手机BB硬件测试验收标准_V0.1_2011.7.18

Return to Cover

VbatMin = 3.45V VbatNom = 3.8V VbatMax = 4.2V

No.

Test Name

Test Description

Acceptance Criterias

Qty.

Not Apply Issue

Grid

Result Report

Failed Item Description

Action Plan

BB1.1

手机重要功能测试

(Handset all-important Function Test)①下载(Downloading)②开机(Switch on)

③读写SIM 卡(Read Write SIM Card)功能正常(Function should be OK)2

On Going

BB1.1.1下载(Downloading)

●电池电压为Vbatnom(Vbat=VbatNom)●使用下载工具下载(Download by DL tool)

下载正常(No problem about downloading)2

NA

BB1.1.2开机(Handset switch-on)

●将电源调到VbatMin 和VbatMax ，分别开机(Turn ON at Vbatmin and Vbatmax)

●装入SIM 卡，不装SIM 卡，分别开机( With and without Sim- card)

手机开机正常

(Handset must switch-on correctly)

2NA

BB1.1.3

读写SIM 卡(Read / write with SIM card)对SIM 卡进行读写操作

(To check the Sim <-> handset link at reading and writing a repertory name)SIM 卡读写正常

(Read and write without problem)

2NA

BB1.1.4

耳机检测(Headset Detection)●在待机模式下，插入/拔出耳机(In idle mode, headset plug in/out)●在通话模式下，插入耳机

(In communication mode, headset plug in/out)耳机插入/拔出识别正常

(Headset plug in/out detection was OK)

2NA

[特别检查通话模式下，耳机多次插拔是否会误挂电话或着不识别耳机]

BB1.1.5

充电器检测(Charger Detection)●在待机模式下，插入充电器(In idle mode, insert charger)●在关机模式下，插入充电器(In OFF mode, insert charger)●在通话模式下，插入充电器

(In communication mode, insert charger)

充电器识别正常

(Charger detection OK)

2NA

BB1.2

重要电压及漏电流测试

(Important power output

voltage & Leakage Current

Test)

测量手机系统重要电压是否正常，漏电流是否正常

(Measure Voltage of important power output &

Leakage Current)

①. 测得的电压必须符合规格书标准

(Voltage values should abide component specification)

②. 如无特殊要求，测得的漏电流符合赛龙标准(Leakage Current value should abide Cellon standard if no more special requirement)

1

On Going

BB1.2.1

手机板重要电压输出测试(Important power output voltage, board test)

●将供电电源调到VbatMin 和VbatMax (Vbat = 4.2V and 3.4V )

●测量以下重要电压(Measure voltage of power output)

①.VCORE/VMEM/AVDD/VDD... ②.LDO/DCDC OUTPUT…

测得的电压必须符合规格书标准

(Should abide component specification)

1BB1

BB1.2.2

整机重要电压输出测试(Important power output voltage, After assembly)

●装上所有焊接、连接在板上的物料

(PCBA Assembly of all electric connections ) ●将供电电源调到VbatMin 和VbatMax

(Vbat = 4.2V and 3.4V )

●测量以下重要电压(Measure voltage of power output) ①.VCORE/VMEM/AVDD/VDD... ②.LDO/DCDC OUTPUT…

测得的电压必须符合规格书标准

(Should abide component specification)

1BB1

BB1.2.3

手机关机漏电流测试(Leakage Current, OFF mode)

●将供电电源调到VbatMax (Vbat = 4.2V)

●查看手机关机状态漏电流(Leakage Current Test, OFF

mode)

●单系统手机(Single System Handset) <80uA

●双系统手机(Dual System Handset)

<120uA

●智能手机(Smart Phone)<120uA

2BB1

TempNom = 25°C TempLow = -15°C TempHigh = 55°C

BB1.3

手机基本功能测试

(Handset basical function

Test)

对手机的基本功能进行测试(Handset basical function

Test)

手机基本功能正常(Handset Basical Function should

be OK)

1~2

On Going

BB1.3.1显示屏功能测试

(LCD Function Tests)

所有显示屏(主屏、子屏……)显示功能测试(LCD module activation and display test. On sub and main display)

仔细观察屏的显示情况，无明显的显示问题(Visual checking, no obvious display issue)2NA

BB1.3.2

显示屏背光测试

(LCD Backlight Test)

●测试显示屏背光等级是否能正确调节(LCD backlight brightness leval adjust)

●将供电电源调到VbatMax ，将显示屏背光调到最亮等级(Vbat = VbatMax, LCD BL level = Max)●测试显示屏背光灯的工作电压和电流

●背光等级能正确调节(User could adjust LCD backlight brightness level correctly)

●背光灯工作在规格书允许的电压电流范围(acklight LED work conditions should abide datasheet requirement)

1BB1

BB1.3.3

显示屏效果测试

(LCD Display Quality)

●将供电电源调到VbatMin 和VbatMax (Vbat = VbatMin and VbatMax )

●插入充电器，在各种背光亮度等级下，观察显示效果(Charger plug in, under all different backlight brightness level,visual checking)

●最大功率通话，在各种背光亮度等级下，观察显示效果(Communication mode, max power level, under all different backlight brightness level, visual checking)

仔细观察屏的显示情况，无明显的显示问题(闪屏、对比度、背光亮度均匀度等)

(Visual checking, no obvious issue: LCD backlight flash 、contrast ratio 、 backlight brightness and uniformity issue ...)

2NA

BB1.3.4

键盘功能测试

(Keypad Function Test)

键盘功能测试，键盘音测试(Keypad activation, beeps)

键盘功能正常，键盘音功能正常(Function should be OK)

2NA

BB1.3.5

键盘背光测试

(Keypad Backlight Test)

●将供电电源调到VbatMax ，将键盘背光调到最亮等级(

Vbat = VbatMax, Keypad BL level = Max)

●测试键盘背光灯的工作电压和电流(Mesuere voltage &

current of LED)

背光灯工作在规格书允许的电压电流范围

(Backlight LED operation conditions should abide

datasheet requirement)

1BB1

BB1.3.6

马达功能测试

(Vibrator Function Test)马达功能测试(Vibrator activation)

马达功能正常(Function should be OK)2NA

BB1.3.7

马达工作电压电流测试(Keypad Backlight Test)

●将供电电源调到VbatMax ，让马达工作(Vbat = VbatMax ，active vibrator)

●测试马达的工作电压和电流(Mesuere voltage & current of Vibrator)

马达工作在规格书允许的电压电流范围

(Vibratior operation conditions should abide datasheet requirement)

1BB1

BB1.3.8

闪光灯/手电筒功能测试

(Flash Light/Torch Function Test)

闪光灯/手电筒功能测试

(Flash Light/Torch Function Test)

功能正常(Function should be OK)

2NA

BB1.3.9

闪光灯/手电筒工作电压、电流测试

(Voltage&Current Test)

●将供电电源调到VbatMax ，将闪光灯/手电筒调到最亮

等级(Vbat = VbatMax, brightness level = Max)

●测试闪光灯/手电筒工作电压和电流(Mesuere voltage

& current of LED)

闪光灯/手电筒灯工作在规格书允许的电压电流范围

(LED operation conditions should abide

datasheet requirement)

1BB1

BB1.3.10

温度检测电路测试

(Temperature Detection Circuit Test)

VBAT = VbatNom

●测试温度设置(Test temperature setting)：

TempNom 25°C /TempMin -5°C /TempMax 55°C ●将温箱温度固定在需要测试的温度，待其稳定(Keep

temperature box under a stable environment) ●将手机放入温度稳定的温箱内半小时(Put the phone in temperature box for 0.5 hour under different

temperature conditions) ●通过手机读出检测到的温度，并记录(Read temperature via phone & record it)

允许有+/-3°C 的误差

( +-3°C error could be acceptable )2BB1

BB1.3.11

电池电压检测电路测试

(Battery Voltage Detection Circuit Test)●使用精密电源代替电池作为手机供电(Use power

supply to replace battery)

●调节电源的输出电压，检查手机电池电压检测是否正

常(Check the accuracy of phone battery voltage

detection circuit)

允许有+/-0.05V 的误差

( +-0.05V error could be acceptable )

2BB1

BB1.3.12电量显示图标测试(Battery Capacity Icon Test)●使用精密电源代替电池作为手机供电(Use power supply to replace battery)

●调节电源的输出电压，检查软件是否按照HSI 的要求

设置电池电量显示、低电告警、低电禁止通话、自动关

机(Adjust power supply output until battery icon

change/low power warning/Forbid call/auto power off)●记录此电压(Record the voltage)

如无特殊要求，满足项目HIS 要求标准

(Abide project Hardware Software Interface ruls if

no more special requirements )

1BB1

[根据赛龙指定电池的特性进行各个电压点进行设定，并测试验证]

BB1.3.13

耳机座电路检查(Audio Pins Check)

插入耳机，检查如下项目(Insert headset, check items below)：

●耳机麦克功能检查(Headset MIC function Test)●耳机左声道功能检查(Headset Left Channel function Test)●耳机右声道功能检查(Headset Right Channel function Test)●耳机按键功能检查(Headset Key function Test)●在正常通话过程中，插入/拔出耳机，测试不少于100次(Plug in/out headset at least 100 times under normal communication)

●耳机所有功能正常(Headset all functions should be OK)●左右声道没有接反(There is no exchange issue between Left & Right channel)●在插入/拔出过程中，不会出现挂机(No abnormal end call occur during headset plug in/out)2

NA

[耳机接口定义PCB 板上需要兼容2种耳机设计，并根据赛龙指定耳机出货： GND-MIC-R-L MIC-GND-R-L ]

BB2.1

手机通话功能、性能测试(Handset Communication Test. Function & Performance)

正常模式、免提模式、耳机模式下，对手机的通话功能

、性能进行测试(Handset Communication Test,

Normal mode/Handsfredd mode/Headset mode.

