模具英语大全.doc
punch冲头
insert入块(嵌入件)
deburring punch压毛边冲子
groove punch压线冲子
stamped punch字模冲子
round punch圆冲子
special shape punch异形冲子
bending block折刀
roller滚轴
baffle plate挡块
located block定位块
supporting block for location
定位支承块
air cushion plate气垫板
air-cushion eject-rod气垫顶杆
trimming punch切边冲子
stiffening rib punch = stinger 加强筋冲子ribbon punch压筋冲子
reel-stretch punch卷圆压平冲子
guide plate定位板
sliding block滑块
sliding dowel block滑块固定块
active plate活动板
lower sliding plate下滑块板
upper holder block上压块
upper mid plate上中间板
spring box弹簧箱
spring-box eject-rod弹簧箱顶杆
spring-box eject-plate弹簧箱顶板
bushing bolck衬套
cover plate盖板
guide pad导料块
top plate上托板（顶板）
top block上垫脚
punch set上模座
punch pad上垫板
punch holder上夹板
stripper pad脱料背板
up stripper上脱料板
male die公模(凸模)
feature die公母模
female die母模(凹模)
upper plate上模板
lower plate下模板
die pad下垫板
die holder下夹板
die set下模座
bottom block下垫脚
bottom plate下托板(底板) stripping plate内外打(脱料板) outer stripper外脱料板
inner stripper内脱料板
lower stripper下脱料板
plain die简易模
pierce die冲孔模
forming die成型模
progressive die连续模
gang dies复合模
shearing die剪边模
riveting die铆合模
pierce冲孔
forming成型(抽凸,冲凸)
draw hole抽孔
bending折弯
trim切边
emboss凸点
dome凸圆
semi-shearing半剪
stamp mark冲记号
deburr or coin压毛边
punch riveting冲压铆合
side stretch侧冲压平
reel stretch卷圆压平
groove压线
blanking下料
stamp letter冲字(料号) shearing剪断
tick-mark nearside正面压印tick-mark farside反面压印extension dwg展开图procedure dwg工程图
die structure dwg模具结构图material材质
material thickness料片厚度factor系数
upward向上
downward向下
press specification冲床规格die height range适用模高
die height闭模高度
burr毛边
gap间隙
weight重量
total wt.总重量
punch wt.上模重量
compre sion molding压缩成型flash mold溢流式模具
plsitive mold挤压式模具
split mold分割式模具
cavity型控母模
core模心公模
taper锥拔
leather cloak仿皮革
shiver饰纹
flow mark流痕
welding mark溶合痕
post screw insert螺纹套筒埋值self tapping screw自攻螺丝striper plate脱料板
piston活塞
cylinder汽缸套
chip细碎物
handle mold手持式模具
encapsulation molding低压封装成型、射出成型用模具two plate两极式（模具）
well type蓄料井
insulated runner绝缘浇道方式
hot runner热浇道
runner plat浇道模块
valve gate阀门浇口
band heater环带状的电热器
spindle阀针
spear head刨尖头
slag well冷料井
cold slag冷料渣
air vent排气道
welding line熔合痕
eject pin顶出针
knock pin顶出销
return pin回位销反顶针
sleave套筒
stripper plate脱料板
insert core放置入子
runner stripper plate浇道脱料板
guide pin导销
eject rod (bar)（成型机）顶业捧
subzero深冷处理
three plate三极式模具
runner system浇道系统
stress crack应力电裂
orientation定向
sprue gate射料浇口，直浇口
nozzle射嘴
sprue lock pin料头钩销(拉料杆)
slag well冷料井
side gate侧浇口
edge gate侧缘浇口
tab gate搭接浇口
film gate薄膜浇口
flash gate闸门浇口
slit gate缝隙浇口
fan gate扇形浇口
dish gate因盘形浇口
diaphragm gate隔膜浇口
ring gate环形浇口
subarine gate潜入式浇口
tunnel gate隧道式浇口
pin gate针点浇口
Runner less无浇道
(sprue less)无射料管方式
long nozzle延长喷嘴方式
sprue浇口;溶渣
landed plunger mold 有肩柱塞式模具
burnishing die 挤光模 landed positive mold 有肩全压式模具button die 镶入式圆形凹模 loading shoe mold 料套式模具
center-gated mold 中心浇口式模具 loose detail mold 活零件模具chill mold 冷硬用铸模 loose mold 活动式模具
clod hobbing 冷挤压制模 louvering die 百叶窗冲切模
composite dies 复合模具 manifold die 分歧管模具
counter punch 反凸模 modular mold 组合式模具
double stack mold 双层模具 multi-cavity mold 多模穴模具electroformed mold 电铸成形模 multi-gate mold 复式浇口模具expander die 扩径模 offswt bending die 双折冷弯模具
extrusion die 挤出模 palletizing die 叠层模
family mold 反套制品模具 plaster mold 石膏模
blank through dies 漏件式落料模 porous mold 通气性模具duplicated cavity plate 复板模 positive mold 全压式模具fantail die 扇尾形模具 pressure die 压紧模
fishtail die 鱼尾形模具 profile die 轮廓模
flash mold 溢料式模具 progressive die 顺序模
gypsum mold 石膏铸模 protable mold 手提式模具
hot-runner mold 热流道模具 prototype mold 雏形试验模具
ingot mold 钢锭模 punching die 落料模
lancing die 切口模 raising(embossing) 压花起伏成形
re-entrant mold 倒角式模具 sectional die 拼合模
runless injection mold 无流道冷料模具 sectional die 对合模具
segment mold 组合模 semi-positive mold 半全压式模具
shaper 定型模套 single cavity mold 单腔模具
solid forging die 整体锻模 split forging die 拼合锻模
split mold 双并式模具 sprueless mold 无注道残料模具
squeezing die 挤压模 stretch form die 拉伸成形模
sweeping mold 平刮铸模 swing die 振动模具
three plates mold 三片式模具 trimming die 切边模
unit mold 单元式模具 universal mold 通用模具
unscrewing mold 退扣式模具 yoke type die 轭型模
padding block垫块
stepping bar垫条
upper die base上模座
lower die base下模座
upper supporting blank上承板
upper padding plate blank上垫板
spare dies模具备品
spring 弹簧
bolt螺栓
document folder活页夹
file folder资料夹
to put file in order整理资料
spare tools location手工备品仓
first count初盘人
first check初盘复棹人
second count 复盘人
second check复盘复核人
equipment设备
waste materials废料
work in progress product在制品
casing = containerazation装箱
quantity of physical invetory second count 复盘点数量
quantity of customs count
会计师盘,点数量
the first page第一联
filed by accounting department for reference会计部存查
end-user/using unit(department)使用单位
summary of year-end physical inventory bills
年终盘点截止单据汇总表
bill name单据名称
This sheet and physical inventory list will be sent to accounting department together (Those of NHK will be sent to financial department)
本表请与盘点清册一起送会计部－(NHK厂区送财会部)
Application status records of year-end physical inventory List and physical inventory card 年终盘点卡与清册使用－状况明细表
blank and waste sheet NO.
