能源之星(中文版)

能源之星

Table of Contents

内容

Section 1: Definitions 2

第一部分：定义2

Section 2: Qualifying Products 4

第二部分：合格产品

Section 3: Energy Efficiency Specifications for Qualifying Products 4

第三部分：合格产品的能效规格

Table 1: Indoor Fixtures 4

表1：室内灯具

Table 1A: Additional Requirements for Indoor Recessed Downlight Retrofit Kits 8

表1A：嵌入式室内筒灯系列的额外要求

Table 2A: Outdoor Fixtures: Compliance Through Efficient Light Source 10

表2A：室外灯具：适合高效的灯源

Table 2B: Outdoor Fixtures: Compliance Through Reduced Operating Time 12

表2B：室外灯具：光感型

Section 4: Qualification Process, Testing Facilities, Standards & Documentation 13

第四部分：检验过程，测试设施，标准&文本资料

Table 3: Reference Standards and Required Documentation 15

表3：参考标准&资料

Section 5: Additional Quality Assurance Requirements 28

第五部分：额外的质量保证要求

Section 6: Effective Date 29

第六部分：有效期

Section 7: Future Specification Revisions 29

第七部分：预计规格一览表

ENERGY STAR_ Program Requirements for

Residential Light Fixtures

民用灯具能源之星计划

Eligibility Criteria – Version 4.0

标准－版本4.0

Below is the product specification (Version 4.0) for ENERGY STAR qualified residential light fixtures. A product must meet all of the identified criteria if it is to be labeled as ENERGY STAR by its manufacturer.

以下是能源之星合格民用灯具产品规格（4.0版本）。凡厂家标有ENERGY STAR（能源之星）的产品都需符合标准。

The intent of ENERGY STAR for Residential Light Fixtures is to move consumers from traditional incandescent fixtures to fixtures that use high-quality fluorescent or other energy-efficient technologies, including motion-sensors and

daylight-sensors for outdoor fixtures.

ENERGY STAR（能源之星）民用灯具系列把消费者从传统的白炽灯带到高质量的荧光灯或高效能源灯具系列的时代,包括室外灯具系列震动传感器&日光灯传感器。

1)

Definitions: Below is a brief definition of a light fixture and other related terms as relevant to ENERGY STAR:

定义：以下是灯具概述和相关能源之星（ENERGY STAR）术语。

ALA: American Lighting Association.

A.

ALA：美国照明协会

ANSI: American National Standards Institute.

B.

ANSI 美国国家标准协会

B.

C. APLAC: Asia Pacific Laboratory Accreditation Cooperation (NVLAP MRA Signatory).

APLAC: 亚太实验室认可合作（NVLAP MRA 签名）

C.

D.

Automatic Daylight Shutoff: A photocell device that automatically prevents operation of a fixture during

daylight hours.

Automatic Daylight Shutoff:白天光电池自动关闭灯具。

D.

Ballast: A device used with an electric-discharge lamp to obtain the necessary circuit conditions (voltage,

E.

current, and waveform) for starting and operating.

Ballast:是使放电稳定（电压，电流，波形）而与放电灯一起使用的器件。.

E.

Ballast Frequency: The frequency at which the ballast operates the lamp, measured in Hertz (Hz) or Kilohertz

F.

(kHz).

Ballast Frequency:指镇流器启动灯时的频率，单位是赫兹或千赫。

F.

CIE: Commission Internationale de l’Eclairage.

G.

CIE:国际照明委员会。

G.

Color Rendering: The effect that the spectral characteristics of the light emitted by the lamp has on the color

H.

appearance of the objects illuminated by the lamp. Color Rendering Index is measured on a scale of zero to

100, and is defined in terms of a comparison of the spectral tri-stimulus values of the objects under test

illumination and a reference or standard illumination according to the recommendations of CIE Publication No.

13.3.

H.显色性：光源对物体真实颜色的呈现程度称显色性。为了对光源的显色性进行定量的评价，引入显色指数的概念，

以标准光源为准，将其显色指数定伟100，其余光源的显色指数均低于100，该标准由国际照明委员会CIE第13.3版次发行。

Compact Fluorescent Lamp: A single based fluorescent lamp with a plug-in lamp base, including multi-tube,

I.

multibend, spiral, and circline types.

精致型荧光灯：单底座带插拔灯头的日光灯，包括多管式，多带式，螺旋式以及环形。

I.

Correlated Color Temperature (CCT): The actual color of the lamp is called the color temperature and is J.

defined in terms of the spectral tri-stimulus values (color coordinates) according to the recommendations of

IESNA LM-16. For color coordinates near the Black Body loci, the correlated color temperature, measured in

Kelvin (K), is used.

J.

相关色温：当光源发出的光的颜色与黑体在某一温度下辐射的颜色接近时，黑体的温度就称为该光源的相关色温，单位为K.

Electronic Ballast: A ballast which uses semi-conductor components to increase the frequency of fluorescent K.

lamp operation. Fluorescent system efficiency is increased due to the higher frequency.

电子镇流器：用半导体材料的荧光灯提高荧光灯操作频率。

K.

L. IEC: International Electrotechnical Commission.

IEC：国际电工协会

L.

M. IESNA: Illuminating Engineering Society of North America.

北美照明工程社

IESNA:

M.

N. ILAC: International Laboratory Accreditation Cooperation (NVLAP MRA Signatory).

亚太实验室认可合作（NVLAP MRA 签名）

ILAC:

N.

O. Input Power: The actual total power used by all lamp(s) and ballast(s) of the light fixture during operation, as measured in watts (W).

输入功率：所有灯具和灯具镇流器的实际操作功率。

O.

Lamp:A generic term for a manufactured source of light. By extension, the term is also used to denote sources P.

that radiate in the visible spectrum.

灯：生产光源的普通术语。延伸义是可见光谱的定义光源。

P.

Q. Lamp Ballast Platform: A pairing of one ballast with one or more lamps that can operate simultaneously on that ballast. A unique platform is defined by the manufacturer and model number of the ballast and lamp(s) and the quantity of lamps that operate on the ballast.

灯镇流器平台：指一对镇流器能同时操作一至二盏灯。单个的平台由生产镇流器和灯的厂家规定。

Q.

R. Lamp Current Crest Factor: For 60Hz operation, the ratio of peak lamp current to the root mean square (RMS) lamp current. For high-frequency (HF) operation, the highest peak lamp current of the modulation envelope (when evaluated over a full line voltage cycle) to the root mean square (RMS) of the lamp current.

R.为灯电流的最大峰值与均方根有效值(RMS)之比。为避免操作阴极，标准规定LCCF 不得超过1.7 。

S. Lampholder: A component of a fixture, which supplies power to the lamp and also holds the lamp in place.

灯座：灯具的组成部分，为灯提供电力以及固定灯的作用。

S.

T. Light Fixture (Luminaire): A complete lighting unit consisting of a lamp or lamps and ballasting (when

applicable) together with the parts designed to distribute the light, position and protect the lamps, and connect the lamps to the power supply.

灯具：一个完整的灯具由灯、镇流器（需要时）、发光体、护灯罩、电源线。

T.

U. Linear Fluorescent Lamp: A double based fluorescent lamp with a plug-in lamp base, including straight shaped or U-bent types.

线型荧光灯：带插拔灯头的双头荧光灯，包括直管型、U型。

U.

V. Magnetic Ballast: A ballast which uses a magnetic core and copper winding and operates at the frequency of the line voltage.

V.

电磁镇流器：该镇流器用磁芯，铜线以穿了电压操作。

W. MRA: Mutual Recognition Arrangement.

双方协议

W.

MRA:

X. NACLA: National Cooperation for Laboratory Accreditation (NVLAP MRA Signatory).

亚太实验室认可合作（NVLAP MRA 签名）

NACLA:

X.

Y. NEMA: National Electrical Manufacturers Association.

国际电气生产协会

Y.

