陶瓷机械产品配件及常用术语英文翻译
外国技术员给的陶瓷专业词汇
外国技术员给的陶瓷专业词汇大家参考参考。
压机press 压力pressure 模具mould 型号model 窑炉kiln辊道窑roller kiln 隧道窑tunnel kiln 长度length 内宽internal width 窑炉喷枪kiln nozzle温差temperature difference ,temperature fluctuation 陶瓷棍棒ceramic roller 施釉线glazing line钟罩淋釉bell glazing 甩釉dise glazing 储胚器compensator 喷雾干燥塔spray dryer 球磨机ball mill功率power 容量capacity 印花机screen printing machine 网版printing screen搅拌器stirrer 筛sieve 烘箱dryer 天平balance 量杯beaker施釉喷枪spray gun (for lab glazing) 混料机mixer 烧成温度firing temperature 烧成周期firing cycle烧成曲线firing curve 上温temperature over the tile 下温temperature under the tile配方formula 粘度viscosity 塑性plasticity 比重specific gravity 密度density湿度humidity 水分moisture 吸水率water absorption气孔率porosity釉浆细度particle size of the glaze slip 流动性fluidity 颗粒配级particle distribution 残余量residue目数mesh 热膨胀系数COE (coefficient of thermal expansion)釉面龟裂测试autoclave test 抗冻测试frost resistance test 弯曲强度bending strength 釉面缺陷glaze defect 针孔pinhole 裂纹crack 釉裂crazing 缩釉crawling气泡air bubble 变形deformation 翘曲warp 素烧biscuit firing 釉烧glost firing化学成分chemical composition 色调tone, tonality 光泽度glossiness 色差color difference预热preheat 干燥温度drying temperature 干燥收缩率drying shrinkage烧成收缩率firing shrinkage 硬度hardness 白度whiteness 软化点soften point融化温度melting temperature 耐磨性abrasion resistance 冷却cooling一次烧成single firing 二次烧成double firing 胚体强度body strength氧化气氛oxidizing atmosphere 还原气氛reducing atmosphere日产量daily output 平方米square meter 高岭土kaoling 球土ball clay瓷土china clay 氧化铝alumina, AL203 长石feldspar 钾化石potassium feldspar 钠长石soda feldspar 硅化石zirconium silicate, ZrSi04 石英silica, Si02 滑石talc白云石dolomite 硅灰石wollastonite 添加剂additive 解凝剂deflocculant烧失量I.L, ignition loss 杂质impurity 熔块frit 色料color胚体粉料body powder 可溶性盐soluble salt 釉glaze 釉浆glaze slip透明熔块/ 釉transparent frit / glaze 乳浊熔块/ 釉opaque frit / glaze 无光熔块/ 釉matted frit / glaze 面釉base glaze 底釉engobe 保护釉overglaze 砖胚tile body生胚green body 研磨球grinding ball 柴油diesel gas 液化气LPG天然气natural gas 釉面砖glazed tile 玻化砖porcelain tile 抛光砖polished tile 地砖floor tile墙砖wall tile 内墙砖interior wall tile 外墙砖exterior wall tile 仿古砖rustic tile腰线listel 白胚砖white body tile 红胚砖red body tile 陶瓦roof tile卫生陶瓷sanitary ware 日用陶瓷table ware 艺术陶瓷artistic ware 精细陶瓷fine ceramics陶器pottery 炻器stone ware 瓷器porcelain。
陶瓷术语中英文对照
陶瓷术语中英文对照白云土 dolomite长石feldspar瓷泥petunse, petuntse, petuntze瓷漆enamel paint, enamel封泥lute高岭土kaolin, china clay硅石,二氧化硅silica, SiO2堇青石cordierite莫来石,泥果,石灰,氧化锡釉原材料云母皂石,其它斑点半透明不渗透的不透明的茶叶罐单色的镀金多色的高白工艺品建白材料景德镇景泰蓝cloisonné绝缘子 insulator考古学 archaeology可塑的 plastic流变学 rheology琉璃瓦 glazed tile 模型、模特 model模子 mould耐热 heat-proof配方 formula盆栽 bonsai漆器 lacquer work器皿 ware秦始皇陵兵马俑 life-size terra-cotta soldiers and horses in Chin tomb青铜器 bronze work人类学 antropology渗透的 porous手印，指印 finger mark首饰盒 jewel case丝网印刷 silk screen printing四面体陶瓷的陶工瓦 tile卫生洁具温度硬度釉工砖何朝宗韦奇伍德陶瓷类型薄胎瓷彩陶器,釉陶 faience陈设瓷,摆设瓷 display china瓷 porcelain, china (China ‘中国’来自’Chin’’秦’,在英文中’中国’和’瓷’同一单词)赤陶 terracotta, terracotta, red earthenware代尔夫精陶 delft德化陶瓷 Te-hua porcelain, Dehua pottery高温陶瓷 refractory china工业陶瓷 industrial ceramics工艺瓷,美瓷,艺术瓷 art porcelain, art and craft china, art pottery, artistic china 骨瓷 bone china 官瓷 mandarin porcelain光瓷 lusterware黑色陶器 basalt裂变瓷 crackled porcelain裂纹瓷 crazed china米色陶器 creamware青瓷 celadon青花瓷 bule and white porcelain日用瓷软瓷杀菌陶瓷绳纹陶器施釉陶器炻瓷素彩瓷陶陶瓷锡釉陶细瓷硬瓷紫砂工艺技术凹雕标记玻璃化车削成型 forming冲压,冲压花 repousse瓷土加工 clay processing雕刻 carving浮雕 relief隔焰窑 muffle工艺技术 technology硅氧键 silicon-oxygen bond技艺 technique, craft间断窑 intermittent kiln浇铸 casting拉毛 sgraffito连续窑 continuous kiln镂雕、镂空 piercing辘轳车 jigger泥釉彩饰法 trailing碾磨 grinding抛光 burnishing, polishing破裂 chip嵌入切刻筛子烧制陶瓷科技陶轮细裂纹性能压印窑印花釉上彩釉下彩预加工转模片转印装饰 dé半抛光：纯色的（釉面砖)： monocolor（多用于形容纯色、单色的瓷片和抛光砖）, uniform color, minimalistic color腰线：BORDER，又可以叫LISTELLO；花片：MOTIF，或者是DECORATION PIECE；梯级砖：STEP TILE陶瓷卫生洁具：连体座便器 ONE PIECE TOILET分体座便器 TWO PIECE TOILET挂墙式座便器 WALL HUNG TOILET小便器 URINAL洗手盆柱盆挂盆去水器妇洗器水箱水箱盖盖板水件卫浴洁具：浴缸 BATH TUB按摩缸 WHIRLPOOL蒸汽房 STEAM ROOM淋浴房 SHOWER ROOM, SHOWER CUBICLE淋浴柱 SHOWER PANEL水龙头配件 FAUCET/CP FITTING 冷热水 MIXER冲水阀 FLUSHING VALVE花洒 SHOWER HEAD软管 HOSE菜盆底座水箱盖浴缸裙板浴缸扶手淋浴房地拖池微粉：渗花：瓷质砖：玻化是通体是Full body微粉砖:double loading tiles 渗花砖:marble design瓷质砖:porcelain玻化砖:polished tiles;梯级砖:stairs腰线:border/wall decorative tiles抛光砖 Polished tile釉面砖 Glaze tile仿古砖 Rustic tile耐磨砖：porcelain tile OR unpolished tile卫生陶瓷便器 wc分。
机电设备工业器材常用英语词汇陶瓷ceramics
机电设备、工业器材常用英语词汇陶瓷ceramics合成纤维synthetic fibre电化学腐蚀electrochemical corrosion车架automotive chassis悬架suspension转向器redirector变速器speed changer板料冲压sheet metal parts孔加工spot facing machining车间workshop工程技术人员engineer气动夹紧pneuma lock数学模型mathematical model画法几何descriptive geometry机械制图Mechanical drawing投影projection视图view剖视图profile chart标准件standard component零件图part drawing装配图assembly drawing尺寸标注size marking技术要求technical requirements刚度rigidity内力internal force位移displacement截面section疲劳极限fatigue limit断裂fracture塑性变形plastic distortion脆性材料brittleness material刚度准则rigidity criterion垫圈washer垫片spacer直齿圆柱齿轮straight toothed spur gear斜齿圆柱齿轮helical-spur gear直齿锥齿轮straight bevel gear运动简图kinematic sketch齿轮齿条pinion and rack蜗杆蜗轮worm and worm gear虚约束passive constraint曲柄crank摇杆racker凸轮cams共轭曲线conjugate curve范成法generation method定义域definitional domain值域range导数\\微分differential coefficient求导derivation定积分definite integral不定积分indefinite integral游标卡尺slide caliper千分尺micrometer calipers攻丝tap二阶行列式second order determinant逆矩阵inverse matrix线性方程组linear equations概率probability随机变量random variable排列组合permutation and combination气体状态方程equation of state of gas动能kinetic energy势能potential energy机械能守恒conservation of mechanical energy动量momentum桁架truss轴线axes余子式cofactor逻辑电路logic circuit触发器flip-flop脉冲波形pulse shape数模digital analogy液压传动机构fluid drive mechanism机械零件mechanical parts淬火冷却quench淬火hardening回火tempering调质hardening and tempering磨粒abrasive grain结合剂bonding agent砂轮grinding wheel后角clearance angle龙门刨削planing主轴spindle主轴箱headstock卡盘chuck加工中心machining center车刀lathe tool车床lathe钻削镗削bore车削turning磨床grinder基准benchmark钳工locksmith锻forge压模stamping焊weld拉床broaching machine拉孔broaching装配assembling铸造found液压hydraulic pressure切线tangent机电一体化mechanotronics mechanical-electrical integration 气压air pressure pneumatic pressure稳定性stability介质medium液压驱动泵fluid clutch液压泵hydraulic pump阀门valve失效invalidation强度intensity载荷load应力stress安全系数safty factor可靠性reliability螺纹thread螺旋helix键spline销pin滚动轴承rolling bearing滑动轴承sliding bearing弹簧spring制动器arrester brake十字结联轴节crosshead联轴器coupling链chain皮带strap精加工finish machining粗加工rough machining变速箱体gearbox casing腐蚀rust氧化oxidation磨损wear耐用度durability随机信号random signal离散信号discrete signal超声传感器ultrasonic sensor集成电路integrate circuit挡板orifice plate残余应力residual stress套筒sleeve扭力torsion冷加工cold machining电动机electromotor汽缸cylinder过盈配合interference fit热加工hotwork摄像头CCD camera倒角rounding