管件中英文对照
管件中英文对照表
碳钢弯头 Carbon Steel Elbow不锈钢弯头 Stainless Steel Elbow高压弯头 High-Pressure Elbow同心异径管 Concentric Reducers偏心异径管 Eccentric Reducers高压异径管 High-pressure Reducers不锈钢等径三通 Stainless Straight Tee碳钢等径三通 Carbon Straight Tee不锈钢等径四通 Stainless Straight Cross高压三通 High-pressure Tee锻制三通 Forged Tee异径接头 Template 管帽 Caps 法兰flange长径和短径弯头 long and short radius elbows同心和偏心异径接头 concentric and eccentric reducers等径和异径三通 straight and reducing outlet tees大小头 CONCENTRIC REDUCER相等的三通Tee Equal等径三通Straight Tee 异径三通Reducing Tee等径四通Straight Cross90°短半径弯头90°SS Elbow(SR)90°长半径弯头90°SS Elbow (LR)高压厚壁弯头Thickness Elbow U型管ReturnBend盲法兰Blank Flange 弯管Bends翻边stub ends 异径接头reducers 公称通径 nominal diameter外径(mm) outside diameter 中心距至端面的距离center to end理论重量(kg/pcs) approx weight类种description 标准 Standard类型Design 材质Material 双丝头 Nipple短节 SWAGE NIPPLE内外螺纹活接头 Union 螺桩 stud单承口管箍 Half-Coupling 双承口管箍Coupling盲板 Blind Flange 带双圈的盲板 spectacle blind偏心的Ecentric 等径直通equal coupling 异径直通reducing coupling 内牙直通 female coupling外牙直通 straight tube with outside 90等径弯头 90 equal elbow45等径弯头 45 equal elbow 外牙弯头 maleelbow内牙弯头 female elbow 等径三通 equal tee 异径三通 reducing tee 内牙三通femaletee外牙三通 male tee 管帽cap拆除:dismantle 结头（管线的）：tie-in插盲板：slip spade 盲板：blank接头：fitting 加热器：heater金属缠绕垫片（带外环）:SW with outside ring 热轧on site: 管汇manifold∙ 1. 焊接支管台Welding-on collar|平焊环...weldolet|焊接支管台...weldolet|焊接支管台2. 焊接管台Welding repair procedure 补焊工艺...weldolet 焊接管台...Wind vane 风向标3. 对焊管座weldment 焊件...weldolet 对焊管座...well killingpump 压井泵4. 螺纹支管台；对焊管座welding plate flange焊接板式法兰...weldolet螺纹支管台；对焊管座...WN（简）带颈对焊法兰∙ 1. 螺纹管座threaded (THD) 螺纹的...thredolet螺纹管座...thrust fitting推力接头2. 螺纹支管台sockolet 承插焊支管台...thredolet 螺纹支管台...TOP螺纹接头Nier mass spectrometer 尼尔质谱仪...nipple 螺纹接头...Noise equivalent temperature difference （NETD）噪声当量温度差（NETD）3. 短节双丝头 nipple...短节 SWAGE nipple...内外螺纹活接头Union4. 螺纹接套；喷嘴nipper 钳子；拔钉钳...nipple 螺纹接套；喷嘴...noise abatement measure 减低噪音措施1. 弯头支管台elbolet|弯头支管台...elbolet|弯头支管台...elbow|弯头2. 螺纹支管台；弯头管座elastometric lining橡胶内衬...elbolet螺纹支管台；弯头管座3. 斜接支管台Sockolet弯头支管台...elbolet斜接支管台trolet镶入式支管嘴Seamless---无缝的equal-----相等的，同样的Reducers----异径的，不同的blind flange--法兰堵板/盲板法兰盲法兰法兰-FLANGEblind--法兰盖,盲目的HEX==hexagon(六角形;六边形)Head--上端;前端头PLUG—管赌。
管件中英文对照表
1.2 管件 Fitti ng 弯头elbow异径弯头 reducing elbow带支座三通 base tee异径三通（一个直通口及分支口为异径）reduc ing tee (reduc ing on one run and outlet)异径三通（两个直通口为异径，双头式）head ）45 ° 斜三通 45 ° lateralreduc ing tee (reduc ing on both runs, bull45 ° 斜三通(支管为异径) 45 ° lateral (reduci ng on bran ch) 45 ° 斜三通(一个直通口为异径 )45 ° lateral (reducing on one run)45 ° 斜三通(一个直通口及支管为异径)45 ° lateral (reducing on one run and branch) 四通cross（一个直通口及两个分支口为异径） both outlet ） 异径管reducerreduc ing cross (reduc ing on one run and螺纹支管台 threadolet等径四通 straight cross 异径四通 reduc ing cross 异径四通（一个分支口为异径） reduc ing cross (reduc ing on one outlet) 异径四通 outlet ） 异径四通 （一个直通口及分支口为异径）reduc ing cross (reduc ing on one run and （两个分支口为异径） reduc ing cross (reduc ing on both outlet) 同心异径管 concen tric reducer 偏心异径管 ecce ntric reducer 锻制异径管 reduc ing swage焊接支管台 weldolet带支座弯头 base elbow k 半径弯头 long radius elbow短半径弯头 short radius elbow长半径180短半径180 ° 弯头 long radius return ° 弯头 short radius return带侧向口的弯头（右向或左向）side outlet elbow (right hand or left hand) 双支管弯头（形）double branch elbow 三通tee异径三通 reducing tee 等径三通straight tee带侧向口的三通（右向或左向）side outlet tee (right hand or 1eft hand) 异径三通（分支口为异径） reduc ing tee (reduc ing on outlet) 异径三通（一个直通口为异径）reduc ing tee (reduc ing on one run)Y 型三通（俗称裤衩）true “ Y”异径四通AWWA *America n Water Works Associati on 美国水工协会承插支管台 sockolet弯头支管台elbolet 斜接支管台latrolet 镶入式支管嘴swee polet短管支管台nip olet支管台，插入式支管台boss 螺纹支管台承插焊支管台Sockolet支管台，插入式支管台 boss管接头 coupling, full coupling半管接头 half coupling异径管接头 reduc ing cou pli ng活接头union管帽cap (C)堵头plug短节nipple异径短节 reducing nipple; swage nipple 管道英文缩写An chor 固定ABS * Absolute 绝对的AISI *America n Iron and Steel In stitute美国钢铁学会 ANSI * America n Nati onal Stan dards In stitute 美国国家标准学会 API *America n P etroleum In stitute美国石油学会 APPROX ASB *App roximateAsbestos 石棉大约，近似的 ASME ASSY * *America n Society Of Mecha ni cal Engin eers Assembly 装配，组装美国机械工程师协会 ASTM * America n Society Of Test ing Material 美国材料实验协会 ATM * Atmos phere 大气压 AWG *America n Wire Gage 美国线规 AWS * American Wel**** Society 美国焊接协会 Threadolet 弯头支管台elbolet 焊接支管台weldolet ； on weld 短管支管台nip olet 承插支管台sockolet 烧焊支管台weldolet 斜接支管台latrolet内外螺纹缩接（俗称补芯）bushi ng。
管件中英文对照表
管件中英文对照表1、法兰Flange(FLG）整体管法兰integral pipe flange钢管法兰steel pipe flange螺纹法兰threaded flange滑套法兰（包括平焊法兰）slip-on flange(SO);slip-on welding flange 承插焊法兰socket welding flange松套法兰lap joint flange(LJF)对焊法兰welding neckflange(WNF)法兰盖blind flange,blind孔板法兰orifice flange异径法兰reducing flange盘座式法兰pad type flange松套带颈法兰loose hubbed flange焊接板式法兰welding plate flange对焊环welding neck collar（与stub end相似）平焊环welding-on collar突缘短节stub end,lap翻边端lapped pipe end松套板式法兰loose plate flange压力级pressure rating,pressure rating class压力—温度等级pressure-temperature rating法兰密封面，法兰面flange facing突面raised face(RF)凸面male face(MF)凹面female face(FMF)榫面tongue face槽面groove face环连接面ring joint face全平面；满平面flat face;full face(FF)光滑突面smooth raised face(SRF)法兰面加工facing finish粗糙度roughness光滑的smooth齿形serrated均方根root mean square(RMS)算术平均粗糙高度arithmetical average roughness height(AARH)配对法兰companion-flange螺栓圆bolt circle(B.C.)2、管件Fitting弯头elbow异径弯头reducing elbow带支座弯头base elbow长半径弯头long radius elbow短半径弯头short radius elbow长半径180°弯头long radius return短半径180°弯头short radius return带侧向口的弯头（右向或左向）side outlet elbow(right hand or left hand)双支管弯头（形）double branch elbow三通tee异径三通reducing tee等径三通straight tee带侧向口的三通（右向或左向）side outlet tee(right hand or1eft hand)异径三通（分支口为异径）reducing tee(reducing on outlet)异径三通（一个直通口为异径）reducing