空白与作废单号
plate电镀
mold成型
material for engineering mold testing工程试模材料
not included in physical inventory不列入盘点
sample样品
incoming material to be inspected进货待验
description品名
steel/rolled steel钢材
material statistics sheet
物料统计明细表
meeting minutes会议记录
meeting type 会别
distribution department分发单位
location地点
chairman主席
present members出席人员
subject主题
conclusion结论
decision items决议事项
responsible department负责单位
pre-fixed finishing date预定完成日
approved by / checked by / prepared by核准/审核/承办
PCE assembly production schedule sheet
PCE组装厂生产排配表
model机钟
work order工令
revision版次
remark备注
production control confirmation生产确认
checked by初审
approved by核准
department部门
stock age analysis sheet
库存货龄分析表
on-hand inventory现有库存
available material良品可使用
obsolete material良品已呆滞
to be inspected or reworked
待验或重工
total合计
cause description原因说明
part number/ P/N 料号
type形态
item/group/class类别
quality品质
prepared by制表
notes说明
year-end physical inventory difference analysis sheet
年终盘点差异分析表
physical inventory盘点数量
physical count quantity帐面数量
difference quantity差异量
cause analysis原因分析
raw materials原料
materials物料
finished product成品
semi-finished product半成品
packing materials包材
good product/accepted goods/ accepted parts/good parts良品defective product/non-good parts不良品
disposed goods处理品
warehouse/hub仓库
on way location在途仓
oversea location海外仓
spare parts physical inventory list备品盘点清单
spare molds location模具备品仓
skid/pallet栈板
tox machine自铆机
wire EDM线割
EDM放电机
coil stock卷料
sheet stock片料
tolerance工差
score=groove压线
cam block滑块
pilot导正筒
trim剪外边
pierce剪内边
drag form压锻差
pocket for the punch head挂钩槽
slug hole废料孔
feature die公母模
expansion dwg展开图
radius半径
shim(wedge)楔子
torch-flame cut火焰切割
set screw止付螺丝
form block折刀
stop pin定位销
round pierce punch=die button圆冲子
shape punch=die insert异形子
stock locater block定位块
under cut=scrap chopper清角
active plate活动板
accurate die casting 精密压铸 powder forming 粉末成形calendaring molding 压延成形 powder metal forging 粉末锻造
cold chamber die casting 冷式压铸 precision forging 精密锻造
cold forging 冷锻 press forging 冲锻
compacting molding 粉末压出成形 rocking die forging 摇动锻造
compound molding 复合成形 rotary forging 回转锻造
compression molding 压缩成形 rotational molding 离心成形
dip mold 浸渍成形 rubber molding 橡胶成形
encapsulation molding 注入成形 sand mold casting 砂模铸造
extrusion molding 挤出成形 shell casting 壳模铸造
foam forming ?泡成形 sinter forging 烧结锻造
forging roll 轧锻 six sides forging 六面锻造
gravity casting 重力铸造 slush molding 凝塑成形
hollow(blow) molding 中空(吹出)成形 squeeze casting 高压铸造
hot chamber die casting 热室压铸 swaging 挤锻
hot forging 热锻 transfer molding 转送成形
injection molding 射出成形 warm forging 温锻
investment casting 精密铸造 matched die method 对模成形法
laminating method 被覆淋膜成形 low pressure casting 低压铸造
lost wax casting 脱蜡铸造 matched mould thermal forming 对模热成形模
aberration 色差 atomization ?化
bank mark ?料纹 bite 咬入
blacking hole 涂料孔(铸疵) blacking scab 涂料疤
blister 起泡 blooming 起霜
blow hole 破孔 blushing 泛白
body wrinkle 侧壁皱纹 breaking-in 冒口带肉
bubble 膜泡 burn mark 糊斑
burr 毛边 camber 翘曲
cell 气泡 center buckle 表面中部波皱
check 细裂痕 checking 龟裂
chipping 修整表面缺陷 clamp-off 铸件凹痕
collapse 塌陷 color mottle 色斑
corrosion 腐蚀 crack 裂痕
crazing 碎裂 crazing 龟裂
deformation 变形 edge 切边碎片
edge crack 裂边 fading 退色
filler speak 填充料斑 fissure 裂纹
flange wrinkle 凸缘起皱 flaw 刮伤
flow mark 流痕 galling 毛边
glazing 光滑 gloss 光泽
grease pits 污斑 grinding defect 磨痕
haircrack 发裂 haze 雾度
incrustation 水锈 indentation 压痕
internal porosity 内部气孔 mismatch 偏模
mottle 斑点 necking 缩颈
nick 割痕 orange peel 橘皮状表面缺陷
overflow 溢流 peeling 剥离
pit 坑 pitting corrosion 点状腐蚀
plate mark 模板印痕 pock 麻点
pock mark 痘斑 resin streak 树脂流纹
resin wear 树脂脱落 riding 凹陷
sagging 松垂 saponification 皂化
scar 疤痕 scrap 废料
scrap jam 废料阻塞 scratch 刮伤/划痕
scuffing 深冲表面划伤 seam 裂痕
shock line 模口挤痕 short shot 充填不足shrinkage pool 凹孔 sink mark 凹痕
skin inclusion 表皮折叠 straightening 矫直streak 条状痕 surface check 表面裂痕
surface roughening 橘皮状表皮皱折 surging 波动sweat out 冒汗 torsion 扭曲
warpage 翘曲 waviness 波痕
webbing 熔塌 weld mark 焊痕
whitening 白化 wrinkle 皱纹
air vent vale 通气阀 anchor pin 锚梢
angular pin 角梢 baffle 调节阻板
angular pin 倾斜梢 baffle plate 折流档板
ball button 球塞套 ball plunger 定位球塞
ball slider 球塞滑块 binder plate 压板
blank holder 防皱压板 blanking die 落料冲头bolster 上下模板 bottom board 浇注底板
bolster 垫板 bottom plate 下固定板
bracket 托架 bumper block 缓冲块
buster 堵口 casting ladle 浇注包
casting lug 铸耳 cavity 模穴(模仁)
cavity retainer plate 模穴托板 center pin 中心梢
clamping block 锁定块 coil spring 螺旋弹簧
cold punched nut 冷冲螺母 cooling spiral 螺旋冷却栓
core 心型 core pin 心型梢
cotter 开口梢 cross 十字接头
cushion pin 缓冲梢 diaphragm gate 盘形浇口
die approach 模头料道 die bed 型底
die block 块形模体 die body 铸模座
die bush 合模衬套 die button 冲模母模
die clamper 夹模器 die fastener 模具固定用零件
die holder 母模固定板 die lip 模唇
die plate 冲模板 die set 冲压模座
direct gate 直接浇口 dog chuck 爪牙夹头
dowel 定位梢 dowel hole 导套孔
dowel pin 合模梢 dozzle 辅助浇口
dowel pin 定位梢 draft 拔模锥度
draw bead 张力调整杆 drive bearing 传动轴承
ejection pad 顶出衬垫 ejector 脱模器
ejector guide pin 顶出导梢 ejector leader busher 顶出导梢衬套ejector pad 顶出垫 ejector pin 顶出梢
ejector plate 顶出板 ejector rod 顶出杆
ejector sleeve 顶出衬套 ejector valve 顶出阀
eye bolt 环首螺栓 filling core 椿入蕊
film gate 薄膜形浇口 finger pin 指形梢
finish machined plate 角形模板 finish machined round plate 圆形模板fixed bolster plate 固定侧模板 flanged pin 带凸缘?
flash gate 毛边形浇口 flask 上箱
floating punch 浮动冲头 gate 浇口
gate land 浇口面 gib 凹形拉紧?
goose neck 鹅颈管 guide bushing 引导衬套
guide pin 导梢 guide post 引导柱
guide plate 导板 guide rail 导轨
head punch 顶?冲头 headless punch 直柄冲头
heavily tapered solid 整体模蕊盒 hose nippler 管接头
impact damper 缓冲器 injection ram 压射柱塞
inlay busher 嵌入衬套 inner plunger 内柱塞
inner punch 内冲头 insert 嵌件
insert pin 嵌件梢 king pin 转向梢
king pin bush 主梢衬套 knockout bar 脱模杵
land 合模平坦面 land area 合模面
leader busher 导梢衬套 lifting pin 起模顶?
lining 内衬 locating center punch 定位中心冲头
locating pilot pin 定位导梢 locating ring 定位环
lock block 压块 locking block 定位块
locking plate 定位板 loose bush 活动衬套
making die 打印冲子 manifold block 歧管档块
master plate 靠模样板 match plate 分型板
mold base 塑胶模座 mold clamp 铸模紧固夹
mold platen 模用板 moving bolster 换模保持装置
moving bolster plate 可动侧模板 one piece casting 整体铸件parallel block 平行垫块 paring line 分模线
parting lock set 合模定位器 pass guide 穴型导板
peened head punch 镶入式冲头 pilot pin 导?
