美孚润滑油MSDS
美孚润滑油安全数据信息表
美孚润滑油安全数据信息表1. 产品概述美孚润滑油是一种高质量的润滑油产品，广泛应用于各种机械设备和汽车引擎中。
本文档将提供有关美孚润滑油的安全数据信息。
2. 安全数据信息2.1. 物理性质- 外观：透明液体- 颜色：琥珀色- 气味：特殊气味- 熔点：-30°C- 沸点：> 300°C- 相对密度：0.85 g/mL- 溶解性：不溶于水2.2. 燃烧性质- 火灾爆炸危险性：低- 火灾扩散性：不适用- 火灾爆炸特性：不适用- 着火温度：> 200°C- 自燃温度：不适用- 爆炸极限：不适用2.3. 环境影响- 生态毒性：对水环境有害- 生物降解性：不易生物降解- 生物富集性：不适用2.4. 健康和安全- 吸入：可能引起呼吸道刺激- 食入：可能引起胃肠道刺激- 眼睛接触：可能引起眼睛刺激- 皮肤接触：可能引起皮肤刺激- 毒理学信息：根据相关法规进行操作和处理3. 预防措施为了确保使用美孚润滑油的安全性，以下预防措施应被采取：- 避免长时间或频繁接触美孚润滑油- 在使用美孚润滑油时，应戴上适当的个人防护装备，如手套和护目镜- 在使用美孚润滑油时，应确保操作场所通风良好- 避免美孚润滑油进入水源或土壤中- 在使用美孚润滑油后，应正确处置废弃物4. 应急措施在发生美孚润滑油泄漏或事故时，应采取以下应急措施：- 尽量避免直接接触泄漏物- 使用合适的吸收剂将泄漏物吸附- 在清理泄漏物时，确保操作场所通风良好- 使用防爆设备和个人防护装备进行清理工作- 遵循当地法规和规定，正确处置泄漏物和废弃物以上是关于美孚润滑油的安全数据信息。
使用前请详细阅读产品标签和安全说明，遵循正确的操作和处理方法，以确保人员和环境的安全。
参考资料：- 美孚润滑油产品说明书- 相关法规和规定。
63# MOBIL VELOCITE OIL NO. 3物料安全数据(MSDS)
页 1 of 9______________________________________________________________________________________________________________________产品安全技术说明书这一产品安全技术说明书为中国而编制。
产品产品名称: MOBIL VELOCITE OIL NO. 3产品简介: 烃类及添加剂产品代码: 600643特定用途: 润滑油公司资料供应商: 埃克森美孚( 中国 )投资有限公司美罗大厦17楼天钥桥路30号上海市 200030 中国供应商联系电话 86-21-24076000该材料被规定为一种制剂。
* 除气体外，所有组分的浓度均为重量百分比。
气体浓度采用体积百分比。
根据法规指引(参阅第十五部分)，该物料被认为有害。
欧盟标准分类: | Xn; R65 | R66 |GB 13690-92 常用危险化学品的分类未被定为危险品。
物理/化学危害该物料会释放蒸气形成可燃性混合气体，蒸气积聚若被点燃会闪火或爆炸健康危害页 2 of 9______________________________________________________________________________________________________________________ 有害：若误吞会对肺造成损害。
反复接触可能使皮肤干燥或龟裂。
可能会刺激眼、鼻、喉及肺。
皮肤下高压注射可能会引起严重损伤。
注意: 在没有咨询专家的情况下,除第1部分规定的特定用途外,该产品不可用于其它任何目的。
健康研究已经表明,化学接触可能对人体健康造成潜在危害,这一点因人而异。
吸入避免进一步吸入接触。
对于那些提供帮助的人员,应使您或者其他人避免吸入。
进行充分的呼吸防护。
如果出现呼吸刺激、头昏、恶心、或者神志不清,请立刻就医。
如果呼吸停止,请使用机械设备帮助通风,或者进行嘴对嘴人工呼吸急救。
美孚力士滑脂EP物料安全数据表(MSDS)
化学类别
复合锂基脂
主要用途
润滑
健康危害
无
环境影响 危害辨 物理及化学性危害 识的数
据 主要症状
无 皮肤刺激 红肿
物品危险性类别
/
所需图示种类
/
皮肤接触
使用肥皂及清水冲洗
急救 措施
眼睛接触 食入 吸入
用大量清水冲洗 无影向,如多于0.5公升,求医 无影向
给医生的建议
/
灭火 措施
适用灭火剂
喷雾水,泡沫,干粉及二氧化碳,
/ / /
危害之分解产物
/
毒性 急毒性或生殖毒性
资料 慢毒性或长期毒性
生态 废资弃料处 理办法
可能的环境影响 废弃处理办法
包装分类
/ / 注意不能排出污染物 燃烧或循环再用 桶装
运送 资料
运送 资料
法规 资料
其他 数据
包装标志 包装方法 搁置期限 适用法规 标识信息 R警告语 S警告语 参考文献 资料整理人 整理日期 文件版本号 编号 保存期限
灭火时可能遇到的特殊
危害
/
灭火方法
/
储运 储存要求 资料 搬运要求
通风阴凉处 不要使容器损坏或淋湿以免污染润滑油
个人注意事项
泄漏处 理方法
环境注意事项
尽量使皮臛或眼睛不去接触润滑油 不要把废油倒在水沟里或公众地方
处理办法
燃烧
车间浓度控制标准（参
考）
/
工程控制措施
/
呼吸系统防护
/
手防护
/
暴露预 防措施
面部防护
/
皮肤及身体防护
/
眼睛防护
/
其他
/
卫生措施
美孚喷气发动机油2号安全数据表说明书
修订日期: 28 四月 2019 SDS 编号:2003056XCN最初编制日期: 11 Sep 2015 版本:3.02______________________________________________________________________________________________________________________化学品安全技术说明书产品产品名称: 美孚喷气发动机油2号产品简介:合成酯类及添加剂产品代码: 201550101020, 430207推荐用途: 飞行润滑油, 汽轮机油公司资料供应商:埃克森美孚( 中国 )投资有限公司美罗大厦17楼天钥桥路30号上海市 200030 中国二十四小时应急电话供应商联系电话电子邮件传真 400 1200 526紧急情况概述:物理状态: 液体颜色: 琥珀色气味: 特有的根据法规指引（参阅第十五部分)，本产品不属于危险品。
高压射向皮肤可能会造成严重的损伤正常状况下配合良好的个人卫生习惯使用本产品时，不预期会对健康产生损害。
本产品会在温度升高或遇到明火的情况下产生分解，同时释放出刺激性和/或有害的(一氧化碳)气体/蒸气/烟雾。
在密闭空间内急性接触这些分解产物的症状包括头疼，恶心，对眼，鼻和咽喉的刺激。
根据法规指引（参阅第十五部分)，本产品不属于危险品。
