environment●Do not aim the device at strong light to focus, such as lamp light and sun light; otherwise itmight cause over brightness or light marks, which are not the device malfunction, andaffect the longevity of Complementary Metal-Oxide Semiconductor (CMOS).●Do not place the device in a damp or dusty environment, extremely hot or coldtemperatures, or the locations with strong electromagnetic radiation or unstable lighting.●Keep the device away from any liquid to avoid damage to the internal components.●Keep the indoor device away from rain or damp to avoid fire or lightning.●Keep sound ventilation to avoid heat accumulation.●Transport, use and store the device within the range of allowed humidity and temperature.●Heavy stress, violent vibration or water splash are not allowed during transportation,storage and installation.●Pack the device with standard factory packaging or the equivalent material whentransporting the device.●Install the device in the location where only the professional staff with relevant knowledgeof safety guards and warnings can access. The accidental injury might happen to thenon-professionals who enter the installation area when the device is operating normally. Operation and Daily Maintenance●Do not touch the heat dissipation component of the device to avoid scald.●Carefully follow the instructions in the Guide when performing any disassembly operationabout the device; otherwise, it might cause water leakage or poor image quality due tounprofessional disassemble. Please contact after-sale service for desiccant replacement ifthere is condensed fog found on the lens after unpacking or when the desiccant turnsgreen. (Not all models are included with the desiccant).●It is recommended to use the device together with lightning arrester to improve lightningprotection effect.●It is recommended connect the grounding hole to the ground to enhance the reliability ofthe device.●Do not touch the image sensor directly (CMOS). Dust and dirt could be removed with airblower, or you can wipe the lens gently with soft cloth that moistened with alcohol.●Device body can be cleaned with soft dry cloth, which can also be used to removestubborn stains when moistened with mild detergent. To avoid possible damage on device body coating which could cause performance decrease, do not use volatile solvent such as alcohol, benzene, diluent and so on to clean the device body, nor can strong, abrasive detergent be used.●Dome cover is an optical component, do not touch or wipe the cover with your handsdirectly during installation or operation. For removing dust, grease or fingerprints, wipe gently with moisten oil-free cotton with diethyl or moisten soft cloth. You can also air blower to remove dust.●Please strengthen the protection of network, device data and personal information byadopting measures which include but not limited to using strong password, modifying password regularly, upgrading firmware to the latest version, and isolating computer network. For some device with old firmware versions, the ONVIF password will not be modified automatically along with the modification of the system password, and you need to upgrade the firmware or manually update the ONVIF password.●Use standard components or accessories provided by manufacturer and make sure thedevice is installed and maintained by professional engineers.●The surface of the image sensor should not be exposed to laser beam radiation in anenvironment where a laser beam device is used.●Do not provide two or more power supply sources for the device unless otherwise specified.A failure to follow this instruction might cause damage to the device.Regulatory Information FCC InformationChanges or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment.FCC conditions:This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:●This device may not cause harmful interference.●This device must accept any interference received, including interference that may causeundesired operation.FCC compliance:This equipment has been tested and found to comply with the limits for a digital device, pursuant to part 15 of the FCC Rules. This equipment generate, uses and can radiate radio frequency energy and, if not installed and used in accordance with the guide, may cause harmful interference to radio communication.●For class A device, these limits are designed to provide reasonable protection againstharmful interference in a commercial environment. Operation of this equipment in aresidential area is likely to cause harmful interference in which case the user will berequired to correct the interference at his own expense.