chamfer优化设计optimal design工业造型设计industrial moulding design有限元finite element伺服电机actuating motor铣床milling machine钻床drill machine镗床boring machine步进电机stepper motor丝杠screw rod导轨lead rail组件subassembly可编程序逻辑控制器Programmable Logic Controller PLC 电火花加工electric spark machining电火花线切割加工electrical discharge wire - cutting相图phase diagram热处理heat treatment固态相变solid state phase changes有色金属nonferrous metal陶瓷ceramics合成纤维synthetic fibre电化学腐蚀electrochemical corrosion车架automotive chassis悬架suspension转向器redirector变速器speed changer板料冲压sheet metal parts孔加工spot facing machining车间workshop工程技术人员engineer气动夹紧pneuma lock数学模型mathematical model画法几何descriptive geometry机械制图Mechanical drawing投影projection视图view剖视图profile chart标准件standard component零件图part drawing装配图assembly drawing尺寸标注size marking技术要求technical requirements刚度rigidity内力internal force位移displacement截面section疲劳极限fatigue limit断裂fracture塑性变形plastic distortion脆性材料brittleness material刚度准则rigidity criterion垫圈washer垫片spacer直齿圆柱齿轮straight toothed spur gear斜齿圆柱齿轮helical-spur gear直齿锥齿轮straight bevel gear蜗杆蜗轮worm and worm gear虚约束passive constraint曲柄crank摇杆racker凸轮cams共轭曲线conjugate curve范成法generation method定义域definitional domain值域range导数\\微分differential coefficient求导derivation定积分definite integral不定积分indefinite integral曲率curvature偏微分partial differential毛坯rough游标卡尺slide caliper千分尺micrometer calipers攻丝tap二阶行列式second order determinant逆矩阵inverse matrix线性方程组linear equations概率probability随机变量random variable排列组合permutation and combination气体状态方程equation of state of gas动能kinetic energy势能potential energy机械能守恒conservation of mechanical energy动量momentum桁架truss轴线axes余子式cofactor逻辑电路logic circuit触发器flip-flop脉冲波形pulse shape数模digital analogy液压传动机构fluid drive mechanism机械零件mechanical parts淬火冷却quench淬火hardening回火tempering调质hardening and tempering磨粒abrasive grain结合剂bonding agent砂轮grinding wheelAssembly line 组装线Layout 布置图Conveyer 流水线物料板Rivet table 拉钉机Rivet gun 拉钉枪Screw driver 起子fit together 组装在一起fasten 锁紧(螺丝)fixture 夹具(治具)pallet 栈板barcode 条码barcode scanner 条码扫描器fuse together 熔合fuse machine热熔机repair修理operator作业员QC品管supervisor 课长ME 制造工程师MT 制造生技cosmetic inspect 外观检查inner parts inspect 内部检查thumb screw 大头螺丝lbs. inch 镑、英寸EMI gasket 导电条front plate 前板rear plate 后板chassis 基座bezel panel 面板power button 电源按键reset button 重置键Hi-pot test of SPS 高源高压测试Voltage switch of SPS 电源电压接拉键sheet metal parts 冲件plastic parts 塑胶件SOP 制造作业程序material check list 物料检查表work cell 工作间trolley 台车carton 纸箱sub-line 支线left fork 叉车personnel resource department 人力资源部production department生产部门planning department企划部QC Section品管科stamping factory冲压厂painting factory烤漆厂molding factory成型厂common equipment常用设备uncoiler and straightener整平机punching machine 冲床robot机械手hydraulic machine油压机lathe车床planer |plein|刨床miller铣床grinder磨床staker=reviting machine铆合机position职务president董事长general manager总经理special assistant manager特助factory director厂长department director部长deputy manager | =vice manager副理section supervisor课长deputy section supervisor =vice section superisor副课长group leader/supervisor组长line supervisor线长assistant manager助理to move, to carry, to handle搬运be put in storage入库pack packing包装to apply oil擦油to file burr 锉毛刺final inspection终检to connect material接料to reverse material 翻料wet station沾湿台Tiana天那水cleaning cloth抹布to load material上料to unload material卸料to return material/stock to退料scraped |\\'skr?pid|报废scrape ..v.刮;削deficient purchase来料不良manufacture procedure制程deficient manufacturing procedure制程不良oxidation |\\' ksi\\'dei?n|氧化scratch刮伤dents压痕defective upsiding down抽芽不良defective to staking铆合不良embedded lump镶块feeding is not in place送料不到位stamping-missing漏冲production capacity生产力education and training教育与训练proposal improvement提案改善spare parts=buffer备件forklift叉车trailer=long vehicle拖板车compound die合模die locker锁模器pressure plate=plate pinch压板bolt螺栓administration/general affairs dept总务部automatic screwdriver电动启子defective product label不良标签identifying sheet list标示单location地点present members出席人员subject主题conclusion结论decision items决议事项responsible department负责单位pre-fixed finishing date预定完成日approved by / checked by / prepared by核准/审核/承办PCE assembly production schedule sheet PCE组装厂生产排配表model机锺work order工令revision版次remark备注production control confirmation生产确认checked by初审approved by核准department部门stock age analysis sheet 库存货龄分析表on-hand inventory现有库存available material良品可使用obsolete material良品已呆滞to be inspected or reworked 待验或重工total合计cause description原因说明part number/ P/N 料号type形态item/group/class类别quality品质prepared by制表notes说明year-end physical inventory difference analysis sheet 年终盘点差异分析表physical inventory盘点数量physical count quantity帐面数量difference quantity差异量cause analysis原因分析raw materials原料materials物料finished product成品semi-finished product半成品packing materials包材good product/accepted goods/ accepted parts/good parts良品defective product/non-good parts不良品disposed goods处理品warehouse/hub仓库on way location在途仓oversea location海外仓spare parts physical inventory list备品盘点清单spare molds location模具备品仓skid/pallet栈板tox machine自铆机tolerance工差score=groove压线cam block滑块pilot导正筒trim剪外边pierce剪内边drag form压锻差pocket for the punch head挂钩槽slug hole废料孔feature die公母模expansion dwg展开图radius半径shim(wedge)楔子torch-flame cut火焰切割set screw止付螺丝form block折刀stop pin定位销round pierce punch=die button圆冲子shape punch=die insert异形子stock locater block定位块under cut=scrap chopper清角active plate活动板baffle plate挡块cover plate盖板male die公模female die母模groove punch压线冲子air-cushion eject-rod气垫顶杆spring-box eject-plate弹簧箱顶板bushing block衬套insert 入块club car高尔夫球车capability能力parameter参数factor系数phosphate皮膜化成viscosity涂料粘度alkalidipping脱脂main manifold主集流脉bezel斜视规blanking穿落模dejecting顶固模demagnetization去磁;消磁high-speed transmission高速传递heat dissipation热传rack上料degrease脱脂rinse水洗alkaline etch龄咬desmut剥黑膜D.I. rinse纯水次Chromate铬酸处理part number/P/N料号good products良品scraped products报放心品defective products不良品finished products成品disposed products处理品barcode条码flow chart流程表单assembly组装stamping冲压molding成型spare parts=buffer备品coordinate座标dismantle the die折模auxiliary fuction辅助功能poly-line多义线heater band 加热片thermocouple热电偶sand blasting喷沙grit 砂砾derusting machine除锈机degate打浇口dryer烘干机induction感应induction light感应光response=reaction=interaction感应ram连杆edge finder巡边器concave凸convex凹short射料不足nick缺口speck瑕??shine亮班splay 银纹gas mark焦痕delamination起鳞cold slug冷块blush 导色gouge沟槽;凿槽satin texture段面咬花witness line证示线patent专利grit沙砾granule=peuet=grain细粒grit maker抽粒机cushion缓冲magnalium镁铝合金magnesium镁金metal plate钣金lathe车mill锉plane刨blinster气泡fillet镶;嵌边through-hole form通孔形式voller pin formality滚针形式cam driver铡楔shank摸柄crank shaft曲柄轴augular offset角度偏差velocity速度production tempo生产进度现状torque扭矩spline=the multiple keys花键quenching淬火tempering回火annealing退火carbonization碳化tungsten high speed steel钨高速的moly high speed steel钼高速的organic