修订日期: 28 四月 2019 SDS 编号:2003056XCN最初编制日期: 11 Sep 2015 版本:3.02______________________________________________________________________________________________________________________含有: N - 苯基 -1 - 萘胺可能产生过敏反应。
其它危险性信息:物理/化学危害无明显危害健康危害高压射向皮肤可能会造成严重的损伤正常状况下配合良好的个人卫生习惯使用本产品时，不预期会对健康产生损害。
润滑油化学品安全技术说明书(MSDS)
润滑油安全技术说明书（MSDS）第一部分：化学品及企业标识化学品中文名称：润滑油化学品英文名称：lubricating oil中文名称2：机油英文名称2：Lube oil 技术说明书编码：1279供应商名称：供应商地址：供应商联系方式：第二部分：成分/组成信息有害物成分：无含量：0CAS No.：分子式：分子量：230-500第三部分：危险性概述危险性类别：侵入途径：健康危害：急性吸入，可出现乏力、头晕、头痛、恶心，严重者可引起油脂性肺炎。
慢接触者，暴露部位可发生油性痤疮和接触性皮炎。
可引起神经衰弱综合征，呼吸道和眼刺激症状及慢性油脂性肺炎。
有资料报道，接触石油润滑油类的工人，有致癌的病例报告。
环境危害：燃爆危险：本品可燃，具刺激性。
第四部分：急救措施皮肤接触：脱去污染的衣着，用大量流动清水冲洗。
就医。
眼睛接触：提起眼睑，用流动清水或生理盐水冲洗。
就医。
吸入：迅速脱离现场至空气新鲜处。
保持呼吸道通畅。
如呼吸困难，给输氧。
如呼吸停止，立即进行人工呼吸。
就医。
食入：饮足量温水，催吐。
就医。
第五部分：消防措施危险特性：遇明火、高热可燃。
有害燃烧产物：一氧化碳、二氧化碳。
灭火方法：消防人员须佩戴防毒面具、穿全身消防服，在上风向灭火。
尽可能将容器从火场移至空旷处。
喷水保持火场容器冷却，直至灭火结束。
处在火场中的容器若已变色或从安全泄压装置中产生声音，必须马上撤离。
灭火剂：雾状水、泡沫、干粉、二氧化碳、砂土。
第六部分：泄漏应急处理应急处理：迅速撤离泄漏污染区人员至安全区，并进行隔离，严格限制出入。
切断火源。
建议应急处理人员戴自给正压式呼吸器，穿防毒服。
尽可能切断泄漏源。
防止流入下水道、排洪沟等限制性空间。
小量泄漏：用砂土或其它不燃材料吸附或吸收。
大量泄漏：构筑围堤或挖坑收容。
用泵转移至槽车或专用收集器内，回收或运至废物处理场所处置。
第七部分：操作处置与储存操作注意事项：密闭操作，注意通风。
操作人员必须经过专门培训，严格遵守操作规程。
埃克森美孚Mobil Delvac极限服役润滑脂 MSDS说明书
Page 1 of 8______________________________________________________________________________________________________________________ MATERIAL SAFETY DATA SHEETPRODUCTProduct Name: MOBIL DELVAC XTREME SERVICE GREASEProduct Description:Base Oil and AdditivesProduct Code: 2015A020F010, 530089-00, 97M078Intended Use: GreaseCOMPANY IDENTIFICATIONSupplier: EXXON MOBIL CORPORATION3225 GALLOWS RD.FAIRFAX, VA. 22037 USA24 Hour Health Emergency 609-737-4411Transportation Emergency Phone 800-424-9300ExxonMobil Transportation No. 281-834-3296MSDS Requests 713-613-3661Product Technical Information 800-662-4525, 800-947-9147MSDS Internet Address , * All concentrations are percent by weight unless material is a gas. Gas concentrations are in percent by volume.This material is not considered to be hazardous according to regulatory guidelines (see (M)SDS Section 15). POTENTIAL HEALTH EFFECTSLow order of toxicity. Excessive exposure may result in eye, skin, or respiratory irritation. High-pressure injection under skin may cause serious damage.NFPA Hazard ID:Health: 0 Flammability: 1 Reactivity: 0HMIS Hazard ID:Health: 0 Flammability: 1 Reactivity: 0NOTE: This material should not be used for any other purpose than the intended use in Section 1 without expert advice. Health studies have shown that chemical exposure may cause potential human health risks which may vary from person to person.Page 2 of 8______________________________________________________________________________________________________________________ INHALATIONUnder normal conditions of intended use, this material is not expected to be an inhalation hazard.SKIN CONTACTWash contact areas with soap and water. If product is injected into