Function & Performance)

手机在各种模式下，通话功能、性能正常(Handset

Communication function & performance should

be OK)

2

On Going

[如无特殊要求，一般项目仅需要音频功能、普通性能测试；CTA 项目或客户有特殊需求的项目，需要进行音频频响曲线测试]

BB2.1.1

受话器功能测试(Receiver Function Test)●受话器功能测试(Receiver Function Test)●受话器音量调节测试(Receiver Volume Control Test)

受话器功能正常，音量调节正常(Activation OK, Volume can be increased or decreased)

2NA

BB2.1.2

受话器待机状态噪音测试(Receiver Noise Test In Idle Mode)●待机模式下，检查受话器的噪音(Receiver noise in

Idle mode)

●插入拔出充电器，检查受话器的噪音(Receiver noise in Idle mode when plug & unplug charger)●按键，检查受话器的噪音(Receiver noise in Idle mode

when keypad pressed)受话器无噪音问题(No audio noise)2NA

BB2.1.3麦克风功能测试(Micropho

ne Function Test)

麦克风功能测试(Microphone Function Test)

麦克风功能正常(Activation OK)

2NA

BB2.1.4

一般通话模式下，TDD 噪

音、回音实验室测试(Norm

al communication mode, TDD nosie/Echo test, Use

test card)

●使用测试卡，耦合模式连接综测仪(Insert test card,communicate to test set via wireless mode )

●设定为最大发射功率(TX MAX Level )

●回环模式通话，改变手机和发射天线距离和位置，检

查是否有TDD 噪音和回音(Make a call, in loop mode,

with different position & distance between handse and

test set radiation antenna, check if there was TDD noise & echo)无TDD 噪音和回音(No TDD noise, No echo)

2NA

BB2.1.5一般通话模式下，TDD 噪音、回音实网测试(Normal communication mode, TDD nosie/Echo test, Use SIM card)

●使用SIM 卡，和座机通话(Make a call to telephone)●到电梯间或者信号不好的地方(Go to low signal place

with handset )

●检查是否有TDD 噪音和回音(check if there was TDD noise & echo)

无TDD 噪音和回音(No TDD noise, No echo)2NA

BB2.1.6免提功能测试(Handsfree

Mode Function Tests)

●测试手机免提功能(Check speaker phone activation)

●免提音量调节测试(Speaker Volume Control Test)

手机免提功能正常，音量调节正常(Activation OK.

Volume can be increased or decreased)

2NA

BB2.1.7免提通话模式下，TDD噪

音、回音实验室测试(Hand

sfreel communication

mode, TDD nosie/Echo

test, Use test card)

●使用测试卡，耦合模式连接综测仪(Insert test

card,communicate to test set via wireless mode )

●设定为最大发射功率(TX MAX Level )

●回环模式通话，改变手机和发射天线距离和位置，检

查是否有TDD噪音和回音(Make a call, in loop mode,

with different position & distance between handse and

test set radiation antenna, check if there was TDD

noise & echo)

无TDD噪音和回音(No TDD noise. No echo)2NA

BB2.1.8免提通话模式下，TDD噪

音、回音实网测试(handsfr

ee communication mode,

TDD nosie/Echo test, Use

SIM card)

●使用SIM卡，和座机通话(Make a call to telephone)

●到电梯间或者信号不好的地方(Go to low signal place

with handset )

●检查是否有TDD噪音和回音(check if there was TDD

noise & echo)

无TDD噪音和回音(No TDD noise, No echo)2NA

BB2.1.9耳机通话功能测试(Headse

t Mode Function Test)

耳机通话功能测试(Headset Mode Function Test)：

●耳机左右声道通话功能测试，音量调节测试(Right &

Left speaker function test, Volume control test)

●耳机麦克风通话功能测试(Headset microphone

function test)

●耳机挂机键功能测试(Headset key function test)

耳机所有功能正常(Headset all functions should

be OK. Volume can be increased or decreased)

2NA

BB2.1.10耳机通话模式下，TDD噪

音、回音实验室测试(Hand

sfreel communication

mode, TDD nosie/Echo

test, Use test card)

●使用测试卡，耦合模式连接综测仪(Insert test

card,communicate to test set via wireless mode )

●设定为最大发射功率(TX MAX Level )

●回环模式通话，改变手机和发射天线距离和位置，检

查是否有TDD噪音和回音(Make a call, in loop mode,

with different position & distance between handse and

test set radiation antenna, check if there was TDD

noise & echo)

无TDD噪音和回音(No TDD noise. No echo)2NA

BB2.1.11耳机通话模式下，TDD噪

音、回音实网测试(handsfr

ee communication mode,

TDD nosie/Echo test, Use

SIM card)

●使用SIM卡，和座机通话(Make a call to a telephone)

●到电梯间或者信号不好的地方(Go to low signal place

with handset )

●检查是否有TDD噪音和回音(check if there was TDD

noise & echo)

无TDD噪音和回音(No TDD noise. No echo)2NA

BB2.2音频功率及铃声响度测试(

Audio Output Power &

Speaker SPL Test,

Ringtone)

①测试所有音频输出功率(Every Audio Output Power

Test)

②测试铃声响度(Speaker SPL Test, Ringtone)

①音频输出功率必须符合规格书标准

(Should abide component specification)

②铃声响度如无特殊要求，满足赛龙公司标准

(Abide Cellon standard if no more special

requirements for SPL)

1

On

Going

BB2.2.1输出至喇叭的功率(AMP.

Power output to speaker)

●铃声(特别是客户提供的铃声)(Rington(especially use

customer'srington))

●免提通话，对方在嘈杂环境中通话、对方对着话筒吹

气(Handsfree Call, & big noise condition & people huff

to their phone mic)

●电视声音外放、收音机外放(TV，FM loudspeaker

mode)

●音频输出功率必须符合规格书标准(Should abide

component specification)1BB2

BB2.2.2输出至受话器的功率(BB

power output to receiver)

正常通话、对方在嘈杂环境中通话、对方对着话筒吹气

(Common call & big noise condition & people huff to

their phone mic)

●音频输出功率必须符合规格书标准(Should abide

component specification)1BB2

BB2.2.3输出至耳机的功率(BB

power output to headset)

●铃声(特别是客户提供的铃声)(Rington(especially use

customer'srington))

●耳机通话、对方在嘈杂环境中通话、对方对着话筒吹

气(Headset Call, & big noise condition & people huff to

their phone mic)

●电视、收音机(TV/FM headset mode)

●音频输出功率必须符合规格书标准(Should abide

component specification)

●一般来说，满足如下标准(Gernerally,please

abide standard below)

1BB2

BB2.2.4喇叭响度测试(Speaker

SPL Test)

●测试铃声(特别是客户提供的铃声)(Rington(especially

use customer'srington))

●使用声压计，A加权，高范围测试(Use sound level

meter,A, High Range Test)

●手机喇叭距测试仪器5厘米，手机喇叭距桌面至少10

厘米(Distance between handset speaker hole and test

set should be 5cm.Distance bewteen handset speaker

hole and desk surface should be at least 10cm)

如无特殊要求，满足赛龙公司标准

(Abide Cellon standard if no more special

requirements)

至少5首铃声响度(At least 5 ringtone SPL) ≥

95dB

[此为最低要求；具体项目可能根据客户需求和产

品定义提高此项要求]

1BB2

BB3.1手机充电功能测试

(Handset Charge Function

Test)

对手机的充电功能进行测试(Handset charge function

Test)

手机充电功能正常(Handset charge function should

be OK)

1

On

Going

BB3.1.1充电电流测试

(Charge Current Test)

●如果支持USB充电，请将USB充电电流限制在500mA

以内(Please limit USB charge current less than

500mA if phone support USB charge function)

●充电器充电电流根据实际项目电池容量大小定义(Plea

se define correct charge current according to battery

capacity when use charger)

●USB充电电流<500mA

(USB charge current < 500mA)

●当电池电压<3.2V时，预充电流须符合规格书标

准(Pre_charge current should abide specification

requirement when Vbat < 3.2V)

●快充电流不得超过0.7C，且需符合各自项目的要

求(Fast charge current should not exceed 0.7C &

abide project reuqirement)

●停充电流不得超过100mA (Fast charge current

should not exceed 100mA)

1BB3

BB3.1.2手机启动时间测试

(Start Up Time Test)

●电池完全放电直至电压小于2.6V，或者在小于2.6V的

条件下，直至电池保护 (Battery fully empty <2.6V or

be protected)

●插入充电器，手机需要多长时间才能点亮屏且显示正

常充电的图标？ (How many time when BB was waked

up and LCD showed the charging flag?)