●For class B device, these limits are designed to provide reasonable protection againstharmful interference in a residential installation. However, there is no guarantee thatinterference will not occur in a particular installation. If this equipment does cause harmfulinterference to radio or television reception, which can be determined by turning theequipment off and on, the user is encouraged to try to correct the interference by one ormore of the following measures:●Reorient or relocate the receiving antenna.●Increase the separation between the equipment and receiver.●Connect the equipment into an outlet on a circuit different from that to which thereceiver is connected.●Consult the dealer or an experienced radio/TV technician for help.Table of ContentsForeword (I)Important Safeguards and Warnings (I)Regulatory Information (IV)1 Introduction (1)1.1 Cable (1)1.2 Connecting Alarm Input/output (2)2 Network Configuration (4)2.1 Initializing Device (4)2.2 Modifying Device IP Address (5)2.3 Logging in Web Interface (6)3 Installation (8)3.1 Packing List (8)3.2 Dimension (8)3.3 Installing Device (9)3.3.1 Installation method (9)3.3.2 Installing SD Card (Optional) (9)3.3.3 Attaching Device (10)3.3.4 Installing Waterproof Connector (12)3.3.5 Adjusting Angle (12)3.3.6 Adjusting Focal Length (13)1 Introduction1.1 Cable●Cable type might vary with different devices, and the actual product shall prevail.●Please waterproof all the cable joints with insulating tape and waterproof tape to avoidshort circuit and water damage. For the detailed operation, see the FAQ manual.Cable listFigure 1-1For more information about cable ports, see Table 1-1.information, see Table 1-2.Connects to network with network cable.●Provides power to the device with PoE.●PoE is available on select model.Connects to sound-pick-up device to receive audio signal.For more information about I/O port, see Table 1-2.1.2 Connecting Alarm Input/outputAlarm input/output is available on select models.Step 1Connect alarm input device to the alarm input end of the I/O port, see Figure 1-2.Device collects different states of alarm input port when the input signal is idling andbeing grounded.●Device collects logic "1" when input signal is connecting to +3V to+5V or idling.●Device collects logic "0" when input signal being grounded.Figure 1-2Alarm inputStep 2Connect alarm output device to the alarm output end of the I/O port. The alarm outputis open-drain output, which works in the following modes.●Mode A: Level application. Alarm outputs high and low level, and the alarm outletis OD, which requires external pull-up resistance (10K Ohm typical) to work. Themaximum external pull-up level is 12V, maximum port current is 300mA and thedefault output signal is high level (external pull-up voltage). The default outputsignal switches to low level when there is alarm output (As long as the operatingcurrent below 300mA, the output low level voltage is lower than 0.8V).●Mode B: Switch application. Alarm output is used to drive external circuit, themaximum voltage is 12V and the maximum current is 300mA. If the voltage ishigher than 12V, please use an additional electric relay.Figure 1-3Mode AMode BFigure 1-4Log in web interface, and configure alarm input and alarm output in alarm setting. Step 3●The alarm input in the web interface is corresponding to the alarm input end of theI/O port. There will be high level and low level alarm signal generated by the alarminput device when alarm occurs, set the input mode to "NO" (default) if the alarminput signal is logic "0" and to "NC" if the alarm input signal is logic "1".●The alarm output in the web interface is corresponding to the alarm output end ofthe device, which is also alarm output end of the I/O port.2 Network ConfigurationDevice initialization and IP setting can be finished with the "ConfigTool" or in web interface. For more information, see the WEB operation manual.●Device initialization is available on select models, and it is required at first use and afterdevice is being reset.●Device initialization is available only when the IP addresses of the device (192.168.1.108by default) and the PC stays in the same network segment.●Planning useable network segment properly to connect the device to the network.