solvent有机溶剂bracket小磁导liaison联络单volatile挥发性resistance电阻ion离子titrator滴定仪beacon警示灯coolant冷却液crusher破碎机阿基米德蜗杆Archimedes worm安全系数safety factor; factor of safety安全载荷safe load凹面、凹度concavity扳手wrench板簧flat leaf spring半圆键woodruff key变形deformation摆杆oscillating bar摆动从动件oscillating follower摆动从动件凸轮机构cam with oscillating follower 摆动导杆机构oscillating guide-bar mechanism摆线齿轮cycloidal gear摆线齿形cycloidal tooth profile摆线运动规律cycloidal motion摆线针轮cycloidal-pin wheel包角angle of contact保持架cage背对背安装back-to-back arrangement背锥back cone ；normal cone背锥角back angle背锥距back cone distance比例尺scale比热容specific heat capacity闭式链closed kinematic chain变频器frequency converters变频调速frequency control of motor speed变速speed change变速齿轮change gear change wheel变位齿轮modified gear变位系数modification coefficient标准齿轮standard gear标准直齿轮standard spur gear表面质量系数superficial mass factor表面传热系数surface coefficient of heat transfer表面粗糙度surface roughness并联式组合combination in parallel并联机构parallel mechanism并联组合机构parallel combined mechanism并行工程concurrent engineering并行设计concurred design, CD不平衡相位phase angle of unbalance不平衡imbalance (or unbalance)不平衡量amount of unbalance不完全齿轮机构intermittent gearing波发生器wave generator波数number of waves补偿compensation参数化设计parameterization design, PD残余应力residual stress操纵及控制装置operation control device槽轮Geneva wheel槽轮机构Geneva mechanism ；Maltese cross槽数Geneva numerate槽凸轮groove cam侧隙backlash差动轮系differential gear train差动螺旋机构differential screw mechanism差速器differential常用机构conventional mechanism; mechanism in common use车床lathe承载量系数bearing capacity factor承载能力bearing capacity成对安装paired mounting尺寸系列dimension series齿槽tooth space齿槽宽spacewidth齿侧间隙backlash齿顶高addendum齿顶圆addendum circle齿根高dedendum齿根圆dedendum circle齿厚tooth thickness齿距circular pitch齿宽face width齿廓tooth profile齿廓曲线tooth curve齿轮gear齿轮齿条机构pinion and rack齿轮插刀pinion cutter; pinion-shaped shaper cutter齿轮滚刀hob ,hobbing cutter齿轮机构gear齿轮轮坯blank齿轮传动系pinion unit齿轮联轴器gear coupling齿条传动rack gear齿数tooth number齿数比gear ratio齿条rack齿条插刀rack cutter; rack-shaped shaper cutter齿形链、无声链silent chain齿形系数form factor齿式棘轮机构tooth ratchet mechanism插齿机gear shaper重合点coincident points重合度contact ratio冲床punch传动比transmission ratio, speed ratio传动装置gearing; transmission gear传动系统driven system传动角transmission angle传动轴transmission shaft串联式组合combination in series串联式组合机构series combined mechanism串级调速cascade speed control创新innovation creation创新设计creation design垂直载荷、法向载荷normal load唇形橡胶密封lip rubber seal磁流体轴承magnetic fluid bearing从动带轮driven pulley从动件driven link, follower从动件平底宽度width of flat-face从动件停歇follower dwell从动件运动规律follower motion从动轮driven gear粗线bold line粗牙螺纹coarse thread大齿轮gear wheel打包机packer打滑slipping带传动belt driving带轮belt pulley带式制动器band brake单列轴承single row bearing单向推力轴承single-direction thrust bearing单万向联轴节single universal joint单位矢量unit vector当量齿轮equivalent spur gear; virtual gear当量齿数equivalent teeth number; virtual number of teeth 当量摩擦系数equivalent coefficient of friction当量载荷equivalent load导热性conduction of heat导程lead导程角lead angle等加等减速运动规律parabolic motion; constant acceleration and deceleration motion 等速运动规律uniform motion; constant velocity motion等径凸轮conjugate yoke radial cam等宽凸轮constant-breadth cam等效构件equivalent link等效力equivalent force等效力矩equivalent moment of force等效量equivalent等效质量equivalent mass等效转动惯量equivalent moment of inertia等效动力学模型dynamically equivalent model底座chassis低副lower pair点划线chain dotted line（疲劳）点蚀pitting垫圈gasket垫片密封gasket seal碟形弹簧belleville spring顶隙bottom clearance定轴轮系ordinary gear train; gear train with fixed axes动力学dynamics动密封kinematical seal动能dynamic energy动力粘度dynamic viscosity动力润滑dynamic lubrication动平衡dynamic balance动平衡机dynamic balancing machine动态特性dynamic characteristics动态分析设计dynamic analysis design动压力dynamic reaction动载荷dynamic load端面transverse plane端面参数transverse parameters端面齿距transverse circular pitch端面齿廓transverse tooth profile端面重合度transverse contact ratio端面模数transverse module端面压力角transverse pressure angle锻造forge对称循环应力symmetry circulating stress对心滚子从动件radial (or in-line ) roller follower对心直动从动件radial (or in-line ) translating follower对心移动从动件radial reciprocating follower对心曲柄滑块机构in-line slider-crank (or crank-slider) mechanism多列轴承multi-row bearing多楔带poly V-belt多项式运动规律polynomial motion多质量转子rotor with several masses惰轮idle gear发生线generating line发生面generating plane法面normal plane法面参数normal parameters法面齿距normal circular pitch法面模数normal module法面压力角normal pressure angle法向齿距normal pitch法向齿廓normal tooth profile法向直廓蜗杆straight sided normal worm法向力normal force反馈式组合feedback combining反向运动学inverse ( or backward) kinematics反转法kinematic inversion反正切Arctan范成法generating cutting仿形法form cutting方案设计、概念设计concept design, CD防振装置shockproof device飞轮flywheel飞轮矩moment of flywheel非标准齿轮nonstandard gear非接触式密封non-contact seal非周期性速度波动aperiodic speed fluctuation非圆齿轮non-circular gear粉末合金powder metallurgy分度线reference line; standard pitch line分度圆reference circle; standard (cutting) pitch circle 分度圆柱导程角lead angle at reference cylinder分度圆柱螺旋角helix angle at reference cylinder分母denominator分子numerator分度圆锥reference cone; standard pitch cone分析法analytical method封闭差动轮系planetary differential复合铰链compound hinge复合式组合compound combining复合轮系compound (or combined) gear train复合平带compound flat belt复合应力combined stress复式螺旋机构Compound screw mechanism复杂机构complex mechanism杆组Assur group干涉interference刚度系数stiffness coefficient刚轮rigid circular spline钢丝软轴wire soft shaft刚体导引机构body guidance mechanism刚性冲击rigid impulse (shock)刚性转子rigid rotor刚性轴承rigid bearing刚性联轴器rigid coupling高速带high speed belt高副higher pair格拉晓夫定理Grashoff`s law根切undercutting公称直径nominal diameter高度系列height series功work工况系数application factor工艺设计technological design工作循环图working cycle diagram工作机构operation mechanism工作载荷external loads工作空间working space工作应力working stress工作阻力effective resistance工作阻力矩effective resistance moment公法线common normal line公共约束general constraint公制齿轮metric gears功率power功能分析设计function analyses design共轭齿廓conjugate profiles共轭凸轮conjugate cam构件link鼓风机blower固定构件fixed link; frame固体润滑剂solid lubricant关节型操作器jointed manipulator惯性力inertia force惯性力矩moment of inertia ,shaking moment 惯性力平衡balance of shaking force 惯性力完全平衡full balance of shaking force 惯性力部分平衡partial balance of shaking force 惯性主矩resultant moment of inertia惯性主失resultant vector of inertia冠轮crown gear广义机构generation mechanism广义坐标generalized coordinate轨迹生成path generation轨迹发生器path generator滚刀hob滚道raceway滚动体rolling element滚动轴承rolling bearing滚动轴承代号rolling bearing identification code滚针needle roller滚针轴承needle roller bearing滚子roller滚子轴承roller bearing滚子半径radius of roller滚子从动件roller follower滚子链roller chain滚子链联轴器double roller chain coupling滚珠丝杆ball screw过度切割undercutting函数发生器function generator函数生成function generation含油轴承oil bearing耗油量oil consumption耗油量系数oil consumption factor赫兹公式H. Hertz