如无特殊要求，此时间应该小于15分钟(No more

than 15 minutes if no more special requirements)

1BB3

BB3.1.3电池是否充满测试

(Battery Full Charge Test)

检查电池是否完全充满(Check if the battery is fully

charged) ：

充电完成后，立即拔出充电器，测试电池电压(By

voltage checking, charger disconnected & test as soon

as charge completed)

电池电压≥4.15V(Vbat ≥ 4.15V)1BB3

BB3.1.4充电时间测试

(Charge Time)

电池完全放电后(电池电压小于3.2V)，多长时间能完成

充电？

●测试环境温度：T = TempNom (Test at TempNom)

●在关机和待机情况下，都需要测试(In mode OFF and

ON)

如无特殊要求，此时间应该小于4小时(Less than

4 hours if no more special requirements)

1BB3

BB3.2手机充电安全性测试

(Handset Charge Safety

Test)

对手机的充电安全性能进行测试(Handset charge

Safety Test)

如无特殊要求，满足赛龙公司标准

(Abide Cellon standard if no more special requirements fo

SPL)

1~2

On

Going

BB3.2.1快充过程温升测试(Temper

ature rise when in fast

charge mode)

在关机和待机时(Handset On and Off )：

①. 连接充电器，使手机进入快充模式(Connect

charger, Handset runs into fast charge mode)

②. 充电30分钟，记录手机外表面的最高温度(After 30

minutes charge, record max temperature of phone

surface)

充电30分钟后，手机表面温度最高不能超过50度(

After 30 minutes charge, max temperature of

phone surface should be no bigger than 50°C )

2BB3

BB3.2.2充电器拔插测试

(Charger

connected/disconnected to

handset with/without

Battery

在关机和待机时(Handset On and Off )：

①. 先连接充电器，再放入电池(Connect charger then

battery)

②.先放入电池，再插入充电器，再取出电池(connect

battery, then charger, then

remove the battery)

●手机不会损坏(no electrical damage)

●在充电器和电池都连接时，充电功能和充电电流

正常(Charge function & current should be OK

when charger & battery were all connected)

2NA

BB3.2.3过压保护测试

(Over Voltage Protection

Test)

●电池电压为Vbatnom(Vbat=VbatNom)

●采用电源模拟充电器，将电源输出调为5V(Use power

to act as charger, set output to 5V)

●待手机正常充电后，缓慢调高电源输出，记录下停止

充电时电源的输出电压(Adjust power output higher and

higher slowly, record voltage when stopped charge)

●待手机由于保护停止充电后，缓慢调低电源输出，记

录下恢复充电时电源的输出电压(Adjust power output

lower and lower slowly, record voltage when charged

again)

●如使用过压保护芯片，请遵从其规格书要求(If

we designed with an OVP IC,test result should

abide specifiation requirement)

●如果通过软件实现过压保护，请遵从以下要求(If

we achieved OVP function by software way,

please abide rules below):

Protect Voltage: 6.6V≤ Vprotect ≤ 7V

Unprotect Voltage: 5.7V≤ Vunprotect ≤ 6.4V

1BB3

BB3.2.4过温保护测试

(Over Temperature

Protection Test)

注意：请完成1.3.8测试项后，再做此项测试(Note:

Please do CT1 test firstly)

●测试标准温度设置(Standard test temperature

setting)：55°C & -10°C

●将温箱温度固定在需要测试的温度，待其稳定(Keep

temperature box under a stable environment)

●插入充电器，将手机放入温度稳定的温箱内半小时(Pu

t the phone (with charger) in temperature box for 0.5

hour under different temperature conditions)

●记录充电保护时的温度(Record temperature when

stop charge).

●如使用过温保护芯片，请遵从其规格书要求(If

we designed with an OTP IC,test result should

abide specifiation requirement)

Protect Temperature:

●如果通过软件实现过温保护，请遵从以下要求(If

we achieved OTP function by software way,

please abide rules below):

-7°C ≤ Tprotect_min ≤ -4°C

53°C ≤ Tprotect_max ≤ 57°C

1BB3

BB4.1摄像头测试(Camera Test)对摄像头功能、性能测试(Camera Function &

Performance Test)

摄像头功能、性能正常(Function & Performance

should be OK)

2

On

Going

BB4.1.1摄像头功能测试

(Camera Function Test)测试摄像头预览、拍照、存储、视频模式功能是否正常

(Camera preview, Take photo, Photo storage, Video

mode function test)

摄像头功能正常(Function should be OK)2NA

BB4.1.2摄像头性能测试

(Camera performance Test)当电池电压为VbatMin和VbatMax时(VBAT = VbatMin &

VbatMax)

●预览模式，是否有水波纹，对焦是否正常(Preview

mode,double check abnormal line,double check focus)

●预览模式，快速移动时，是否有分屏现象(Preview

mode,fast moving, double check split line)

●预览模式，弱光照情况下，是否有明显的噪点(Previe

w mode, low illumination, double check noise dot)

●无水波纹，对焦清晰(No abnormal line, focus

clear)

●无分屏现象(No split line)

●无明显的噪点(No obvious noise dot)

2NA

BB4.1.3照片质量检查

(Photo Quality Check)

在电脑上检查所拍照片(Check phones on PC)无明显的问题(No abvious Issues)2NA

BB4.2摄像头电流测试

(Camera Current Test)

对摄像头各项电流指标进行测试(Camera Current Test)

如无特殊要求，满足赛龙公司标准

(Abide Cellon standard if no more special

requirements)

2

On

Going

BB4.2.1摄像头工作电流测试

(Camera Function Current

Test)

●将供电电源调到VbatMax(Vbat = VbatMax)

●飞行模式或者使用测试卡，连上综测仪，Paging9(Flig

ht Mode Or communicated to test set with test card,

Paging = 9)

●屏背光等级调到最亮，进入预览模式，快速移动摄像

头，记录此时的电流(LCD BL = Max Level, preview

mode, fast moving, record the current value)

●屏背光等级调到最亮，进入录像模式，快速移动摄像

头，记录此时的电流(LCD BL = Max Level, Record

mode, fast moving, record the current value)

一般来说，如无特殊情况，请遵从以下标准

(Generally, please abide standard below if there

were no more requirements & special

applications)

●预览模式(Preview mode)：

Feature Phone: ≤ 200mA

Smart Phone: ≤ 350mA

●录像模式(Record mode)：

Feature Phone: ≤ 200mA

Smart Phone: ≤ 350mA

2BB4

BB4.2.2使用摄像头后，待机电流测试

(Sleep Current Test when Used

Camera Function)

●手机已经通过待机电流测试(Fisrtly, handset should

pass CT Test)

●将供电电源调到VbatMax(Vbat = VbatMax)

●按照以下流程操作(Please operate phone according

to process)：

①.进入预览→退出预览→测试待机电流(Enable

Camera,Preview→Disable Camera→Sleep Current

Test)

②.进入预览→拍照→退出摄像头模式→测试待机电流(

Enable Camera,Preview→Take Photos→Disable

Camera→Sleep Current Test)

③.进入视频模式→录像10秒→退出视频模式→测试待

机电流(Enable Video Recorder → Record 10s →

Disable Video Recorder → Sleep Current Test)

待机底电流不超过CTx测试结果(Sleep current

should be no more than test result of CTx)

2NA

BB4.3摄像头极限环境下工作测

试

(Camera Test under

Extremity Environment)

在高低温环境下，对手机摄像头基本功能进行测试

(Camera function Test Under Extremity Environment)

测试中和测试后，摄像头功能正常(During & After

test, Camera function should be OK)

2

On

Going

BB4.3.1摄像头极限环境下工作测试

(Camera Test under Extremity

Environment)

●环境温度(Environment temperature: TempLow &

TempHigh)

●测试之前，检查摄像头预览情况，并拍照，保持于存

储卡内(Before test, do preview test & take photo, save

to memory card)

●待温度稳定后，手机放置至少2个小时(Handset must

stay at least 2 hours for each temperature)

●每隔1小时，检查一次摄像头的情况（检查预览，并拍

同样的照片）(do preview test & take same photo

every 1 hour)

●测试中，摄像头预览效果正常，拍照功能正常(D

uring test, camera preview performance should

be OK. Capture function should be OK)

●测试后，在电脑中对比所拍照片，无太大差异(A

fter test, visual checking photos on PC. No

obvious issues)

1BB4

BB5.1USB及存储卡测试(USB &

Storage Card Test)

对USB及存储卡功能、性能测试(USB & Storage Card

Function & Performance Test)

功能、性能正常(Function & Performance should

be OK)

2

On

Going

BB5.1.1USB数据线检测(USB Data

Cable Detection)

●在待机模式下，插入USB数据线(In idle mode, insert

USB cable)

●在关机模式下，插入USB数据线(In idle mode, insert

USB cable)

计算机能正确识别手机

(USB device detection OK)

2NA

BB5.1.2支持热插拔存储卡的手机

，卡检测测试(Storage

Card Detection Test, With

Plug in & Play Function)

对于支持储存卡热插拔的手机(Phone supports Plug in

& Play Function)：

①.在开机状态下，插拔存储卡，手机能正常识别(Idle

mode, plug or unplug storage card, phone could

detect correctly)

②.在关机状态下，插入存储卡，然后开机，手机能正

常识别(Power off mode, plug in storage card, phone

could detect correctly)

③.在关机状态下，拔出存储卡，然后开机，手机能正

常识别(Power off mode, unplug storage card, phone

could detect correctly)

●手机能正确识别存储卡的状态(Phone could

detect storage card correctly)

●热插拔测试时，插入/拔出卡后2秒内，手机能正

确识别(Plug & Unplug storage card, phone

detection time：Less than 2 seconds)

2NA

BB5.1.3不支持热插拔存储卡的手

机，卡检测测试(Storage

Card Detection Test,

Without Plug in & Play

Function)

对于不支持储存卡热插拔的手机(Phone do not support

Plug in & Play Function)：

①.在关机状态下，插入存储卡，然后开机，手机能正

常识别(Power off mode, plug in storage card, phone

could detect correctly)

②.在关机状态下，拔出存储卡，然后开机，手机能正

常识别(Power off mode, unplug storage card, phone

could detect correctly)

●手机能正确识别存储卡的状态(Phone could

detect storage card correctly)

●插入存储卡开机，出现待机界面后2秒内，手机

能正确识别存储卡(Phone power on with storage

card. After shows idle desktop, phone could

detect storage card no less than 2 seconds)

2NA

BB5.1.4USB2.0全速，数据传输速

度测试(Speed of Data

Transfer, USB2.0 Full

Speed)

●通过USB连接电脑(Connect to PC via USB data

cable)

