注塑常用英语
、浇口（入水）：gate
浇口进入位置：gate location 浇口形式：
gate type 大水口（2 板模）：edge gate,
side gate 细水口（3 板模）：pin-point gate
浇口大小：gate size 转开关流道：
switching runner/gate 唧嘴直径：sprue
diameter
二、流道：runner
热流道：hot runner ，hot manifold 温控
箱：temperature controller 热嘴冷流道：
hot sprue/cold runner 唧嘴直流：direct
sprue gate 圆形流道：round（full/half）
runner 模流道电脑分析：mold flow analysis
流道平衡：runner balance 热嘴：hot
sprue 热流道板：hot manifold 发热管：
cartridge heater 探温针：thermocouples 插
头：connector plug 插座：connector
socket 密封/封料：seal
三、运水：water line
喉塞：line plug 喉管：tube 塑胶管：
plastic tube 快速接头：jiffy quick connector
plug/socket
四、模具零件：mold components
三板模：3-plate mold 二板模：2-plate
mold 导柱（边钉/ 导边）:leader pin /guide
pin 导套（边司）：bushing/guide bushing
顶针板: ejector retainer plate 托板: support
plate 螺丝: screw 管销（管钉）: dowel pin
开模槽：ply bar slot 内模管位锁：core/cavity inter-lock 顶针：ejector pin 司筒：ejector sleeve 司筒针：ejector sleeve pin 推板：stripper plate 缩
呵：movable core ，return core ，core puller 扣机（尼龙拉勾）：nylon
latch lock 斜顶：lifter 模胚（架）：mold base 上内模：cavity insert 下内
模：core insert 行位（滑块）:slide 镶件：insert
压座（斜鸡）: wedge，heeled block 耐磨板/油板: wedge wear plate 压条: guide way plate 模顶（撑头）: support pillar 唧嘴: sprue bushing 挡板:
stop plate 定位圈: locating ring 锁扣: latch 扣鸡: parting lock set 推杆:
push bar 栓打螺丝: S.H.S.S.（socket head shoulder screw）杯头螺丝:
S.H.C.S.（socket head cap screw）活动臂: lever arm 分流锥: sprue
separator 垃圾钉: stop pin 水隔片: buffle 弹弓柱: spring rod 弹弓: die
spring 中托司: ejector guide bush 中托导套（边）: ejector guide pin 镶针: insert pin 波子弹弓: ball catch 喉塞: pipe plug
锁模块：lock plate 行位斜导柱：angle pin 斜顶杆：angle ejector rod 复位键/提前回杆：early return bar 气阀：valves
五、术语：terms 承压平面平衡：parting surface support balance 模排气：
parting line venting 回针碰料位：return pin and cavity interference 模闭合总厚度：mold base shut height 顶针碰运水：water line interferes with ejector pin 料位出上(下)模：part from cavity (core) side 模胚原身出料位：cavity
direct cut on A-plate ，core direct cut on B-plate. 不准用镶件：do not use
(core/cavity) insert 用铍铜做镶件：use beryllium copper insert 初步(正式)
模图设计：preliminary (final) mold design 反呵：reverse core 弹弓压缩
量：spring compressed length 强度不够：insufficient rigidity 均匀冷却：
even cooling 扣前模：sticking 热膨胀：thermo expansion 公差：
tolerance 铜电极(铜公)：copper electrode 石墨电极：graphite electrode 夹线：weld line 翘曲：warpage 缺胶：short shot 困气：air trap 毛刺：
flash ，burr
^w ^w ^w ^w ^w ^w ^w ^w ^w ^w ^w ^w ^w ^w ^w ^w ^w ^w ^w
^w ^w ^w ^w ^w ^w ^w ^w ^w ^w ^w ^w ^w
模具述语
一、入水：gate 进入位：gate location 水口形式：gate type 大水口：edge gate 细水口：pin-point gate
水口大小：gate size 转水口：switching runner/gate 唧嘴口径：sprue diameter 二、流道: runner 热流道：hot runner,hot manifold 热嘴冷流道: hot sprue/cold runner 唧嘴直流: direct sprue gate 圆形流道：round(full/half runner 流道电脑分析：mold flow analysis 流道平衡:runner balance 热嘴：hot sprue 热流道板：
hot manifold 发热管：cartridge heater 探针: thermocouples 插头：connector plug
插座：connector socket 密封/封料：seal
三、运水：water line 喉塞：line lpug 喉管：tube 塑胶管：plastic tube 快速接头：jiffy quick connector plug/socker
四、模具零件：mold components 三板模：3-plate mold 二板模：2-plate mold