NEMA:

Z. NFPA: The National Fire Protection Association (United States), which develops the National Electrical Code (NEC).

美国国家消防协会开发国家电气规范（NEC）。

Z.

NFPA:

AA. NRTL: Nationally Recognized Testing Laboratory as recognized by OSHA’s NRTL Program, which is a part of OSHA’s Directorate of Technical Support.

国家公认测试实验室是OSHA技术支持指令计划的一部分。

NRTL:

AA.

BB. NVLAP: National Voluntary Laboratory Accreditation Program.

国家自愿实验认证可计划。

NVLAP:

BB.

CC. Optics: Include reflectors, baffles, lenses and/or diffusers, all which control the light distribution and the

appearance of the lighted fixture.

CC.光学：控制光线分布和灯具外形的反射体、折流板、镜头和/或漫射罩等

DD. OSHA: Occupational Safety & Health Administration.

OSHA: 职业安全&保健部门

DD.

EE. Pigtail: A short piece of cable with two connectors on each end for converting between one connector type and another; also referred to as a screw-based adapter and socket adapter.

Pigtail（短花花线圈）: 连接2个连接器短电线，有时指带螺丝的适配器和插座适配器。

EE.

FF. Power Factor: The active power divided by the apparent power (i.e., the product of the rms input voltage and rms input current of a ballast).

FF.功率系数：有效功率与视在功率之比。（如镇流器的输入电压和电流）

GG. Recessed downlight retrofit kit: A non-linear lighting unit consisting of lamp(s), ballasting, optics, trim, and power supply connection designed to convert an incandescent or halogen type Insulated Ceiling (IC) or non-IC recessed downlight into an air-tight fixture that uses an energy-efficient light source.

嵌入式筒灯系列：由灯、镇流器、光学器件、装饰物以及电源连接器组成将白炽灯或卤素绝缘面或导热面筒GG.

灯转化成气密的节能灯。

HH. Standardized Color Ellipse: An elliptical region of chromaticity coordinates that is defined using a centroid,

a tilt angle relative to a horizontal axis, and a defined level of variance. Such a region defines what

chromaticity coordinates can be acceptably associated with a target Correlated Color Temperature. For this specification, standardized color ellipses are defined using centroids based upon objective chromaticities (x,y) and tilt angles (è) specified in Table 1 and 2 of ANSI C78.376-2001, and a defined variance of seven steps.

HH.

标准测量数据色普：色光的背面偏离质心的倾斜角度部分。该定义可同相关色温定义联系起来。质心偏移的色光阴影规格参见ANSI C78.376-2001表1、表2，定义差异分7步。

II. Trim: Trim is the part of the downlight that covers the ragged edge of the ceiling cut-out. The trim may be a separate ring, or trim ring, or it may be integrated with the optics (i.e., a self-flanged reflector). Airtight or

non-airtight.

装饰：指罩住筒灯面凸出边缘的修饰部分。装饰部分可以是单独的环、装饰环、或完整的光学器件（如折边反射 II.

罩）。气密型或非气密型。

JJ. UL: Underwriters Laboratories.

JJ. UL: 保险实验室

2) Qualifying Products: The ENERGY STAR Residential Light Fixture specification covers the requirements for indoor and outdoor light fixtures and recessed downlight retrofit kits intended primarily for residential type applications. For the purposes of this ENERGY STAR specification, residential applications include single-family and multi-family dwellings (such as houses and apartments), dormitories, public or military housing, assisted-living facilities, motels and hotels, and some light commercial applications.

2）合格产品：能源之星民用灯具规格涵盖室内、户外灯具，民用嵌入式筒灯。适用于居民娶（如别墅和公寓），宿舍，公共或军事住房，商业住房等。

Exclusion of magnetic ballasts: Indoor fixtures that use magnetic ballasts cannot be ENERGY STAR qualified under this Version 4.0 specification. Only outdoor fixtures that use high intensity discharge (HID) lamps, such as metal halide and high pressure sodium, may continue to use magnetic ballasts.

电感镇流器不适用范围：室内灯具使用电感镇流器不适合能源之星4.0规格的产品。仅仅高强度室外放电灯（如金属卤素灯，高压钠灯）适用电感镇流器。

Allowance of self-ballasted pin based lamps:Indoor and outdoor fixtures that use self-ballasted pin based lamp can be ENERGY STAR qualified fixtures if all applicable requirements for qualifying products (Table 1 & 1A for indoor fixtures or Table 2A or 2B for outdoor fixtures) are met. This includes the requirement that the average rated life of the lamp must meet or exceed 10,000 hours and that the maximum measured ballast case temperature during normal operation inside the fixture(s) does not exceed the ballast manufacturer maximum recommended temperature. In addition for ballasts that drive lamps 26 watts and lower the line-voltage socket must comply with the standard design developed by EPA and industry. Specific technical details for this standard design are located at:

https://www.360docs.net/doc/b75925531.html,/programs/lightingTransformation/lineVoltage/index.asp

自震式插脚灯适用范围：若满足合格产品的要求（表1& 1A的室内灯具或表2A或表2B的室外灯具规格），采用自震式插脚灯的室内户外灯具属于能源之星的合格产品。灯的平均寿命必须≥10，000小时，灯具正常操作下镇流箱温度的低于厂家注明的温度最大值。此外，镇流器启动灯功率为26w，低于EPA（美国环保署）标准。技术规格请参见

https://www.360docs.net/doc/b75925531.html,/programs/lightingTransformation/lineVoltage/index.asp

Temporary allowance for decorative LEDs:EPA encourages the use of innovative light source technologies such as LEDs. LEDs used as decorative lighting elements in residential lighting fixtures and ceiling fan light kits are allowed as long as the total wattage of the LEDs does not exceed five (5) watts, the average LED system (LED and driver) efficacy is at least 20 lumens per watt, and the LED is used to supplement a primary light source that meets all of the applicable performance characteristics outlined in the Eligibility Criteria. The ENERGY STAR Partner must supply the following LED information to EPA: total wattage consumed by all the LEDs, manufacturer warranty, an LED manufacturer specification sheet that shows wattage, efficacy, LED life, color, and lumen depreciation. This is

a temporary allowance for the use of LEDs; EPA plans to develop more comprehensive specifications for LED

performance as the technology advances and becomes more widely used in residential applications.

装饰LED（发光二极管）临时许可：EPA（美国环保署）鼓励使用革新的LED电源技术。在LED功率不超过5w的条件下,LED可用于居民装饰灯具和天花扇灯具，合格标准注明LDE可作为主要光源的补充灯源。能源之星合伙人必须将LED 的信息提供给EPA：所有LED的总功率，厂家保证，注有功率，光效，LED寿命，颜色和光衰的厂家规格单。为使LED更广泛的运用于居民照明灯具中，EPA决定开发LED更先进的性能规格。

3) Energy-Efficiency Specifications for Qualifying Products: Only those products listed in Section 2 that meet the criteria

below may qualify as ENERGY STAR. Specifications for qualifying indoor fixtures can be found in Table 1.

Specifications for qualifying recessed downlight retrofit kits can be found in Table 1A. Specifications for qualifying outdoor fixtures can be found in either Table 2A – Outdoor Fixtures: Compliance Through Efficient Light Source, or Table 2B – Outdoor Fixtures: Compliance Through Reduced Operating Time.

3）合格产品的能源功效规格：仅仅在第二部分列出的标准符合能源之星的规格。室内照明规格见表1。嵌入式筒灯系列规格见表1A。合格的户外灯具规格见表2A－户外灯具：适合高效灯源，或表2B－户外灯具：适合操作时间减少。

ENERGY STAR_ Program Requirements for

Residential Light Fixtures

能源之星－民用灯具计划

Eligibility Criteria – Version 4.0

Table 1 - Indoor Fixtures

合格标准－4.0版次

表1－室内灯具

Performance Characteristic 功能ENERGY STAR Specification 能源之星规格

Note: Only electronic ballasts may be used to meet the requirements of this table. In addition, fixtures that utilize compact fluorescent lamps that do not have a plug-in base (i.e use a mogul, medium, or other screw base) are not eligible to earn the ENERGY STAR.