●通过拷贝大于50M的文件，计算传输速度(Transfer

data size > 50MB, record transfer time then we get the

speed)

●理论传输速度：1.5MB/S (max)

●从PC拷贝文件至存储卡,速度大于600KB/秒(Cop

y data from PC to storage card, speed >

600KB/S)

●从PC拷贝文件至手机内部存储器，速度大于400

KB/秒(Copy data from PC to phone memory,

speed > 400KB/S)

●从存储卡拷贝文件至PC，速度大于800KB/秒(C

opy data from storage card to PC, speed >

800KB/S)

●从手机内部存储器拷贝文件至PC，速度大于600

KB/秒(Copy data from phone memroy to PC,

speed > 600KB/S)

2BB5

BB5.1.5USB2.0高速，数据传输速

度测试(Speed of Data

Transfer, USB2.0 High

Speed)

●通过USB连接电脑(Connect to PC via USB data

cable)

●通过拷贝大于50M的文件，计算传输速度(Transfer

data size > 50MB, record transfer time then we get the

speed)

●理论传输速度：60MB/S (max)

●从PC拷贝文件至存储卡,速度大于3MB/秒(Copy

data from PC to storage card, speed > 3MB/S)

●从PC拷贝文件至手机内部存储器，速度大于2M

B/秒(Copy data from PC to phone memory,

speed > 2MB/S)

●从存储卡拷贝文件至PC，速度大于7MB/秒(Cop

y data from storage card to PC, speed > 7MB/S)

●从手机内部存储器拷贝文件至PC，速度大于5M

B/秒(Copy data from phone memroy to PC,

speed > 5MB/S)

2BB5

BB5.2存储卡电流测试

(Storage Card Current

Test)

对存储卡各项电流指标进行测试(Storage Card Current

Test)

如无特殊要求，满足赛龙公司标准

(Abide Cellon standard if no more special

requirements)

2

On

Going

BB5.2.1插入存储卡后，待机电流测试

(Sleep Current Test with

Storage Card)

●手机已经通过待机电流测试(Fisrtly, handset should

pass CT Test)

●将供电电源调到VbatMax(Vbat =VbatMax)

●手机插入存储卡，测试待机电流(Sleep Current Test

with Storage Card)

待机底电流不超过CTx测试结果(Sleep current

should be no more than test result of CTx)

2NA

BB6.1MP3及MP4测试(MP3 &

MP4 Test)

对MP3及MP4功能、电流测试(USB & Storage Card

Function & Performance Test)

功能、电流正常(Function & power consumption

should be OK)

2

On

Going

BB6.1.1MP3工作电流测试，耳机模式

(MP3 Play Current Test,

Headset mode)

●音频参数调整完成，或使用赛龙默认音频参数(Audio

parameters adjustment finished or set Cellon default

audio parameters)

●将供电电源调到VbatMax(Vbat = VbatMax)

●飞行模式或者使用测试卡，连上综测仪，Paging9(Flig

ht Mode Or communicated to test set with test card,

Paging = 9)

●插入耳机，播放指定MP3曲目，最大音量正常播放，

待屏背光熄灭1分钟后，开始测试，每次测试时间1分钟

(With headset, Play standard MP3 with max volume.

Started test unitl LCD backlight turns off 1mins later.

Every test lasts for 1mins)

一般来说，如无特殊情况，请遵从以下标准

(Generally, please abide standard below if there

were no more requirements & special

applications)

Feature Phone ≤ 50mA

Smart Phone ≤ 100mA

2BB6

BB6.1.2MP3工作电流测试，外放模式

(MP3 Play Current Test,

Loudspeaker mode)

●音频参数调整完成，或使用赛龙默认音频参数(Audio

parameters adjustment finished or set Cellon default

audio parameters)

●将供电电源调到VbatMax(Vbat = VbatMax)

●飞行模式或者使用测试卡，连上综测仪，Paging9(Flig

ht Mode Or communicated to test set with test card,

Paging = 9)

●播放指定MP3曲目，最大音量正常外放，待屏背光熄

灭1分钟后，开始测试，每次测试时间1分钟(Loudspea

ker mode, Play standard MP3 with max volume.

Started test unitl LCD backlight turns off 1mins later.

Every test lasts for 1mins)

●此项测试结果作为参考(BB6.1.2 test value just

for reference)

●一般来说，如无特殊情况，请遵从以下标准

(Generally, please abide standard below if there

were no more requirements & special

applications)

≤ 150mA

2BB6

BB6.1.3MP4工作电流测试，耳机模式

(MP4 Play Current Test,

Headset mode)

●音频参数调整完成，或使用赛龙默认音频参数(Audio

parameters adjustment finished or set Cellon default

audio parameters)

●将供电电源调到VbatMax(Vbat = VbatMax)

●飞行模式或者使用测试卡，连上综测仪，Paging9(Flig

ht Mode Or communicated to test set with test card,

Paging = 9)

●插入耳机，播放指定MP4节目，最大音量正常播放，

待屏背光熄灭1分钟后，开始测试，每次测试时间1分钟

(With headset, Play standard MP4 with max volume.

Started test unitl LCD backlight turns off 1mins later.

Every test lasts for 1mins)

一般来说，如无特殊情况，请遵从以下标准

(Generally, please abide standard below if there

were no more requirements & special

applications)

≤180mA

2BB6

BB6.1.4MP4工作电流测试，外放模式

(MP4 Play Current Test,

Loudspeaker mode)

●音频参数调整完成，或使用赛龙默认音频参数(Audio

parameters adjustment finished or set Cellon default

audio parameters)

●将供电电源调到VbatNom(Vbat = VbatNom)

●飞行模式或者使用测试卡，连上综测仪，Paging9(Flig

ht Mode Or communicated to test set with test card,

Paging = 9)

●播放指定MP4节目，最大音量正常外放，待屏背光熄

灭1分钟后，开始测试，每次测试时间1分钟(Loudspea

ker mode, Play standard MP4 with max volume.

Started test unitl LCD backlight turns off 1mins later.

Every test lasts for 1mins)

一般来说，如无特殊情况，请遵从以下标准

(Generally, please abide standard below if there

were no more requirements & special

applications)

≤ 250mA

2BB6

BB6.1.5播放MP3后，待机电流测试

(Sleep Current Test After MP3

Played)

●手机已经通过待机电流测试(Fisrtly, handset should

pass CT Test)

●将供电电源调到VbatMax(Vbat = VbatMax)

●按照以下流程操作(Please operate phone according

to process)：

播放MP3→退出MP3播放→测试待机电流(Play MP3

→Disable MP3 Play→Sleep Current Test)

待机底电流不超过CTx测试结果(Sleep current

should be no more than test result of CTx)

2NA

BB6.1.6播放MP4后，待机电流测试

(Sleep Current Test After MP4

Played)

●手机已经通过待机电流测试(Fisrtly, handset should

pass CT Test)

●将供电电源调到VbatMax(Vbat = VbatMax)

●按照以下流程操作(Please operate phone according

to process)：

播放MP4→退出MP4播放→测试待机电流(Play MP4

→Disable MP4 Play→Sleep Current Test)

待机底电流不超过CTx测试结果(Sleep current

should be no more than test result of CTx)

2NA

BB6.2MP3极限环境下连续播放

测试

(MP3 Continuate Play

Test under Extremity

Environment)

在高低温环境下，MP3连续播放测试

(MP3 Continuate Play Test under Extremity

Environment)

测试中和测试后，MP3功能正常(During & After

test, MP3 Play function should be OK)

2

On

Going

BB6.2.1MP3极限环境下工作测试

(MP3 Continuate Play Test

under Extremity Environment)

●环境温度(Environment temperature: TempLow &

TempHigh)

●使用赛龙标准测试曲目测试两台手机，一台带耳机，

一台不带耳机(Play Cellon standard test songs. 1pcs

handset with headset, 1pcs handset without headset)

●待温度稳定后，MP3连续播放2个小时((MP3

continuate play for 2 hours for each temperature)

●每隔1小时，检查一次MP3的工作情况(Check MP3

play every 1 hour)

测试中和测试后，MP3功能正常(During & After

test, MP3 Play function should be OK)

2NA

BB9.1高低温基本测试(High/Low

Temperature Environment

Test--Basical)

在高低温环境下，对手机的基本功能进行测试(Handset

basical function Test Under Extremity Temperature

Condition)

测试过程中和测试后，手机基本功能正常(Handset

Basical Function should be OK during & after

test))

2

On

Going

BB9.1.1手机开机、关机测试(Hand

set Power on/OFF Test)

●环境温度(Environment temperature: TempLow &

TempHigh)

●采用电池供电(Use battery for power supply)

●一台手机不插SIM卡，一台手机插入SIM卡(Handset

with & without SIM Card)

●待温度稳定后，手机放置其中至少2个小时(Handset

must stay at least 2 hour for each temperature)

●每隔1小时，检查一次手机的开关机情况(Power on/off

every 1 hour)

测试中和测试后，手机开关机正常(During & After

test, handset power on/off should be OK)

2NA

BB9.1.2手机下载测试(Downloadin

g in temperature)

●环境温度(Environment temperature: TempLow &

TempHigh)

●采用电池供电(Use battery for power supply)

●一台手机不插SIM卡，一台手机插入SIM卡(Handset

with & without SIM Card)

●待温度稳定后，手机放置其中至少1个小时(Handset

must stay at least 1 hour for each temperature)

1小时后，手机下载功能正常(Handset download

function should be OK after 1 hour test)

2NA

BB9.1.3手机读写SIM卡测试(Read

/ write with SIM card).