边钉/导边：leader pin/guide pin 边司/导套：bushing/guide bushing 中托司：shoulder guide bushing 中托边L：guide pin 顶针板：ejector retainner plate 托板：support plate 螺丝：screw 管钉：dowel pin 开模槽：ply bar scot 内模管位：core/cavity inter-lock 顶针：ejector pin 司筒：ejector sleeve
司筒针：ejector pin 推板：stripper plate 缩呵：movable core,return core core puller 扣机（尼龙拉勾）：nylon latch lock 斜顶：lifter 模胚（架）：mold base 上内模：cavity insert 下内模：core insert 行位（滑块）：slide 镶件：insert 压座/斜鸡：wedge 耐磨板/油板：wedge wear plate 压条：plate 撑头: support pillar 唧嘴：sprue bushing 挡板：stop plate 定位圈：locating ring 锁扣：latch 扣鸡：parting lock set 推杆：push bar 栓打螺丝：S.H.S.B 顶板：eracuretun 活动臂：lever arm 分流锥：spure sperader 水口司:bush 垃圾钉：stop pin 隔片：buffle 弹弓柱：spring rod 弹弓:die spring
中托司：ejector guide bush 中托边：ejector guide pin 镶针：pin 销子：dowel pin 波子弹弓：ball catch 喉塞: pipe plug 锁模块：lock plate 斜顶：angle from pin
斜顶杆：angle ejector rod 尼龙拉勾：parting locks 活动臂：lever arm 复位键、提前回杆：early return bar 气阀：valves 斜导边：angle pin 术语：terms 承压
平面平衡：parting surface support balance 模排气：parting line venting 回针碰料位：return pin and cavity interference 模总高超出啤机规格：mold base shut hight 顶针碰运水：water line interferes withejector pin 料位出上/下模：part from cavith (core) side 模胚原身出料位：cavity direct cut on A-plate,core direct cut on
B-plate. 不准用镶件：Do not use (core/cavity) insert 用铍铜做镶件：use beryllium copper insert 初步(正式)模图设计：preliinary (final) mold design 反呵：reverse core 弹弓压缩量：spring compressed length 稳定性好：good stability,stable 强度不够：insufficient rigidity 均匀冷却：even cooling 扣模：sticking 热膨胀：thero expansion 公差：tolorance 铜公(电极)：copper electrode
*>■# *>■# *>■# *>■# *>■# *>■# *>■# *>■# *>■# *>■# *>■# *>■# *>■#
*>■# *>■# *>■# *>■# *>■# *>■# *>■# *>■# *>■# *>■# *>■# *>■# *>■#
*>■# *>■# *>■# *>■# *>■# *>■# *>■# *>■# *>■# *>■# *>■# *>■# *>■#
*>■# *>■# *>■# *>■#
Surface Appearance 外观Glossiness/gloss finish 光洁度Matt finish/matt surface 毛面Glass fiber rich surface/glass emergence on the surface 玻纤外露Blooming/surface blooming 表面析出White patches on surface 表面白斑
Silver marks/silver streak 银纹Splay mark 水纹Flow mark 流纹Weld line 溶结纹
Brittle/brittleness 脆
Bubbles/trapped gas 气泡
Void 孔
Burn marks 烧伤
FR failed 阻燃不合格
Flame rating V-2 阻燃V-2
Poor dispersion 分散不好
FR/PTFE …agglomerates etc 阻燃剂/PT FE… 结块
Pellet porous 粒子不密/蜜蜂窝
Low impact/tensile etc 物理性能低
High flow/filler content etc 流动性/填充…过高
Longs/fines/doubles 长粒/碎屑/连粒
Poor cut 粒形不好
Bristle/voids 表面有小气泡/孔
Glass bundles 玻纤结团
Product was rejected due to 产品不能接受因为… High moisture level 高水分Warpage/warped 翘曲
Shrinkage/shrink 收缩
Sink marks 缩影
Short shot/short molding 打不满
Distortion 变形
Over dimension 尺寸过大
Under dimension 尺寸过小
Flashing 飞边
Discoloration 变色
Off color 颜色差异
Flow rate 流动率
Viscous 粘
High flow 高流动
Low flow 低流动
Sticky 粘
Mold release 脱模
Antioxidant 抗氧剂
Flame retardant agent 阻燃剂
Heat stabilizer 热稳定剂
Chopped glass fiber 短切玻纤
Roving glass fiber 粗纱/长玻纤
Glass beads 玻璃微珠
Milled fiber 碾磨纤
Molybdenum disulfide/moly/MoS2 二硫化钼
Colorant 着色剂
Pigment 颜料
Dye 染料
Accepted product specification 接受产品规格
Approved our product 认可我们的产品
Re-set spec 重新定标准
Add in extra ?添加多一点…
Reduced…content减少…含量
Dropped/reduced …by X^ 减少…含量…％
Confirmed color standard 确认颜色标准
Approved color standard 认可颜色标准