tee(reducing on one run)带支座三通base tee异径三通（一个直通口及分支口为异径）reducing tee(reducing on one run and outlet)异径三通（两个直通口为异径，双头式）reducing tee(reducing on both runs, bull head)45°斜三通45°lateral45°斜三通（支管为异径）45°lateral(reducing on branch)45°斜三通(一个直通口为异径)45°lateral(reducing on one run)45°斜三通(一个直通口及支管为异径)45°lateral(reducing on one run and branch)Y型三通（俗称裤衩）true“Y”四通cross等径四通straight cross异径四通reducing cross异径四通（一个分支口为异径）reducing cross(reducing on one outlet)异径四通（一个直通口及分支口为异径）reducing cross(reducing on one run and outlet)异径四通（两个分支口为异径）reducing cross(reducing on both outlet)异径四通（一个直通口及两个分支口为异径）reducing cross(reducing on one run and both outlet)异径管reducer同心异径管concentric reducer偏心异径管eccentric reducer锻制异径管reducing swage螺纹支管台threadolet焊接支管台weldolet承插支管台sockolet弯头支管台elbolet斜接支管台latrolet镶入式支管嘴sweepolet短管支管台nipolet支管台，插入式支管台boss管接头coupling,full coupling半管接头half coupling异径管接头reducing coupling活接头union内外螺纹缩接（俗称补芯）bushing管帽cap(C)堵头plug短节nipple异径短节reducing nipple;swage nipple3、弯管Bend预制弯管fabricated pipe bend跨越弯管（^形）cross-over bend偏置弯管（~形）offset bend90°弯管quarter bend环形弯管cirele bend单侧偏置90°弯管（?形）single offset quarter bendS形弯管“S”bend单侧偏置U形膨胀弯管（|?形）single offset“U”bendU形弯管“U”bend双偏置U膨胀弯管double offset expansion“U”bend斜接弯管mitre bend三节斜接弯管3-piece mitre bend折皱弯管corrugated bend圆度roundness4、垫片Gasket(GSKT)垫片的型式type of gasket平垫片flat gasket环形平垫片flat ring gasket平金属垫片flat metal gasket夹棉织物的橡胶elastomer with cotton fabric insertion夹石棉织物的橡胶elastomer with asbestos fabric insertion夹石棉织物及金属丝加强的橡胶elastomer with asbestos fabric insertion and with wire reinforcement无石墨压缩白石棉垫片non graphited compressed white asbestos gasket 天然白橡胶垫片natural white rubber gasket压缩石棉垫片compressed asbestos class gasket浸聚四氟乙烯的石棉垫片PTFE impregnated asbestos gasket夹石棉的缠绕金属垫片spiral-wound metal gasket with asbestos filler 内环inner ring外环，外定位环outer ring波纹金属垫片corrugated metal gasket波纹金属包嵌石棉垫片corrugated metal gasket with asbestos inserted 双夹套波纹金属包石棉垫片corrugated metal double jacketed asbestos filled gasket双夹套垫片double jacketed gasket金属包石棉平垫片flat metal jacketed asbestos filled gasket整体金属齿形垫片solid metal serrated gasket槽形金属垫片grooved metal gasket环形连接金属垫片ring joint metal gasket八角环形垫片octagonal ring gasket椭圆环形垫片oval ring gasket透镜式垫片lens gasket非金属垫片non-metallic gasket。
管件中英文对照表
●弯头 elbow异径弯头 reducing elbow带支座弯头 base elbow长半径弯头（标准1.5倍弯曲半径---1.5D）long radius elbow●三通 tee异径三通 reducing tee等径三通 straight tee带侧向口的三通（右向或左向） side outlet tee(right hand or 1eft hand)异径三通（分支口为异径） reducing tee (reducing on outlet)异径三通（一个直通口为异径）reducing tee(reducing on one run)带支座三通 base tee异径三通（一个直通口及分支口为异径） reducing tee (reducing on one run and outlet)异径三通（两个直通口为异径，双头式） reducing tee (reducing on both runs, bull head)45°斜三通 45° lateral45°斜三通（支管为异径） 45° lateral (reducing on branch)45°斜三通(一个直通口为异径) 45° lateral (reducing on one run)45°斜三通(一个直通口及支管为异径) 45° lateral(reducing