●The following figures and interfaces are for reference only, and the actual product shallprevail.2.1 Initializing DeviceDouble-click "ConfigT ool.exe" to open the tool.Step 1Click.Step 2The Modify IP interface is displayed. See Figure 2-1.Modify IP interfaceFigure 2-1Click Search setting.Step 3The Setting interface is displayed.Enter the start IP and end IP of the network segment in which you want to search Step 4devices, and then click OK.All the devices found in the network segment are listed.Step 5Select one or several devices which Status are Uninitialized, and then click Initialize.The Device initialization interface is displayed.Select the devices that need initialization, and then click initialize.Step 6The password setting interface is displayed. See Figure 2-2.Figure 2-2Password setting interfaceStep 7Set and confirm the password of the devices, and then enter a valid email address.Click Next.The final setting interface is displayed.Password can be modified or reset in System Settings.Step 8Select the options according to your needs and then click OK.The Initialization interface is displayed after initializing is completed. Click the successicon () or the failure icon () for the details.Step 9Click Finish.The device status in the Modify IP interface (Figure 2-1) turns to Initialized.2.2 Modifying Device IP Address●You can modify IP address of one or multiple devices in one time. This section is based onmodifying IP addresses in batch.●Modifying IP addresses in batch is available only when the corresponding devices have thesame login password.Step 1Double-click "ConfigT ool.exe" to open the tool.Click.Step 2The Modify IP interface is displayed. See Figure 2-1.Select the devices which IP addresses need to be modified, and then click Modify IP.Step 3The Modify IP Address interface is displayed. See Figure 2-3.Figure 2-3Modify IP Address interfaceStep 4Select Static mode and enter start IP, subnet mask and gateway.●IP addresses of multiple devices will be set to the same if you select Same IP.●If DHCP server is available in the network, devices will automatically obtain IPaddresses from DHCP server when you select DHCP.Step 5Click OK.2.3 Logging in Web InterfaceStep 1Open IE browser, enter the IP address of the device in the address bar and pressEnter.If the setup wizard is displayed, follow the instructions to finish the settings.Step 2Enter user name and password in the log in box, and then click Login.Step 3For first time login, click Click Here to Download Plugin and install the plugin asinstructed.The main interface is displayed when the installation is finished. See Figure 2-4.Main interface Figure 2-43 Installation3.1 Packing List●The tool required for the installation such as electric drill is not provided in the packing.●The operation manual and related tool are contained in the disk or the QR code, and theactual packing shall prevail.3.2 DimensionFollowing figures are for reference only, the actual product shall prevail.3.3 Installing Device 3.3.1 Installation methodWall-mounted Pole-mountedAngle-mounted Ceiling-mounted3.3.2 Installing SD Card (Optional)●SD card slot is available on select models.●Please disconnect the power from the device before installing the SD card.●Press the reset button for 10 seconds to reset the device.3.3.3 Attaching DeviceMake sure the mounting surface is strong enough to hold at least three times of the device weight.Cable going through the mounting surfaceCable going through the side cable tray3.3.4 Installing Waterproof ConnectorThis part is only needed when there is waterproof connector come with the device and the device is used outdoor.3.3.5 Adjusting Angle3.3.6 Adjusting Focal LengthZhejiang Dahua Vision Technology Co., LtdAddress：No.1199 Bin’an Road, Binjiang District, Hangzhou, PRC. Postcode: 310053Tel: +86-571-87688883Fax: +86-571-87688815Email:**********************Website: 。
【VIP专享】大华130万高清一体化摄像机机芯使用说明书V1.0_20110318
2. 警告
2.1 本产品的安装及维修应由专业服务人员进行，请勿自行进行拆卸及维修等操作。 2.2 请勿使本产品受潮或雨淋，以减少火灾或电击危险。 2.3 CCD 光学元件可能会受到激光束的损坏，故在使用激光束设备时，请避免使 CCD 表面受到激光束的辐
射。
3. 声明
3.1 产品请以实物为准，说明书仅供参考。 3.2 产品实时更新，如有升级恕不另行通知。 3.3 最新程序及补充说明文档敬请与公司客服部联系。 3.4 产品说明中有疑问或争议的，请以本公司最终解释为准。 3.5 如在使用设备时发生任何问题，请与供应商或公司客服部联系。 3.6 我们已尽量保证说明书中内容的完整与准确，但部分数据仍可能与实际值存在偏差，如有任何疑问或
3 数字视频输出..........................................................................................................................- 6 -
3.1 数字输出电压特性................................................................................................................................ - 6 3.2 数字输出同步时序................................................................................................................................ - 7 -
障），也将影响 CCD 传感器寿命。 b) 请在允许的湿度和温度范围内使用该设备，避免在高温高湿的极端环境下使用。不要将设备置于潮湿、
大华 防爆一体化云台摄像仪 使用说明书
防爆一体化云台摄像仪使用说明书V1.0.2浙江大华技术股份有限公司防爆标志：Ex d IIC T6 Gb/Ex tD A21 IP68 T80℃前言概述本文档详细描述了防爆一体化云台摄像仪的产品概述、安装、连接、使用等内容。
符号约定在本文档中可能出现下列标识，代表的含义如下。
标识说明表示有中度或低度潜在危险，如果不能避免，可能导致人员轻微或中等伤害。
表示有潜在风险，如果忽视这些文本，可能导致设备损坏、数据丢失、设备性能降低或不可预知的结果。
表示是正文的附加信息，是对正文的强调和补充。