equation合成弯矩resultant bending moment合力resultant force合力矩resultant moment of force黑箱black box横坐标abscissa互换性齿轮interchangeable gears花键spline滑键、导键feather key滑动轴承sliding bearing滑动率sliding ratio滑块slider环面蜗杆toroid helicoids worm环形弹簧annular spring缓冲装置shocks; shock-absorber灰铸铁grey cast iron回程return回转体平衡balance of rotors混合轮系compound gear train积分integrate机电一体化系统设计mechanical-electrical integration system design机构mechanism机构分析analysis of mechanism机构平衡balance of mechanism机构学mechanism机构运动设计kinematic design of mechanism机构运动简图kinematic sketch of mechanism机构综合synthesis of mechanism机构组成constitution of mechanism机架frame, fixed link机架变换kinematic inversion机器machine机器人robot机器人操作器manipulator机器人学robotics技术过程technique process技术经济评价technical and economic evaluation技术系统technique system机械machinery机械创新设计mechanical creation design, MCD机械系统设计mechanical system design, MSD机械动力分析dynamic analysis of machinery机械动力设计dynamic design of machinery机械动力学dynamics of machinery机械的现代设计modern machine design机械系统mechanical system机械利益mechanical advantage机械平衡balance of machinery机械设计machine design; mechanical design机械特性mechanical behavior机械调速mechanical speed governors机械效率mechanical efficiency机械原理theory of machines and mechanisms机械运转不均匀系数coefficient of speed fluctuation机械无级变速mechanical stepless speed changes基础机构fundamental mechanism基本额定寿命basic rating life基于实例设计case-based design,CBD基圆base circle基圆半径radius of base circle基圆齿距base pitch基圆压力角pressure angle of base circle基圆柱base cylinder基圆锥base cone急回机构quick-return mechanism急回特性quick-return characteristics急回系数advance-to return-time ratio急回运动quick-return motion棘轮ratchet棘轮机构ratchet mechanism棘爪pawl极限位置extreme (or limiting) position极位夹角crank angle between extreme (or limiting) positions 计算机辅助设计computer aided design, CAD计算机辅助制造computer aided manufacturing, CAM计算机集成制造系统computer integrated manufacturing system, CIMS 计算力矩factored moment; calculation moment计算弯矩calculated bending moment加权系数weighting efficient加速度acceleration加速度分析acceleration analysis加速度曲线acceleration diagram尖点pointing; cusp尖底从动件knife-edge follower间隙backlash间歇运动机构intermittent motion mechanism减速比reduction ratio减速齿轮、减速装置reduction gear减速器speed reducer减摩性anti-friction quality渐开螺旋面involute helicoid渐开线involute渐开线齿廓involute profile渐开线齿轮involute gear渐开线发生线generating line of involute渐开线方程involute equation渐开线函数involute function渐开线蜗杆involute worm渐开线压力角pressure angle of involute渐开线花键involute spline简谐运动simple harmonic motion键key交变应力repeated stress交变载荷repeated fluctuating load交叉带传动cross-belt drive交错轴斜齿轮crossed helical gears胶合scoring角加速度angular acceleration角速度angular velocity角速比angular velocity ratio角接触球轴承angular contact ball bearing 角接触推力轴承angular contact thrust bearing角接触向心轴承angular contact radial bearing 角接触轴承angular contact bearing铰链、枢纽hinge校正平面correcting plane接触应力contact stress接触式密封contact seal阶梯轴multi-diameter shaft结构structure结构设计structural design截面section节点pitch point节距circular pitch; pitch of teeth节线pitch line节圆pitch circle节圆齿厚thickness on pitch circle节圆直径pitch diameter节圆锥pitch cone节圆锥角pitch cone angle解析设计analytical design紧边tight-side紧固件fastener径节diametral pitch径向radial direction径向当量动载荷dynamic equivalent radial load径向当量静载荷static equivalent radial load径向基本额定动载荷basic dynamic radial load rating 径向基本额定静载荷basic static radial load tating 径向接触轴承radial contact bearing径向平面radial plane径向游隙radial internal clearance径向载荷radial load径向载荷系数radial load factor径向间隙clearance静力static force静平衡static balance静载荷static load静密封static seal局部自由度passive degree of freedom矩阵matrix矩形螺纹square threaded form锯齿形螺纹buttress thread form矩形牙嵌式离合器square-jaw positive-contact clutch 绝对尺寸系数absolute dimensional factor绝对运动absolute motion均衡装置load balancing mechanism抗压强度compression strength开口传动open-belt drive开式链open kinematic chain开链机构open chain mechanism可靠度degree of reliability可靠性reliability可靠性设计reliability design, RD空气弹簧air spring空间机构spatial mechanism空间连杆机构spatial linkage空间凸轮机构spatial cam空间运动副spatial kinematic pair空间运动链spatial kinematic chain空转idle宽度系列width series框图block diagram雷诺方程Reynolds‘s equatio n离心力centrifugal force离心应力centrifugal stress离合器clutch离心密封centrifugal seal理论廓线pitch curve理论啮合线theoretical line of action隶属度membership力force力多边形force polygon力封闭型凸轮机构force-drive (or force-closed) cam mechanism力矩moment力平衡equilibrium力偶couple力偶矩moment of couple连杆connecting rod, coupler连杆机构linkage连杆曲线coupler-curve连心线line of centers链chain链传动装置chain gearing链轮sprocket sprocket-wheel sprocket gear chain wheel联组V 带tight-up V belt联轴器coupling shaft coupling两维凸轮two-dimensional cam临界转速critical speed六杆机构six-bar linkage龙门刨床double Haas planer轮坯blank轮系gear train螺杆screw螺距thread pitch螺母screw nut螺旋锥齿轮helical bevel gear螺钉screws螺栓bolts螺纹导程lead螺旋传动power screw螺旋密封spiral seal螺纹thread (of a screw)螺旋副helical pair螺旋机构screw mechanism螺旋角helix angle螺旋线helix ,helical line绿色设计green design design for environment马耳他机构Geneva wheel Geneva gear马耳他十字Maltese cross脉动无级变速pulsating stepless speed changes 脉动循环应力fluctuating circulating stress脉动载荷fluctuating load铆钉rivet迷宫密封labyrinth seal密封seal密封带seal belt密封胶seal gum密封元件potted component密封装置sealing arrangement面对面安装face-to-face arrangement面向产品生命周期设计design for product`s life cycle, DPLC 名义应力、公称应力nominal stress模块化设计modular design, MD模块式传动系统modular system模幅箱morphology box模糊集fuzzy set模糊评价fuzzy evaluation模数module摩擦friction摩擦角friction angle摩擦力friction force摩擦学设计tribology design, TD摩擦阻力frictional resistance摩擦力矩friction moment摩擦系数coefficient of friction摩擦圆friction circle磨损abrasion wear; scratching末端执行器end-effector目标函数objective function耐腐蚀性corrosion resistance耐磨性wear resistance挠性机构mechanism with flexible elements挠性转子flexible rotor内齿轮internal gear内齿圈ring gear内力internal force内圈inner ring能量energy能量指示图viscosity逆时针counterclockwise (or anticlockwise)啮出engaging-out啮合engagement, mesh, gearing啮合点contact points啮合线line of action啮合线长度length of line of action啮入engaging-in牛头刨床shaper凝固点freezing point; solidifying point扭转应力torsion stress扭矩moment of torque扭簧helical torsion spring诺模图NomogramO 形密封圈密封O ring seal盘形凸轮disk cam盘形转子disk-like rotor抛物线运动parabolic motion疲劳极限fatigue limit疲劳强度fatigue strength偏置式offset偏( 心) 距offset distance偏心率eccentricity ratio偏心质量eccentric mass偏距圆offset circle偏心盘eccentric偏置滚子从动件offset roller follower 偏置尖底从动件offset knife-edge follower偏置曲柄滑块机构offset slider-crank mechanism拼接matching评价与决策evaluation and decision频率frequency平带flat belt平带传动flat belt driving平底从动件flat-face follower平底宽度face width平分线bisector平均应力average stress平均中径mean screw diameter平均速度average velocity平衡balance平衡机balancing machine平衡品质balancing quality平衡平面correcting plane平衡质量balancing mass平衡重counterweight平衡转速balancing speed平面副planar pair, flat pair平面机构planar mechanism平面运动副planar kinematic pair平面连杆机构planar linkage平面凸轮planar cam平面凸轮机构planar cam