on one run and branch)Y型三通（俗称裤衩） true “Y”四通 cross等径四通 straight cross异径四通 reducing cross异径四通（一个分支口为异径）reducing cross(reducing on one outlet)异径四通（一个直通口及分支口为异径） reducingcross (reducing on one run and outlet)异径四通（两个分支口为异径） reducing cross(reducing on both outlet)异径四通（一个直通口及两个分支口为异径） reducing cross (reducing on one run and both outlet)异径管 reducer同心异径管 concentric reducer偏心异径管 eccentric reducer锻制异径管 reducing swage螺纹支管台 threadolet焊接支管台 weldolet承插支管台 sockolet弯头支管台 elbolet斜接支管台 latrolet镶入式支管嘴 sweepolet短管支管台 nipolet支管台，插入式支管台 boss●螺纹支管台Threadolet●弯头支管台elbolet●焊接支管台weldolet；on weld●短管支管台nipolet●承插支管台sockolet●烧焊支管台weldolet●斜接支管台latrolet●承插焊支管台Sockolet支管台，插入式支管台boss管接头 coupling, full coupling半管接头 half coupling异径管接头 reducing coupling活接头 union内外螺纹缩接（俗称补芯） bushing管帽 cap (C)堵头 plug短节 nipple异径短节 reducing nipple; swage nipple管道英文缩写A Anchor 固定ABS * Absolute 绝对的AISI *American Iron and Steel Institute美国钢铁学会ANSI * American National Standards Institute 美国国家标准学会API *American Petroleum Institute 美国石油学会APPROX *Approximate 大约，近似的ASB Asbestos 石棉ASME *American Society Of Mechanical Engineers美国机械工程师协会ASSY * Assembly 装配，组装ASTM * American Society Of Testing Material 美国材料实验协会ATM * Atmosphere 大气压AWG * American Wire Gage 美国线规AWS * American Wel**** Society 美国焊接协会AWWA * American Water Works Association 美国水工协会BBB Bolted Bonnet 栓柱连接的阀盖BB By Buyer 买方供货B-B Beveled End-Beveled End 两端为坡口端BC Bolt Circle 螺栓中心圆B.C Bolted Cover(cap) 螺栓连接的阀兰盖（帽）BE Beveled End (for wel****) 坡口（焊接用）B.E Bell End 承口BEP Both Ends Plain 两端平BET Both Ends Threaded 两端带螺纹BL Battery Limit 装置区边界BF Blind Flange 盲板法兰BLD Blind 盲板BLDG *Buil**** 建筑物BM Bill Of Material 材料表BOP Bottom Of Pipe 管底B-P Beveled End —Plain End 坡口端.平端BV Butterfly valve 蝶阀BWG * Birmingham Wire Gage 伯明翰线规BW Butt Weld 对焊CC Cap 管帽C-C Center to Center 中至中C-E Center to End 中至端面C-F Center to Face 中至面CH-OP Chain Operated 链条操纵的CH.PL Checkered Plate 花纹钢管C.I *Cast Iron 铸铁CL *Class 英制压力等级，等级，种类CLEAR Clearance 间隙COD Continued on Drawing 接续图COL *Column 柱，塔CONC Concentric 同心的CONN Connection 连接，接口CONT *Continue 连续CONT.V. Control Valve 控制阀CPLG Coupling 管接头，连轴节C.R. Concentric Reducer 同心异径管C.S. *Carbon Steel 碳钢C.S. Cold Spring 冷紧C.S.C. Car Seal Close 在关闭状态下封住C.S.O. Car Seal Open 在开启状态下封住CUST Customer 客CH Check Valve 止回阀DEG *Degree 度DF Drain funnel 排液漏斗DIA *Diameter 直径DIM *Dimension 尺寸DISCH *Discharge 出口，排出Diaphragm VELVE 隔膜阀DMF Double Male And Female 双重凹凸DN Norminal Diameter公称直径DN Down 下DR Drain 排液DS Directional Stop 定向限为架DWG * Drawing 图EE *East 东EC External Coating 外面涂防腐层ECC Eccentric 偏心EFW Electric Fusion Welded 电容焊的EL(ELEV) *Elevation 标高；立面ELL Elbow 弯头EQIOP Equipment设备，装置EQUIV Equivalent 相当的E.R. Eccentric Reducer 偏心异经管ERW Electric Resistance Welded 电阻焊的EW Eye Washer & Shower 洗眼器及淋浴器EXP.JT Expansion Joint 膨胀节FFDN Foundation基础FF Flat Faced Or Full Faced 