Re-confirmed color standard 重新确认颜色标准
Qualified our product 认可我们的产品
Undergoing heat aging test 在做热老化实验
Product is under testing 产品在测试当中
Received first order 接了第一个定单
Expected to finish by 预…计在…完成
Expected order is xMT 预计定单量…吨
Estimated annual/monthly consumption 预计年/月用量
（注：范文素材和资料部分来自网络，供参考。只是收取少量整理收集费用，请预览后才下载，期待你的好评与关注）
模具专业英语词汇大全
模具专业英语词汇 A abrasion n. 磨损 abrasion resistance n. 耐磨损性 abrasive n. 磨料 accelerator n. 促进剂 accuracy n. 准确性 accurate die casting 精密压铸 air trap 积风 acrylic n. 丙烯酸 /压克力 ì active plate 活动板 additive n. 添加剂 adhere v. 黏附 adhesion n. 黏合 adhesive n. 胶粘剂 air-cushion eject-rod 气垫顶杆 air cushion plate 气垫板 air entrapment n. 困气 anneal v. 退火 assemble v. 总成 B back pressure 背压 bismuth mold 铋铸模 baffle plate 挡块 barrel n. 机筒 /料筒 / bending block 折刀 bottom block 下垫脚 bottom plate 下托板(底板) bushing bolck 衬套 barrel temperature 料筒温度 blush 发 blank through dies 漏件式落料模 burnishi blow molding n. 吹塑成型 blow molding machine n. 吹塑机 brittle adj. 脆性 bubble n. 气泡 burr 毛刺 button d by-product n. 副产品 C calendering n. 压延 carbon steel n. 碳素钢 casting n. 铸造 catalyst n. 催化剂 cavity n. 型腔 chemical resistance n. 耐化学腐蚀性 chip v. 削 /凿
注塑方面英语术语
注塑方面英语术语 压铸die-cast 压炼injection 铸件casting/cast/founding 起泡/气泡bubble/blister/air bubble 缺料shor-shots/undershot 浇不足/*铸under-founding 多料superfluities/superfluous material(alloy) 顶针痕ejector (pins) mark 花纹flow mark/flow line 冷纹cold mark/cold streak 油纹oil streak 走水纹splash mark 银纹silver streaks 霜纹splay mark 夹水纹silver streaks/flow line/weld line 扣模/粘模sprue sticking 砂眼/气眼air hole
（塑胶件）弯曲/变形warping/warpage 变形deformation 扭曲twist 翅曲warp/warped 材料错误using wrong plastic material 凸痕convex mark 凹位/凹陷sink mark/dent mark 披锋flashing 批损pare-mark/cut mark 批凹pare off 锉纹trim-mark/file-mark 锉损excessive trim mark 黑点/黑纹black spots/black streak 发白white mark 烧焦burn marks 刮花/刮痕scratch mark 擦痕/擦伤rub-mark/brush-burn 裂缝cracking 裂纹craking line
塑胶模具常用英语句型
塑胶模具常用英语句型 1. XXX！你现在有空吗，我可以问你一些问题吗？ Could I ask you some questions if you are free？/ Are you free now？ May I ask you some questions (a question)？ 2. 请问此产品的面是否为外观面？表面做什么处理？是晒纹/抛光？ Can you tell me whether the surface of this part is a visible/esthetic one？ What will we do for its？Surface？Texture or Polishing？ 3. 请问产品这个面可否加顶针或顶块？产品允许加扁顶针吗 Does this part need an ejector pin or an ejector bar? Can we add an ejector blade? 4. 这个产品的柱位我们打算做司筒。（或镶针）可以吗？ Can we add ejector sleeves or ejector pins in the boss of this part? 5. 产品的这个位置不能出模，我们打算做行位，在此面上会有分模线，你接受吗？ There's an undercut at this position and it needs a slider. It will also have a parting line on this side, is that OK? 6. 产品里面的这个位置我们打算做斜顶或内行位，有问题吗？ We will make the lifter and (inner) slider in this position, will that be a problem? 7. 你提供的2D产品图与3D产品图不一致，请问以哪一个图面为准？ The 2D and 3D drawing you provided is not the same, can you tell me which one is correct? 8. 你提供的3D产品图有的地方没有出模角，有的地方胶位太厚，有的地方胶位太溥，这些产品问 题我们可以自己修改吗？修改后会给交给你确认。 There is no draft angle in the 3D drawing, some materials are too thick, and some place are too thin. Can we modify this part by ourselves? We will send the drawing to you for you to check after we modify it. 9. 