mechanism平面轴斜齿轮parallel helical gears普通平键parallel key其他常用机构other mechanism in common use 起动阶段starting period启动力矩starting torque气动机构pneumatic mechanism起始啮合点initial contact , beginning of contact气体轴承gas bearing千斤顶jack嵌入键sunk key强迫振动forced vibration切齿深度depth of cut曲柄crank曲柄存在条件Grashoff`s law曲柄导杆机构crank shaper (guide-bar) mechanism曲柄滑块机构slider-crank (or crank-slider) mechanism 曲柄摇杆机构crank-rocker mechanism曲齿锥齿轮spiral bevel gear曲率curvature曲率半径radius of curvature曲面从动件curved-shoe follower曲线拼接curve matching曲线运动curvilinear motion曲轴crank shaft驱动力driving force驱动力矩driving moment (torque)全齿高whole depth权重集weight sets球ball球面滚子convex roller球轴承ball bearing球面副spheric pair球面渐开线spherical involute球面运动spherical motion球销副sphere-pin pair球坐标操作器polar coordinate manipulator燃点spontaneous ignition热平衡heat balance; thermal equilibrium人字齿轮herringbone gear冗余自由度redundant degree of freedom柔轮flexspline柔性冲击flexible impulse; soft shock柔性制造系统flexible manufacturing system; FMS柔性自动化flexible automation润滑油膜lubricant film润滑装置lubrication device润滑lubrication润滑剂lubricant三角形花键serration spline三角形螺纹V thread screw三维凸轮three-dimensional cam三心定理Kennedy`s theorem砂轮越程槽grinding wheel groove砂漏hour-glass少齿差行星传动planetary drive with small teeth difference 设计方法学design methodology设计变量design variable设计约束design constraints深沟球轴承deep groove ball bearing生产阻力productive resistance。
陶瓷设备名称英汉对照表
ISO Documents ISO Records nonconformity quality assurance quality control quality management sytem quality management quality policy technical training work instruction ball mill clearances ball mill liners ball mill BIN#10 blender body preparation section bucket elevator burner Clear water pump continous ball mill conveyor belt conveyor spares diaphram pumps electro magnet empty containey forklift garbage
陶瓷行业机器设备专用词语对照表
设备：釉线 设备：釉线 设备：釉线 设备：釉线 设备：釉线 设备：釉线 设备：釉线 设备：釉线 设备：釉线 设备：釉线 设备：釉线 设备：釉线 设备：釉线 设备：窑炉 设备：窑炉 设备：窑炉 设备：窑炉 设备：窑炉 设备：窑炉 设备：窑炉 设备：窑炉 设备：窑炉 设备圆盘式甩釉机 釉线 辊筒印花机 双蜂碟式甩釉柜 平面（丝网）矩型式印花机 印花的刮刀 砖坯干燥机 立式干燥器 上坯底水 喷水柜 冷却风机 助燃风机 煤气炉 卧式干燥器 抽热风机 抽热风机 窑炉 陶瓷棍棒 液化石油气 排烟风机 急冷风机 辊道窑 compensator compenser Deco printing Disc glazing line rotomatrix printing machine double disc flat matrix printing scraper tile drier vertical dryer wash coat water spray Booth cold air fan combustion air fan Gas stove Horizontal dryer Hot air R.I.F.fan Hot air fan kiln kiln ceramic rollers Liquified petroleum gas Smoke air fan specd cold air roller kiln 设备：窑炉 设备：窑炉 设备：压机 设备：压机 设备：压机 设备：压机 设备：压机 设备：压机 设备：压机 设备：压机 设备：压机 设备：压机 设备：压机 设备：压机 设备：压机 设备：压机 设备：压机 设备：抛光 设备：抛光 设备：抛光 设备：抛光 设备：抛光 设备：抛光 磨棒机 砖出窑的 吸砖机 两次布料 推粉架 润滑油 模具的侧板 下模冲头 机修车间 杂物 模具 压机（压机记录表） 冲压 模芯 备用模具 备用模芯 各种润滑油 上模冲头（模芯） 磨块 倒角机 精磨单元 刮平机 锯砖机 艺术砖抛光机 rollercleaning machine sucker machine doublc filling floating grid lubricant oils liner lower punches Mechanical workshop miscellaneous items mould press /press log book pressing punche spare mould spare punches Lubricant for various machines Uper punches Abrasive beveling machine Brushing unit calibrating machine cutting machine décor polishing machine
陶瓷生产中英文对照常用设备全解
陶瓷生产中英文对照常用设备全解中英文对照常用设备名称及术语手册CHINESE/ENGLISH HANDBOOK FOR TECHNICIANS 常用安装设备和工具Machines and Tools叉车Forklift磨轮切割机Disc cutting machine液压拖车Hydraulic trolley手动液压叉车Manual hydraulic forklift电焊机Electric Welding Machine氧气乙炔气割Oxygen-acetylene Cutting Device手提打磨机Portable Abrader冲击钻Ground Drill电钻Electric Drill扳手Spanner/Wrench钳子Pliers / Pincers螺丝刀Screwdriver刀Knife手锯Handsaw锤Hammer卷尺Tapeline/Tape Measure水准仪Level台钻Bench drill真空清洁器Vacuum Cleaner配电箱Power Cabinet/Distribution Cabinet电缆Cable插座Socket/Outlet/Distribution Block检测设备和仪器Laboratory Equipments陶瓷砖断裂模数测定仪（抗折仪）Ceramic brick cracking modulus tester(bending strength tester)陶瓷吸水率测定仪Ceramic water absorption tester陶瓷釉面抗釉裂试验仪Ceramic brick cracking modulus tester(bending strength tester)陶瓷砖平整度、边直度直角度综合测定仪Ceramic brick smoothing degree, edge linear degree, right-angled degree, synthesis degree tester陶瓷砖釉面耐磨性能测定仪Ceramic brick encaustic anti-abrasion tester陶瓷砖钢轮深度耐磨仪（无釉砖耐磨仪）Biscuit tile anti-abrasion tester(steel roll mill)陶瓷砖抗热震性检测仪Ceramic brick thermal shock-resistance tester智能透光度测定仪Brain porcelain foetus transmittance tester全自动白度仪Portable whiteness colorimeter材料高温物性仪Material high-temperature physical property tester (high-temperature microscope)卧式高温膨胀仪High-temperature expansion instrument快速研磨机Fast mill滚轮研磨机Roll ball mill电动振筛机Electromotive vibration sieve machine手扳式液压制样机Sampling machine with manual and sap pressure电热鼓风恒温干燥箱Thermostaticand air-circulation oven(Electrically-heated) 高温熔块炉High-temperature fusion cake furnace箱式电阻炉Box resistance furnace快速升温箱式电阻炉Quick-heating box resistance-furnaces箱式梯度炉Gradient resistance furnace水分快速测定仪Moisture quick determination meter硅酸盐化学成份快速测定Chemical composition quick determination meter分析天平Analytical balance托盘天平Table balance生产线设备production Line Equipments原料输送部分Raw Materials Transportation Dept.喂料机（钢料斗及平台）Feeding machine (hopper and platform)皮带输送机Belt conveyor双向皮带输送机Two-Way belt conveyor电动葫芦Electric hoist地中衡Ground balance泥浆制备部分Slip Preparation Dept.球磨机Ball mill泥浆搅拌机Slip stirrer圆形振动筛Vibrating sieve (round)气动隔膜泵Pneumatic diaphragm pump 水表Water meter 粉料制备部分Powder Preparation Dept.柱塞泵Piston pump喷雾干燥塔Spray dryer粉料振动筛Vibrating sieve for powder 大倾角裙边皮带输送机Inclined skirt-sided belt conveyor粉料仓Powder silo料位探针Level probe粉料输送部分Powder Transportation Dept.旋转式下料机Rotating discharger冲压成型部分Pressing Dept.压机粉料仓Hopper for press压机Press翻坯机Take-off table干燥部分Drying/Biscuit firing Dept.横向连接线（包括过渡辊台）Connection line (including transition table)干燥/素烧窑进窑机Dryer/biscuit kiln loading machine干燥窑Dryer干燥/素烧窑出窑机Dryer/biscuit kiln unloading machine施釉部分Glazing Dept.施釉输送线Glazing line90度转弯器900 curve扫尘装置Brush吹尘机Dust fan匀砖器Tile uniformer喷水柜Moisture cabinet双尖蜂施釉柜Double disc cabinet钟罩式淋釉器Bell shape coating unit固釉箱（全套）Fixative cabinet (complete) 小型补偿器Mini-compensator丝网印花机Silk screen printing machine 洗边机Edge cleaner 调边机Turning device底釉机组（全套）Engobe spreading device (complete)圆型不锈钢釉罐（釉桶及立式泵）Stainless steel round tank (with glaze tank and vertical pump) 甩釉座Adaptor甩釉头Disc Spray, Top Spray烧成部分Glost firing Dept.釉烧窑进窑机Gloss kiln loading machine窑前储坯器Pre-kiln Compensator釉烧窑Glost roller kiln釉烧出窑机及传送辊台Glost kiln unloading machine and transport table釉料制备部分Glaze Preparation Dept.