注：仅仅电子镇流器满足该表的需要。此外，灯具要用不带插拔头的精致型荧光灯（如mogul端尖基座，中型头或螺丝头）不在能源之星之列。

Combined Lamp & Ballast Requirements:

灯& 镇流器组合灯具需求

System Efficacy Per Lamp

Ballast Platform in Lumens Per Watt (LPW)1

, 每盏灯的系统功效

镇流器平台（流明/瓦LPW ）

> 50 LPW for all lamp types below 30 total listed lamp watts.

> 60 LPW for all lamp types that are < 24 inches and > 30 total listed lamp watts. >70 LPW for all lamp types that are > 24 inches and > 30 total listed lamp watts.

> 50 LPW ，所有灯具总瓦特数大于30时

> 60 LPW 所有灯型< 24英寸>所有灯具总瓦特数为30时 > 70 LPW 所有灯型>24英寸>所有灯具总瓦特数为30时

Lamp Requirements: 灯必备条件： Lamp Life 灯寿命

For lamps shipped with the fixtures, the average rated life of the lamp must be > 10,000 hours.

If the lamp is not shipped with the fixture, product packaging must meet the

requirements set forth in the “Product Packaging for Consumer Awareness” section of this Table.

带灯支架的灯具：灯额定寿命必须>10，000小时

不带灯支架的灯具：其产品包装要符合该表的“消费者认可包装”。

Lumen Maintenance 流明维护系数

For lamps indicated on the fixture packaging or shipped with the fixtures, the lamp shall have an average rated lumen maintenance of at least 80% of initial lamp lumens at 40% (4,000 hours minimum) rated lamp life.

灯具包装上注明的灯或带支架的灯具，该灯的额定流明维护系数至少是出厂灯泡的80％，灯寿命是额定灯泡的40％（最小是4，000小时）。

Color Rendering Index 显色指数

For lamps shipped with the fixtures, the color rendering index must meet the following requirements:

> 80 for compact fluorescent lamps. > 75 for linear fluorescent lamps.

If the lamp is not shipped with the fixture, product packaging must meet the

requirements set forth in the “Product Packaging for Consumer Awareness” section of this Table.

带支架的灯具，显色指数符合以下要求; >80(精致型灯) >70（线型灯）

不带灯支架的灯具：其产品包装要符合该表的“消费者认可包装”。

Correlated Color Temperature 相关色温

For lamps shipped with the fixtures, the lamps must have one of the following designated correlated color temperatures (CCT): 2700K, 3000K, 3500K, 4100K, 5000K, or 6500K.

If the lamp is not shipped with the fixture, product packaging must meet the

requirements set forth in the “Product Packaging for Consumer Awareness” section of this Table.

带支架的灯具，灯相关色温CCT 如下：2700K, 3000K, 3500K, 4100K, 5000K, or 6500K.

不带灯支架的灯具：其产品包装要符合该表的“消费者认可包装”。

Lamp/Lampholder Compatibility

灯/灯座兼容性For lamps indicated on the fixture packaging or shipped with the fixtures, lamps must utilize an ANSI/IEC standardized lamp base configuration, as defined by ANSI C81.61 and IEC 60061-1.

The lampholder must be designed to accept lamps with ANSI/IEC standardized lamp base configurations for all applicable wattages. For example, if the ballast can operate lamps with multiple wattages (e.g., an 18W, 26W, or 32W lamp) then the lampholder must be designed to accept lamps with ANSI/IEC standardized lamp base configurations for all three applicable wattages.

In addition, lamps shall either:

? Meet the requirements of an ANSI/IEC standardized lamp specification sheet, as defined by ANSI C78.901-2001 and IEC 60901 (for compact fluorescent lamps) or ANSI C78.81-2001 and IEC 60081 (for linear lamps) if an applicable standard exists, or,

? If no ANSI/IEC lamp standard exists (e.g., a spiral compact fluorescent lamp), a custom lamp specification sheet must be provided at the time of submittal. Specific lamp characteristics that should be included in the lamp specification sheet are detailed in Table 3.

灯具包装上注明的灯或带支架的灯具，灯头构造需满足ANSI/IEC标准设计。ANSI

C81.61 &IEC 60061-1中有注明。

灯座设计也要符合ANSI/IEC标准。如：若一个镇流器能启动多功率（如一盏18W, 26W, or 32W的灯泡）的灯泡，那么灯座设计要符合ANSI/IEC标准设计的多功率灯泡。

此外，灯泡规格要满足以下要求：

? ANSI C78.901-2001 and IEC 60901（精致型灯泡）或ANSI C78.81-2001 and IEC 60081 (线型灯泡)定义灯泡规格。

? 若不是按ANSI/IEC灯泡标准设计的特定灯泡，灯泡规格需在交货时一并提供。

Lamp Labeling Requirement 灯标签要求For lamps shipped with fixtures, a manufacturer designation that encompasses the lamp manufacturer name, wattage, correlated color temperature, and color rendering index must be labeled on the lamp or lamp base.

带支架的灯具，灯泡或者灯头的标签上需标有厂商，功率，相关色温和显色指数。

Electronic Ballast Requirements

(Note: Magnetic Ballasts May Not Be Used in Indoor Fixtures): 电子镇流器要求（注：电感镇流器不用于室内灯具）

General 概述Per ANSI C82.11 Section 5 except paragraph 5.3.1. ANSI C82.11第5部分（5.3.1除外）

Lamp Start Time 灯启动时间The time needed after switching on the lamp to start continuously and remain illuminated must be an average of one second or less.

打开灯保持照明平均时间为1或2秒

Power Factor

功率系数

> 0.5 Lamp Current Crest Factor

峰值因数

< 1.7

Maximum Measured Ballast Case Temperature During

Normal Operation Inside

Fixture(s)

正常操作下，镇流箱最高温度Not to exceed the ballast manufacturer maximum recommended ballast case temperature during normal operation inside a fixture.

Note: This performance characteristic is separate and distinct from thermal requirements established by UL, which governs safety rather than longevity of the ballast. All qualified fixtures are expected to meet this requirement, including linear, suspended, close-to-ceiling, IC, ICAT and Non-IC recessed canisters, etc.

as well as those fixtures that may be exempt from UL1598.

不超过厂家规定的最大镇流箱温度值。

注：性能特性同UL热需求不一样，操作安全。所有合格灯具要符合该规格，包括线型，

悬挂型，天花板型,IC,ICAT和非IC嵌入式筒灯等等，还有UL1598豁免的灯具。

Electromagnetic and Radio Frequency Interference

电感和无线电波冲突Ballast must meet FCC requirements for consumer use (FCC 47 CFR Part 18 Consumer Emission Limits)

镇流器必须符合FCC的要求（FCC47CFR 18部分消耗限制）

Ballast Frequency

镇流器频率

20 to 33 kHz 或> 40 kHz

Transient Protection 瞬时保护Per ANSI C82.11b, paragraph 5.10.1 (100kHz Ring Wave, 2.5kV, both common mode and differential mode, 7 strikes)

符合ANSI C82.11b，5.10.1节（100kHz 环形波，2.5kV,有相同和不同模式）

End of Life Protection 灯管末期保护All ballasts that operate lamps sized T5 and smaller must contain an end of life protection circuit. For ballasts that operate multiple lamps and are required to have end of life protection, the ballast must shut down no more than two lamps when one of the lamps has reached end of life. For example, a fixture with one ballast and five lamps must not shut down more than the lamp that has reached end of life plus one additional lamp.