or under the skin, or into any part of the body, regardless of the appearance of the wound or its size, the individual should be evaluated immediately bya physician as a surgical emergency. Even though initial symptoms from high pressure injection may beminimal or absent, early surgical treatment within the first few hours may significantly reduce the ultimate extent of injury.EYE CONTACTFlush thoroughly with water. If irritation occurs, get medical assistance.INGESTIONFirst aid is normally not required. Seek medical attention if discomfort occurs.EXTINGUISHING MEDIAAppropriate Extinguishing Media: Use water fog, foam, dry chemical or carbon dioxide (CO2) to extinguish flames.Inappropriate Extinguishing Media: Straight Streams of WaterFIRE FIGHTINGFire Fighting Instructions: Evacuate area. Prevent runoff from fire control or dilution from entering streams, sewers, or drinking water supply. Firefighters should use standard protective equipment and in enclosedspaces, self-contained breathing apparatus (SCBA). Use water spray to cool fire exposed surfaces and toprotect personnel.Hazardous Combustion Products: Aldehydes, Smoke, Fume, Sulfur oxides, Incomplete combustionproducts, Oxides of carbonFLAMMABILITY PROPERTIESFlash Point [Method]: >204C (400F) [ EST. FOR OIL, ASTM D-92 (COC)]Flammable Limits (Approximate volume % in air): LEL: N/D UEL: N/DAutoignition Temperature: N/DNOTIFICATION PROCEDURESIn the event of a spill or accidental release, notify relevant authorities in accordance with all applicableregulations. U.S. regulations require reporting releases of this material to the environment which exceed thereportable quantity or oil spills which could reach any waterway including intermittent dry creeks. The National Response Center can be reached at (800)424-8802.Page 3 of 8______________________________________________________________________________________________________________________ SPILL MANAGEMENTLand Spill: Scrape up spilled material with shovels into a suitable container for recycle or disposal.Water Spill: Stop leak if you can do it without risk. Confine the spill immediately with booms. Warn other shipping. Skim from surface.Water spill and land spill recommendations are based on the most likely spill scenario for this material;however, geographic conditions, wind, temperature, (and in the case of a water spill) wave and current direction and speed may greatly influence the appropriate action to be taken. For this reason, local experts should be consulted. Note: Local regulations may prescribe or limit action to be taken.ENVIRONMENTAL PRECAUTIONSPrevent entry into waterways, sewers, basements or confined areas.HANDLINGPrevent small spills and leakage to avoid slip hazard.Static Accumulator: This material is not a static accumulator.STORAGEDo not store in open or unlabelled containers.EXPOSURE LIMIT VALUESNOTE: Limits/standards shown for guidance only. Follow applicable regulations.ENGINEERING CONTROLSThe level of protection and types of controls necessary will vary depending upon potential exposure conditions.Control measures to consider:No special requirements under ordinary conditions of use and with adequate ventilation. PERSONAL PROTECTIONPersonal protective equipment selections vary based on potential exposure conditions such as applications,handling practices, concentration and ventilation. Information on the selection of protective equipment for use with this material, as provided below, is based upon intended, normal usage.Respiratory Protection: If engineering controls do not maintain airborne contaminant concentrations at a level which is adequate to protect worker health, an approved respirator may be appropriate. Respiratorselection, use, and maintenance must be in accordance with regulatory requirements, if applicable. Types of respirators to be considered for this material include:No protection is ordinarily required under normal conditions of use and with adequate ventilation.Page 4 of 8______________________________________________________________________________________________________________________ For high airborne concentrations, use an approved supplied-air respirator, operated in positive pressure mode.Supplied air respirators with an escape bottle may be appropriate when oxygen levels are inadequate,gas/vapor warning properties are poor, or if air purifying filter capacity/rating may be exceeded.Hand Protection: Any specific glove information provided is based on published literature and glovemanufacturer data. Work conditions can greatly effect glove durability; inspect and replace worn or damaged gloves. The types of gloves to be considered for this material include:No protection is ordinarily required under normal conditions of use.Eye Protection: If contact is likely, safety glasses with side shields are recommended.Skin and Body Protection: Any specific clothing information provided is based on published literature or manufacturer data. The types of clothing to be considered for this material include:No skin protection is ordinarily required under normal conditions of use. In accordance with goodindustrial hygiene practices, precautions should be taken to avoid skin contact.Specific Hygiene Measures: Always observe good personal hygiene measures, such as washing afterhandling the material and before eating, drinking, and/or smoking. Routinely wash work clothing and protective equipment to remove contaminants. Discard contaminated clothing and footwear that cannot be cleaned.Practice good housekeeping.ENVIRONMENTAL CONTROLSSee Sections 6, 7, 12, 13.Typical physical and chemical properties are given below. Consult the Supplier in Section 1 for additional data.GENERAL INFORMATIONPhysical State: SolidForm: Semi-fluidColor: OrangeOdor: CharacteristicOdor Threshold: N/DIMPORTANT HEALTH, SAFETY, AND ENVIRONMENTAL INFORMATIONRelative Density (at 15 C ): 0.908Flash Point [Method]: >204C (400F) [ EST. FOR OIL, ASTM D-92 (COC)]Flammable Limits (Approximate volume % in air): LEL: N/D UEL: N/DAutoignition Temperature: N/DBoiling Point / Range: > 316C (600F)Vapor Density (Air = 1): N/DVapor Pressure: < 0.013 kPa (0.1 mm Hg) at 20 CEvaporation Rate (n-butyl acetate = 1): N/DpH: N/ALog Pow (n-Octanol/Water Partition Coefficient): > 3.5Solubility in Water: NegligibleViscosity: 320 cSt (320 mm2/sec ) at 40 COxidizing Properties:See Sections 3, 15, 16.Page 5 of 8______________________________________________________________________________________________________________________ OTHER INFORMATIONFreezing Point: N/DMelting Point: 260°C (500°F)DMSO Extract (mineral oil only), IP-346: < 3 %wtNOTE: Most physical properties above are for the oil component in the material.STABILITY: Material is stable under normal conditions.CONDITIONS TO AVOID: Excessive heat. High energy sources of ignition.MATERIALS TO AVOID: Strong oxidizersHAZARDOUS DECOMPOSITION PRODUCTS: Material does not decompose at ambient temperatures. HAZARDOUS POLYMERIZATION: Will not occur.CHRONIC/OTHER EFFECTSContains:Base oil severely refined: Not carcinogenic in animal studies. Representative material passes IP-346, Modified Ames test, and/or other screening tests. Dermal and inhalation studies showed minimal effects; lungnon-specific infiltration of immune cells, oil deposition and minimal granuloma formation. Not sensitizing in test animals.Additional information is available by request.Page 6 of 8______________________________________________________________________________________________________________________ The following ingredients are cited on the lists below:None.--REGULATORY LISTS SEARCHED--1 = NTP CARC 3 = IARC 1 5 = IARC 2B2 = NTP SUS 4 = IARC 2A 6 = OSHA CARCThe information given is based on data available for the material, the components of the material, and similar materials. ECOTOXICITYMaterial -- Not expected to be harmful to aquatic organisms.MOBILITYBase oil component -- Low solubility and floats and is expected to migrate from water to the land.Expected to partition to sediment and wastewater solids.PERSISTENCE AND DEGRADABILITYBiodegradation:Base oil component -- Expected to be inherently biodegradableBIOACCUMULATION POTENTIALBase oil component -- Has the potential to bioaccumulate, however metabolism or physical properties may reduce the bioconcentration or limit bioavailability.Disposal recommendations based on material as supplied. Disposal must be in accordance with current applicable laws and regulations, and material characteristics at time of disposal.DISPOSAL RECOMMENDATIONSProduct is suitable for burning in an enclosed controlled burner for fuel