●环境温度(Environment temperature: TempLow &

TempHigh)

●采用电池供电(Use battery for power supply)

●待温度稳定后，手机放置其中至少2个小时(Handset

must stay at least 2 hour for each temperature)

●每隔1小时，检查一次手机的SIM卡读写情况(Check

SIM card access every 1 hour)

测试中和测试后，手机读写SIM卡正常(During &

After test, handset could read & write SIM card

correctly)

2NA

BB9.1.4屏显示测试(LCD Display)●环境温度(Environment temperature: TempLow &

TempHigh)

●采用电池供电(Use battery for power supply)

●待温度稳定后，手机放置其中至少2个小时(Handset

must stay at least 2 hours for each temperature)

●每隔1小时，检查一次屏的显示情况(Check LCD

display performance every 1 hour)

测试中和测试后，屏显示正常(During & After test,

LCD display performance should be OK)

2NA

BB9.1.5手机通话测试(Communica

tion Test)

●环境温度(Environment temperature: TempLow &

TempHigh)

●采用电池供电(Use battery for power supply)

●待温度稳定后，手机放置其中，保持通话至少2个小时

(Handset must call at least 2 hours for each

temperature)

●每隔1小时，检查一次屏的显示情况(Check handset

communication status every 1 hour)

测试中和测试后，手机通话正常(During & After

test, handset communication should be OK)

2NA

BB9.1.6手机充电测试(Charge

Test).

●环境温度(Environment temperature): 0 °C, +40°C

●采用电池供电(Use battery for power supply)

●待温度稳定后，手机插上充电器，放置其中至少1个小

时(Handset must stay at least 1 hour for each

temperature with charger)

测试中和测试后，手机充电正常(During & After

test, charge should be OK)

2NA

BB9.2抗静电能力测试(ESD test)对手机ESD性能进行测试(ESD test )测试过程中和测试后，手机基本功能正常(Handset

Basical Function should be OK during & after

test))

2

On

Going

BB9.2.1手机主板静电测试(Board

ESD Test)

此测试旨在于检验主板地抗静电能力，如果主板没有太

大的改动，一般来说，只在P1测试(To check main

PCB board ESD performance. Generally, just test in

P1 if there were no big changes )

●主板连接屏和充电器(Main board+Charger+LCD)

●测试点为主板露铜区和屏蔽盖(Test point: GND area

+ Shielding)

●测试空气放电和接触放电(Air discharge & contact

discharge)

●如果没有对屏的保护，在测试过程中，允许出现

开关机后可恢复的白屏、花屏、闪屏现象

(If there was no any protection to LCD,white

screen, wrong LCD show,flash LCD could be

acceptable.But these issues should be restorable

after power on again) ①.空气放电须通过+/-

8KV(Air discharge: PASS +/-8KV)

②.接触放电须通过+/-4KV(Contact discharge:

PASS +/-4KV)

2NA

BB9.2.2天线馈点静电测试

(Antenna Feedback Pad

ESD Test)

此测试旨在于检验PA电路抗静电能力，如果主板没有

太大的改动，一般来说，只在P1测试(To check RF PA

circuit ESD performance. Generally, just test in P1 if

there were no big changes )

●主板连接屏和充电器(Main board+Charger+LCD)

●测试点为天线馈点(Test point: Antenna PAD)

●测试接触放电(Contact discharge)

●接触放电须通过+/-3KV(Contact discharge:

PASS +/-3KV)

●静电测试完成后，射频性能无异常

(After test, RF performance should be OK)

2NA

BB9.2.3手机整机静电测试(PhoneE

SD Test)

●整机测试空气放电和接触放电(Air discharge &

contact discharge)

①.空气放电须通过+/-12KV(Air discharge: PASS

+/-12KV)

②.接触放电须通过+/-8KV(Contact discharge:

PASS +/-8KV)

通过标准：

●在测试过程中，无任何失效(No any failure

occured during test process)

2NA

BB9.2.4手机整机静电测试后检查(

Phone check after ESD

test)

整机已经通过BB9.2.3的测试(Pass BB9.2.3 test) 测试后，各功能模块工作正常2BB9

CT3.12G双卡单通手机待机电流

测试(Dual Stand by, Single

Talk Handset Sleep

Current Test, 2G)

连上综测仪测试手机待机电流

(Sleep Current Test With Communication Test Set)

如无特殊要求，满足赛龙公司标准

(Abide Cellon standard if no more special

requirements)

2

On

Going

CT3.1.1双卡单通手机，卡1待机电

流实验室测试(Dual SIM,

Single Talk Handset Sleep

Current Test) -- SIM1 with

test card

按照2.1.1的方法测试SIM1单卡待机(Same test way as

description in 2.1.1 when inserting one test card into

SIM1)

一般来说，如无特殊情况，请遵从以下标准

(Generally, please abide standard below if there

were no more requirements & special

applications)

①. Paging 2 : ≤ 1.5mA

②. Paging 5 : ≤ 1.2mA

③. Paging 9 : ≤ 1.0mA

2CT3

CT3.1.2双卡单通手机，卡2待机电

流实验室测试(Dual SIM,

Single Talk Handset Sleep

Current Test) -- SIM2 with

test card

按照2.1.1的方法测试SIM2单卡待机(Same test way as

description in 2.1.1 when inserting one test card into

SIM2)

一般来说，如无特殊情况，请遵从以下标准

(Generally, please abide standard below if there

were no more requirements & special

applications)

①. Paging 2 : ≤ 1.5mA

②. Paging 5 : ≤ 1.2mA

③. Paging 9 : ≤ 1.0mA

2CT3

CT3.1.3双卡单通手机，双卡待机

电流实验室测试(Dual SIM,

Single Talk Handset Sleep

Current Test) -- Dual Test

Card

按照2.1.1的方法测试双卡待机(Same test way as

description in 2.1.1 when inserting one test card into

SIM1 & SIM2)

一般来说，如无特殊情况，请遵从以下标准

(Generally, please abide standard below if there

were no more requirements & special

applications)

①. Paging 2 : ≤ 1.5mA

②. Paging 5 : ≤ 1.2mA

③. Paging 9 : ≤ 1.0mA

2CT3

CT3.1.4双卡单通手机，卡1实网待

机电流测试

(Handset Sleep Current

Test) -- Singlel Real SIM

Card, SIM1

●手机射频已经校准，手机组装完整(RF has been

adjusted, Handset fully assembled)

●将供电电源调到VbatMax(Vbat = VbatMax )

●使用实网SIM卡，成功注册(Successful registration

with real SIM card)

●待屏背光熄灭2分钟后，开始测试，测试时间10分钟(

Started test unitl LCD backlight turns off 2mins later.

test lasts for 5mins)

●测试过程中，无短信、电话、闹铃等任何可以让基带

唤醒的事件发生(During test process, None of affairs

occured which would wake up baseband, such as

SMS, call, Alarm clock etc.)

一般来说，如无特殊情况，请遵从以下标准

(Generally, please abide standard below if there

were no more requirements & special

applications)

≤ 2.5mA

2CT3

CT3.1.5双卡单通手机，卡2实网待

机电流测试

(Handset Sleep Current

Test) -- Singlel Real SIM

Card, SIM2

●手机射频已经校准，手机组装完整(RF has been

adjusted, Handset fully assembled)

●将供电电源调到VbatMax(Vbat = VbatMax )

●使用实网SIM卡，成功注册(Successful registration

with real SIM card)

●待屏背光熄灭2分钟后，开始测试，测试时间10分钟(

Started test unitl LCD backlight turns off 2mins later.

test lasts for 5mins)

●测试过程中，无短信、电话、闹铃等任何可以让基带

唤醒的事件发生(During test process, None of affairs

occured which would wake up baseband, such as

SMS, call, Alarm clock etc.)

一般来说，如无特殊情况，请遵从以下标准

(Generally, please abide standard below if there

were no more requirements & special

applications)

≤ 2.5mA

2CT3

CT3.1.6双卡单通手机，双卡待机

电流实网测试(Dual SIM,

Single Talk Handset Sleep

Current Test) -- Dual Real

SIM Card

●手机射频已经校准，手机组装完整(RF has been

adjusted, Handset fully assembled)

●将供电电源调到VbatMax(Vbat = VbatMax )

●使用两张实网SIM卡，成功注册(Successful

registration with dual real SIM cards)

●待屏背光熄灭2分钟后，开始测试，测试时间10分钟(

Started test unitl LCD backlight turns off 2mins later.

test lasts for 5mins)

●测试过程中，无短信、电话、闹铃等任何可以让基带

唤醒的事件发生(During test process, None of affairs

occured which would wake up baseband, such as

SMS, call, Alarm clock etc.)