全平面；满平面F-F Face To Face 面至面FGW Fusion Gas Wel**** 气熔焊FIG *Figure 图FL Floor 楼面FLEX TUBE Flexible Tube 挠性管FLG Flange 法兰FLGD Flanged 法兰式的FLGF Flanged Face 法兰面FOB Flat On Bottom 底面平FOT Flat On Top 顶面平FP Fix Point 固定点FS Forged Steel 锻钢FTF Fitting To Fitting 管件直连FTG Fitting 管件FURND Furnished 提供的，装设的FW Field Weld 现场焊G Guide 导向GA * Gage 表，表压，规（线规）GALV *Galvanize 镀锌GL Ground Level 地面GLV Globe Valve 截止阀GEAR OP Gear Operated 齿轮传动的GMAW Gas Metal Arc Wel**** 金属极惰气体保护焊GSKT Gasket 垫片GTAW (Inert)Gas Tungsten Arc Wel**** 惰性气体保护钨极电弧焊GV Gate Valve 闸阀HH Hanger 吊架HC Hose Connection 软管接头H.CPLG Half Coupling 半节管接头HDR Header 总管HEX *Hexagon 六角形HF Hard Alloy Face on阀内件（阀心）为Valve Trim 硬质合金密封面HH Hand Hole 手孔HOR Horizontal 水平的H.P * High Pressure 高压HS Hose Station 软管IID * Inside Diameter 内径IN * Inch 英寸INS Insulation 隔热INST Instrument仪表INV Invert (inside bottom of pipe) 管子内底IPS Iron Pipe size 铁管尺寸ISO Isometric Drawing 周测图（空视图）I.S.B.L Inside BatteryLimit 装置边界内恻ISNS Inside screw & Non-rising Stem 内螺纹非升杆ISRS Inside screw & Rising stem 内螺纹升杆JJT Joint 接头JS Jack Screw 顶开（起）螺栓LLC Locked Closed 在关闭状态下锁定LEP Large end plain 大端为平的LET Large end Threaded 大端带螺纹LG Long 长LGF Lens Gasket Face 透镜垫连接面L.H. THD Left Hand Thread 左螺纹LIFT Lift Type 升降式LJ Lap Joint 搭接LJF Lap Joint Flange 松套法兰LO Locked Open 在开启状态下锁定L.P. Low Pressure 低压LR Long Radius 长半径LRE Long Radius Elbow 长半径弯头LTG Large Tongue & Groove 大椎槽MMATL Material 材料MAX Maximum 最大MB Machine Bolt 机器螺栓（单头）MF Male and Female 凸和凹MFG Manufacture 制造MF * Manufacture 制造厂MH Manhole 人孔MI Malleable Iron 可锻铸铁MIN *Minimum 最小MJ Mechanical Joint 机械接头M.L Match Line 连续线MSS * Manufacturers Standardization Society of the Valve and Fittings Industry, Inc. 美国阀门和管件制造商标准化协会MTO Material take-off 材料统计MW Minimum Wall 最小壁厚M.W. Mineral Wool 矿（物）棉NN * North 北NB Nominal Bore 公称孔径N.B. Non-Bonnet 无阀盖NC Normally Closed 常闭NIP Nipple 短管NO Normally Open; 常开*Number号；数量NO INS No Insulation 不隔热NOM Nominal 公称的；额定的NOZ Nozzle 管口NPS Nominal Pipe Size 公称管径NPSH Net Positive Suction Head 净正吸入压头NPT *American National Taper 美国锥管螺纹Pipe ThreadNS Nominal Size 公称直径NV Needle Valve 针形阀OOD *Outside Diameter 外径OET One end Threaded 一端带螺纹OR Outside Radius 外半径ORF Orifice 孔板ORIENT Orientation 方位OS & Y Outside Screw and Yoke 外螺纹阀杆和阀轭OSNB Outside Screw Non-Bonnet 外螺纹无阀盖PP Plug 堵头PAP Piping Arrangement Plan管道布置平面图PB Pressure Seal Bonnet 压力密封的阀盖P-B Plain End –Bevel End 平端—坡口端PC Pressure Seal Cap 压力密封的阀。
管件中英文对照表