球磨机（高铝内衬）Ball mill (including alumina lining)地中衡Ground balance釉料罐搅拌机Glaze stirrer除铁器Iron removing device风机管路系统Piping system排烟风机Exhausting fan助燃风机Combustion air fan急冷风机Rapid cooling fan慢冷风机Heat-exchange fan尾冷风机Final cooling fan尾部抽热风机Final suction cooling fan燃烧系统(Combustion system)火焰探测器Flame sensor减压阀Pressure reducer安全释放阀Safety and relief valve高低压压力开关Switch for max. and min. pressure 压力表Manometer/Pressure meter窑炉，原材料及制品Kiln, raw materials and products辊道窑Roller kiln梭式窑Shuttle kiln遂道窑Tunnel kiln素烧窑，坯窑Biscuit kiln干燥窑Dryer粘土Clay长石Feldspar石英岩Quartz釉料Glaze建筑陶瓷Building Ceramic日用陶瓷Tableware卫生洁具Sanitaryware瓷器Porcelain/China陶器Pottery通体砖Homogenous tile墙砖Wall tile地砖Floor tile渗花砖Soluble salt tile釉面砖Glazed tile微粉砖Micro-powder tile生坯Green tile素烧Biscuit firing素瓷Biscuit porcelain二次布料微粉砖Double charge micro-powder tile 釉烧Glost firing内墙砖Internal wall tile外墙砖External wall tile配套设备，备件,材料及其它Spare Parts，materials and others摆线针轮减速器Cycloid reduction motor三相异步电机3-phase asynchronous motor 窑炉喷枪/烧嘴Burner制粒机Granulator破碎机 Crusher摇动筛Swing sieve变量柱塞泵Variable piston pump蜗轮减速器Wormgear reducer无级变速器Stepless variator倒角总成Chamfering unit标准筛Standard sieve磅秤Platform scale恒温干燥箱Thermostatic oven喂料机Feeding Machine可逆可转皮带机Reversible & removable belt conveyor 洗边机Scraper group/Edge cleaner补偿器Compensator平浆搅拌机Blade stirrer方形振动筛Quadrate vibrating sieve流槽式除铁器Trough iron removing气动隔膜泵Pneumatic diaphragm pump电控柜Control panel货物提升机Goods lift一次布料车Single charger液压压砖机Hydraulic press带式印花机Belt printing machine筛式印花机Screen printing machine瓷辊修磨机Roller grinding machine污水处理系统Sewage system自动加釉装置Automatic glaze-feeding device 刮平定厚机Calibrating machine粗磨机Rough grinding machine云彩喷雾机Spray gun booth定色机Fixative booth压滤机Filter press釉泵Glaze pump喷水柜Moisture booth底浆机Engobe machine分坯机Tile-regulating device烧咀砖Burner brick孔砖Roller passage brick挡火板Baffle plate纤维Fiber高铝High aluminum观火孔棉塞View hole plug吊顶砖Ceiling block高铝棉毯 High aluminum f iber blanket 标砖Refractory brick 高温粘接剂Refractory cement/adhesive陶瓷纸Ceramic fiber paper普通板Refractory slab单孔总成Gear with aluminum block assembly (single-gear) 从动端轴承Bearing for idle side带座轴承Bearing with house钢丝套Steel wire spring弹簧片Spring clip瓷棒Ceramic roller斜齿轮Helical gear短管接头Nipple手动球阀Manual Ball valve铝波纹管Aluminum corrugated pipe喉箍Clip风机轴承Bearing for fan传动皮带Driving belt交流接触器AC contactor辅助触头组Auxiliary contact热继电器Thermal relay断路器Breaker中间继电器Relay时间继电器Time relay温控表Thermal regulator热电偶Thermocouple发光二极管Light-emitting diode空气开关Air switch保险座 Fuse holder执行器 Actuator报警器 Alarm/siren同步齿形带Synchronizing toothed belt 三角皮带Triangular belt滑杆 Sliding bar同步带轮 Synchronizing pulley塑料辊棒支座 Plastic roller steadier辊棒轴 Roller shaft15齿固定链轮 Fixed chain wheel with 15 teeth 轴承座 Bearing house窄形切角轴承 Machine bearing with house 密封石棉垫 Sealed asbestos pad轴承芯 Bearing core齿链轮 T oothed chain wheel螺丝钉 Screw螺杆 bolt螺帽 Nut磨块 Abrasives液化器 Liquefier气缸 Air cylinder单向结流阀 Return orifice check valve 套筒 Sleeve for bearing 滑动轴承 Sliding bearing套阀，圆柱滑阀 Sleeve valve从动/主动齿轮 Idle/Driving Gear“O”型密封垫“O”type seal橡胶垫 Rubber pad减振垫 Cushion block隔套 Spacer sleeve钢管 Steal tubeC型钢 C type steal摆杆轴Shaft of swing rod铜料斗Brass hopper槽，走线架 Cable tray擦底边机 Tile bottom edge fettling group 销轴承 Pin bearing 针阀 Pin valve堕轮 Idle wheel机械传动 Mechanical drive喷雾嘴Atomizer nozzle喷雾器 A tomizer二通插装阀2-way cartridge valve三角（皮）带Cone belt/triangular belt/V belt过滤器Filter磨边倒角Squaring and chamfering柱塞缸Plunger cylinder曲柄Crank电气元件Electric component锁模Die-lock/mould locker阀组Valve group冷却管Tube cooler管芯Tube core复合顶出装置Compound ejecting device 滤管Tube funnel 行星模头Planetary head紧固件Fastening part打蜡盘Waxing plate同步齿形带Timing belt斜齿轮Helical gear磁控柜Magnetic control cabinet 球石Milling ball进料平台Feeding platform定量给水器Water rationing device磅秤Platform scale进料斗Feeding hopper泥浆伺服罐Slip service tank浆池Slip tank热风炉Hot air generator中转罐Transit tank料仓Silo电子皮带秤Electronic belt scale干法除铁Dry iron-removing下料管Powder tube上磁吸板Upper magnetic plate承接辊台Roller connector横向连接线Cross connecting line砖坯输送线Conveying line吹尘器Dust fan温度指示仪T emperature indicator除尘器Dust collector圆釉桶Round glaze tank釉线过桥Bridge over glazing line滤尘器Dust filter浆池Slip tank额定电压Nominal voltage电源频率Frequency输浆管路Slip transport pipe液晶显示屏Liquid crystal display/LED 液化天然气LNG(liquified natural gas) 液化石油气LPG(liquified petroleum gas) 程序逻辑控制系统PLCProgram logic control system大规模集成液压系统Large-scale integrated hydraulic system抛痕Polishing mark/trace填料深度Soft clay max filling冲压频率Pressing frequency立柱间距Distance between columns 最大冲程Max plunger stroke主电机功率Main motor power装模空间Space of mould比例伺服控制Proportion service control金刚石辊子Diamond roller整体铸架Integrated casting structure三相四线3-phase & 4－wire双链印花Double-chain printing泥浆陈腐Slip ageing压缩空气Compressed air底釉Engobe面釉Overglaze回抛率Re-polishing rate合格率Conformity rate烧失量Firing loss粒度Granularity球磨时间Milling time料，球石，水比例Proportion of raw material, ball and water球磨细度milling precision泥浆含水率slip moisture泥浆粘度slip viscosity泥浆陈腐时间slip aging time塔顶温度temperature on top spray dryer 热风炉温度temperature of hot air generator 塔内负压minus pressure in spray dryer 粉料含水率powder moisture排风温度temperature of exhausting色料仓color silo粉料陈腐时间powder aging time洗塔washing tower压机循环次数working cycle of press压机液压油温度temperature of hydraulic oil 生坯强度strength of green tile毛边rough edges起泡bubble干燥周期drying cycle干燥温度曲线drying temperature curve 最高干燥温度max. drying temperature干燥能耗（kcal/kg H2O）Energy consumption in drying（kcal/kg H2O）干燥缺陷率error rate of drying t进干燥生坯含水率moisture of green tile on loading machine出干燥砖含水率moisture of tile on unloading machine烧成周期firing cycle烧成烧成曲线firing temperature curve最高干燥温度max. firing temperature烧成能耗（kcal/kg产品）Energy consumption of firing（kcal/kg products）烧成收缩率firing shrinkage排烟烟气温度temperature of exhausting smoke助燃风压combustion air pressure急冷温度rapid cooling temperature 出砖温度tile temperature at exit产量（班产，日产）Output (shift, daily)合格率rate of conformity碰角bump angle变形deformation平整度flatness色差chromatism/color defect 尺寸size对角尺寸diagonal deviation吸水率water absorptivity抗折强度bending strength设备描述Equipment Description圆形振动筛φ1000筛网直径：ф1000mm筛网层数: 2（上层50目,下层80目）振动频率: 1400～1500功率: 1.5KW材料（与泥浆接触部分）：1Cr18Ni9TiVibrating sieve?1000Diameter of the sieve ?1000mmLayers of the sieve2 (50 meshes for upper and 80 meshes for lower)。
陶瓷行业术语英文对照