一般来说，如无特殊情况，请遵从以下标准

(Generally, please abide standard below if there

were no more requirements & special

applications)

≤ 3mA

2CT3

CT3.22G双卡单通手机通话/通信

电流测试(Dual Stand by,

Single

Talk/Communication

Handset Current Double

Check, 2G)

连上综测仪测试手机通话电流

(Talk Current Test With Communication Test Set)

如无特殊要求，满足赛龙公司标准

(Abide Cellon standard if no more special

requirements)

2

On

Going

CT3.2.1SIM1实验室通话电流测试

(Handset Talk Current

Test) -- Singlel Test Card,

Inserting into SIM1

●手机射频已经校准，手机组装完整(RF has been

adjusted, Handset fully assembled)

●将供电电源调到VbatMax(Vbat = VbatMax)

●使用测试卡，插入SIM1，连上综测仪，测试各频段高

低功率等级通话电流(Communicated to test set with

test card, inserting into SIM1. Test every band with

PCL = Min, Max)

●通话开始，待屏背光熄灭后，开始测试，每次测试时

间2分钟(Call the handset & Start test unitl LCD

backlight turns off. Every test lasts for 2mins)

一般来说，如无特殊情况，请遵从以下标准

(Generally, please abide standard below if there

were no more requirements & special

applications)

●850/900

①. PCL 5 : ≤ 230mA

②. PCL19 : ≤ 100mA

●1800/1900

①. PCL 0 : ≤ 200mA

②. PCL15 : ≤ 100mA

2CT3

CT3.2.2SIM2实验室通话电流测试

(Handset Talk Current

Test) -- Singlel Test Card,

Inserting into SIM2

●手机射频已经校准，手机组装完整(RF has been

adjusted, Handset fully assembled)

●将供电电源调到VbatMax(Vbat = VbatMax)

●使用测试卡，插入SIM2，连上综测仪，测试各频段高

低功率等级通话电流(Communicated to test set with

test card, inserting into SIM2. Test every band with

PCL = Min, Max)

●通话开始，待屏背光熄灭后，开始测试，每次测试时

间2分钟(Call the handset & Start test unitl LCD

backlight turns off. Every test lasts for 2mins)

一般来说，如无特殊情况，请遵从以下标准

(Generally, please abide standard below if there

were no more requirements & special

applications)

●850/900

①. PCL 5 : ≤ 230mA

②. PCL19 : ≤ 100mA

●1800/1900

①. PCL 0 : ≤ 200mA

②. PCL15 : ≤ 100mA

2CT3

CT3.2.3SIM1或者SIM2实验室GPR

S电流测试

(Handset Communication

mode consumption –

GPRS) -- Singlel Test

Card, SIM1 or SIM2

●手机射频已经校准，手机组装完整(RF has been

adjusted, Handset fully assembled)

●将供电电源调到VbatMax(Vbat = VbatMax)

●将屏背光调到最亮(LCD BL Level = Max)

●使用测试卡，连上综测仪，测试各频段高低功率等级

GPRS电流(Communicated to test set with test card,

every band with PCL = Min, Max)：

1.850或者900频段两个时隙分别以高低功率等级发射(8

50/900Tx level max(5) and min(19) at the same time)

2.1800或者1900频段两个时隙分别以高低功率等级发

射(1800/1900Tx level max(0) and min(15) at the same

time)

3.GPRS编码方式1和4都要测试(Coding schemes,1

and 4)

一般来说，如无特殊情况，请遵从以下标准

(Generally, please abide standard below if there

were no more requirements & special

applications)

●850/900

≤ 250mA

●1800/1900

≤ 180mA

2CT3

CT3.2.4SIM1或者SIM2实验室EGP

RS电流测试

(Handset Communication

mode consumption –

EGPRS) -- Singlel Test

Card, SIM1 or SIM2

●手机射频已经校准，手机组装完整(RF has been

adjusted, Handset fully assembled)

●将供电电源调到VbatMax(Vbat = VbatMax)

●将屏背光调到最亮(LCD BL Level = Max)

●使用测试卡，连上综测仪，测试各频段高低功率等级

GPRS电流(Communicated to test set with test card,

every band with PCL = Min, Max)：

1.850或者900频段分别以高低功率等级发射(850/900Tx

level max(8) and min(19) at the same time)

2.1800或者1900频段分别以高低功率等级发射(1800/19

00Tx level max(2) and min(15) at the same time)

3.编码方式5和9都要测试(Coding schemes,5 and 8)

一般来说，如无特殊情况，请遵从以下标准

(Generally, please abide standard below if there

were no more requirements & special

applications)

●850/900

≤ 300mA

●1800/1900

≤ 230mA

2CT3

CT6.12G双卡双通手机待机电流

检查(Dual Stand by, Dual

Talk Handset Sleep

Current Double Check,

2G)

通过4.1测试后，对手机进行各种操作后，检查待机电

流是否正常

(Operating handset applications, then double check

Sleep current be OK or not. Of course, you should

achieve 4.1 test firstly)

对手机各种操作后，待机电流还是满足4.1的要求(

After applications operation, handset Sleep

current should abide the standard of 4.1)

2

On

Going

CT6.1.1SIM1主叫结束后的待机电

流(Handset Sleep Current

After a SIM1 Call hang off--

Call out)

●使用测试卡或者实网卡，插入SIM1，呼出通话5秒，

然后结束通话(Use test card or real SIM card, inserting

into SIM1, call out for 5 seconds, then hand off)

●待屏背光熄灭2分钟后，开始检查待机电流(Check

Sleep current unitl LCD backlight turns off 2mins later)

待机电流不超过4.1测试结果(Sleep current no

more than test result of 4.1)

2NA

CT6.1.2SIM2主叫结束后的待机电

流(Handset Sleep Current

After a SIM1 Call hang off--

Call out)

●使用测试卡或者实网卡，插入SIM2，呼出通话5秒，

然后结束通话(Use test card or real SIM card, inserting

into SIM2, call out for 5 seconds, then hand off)

●待屏背光熄灭2分钟后，开始检查待机电流(Check

Sleep current unitl LCD backlight turns off 2mins later)

待机电流不超过4.1测试结果(Sleep current no

more than test result of 4.1)

2NA

CT6.1.3SIM1被叫结束后的待机电

流(Handset Sleep Current

After a SIM1 Call hang off--

Call in)

●使用测试卡或者实网卡，插入SIM1，呼入通话5秒，

然后结束通话(Use test card or real SIM card, inserting

into SIM1, call in for 5 seconds, then hand off)

●待屏背光熄灭2分钟后，开始检查待机电流(Check

Sleep current unitl LCD backlight turns off 2mins later)

待机电流不超过4.1测试结果(Sleep current no

more than test result of 4.1)

2NA

CT6.1.4SIM2被叫结束后的待机电

流(Handset Sleep Current

After a SIM2 Call hang off--

Call in)

●使用测试卡或者实网卡，插入SIM2，呼入通话5秒，

然后结束通话(Use test card or real SIM card, inserting

into SIM2, call in for 5 seconds, then hand off)

●待屏背光熄灭2分钟后，开始检查待机电流(Check

Sleep current unitl LCD backlight turns off 2mins later)

待机电流不超过4.1测试结果(Sleep current no

more than test result of 4.1)

2NA

CT6.1.5SIM1未接电话后的待机电

流(Handset Sleep Current

After Missing Call, SIM1)

●使用测试卡或者实网卡，插入SIM1，呼入通话，不接

听，再挂断(Use test card or real SIM card, inserting

into SIM1, call in but do not answer, then end call in)

●待屏背光熄灭2分钟后，开始检查待机电流(Check

Sleep current unitl LCD backlight turns off 2mins later)

待机电流不超过4.1测试结果(Sleep current no

more than test result of 4.1)

2NA

CT6.1.6SIM2未接电话后的待机电

流(Handset Sleep Current

After Missing Call, SIM2)

●使用测试卡或者实网卡，插入SIM2，呼入通话，不接

听，再挂断(Use test card or real SIM card, inserting

into SIM2, call in but do not answer, then end call in)

●待屏背光熄灭2分钟后，开始检查待机电流(Check

Sleep current unitl LCD backlight turns off 2mins later)

待机电流不超过4.1测试结果(Sleep current no

more than test result of 4.1)

2NA

CT6.1.7插入耳机后的待机电流

(Handset Sleep Current

After Headset Pluging In)

●使用测试卡或者实网卡，插入耳机(Use test card or

real SIM card, with Headset)

●待屏背光熄灭2分钟后，开始检查待机电流(Check

Sleep current unitl LCD backlight turns off 2mins later)

待机电流不超过4.1测试结果(Sleep current no

more than test result of 4.1)

2NA

CT6.1.8拔出耳机后的待机电流

(Handset Sleep Current

After Headset Pluging Off)

●使用测试卡或者实网卡，插入耳机；检测到耳机后，

再拔出耳机(Use test card or real SIM card, with

Headset pluging in. Plug off headset when headset

detection successful)

●待屏背光熄灭2分钟后，开始检查待机电流(Check

Sleep current unitl LCD backlight turns off 2mins later)

待机电流不超过4.1测试结果(Sleep current no

more than test result of 4.1)

2NA

CT6.1.9闹钟停止后的待机电流

(Handset Sleep Current

After Alarm Clock Stop)

●使用测试卡或者实网卡，设定闹钟；闹钟启动后，停

止闹钟(Use test card or real SIM card, set alarm clock.

Stop alarm clock when it was actived)

●待屏背光熄灭2分钟后，开始检查待机电流(Check

Sleep current unitl LCD backlight turns off 2mins later)

待机电流不超过4.1测试结果(Sleep current no

more than test result of 4.1)

2NA

WM1.1调频收音机测试(FM Test)对调频收音机功能、性能测试(FM Function &

Performance Test)

调频收音机功能、性能正常(Function &

Performance should be OK)

2

On

Going

WM1.1.1调频收音机功能测试

(FM Function Test)测试调频收音机自动搜台、手动搜台、音量控制、外放

功能是否正常(Auto search; Manual search; Volume

Control; Loudness Speaker)

调频收音机功能正常(Function should be OK)2NA

WM1.1.2耳机检测功能测试

(Headset Detection Test)

在使用调频收音机的时候，插入、拔出耳机(Plug &

un_plug headset When using FM)

耳机识别功能正常(Headset detection should be

OK)

2NA

WM1.1.3调频收音机传导性能测试

(FM Performance Test--

Conductive mode)

●测试频段(Test Frequency)：

fRF=88MHZ、93MHZ、98MHz、103MHz、108MHz.

●仪器设置(Configuration)：

Δf =22.5KHz

fmod = 1 kHz

BAF= 300 Hz to 15 kHz

●灵敏度测试(Sensitivity)：当测试仪器SINAD为26 dB

+/- 1 dB(ch1)时，记录下此时的灵敏度值(Audio

analyzer SINAD = 26 dB +/- 1 dB(ch1), then record RF

level.)