value or disposal by supervisedincineration at very high temperatures to prevent formation of undesirable combustion products. REGULATORY DISPOSAL INFORMATIONRCRA Information: The unused product, in our opinion, is not specifically listed by the EPA as a hazardous waste (40 CFR, Part 261D), nor is it formulated to contain materials which are listed as hazardous wastes. It does not exhibit the hazardous characteristics of ignitability, corrositivity or reactivity and is not formulated with contaminants as determined by the Toxicity Characteristic Leaching Procedure (TCLP). However, usedproduct may be regulated.Empty Container Warning PRECAUTIONARY LABEL TEXT: Empty containers may retain residue and can be dangerous. DO NOT PRESSURIZE, CUT, WELD, BRAZE, SOLDER, DRILL, GRIND OR EXPOSE SUCH CONTAINERS TO HEAT, FLAME, SPARKS, STATIC ELECTRICITY, OR OTHER SOURCES OF IGNITION; THEY MAY EXPLODE AND CAUSE INJURY OR DEATH. Do not attempt to refill or clean container since residue is difficult to remove. Empty drums should be completely drained, properly bunged and promptly returned to a drumPage 7 of 8______________________________________________________________________________________________________________________ reconditioner. All containers should be disposed of in an environmentally safe manner and in accordance with governmental regulations.LAND (DOT) : Not Regulated for Land TransportLAND (TDG) : Not Regulated for Land TransportSEA (IMDG) : Not Regulated for Sea Transport according to IMDG-CodeAIR (IATA) : Not Regulated for Air TransportOSHA HAZARD COMMUNICATION STANDARD: When used for its intended purposes, this material is not classified as hazardous in accordance with OSHA 29 CFR 1910.1200.NATIONAL CHEMICAL INVENTORY LISTING: TSCAEPCRA:This material contains no extremely hazardous substances.SARA (311/312) REPORTABLE HAZARD CATEGORIES: None.--REGULATORY LISTS SEARCHED--1 = ACGIH ALL 6 = TSCA 5a2 11 = CA P65 REPRO 16 = MN RTK2 = ACGIH A1 7 = TSCA 5e 12 = CA RTK 17 = NJ RTK3 = ACGIH A2 8 = TSCA 6 13 = IL RTK 18 = PA RTK4 = OSHA Z 9 = TSCA 12b 14 = LA RTK 19 = RI RTK5 = TSCA 4 10 = CA P65 CARC 15 = MI 293Code key: CARC=Carcinogen; REPRO=ReproductivePage 8 of 8______________________________________________________________________________________________________________________ * EPA recently added new chemical substances to its TSCA Section 4 test rules. Please contact the supplier to confirm whether the ingredients in this product currently appear on a TSCA 4 or TSCA 12b list.THIS SAFETY DATA SHEET CONTAINS THE FOLLOWING REVISIONS:No revision information is available.