pin gate 针尖浇口 plate 衬板
pre extrusion punch 顶挤冲头 punch 冲头
puncher 推杆 pusher pin 衬套梢
rack 机架 rapping rod 起模杆
re-entrant mold 凹入模 retainer pin 嵌件梢
retainer plate 托料板 return pin 回位梢
riding stripper 浮动脱模器 ring gate 环型浇口
roller 滚筒 runner 流道
runner ejector set 流道顶出器 runner lock pin 流道拉梢screw plug 头塞 set screw 固定螺丝
shedder 脱模装置 shim 分隔片
shoe 模座之上下模板 shoot 流道
shoulder bolt 肩部螺丝 skeleton 骨架
slag riser 冒渣口 slide(slide core) 滑块
slip joint 滑配接头 spacer block 间隔块
spacer ring 间隔环 spider 模蕊支架
spindle 主轴 sprue 注道
sprue bushing 注道衬套 sprue bushing guide 注道导套
sprue lock bushing 注道定位衬套 sprue puller 注道拉料? spue line 合模线 square key 方键
square nut 方螺帽 square thread 方螺纹
stop collar 限位套 stop pin 止动梢
stop ring 止动环 stopper 定位停止梢
straight pin 圆柱? stripper bolt 脱料螺栓
stripper bushing 脱模衬套 stripper plate 剥料板
stroke end block 行程止梢 submarine gate 潜入式浇口
support pillar 支撑支柱/顶出支柱 support pin 支撑梢
supporting plate 托板 sweep templete 造模刮板
tab gate 辅助浇口 taper key 推拔键
taper pin 拔锥梢/锥形梢 teeming 浇注
three start screw 三条螺纹 thrust pin 推力销
tie bar 拉杵 tunnel gate 隧道形浇口
vent 通气孔 wortle plate 拉丝模板
1 GB/T 2-1985 紧固件外螺纹零件的末端 Fasteners--Ends of parts with external thread
2 GB/T 8-1988 方头螺栓 C级 Square head bolts--Product grade C
3 GB/T 10-1988 沉头方颈螺栓 Flat countersunk square neck bolts
4 GB/T 11-1988 沉头带榫螺栓 Flat countersunk nib bolts
5 GB/T 12-1988 半圆头方颈螺栓 Cup head square neck bolts
6 GB/T 13-1988 半圆头带榫螺栓 Cup head nib bolts
7 GB/T 15-1988 大半圆头带榫螺栓 Cup head nib bolts with large head
8 GB/T 22-1976 小六角头导颈螺栓 Bolts, small hexagon head with fit neck
9 GB/T 23-1976 小六角头螺杆带孔螺栓 Bolts, small hexagon head with hole through the shank
10 GB/T 24-1976 小六角头螺杆带孔导颈螺栓 Bolts, small hexagon head with fit neck and hole through the shank
11 GB/T 25-1976 小六角头头部带孔螺栓 Bolts, small hexagon head with holes through the head
12 GB/T 26-1976 小六角头头部带孔导颈螺栓 Bolts, small hexagon head with fit neck and holes through the head
13 GB/T 27-1988 六角头铰制孔用螺栓 A和B级 Hexagon fit bolts--Product grade A and B
14 GB/T 28-1988 六角头螺杆带孔铰制孔用螺栓 A和B级 Hexagon fit bolts with Split pin hole on shank--Product grade A and B
15 GB/T 29.1-1988 六角头头部带槽螺栓 A和B级 Hexagon bolts with slot on head--Product grade A and B
16 GB/T 29.2-1988 十字槽凹穴六角头螺栓 Cross recessed hexagon bolts with indentation
17 GB/T 31.1-1988 六角头螺杆带孔螺栓 A和B级 Hexagon bolts with split
pin hole on shank--Product grade A and B
18 GB/T 31.2-1988 六角头螺杆带孔螺栓细杆 B级 Hexagon bolts with split pin hole on shank--Reduced shank--Product grade B
19 GB/T 31.3-1988 六角头螺杆带孔螺栓细牙 A和B级 Hexagon bolts with split pin hole on shank--Fine pitch thread--Product grade A and B
20 GB/T 32.1-1988 六角头头部带孔螺栓 A和B级 Hexagon bolts with wire holes on head--Product grade A and B 21 GB/T 32.2-1988 六角头头部带孔螺栓细杆 B级 Hexagon bolts with wire holes on head--Reduced
shank--Product grade B
22 GB/T 32.3-1988 六角头头部带孔螺栓细牙 A和B级 Hexagon bolts with wire holes on head--Fine pitch thread--Product grade A and B
23 GB/T 35-1988 小方头螺栓 B级 Square head bolts with small
head--Product grade B
24 GB/T 37-1988 T型槽用螺栓 Bolts for T-Slot
25 GB/T 38-1976 螺栓技术条件 Bolts--Technical requirements
26 GB/T 39-1988 方螺母 C级 Square nuts--Product grade C
27 GB/T 41-1986 1 型六角螺母 C 级 Hexagon nuts--Style 1--Product grad C
28 GB/T 56-1988 六角厚螺母 Hexagon thick nuts
29 GB/T 61-1976 螺母技术条件 Nuts--Technical requirements
30 GB/T 62-1988 蝶形螺母 Wing nuts
31 GB/T 63-1988 环形螺母 Lifting nuts
32 GB/T 65-1985 开槽圆柱头螺钉 Slotted cheese head screws
33 GB/T 67-1985 开槽盘头螺钉 Slotted pan head screws
34 GB/T 68-1985 开槽沉头螺钉 Slotted countersunk head screws
35 GB/T 69-1985 开槽半沉头螺钉 Slotted raised countersunk head screws
36 GB/T 70-1985 内六角圆柱头螺钉 Hexagon socket cap head screws
37 GB/T 71-1985 开槽锥端紧定螺钉 Slotted set screws with cone point
38 GB/T 72-1988 开槽锥端定位螺钉 Slotted set screws with cone point
39 GB/T 73-1985 开槽平端紧定螺钉 Slotted set screws with flat point
40 GB/T 74-1985 开槽凹端紧定螺钉 Slotted set screws with cup point
41 GB/T 75-1985 开槽长圆柱端紧定螺钉 Slotted set screws withlong dog point
42 GB/T 77-1985 内六角平端紧定螺钉 Hexagon socket set screws with flat point
43 GB/T 78-1985 内六角锥端紧定螺钉 Hexagon socket set screws with cone point
44 GB/T 79-1985 内六角圆柱端紧定螺钉 Hexagon socket set screws with dog point
45 GB/T 80-1985 内六角凹端紧定螺钉 Hexagon socket set screws with cup
point
46 GB/T 83-1988 方头长圆柱球面端紧定螺钉 Square set screws with long dog point and rounded end
47 GB/T 84-1988 方头凹端紧定螺钉 Square set screws with cup point
48 GB/T 85-1988 方头长圆柱端紧定螺钉 Square set screws with long dog point
49 GB/T 86-1988 方头短圆柱锥端紧定螺钉 Square set screws with short dog point and cone end
50 GB/T 89-1976 螺钉技术条件 Screws--Technical requirements
51 GB/T 90-1985 紧固件验收检查、标志与包装 Acceptance
inspection,marking and packaging of fasteners
52 GB/T 91-1986 开口销 Split pins
53 GB/T 93-1987 标准型弹簧垫圈 Single coil spring lock washers--Normal type
54 GB/T 94.1-1987 弹性垫圈技术条件弹簧垫圈 Specifications for spring washers--Single coil spring lock washers
55 GB/T 94.2-1987 弹性垫圈技术条件齿形、锯齿锁紧垫圈 Specifications for spring washers--Toothed lock and serrated lock washers
56 GB/T 94.3-1987 弹性垫圈技术条件鞍形、波形弹性垫圈 Specifications for spring washers--Curved and wave spring washers
57 GB/T 95-1985 平垫圈-C级 Plain washers--Product grade C
58 GB/T 272-1993 滚动轴承代号方法 Rolling bearing--Identification code
59 GB/T 273.1-1987 滚动轴承圆锥滚子轴承外形尺寸方案 Rolling bearings Tapered roller bearings--Boundary dimensions