粗瓷 :stoneware白云土 :dolomite红土 :terracotta建白材料 :construction/building material哑光 :matt透明釉 :transparent不透明釉 :opaque色釉 :pigmented裂纹釉 :crackled珍珠釉 :pearlized釉下彩 :under glazed釉上彩:on-glazed浮雕 :relief, emboss素烧:bisque firing釉烧 :glost firing镀金 :gild贴花: decal首饰盒 :trinket box丝网印 :silk screen printing素彩瓷 :plain porcelain高温陶瓷 :refractory china窑:kiln隧道窑: tunnel印花: stamping陶瓷原料 Ceramic Material长石feldspar瓷泥petunse, petuntse, petuntze瓷漆enamel paint, enamel封泥lute高岭土kaolin, china clay硅石,二氧化硅silica, SiO2堇青石cordierite莫来石,红柱石andalusite泥果,坯体clay body泥釉slip石灰,生石灰,氧化钙lime, calcium oxide, CaO 氧化锡tin oxide釉glaze原材料raw material云母mica皂石,块滑石steatite陶瓷类型 Types of Pottery碧玉细炻器 jasper薄胎瓷 thin china彩陶器,釉陶 faience陈设瓷,摆设瓷 display china瓷porcelain, china (China ‘中国’来自’Chin’’秦’,在英文中’中国’和’瓷’同一单词)赤陶 terracotta, terracotta, red earthenware代尔夫精陶 delft德化陶瓷 Te-hua porcelain, Dehua pottery高温陶瓷 refractory china工业陶瓷 industrial ceramics工艺瓷,美术瓷,艺术瓷 art porcelain, art and craft china, art pottery, artistic china骨瓷 bone china官瓷 mandarin porcelain光瓷 lusterware黑色陶器 basalt裂变瓷 crackled porcelain裂纹瓷 crazed china米色陶器 creamware青瓷 celadon青花瓷 bule and white porcelain轻质瓷、轻瓷 light china日用瓷 household china, table ware软瓷 soft porcelain杀菌陶瓷 antiseptic pottery绳纹陶器 Jomon pottery施釉陶器 slipware炻瓷 stoneware素彩瓷 plain porcelain陶 earthenware陶瓷 pottery无釉陶、陶瓷素烧坯 biscuit, unglazed ware锡釉陶 majolica细瓷 fine china硬瓷 hard porcelain赭色粘土陶器 terra sigillata紫砂 purple granulated, purple sand, terra-cotta工艺技术 Technology凹雕 intaglio标记 marking玻璃化 vitrify车削 turning成型 forming冲压,冲压花 repousse瓷土加工 clay processing雕刻 carving浮雕 relief隔焰窑 muffle工艺技术 technology硅氧键 silicon-oxygen bond技艺 technique, craft间断窑 intermittent kiln浇铸 casting拉毛 sgraffito连续窑 continuous kiln镂雕、镂空 piercing辘轳车 jigger泥釉彩饰法 trailing碾磨 grinding抛光 burnishing, polishing破裂 chip嵌入 inlay切刻 incising筛子 sieve烧制 firing陶瓷科技 ceramics陶轮potter’s wheel贴花、嵌花 appliqu, decal凸雕，底切，拉底，底部掏槽 undercut细裂纹 craze性能 property压印 impressing窑 kiln印花 stamping釉上彩 overglazed color figure釉下彩 underglazed color figure预加工 pre-processing粘性，粘滞性 viscosity, stiffness转模片 jiggered piece转印 transfer print装饰 d cor, decoration其它 Others斑点 speck半透明 translucence, translucency, translucent 不渗透的 nonporous不透明的 opaque茶叶罐 caddy单色的 monochrome多色的 polychrome高白 high white, Gaobai工艺品 artware鬼工，鬼爷神工demon’s work, kuei kung景德镇 Jingdexhen, Ching-te-chen景泰蓝 cloisonn绝缘子 insulator考古学 archaeology可塑的 plastic流变学 rheology琉璃瓦 glazed tile模型、模特 model模子 mould耐热 heat-proof配方 formula盆栽 bonsai漆器 lacquer work器皿 ware秦始皇陵兵马俑 life-size terra-cotta soldiers and horses in Chin tomb青铜器 bronze work人类学 antropology渗透的 porous手印，指印 finger mark丝网印刷 silk screen printing四面体 tetrahedral搪瓷，珐琅 enamel陶瓷的 ceramic陶瓷专家，陶瓷艺术家 ceramist陶工 potter瓦 tile碗 bowl卫生洁具 sanitary ware温度 temperature硬度 hardness釉工 glazier圆块，雕球，瘤 knob砖 brick爱比克泰德 Epicteus（活动于520-500 BC）古希腊陶工兼画家何朝宗 He Chaozhong（1522-1620） Chinese ceramist in Ming Dynasty,中国明代陶瓷艺术家韦奇伍德 Wedgwood（1730-1795）英国著名陶瓷工匠和制造商希腊古瓮颂’Ode on a Crecian Urn’英国诗人济慈 Keats（1795-1821）的名诗，惊叹古希腊陶器彩绘之精美耐火材料赛拉棉Cerafiber赛拉含锆棉Cerachem Fiber赛拉含铬棉 Cerachrome Fiber赛拉毯Cerablanket赛拉含锆毯Cerachema Blanket赛拉含铬毯 Cerachromea Blanket马福特克（莫来石）毯 MAFTEC Blanket耐火纤维组件 Refractory Fiber Modules纤维贴面块 Veneering Modules赛拉板 Ceraboard TM背衬板607 Blok 607TM赛拉纸 Cerapaper赛拉毡 Cerafelt轻质隔热砖 Insulating Firebircks JM隔热吊顶砖 Root Blocks BV耐火胶泥 JM2600 Blakite JM3300轻质莫来石绝热砖 Light Insulating Bricks聚轻高铝砖 Poly Light High Aluminum Firebrick高温耐火胶泥High- temperature Refractory Mortar磷酸铝不烧砖系列 Aluminophosphat Bonded Firebricks高温窑具 High-temperature Kiln Furniture堇青石--莫来石窑具 Cordierite-mullite Kiln Furniture轻质耐火浇注料 Low-weight Refractory Castable高温轻质耐火浇注料 High-temp Light Weight Refractory Castable低蠕变高铝砖 Low Creep High Alumina Bricks热风炉用高铝砖 High Alumina Bricks for Hot Blast Stove通用粘土质耐火砖 Fireclay Bricks高炉用粘土质耐火砖 Fireclay Bricks for Blast Furnaces特种耐火泥浆 Special Refractory Mortar轻质隔热耐火砖 Insulating Bricks电炉顶砖 High Alumina Bricks for EAF微膨胀刚玉砖 Dilatable High Alumina Bricks不烧铝镁砖 Unburnt Al2O3-MgO Bricks铝镁尖晶石砖 Alumina-Spinel Bricks刚玉、铬刚玉透气砖 Corundum and Chrome-Corundum Purging Plugs for Ladle Refining 铝－碳化硅－碳砖 Al2O3-SiC-C Bricks锆铬刚玉砖 Zr-Cr-Corundum Brick铬刚玉尖晶石砖 Chrome-Corundum-Spinel Brick铝镁碳砖 Al2O3-MgO-C Bricks铝碳砖 Al2O3-C Bricks通用高铝砖 High Alumina Bricks高炉用高铝砖 High Alumina Bricks for Blast Furnaces高炉出铁沟浇注料 Refractory Castables for BF Troughs and Runners钢包浇注料 Refractory Carstables for Ladles金花米黄、渗花砖、蓝宝石、大颗粒、纯色砖 golden yellow, glazed-lmitated, sapphire of polishing series, big grain and solid color内墙砖 wall tile地砖 floor tile广场砖 paving tile完全玻化砖 polished tile金玉石 polished mosaic精工钻 fine granule陶瓷砖和卫生陶瓷分类及术语陶瓷砖 ceramic tile由粘土或其他无机非金属原料，经成型、烧结等工艺处理，用于装饰与保护建筑物、构筑物墙面及地面的板状或块状陶瓷制品。
(完整版)陶瓷术语中英文对照.doc
精心整理陶瓷术语中英文对照白云土 dolomite长石 feldspar瓷泥 petunse,petuntse,petuntze瓷漆 enamelpaint,enamel封泥 lute高岭土 kaolin,chinaclay硅石 , 二氧化硅 silica,SiO2堇青石 cordierite莫来石 , 红柱石 andalusite泥果 , 坯体 claybody 泥釉 slip石灰 , 生石灰 , 氧化钙 lime,calciumoxide,CaO氧化锡 tinoxide釉 glaze原材料 rawmaterial云母 mica皂石 , 块滑石 steatite其它 Others斑点 speck半透明 translucence,translucency,translucent不渗透的 nonporous不透明的 opaque茶叶罐 caddy单色的 monochrome镀金 gild多色的 polychrome高白 highwhite,Gaobai工艺品 artware鬼工，鬼爷神工demon’swork,kueikung建白材料 construction/buildingmaterial景德镇 Jingdexhen,Ching-te-chen景泰蓝 cloisonn é绝缘子 insulator考古学 archaeology可塑的 plastic流变学 rheology琉璃瓦 glazedtile模型、模特model模子 mould耐热 heat-proof配方 formula盆栽 bonsai漆器 lacquerwork器皿 ware秦始皇陵兵马俑life-sizeterra-cottasoldiersandhorsesinChintomb青铜器 bronzework人类学 antropology渗透的 porous手印，指印 fingermark首饰盒 jewelcase丝网印刷 silkscreenprinting四面体 tetrahedral搪瓷，珐琅 enamel陶瓷的 ceramic陶瓷专家，陶瓷艺术家ceramist陶工 potter瓦 tile 碗 bowl卫生洁具 sanitaryware温度 temperature硬度 hardness釉工 glazier圆块，雕球，瘤knob砖 brick爱比克泰德 Epicteus （活动于 520-500BC）古希腊陶工兼画家何朝宗 HeChaozhong（1522-1620）ChineseceramistinMingDynasty, 中国明代陶瓷艺术家韦奇伍德 Wedgwood（1730-1795）英国著名陶瓷工匠和制造商希腊古瓮颂’ OdeonaCrecianUrn’英国诗人济慈 Keats （ 1795-1821）的名诗，惊叹古希腊陶器彩绘之精美陶瓷类型 TypesofPottery碧玉细炻器 jasper薄胎瓷 thinchina彩陶器 , 釉陶 faience陈设瓷 , 摆设瓷 displaychina瓷 porcelain,china(China ‘中国’来自’ Chin’’秦’ , 在英文中’中国’和’瓷’同一单词 ) 赤陶 terracotta,terracotta,redearthenware代尔夫精陶 delft德化陶瓷 Te-huaporcelain,Dehuapottery高温陶瓷 refractorychina工业陶瓷 industrialceramics工艺瓷,美瓷, 艺术瓷 artporcelain,artandcraftchina,artpottery,artisticchina骨瓷bonechina 官瓷 mandarinporcelain光瓷 lusterware黑色陶器 basalt裂变瓷 crackledporcelain裂纹瓷 crazedchina米色陶器 creamware青瓷 celadon青花瓷 buleandwhiteporcelain轻质瓷、轻瓷 lightchina日用瓷 householdchina,tableware软瓷 softporcelain杀菌陶瓷 antisepticpottery绳纹陶器 Jomonpottery施釉陶器 slipware炻瓷 stoneware素彩瓷 plainporcelain陶 earthenware陶瓷 pottery无釉陶、陶瓷素烧坯biscuit,unglazedware锡釉陶 majolica细瓷 finechina硬瓷 hardporcelain赭色粘土陶器 terrasigillata紫砂 purplegranulated,purplesand,terra-cotta工艺技术 Technology凹雕 intaglio标记 marking玻璃化 vitrify车削 turning成型 forming冲压 , 冲压花 repousse瓷土加工 clayprocessing雕刻 carving浮雕 relief隔焰窑 muffle工艺技术 technology硅氧键 silicon-oxygenbond技艺 technique,craft间断窑 intermittentkiln浇铸 casting拉毛 sgraffito连续窑 continuouskiln镂雕、镂空 piercing辘轳车 jigger泥釉彩饰法 trailing碾磨 grinding抛光 burnishing,polishing破裂 chip嵌入 inlay切刻 incising筛子 sieve烧制 firing陶瓷科技 ceramics陶轮 potter ’swheel贴花、嵌花 appliqu é,decal凸雕，底切，拉底，底部掏槽undercut细裂纹 craze性能 property压印 impressing窑 kiln印花 stamping釉上彩 overglazedcolorfigure釉下彩 underglazedcolorfigure预加工 pre-processing粘性，粘滞性viscosity,stiffness转模片 jiggeredpiece转印 transferprint装饰 décor,decoration半抛光： semi-polish，但意大利人形容半抛不说semi-polish而是用lappato来形容。
陶瓷术语中英文对照