按你们提供的缩水率千分之五，这个模具的尺寸已经做到了模具图面要求。但注塑出来的产品 不符合你们的产品图。请确认你们的材料的缩水率是否正确？ According to the shrinkage one over two hundred, the mold has been done in the right dimension, but the part falls short to your part drawing, are you sure the shrinkage is right? 10. 产品的这个位置太小，导致模具钢料太溥，能够加宽这个位置吗？ This position is too small and will make the steel material here too thin, can we widen it here? 11. 斜顶与后面的柱位空间太小，斜顶在运动时会干涉到柱子，能移动这个柱子的位置吗？ The angular lifter interferes with the boss during ejection. Please consider changing the position of the boss. 12. 这个筋骨位胶厚太薄，而且高度偏高，注塑时很难填充这个筋位，可以增加这个筋骨位的厚度吗？ The rib here is too thin and on the high side, so it will be difficult to fill here when we do the injection, can you increase the thickness of this rib? 13. 你是想将此筋骨位的高度加高/减低吗？加胶的位置我们将用铜公放电加深。但减胶的位置有两 种做法，1、做镶件；2、烧焊；因为镶件的底部有运水，我们简单的做法是烧焊处理，你可以接受吗？ Will you increase/decrease the material on this rib? We will use EDM if you add material, but there are two option if you choose to decrease: 1. Make inserts;2 Welding, because there is water in the bottom of the insert, is that OK? 14. 这个样板的筋骨位底部烧焦，是因为排气不良，我们可以在筋骨位的中间增加一个镶件。
注塑机专业英语
注塑机专业英语Revised on November 25, 2020
钣金 machine cover / upper cover/ side cover锁模部分 clamping unit射胶部分 injection unit机架 machine frame / base电气系统 electric system液压系统 hydraulic system机械系统 mechanical system机门 safety door / fixed door / movable door锁模部分 clamping unit电脑控制器 computer controller机械安全锁 mechanical safety interlock射胶部分 injection unit液压系统 hydraulic system电箱 electrical cabinet / cable机架分体线 stand split line机架螺丝孔 foundation bolt hole机架machine base / supporting frame理论注射容积 theoretical shot volume 实际注射量 shot weight螺杆直径 screw diameter注射压力 injection pressure注射速度 injection speed注射速率 injection rate螺杆长径比screw L/D ratio螺杆行程 screw stroke螺杆转速 screw speed熔胶能力plasticizing capacity锁模力 clamping force开模/锁模行程 mold clamping / opening stroke模板尺寸 platen size拉杆间距 distance between tie bars / rods模板最大距离 max. daylight容模量 mold thickness (min. & max.)顶出行程 hydraulic ejection stroke顶出力hydraulic ejection force顶针数 nos. of ejector pin液压系统压力hydraulic system pressure油泵马达 pump motor电热量 heating capacity 温度控制区数 nos. of temp control zones射嘴接触力 nozzle contact force Injection射出 Cooling time 冷却时间 Holding time 锁模时间 Injection alarm time 射出警报时间 Injection start delay Final cushion minimum value Change-over to holding by value Plasticizing end value Hydrarlic change-over pressure holding Screwvalue for change-over to holding Change-over to holding by enable value Hydraulic pressure in holding 锁模压力 Filling stage pressure limit
塑胶模具专业英语
中文英文 机工,机器加工 machining,machine work O环,O形封垫 O ring 下料模,切料模 blanking die 寸进,寸动 inching 工程塑胶 engineering plastics 工模,夹具,支架 jig 干胶,粘著剂,动物胶 glue 干燥时间 drying time 干燥剂 drier dryer 不划一颜色,颜色深浅不均 color non-uni formity 中心浇口 center gate 内衬,衬套,衬蛰 liner 公差,容差 tolerance 分模线,合模线,模缝痕 parting line 切口,缺口 notch 切口,缺料 notch 切边(n) shear edge 化学腐蚀 chemical atching 化学腐蚀 chemical etching 反射 reflection 孔隙,空洞,气泡 void 尺寸稳定性 dimensional sability 手动压机 hand press 支管形喷嘴 nozzle manifold 比重 specific