60 GB/T 273.3-1988 滚动轴承向心轴承外形尺寸方案 Rolling bearings Radial bearings-Boundary dimensions
61 GB/T 274-1991 滚动轴承装配倒角极限 Rolling bearing chamfer dimension limits
62 GB/T 275-1993 滚动轴承与轴和外壳的配合 Shaft and housing fits for rolling bearings
63 GB/T 276-1994 滚动轴承深沟球轴承外形尺寸 Rolling bearings--Deep groove ball bearings--Boundary dimensions
64 GB/T 280-1964 带毡封圈的单列向心球轴承结构型式和基本尺寸 Rolling bearings--Single-row radial ball bearings withfelt seals--Types and basic dimensions
65 GB/T 281-1994 滚动轴承调心球轴承外形尺寸 Rolling
bearings--Self-aligning ball bearings--Boundary dimensions
66 GB/T 283-1994 滚动轴承圆柱滚子轴承外形尺寸 Rolling
bearings--Cylindrical roller bearings-Boundary dimensions
67 GB/T 285-1994 滚动轴承双列圆柱滚子轴承外形尺寸 Rolling
bearings--Double row cylindrical roller bearings-Boundary dimensions 68 GB/T 286-1964 双列向心球面滚子轴承结构型式和基本尺寸 Rolling bearings--Double -row radial spherical roller bearings--Types and basic dimensions
69 GB/T 288-1994 滚动轴承调心滚子轴承外形尺寸 Rolling
bearings--Self-aligning roller bearings-Boundary dimensions
70 GB/T 289-1964 滚针轴承结构型式和基本尺寸 Needle roller
bearings--Types and basic dimensions
71 GB/T 291-1964 螺旋滚子轴承结构型式和基本尺寸 Rolling bearings with helically wound cylindrical rollers--Types and basic dimensions
72 GB/T 292-1994 滚动轴承角接触球轴承外形尺寸 Rolling
bearings--Angular contact ball bearings--Boundary dimensions
73 GB/T 294-1994 滚动轴承三点和四点接触球轴承外形尺寸 Rolling bearings--Three point and four point contact ball bearings--Boundary dimensions
74 GB/T 296-1994 滚动轴承双列角接触球轴承外形尺寸 Rolling
bearings--Double row angular contact ball bearings--Boundary dimensions 75 GB/T 297-1994 滚动轴承圆锥滚子轴承外形尺寸 Rolling
bearings--Tapered roller bearings--Boundary dimensions
76 GB/T 299-1995 滚动轴承双列圆锥滚子轴承外形尺寸 Rolling
bearings--Metric double row tapered roller bearings--Boundary dimensions 77 GB/T 300-1995 滚动轴承四列圆锥滚子轴承外形尺寸 Rolling
bearings--Four row tapered roller bearings--Boundary dimensions
78 GB/T 301-1995 滚动轴承推力球轴承外形尺寸 Rolling bearings--Thrust ball bearings--Boundary dimensions
79 GB/T 304.1-1988 关节轴承分类 Spherical plain bearings
Classification
80 GB/T 304.2-1988 关节轴承代号方法 Spherical plain bearings Identification code
81 GB/T 304.3-1990 关节轴承配合 Spherical plain bearings-Fits
82 GB/T 304.9-1981 向心关节轴承技术条件 Spherical plain radial bearings, joint type--Technical requirements
83 GB/T 304.10-1989 关节轴承公差 Spherical plain bearings-Tolerances
84 GB/T 307.1-1994 滚动轴承向心轴承公差 Rolling bearings--Radial bearings--Tolerances
85 GB/T 307.2-1995 滚动轴承测量和检验的原则及方法 Rolling
bearings--Measuring and gauging principles and methods
86 GB/T 307.3-1996 滚动轴承通用技术规则 Rolling bearings--General technical regulations
87 GB/T 307.4-1994 滚动轴承推力球轴承公差 Rolling bearings--Thrust ball bearings--Tolerances
88 GB/T 308-1989 滚动轴承钢球 Rolling bearings-Steel balls
89 GB/T 309-1984 滚动轴承滚针 Rolling bearings--Needle rollers
90 GB/T 794-1993 加强半圆头方颈螺栓 Strengthened cap head square neck bolts
91 GB/T 798-1988 活节螺栓 Eye bolts
92 GB/T 799-1988 地脚螺栓 Eyelet bolts
93 GB/T 800-1988 沉头双榫螺栓 Flat countersunk double nib bolts
94 GB/T 802-1988 组合式盖形螺母 Acorn nuts
95 GB/T 804-1988 球面六角螺母 Hexagon nuts with raised face
96 GB/T 805-1988 扣紧螺母 Tight nuts
97 GB/T 806-1988 滚花高螺母 Knurled nut with collar
98 GB/T 807-1988 滚花薄螺母 Knurled nuts
99 GB/T 808-1988 小六角特扁细牙螺母 Small hexagon thin nuts-Fine pitch thread
100 GB/T 809-1988 嵌装圆螺母 Insert round nuts
101 GB/T 810-1988 小圆螺母 Small round nuts
102 GB/T 812-1988 圆螺母 Round nuts
103 GB/T 815-1988 端面带孔圆螺母 Round nuts with drilled holes in one face
104 GB/T 816-1988 侧面带孔圆螺母 Round nuts with set pin holes in side 105 GB/T 817-1988 带槽圆螺母 Slotted round nuts
106 GB/T 818-1985 十字槽盘头螺钉 Cross recessed pan head screws
107 GB/T 819-1985 十字槽沉头螺钉 Cross recessed countersunk head screws 108 GB/T 820-1985 十字槽半沉头螺钉 Cross recessed raised countersunk head screws
109 GB/T 821-1988 方头倒角端紧定螺钉 Square set screws with chamfered end
110 GB/T 822-1988 十字槽圆柱头螺钉 Cross recessed cheese head serews 111 GB/T 823-1988 十字槽小盘头螺钉 Cross recessed small pan head screws 112 GB/T 824-1976 圆柱头内花键螺钉 Screws,fluted socket head
113 GB/T 825-1988 吊环螺钉 Eyebolts
114 GB/T 827-1986 标牌铆钉 Rivets for name plate
115 GB/T 828-1988 开槽盘头定位螺钉 Slotted pan head set setscrews with dog point
116 GB/T 829-1988 开槽圆柱端定位螺钉 Slotted setscrews with dog point 117 GB/T 830-1988 开槽圆柱头轴位螺钉 Slotted cheese head screws with shoulder
118 GB/T 831-1988 开槽无头轴位螺钉 Slotted shoulder screws
119 GB/T 832-1988 开槽带孔球面圆柱头螺钉 Slotted capstan screws
120 GB/T 833-1988 开槽大圆柱头螺钉 Slotted large cheese head screws 121 GB/T 834-1988 滚花高头螺钉 Knurled thumb screws
122 GB/T 835-1988 滚花平头螺钉 Knurled screws
123 GB/T 836-1988 滚花小头螺钉 Knurled screws with small head
124 GB/T 837-1988 开槽盘头不脱出螺钉 Slotted pan head screws with waisted shank
125 GB/T 838-1988 六角头不脱出螺钉 Hexagon screws with waisted shank 126 GB/T 839-1988 滚花头不脱出螺钉 Knurled thumb screws with waisted shank
127 GB/T 840-1988 塑料滚花头螺钉 Plastic diamond knurlhead screws
128 GB/T 845-1985 十字槽盘头自攻螺钉 Cross recessed pan head tapping screws
129 GB/T 846-1985 十字槽沉头自攻螺钉 Cross recessed countersunk head tapping screws
130 GB/T 847-1985 十字槽半沉头自攻螺钉 Cross recessed raised countersunk head tapping screws
131 GB/T 848-1985 小垫圈--A级 Plain washers--Small series--Product grade A
132 GB/T 849-1988 球面垫圈 Weshers with ball face