管件中英文对照表Filter 过滤器No period of seamless hot-pressing elbow straight 无直段无缝热压弯头Butt plug 对焊堵头concentric reducer 大小头Welding plug 焊接堵头钢管模压大小头Steel pipe mold size head锻制等径三通Forged equal tee钢管模压异径管Steel pipe moulding reducer无缝热压弯头Seamless hot-pressing elbow锻制异径三通Forging reducing teewater flow indicator 水流指示器不锈钢大小头Stainless steel reducer热压等径三通Hot-pressing equal tee不锈钢无直管段无缝热压弯头Stainless steel seamless hot-pressing elbow straight pipe不锈钢热压等径三通Stainless steel hot-pressing equal tee不锈钢热压异径三通Stainless steel hot-pressing reducing tee不锈钢无缝热压弯头Stainless steel seamless hot-pressing elbow不锈钢偏心异径管Stainless steel eccentric reduce不锈钢同心异径管Stainless steel concentric reducer不锈钢钢板焊制异径管Stainless steel plate welded reducer方圆形排水漏斗Fangyuan drainage funnel钢板焊制异径管The steel plate welded reducer接管座Take over seatwater flo w indicator 水流指示器Circular cone 圆形漏斗Funnel (with cover) 漏斗（带盖）Fangyuan drainage funnel Thermal pressure reducing tee 热压异径三通。
管件中英文对照
管件中英文对照(20０7-07－15 1１:４2：00)等径直通eｑual couplｉnｇ异径直通redｕcing coｕpling ﻫ内牙直通 female couplｉng外牙直通 straighｔ tube wｉth outｓidｅﻫ90等径弯头 9０ eｑｕa ｌ elbow４5等径弯头 45 equal elbow外牙弯头 male elbow ﻫ内牙弯头 female ｅlbｏw等径三通 eｑｕal ｔee异径三通 reｄuｃing tee ﻫ内牙三通ｆemaｌｅｔeｅﻫ外牙三通 mａl ｅｔee管帽cap ﻫsch代表压力lr长半径或１倍半ﻫ大小 SＩＺE ﻫ数量ＱＴY ﻫ碳钢弯头Ｃaｒｂo ｎ Steel Ｅｌbow ﻫ不锈钢弯头Ｓtainleｓs Sｔeｅl Elbow ﻫ高压弯头 H ｉｇh-Presｓurｅ Eｌbow同心异径管 Cｏnceｎtric Reｄｕcerｓﻫ偏心异径管 Eccｅntrｉc Ｒeｄｕｃeｒs ﻫ高压异径管Ｈigh-pｒesｓｕｒe Reduceｒs不锈钢等径三通 Sｔaｉnless Strａiｇhｔ Tee碳钢等径三通Ｃarｂoｎ Straighｔ Tee ﻫ不锈钢等径四通Ｓtaiｎlｅｓs St ｒaigｈt Cross ﻫ高压三通 Higｈ-pressure Teｅﻫ锻制三通 Fｏrged Te ｅﻫ异径接头Ｔｅmplａte管帽 Caｐs法兰fｌange长径和短径弯头 long and short radius eｌboｗｓﻫ同心和偏心异径接头 concenｔrｉｃ and ecceｎtric reducers等径和异径三通ｓtraigｈt and reduｃiｎg ｏutlet tees大小头 CONCＥNTRＩC ＲEDUCER ﻫＴee Equal 相等的三通ﻫ等径三通Ｓtｒaigｈt Tee异径三通Redｕｃiｎg Teｅﻫ等径四通Stｒaight Ｃrｏss９０°短半径弯头90°ＳS Ｅlｂow (ＳＲ）90°长半径弯头９0°ＳS Eｌbow （LＲ) ﻫ高压厚壁弯头Ｔhｉｃkｎeｓｓ Elｂow ﻫU型管Retuｒn Bend盲法兰Blａnk Fｌange弯管Bｅｎds翻边stub ｅnds ﻫ异径接头ｒedｕcers ﻫ公称通径 nominal ｄiaｍete ｒﻫ外径（mm) ouｔｓide diamｅter ﻫ中心距至端面的距离ｃenteｒ t ｏｅnd理论重量(kｇ/pcs) aｐprox weｉght ﻫｄｅｓcrｉptｉoｎ类种ﻫSｔandard标准ﻫDesign类型ﻫMaterｉａｌ材质ﻫ双丝头 Nipplｅﻫ短节 SＷＡGE ＮIＰPLE ﻫ内外螺纹活接头 Unioｎ螺桩 stｕｄHalｆ－Coupｌｉng单承口管箍Cｏuplｉｎg双承口管箍ﻫ盲板Ｂｌind Flａngｅﻫspecｔaｃle bｌｉnd 带双圈的盲板ﻫＥceｎtrｉｃ偏心的拆除：ｄismaｎtle结头（管线的)：tie－ｉn ﻫ插盲板：sｌip spaｄe盲板：bｌank ﻫ接头：fittｉng ﻫ加热器：heaｔer ﻫ金属缠绕垫片（带外环)：ＳＷ wｉth ｏutside rinｇﻫHR：热轧ﻫﻫ 1 总则ﻫﻫ1.1为了确保压力管道设计质量,规范压力管道配管术语,特制定本规定。
管件中英文对照
管件中英文对照表 (常用)
碳钢弯头 Carbon Steel Elbow不锈钢弯头 Stainless Steel Elbow高压弯头 High—Pressure Elbow同心异径管 Concentric Reducers偏心异径管 Eccentric Reducers高压异径管 High—pressure Reducers不锈钢等径三通 Stainless Straight Tee碳钢等径三通 Carbon Straight Tee不锈钢等径四通 Stainless Straight Cross高压三通 High—pressure Tee锻制三通 Forged Tee异径接头 Template 管帽 Caps 法兰flange长径和短径弯头 long and short radius elbows同心和偏心异径接头 concentric and eccentric reducers等径和异径三通 straight and reducing outlet tees大小头 CONCENTRIC REDUCER相等的三通Tee Equal等径三通Straight Tee异径三通Reducing Tee等径四通Straight Cross90°短半径弯头90°SS Elbow(SR) U型管Return Bend90°长半径弯头90°SS Elbow (LR)高压厚壁弯头Thickness Elbow盲法兰Blank Flange 弯管Bends翻边stub ends 异径接头reducers 公称通径 nominal diameter外径(mm) outside diameter 中心距至端面的距离center to end理论重量（kg/pcs) approx weight类种description 标准Standard类型Design 材质Material 双丝头 Nipple同心异径短节 SWAGE Nipple活接头 Union PLUG HEX HEAD六角管堵 