修订记录版本号修订内容发布日期V1.0.2 删除敏感词汇。
2020.11V1.0.1 更新模板。
更新公司。
2020.09V1.0.0 首次发布。
-装箱清单开箱之后请仔细核对包装箱内设备及配件，如有异样及缺失，请及时与当地供应商或公司客服部（400-672-8166）联系，产品实时更新，如有更改，恕不另行通知。
如有任何疑问或争议，请以公司最终解释为准。
序号名称数量备注1 防爆一体化云台摄像仪 1 -2 遮阳罩 1 -3 使用说明书 1 -4 产品合格证 1 -5 M10×45内六角圆柱头螺钉、平垫、弹垫、螺母5套用于安装一体化摄像仪6 M3、M10内六角扳手各1 安装产品、调试雨刷用7 防爆挠性管 1 1米使用安全须知感谢您选用本公司的防爆产品！安装、使用前请仔细阅读本手册，遵守警告事项，并妥善保存好本手册。
质量保证对于本公司生产的防爆一体化云台摄像仪在产品保修期内，本公司提供免费维修服务，但如有以下情形者，将酌情收取材料成本工时费用：●不按照使用说明书中的规定进行操作导致损坏。
●擅自拆机导致损坏。
●雷击及不可抗拒的自然灾害。
若公司与用户之间另有书面服务承诺或规定，将严格按照承诺或规定的要求进行处理。
安全保证该设备的运行符合以下两个条件：●设备的运行不会产生有害的干扰。
●设备的运行在一定程度上不受外部干扰，甚至是不良干扰的影响。
大华高清红外子弹网络摄像机快速入门指南
Dahua HD IR Bullet Network Camera Quick Start GuideDahua HD IR Bullet Network CameraQuick Start GuideVersion 1.0.0ZHEJIANG DAHUA VISION TECHNOLOGY CO., LTD.WelcomeThank you for purchasing our network cameras.This user’s manual is designed to be a reference tool for using your product.Please read the following safeguards and warnings carefully before you use this series product. Please keep this user’s manual well for future reference.Important Safeguards and WarningsElectrical safety●All installation and operation should conform to your local electrical safety codes.●The power source shall conform to the requirement of the Safety Extra Low Voltage (SELV)standard, and supply power with rated voltage which conforms to Limited power Sourcerequirement according IEC60950-1. Please note that the power supply requirement is subject to the device label.●Make sure the power supply is correct before operating the device.● A readily accessible disconnect device shall be incorporated in the building installation wiring●Prevent the power cable from being trampled or pressed, especially the plug, power socket and thejunction extruded from the device.●We assume no liability or responsibility for all the fires or electrical shock caused by improperhandling or installation.Environment●Do not aim the device at strong light to focus, such as lamp light and sun light, otherwise it mightcause over brightness or light marks, which are not the device malfunction, and affect the longevity of Charge Coupled Device (CCD) or Complementary Metal-Oxide Semiconductor (CMOS).●Do not place the device in a damp or dusty environment, extremely hot or cold temperatures, or thelocations with strong electromagnetic radiation or unstable lighting.●Keep the camera away from water or other liquid to avoid damages to the internal components.●Keep the indoor device away from rain or damp to avoid fire or lightning.●Keep sound ventilation to avoid heat accumulation.●Transport, use and store the device within the range of allowed humidity and temperature.●Heavy stress, violent vibration or water splash are not allowed during transportation, storage andinstallation.●Pack the device with standard factory packaging or the equivalent material when transporting thedevice.●The device needs to be installed in the location where professional staff can cover (professionalsneed to know the attentions of using the device), non-professionals are not allowed to enter device installation area when the device is operating normally, which may cause accidental damage.Operation and Daily Maintenance●Do not directly touch the heat dissipation component of the device to avoid scald.●Do not dismantle the device because there is no component that can be fixed by users themselves.Otherwise, it might cause water leakage or bad image due to unprofessional dismantling.●Please contact after-sale service to replace desiccant when it becomes green. (The desiccant isnot provided by default)●It is recommended to use the device together with lightning arrester to improve lightning protectioneffect.●It is recommended to get the grounding holes to be grounded to enhance the reliability of thedevice.●Do not directly touch the optic component CCD or CMOS. You can use the air blower to blow awaythe dust or dirt on the lens surface. Please use a dry cloth wetted by alcohol to wipe away the dust gently if necessary.●Use the dry soft cloth to clean the device. If the dust is difficult to be removed, please wipe it awaywith a clean cloth wetted slightly by the mild detergent, and then use the dry cloth to clean the device. Do not use volatile solvents like alcohol, benzene, thinner, or strong detergent withabrasiveness, otherwise it will damage the surface coating or reduce the working performance of the device.