133 GB/T 850-1988 锥面垫圈 Washers with cone face
134 GB/T 851-1988 开口垫圈 Washers with split
135 GB/T 852-1988 工字钢用方斜垫圈 Square taper washers for I section 136 GB/T 853-1988 槽钢用方斜垫圈 Square taper washers for slot section 137 GB/T 854-1988 单耳止动垫圈 Tab washers with long tab
138 GB/T 855-1988 双耳止动垫圈 Tab washers with long tab and wing
139 GB/T 856-1988 外舌止动垫圈 External tab washers
140 GB/T 858-1988 圆螺母用止动垫圈 Tab washers for round nut
141 GB/T 859-1987 轻型弹簧垫圈 Single coil spring lock washers,Light type
142 GB/T 860-1987 鞍形弹性垫圈 Curved spring washers
143 GB/T 861.1-1987 内齿锁紧垫圈 Lock washers internal teeth
144 GB/T 861.2-1987 内锯齿锁紧垫圈 Serrated lock washers internal teeth 145 GB/T 862.1-1987 外齿锁紧垫圈 Lock washers external teeth
146 GB/T 862.2-1987 外锯齿锁紧垫圈 Serrated lock washers external teeth
147 GB/T 863.1-1986 半圆头铆钉 (粗制) Round head rivets--Black
148 GB/T 863.2-1986 小半圆头铆钉 (粗制) Round head rivets with small head--Black
149 GB/T 864-1986 平锥头铆钉 (粗制) Cone head rivets--Black
150 GB/T 865-1986 沉头铆钉 (粗制) Countersunk head rivets-Black
plain die简易模
pierce die冲孔模
forming die成型模
progressive die连续模
gang dies复合模
shearing die剪边模
riveting die铆合模
pierce冲孔
forming成型(抽凸,冲凸)
draw hole抽孔
bending折弯
trim切边
emboss凸点
dome凸圆
semi-shearing半剪
stamp mark冲记号
deburr or coin压毛边
punch riveting冲压铆合
side stretch侧冲压平
reel stretch卷圆压平
groove压线
blanking下料
stamp letter冲字(料号)
shearing剪断
模具专业英文术语大全
模具英语专业术语 模具述语 一、入水：gate 进入位： gate location 水口形式：gate type 大水口：edge gate 细水口： pin-point gate 水口大小：gate size 转水口： switching runner/gate 唧嘴口径： sprue diameter 二、流道: runner 热流道： hot runner,hot manifold 热嘴冷流道: hot sprue/cold runner 唧嘴直流: direct sprue gate 圆形流道：round(full/half runner 流道电脑分析：mold flow analysis 流道平衡:runner balance 热嘴： hot sprue 热流道板：hot manifold 发热管：cartridge heater 探针: thermocouples 插头： connector plug 插座： connector socket 密封/封料： seal 三、运水：water line 喉塞：line lpug 喉管：tube 塑胶管：plastic tube 快速接头：jiffy quick connector plug/socker 四、模具零件： mold components 三板模：3-plate mold 二板模：2-plate mold 边钉/导边：leader pin/guide pin 边司/导套：bushing/guide bushing 中托司：shoulder guide bushing 中托边L：guide pin 顶针板：ejector retainner plate 托板： support plate 螺丝： screw 管钉：dowel pin 开模槽：ply bar scot 内模管位：core/cavity inter-lock 顶针： ejector pin 司筒：ejector sleeve 司筒针：ejector pin 推板：stripper plate 缩呵：movable core,return core core puller 扣机（尼龙拉勾）：nylon latch lock 斜顶：lifter 模胚（架）： mold base 上内模：cavity insert 下内模：core insert 行位（滑块）： slide 镶件：insert 压座/斜鸡：wedge 耐磨板/油板：wedge wear plate 压条：plate 撑头: support pillar 唧嘴： sprue bushing 挡板：stop plate 定位圈：locating ring 锁扣：latch 扣鸡：parting lock set 推杆：push bar 栓打螺丝：S.H.S.B 顶板：eracuretun 活动臂：lever arm 分流锥：spure sperader 水口司:bush 垃圾钉：stop pin 隔片：buffle 弹弓柱：spring rod 弹弓:die spring 中托司：ejector guide bush 中托边：ejector guide pin 镶针：pin 销子：dowel pin 波子弹弓：ball catch 喉塞: pipe plug
模具专业术语 英语对照
GLOSSARY A abrasive grinding 强力磨削 L3 abrasive[E'breisiv] a.磨料的, 研磨的 L2,3 absence ['AbsEns] n.. 不在，缺席 L17 accesssory[Ak'sesEri] n.附件 L10 accommodate[E'kCmEdeit] v. 适应 L5 accordingly[E'kC:diNli] adv.因此,从而,相应地 L7,13 accuracy['AkjurEsi] n精度,准确性 L1,3 actuate['Aktjueit] vt.开动(机器), 驱动 L8 adequate['Adikwit] a. 足够的 L13 adhesive[Ed'hi:siv] n. 粘合剂 L22 adjacent[E'dVeisnt] a. 邻近的 L13 adopt[E'dCpt] vt. 采用 L4 advance [Ed'vA:ns] n.进步 L7 advisable [Ed'vaizbl] adj. 可取的 L20 agitate['AdViteit] v. 摇动 L2 a large extent 很大程度 L4,13 algorithm ['Al^EriTEm] n. 算法 L6 align [E'lain] v 定位，调准 L17 alignment[E'lainmEnt] n. 校直 L11 all-too-frequent 频繁 L17 allowance[E'lEuens] n. 容差, 余量 L5 alternate['C:ltEnit]v.交替,轮流 L1 alternative[C:l'tE:nEtiv] n. 替换物 L3 alternatively[C:l'tE:nEtivli] ad. 做为选择, 也许 L5 aluminiun[7Alju'minjEm] n.铝 L2 ample['Ampl] adj. 充足的 L20 analysis [E'nAlEsis] n. 分析 L6 ancillary['AnsilEri] a.补助的, 副的 L4 angular ['A^julE] adj. 有角的 L20 annealing[E'li:liN] n.退火 L2 aperture ['ApEtFE] n.孔 L17 applied loads 作用力 L1 appropriate [E'prEuprieit] a. 适当的 L6,20 arc[a:k] n.弧, 弓形 L10 arise[E'raiz] vi. 出现, 发生 L21 arrange[E'reidV] v. 安排 L12 article['a:tikl] n.制品, 产品 L21 ascertain[7AsE'tein] vt. 确定, 查明 L1 assemble[E'sembl] vt.组装 L4 attitude ['Atitju:d] n 态度 L17 auxiliary [C:^'ziljEri]adj. 辅助的 L8 avoid[E'vCid] v.避免 L7 axis['Aksis] n.轴 L5 axle['Aksl] n.轮轴, 车轴 L1 B backup['bAk7Qp] n. 备份 L9 batch [bAtF] n 一批 L17 bearing['bZEriN] n.轴承,支座 L21 bed[bed] n. 床身 L5 behavior[bi'heivjE] n. 性能 L1 bench-work 钳工工作 L4 bend[bend] v.弯曲 L1 beneath[bi'ni:W] prep在···下 L4 bin [bin] n. 仓，料架 L19 blank [blANk] n. 坯料 L20 blank [blANk] v. 冲裁,落料 L17 blanking tool 落料模 L17 blast [blQst] n.一阵（风） L18 blemish['blemiF] n. 缺点, 污点 L13 bolster['bEulstE] n. 模座,垫板 L4,5 boost[bu:st] n. 推进 L9 boring['bC:riN] n.镗削, 镗孔 L4,5 bracket ['brAkit] n. 支架 L19 brass [brAs] n.黄铜 L2 break down 破坏 L1 breakage ['breikidV] n.破坏 L17 bridge piece L16 brine[brain] n. 盐水 L2 brittle['britl] adv.易碎的 L1 buffer [bQfE] n.缓冲器 L8 built-in 内装的 L9 bulging [bQldViN] n. 凸肚 L22 burr [bE:] n. 毛刺 L17 bush [buF] n. 衬套 L17 bush[buF]n. 衬套 L5 by far (修饰比较级, 最高级)···得 多, 最 L3 by means of 借助于 L5 C cabinet ['kAbinit] n.橱柜 L7 call upon 要求 L17 carbide['ka:baid] n.碳化物 L10 carburzing['ka:bjuretiN] n. 渗碳 L2 carriage['kAridV] n.拖板, 大拖板 L5 carry along 一起带走 L18 carry down over 从···上取下 L21 carry out 完成 L17 case hardening 表面硬化 L2 case[keis] n. 壳, 套 L2 cast steel 铸钢 L17 casting['ka:stiN] n. 铸造,铸件 L3 category['kAtE^Euri] n. 种类 L6,15 caution ['kC:FEn] n. 警告，警示 L17 cavity and core plates 凹模和凸模板 L11 cavity['kAviti] n.型腔, 腔, 洞 L4,10 centre-drilling 中心孔 L5 ceramic[si'rAmik] n.陶瓷制品 L3 chain doted line 点划线 L11 channel['tFAnl] n.通道, 信道 L8 characteristic[kArEktE'ristik] n.特性 L1 check[tFek] v.核算 L21 chip[tFip] n.切屑, 铁屑 L3