----------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------The information and recommendations contained herein are, to the best of ExxonMobil's knowledge and belief, accurate and reliable as of the date issued. You can contact ExxonMobil to insure that this document is the most current available from ExxonMobil. The information and recommendations are offered for the user's consideration and examination. It is the user's responsibility to satisfy itself that the product is suitable for the intended use. If buyer repackages this product, it is the user's responsibility to insure proper health, safety and other necessary information is included with and/or on the container. Appropriate warnings and safe-handling procedures should be provided to handlers and users. Alteration of this document is strictly prohibited. Except to the extent required by law,re-publication or retransmission of this document, in whole or in part, is not permitted. The term, "ExxonMobil" is used for convenience, and may include any one or more of ExxonMobil Chemical Company, Exxon Mobil Corporation, or any affiliates in which they directly or indirectly hold any interest.----------------------------------------------------------------------------------------------------------------------------------------------------- Internal Use OnlyMHC: 0, 0, 0, 0, 0, 0 PPEC: ADGN: 2006067XUS (553320)----------------------------------------------------------------------------------------------------------------------------------------------------- Copyright 2002 Exxon Mobil Corporation, All rights reserved。
(完整版)润滑油安全技术说明书MSDS
润滑油安全技术说明书MSDS第一部分：化学名称化学品中文：润滑油化学品俗名：机油化学品英文：lubricating oil 英文名称：Lube oil第二部分：成分/组成信息有害物成分:无含量：100%第三部分：危险性概述危险性类别：无侵入途径：健康危害：急性吸入，可出现乏力、头晕、头痛、恶心，严重者可引起油脂性肺炎。
慢接触者，暴露部位可发生油性痤疮和接触性皮炎。
可引起神经衰弱综合征，呼吸道和眼刺激症状及慢性油脂性肺炎。
有资料报道，接触石油润滑油类的工人，有致癌的病例报告。
环境危害：燃爆危险：本品可燃，具刺激性。
第四部分：急救措施皮肤接触：脱去污染的衣着，用大量流动清水冲洗。
就医。
眼睛接触：提起眼睑，用流动清水或生理盐水冲洗。
就医。
吸入：迅速脱离现场至空气新鲜处。
保持呼吸道通畅。
如呼吸困难，给输氧。
如呼吸停止，立即进行人工呼吸。
就医。
食入：饮足量温水，催吐。
就医。
第五部分：消防措施危险特性：遇明火、高热可燃。
有害燃烧产物：一氧化碳、二氧化碳。
灭火方法：消防人员须佩戴防毒面具、穿全身消防服，在上风向灭火。
尽可能将容器从火场移至空旷处。
喷水保持火场容器冷却，直至灭火结束。
处在火场中的容器若已变色或从安全泄压装置中产生声音，必须马上撤离。
灭火剂：雾状水、泡沫、干粉、二氧化碳、砂土。
第六部分：泄漏应急处理应急处理：迅速撤离泄漏污染区人员至安全区，并进行隔离，严格限制出入。
切断火源。
建议应急处理人员戴自给正压式呼吸器，穿防毒服。
尽可能切断泄漏源。
防止流入下水道、排洪沟等限制性空间。
小量泄漏：用砂土或其它不燃材料吸附或吸收。
大量泄漏：构筑围堤或挖坑收容。
用泵转移至槽车或专用收集器内，回收或运至废物处理场所处置。
第七部分：操作处置与储存操作注意事项：密闭操作，注意通风。
操作人员必须经过专门培训，严格遵守操作规程。
建议操作人员佩戴自吸过滤式防毒面具（半面罩），戴化学安全防护眼镜，穿防毒物渗透工作服，戴橡胶耐油手套。
润滑油MSDS表
其它：工作后，沐浴更衣。保持良好的卫生习惯。
泄漏处置：疏散泄漏污染区人员至安全区，禁止无关人员进入污染区，切断火源。应急处理人员戴好防毒面具，在确保安全的情况下堵漏。用砂土或其它不燃性吸附剂混合吸收，然后收集运至废物处理场所。也可以在保证安全情况下，就地焚烧。如大量泄漏，利用围堤收容，然后收集、转移、回收或无害处理。
润滑油MSDS表
化学品名称：润滑油
分子量：230 – 500
外观与性状：油状液体，淡黄色至褐色，无气味或略带异味。
成分：脂环烃，烷烃
相对密度：（水=1）<1燃烧性：可燃
闪点(℃)：140自燃温度(℃)：248
危险特性：遇高热、明火或与氧化剂接触，有引起燃烧、二氧化碳
眼睛接触：立即翻开上下眼睑，用流动清水冲洗10分钟或用2%碳酸氢钠溶液冲洗并敷硼酸眼膏。就医。
吸入：迅速脱离现场至空气新鲜处，。保暖并休息。呼吸困难时给输氧。呼吸停止时，立即进行人工呼吸。就医。
食入：误服者立即漱口，饮牛奶或植物油，洗胃并灌肠。就医。
防护措施：
工程控制：密闭操作，注意通风。
呼吸系统防护：一般不需特殊防护，但建议特殊情况下，佩戴防毒面具。
灭火方法：泡沫、二氧化碳、1211灭火剂、砂土
储运注意事项：储存于阴凉、通风间内，远离火种、热源。保持容器密封。防止阳光直射。应与氧化剂分开存放。搬运时要轻装轻卸，防止包装及容器损坏。
侵入途径：吸入、食入
毒性：毒性低微，对皮肤粘膜有刺激作用，某些防锈剂可引起接触性过敏性皮炎。
急救：
皮肤接触：脱去污染的衣着，用肥皂水及清水彻底冲洗。