●When installing or using the device, do not directly touch or wipe the surface of the dome coverbecause it is an optical device. If stained with dirt, use oil-free soft brush or air blower to gently wipe it away. If stained with grease or fingerprint, use soft cloth to gently wipe the water drop or oil and wait till it is dry, and then use oil-free cotton cloth or lens cleaning paper soaked with alcohol or detergent to wipe from the lens center outward till it is clean.●We are not liable for any problems caused by unauthorized modification or attempted repair.●The dome cover is a kind of optical component, please do not touch or wipe the cover surfaceduring installation and application, it may stain dust, grease or fingerprint, you can use absorbent cotton to dip some diethyl ether or use soft cloth to dip some water and then wipe gently. You can also use air gun to remove the dust if the cover is stained with dust.Warnings●Please strengthen the protection of network, device data and personal information, adoptnecessary measures of guarantee device network security, including but not limited to using strong password, modifying password regularly, upgrading firmware to the latest version, isolatingcomputer network and so on. For the IP camera firmware of some old version, the ONVIFpassword won’t b e modified automatically after the main password of the system is modified. You need to upgrade the camera firmware or upgrade the ONVIF password manually.●Please modify the default password after login to avoid being stolen.●Use the standard components provided by manufacturer and make sure the device is installed andfixed by professional engineers.●The surface of the image sensor should not be exposed to laser beam radiation in an environmentwhere a laser beam device is used.●Do not provide two or more power supply sources for the device; otherwise it might damage thedevice.Disclaimer●This manual is for reference only. Please refer to the actual product for more details.●Minor differences might be found in user interface, and there might be deviation between the actualvalue of some data and the value provided in the manual due to the reasons such as the realenvironment is not stable. Please refer to the final explanation of the company if there is any doubt or dispute.●All the designs and software are subject to change without prior written notice. The manual will beregularly updated according to the product upgrade without prior announcement.●Please contact the supplier or customer service if there is any problem occurred when using thedevice.●Please contact the customer service for the latest procedure and supplementary documentation.●Please visit our website or contact your local service engineer for more information.●The company is not liable for any loss caused by the operation that does not comply with themanual.●If there is any uncertainty or controversy, please refer to our final explanation.Regulatory InformationFCC Information1.1 FCC conditions：This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: ●This device may not cause harmful interference●This device must accept any interference received, including interference that may causeundesired operation.1.2 FCC compliance：This equipment has been tested and found to comply with the limits for a digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference. This equipment generate, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communication. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:●Reorient or relocate the receiving antenna.●Increase the separation between the equipment and receiver.●Connect the equipment into an outlet on a circuit different from that to which the receiver isconnected.●Consult the dealer or an experienced radio/TV technician for help.Note●Please refer to the disk for more details, check and download the corresponding user’s manual andtool.●Before installation, please open the package and check all the components are included.●Contact your local retailer as soon as possible if something is broken in your package.Table of Contents1 Device Framework (6)1.1 Device External Cable (6)1.2 Dimension (7)2 Device Installation (8)2.1 Install SD Card (8)2.2 Fix Device (9)2.3 Connect Device Cable (9)2.4 Adjust Device Angle (12)3 Network Configuration (13)3.1 Device Initialization (13)3.2 Modify IP Address (14)3.3 Login WEB Interface (15)1 Device Framework1.1 Device External CableNote●The following structure figure is for reference only. It is only used to know thefunctions of cable ports.●There might be some minor differences between different devices, so please referto the actual products you purchased.Figure 1-1Please refer to Table 1-1 and Table 1-2 for the functions of external cable and I/O portTable 1-11.2 DimensionNoteThe following figure is for reference only, which is only used to know the devicedimension.Refer to 错误!未找到引用源。