T5灯中的镇流器有末期保护电路。当镇流器启动多盏灯时，当有一盏灯到达一定的使用寿命，为保护电流，镇流器会关闭不超过其中2盏灯。

Dimming 调光Torchiere style portable fixtures shall be dimmable from 100% to 30%, or less, of maximum light output, or be switchable to three levels of brightness, not including the off position.

Other fixture types that utilize dimmable ballasts shall be dimmable from 100% to 30%, or less, of maximum light output, or be switchable to three levels of brightness, not including the off position.

Torchiere轻便式灯具可调光30％－100％，或小于最大电源输出功率，或者转换3挡亮度，闭合处除外。

其他灯具功能同上。

Safety - Ballasts and “Non Edison base Fluorescent Adapters”

安全镇流器和非爱迪生灯头适配器The cover page of a safety test report or a general coverage statement must be provided to demonstrate compliance with ANSI/UL 935 or UL 1993, as appropriate. 安全测试报告首页或概述要注明测试符合ANSI/UL 935 或 UL 1993。

Fixture Requirements 灯具要求

Fixture Warranty 灯具保证A written warranty must be included with fixture packaging at the time of shipment, which covers repair or replacement of defective parts of the fixture housing, optics, trim and electronics (excluding the lamp) for a minimum of two years from the date of purchase.

灯具包装时会附上一份书面保证书，包括灯具外罩、光学器件、装饰物和电子器件（灯泡除外）的保修期（购买之日起最低2年）。

Noise 噪音Class A sound rating for electronic ballasts within the fixture, not to exceed a measured level of 24 dBA (audible) when the ballast is installed in the fixture. 灯具上的电子镇流器噪音水平≤24分贝。

Lamp Shipment Requirement 灯具出货要求All indoor fixtures must be shipped with a lamp, except for the following fixture types:

1. Recessed downlight fixtures and recessed downlight retrofit kits

2. Fixtures using linear fluorescent lamps

所有灯具出货时要配灯泡，以下种类除外：

1. 嵌入式筒灯和筒灯架

2. 使用线型荧光灯的灯具

Replaceable ballast 可替代式镇流器Ballasts in all fixtures (including portables) must be accessible and removable by an electrician without the cutting of wires and without damage to the fixture housing, trim, decorative elements or the carpentry (e.g., ceiling drywall) to which the fixture is attached.

灯具镇流器（包括轻便型）要安装简易，无须电工切线，灯外罩、装饰器件、或墙面不受损坏。

Safety - Portable Fixtures 安全－轻便式灯架The cover page of a safety test report or a general coverage statement must be provided to demonstrate compliance with ANSI/UL 153 ANSI/UL 153.

安全测试报告的封面或总概述必须注明符合ANSI/UL 153 ANSI/UL 153。

Safety - Hardwired Fixtures 安全－硬连线灯具The cover page of a safety test report or a general coverage statement must be provided to demonstrate compliance with UL 1598.

安全测试报告的封面或总概述必须注明符合UL 1598.。

Recessed Downlight Fixtures- Insulation Contact (IC)-Rated 嵌入式筒灯灯具－绝缘触层－额定Recessed downlight fixtures that are either IC-Rated for direct contact with insulation or non IC-Rated may qualify as ENERGY STAR. For fixtures to be considered IC-Rated they must be approved for zero clearance insulation cover (IC) by an OSHA NRTL laboratory. Recessed downlight fixtures that are IC-Rated must also meet the requirements for air tight fixtures, listed below.

嵌入式筒灯灯具要么是额定绝缘IC触层或符合能源之星的非绝缘触层。灯架应是无间隙的额定绝缘触层（OSHA NRTL实验室认可）。嵌入式筒灯也应符合额定绝缘触层气密装置的要求。

Recessed Downlight

Fixtures-Air Tight For

Restricted Air Movement 嵌入式筒灯－气密型Recessed downlight fixtures that are either air tight or not air tight may qualify as ENERGY STAR. For fixtures to be considered air tight, the housing or

certified/listed accessory must have leakage less than 2.0 cubic feet per

minutr(CFM) at 75 Pascals (or 1.57 lbs/ft

2

) when tested in accordance with ASTM

E283 and shall be sealed with a gasket or caulk.

For recessed downlight fixtures that are air tight, the following measures must be taken to ensure that fixtures can be properly installed and inspected:

1. Product packaging must meet the requirements set forth in the “Product Packaging for Consumer Awareness Requirements” section below.

2. The fixture itself must include a label certifying “air tight”, or similar designation, to show air leakage less than 2.0 CFM at 75 Pascals when tested in accordance with ASTM E28

3. The label must be clearly visible to a building inspector.

3. Installation instructions must be included listing all components of the assembly that will be necessary to ensure an airtight installation and how the components should be properly installed. For example, depending on the method used to achieve air-tight operation, the instructions should alternatively show how a gasket is to be attached, what type of caulk to use and how it should be applied, or which certified airtight trim kits are designed to be installed with the luminaire housing.

嵌入式筒灯应是符合能源之星的气密型或非气密型。灯具也应是气密型，外罩或灯配件要粘上垫片或敛铆缝，漏泄量≤2.0立法英尺/分钟，压强75帕斯卡（或1.57 lbs/ft

2

），符合ASTM E283测试标准。

嵌入式筒灯是气密型，安装和检测要求如下：

1. 产品包装要“消费者要求”

2. 灯具标签要注明类似于“气密”，标明符合ASTM E283标准的漏泄量≤2.0立法英

尺/分钟，压强75帕斯卡（或1.57 lbs/ft

2

）。标签要看得见。

3. 为确保气密安装到位，安装说明要列出所有零件。如，要介绍垫片是如何粘的？

敛铆缝如何使用？或灯具外罩应配装怎样的气密装置等？

Product Packaging for

Consumer Awareness

Requirements

符合消费者要求的产品包装For fixtures that are not shipped with lamps, product packaging must include a list of lamps types that would ensure ENERGY STAR quality and performance when paired with the qualifying fixture. This list must be clearly visible to the consumer on the fixture packaging.

Manufacturers are not required to provide specific lamp manufacturer names and model numbers on the packaging. Rather, generic lamp listings, such as the NEMA or ANSI generic descriptions including a color designation (e.g., F32T8/830 or CFQ26W/G24q/827), will suffice. In addition, packaging should suggest that consumers select a lamp with a rated life of 10,000 hours or more. Note:only recessed downlight fixtures, recessed downlight retrofit kits, and fixtures using linear lamps may ship without a lamp.

For fixtures that are shipped with lamps, product packaging language is required that clearly describes the nominal color designation of the lamp in units of Kelvin (i.e., 2700K, 3000K, 3500K, 4100K, 5000K, or 6500K).

For recessed downlight fixtures that are IC-Rated, product packaging must clearly state this rating. The language must be clearly visible on the product packaging. The IC-Rated designation will also be included in the fixture description included in the Qualified Product list posted on the ENERGY STAR Web site. Sample language: “IC-Rated for direct contact with insulation”.

For recessed downlight fixtures that are Air-Tight (AT) rated, product packaging must clearly show that the fixture produces less air leakage than 2.0 CFM at 75 Pascals when tested in accordance with ASTM E283. The language must be clearly visible on the product packaging. The “air tight”, or similar, designation will also be included in the fixture description included in the Qualified Product list posted on the ENERGY STAR Web site. Sample language: “Certified Air Tight per ASTM E283.”

未带灯泡的灯具，要在产品包装上列出与之配套的能源之星规格的灯泡类型和性能。灯具厂家只需列出一般类型的灯泡即可，如NEMA 或 ANSI描述，包括灯泡颜色（如F32T8/830 或 CFQ26W/G24q/827）。另还需注明等使用寿命为10，000小时等。注：唯独嵌入式筒灯，嵌入式筒灯架和线型灯具可不带灯泡。

对于带灯泡的灯具，包装上要注明相关色温（如2700K, 3000K, 3500K, 4100K, 5000K, or 6500K）.