模具专业英语词汇大全
模具专业英语词汇 A abrasion n. 磨损 abrasion resistance n. 耐磨损性 abrasive n. 磨料 accelerator n. 促进剂 accuracy n. 准确性 accurate die casting 精密压铸 air trap 积风 acrylic n. 丙烯酸 /压克力 ì active plate 活动板 additive n. 添加剂 adhere v. 黏附 adhesion n. 黏合 adhesive n. 胶粘剂 air-cushion eject-rod 气垫顶杆 air cushion plate 气垫板 air entrapment n. 困气 anneal v. 退火 assemble v. 总成 B back pressure 背压 bismuth mold 铋铸模 baffle plate 挡块 barrel n. 机筒 /料筒 / bending block 折刀 bottom block 下垫脚 bottom plate 下托板(底板) bushing bolck 衬套 barrel temperature 料筒温度 blush 发 blank through dies 漏件式落料模 burnishi blow molding n. 吹塑成型 blow molding machine n. 吹塑机 brittle adj. 脆性 bubble n. 气泡 burr 毛刺 button d by-product n. 副产品 C calendering n. 压延 carbon steel n. 碳素钢 casting n. 铸造 catalyst n. 催化剂 cavity n. 型腔 chemical resistance n. 耐化学腐蚀性 chip v. 削 /凿
模具英语100句
如何用英文和老外检讨模具 (2008-1-16 08:50) 1．XXX！你现在有空吗，我可以问你一些问题吗？ Could I ask you some questions？May I ask you some questions (a question)? 2．请问此产品的面是否为外观面？表面做什么处理？是晒纹/抛光？ Can you tell me whether the surface of this part is a visible/esthetic one? What will we do for its surface? Texture or Polishing? 3．请问产品这个面可否加顶针或顶块？产品允许加扁顶针吗？ Does this part need an ejector pin or an ejector bar? Can we add an ejector blade? 4．这个产品的柱位我们打算做司筒。（或镶针）可以吗？ Can we add ejector sleeves or ejector pins in the boss of this part? 5．产品的这个位置有倒扣不能出模，我们打算做行位，在此面上会有分模线，你接受吗？There's an undercut at this position that can not be molded, we plan to make a slider for it. It will also have a parting line on this side, is that OK? 6．产品里面的这个位置我们打算做斜顶或内行位，有问题吗？ We will make the lifter and (inner) slider in this position, will that be a problem? 7．你提供的2D产品图与3D产品图不一致，请问以哪一个图面为准？ The 2D and 3D drawings you provided are not the same, could you advise which one is correct? 8．你提供的3D产品图有的地方没有出模角，有的地方胶位太厚，有的地方胶位太溥，这些产品问题我们可以自己修改吗？修改后会给交给你确认。 There is no draft angle in the 3D model, some areas are too thick, and some are too thin. Can we modify them by ourselves? We will send you the updated drawing for approval. 9．按你们提供的缩水率千分之五，这个模具的尺寸已经做到了模具图面要求。但注塑出来的产品不符合你们的产品图。请确认你们的材料的缩水率是否正确？ According to the shrinkage rate .005”, the mold has been done in the right dimension, but the part falls short to your part print(the actual dimensions are out of tolerances), are you sure the shrinkage is right?
模具专业英语——注塑模
Injection Mold Technical Terms 特克内克腾目思 （一）模具专业基本用词 Professional Terms Intensification Factor 增强比 Scientific molding 科学注塑英腾次分克深发克偷 塞音特菲克计数器counter康特 Specific Injection Pressure (Psi)特殊注塑压力 思呗色服克 1．塑料—plastic, resin瑞申油管：Oil pipe 尼龙--------nylon 2．样件—sample 调节板-------adjust plate 3．钢料—steel A板--------a plate 4．注塑机—injection machine, press 定位圈----locating ring 喽客厅令 5．产品—part, product, moulding 斜导柱-----angular pin 安给拉PIN 6．模具—mold, mould, tool B板--------- b plate A 简易模（样板模）—prototype mold B 量产用模具—production mold 7．三维造型（数模）—3D model, 滚珠导套-------ball ejector bush 8．二维产品图—2D part drawing 拽应扁顶针--------blade ejector pin 布累得 9．设计—design 低赛应下模板--------bottom clamping plate 抱腾 10．制造—manufacture, 上模型腔------cavity main insert 11．检验—check, 上模镶件------cavity sub insert 12．测量—measure, 妹试司筒针--------center pin 深特 13．修改—change, modify 下模型芯------core main insert 14．工程更改—engineer change 下模镶针------core pin 15．质量—quality 快乐体下模镶件------core sub insert 16．数量—quantity 宽体踢延迟顶针-------delay ejector pin 17．基准—datum, reference 拉杆限位钉--------distance bolt （二）如何解析2D 产品图？How to read 2D part drawing? 一．产品几何Geometry 顶距限位柱--------distance spacer 1．点—point 销钉-------dowel pin 2．线（边）—line, edge 顶块--------ejector bar 3．面face 顶板导套-----ejector leader pin A 侧面—side塞得 B表面—surface射飞思 C 外观面—appearance surface安皮尔思射飞思4．壁厚—wall thickness 我射克来思顶板导柱----ejector leader pin李德拼 5．加强筋（骨位）—rib 瑞布顶针-------ejector pin 6．孔—hole后顶针地板------ejector plate 7．细长的槽—slot 顶针面板-----ejector retain plate 瑞腾 8．柱位—boss 抱死顶棍------ejector rod
模具英语词汇表汇编
模具英语词汇表 A abrasive grinding 强力磨削abrasive['breisiv] a.磨料的, 研磨的 absence ['bs ns] n.. 不在，缺席accessory[k'ses ri] n.附件 accommodate['k m deit] v. 适应 accordingly['k:di li] adv.因此,从而,相应地
accuracy['kjur si] n精度,准确性 actuate['ktjueit] vt.开动(机器), 驱动 adequate['dikwit] a. 足够的adhesive[d'hi:siv] n. 粘合剂 adjacent['d eisnt] a. 邻近的 adopt['d pt] vt. 采纳advance [d'v:ns] n.进步advisable [d'vaizbl] adj. 可取的agitate['d iteit] v. 摇动 a large extent 专门大程度algorithm ['l ri m] n. 算法 align ['lain] v 定位，调准alignment['lainm nt] n. 校直 all-too-frequent 频繁allowance['l uens] n. 容差, 余量 alternate[':lt nit]v.交替,轮流 alternative[:l't:n tiv]
n. 替换物 alternatively[:l't:n t ivli] ad. 做为选择, 也许aluminum[lju'minj m] n.铝 ample['mpl] adj. 充足的analysis ['n l sis] n. 分析 ancillary['nsil ri] a.补助的, 副的 angular ['jul] adj. 有角的 annealing['li:li ] n.退火 aperture ['p t ] n.孔applied loads 作用力appropriate ['pr uprieit] a. 适当的 arc[a:k] n.弧, 弓形 arise['raiz] vi. 出现, 发生 arrange['reid] v. 安排article['a:tikl] n.制品, 产品 ascertain[s'tein] vt. 确定, 查明
模具专业英文术语大全