gravity 比热 specific heat 毛状裂痕 hair crack,hair cracking 毛绒 fuzz 毛边,凿纹 burr,flash,fin 水道,水通路 water channel 火花放电 spark discharge 火焰处理 flame treatment,flame treating 片材 sheet 凹痕,缩痕 sink mark,shrink mark 凹槽,内陷,凹陷 undercut 加料,给料,供料 feed 加热,加温 warming,warming up 加热板,热板(盘) heating plate 加热管套,加热缸 heating cylinder,heatin g barrel 加热炉 heating furnace 功率,力率 power factor 半透明 semitransparence,translucence 打眼,钻孔 driling 正余面,交叠,重叠 overlap 永久变形 permanent set,residual strain 白昙,雾状 haze 立式射出成型机 vertical injection mo(u)l ding machine 光彩,光泽 gloss 印刷 printing 同轴往复螺杆式射出成型机 in-line scre w(type)injecton mo(u)lding machine 合成树枝 synthetic resin 合板,集成材 composite wood 合模力,开模力 mo(u)ld clamping force, mo(u)ld locking force 合模线,毛边线 flash line,parting line 合模线,毛边线 spew line,spue line 合模销,导销 leader pin 合模销套,导销衬套 leader pin pushing 合模机构,开模机构 mo(u)ld clamping m echanism 后加工 post processing 后加热 after baking 后成型 postforming 回程销,复归销 return pin 安全系数 safety factor 安全门 safety door 成孔销,心型销,模蕊销 core pin 成孔销托板,动或定模板 core pin plate 成形 forming 成形,模制 mo(u)iding,forming
注塑机常用英语
注塑英语大全 成型工艺流程及条件介绍Molding technique procedure and parameter introduction 第一节成型工艺Section 1 molding technique.
1.成型工艺参数类型Sorts of molding parameter. (1).注塑参数ction parameter. a.注射量ction rate. b.计量行程Screw back position c.余料量Cushion d.防诞量Sucking back rate e.螺杆转速Screw speed f.塑化量Plastic0 rate g.预塑背压Screw back pressure h.注射压力和保压压力ction pressure and holding pressure i.注射速度ction speed (2)合模参数Clamping parameter a.合模力Clamping force b.合模速度Clamping speed c.合模行程.Clamping stroke d.开模力Opening force e .开模速度Opening speed f. 开模行程Opening position g.顶出压力Ejector advance pressure h.顶出速度Ejector advance speed i.顶出行程Ejector advance position 2.温控参数Temperature parameter a.烘料温度Dry resin material temperature b.料向与喷嘴温度Cylinder temperature and nozzle temperature c.模具温度Mold temperature d.油温Oil temperature 3.成型周期Molding cycle a.循环周期Cycle time b.冷却时间Cool time c.注射时间ction time d.保压时间Holding pressure time e.塑化时间Plant tim f.顶出及停留时间Knocking out and delay time g.低压保护时间Mold protect time 成型工艺参数的设定须根据产品的不同设置. Molding technique parameter setting differs depending on type of product 第二节成型条件设定Section 2 Molding parameter Setting 按成型步骤:可分为开锁模,加热,射出,顶出四个过程.Molding steps: mold opening/closing, heating ction and knocking out. 开锁模条件: Mold opening parameter: 快速段中速度High-speedmid-speed 低压高压速度Low pressure high pressure speed 锁模条件设定: Mold closing parameter setting 1锁模一般分:快速→中速→低压→高压 Mold closing: high-speed →low-speed →low pressure→high pressure
模具专业英语——注塑模
Injection Mold Technical Terms 特克内克腾目思 （一）模具专业基本用词 Professional Terms Intensification Factor 增强比 Scientific molding 科学注塑英腾次分克深发克偷 塞音特菲克计数器counter康特 Specific Injection Pressure (Psi)特殊注塑压力 思呗色服克 1．塑料—plastic, resin瑞申油管：Oil pipe 尼龙--------nylon 2．样件—sample 调节板-------adjust plate 3．钢料—steel A板--------a plate 4．注塑机—injection machine, press 定位圈----locating ring 喽客厅令 5．产品—part, product, moulding 斜导柱-----angular pin 安给拉PIN 6．模具—mold, mould, tool B板--------- b plate A 简易模（样板模）—prototype mold B 量产用模具—production mold 7．三维造型（数模）—3D model, 滚珠导套-------ball ejector bush 8．