绝缘触头的嵌入式筒灯灯具包装上要注明额定值。并注能源之星合格产品单的网址。例句“IC-Rated for direct contact with insulation”.（额定绝缘触头）

气密型（AT）嵌入式筒灯灯具的包装要注明气密漏泄量≤2.0立法英尺/分钟，压强75帕斯卡（或1.57 lbs/ft

2

），符合ASTM E283测试标准；还要注明类似于“气密”的描述，并注明并注能源之星合格产品单的网址。例句：“Certified Air Tight per ASTM

E283.”

（认证的ASTM E 283气密型）

1

Efficacy shall be determined by the following equation:

以下方程式计算功效：

Efficacy [Lumens per Watt] = Measured Lamp Lumens [Lumens]

Measured Input Power [Watts]

功效【流明/瓦】= 灯光通量 [Lumens] 流明

输入功率 [Watts] 瓦

Lamp Lumens: Lamp lumens must be measured using the lamp and ballast that are shipped with the fixture. 光通量（流明）：对带灯泡和镇流器的灯具进行测量。

Input Power: Input power must be measured with the lamp and ballast that are shipped with the fixture.

输入功率：对带灯泡和镇流器的灯具进行测量。

Table 1A – Additional Requirements for Indoor Recessed Downlight Retrofit Kits 表1A－室内嵌入式筒灯支架的额外要求

Performance

Characteristic

ENERGY STAR Specification

Characteristic

特性

能源之星规格

Note: The following ENERGY STAR performance requirements must be met by recessed downlight retrofit kits in addition to those listed in Table 1 – Indoor Fixtures, above.

注：下述能源之星的性能要符合嵌入式筒灯支架规格，表1所列（室内灯具）除外。

Reflectors 反射罩Reflectors must be included to maximize fixture efficiency. 反射罩要列入最高灯具功效。

Aperture 空尺寸Maximum 7.0” ≤7.0”

Air Tight For Restricted Air Movement

限制气密的要求Only recessed downlight retrofit kits that are air tight may qualify as ENERGY STAR. For fixtures to be considered air tight, the housing or certified/listed accessory must have leakage less than 2.0 cubic feet per minute (CFM) at 75 Pascals (or 1.57 lbs/ft

2

) when tested in accordance with ASTM E283 and shall be sealed with a gasket or caulk.

For recessed downlight retrofit fixtures, the following measures must be taken to ensure that fixtures can be properly installed and inspected:

1. Product packaging must meet the requirements set forth in the “Product Packaging for Consumer Awareness” section within this table, below.

2. The fixture itself must include a label certifying airtight or similar designation to show air leakage less than 2.0 CFM at 75 Pascals when tested in accordance with ASTM

E283. The label must be clearly visible to a building inspector.

3. Installation instructions must be included listing all components of the assembly that will be necessary to ensure an airtight installation and how the components should be properly installed. For example, depending on the method used to achieve air-tight operation, the instructions should alternatively show how a gasket is to be attached, what type of caulk to use and how it should be applied, or which certified airtight trim kits are designed to be installed with the luminaire housing.

仅仅嵌入式筒灯支架应是符合能源之星的气密型。灯具是气密型，外罩或灯配件要粘上垫片或敛铆缝，气密漏泄量≤2.0立法英尺/分钟(CFM)，压强75帕斯卡（或1.57 lbs/ft

2

），符合ASTM E283测试标准。

嵌入式筒灯是气密型，安装和检测要求如下：

1. 产品包装要“消费者要求”

2. 灯具标签要注明“气密”或类似于“气密”，标明符合ASTM E283标准的气密漏泄量≤2.0

立法英尺/分钟(CFM)，压强75帕斯卡（或1.57 lbs/ft

2

）。标签要帖明显。

3. 为确保气密安装到位，安装说明上要列出所有零件。如，要介绍垫片是如何粘的？敛铆缝

如何使用？或灯具外罩上应配装怎样的气密装置等？

Electrical Connections 电气连接Edison lamp socket with wire “pigtail” to the ballast. 带连接镇流器短花线圈（pigtail）的爱迪生灯泡插座

Safety - Fixture Conversions, Retrofits 安全－灯具

自由转换Fixtures must be tested and listed by an OSHA NRTL laboratory as acceptable for compliance with NFPA 70, National Electrical Code (NEC).

The cover page of a safety test report or a general coverage statement must be provided to demonstrate compliance with UL 1598 and UL 1598B.

灯具测试需由OSHA NRTL(美国国家认可实验室)出具，并符合NFPA 70（国家电工标准代码NEC）的标准。

测试报告封面上要注明该安全测试符合UL 1598 &UL 1598B.

Product Packaging for Consumer Awareness Requirements

消费者认可的包装规格Recessed downlight retrofit kit packaging and instructions must clearly indicate:

1. What fixture model numbers the recessed downlight retrofit kits are compatible with.

2. Whether or not the product is dimmable. If dimmable, user instructions must clearly indicate what type of dimming circuit it can be used on.

3. Any known incompatibility with photo controls, dimmers or timing devices.

4. Airtight or similar designation to show air leakage less than 2.0 CFM at 75 Pascals when tested in accordance with ASTM E283. The language must be clearly visible on the product packaging. The “air tight”, or similar, designation will also be included in the fixture description included in the Qualified Product list posted on the ENERGY STAR Web site. Sample language: “Certified Air Tight per ASTM E283.”

嵌入式筒灯支架包装&说明书要求如下：

1. 注明嵌入式筒灯支架适配的灯具型号。

2. 若该产品是可可调光的，使用说明书上要注明调光电路。

3. 注明不适配的图片控制器，调光器或调速器类型。

4. 灯具标签要注明“气密”或类似于“气密”类型，标明符合ASTM E283标准

的气密漏泄量≤2.0立法英尺/分钟(CFM)，压强75帕斯卡（或1.57 lbs/ft

2

）。

标签要帖得明显。并附上能源之星合格产品目录的网址。例句：“Certified Air

Tight per ASTM E283.”（气密经ASTM E283认证）

Table 2A – Outdoor Fixtures: Compliance Through Efficient Light Source

表2A——户外产品：通过有效灯具源来达到要求

Performance Characteristic

性能特征

ENERGY STAR Specification ENERGY STAR规定

Note: Only electronic ballasts may be used to meet the requirements of this table with the exception of high intensity discharge lamps, such as metal halide or high pressure sodium lamps. In these cases magnetic ballasts can still be used. In addition, fixtures that utilize compact fluorescent lamps that do not have a plug-in base (i.e use a mogul, medium, or other screw base) are not eligible to earn the ENERGY STAR. For example, a screw-based compact fluorescent lamp may not be used, though a metal halide lamp may be used.

注：只有电子镇流器可用于达到本表的要求，不包括如金属卤化或高压钠灯等高发光强度灯具。在这些情况下仍可使用磁性镇流器。另外，使用紧凑荧光灯的产品，但没有插入底（即使用mogul基座、中型头和其它的螺旋底），不能得到ENERGY STAR的认证。例如，一个螺旋底的紧凑型荧光灯不可以使用，但一个金属卤化灯可以使用。

Combined Lamp & Ballast Requirements:

带镇流器灯的规定

System Efficacy Per Lamp Ballast Platform in Lumens Per Watt (LPW)

以每瓦特流明量计算每个灯具镇流器体系的功效>40 LPW for all lamp types below 15 total listed lamp watts.

> 50 LPW for all lamp types over 15 total listed lamp watts up to 30 total listed lamp watts

>60 LPW for all lamp types over 30 total listed lamp watts

> 40 LPW，所有灯具总瓦特数低于15时。

> 50 LPW，所有灯具总瓦特数大于15，少于30时

> 60 LPW，所有灯具总瓦特数大于30时

Lamp Requirements:灯规定

Lamp Life 灯具寿命

For lamps shipped with the fixtures, the average rated life of the lamp must be >10,000 hours.