实用文案 模具英语专业术语 模具述语开模槽：ply bar scot 内模管位：一、入水：gate core/cavity inter-lock 顶针：ejector pin 进入位：gate location 司筒：ejector sleeve 水口形式：gate type 司筒针：edge gate ejector pin 大水口：推板：细水口：stripper plate pin-point gate 缩呵：gate size movable core,return core core 水口大小：puller switching runner/gate 转水口：扣机（尼龙拉勾）：nylon latch lock sprue diameter 唧嘴口径：斜顶：lifter : runner 二、流道模胚（架）：mold base hot runner,hot manifold 热流道：上内模：cavity insert : hot sprue/cold runner 热嘴冷流道下内模：core insert : direct sprue gate 唧嘴直流行位（滑块）：slide round(full/half runner 圆形流道：镶件：insert mold flow analysis 流道电脑分析：压座/斜鸡：wedge :runner balance 流道平衡耐磨板/油板：wedge wear plate hot sprue 热嘴：压条：plate hot manifold 热流道板：撑头: support pillar cartridge heater 发热管：唧嘴：sprue bushing : thermocouples 探针挡板：stop plate connector plug 插头：定位圈：locating ring connector socket 插座：锁扣：latch seal 封料：/密封扣鸡：parting lock set water line 三、运水：推杆：push bar line lpug 喉塞：栓打螺丝：S.H.S.B tube 喉管：顶板：eracuretun plastic tube 塑胶管：活动臂：lever arm jiffy quick connector 快速接头：分流锥：spure sperader plug/socker 水口司mold components 四、模具零件：:bush 垃圾钉：三板模：3-plate mold stop pin 隔片：buffle 二板模：2-plate mold 弹弓柱：导边：/leader pin/guide pin spring rod 边钉弹弓:die spring 导套：边司/bushing/guide bushing 中托司：ejector guide bush 中托司：shoulder guide bushing 中托边：ejector guide pin guide pin ：L中托边镶针：ejector retainner plate 顶针板：pin 销子：托板：support plate dowel pin 波子弹弓：ball catch screw 螺丝：: pipe plug dowel pin 管钉：喉塞文案大全． 实用文案 锁模块：lock plate Mold repair 模具维修 angle from pin 斜顶：Molds 模具
最全的压铸模具相关英语注释.
超值压铸英语 A 安装尺寸install dimension 凹模固定板retainer plate 凹模female die, female mold, negative mold B 备件spare parts 变质modification 变质剂modification agent 扒渣slagging-off 保温炉holding furnace 保压压力dwell pressure 表面缺陷surface defect C 淬火硬度quenching hardness 抽芯core 侧面抽芯side core 抽芯油缸core oil cylinder 插拔式结构plug 抽芯机构core puller 抽芯油缸支架bracket of cylinder
粗糙度roughness/degree 铸件表面粗糙度surface roughness 擦伤galling 尺寸公差dimension tolerance of casting 除气degassing 吹气净化blow purifying 除气剂degassing flux 出渣de-slagging 出渣口slag hole 沉渣sludge 出炉口tap hole 菜花头Cauli-flowering 超声波检验ultrasonic test 重熔re-melting D 端盖cover 动模垫块spacer parallel 锻钢forged steel 氮化处理nitriding treatment 断裂fracture 塑性断裂plastic fracture 导柱guide pillar
模具术语翻译
模具名词中英文对照表序号中文名英文名 1一、水口gate 2进水位gate location 3水口形式gate type 4大水口edge gate 5细水口pin-point gate 6水口大小gate size 7转水口switching gate 8唧嘴口径sprue diameter 9二、流道runner 10热流道hot runner 11冷流道cold runner 12唧嘴直流direct sprue gate 13圆形流道round runner 14模流分析mold flow analysis 15流道平衡runner balance 16热嘴hot sprue 17热流道板hot manifold 18发热管cartridge heater 19探针thermocouples 20插头connector plug 21插座connector socket 22密封/封料seal 23三、运水water line 24喉塞line pug 25喉管tube 26塑胶管plastic tube 27快速接头jiffy quick connector plug 28四、模具零件mold components 29三板模three-plate mold 模具名词中英文对照表 序号中文名英文名 30二板模two-plate mold 31边钉/ 导边leader pin /guide pin
32边司/ 导套bush in g/guide bush ing 33顶针板ejector retainer plate 34托板support plate 35螺丝screw 36管钉dowel pin 37开模槽ply bar score 38内模管位core/cavity inter-lock 39顶针ejector pin 40司筒ejector sleeve 41司筒针ejector pin 42推板stripper plate 43缩呵movable core 44扣机（尼龙拉勾）n yl on latch lock 45斜顶lifter 46模胚（架）mold base 47母模cavity in sert 48公模core insert 49行位（滑块）slide 50 镶件in sert 51压座/斜鸡wedge 52耐磨板/ 油板wedge wear plate 53压条plate 54撑头support pillar 55唧嘴sprue bushing 56挡板stop plate 57定位圈locating ring 58锁扣latch 模具名词中英文对照表 序号中文名英文名 59扣鸡parti ng lock set 60推杆push bar 61栓打螺丝S.H.S.B 62顶板ejector plate 63活动臂lever arm
模具专业英文术语大全
模具专业英文术语大全
模具英语专业术语 模具述语 一、入水：gate 进入位：gate location 水口形式：gate type 大水口：edge gate 细水口：pin-point gate 水口大小：gate size 转水口：switching runner/gate 唧嘴口径：sprue diameter 二、流道: runner 热流道：hot runner,hot manifold 热嘴冷流道: hot sprue/cold runner 唧嘴直流: direct sprue gate 圆形流道：round(full/half runner 流道电脑分析：mold flow analysis 流道平衡:runner balance 热嘴：hot sprue 热流道板：hot manifold 发热管：cartridge heater 探针: thermocouples 插头：connector plug 插座：connector socket 密封/封料：seal 三、运水：water line 喉塞：line lpug 喉管：tube 塑胶管：plastic tube 快速接头：jiffy quick connector plug/socker 四、模具零件：mold components 三板模：3-plate mold 二板模：2-plate mold 边钉/导边：leader pin/guide pin 边司/导套：bushing/guide bushing 中托司：shoulder guide bushing 中托边L：guide pin 顶针板：ejector retainner plate 托板：support plate 螺丝：screw 管钉：dowel pin 开模槽：ply bar scot 内模管位：core/cavity inter-lock 顶针：ejector pin 司筒：ejector sleeve 司筒针：ejector pin 推板：stripper plate 缩呵：movable core,return core core puller 扣机（尼龙拉勾）：nylon latch lock 斜顶：lifter 模胚（架）：mold base 上内模：cavity insert 下内模：core insert 行位（滑块）：slide 镶件：insert 压座/斜鸡：wedge 耐磨板/油板：wedge wear plate 压条：plate 撑头: support pillar 唧嘴：sprue bushing 挡板：stop plate 定位圈：locating ring 锁扣：latch 扣鸡：parting lock set 推杆：push bar 栓打螺丝：S.H.S.B 顶板：eracuretun 活动臂：lever arm 分流锥：spure sperader 水口司:bush 垃圾钉：stop pin 隔片：buffle 弹弓柱：spring rod 弹弓:die spring 中托司：ejector guide bush 中托边：ejector guide pin 镶针：pin 销子：dowel pin 波子弹弓：ball catch 喉塞: pipe plug 锁模块：lock plate 斜顶：angle from pin
模具英语专业术语