二维产品图—2D part drawing 拽应扁顶针--------blade ejector pin 布累得 9．设计—design 低赛应下模板--------bottom clamping plate 抱腾 10．制造—manufacture, 上模型腔------cavity main insert 11．检验—check, 上模镶件------cavity sub insert 12．测量—measure, 妹试司筒针--------center pin 深特 13．修改—change, modify 下模型芯------core main insert 14．工程更改—engineer change 下模镶针------core pin 15．质量—quality 快乐体下模镶件------core sub insert 16．数量—quantity 宽体踢延迟顶针-------delay ejector pin 17．基准—datum, reference 拉杆限位钉--------distance bolt （二）如何解析2D 产品图？How to read 2D part drawing? 一．产品几何Geometry 顶距限位柱--------distance spacer 1．点—point 销钉-------dowel pin 2．线（边）—line, edge 顶块--------ejector bar 3．面face 顶板导套-----ejector leader pin A 侧面—side塞得 B表面—surface射飞思 C 外观面—appearance surface安皮尔思射飞思4．壁厚—wall thickness 我射克来思顶板导柱----ejector leader pin李德拼 5．加强筋（骨位）—rib 瑞布顶针-------ejector pin 6．孔—hole后顶针地板------ejector plate 7．细长的槽—slot 顶针面板-----ejector retain plate 瑞腾 8．柱位—boss 抱死顶棍------ejector rod
注塑专业词汇翻译
成型工艺流程及条件介绍 Molding technique procedure and parameter introduction 第一節成型工艺Section 1 molding technique. 1.成型工艺参数类型 Sorts of molding parameter. (1). 注塑参数 Injection parameter. a.注射量 Injection rate. b.计量行程Screw back position c.余料量Cushion d.防诞量Sucking back rate e.螺杆转速Screw speed f.塑化量Plastic0 rate g.预塑背压Screw back pressure h.注射压力和保压压力Injection pressure and holding pressure i.注射速度Injection speed (2)合模参数Clamping parameter a.合模力Clamping force b.合模速度Clamping speed c.合模行程.Clamping stroke d.开模力Opening force e.开模速度Opening speed f.开模行程Opening position g.顶出压力Ejector advance pressure h.顶出速度Ejector advance speed i.顶出行程Ejector advance position 2.温控参数Temperature parameter a.烘料温度Dry resin material temperature b.料向与喷嘴温度Cylinder temperature and nozzle temperature c.模具温度Mold temperature d.油温Oil temperature 3.成型周期Molding cycle a.循环周期Cycle time b.冷却时间Cool time c.注射时间Injection time d.保压时间Holding pressure time e.塑化时间Plant time f.顶出及停留时间Knocking out and delay time g.低压保护时间Mold protect time 成型工艺参数的设定须根据产品的不同设置. Molding technique parameter setting differs depending on type of product 第二节成型条件设定Section 2 Molding parameter Setting
模具专业英文术语大全
实用文案 模具英语专业术语 模具述语开模槽：ply bar scot 内模管位：一、入水：gate core/cavity inter-lock 顶针：ejector pin 进入位：gate location 司筒：ejector sleeve 水口形式：gate type 司筒针：edge gate ejector pin 大水口：推板：细水口：stripper plate pin-point gate 缩呵：gate size movable core,return core core 水口大小：puller switching runner/gate 转水口：扣机（尼龙拉勾）：nylon latch lock sprue diameter 唧嘴口径：斜顶：lifter : runner 二、流道模胚（架）：mold base hot runner,hot manifold 热流道：上内模：cavity insert : hot sprue/cold runner 热嘴冷流道下内模：core insert : direct sprue gate 唧嘴直流行位（滑块）：slide round(full/half runner 圆形流道：镶件：insert mold flow analysis 流道电脑分析：压座/斜鸡：wedge :runner balance 流道平衡耐磨板/油板：wedge wear plate hot sprue 热嘴：压条：plate hot manifold 热流道板：撑头: support pillar cartridge heater 发热管：唧嘴：sprue bushing : thermocouples 探针挡板：stop plate connector plug 插头：定位圈：locating ring connector socket 插座：锁扣：latch seal 封料：/密封扣鸡：parting lock set water line 三、运水：推杆：push bar line lpug 喉塞：栓打螺丝：S.H.S.B tube 喉管：顶板：eracuretun plastic tube 塑胶管：活动臂：lever arm jiffy quick connector 快速接头：分流锥：spure sperader plug/socker 水口司mold components 四、模具零件：:bush 垃圾钉：三板模：3-plate mold stop pin 隔片：buffle 二板模：2-plate mold 弹弓柱：导边：/leader pin/guide pin spring rod 边钉弹弓:die spring 导套：边司/bushing/guide bushing 中托司：ejector guide bush 中托司：shoulder guide bushing 中托边：ejector guide pin guide pin ：L中托边镶针：ejector retainner plate 顶针板：pin 销子：托板：support plate dowel pin 波子弹弓：ball catch screw 螺丝：: pipe plug dowel pin 管钉：喉塞文案大全． 