对于与产品一起出售的灯具，其使用寿命必须大于10,000小时。

If the lamp is not shipped with the fixture, product packaging must meet the requirements set forth in the “Product Packaging for Consumer Awareness” section of this Table.

如果灯具不同产品一起出售，包装必须满足本表“消费者认可的产品包装”中的要求。

Lamp/Lampholder Compatibility

灯/灯座的兼容性

For lamps indicated on the fixture packaging or shipped with the fixtures, lamps must utilize an ANSI/IEC standardized lamp base configuration, as defined by ANSI C81.61 and IEC 60061-1.

对包装上注明的灯具或与产品一起出售的灯具，根据ANSI C81.61和IEC 60061-1的定义，灯具必须使用NSI/IEC标准灯座结构。

The lampholder must be designed to accept lamps with ANSI/IEC standardized lamp base configurations for all applicable wattages. For example, if the ballast can operate lamps with multiple wattages (e.g., an 18W, 26W, or 32W lamp) then the lampholder must be designed to accept lamps with ANSI/IEC standardized lamp base configurations for all three applicable wattages.

灯座必须设计为ANSI/IEC标准灯座结构，可使用所有适用瓦特数的灯具。例如，如果镇流器可以控制多种瓦特数的灯具（例如18W、 26W或32W灯具），灯座则必须设计为ANSI/IEC标准灯座结构以适用三种瓦特数的灯具。

In addition, lamps shall either:

? Meet the requirements of an ANSI/IEC standardized lamp specification sheet,

as defined by ANSI C78.901-2001 and IEC 60901 (for compact fluorescent lamps) or ANSI C78.81-2001 and IEC 60081 (for linear lamps) if an applicable standard exists, or, ? If no ANSI-IEC lamp standard exists (e.g., a spiral compact fluorescent lamp), a custom lamp specification sheet must be provided at the time of submittal. Specific lamp and lamp base characteristics that should be included in the lamp specification sheet are detailed in Table 3.

另外，灯具应满足以下两个条件之一：

如有可行的标准，根据ANSI C78.901-2001和IEC 60901 (适用于紧凑型荧光灯)或ANSI C78.81-2001和IEC 60081（适用于线型灯），满足 ANSI/IEC标准灯具规格表的要求，或如果没有ANSI-IEC标准（如螺旋型紧凑荧光灯），须提交一份特定的灯具规格表。该表须包括表3所述的灯具和灯座特点。

Ballast Requirements:镇流器要求

Electromagnetic and Radio Frequency Interference

电磁和无线电波冲突

Ballast must be FCC rated for consumer use (FCC 47 CFR Part 18 Consumer Emission Limits).

镇流器必须按FCC规定的作消耗装置使用(FCC 47 CFR ,第18部分，消耗发散限制)。

End of Life (EOL) Protection 末期维护All ballasts that operate lamps sized T5 and smaller must contain an end of life protection circuit, per ANSI/IEC requirements. For ballasts that operate multiple lamps and are required to have end of life protection, the ballast must shut down no more than two lamps when one of the lamps has reached end of life. For example, a fixture with one ballast and five lamps must not shut down more than the lamp that has reached end of life plus one additional lamp.

所有控制T5或更小的灯具的镇流器，必须根据ANSI/IEC要求带末期保护电路。对于控制多个灯具的镇流器须有终端寿命控制电路，当一个灯具达到寿命期限时，镇流器关闭的灯不得超过两个。例如，一个配5个灯具的镇流器，关闭灯具的数量不得超过达到寿命期限的灯加上另一个灯具的数量的和。

Fixture Requirements:产品要求

Maximum Input Power

最大输入功率

150 watts

Automatic Daylight Shutoff 自动日光关闭

The fixture must contain an integrated photosensor that

automatically prevents operation during daylight hours. In addition, the control must automatically reactivate within 24 hours of a manual override or testing operation.

产品必须包括一个完整的光敏元件自动禁止白天运作。另外，人工控制或测试须24小时内自动转换回正常模式。

Fixture Warranty 产品保修

A written warranty must be included with fixture packaging at shipment, which covers repair or replacement of defective parts of the fixture housing or electronics (excluding the lamp) for a minimum of two years from the date of purchase.

出售的产品包装中必须包括一份保修书，保证产品外罩或电子元件（不包括灯具）的失效部件可以替换或至少两年保修。

Replaceable ballast 可替代镇流器Ballasts must be accessible to and removable by an electrician without the cutting of wires and without damage to the fixture housing, trim, decorative elements or the carpentry (e.g. ceiling drywall) to which the fixture is attached.

如果产品内有镇流器，在无需剪断电线、不损坏外罩、边、装饰部分和产品附属的木材材料（例如天花板墙壁）情况下，电工可操作自如。。

Safety 安全

Fixtures must be compliant with NFPA 70, the National Electrical Code

(NEC), including requirements for wet or damp locations (Articles 410-4a and Article 100).

产品必须符合NFPA 70、国家电气编码（NEC），包括潮湿场所（410-1a项和100项）

Product Packaging for Consumer Awareness Requirements

消费者认可的产品包装

For fixtures that are not shipped with lamps, product packaging must include a list of lamp types that would provide ENERGY STAR quality and performance when paired with the qualifying fixtures. This list must be clearly visible to the consumer on the fixture packaging.

对于不带灯具的产品，产品包装必须注明可以与该产品配套使用的与ENERGY STAR(能源之星)相同质量和性能的灯具类型。包装上的清单必须清晰。

Manufacturers are not required to provide specific lamp manufacturer names and model numbers on the packaging. Rather, generic lamp listings, such as the NEMA or ANSI generic descriptions including a color designation (e.g., F32T8/830 or

CFQ26W/G24q/827), will suffice. In addition, consumers should be directed to select a lamp with a rated life of 10,000 hours or more.

厂商在包装上无需注明灯具制造商的名称和型号。但是，普通的灯具清单，例如NEMA 或ANSI普通描述，包括颜色名称（例如F32T8/830或CFQ26W/G24q/827）就足够了。另外消费者可选择一个设计寿命为10，000小时或以上的灯具。

Product packaging must indicate the minimum (lowest) starting temperature for the lamp and ballast platform of the fixture.

产品标准必须标明灯具和镇流器系统的最低启动温度。

If the automatic daylight shutoff control can be adjusted such that the fixture can operate during full daylight, or automatic reactivation will not occur within 24 hours of a manual override or testing operation, additional packaging language is required that provides a range of settings that will result in the fixture complying with the specification. The language must be clearly visible to the consumer on the fixture packaging and in the fixture manual. Sample language: “To meet ENERGY STAR requirements the photosensor control knob must be set to x, y, or z to prevent operation during full daylight.”

如果自动日光遮断装置能调整到产品可以在日光中操作，或在人工操作/测试操作的情况下24小时内不会重新自动遮断，产品包装须表明使得产品符合该描述的系列设置。产品包装和手册上的文字须清晰。包装文字范例：“为了达到ENERGY STAR的要求，光敏元件控制须调到x、y或z以避免在日光条件下操作”。

Table 2B - Outdoor Fixtures: Compliance Through Reduced Operating Time

表2B——户外产品：通过减少操作时间达到要求。

Performance

Characteristic

ENERGY STAR Specification ENERGY STAR说明

Characteristic

功能特征

Note: All lamp types (fluorescent, incandescent, etc.) may be used to meet the requirements set forth in this table.

注：可能使用所有类型的灯具（荧光灯、白炽灯等）以达到本表格的要求。

Fixture Requirements:

Maximum Input Power

最大输入功率

250 watts

Automatic Daylight Shutoff

自动日光遮断

The fixture must contain an integrated photosensor that automatically prevents operation during daylight hours. In addition, the control must automatically reactivate within 24 hours of a manual override or testing operation.