- 1、下载文档前请自行甄别文档内容的完整性，平台不提供额外的编辑、内容补充、找答案等附加服务。
- 2、"仅部分预览"的文档,不可在线预览部分如存在完整性等问题,可反馈申请退款(可完整预览的文档不适用该条件!)。
- 3、如文档侵犯您的权益，请联系客服反馈,我们会尽快为您处理(人工客服工作时间：9:00-18:30)。
1.2 电气指标
电气指标如表 1-1 所示。
参数 输入电压 工作电流 功耗 预置位数量 预置位精度 电气连接
表 1-1 电气指标参照表 指标
220VAC（±15%） ≤250mA 15W /30W（室外加热器开启） 256 ±0.1°
防爆高清球机严格按照 GB3836.1-2010《爆炸性环境 第 1 部分：设备 通用要求》、GB3836.2-2010《爆 炸性环境 第 2 部分：由隔爆外壳“d”保护的设备》及 GB12476.1-2000《可燃性粉尘环境用电气设备第 1 部分：用外壳和限制表面温度保护的电气设备第 1 节：电气设备的技术要求》等标准设计制造，具有体积 小、重量轻、安装方便等特点，可广泛用于石油、化工、码头、港口、矿山、航天、航空、军工、粮食加 工等场所。
1.1 产品特点 ............................................................................................................................................- 1 1.2 电气指标 ............................................................................................................................................- 1 1.3 机械指标 ............................................................................................................................................- 1 1.4 环境条件 ............................................................................................................................................- 2 1.5 产品尺寸 ............................................................................................................................................- 2 1.6 安装孔位尺寸 ....................................................................................................................................- 2 -
符号约定
在本文中可能出现下列标志，它们所代表的含义如下：
符号
说明
பைடு நூலகம்
表示有高度潜在危险，如果不能避免，会导致人员伤亡或严重伤害。
表示有中度或低度潜在危险，如果不能避免，可能导致人员轻微或 中等伤害。
表示有潜在风险，如果忽视这些文本，可能导致设备损坏、数据丢 失、设备性能降低或不可预知的结果。
防静电标识，用于表示静电敏感的设备。
2 防爆高清球机安装.................................................................................................................. - 4 -
2.1 安装注意事项 ....................................................................................................................................- 4 2.2 初始设置 ............................................................................................................................................- 4 2.3 安装方式 ............................................................................................................................................- 5 -
电击防护标识，用于表示高压危险。
激光辐射标识，用于表示强激光辐射。
表示能帮助您解决某个问题或节省您的时间。 表示是正文的附加信息，是对正文的强调和补充。
浙江大华系统工程有限公司
i
防爆高清一体化高速球型摄像机
重要安全须知
重要安全须知
以下是关于产品的正确使用方法以及预防危险、防止财产受到损失等内容，使用设备前请仔细阅读本 说明书并在使用时严格遵守，阅读后请妥善保存说明书。
2.3.1 壁挂式........................................................................................................................................- 5 2.3.2 支架安装定位孔.........................................................................................................................- 6 2.4 整机安装 ............................................................................................................................................- 6 2.5 线缆的处理 ........................................................................................................................................- 8 2.5.1 使用防爆挠性管.........................................................................................................................- 8 3.1 系统连接 ............................................................................................................................................- 9 3.1.1 电缆功能定义 ............................................................................................................................- 9 3.1.2 电源和视频连接.......................................................................................................................- 10 附录 1：放雷击、浪涌 ...............................................................................................................................................- 11 附录 2：RS485 总线常识 .......................................................................................................................................... - 12 -
防爆标志: ExdⅡB+H2 T6 Gb/DIP A20 TA, T6 防爆合格证: CNEx13.0617X 生产许可证编号: XK06-014-01242
防爆高清一体化高速球型摄像机
安装指导书
DH-TD67(Ex)
V1.0.0
浙江大华系统工程有限公司
防爆高清一体化高速球型摄像机
前言
前言
概述
本文档详细描述了防爆高清一体化高速球型摄像机的产品概述、安装、连接、使用等内容。
与说明书中提供的值存在偏差，如有任何疑问或争议，请以公司最终解释为准。 如不按照说明书中的指导进行操作，因此而造成的任何损失由使用方自己承担。
浙江大华系统工程有限公司
ii
防爆高清一体化高速球型摄像机
目录
目录
前言 ....................................................................................................................................................... i 重要安全须知 ...................................................................................................................................... ii 1 产品概述.................................................................................................................................. - 1 -