陶瓷术语中英文对照陶瓷术语中英文对照白云土dolomite长石feldspar瓷泥petunse, petuntse, petuntze瓷漆enamel paint, enamel封泥lute高岭土kaolin, china clay硅石,二氧化硅silica, SiO2堇青石cordierite莫来石,红柱石andalusite泥果,坯体clay body 泥釉slip石灰,生石灰,氧化钙lime, calcium oxide, CaO 氧化锡tin oxide釉glaze原材料raw material云母mica皂石,块滑石steatite其它Others斑点speck半透明translucence, translucency, translucent 不渗透的nonporous不透明的opaque茶叶罐caddy单色的monochrome镀金gild多色的polychrome高白high white, Gaobai工艺品artware鬼工，鬼爷神工demon’s work, kuei kung建白材料construction/building material景德镇Jingdexhen, Ching-te-chen景泰蓝cloisonné绝缘子insulator考古学archaeology可塑的plastic流变学rheology琉璃瓦glazed tile 模型、模特model模子mould耐热heat-proof配方formula盆栽bonsai漆器lacquer work器皿ware秦始皇陵兵马俑life-size terra-cotta soldiers and horses in Chin tomb青铜器bronze work人类学antropology渗透的porous手印，指印finger mark首饰盒jewel case丝网印刷silk screen printing四面体tetrahedral搪瓷，珐琅enamel陶瓷的ceramic陶瓷专家，陶瓷艺术家ceramist陶工potter瓦tile 碗bowl卫生洁具sanitary ware温度temperature硬度hardness釉工glazier圆块，雕球，瘤knob砖brick爱比克泰德Epicteus（活动于520-500 BC）古希腊陶工兼画家何朝宗He Chaozhong（1522-1620）Chinese ceramist in Ming Dynasty,中国明代陶瓷艺术家韦奇伍德Wedgwood（1730-1795）英国著名陶瓷工匠和制造商希腊古瓮颂’Ode on a Crecian Urn’英国诗人济慈Keats （1795-1821）的名诗，惊叹古希腊陶器彩绘之精美陶瓷类型Types of Pottery碧玉细炻器jasper薄胎瓷thin china彩陶器,釉陶faience陈设瓷,摆设瓷display china瓷porcelain, china (China ‘中国’来自’Chin’’秦’,在英文中’中国’和’瓷’同一单词)赤陶terracotta, terracotta, red earthenware代尔夫精陶delft德化陶瓷Te-hua porcelain, Dehua pottery高温陶瓷refractory china工业陶瓷industrial ceramics工艺瓷,美瓷,艺术瓷art porcelain, art and craft china, art pottery, artistic china 骨瓷bone china官瓷mandarin porcelain光瓷lusterware黑色陶器basalt裂变瓷crackled porcelain裂纹瓷crazed china米色陶器creamware青瓷celadon青花瓷bule and white porcelain轻质瓷、轻瓷light china日用瓷household china, table ware软瓷soft porcelain杀菌陶瓷antiseptic pottery绳纹陶器Jomon pottery施釉陶器slipware炻瓷stoneware素彩瓷plain porcelain陶earthenware陶瓷pottery无釉陶、陶瓷素烧坯biscuit, unglazed ware锡釉陶majolica细瓷fine china硬瓷hard porcelain赭色粘土陶器terra sigillata紫砂purple granulated, purple sand, terra-cotta 工艺技术Technology凹雕intaglio标记marking玻璃化vitrify车削turning成型forming冲压,冲压花repousse瓷土加工clay processing雕刻carving浮雕relief隔焰窑muffle工艺技术technology硅氧键silicon-oxygen bond技艺technique, craft间断窑intermittent kiln浇铸casting拉毛sgraffito连续窑continuous kiln镂雕、镂空piercing辘轳车jigger泥釉彩饰法trailing碾磨grinding抛光burnishing, polishing破裂chip嵌入inlay切刻incising筛子sieve烧制firing陶瓷科技ceramics陶轮potter’s wheel贴花、嵌花appliqué, decal凸雕，底切，拉底，底部掏槽undercut 细裂纹craze性能property压印impressing窑kiln印花stamping釉上彩overglazed color figure釉下彩underglazed color figure预加工pre-processing 粘性，粘滞性viscosity, stiffness转模片jiggered piece转印transfer print装饰décor, decoration半抛光：semi-polish，但意大利人形容半抛不说semi-polish而是用lappato来形容。
- 1、下载文档前请自行甄别文档内容的完整性，平台不提供额外的编辑、内容补充、找答案等附加服务。
- 2、"仅部分预览"的文档,不可在线预览部分如存在完整性等问题,可反馈申请退款(可完整预览的文档不适用该条件!)。
- 3、如文档侵犯您的权益，请联系客服反馈,我们会尽快为您处理(人工客服工作时间：9:00-18:30)。
Motor Electric contact thermometer Electric contact manometer Bearing plate Washer Screw Adjust rod Stacked relief valve Eject rod Eject beam Eject sleeve Position plate Position sleeve Dynamic valve adjusting rod Dynamic valve cover plate Dynamic valve Plug Terminal box bracket Bisect flange clamp Base accessory 2-position 2-channel solenoid valve 2-position 4-channel solenoid valve Valve plate Valve plate connecting tube Valve block Valve core Valve group Valve group bearing plate Valve base Flange Flange clamp Flange connecting tube Flange joint
K型特康斯特封 L型螺纹二通 O形密封圈 O形密封圈用挡圈 SAE法兰片 T型特康格来圈 Y型快插接头 埃落特 泵站 泵站支座 薄螺母 不锈钢丝 操作杆 测压接头 测压装置 插装阀 插装阀盖板 长回油管 长接头 齿轮套 齿盘 充气工具 单向阀 单向节流阀 弹簧 弹簧垫圈 弹簧压盖 导杆 导向块 导向套 等长双头螺柱 电磁比例阀 电磁阀
压力传感器 液控阀插件 液压锁 一层钢丝编织胶管 一层钢丝橡胶管 溢流阀 溢流阀过渡块 油杯 油缸 油路板 油马达控制块 油箱出油接管 油箱盖板 油箱体 增压法兰 增压缸 增压活塞 增压接管 支撑垫套 支撑轴 支撑座 直动溢流阀 轴 轴套 轴向柱塞泵 主泵出口过渡块 主泵进口接管 主泵联接套 主活塞 主油缸 撞块 紫铜垫圈 组合垫圈
Lock screw Cotter pin Flexible double-sphere rubber joint Control valve piston Control valve oil cylinder Spring hook Spring holder Spring Centrifugal pump oil-in pipe Connect rod Connect shaft Connecting plate Connecting pipe Hose coupling Press plate Hex nut Hex bolt Filter core Oil filter Filter inlet flange Nut Nut plug Bolt Thread sleeve Elastic coupler Inner hex screw plug Inner hex column screw Female thread column pin Joint Female tapered coupling Anti-friction ring Impact pin Accumulator
Flat washer Common flat key Pneumatic system Pneumatic cylinder bearing plate Cylinder 3-position 4-channel solenoid valve Upper flange Upper oil cylinder Upper shaft sleeve Handle ball (B) Double-end joint Step seal Lock nut Bushing Large washer Turcon slide ring Copper sleeve Worm reducer Lower flange Lowe oil cylinder Pilot overflow valve Limit sleeve Limit shaft sleeve Oil tank Pin shaft Small gear Draw bar Signal board Accumulator joint Press plate Press ring Manometer Manometer switch
电机 电接点温度计 电接点压力表 垫板 垫圈 吊环螺钉 调节杆 叠加式减压阀 顶杆 顶梁 顶套 定位板 定位套 动态阀调节杆 动态阀盖板 动态功能阀 堵塞 端子箱支架 对开法兰夹 耳座附件 二位二通电磁阀 二位四通电磁阀 阀板 阀板接管 阀块 阀芯 阀组 阀组垫板 阀座 法兰 法兰夹 法兰接管 法兰接头
K turcon step seal L thread 2-channel O-ring seal Circlip for O-ring seal Sheet SAE flange T turcon glide ring Y rapid plug joint Allot Pump station Pump station support base Nut Stainless steel wire Operating bar Pressure measuring joint Pressure measuring device Plug-in valve Plug-in valve cover plate Oil-return pipe Long joint Gear sleeve Fluted disc Inflator device One-way valve One-way hrottle valve Spring Spring washer Spring cover Guide bar Guide block Guide sleeve Double-head bolt Solenoid proportional valve Solenoid valve
法兰软管接头 法兰座 防尘圈 防松件 放气阀Ⅰ型 封盖 盖板 钢丝 高强度喉箍 格来圈 固定板 固定梁 过渡接块 过渡接头 过渡块 过渡油板 横杆 厚螺母 滑板 缓冲垫 换向阀过渡块 回油法兰软管接头 回油过渡接管 回油接管 回油弯管 活动横梁 活塞轴 集中润滑装置 胶管总成 铰接头 接头 接油盘 节流板
Pressure sensor Hydraulic control valve plug-in board Hydraulic lock Steel wired rubber pipe Steel wired rubber pipe Overflow valve Overflow valve transition block Oil cup Oil cylinder Oil-circuit plate Control block Oil -out pipe Tank cover Oil tank Supercharging flange Supercharging cylinder Supercharging piston Supercharger connecting tube Bearing sleeve Support shaft Support base Overflow valve Shaft Shaft sleeve Piston pump Pump outlet transition block Pump inlet connector Connecting sleeve Main piston Oil cylinder Impact block Copper washer Composite washer
紧定螺钉 开口销 可曲挠双球体橡胶接头 控制阀活塞 控制阀油缸 拉簧钩 拉簧座 拉伸弹簧 离心泵进油接管 连接杆 连接轴 联接板 联接管 联接软管接头 联轴器压板 六角螺母 六角头螺栓 滤芯 滤油器 滤油器进口法兰 螺母 螺母堵头 螺栓 螺套 梅花形弹性联轴器 内六角螺塞 内六角圆柱头螺钉 内螺纹圆柱销 内外接头 内锥接头 耐磨环 碰销 皮囊式蓄能器
Flange hose joint Flange base Dustproof ring Anti-loose part Air release valve I Sealed cover Cover plate Steel wire Hi-intensity clamp Glide ring Fixing plate Fixing beam Transition block Transition joint Transition block Transitional oil board Rod Thick nut Slide board Cushion pad Changeover valve transition block Oil-return flange hose joint Oil-return transition connector Oil-return pipe Oil-return elbow Movable crossbeam Piston shaft Centralized lubricating device Rubber pipe assembly Ream joint Joint Oil-taking disc Throttle plate
平垫圈 普通平键 气动系统 气动箱垫板 气缸 三位四通电液阀 上法兰 上油缸 上轴套 手柄球(B型) 双向接头 斯特封 锁紧螺母 套筒 特大垫圈 特开斯来圈 铜套 蜗杆减速器 下法兰 下油缸 先导式溢流阀 限位套 限位轴套 箱体 销轴 小齿轮 小拉杆 信号板 蓄能器接头 压板 压环 压力表 压力表开关