产品必须包括一个完整的光敏元件禁止白天运作。人工控制或测试24小时内可以自动转换回正常模式。

Motion Control 移动控制

The fixture must contain an integrated motion sensor that employs infrared sensing technology.

The sensor must:

? allow automatic shut-off of the lamp within 15 minutes of being manually activated by a switch or automatically activated by the sensor, and

? automatically reset to sensing mode within 24 hours of a manual override or testing operation.

产品必须包括一个包含红外感应技术的移动传感器。该传感器必须：

? 手动通过开关激活或传感器自动激活后，15分钟之内可以自动关闭灯具。

? 人工控制或测试24小时内可以自动的转换为传感模式。

The fixture must:

? have an indicator that visibly or audibly informs the device operator that the motion sensor is operating properly, or that it has failed or malfunctioned.

产品必须：

?须有可看见或听见的指示器表明移动传感器运作正常、失效或存在故障。

Fixture Warranty 产品保修

A written warranty must be included with fixture packaging at shipment, which covers repair or replacement of defective parts of the fixture housing or electronics (excluding the lamp) for a minimum of two years from the date of purchase.

出售产品包装中必须包括一份保修书，保证产品机架或电子元件（不包括灯具）的失效部件可以替换或至少两年保修。

Replaceable ballast 可替换镇流器

If a ballast is present in the fixture, it must be accessible to and removable by an electrician without the cutting of wires and without damage to the fixture housing, trim, decorative elements or the carpentry (e.g., ceiling drywall) to which the fixture is attached.

如果产品内有镇流器，在无需剪断电线、不损坏外罩、边、装饰部分和产品附属的木材材料（例如天花板墙壁）情况下，电工可操作自如。

Safety 安全Fixtures must be compliant with NFPA 70, the National Electrical Code

(NEC), including requirements for wet or damp locations (Articles

410-4a and Article 100).

产品必须符合NFPA 70、国家电气编码（NEC），包括潮湿场所（410-1a项和100项）

Product Packaging for Consumer Awareness Requirements

消费者认可的产品包装If the automatic daylight shutoff control can be adjusted such that the fixture can operate during full daylight, or automatic reactivation will not occur within 24 hours of a manual override or testing operation, product packaging language is required that provides a range of settings that will result in the fixture complying with the specification. The language must be clearly visible to the consumer on the fixture packaging and in the fixture manual. Sample language: “To meet ENERGY STAR requirements the photosensor control knob must be set to x, y, or z to prevent operation during full daylight.”

如果自动日光遮断装置能调整到产品可以在日光中操作，或在人工操作/测试操作的情况下24小时内不会重新自动遮断，产品包装须表明使得产品符合该描述的系列设置。产品包装和手册上的文字须清晰。包装文字范例：“为了达到ENERGY STAR（能源之星）的要求，光敏元件控制须调到x、y或z以避免在日光条件下操作”。

If the integrated motion sensor can be adjusted such that shut-off will not occur within 15 minutes or automatic reset to sensing mode will not occur within 24 hours of a manual override or testing operation, product packaging must provide a range of settings that will resulting the fixture complying with the specification. The language must be clearly visible to the consumer on the fixture packaging and in the fixture manual. Sample language: “To meet ENERGY STAR requirements, the motion sensor control knob must be set to x, y, or z to allow automatic reset of the sensor”. In addition, the fixture must include instructions within the packaging that outlines step-by-step calibration instructions for the motion sensor.

如果整个传感器可以调整到15分钟内自动遮断不会发生，在24小时内的人工操作或测试操作中不会自动重新设置到传感模式，产品包装须表明使得产品符合该描述的系列设置。产品包装和手册上的文字须清晰。包装文字范例：“为了达到ENERGY STAR的要求，传感器须调到x、y 或z以允许自动重新设置”。另外，产品包装内须有分步描述如何调节传感器的说明。

4) Qualification Process, Acceptable Sources of Documentation, Reference Standards & Required Documentation:

The following section describes the steps required to qualify residential light fixtures as ENERGY STAR, provides information about acceptable sources of documentation, and states the testing standards and documentation required for each performance characteristic.

认证程序、认可的文件内容、参考标准&需要的文件：

以下章节描述家用灯具产品如何达到ENERGY STAR标准，并提供关于认可的文件内容信息，陈述每个性能特征的测试标准和所需的文件。

Qualification Process: 认证程序

To qualify a residential lighting fixture as ENERGY STAR, it must be tested according to the protocol outlined below.

Note: EPA reserves the right to require additional documentation, at any time, in order to determine

compliance with all performance characteristics.

家用灯具符合ENERGY STAR标准，需通过以下条款规定的测试。注：EPA保留在任何时候所取另外的文件，以保证符合所有的性能特征。

A. Partner must test qualifying products and obtain required documentation to meet the performance characteristics

listed in Section 3 of this specification. Refer to Table 3, below, to determine the reference standard and

required documentation applicable to each performance characteristic.

合约方必须测试产品并获得文件以满足第三部分列出的性能特征。参考表3以确认每项性能特征所需的参考标准和文件。

The following stipulations apply:

以下条款适用;

? For multiple fixture models that use the same lamp/ballast combination, only one set of test results is

required. For example, two fixtures that use the same lamp and ballast combination, but have different

trim, lens and/or chasse need only be tested once.

对于使用相同灯具/镇流器组合的产品，只需要一个测试结果。例如：两个使用同样的灯具和镇流器组合，但有不同的修饰、

透镜等只需要测试一次。

? For fixture models that may use different ballasts (either in terms of the type of ballast or manufacturer), each lamp/ballast combination must undergo testing and the test results must be submitted for

qualification. For example, if a residential light fixture partner plans to use ballasts from several

manufacturers in any one fixture, the fixture must be tested with each manufacturer’s ballast.

对使用不同镇流器的产品（不同的镇流器类型或制造商），每款灯具或镇流器都必须经过测试，测试结果须提交作认证之用。

例如，如果一个家用灯具的厂商想将几种不同厂商生产的镇流器用于一个产品上，产品必须配合每个制造商的镇流器进行测

试。

? For fixture models with one ballast type that can work with multiple lamp types, the fixtures need only be tested with one lamp type. The lamp type must either be the one supplied with the fixture at shipment or, if

a lamp is not supplied, one of the lamp types listed on the packaging. Please note that EPA expects all

lamps listed on the packaging to comply with the specification when operating on the fixture’s ballast. To

ease the burden on the manufacturer, however, test data need be submitted for only one lamp type

operating on the fixture’s ballast.

对于一种镇流器可以与多种灯具配合工作的产品，该产品只需与一种灯具配合进行测试。灯具类型须是与产品一起提供的或

如果没有提供灯具，包装上标明的灯具类型。请知悉EPA希望所有写于包装上的灯具都能与产品的镇流器配合使用。但是，

为了减轻制造商的负担，只需提供一种灯具与产品镇流器配合使用的测试数据。

B. Submit a completed and signed copy of the ENERGY STAR Residential Light Fixture Qualified

Product Information (QPI) form, along with required documentation, to the address listed on the QPI form. To

obtain the current version of the QPI form, visit the “Lighting” section of the ENERGY STAR Web site at

https://www.360docs.net/doc/b75925531.html,/partners and click on “Product Specifications.”

提交一份完整并签字的“ENERGY STAR灯具产品合格产品信息（QPI）”表，连同其它所需文件，发到QPI表上的地址。

想取得最新的QPI表，到ENERGY STAR网址(https://www.360docs.net/doc/b75925531.html,/partners)的“Lighting”中，并点击“Product Specifications”。

Acceptable Sources of Documentation:

A. A variety of acceptable sources of documentation are referenced for each performance characteristic within

Table 3. For clarity, these sources are summarized below:

接受的文件来源：

A. 多数接受的文件来源与表3内的每项功能特性有关。

为了更清楚，现总结如下：

A test report from a laboratory accredited by NVLAP or one of its MRA signatories – Both public and

private accredited laboratories may be used. NVLAP’s MRA signatory partners include ILAC, APLAC, and

NACLA. Note that if the laboratory used for the lumen output, CRI, CCT, or lamp life test is accredited by

NVLAP or one of its MRA signatories, it must also have a scope of accreditation that includes the method of

measurement reference standard for this performance characteristic. Partners should obtain from the

laboratory both its certificate of accreditation and its scope of accreditation and submit them to ENERGY

STAR.