PLUG HEX HEADSCRD六角螺纹管堵MPT螺纹 RC螺纹螺桩 stud SWAGE (CONC）同心异径短节单承口管箍 Half—Coupling 异径管箍Coupling, Reducing盲板 Blind Flange 带双圈的盲板spectacle blind 偏心的Ecentric 等径直通equal coupling内牙直通 female coupling外牙直通 straight tube with outside90等径弯头 90 equal elbow45等径弯头 45 equal elbow外牙弯头 male elbow内牙弯头 female elbow 等径三通 equal tee异径三通 reducing tee内牙三通female tee外牙三通 male tee 管帽cap拆除:dismantle 结头(管线的）：tie-in插盲板:slip spade 盲板:blank接头：fitting 加热器：heater金属缠绕垫片（带外环）:SW with outside ring 热轧on site: 管汇manifold3。
- 1、下载文档前请自行甄别文档内容的完整性，平台不提供额外的编辑、内容补充、找答案等附加服务。
- 2、"仅部分预览"的文档,不可在线预览部分如存在完整性等问题,可反馈申请退款(可完整预览的文档不适用该条件!)。
- 3、如文档侵犯您的权益，请联系客服反馈,我们会尽快为您处理(人工客服工作时间：9:00-18:30)。
管件中英文对照管件中英文对照等径直通equal coupling 异径直通reducing coupling 内牙直通female coupling 夕卜牙直通straight tube with outside 90 等径弯头90 equal elbow 45 等径弯头45 equal elbow 夕卜牙弯头male elbow 内牙弯头female elbow 等径三通equal tee 异径三通reducing tee 内牙三通female tee 夕卜牙三通male tee 管帽cap sch代表压力lr长半径或1倍半大小SIZE 数量QTY碳钢弯头Carbon Steel Elbow 不锈钢弯头Stainless Steel Elbow 高压弯头High-Pressure Elbow 同心异径管Concentric Reducers 偏心异径管Eccentric Reducers 高压异径管High-pressure Reducers 不锈钢等径三通Stai nless Straight Tee 碳钢等径三通Carbo n Straight Tee 不锈钢等径四通Sta in less Straight Cross 高压三通High-pressure Tee 锻制三通Forged Tee 异径接头Template 管帽Caps 法兰flange 长径和短径弯头long and short radius elbows 同心和偏心异径接头concen tric and ecce ntric reducers等径和异径三通straight and reduc ing outlet tees大小头CONCENTRIC REDUCER Tee Equal相等的三通等径三通Straight Tee异径三通Reduc ing Tee等径四通Straight Cross90。
短半径弯头90 °SS Elbow (SR) 90。
长半径弯头90 °SS Elbow (LR) 高压厚壁弯头Thick ness ElbowU 型管Return Bend盲法兰Bla nk Fla nge弯管Bends 翻边stub ends 异径接头reducers公称通径nominal diameter 夕卜径（mm） outside diameter 中心距至端面的距离ce nter to end 理论重量（kg/pcs）approx weight descripti on 类禾申Sta ndard 标准Design 类型Material 材质双丝头Nipple 短节SWAGE NIPPLE 内外螺纹活接头Union 螺桩stud Half-Coupli ng 单承口管箍Coupling双承口管箍盲板Blind Flange spectacle bli nd 带双圈的盲板Ecen tric 偏心的拆除:disma ntle 结头（管线的）：tie-in 插盲板：slip spade 盲板：blank 接头：fitting 力口热器：heater 金属缠绕垫片（带外环）:SW with outside ringHR:热轧on site:manifold:管7匚1.2管件Fitting弯头elbow异径弯头reducing elbow 带支座弯头base elbow k半径弯头long radius elbow短半径弯头short radius elbow长半径180。
弯头long radius return短半径180。
弯头short radiusreturn带侧向口的弯头（右向或左向）side outlet elbow （right hand or lefthand）双支管弯头（形）double branch elbow三通tee异径三通reducing tee等径三通straight tee带侧向口的三通（右向或左向）side outlet tee （right hand or 1eft hand）异径三通（分支口为异径）reduc ing tee （reduc ing on outlet）异径三通（一个直通口为异径）reduc ing tee （reduc ing on one run）带支座三通base tee异径三通（一个直通口及分支口为异径）reduc ing tee （reduc ing on one runandoutlet）异径三通（两个直通口为异径，双头式）reduc ing tee （reduc ing on both runs,bull head）45 斜三通45 ° lateral45斜三通（支管为异径）45°lateral （reduc ing on bran ch）45斜三通（一个直通口为异径）45 ° lateral （reducing on one run）45斜三通（一个直通口及支管为异径）45 ° lateral （reducing on one run andbran ch）Y型三通（俗称裤衩）true“ Y”四通cross等径四通straight