实用文案 锁模块：lock plate Mold repair 模具维修 angle from pin 斜顶：Molds 模具
注塑模具英文论文
Low Cost Injection Mold Creation via Hybrid Additive and Conventional Manufacturing 1. Introduction In most industrial applications, the manufacturing cost of a plastic part is mainly governed by the amount of material used in the molding process. Thus, current approaches for plastic part design and manufacturing focus primarily on establishing the minimum part thickness to reduce material usage. The assumption is that designing the mold and molding processes to the minimum thickness requirement should lead to the minimum manufacturing cost. Nowadays, electronic products such as mobile phones and medical devices are becoming ever more complex and their sizes are continually being reduced. The demand for small and thin plastic components for miniaturization assembly has considerably increased in recent years. Other factors besides minimal material usage may also become important when manufacturing thin plastic components. In particular, for thin parts, the injection molding pressure may become significant and has to be considered in the first phase of manufacturing. Employing current design approaches for plastic parts will fail to produce the true minimum manufacturing cost in these cases. Thus, tackling thin plastic parts requires a new approach, alongside existing mold design principles and molding techniques. 1.1 Current research Today, computer-aided simulation software is essential for the design of plastic parts and molds. Such software increases the efficiency of the design process by reducing the design cost and lead time [1]. Major systems, such as Mold Flow and C-Flow, use finite element analysis to simulate the filling phenomena, including flow patterns and filling sequences. Thus, the molding conditions can be predicted and validated, so that early design modifications can be achieved. Although available software is capable of analyzing the flow conditions, and the stress and the temperature distribution conditions of the component under various molding scenarios, they do not yield design parameters with minimum manufacturing cost [2,3]. The output data of the software only give parameter value ranges for reference and leaves the decision making to the component designer. Several attempts have also been made to optimize the parameters in feeding [4–7], cooling [2,8,9], and ejection These attempts were based on maximizing the flow ability of molten material during the molding process by using empirical relation ships between the product and mold design parameters.