由NVLAP指定的实验室或其MRA合约方的测试报告——政府或私有指定的实验室都可以。NVLAP的 MRA合约方包括

ILAC、APLAC和NACLA。请注意对流明输出、CRI、CCT或灯具寿命进行测试的实验室是由NVLAP或某个MRA合约方指定，

委派范围必须包括性能特征的测量参考标准方法。合约方应从实验室取得委派证明和委派范围，并提交给ENERGY STAR。

An EPA-approved Platform Letter of Qualification – These letters are provided from EPA to manufacturers who have pre-approved specific performance characteristics for their lamp and/or ballast. When using this

type of documentation, Partners should obtain a copy of the applicable letter from the manufacturer and

include it with the ENERGY STAR submittal.

一份EPA批准的体系资格证书——该证书是EPA授予那些已经提前为灯具和/或镇流器的性能特征取得批准的制造商。当使

用改类文件时，合约方应从制造商取得该证书，并一起和其它材料提交给EPA.

EPA-approved documentation from an industry association – In certain instances, EPA has approved documentation from industry associations who take responsibility for specific performance characteristics of

lamps and/or ballasts. When using this type of documentation, Partners should contact the industry

association to obtain the EPA-approved documentation that is required for use with ENERGY STAR

submittals. Note: Partners may use the NEMA-ALA Lamp and Ballast Matrices as a source for obtaining

required information to qualify fixtures. These matrices can be found at

https://www.360docs.net/doc/b75925531.html,/lampballastmatrix/ .

从工业组织获得EPA批准的文件——在一些情况下，EPA批准一些负责灯具和/或镇流器性能特征的工业组织的文件。当使用这类文件时，合约方需要联系相关的工业组织以取得EPA批准的文件，并与其它要求的文件一起提交给ENERGY STAR。注：合约方可以参考“NEMA-ALA灯具和镇流器模块”中的信息，以获得认证所需的材料。信息可以在

https://www.360docs.net/doc/b75925531.html,/lampballastmatrix/ .找到。

A test report from an OSHA NRTL laboratory – Documentation for safety requirements must come from an

OSHA NRTL laboratory. OSHA NRTL laboratories may also be used to obtain certain additional

performance characteristics, as specified in Table 3.

OSHA NRTL实验室的测试报告——安全要求文件必须来自OSHA NRTL实验室。如表3所述，也可以从OSHA NRTL实验室取得一些额外的性能特征。

Manufacturer documentation – Documentation for certain performance characteristics (such as product packaging requirements) may come directly from the original equipment manufacturer.

厂商文件——某些性能特征的文件（例如产品包装要求）可以直接由产品制造商提供。

B. The information below may be used to locate an accredited testing facility:

以下信息用于寻找指定的测试机构。

For a list of NVLAP accredited laboratories, visit the NVLAP Web site at https://www.360docs.net/doc/b75925531.html,/nvlap or call

(301) 975-4016.

NVLAP指定的实验室，到NVLAP网站https://www.360docs.net/doc/b75925531.html,/nvlap或电话(301) 975-4016。

For a list of signatories to the ILAC MRA, visit the ILAC Web site at https://www.360docs.net/doc/b75925531.html,

ILAC MRA合约方的清单，到 ILAC网站https://www.360docs.net/doc/b75925531.html,

For a list of signatories to the APLAC MRA, visit the APLAC Web site at https://www.360docs.net/doc/b75925531.html,/aplac/ .

APLAC MRA合约方的清单，到APLAC网站https://www.360docs.net/doc/b75925531.html,/aplac/ .

For a list of signatories to the NACLA MRA, visit the NACLA Web site at https://www.360docs.net/doc/b75925531.html, .

NACLA MRA合约方的清单，到NACLA网站https://www.360docs.net/doc/b75925531.html, .

For a list of accredited OSHA NRTL laboratories, visit https://www.360docs.net/doc/b75925531.html,/dts/otpca/nrtl/ or call (202)

693-2110.

指定的OSHA NRTL实验室，到https://www.360docs.net/doc/b75925531.html,/dts/otpca/nrtl/ 或电话 (202) 693-2110

Reference Standards & Required Documentation: 参考标准和所需文档

Table 3 – Reference Standards and Required Documentation

表3——参考标准和所需文档

Performance Characteristic

(refer to Tables 1, 1A, 2A or 2B as appropriate)

性能特征（与表1, 1A, 2A or 2B合适的内容相关）Methods of Measurement Reference

Standards

测量参考标准方法

Required Documentation

(to be attached to QPI Form)

所需文件

以QPI形式的

System Efficacy: Lamp Lumens

Input Power (Tables 1, 2A)

灯具流明

输入功率

（表1，2A）IESNA LM-9; LM-66;

ANSI C82.2

Laboratory test results must be

produced using the specific lamp and

ballast combination that will operate in

the fixture. For this test, a sample of

three or more lamps must be used.

Two of the three samples must pass in

order to qualify for ENERGY STAR.

用在产品中使用的灯具和镇流器来制作

实验室测试报告。本测试使用三个或三个

以上的样品。为了使质量符合ENERGY

STAR要求，所选的三个样品必须有两个

通过测试。

Provide: 提供

1. a test report from a

laboratory accredited by NVLAP or one

of its MRA signatories; or

由NVLAP指定的实验室或其

MRA合约方的测试报告；或

2. an EPA approved Platform

Letter of Qualification that lists the

lamp/ballast combination used in the

fixture and the test result for this

performance characteristic; or

一份EPA批准的体系资格证书，

该证书列出产品中灯具/镇流器组合及其

性能特征；或

3.

EPA-approved

documentation from an industry

association, such as the NEMA/ALA

matrices.

从工业组织，如NEMA/ALA

matrices获得EPA批准的文件；或

Note: If the laboratory used for this test

is accredited by NVLAP or one of its

MRA signatories it must also have a

scope of accreditation that includes the

method of measurement reference

standard for this performance

characteristic.

如果进行该测试的实验室是NVLAP指定

的或其MRA合约方，委派范围必须包括

性能特征的测量参考标准方法。

Reflectors (Table 1A) 反射面（表 1A）No Standard Available

(Use manufacturer protocol) 无标准（使

用厂商协议）

No supplemental documentation

required.无需补充文件。

Lamp Start Time 灯具启动时间(Table 1A) （表1）ANSI C82.11-5.2 Laboratory test results must be

produced using the specific lamp and

ballast combination that will operate in

the fixture. For this test, a sample of

three or more lamps must be used.

Two of the three samples must pass in

order to qualify for ENERGY STAR.

用在产品中使用的灯具和镇流器来制作

实验室测试报告。本测试使用三个或三个

以上的样品。为了使质量符合ENERGY

STAR要求，所选的三个样品必须有两个

通过测试。

Provide: 提供

1. a test report from a

laboratory accredited by NVLAP or one

of its MRA signatories; or

由NVLAP指定的实验室或其

MRA合约方的测试报告；或

2. an EPA approved Platform

Letter of Qualification that lists the

lamp/ballast combination used in the

fixture and the test result for this

performance characteristic; or

一份EPA批准的体系资格证书，

该证书列出产品中灯具/镇流器组合及其

性能特征；或

3.

EPA-approved

documentation from an industry

association, such as the NEMA/ALA

matrices; or

从工业组织，如NEMA/ALA

matrices获得EPA批准的文件；或

4. a test report from an OSHA

NRTL laboratory.

从OSHA NRTL实验室取得的

测试报告。