●信噪比测试(SNR)：设定仪器RF等级为60

dBμV，记录下此时的SNR. (Set RF level=60 dBμV,

then record SNR)

●总失真测试(THD)：设定仪器RF等级为60

dBμV，记录下此时的THD. (Set RF level=60 dBμV,

then record THD)

如无特殊要求，满足规格书标准

(Abide IC Spec. if no more special requirements)

可以参考赛龙公司要求(FYI. Cellon Standard)：

①. Sensitivity ≤3dBμV

②. SNR ≥-55dB

③.THD ≤ 0.3%

2WM1

WM1.1.4调频收音机对比性能测试

(FM Performance Test--

Compare Test)

对比样机(Benchmark): C2097

●在正常信号和弱信号下，自动搜台的能力测试(auto

search ability under normal & bad FM radio signal)

●在正常信号和弱信号下，调频收音机性能效果对比测

试(FM performance under normal and bad FM radio

signal)

●在弱信号下，按键和刷屏时，调频收音机是否有明显

噪音("Click" noise under bad FM radio signal when

key_press & refresh LCD)

●如无特殊要求，自动搜台的能力不会比对比机差

(auto search ability no less than benchmark)

●如无特殊要求，收音机性能效果不会比对比机差

(FM Performance no bad than benchmark)

●弱信号下按键、刷屏时，无明显噪音(No

abvious noise)

2WM1

WM1.2调频收音机电流测试

(FM Current Test)

对调频收音机各项电流指标进行测试(FM Current Test)

如无特殊要求，满足赛龙公司标准

(Abide Cellon standard if no more special

requirements)

2

On

Going

WM1.2.1调频收音机工作电流测试，耳

机模式

(FM Function Current Test,

Headset mode)

●音频参数调整完成，或使用赛龙默认音频参数(Audio

parameters adjustment finished or set Cellon default

audio parameters)

●将供电电源调到VbatMax(Vbat = VbatMax)

●飞行模式或者使用测试卡，连上综测仪，Paging9(Flig

ht Mode Or communicated to test set with test card,

Paging = 9)

●插入耳机，开启收音机功能，最大音量正常播放，待

屏背光熄灭1分钟后，开始测试，每次测试时间2分钟(

With headset, Play FM with max volume. Started test

unitl LCD backlight turns off 1mins later. Every test

lasts for 2mins)

一般来说，如无特殊情况，请遵从以下标准

(Generally, please abide standard below if there

were no more requirements & special

applications)

①.单独FM芯片设计(Dedicated FM IC):

≤ 30mA

②.ATV集成FM芯片设计(Integrated in ATV IC):

≤ 180mA

2WM1

WM1.2.2调频收音机工作电流测试，外

放模式

(FM Function Current Test,

Loudspeaker mode)

●音频参数调整完成，或使用赛龙默认音频参数(Audio

parameters adjustment finished or set Cellon default

audio parameters)

●将供电电源调到VbatMax(Vbat = VbatMax)

●飞行模式或者使用测试卡，连上综测仪，Paging9(Flig

ht Mode Or communicated to test set with test card,

Paging = 9)

●插入耳机，开启收音机功能，最大音量外放播放，待

屏背光熄灭1分钟后，开始测试，每次测试时间2分钟(

With headset, Loudspeaker mode, Play FM with max

volume. Started test unitl LCD backlight turns off

1mins later. Every test lasts for 2mins)

●此项测试结果作为参考(5.2.2 test value just for

reference)

●一般来说，如无特殊情况，请遵从以下标准

(Generally, please abide standard below if there

were no more requirements & special

applications)

①.单独FM芯片设计(Dedicated FM IC):

≤ 100mA

②.ATV集成FM芯片设计(Integrated in ATV IC):

≤ 250mA

2WM1

WM1.2.3调频收音机关闭后，待机电流

测试

(Sleep Current Test when FM

Closed)

●手机已经通过待机电流测试(Fisrtly, handset should

pass CT Test)

●将供电电源调到VbatMax(Vbat = VbatMax)

●按照以下流程操作：插入耳机→开启收音机→

自动搜台→选定某台→正常收听→关闭收音机→

测试待机电流(Please operate phone according to

process: Plug in headset → Enable FM → Auto

Search → Selete One Channel → FM Play → Disable

FM → Sleep Current Test)

待机底电流不超过CTx测试结果(Sleep current

should be no more than test result of CTx)

2NA

WM1.3调频收音机极限环境下工

作测试

(FM Test under Extremity

Environment)

在高低温环境下，对手机调频收音机基本功能进行测试

(FM function Test Under Extremity Environment)

测试中和测试后，调频收音机功能正常(During &

After test, FM function should be OK)

2

On

Going

WM1.3.1调频收音机极限环境下工作测

试

(FM Test)

●环境温度(Environment temperature: TempLow &

TempHigh)

●待温度稳定后，手机插入耳机，播放FM至少2个小时(

Handset must stay at least 2 hours for each

temperature with FM on)

●每隔1小时，检查一次FM的工作情况(Check FM

function every 1 hour)

测试中和测试后，调频收音机功能正常(During &

After test, FM function should be OK)

2NA

[整机ESD打完后,FM不得失效或性能恶化]

WM2.1蓝牙测试(BT Test)对蓝牙功能、性能测试(Bluetooth Function &

Performance Test)

功能、性能正常(Function & Performance should

be OK)

2

On

Going

WM2.1.1蓝牙射频性能测试

(BT RF Performance Test)●传导测试(Conductive Mode Test)

●连上蓝牙测试设备(Communicate to BT Test Set)

●对平均功率、初始载波容限、载波频率漂移、调制特

性、相邻信道功率ACP、20db带宽、接收灵敏度进行测

试并记录(Test Items: Average Power, Initial Carrier,

carrier frequence drift,Modulation Characteristic, TX

Output Spectrum Adjacent Channel Power,TX Output

Spectrum 20dB Bandwidth, Rx sensitivity)

●平均功率(Average Power) : -6dBm~+4dBm

●初始载波容限(Initial Carrier) : <+/-50KHz

●载波频率漂移(carrier frequence drift ):< +/-

25KHZ(DH1); <+/-40KHZ(DH3,DH5);

●调制特性(Modulation Characteristic) :

140KHz~175KHz

●相邻信道功率ACP(Adjacent channel power)

●20db带宽(20db bandwidth)

●接收灵敏度(Rx sensitivity)：<0.1%,-78dBm

2WM2

WM2.1.2蓝牙1.1/1.2数据传输测试

(Date Transmit Test,

BT1.1/1.2)

●将蓝牙收发器连接电脑(Connect BT R/T device to

PC)

●在无障碍物遮挡的情况下，保持手机和收发器10米距

离，测试数据传输(Test distance between handset &

BT R/T device = 10m. There is no block thing between

handset & BT R/T device)

●传输至少5MB的数据，计算传输速度(Transfer data

size > 5MB, record transfer time then we get the

speed)

●理论传输速度：90KB/S (max)

●从PC传送文件至手机存储看，速度大于50KB/秒

(Transfer data from PC to handset, speed >

50KB/S)

●从手机存储卡传送文件至PC，速度大于50KB/秒

(Transfer data from PC to handset, speed >

50KB/S)

2WM2

WM2.1.3蓝牙2.0+EDR数据传输测

试

(Date Transmit Test,

BT2.0+EDR)

●将蓝牙收发器连接电脑(Connect BT R/T device to

PC)

●在无障碍物遮挡的情况下，保持手机和收发器10米距

离，测试数据传输(Test distance between handset &

BT R/T device = 10m. There is no block thing between

handset & BT R/T device)

●传输至少5MB的数据，计算传输速度(Transfer data

size > 5MB, record transfer time then we get the

speed)

●理论传输速度：268KB/S (max)

●从PC传送文件至手机存储卡，速度大于100KB/

秒(Transfer data from PC to storage card in

handset, speed > 100KB/S)

●从手机存储卡传送文件至PC，速度大于100KB/

秒(Transfer data from storage card in handset to

PC, speed > 100KB/S)

2WM2

WM2.1.4蓝牙功能传输距离测试

(BT Performance Test)

●使用I-MOBILE BHS-303蓝牙耳机(Use I-Mobile BHS-

303 bluetooth headset)

●通过蓝牙耳机播放MP3，蓝牙耳机和手机天线距离至

少10米，允许蓝牙耳机天线和手机蓝牙天线正对

(Listen to MP3 via BT headset, at least 10m far away

from handset. BT headset antenna faces to handset

BT antenna directly was permitted)

●通过蓝牙耳机拨打座机，蓝牙耳机和手机天线距离至

少10米，允许蓝牙耳机天线和手机蓝牙天线正对

(Call to a telephone via BT headset, at least 10m far

away from handset. BT headset antenna faces to

handset BT antenna directly was permitted)

●通过蓝牙耳机听到的音乐清晰流畅，无断续

(Smooth & clear audio signal can be received by

BT headset)

●通过蓝牙耳机通话，双方声音清晰流畅，无断续

(Smooth & clear voice signal can be received

and transmited by BT headset)

2NA

WM2.1.5蓝牙功能用户使用测试

(BT Customer Test)

●使用I-MOBILE BHS-303蓝牙耳机(Use I-Mobile BHS-

303 bluetooth headset)

●将蓝牙耳机挂在右耳(Put the BT headset on right ear)

●将手机以不同方向放入左边裤兜(Put the phone in left

pocket, different direction)

●测试MP3播放及同座机的语音通话(Music Play via BT

headset Test & Call to a telephone via BT headset

Test)

●通过蓝牙耳机听到的音乐清晰流畅，无断续

(Smooth & clear audio signal can be received by

BT headset)