模具DFM常用中英文对照
DFM常用中英文对照 15、如果分型面此处，模具上会有尖角和刀口，对模具寿命有影响。. There are sharp edges if we set the parting line here, it will reduce the tool life. 16、此处料厚段差很大，成品表面会有应力痕，建议修改如图示。. The thickness is not equal and it will bring the stress lines on the surface, suggest to improve the part as the picture shown. 17、此大行位上有小行位，开模时小行位需先退，大行位做延时，合模时则相反。. The small slider is inside the big slider, when the mold open, the small slider need to recede first and the big slider have to postpone. When the mold close, it is contrary. 18、此处需做强顶。. This position need to force ejection. 19、由于此处没有足够空间下热咀，所以需做一个柱子进胶。. This position need to make a pole for gating because there have no enough space for hot sprue. 20、沾模， Stick 1.High shrinkage values could indicate sink marks or voids at gate location 高缩水率的产品容易产生缩印，但在浇口附近可以避 免。. 2.Welding line on the cosmetic surface 熔接线在外表面 3.Two banana gate was to being confluent in the end of melt flow. 两个香蕉浇口在流动未端熔合。. 4.Venting insert here has flash 排气镶件处有飞边 5.Venting gap between inserts is too big 镶件处的排气槽过大 6.Stress mark on the cosmetic surface 产品外表面上有压痕 7.Uneven thickness 不平均的产品壁厚 8.Unreasonable product structure 不合理的产品结构 9.Injection speed is high 注塑压力过高 10.There is black spot on the cosmetic surface 产品外表面上有黑色点 11.There is flash on the product 产品有飞边 12.there is sink mark on the cosmetic surface 产品外表面上有缩痕 13.Gate size is not reasonably 浇口尺寸不合理 14.There is argent spot 这里有亮点（银色斑点） 15.The plastic of first shot didn't meet high temperature. 塑料的第一胶不会有很高的温度。. 16.Make sure the core float plate was closed before lifter completely return to correct position 确认lifter完全回位时core侧 浮动板已经复位 17.Make sure the ejector system is smooth 确认顶针系统移动平稳 18.Add early return structure to protect lifter return to correct position 增加先复位机构保护lifter回到正确位置。. 19.Propose to add draft on slider side wall and draw polish. 建议增加slider的角度和抛光角度。. 20.It is too thin and very difficult to inject fully, and weakness wall will have risk of the part function 该处壁厚过薄而造成很难去 填充完整，薄壁将会有产品功能上的风险。. 21.These are will have sink marks due to uneven thickness, propose to reduce plastic. 壁厚不均匀容易产生缩印，建议在该处减胶。. 22.These are will have sink marks due to ribs opposite. 正面的筋位易导致背面产生缩印。. 23.Please confirm the 3D part thickness whether has including painting thickness or not? 请确认产品的设计是否考虑到油漆的厚 度。.
专业英语注塑成型专业词汇
专业英语---注塑成型专业词汇 Injection machine 啤机 Shot size（weight）实际射胶量injection volume 理论射胶量min mold height 最小容模厚度 Max mold height 最大容模厚度Tie bar clearance 拉杆间距Die plate size 模板尺寸 Ejector stroke 顶出行程barrel 炮筒，机筒clamp force 锁模力 non-return valve 止回阀 shear 剪切opening 开模行程Injection pressure 射胶压力back pressure 背压 nozzle size 射咀尺寸Cycle time 循环周期down time 停机时间hopper 料筒Mold release 脱模剂lubrication 润滑work horse 主力，主要 设备 Reserve pressure/packing pressure保压mold trial 试模shot （一）啤Decompress 减压oven 烤炉，烘灶shrinkage rate 收缩率Residence time 滞留时间 injection speed 注射速度booster time 增压时间Compression ratio 压缩比 mold close time 合模时间 Resin 胶料 Plastification 塑化，增塑viscosity 粘性，粘度contamination 污染，杂 物 Thermoplastic 热塑性塑料thermosetting plastics 热固性塑料Booster time 增压时间 feed 喂料，填充purge 净化Flame retardant 阻燃degradation 降解， 软化 regrind 再粉碎Water absorption 吸水reinforce 增强，加固specific gravity 比重
制造业常用英语词汇
制造业常用英语词汇 制造业常用英语词汇－－强烈推荐!!! 一、部门及职位名称 总经理办公室General manager’s office 模具部Tooling department 项目部Project department 品质部Quality department 计划部Plan department 制造部Manufacture department Keypad产品部Keypad department IMD 产品部IMD department 五金部Metal stamping department 设计科Design section 冲压车间Stamping workshop 电镀车间Plating workshop 物控科Production material control section 计划科Plan section 仓务科Warehouse section 商务科Business section 品质规划科quality plan section IQC科IQC section IPQC科IPQC section
OQC科OQC section 检测中心measurement center 项目规划科Project plan section 项目XX科Project section XX 试模科Mold test section 成本科Cost section 设备科Facility section 采购科Purchase section 综合办General affairs office 编程科Programming section 模具工程科Tooling engineering section 模具装配车间Mold assembly workshop 文控中心Document control center (DCC) 注塑车间Injection workshop 喷涂车间Spray painting workshop 装配车间Assembly workshop 总经理General manager (GM) 经理manager XX部门经理Manager of XX department 原料库Raw material warehouse 半成品库Semi-finished product warehouse 成品库Finished product warehouse