cross异径四通reducing cross 异径四通（一个分支口为异径）reduc ing cross （reduc ing on one outlet）异径四通（一个直通口及分支口为异径) reduc ing cross (reduc ing on onerunand outlet)异径四通(两个分支口为异径) reduc ing cross (reduc ing on both outlet)异径四通(一个直通口及两个分支口为异径) reduc ing cross (reduc ing onone runand both outlet)异径管reducer同心异径管concen tricreducer偏心异径管ecce ntricreducer锻制异径管reduc ing swage螺纹支管台threadolet焊接支管台weldolet承插支管台sockolet弯头支管台elbolet斜接支管台latrolet镶入式支管嘴sweepolet 短管支管台nipolet支管台，插入式支管台boss管接头coupling, fullcoupli ng半管接头half coupling 异径管接头reduc ing coupli ng活接头union内外螺纹缩接（俗称补芯）bushi ng管帽cap （C）堵头plug短节nipple异径短节reducing nipple; swage n ipple1 管道组成件Pip ing comp onent1.1 管子Pipe管子（按照配管标准规格制造的）pipe 管子（不按配管标准规格制造的其他用管）tube 钢管steel pipe铸铁管cast iron pipe衬里管lined pipe复合管clad pipe碳钢管carb on steel pipe合金钢管alloy steel pipe不锈钢stainless steel pipe奥氏体不锈钢管auste nitic stai nless steel pipe 铁合金钢管ferritic alloy steel pipe 车L制钢管wrought-steel pipe锻铁管wrought-iron pipe无缝钢管seamless (SMLS) steel pipe焊接钢管welded steel pipe电阻焊钢管electric-resista nee welded steel pipe电熔(弧)焊钢板卷管eleetrie-fusio n(are)-welded steel-plate pipe螺旋焊接钢管spiral welded steel pipe 镀锌钢管galvanized steel pipe 热轧无缝钢管hot-rolli ng seamless pipe 冷拔无缝钢管eold-drawi ng seamless pipe 水煤气钢管water-gas steel pipe 塑料管plastie pipe 玻璃管glass tube 橡胶管rubber tube 直管run pipe; straight pipe1.2管件Fitting 弯头elbow 异径弯头redueing elbow 带支座弯头base elbow k 半径弯头long radius elbow 短半径弯头short radius elbow 长半径180° 弯头long radius return 短半径180° 弯头short radius return 带侧向口的弯头(右向或左向) side outlet elbow （right hand or left hand）双支管弯头（形）double branch elbow 三通tee异径三通reducing tee等径三通straight tee带侧向口的三通（右向或左向）side outlet tee（right hand or left hand）异径三通（分支口为异径）reduc ing tee（reduc ing on outlet）异径三通（一个直通口为异径）reduc ing tee（reduc ing on one run）带支座三通base tee异径三通（一个直通口及分支口为异径）reduc ing tee （reduc ing on one run and outlet）异径三通（两个直通口为异径，双头式）reducingtee （reduc ing on both runs, bull head）45。
斜三通45 ° lateral45 °斜三通（支管为异径）45° lateral （reducingon bran ch）45。
斜三通（一个直通口为异径）45 lateral（reduc ing on one run）45。
斜三通（一个直通口及支管为异径）45 lateral （reduc ing on one run and bran ch）Y型三通（俗称裤衩）true “ Y”四通cross等径四通straight cross异径四通reducing cross异径四通(一个分支口为异径) reduc ing cross (reduc ing on one outlet)异径四通(一个直通口及分支口为异径) reduc ing cross (reduc ing on one run and outlet)异径四通(两个分支口为异径) reduc ing cross (reduc ing on both outlet)异径四通(一个直通口及两个分支口为异径) reduc ing cross (reduc ing on one run and both outlet)异径管reducer 同心异径管concentric reducer 偏心异径管eccentric reducer 锻制异径管reducing swage 螺纹支管台threadolet 焊接支管台weldolet 承插支管台sockolet 弯头支管台elbolet 斜接支管台latrolet 镶入式支管嘴sweepolet 短管支管台nipolet 支管台.插入式支管台boss 管接头coupling, full coupling 半管接头half coupling 异径管接头reducing coupling 活接头union内外螺纹缩接（俗称补芯）bush ing管帽cap （C）堵头plug短节nipple异径短节reducing nipple; swage nipple1.3弯管Be nd预制弯管fabricated pipe bend 跨越弯管（八形）cross-over bend 偏置弯管（~形）offset bend90。