模具英语专业术语模具的分类: 冲压模(五金模): stamping die 分离模: cutting die 成形模: forming die 塑胶模: plastics mold 注射模: injection mold 压缩模: compression mold 铸塑模: transfer mold 吹塑模: blow mold 吸塑模: suck mold 铸造模: casting die 砂型铸造: sand casting 压铸模: die casting 锻造模: forging die 塑胶模具术语 一、入水：gate 进入位(入水点)：gate location 水口形式：gate type 大水口(侧浇口): edge gate 潜水口: sub-gate 薄膜式水口: film gate 牛角式潜水口: banana gate 扇形水口: fan gate 环形水口: ring gate 二次水口: 细水口：pin-point gate 水口大小：gate size 转水口：switching runner/gate 唧嘴口径：sprue diameter 直接水口: direct gate 二、流道: runner 热流道：hot runner,hot manifold 热嘴冷流道: hot sprue/cold runner 唧嘴直流: direct sprue gate 圆形(整圆/半圆)流道：round(full/half) runner 矩形流道: rectangle runner 梯形流道: trapezoid runner U形流道: U shape runner 流道电脑分析(模流分析)：mold flow analysis 流道平衡: runner balance
模具专业的英语词汇大全
模具专业的英语词汇大全 一、模具专业英语 入水：gate 进入位：gate location 水口形式：gate type 大水口：edge gate 细水口： pin-point gate 水口大小：gate size 转水口：switching runner/gate 唧嘴口径：sprue diameter 二、流道: runner 热流道：hot runner,hot manifold 热嘴冷流道: hot sprue/cold runner 唧嘴直流: direct sprue gate 圆形流道：round(full/half runner 流道电脑分析：mold flow analysis 流道平衡:runner balance 热嘴：hot sprue 热流道板：hot manifold 发热管：cartridge heater 探针: thermocouples 插头：connector plug 插座： connector socket 密封/封料： seal 三、运水：water line 喉塞：line lpug 喉管：tube 塑胶管：plastic tube 快速接头：jiffy quick connector plug/socker 四、模具零件：mold components 三板模：3-plate mold 二板模：2-plate mold 边钉/导边：leader pin/guide pin 边司/导套：bushing/guide bushing 中托司：shoulder guide bushing 中托边L：guide pin 顶针板：ejector retainner plate 托板：support plate 螺丝： screw 管钉：dowel pin 开模槽：ply bar scot 内模管位：core/cavity inter-lock
模具英语翻译大全
1. The undercut area where interfere with slide block need to be filled material to help the slide can move smoothly.（和滑塊干涉的倒勾請加料填平至滑塊可以順利滑動） 2. The thickening added too thick.(加肉太多) 3. The thickening area is too wide.（加肉面積太大） 4. Gate position is moved.(GATE位置移位) 5. The split line of slide block or the area of slide.(滑塊拆的位置) 6. This area is hard to be filled due to the sharp feature(此處有尖角，填充困難) 7. The strength of this area is too weak and isn’t easy to get c old due to the steel too thin. 8. ( 此處鋼材太薄，強度不足而且不容易冷卻) 9. .The semicircle of cylinder avoids designing on slide block lest it will be pulled apart or cause drag mark. 10. ( 圓柱特徵要有一半圓不可以拆在滑塊上，以免粘滑塊造成拉白，拉斷.) 11. The part will be damaged if we make lifter in this area. 12. ( 此處做斜銷在作動時會削到成品肉厚) 13. This is critical surface where is not allow to add material. 14. ( 這個面是裝配面，不能加料) 15. This thick wall area might because sink mark,Please reduce some wall thickness to improve it.) 16. ( 此處料位太厚，會有縮水，建議減料改善) 17. Please confirm whether it is critical surface or not. Please confirm whether it is acceptable to has Slide split line if we have slide in this area. 18. （此面是不是外觀面，此處做滑塊的話會有結合線，是否可以接受） 19. Please confirm whether we can reduce material to the area where have undercut as indicated to have shut off on core and cavity side. No slide block and lifter to be made. 20. （此處有倒勾，能否減料，使公母模靠破，不做滑塊和斜銷） 21. Please confirm the issues of Parting line, Gate position...Etc otherwise the lead-time will be extended. 22. （請盡快確認這種拆模方式和結構，否則會影響模期） 23. The trim mark of the gate is not visual after open the top case if the gate position is design ed like it 24. （GATE做在此處的話.蓋子打開後看不到GATE的修剪部位） 25. We would suggest to enlarging draft to help tool released.) 26. 加大拔模角，以便脫模順利） 27. There are sharp edges if set the parting line at here, It will reduce the tool life 28. （P.L面開在此處，模具上會有尖角和刀口，對模具壽命有影響） 29. If you insist that the gate position have to be as original design then we would
模具专业英语45315461
模具工程常用词汇 die 模具 figure file, chart file图档 cutting die, blanking die冲裁模 progressive die, follow (-on)die 连续模 compound die复合模 punched hole冲孔 panel board镶块 to cutedges=side cut=side scrap切边 to bending折弯 to pull, to stretch拉伸 Line streching, line pulling线拉伸 engraving, to engrave刻印 upsiding down edges翻边 to stake铆合 designing, to design设计 design modification设计变化 die block模块 folded block折弯块 sliding block滑块 location pin定位销 lifting pin顶料销 die plate, front board模板 padding block垫块 stepping bar垫条 upper die base上模座 lower die base下模座 upper supporting blank上承板 upper padding plate blank上垫板 spare dies模具备品 spring 弹簧 bolt螺栓 document folder文件夹 file folder资料夹 to put file in order整理资料 spare tools location手工备品仓 first count初盘人 first check初盘复棹人 second count 复盘人 second check复盘复核人 equipment设备 waste materials废料 work in progress product在制品 casing = containerazation装箱 quantity of physical invetory second count 复盘点数量quantity of customs count 会计师盘,点数量 the first page第一联 filed by accounting department for reference会计部存查 end-user/using unit(department)使用单位summary of year-end physical inventory bills 年终盘点截止单据汇总表 bill name单据名称 This sheet and physical inventory list will be sent to accounting department together (Those of NHK will be sent to financial department) 本表请与盘点清册一起送会计部－(NHK厂区送财会部) Application status records of year-end physical inventory List and physical inventory card 年终盘点卡与清册使用－ 状况明细表 blank and waste sheet NO. 空白与作废单号 plate电镀 mold成型 material for engineering mold testing工程试模材料 not included in physical inventory不列入盘点sample样品 incoming material to be inspected进货待验description品名 steel/rolled steel钢材 material statistics sheet 物料统计明细表 meeting minutes会议记录 meeting type 会别 distribution department分发单位 location地点 chairman主席 present members出席人员 subject主题 conclusion结论 decision items决议事项 responsible department负责单位 pre-fixed finishing date预定完成日 approved by / checked by / prepared by核准/审核/承办 PCE assembly production schedule sheet PCE组装厂生产排配表 model机锺