●通过蓝牙耳机通话，双方声音清晰流畅，无断续

(Smooth & clear voice signal can be received

and transmited by BT headset)

2NA

WM2.2蓝牙功能电流测试

(BT Current Test)

对蓝牙各项电流指标进行测试(BT Current Test)

如无特殊要求，满足赛龙公司标准

(Abide Cellon standard if no more special

requirements)

2

On

Going

WM2.2.1蓝牙数据传输电流测试(BT

Data Transmit Current Test)●将供电电源调到VbatNom(Vbat = VbatNom)

●飞行模式或者使用测试卡，连上综测仪，Paging9(Flig

ht Mode Or communicated to test set with test card,

Paging = 9)

●打开蓝牙，和另外一蓝牙设备建立连接，传输数据，

当屏熄灭时，开始测试传输数据时的电流(Transmit file

to another BT device. Record current when LCD BL

off)

一般来说，如无特殊情况，请遵从以下标准

(Generally, please abide standard below if there

were no more requirements & special

applications)

≤100mA

2WM2

WM2.2.2开启蓝牙后，待机电流测试

(Sleep Current Test when BT

Actived)

●手机已经通过2.1(2.4)或者3.1(3.4)或者4.1测试(Fisrtly

, handset should pass test item 2.1(2.4) or 3.1(3.4) or

4.1)

●将供电电源调到VbatNom(Vbat = VbatNom)

●开启蓝牙后，测试手机待机电流(Handset sleep

current test with BT ON)

一般来说，如无特殊情况，请遵从以下标准

(Generally, please abide standard below if there

were no more requirements & special

applications)

≤ 3mA

2WM2

WM2.2.3连接蓝牙耳机后，待机电流测

试

(Sleep Current Test when

Connect to BT Headset)

●手机已经通过2.1或者3.1或者4.1测试(Fisrtly, handset

should pass test item 2.1 or 3.1 or 4.1))

●将供电电源调到VbatNom(Vbat = VbatNom)

●开启蓝牙，连接蓝牙耳机后，测试手机待机电流(Han

dset sleep current test with BT headset connection)

一般来说，如无特殊情况，请遵从以下标准

(Generally, please abide standard below if there

were no more requirements & special

applications)

≤ 3mA

2WM2

WM2.2.4操作蓝牙，然后关闭蓝牙，待

机电流测试

(Sleep Current Test After BT

operated & Closed)

●手机已经通过待机电流测试(Fisrtly, handset should

pass CT Test)

●将供电电源调到VbatNom(Vbat = VbatNom)

●开启蓝牙，然后关闭蓝牙，测试手机待机电流(Hands

et sleep current test after achieve process below: BT

ON → BT OFF)

待机底电流不超过CTx测试结果(Sleep current

should be no more than test result of CTx)

2WM2

WM3.3蓝牙极限环境下工作测试

(BT Test under Extremity

Environment)

在高低温环境下，对蓝牙基本功能进行测试(BT

function Test Under Extremity Environment)

测试中和测试后，蓝牙功能正常(During & After

test, BT function should be OK)

2

On

Going

WM3.3.1蓝牙极限环境下通话测试

(BT Communication Test

under Extremity

Environment)

●环境温度(Environment temperature: TempLow &

TempHigh)

●待温度稳定后，将手机放入温箱，蓝牙耳机置于箱外

，保持通话至少2个小时(Start test when test set was

stable. Put handset into temperature box, BT headset

outside of the temperature box. Make BT call at least

for 2 hours)

●每隔1小时，检查一次蓝牙通话情况(Check handset

BT communication status every 1 hour)

测试中和测试后，手机蓝牙通话正常(During &

After test, handset BT communication should be

OK)

2NA

WM3.3.1蓝牙极限环境下数据传输

测试

(BT File Transfer Test

under Extremity

Environment)

●环境温度(Environment temperature: TempLow &

TempHigh)

●待温度稳定后，将手机放入温箱至少2个小时(Start

test when test set was stable. Put handset into

temperature box at least for 2 hours)

●每隔1小时，检查一次蓝牙传输速度情况(Check

handset BT file transfer speed every 1 hour)

测试中和测试后，手机蓝牙传输速度正常(During

& After test, handset BT file transfer speed

should be OK)

2NA

WM3.1模拟电视测试(ATV Test)对模拟电视功能、性能测试(ATV Function &

Performance Test)

功能、性能正常(Function & Performance should

be OK)

2

On

Going

WM3.1.1模拟电视功能测试(ATV

Function Test)测试模拟电视自动搜台、手动搜台、音量控制、音频外

放功能是否正常(Auto search; Manual search; Volume

Control; Loudness Speaker)

模拟电视功能正常(Function should be OK)2NA

WM3.1.2模拟电视传导性能测试(ATV

Conductive Performanc Test)●通过屏蔽线将手机电视天线馈点和测试设备连接(Con

nect Handset & ATV test set via shielding cable)

●选择合适的制式，开始测试(Setting correct signal

type, start test)

●VHF1和VHF2波段，每个频道都要测试(Every

channel should be tested during VHF1 & VHF2 band)

●UHF波段，可以每隔50MHz测一个频道，抽查一些没

有测试的频道(Test channels with 50MHz gap was

permitted. Please random check some channels wihch

did not test)

一般来说，如无特殊情况，请遵从以下标准

(Generally, please abide standard below if there

were no more requirements & special

applications)

≤ -90dbm

2WM3

[传导性能仅做参考；关键是辐射性能要好，

不会比对比机差]

WM3.1.3模拟电视辐射性能测试(ATV

Radiation Performanc Test)对比样机(Benchmark): ？？？

●在正常信号和弱信号下，自动搜台的能力测试

(auto search ability under normal & bad radio signal)

●在正常信号和弱信号下，模拟电视性能效果对比测试(

ATV performance under normal and bad radio signal)

●在弱信号下，按键和刷屏时，ATV是否有明显噪音("Cl

ick" noise under bad radio signal when key_press &

refresh LCD)

●如无特殊要求，自动搜台的能力不会比对比机差

(auto search ability no less than benchmark)

●如无特殊要求，模拟电视性能效果不会比对比机

差(ATV Performance no bad than benchmark)

●弱信号下按键、刷屏时，无明显噪音(No

abvious noise)

2WM3

WM3.2模拟电视电流测试

(ATV Current Test)

对模拟电视各项电流指标进行测试(BT Current Test)

如无特殊要求，满足赛龙公司标准

(Abide Cellon standard if no more special

requirements)

2

On

Going

WM3.2.1模拟电视工作电流测试，耳机

模式

(ATV Function Current Test,

Headset mode)

●音频参数调整完成，或使用赛龙默认音频参数(Audio

parameters adjustment finished or set Cellon default

audio parameters)

●将供电电源调到VbatNom(Vbat = VbatNom)

●飞行模式或者使用测试卡，连上综测仪，Paging9(Flig

ht Mode Or communicated to test set with test card,

Paging = 9)

●插入耳机，开启模拟电视功能，屏背光最亮，最大音

量正常播放，开始测试，每次测试时间2分钟(With

headset, LCD BL Level = Max. Play ATV with max

volume. Every test lasts for 2mins)

一般来说，如无特殊情况，请遵从以下标准

(Generally, please abide standard below if there

were no more requirements & special

applications)

≤ 360mA

2WM3

WM3.2.2模拟电视工作电流测试，外放

模式

(ATV Function Current Test,

Loudness Speaker)

●音频参数调整完成，或使用赛龙默认音频参数(Audio

parameters adjustment finished or set Cellon default

audio parameters)

●将供电电源调到VbatNom(Vbat = VbatNom)

●飞行模式或者使用测试卡，连上综测仪，Paging9(Flig

ht Mode Or communicated to test set with test card,

Paging = 9)

●插入耳机，开启模拟电视功能，屏背光最亮，最大音

量正常外放，开始测试，每次测试时间2分钟(Loudness

mode, LCD BL Level = Max. Play ATV with max

volume. Every test lasts for 2mins)

●此项测试结果作为参考(5.2.2 test value just for

reference)

●一般来说，如无特殊情况，请遵从以下标准

(Generally, please abide standard below if there

were no more requirements & special

applications)

≤ 430mA

2WM3

WM3.2.3模拟电视关闭后，待机电流测

试

(Sleep Current Test when ATV

Closed)

●手机已经通过待机电流测试(Fisrtly, handset should

pass CT Test)

●将供电电源调到VbatNom(Vbat = VbatNom)

●按照以下流程操作：开启模拟电视→自动搜台→

选定某台→正常收看→关闭模拟电视→

测试待机电流(Please operate phone according to

process: Enable ATV → Auto Search → Selete One

Channel → ATV Play → Disable ATV → Sleep Current

Test)

待机底电流不超过CTx测试结果(Sleep current

should be no more than test result of CTx)

2NA

WM3.3模拟电视极限环境下连续

播放测试

(ATV Continuate Play

Test under Extremity

Environment)

在高低温环境下，模拟电视连续播放测试

(ATV Continuate Play Test under Extremity

Environment)

测试中和测试后，模拟电视功能正常(During &

After test, ATV Play function should be OK)

2

On

Going

WM3.3.1模拟电视极限环境下连续播放

测试

(ATV Continuate Play Test

under Extremity Environment)

●环境温度(Environment temperature: TempLow &

TempHigh)

●一台带耳机，一台不带耳机(1pcs handset with

headset, 1pcs handset without headset)

●待温度稳定后，模拟电视连续播放2个小时(ATV

continuate play for 2 hours for each temperature)

●每隔1小时，检查一次模拟电视的工作情况(Check

ATV play every 1 hour)

测试中和测试后，模拟电视功能正常(During &

After test, ATV Play function should be OK)

2NA