Laumas AM-200kg称重传感器
Z6FD1-50kg【Z6FD1-50kg】资料
【广州兰瑟电子】技术部内部培训用
Z6FD1/50kg称重传感器
德国HBM Z6FD1/50kg称重传感器描述：
影响配料秤动态精度的因素
配料秤动态精度的高低直接影响到饲料配比的准备性和饲料产品的质量。
影响配料秤动态精度的主要因素如下：
（一）配料秤的静态精度
配料秤静态精度的高低对动态精度有着决定性的影响。
在任何情况下，配料秤的动态精度都不可能高于其静态精度。
当配料过程中，显示某种物料的配料误差为零时，也是在存在其静态误差前提下的零误差。
只有配料秤的静态精度高，其动态精度才有可能高。
（二）配料秤对称重值的响应速度
对机械秤或机电秤，这个响应速度是指机械杠杆系统当称重值变化时，将此变化值反映出来的时间，这个时间越长，动态精度就越难于保证；对全电子秤，这个响应速度是指数显表采集称重值的频率，这个频率高，动态精度就有可能高。
（三）空中料柱的重量
所谓空中料柱是指从给料器出口到物料重量被秤斗采集到之前的这段空中物料。
空中料柱重量的大小除了与给料器到秤斗之间的距离和物料的比重有关以外，还与配料顺序及给料器给料均匀性有关。
空中料柱重量越大，越不均匀，动态精度越不易控制。
当边进料边配料时也会影响配料精度。
（四）给料器给料速度
给料器给料速度越快，动态精度越不易控制。
【广州兰瑟电子】技术部内部培训用德国HBM Z6FD1/50kg称重传感器同系列：
Z6FD1/10kg
Z6FD1/20kg
Z6FD1/100kg
Z6FD1/200kg
Z6FD1/500kg
Z6FD1/1000kg。
奥美晨曦系列微波传感器说明书
OS100 SERIES Mini-Infrared Transmitter e-mail:**************For latest product manuals: Shop online at User’s G ui d e***********************Servicing North America:U.S.A. Omega Engineering, Inc.Headquarters: Toll-Free: 1-800-826-6342 (USA & Canada only)Customer Service: 1-800-622-2378 (USA & Canada only)Engineering Service: 1-800-872-9436 (USA & Canada only)Tel: (203) 359-1660 Fax: (203) 359-7700e-mail:**************For Other Locations Visit /worldwideThe information contained in this document is believed to be correct, but OMEGA accepts no liability for any errors it contains, and reserves the right to alter specifications without notice.Table of ContentsSection ...................................................................PageSafety Warnings and IEC Symbols (iii)Caution and Safety Information (iii)Section 1 Introduction ....................................................................1-1Section 2Installation ......................................................................1-12.1 Unpacking and Inspection ......................................1-12.2 Electrical Connection ..............................................2-1Section 3Operation ........................................................................3-13.1 Main Board ................................................................3-13.2 Ambient Temperature ..............................................3-23.3 Atmospheric Quality ................................................3-33.4 Measuring Temperature ..........................................3-33.5 Alarm Setting ............................................................3-43.6 Adding Extension Cable...........................................3-4Section 4 Laser Sight Accessory ...................................................4-14.1 Warning and Cautions .............................................4-14.2 Operating the Laser Sight Accessory .....................4-1Section 5 Specifications .................................................................5-15.1 General .......................................................................5-15.2 Laser Sight Accessory (OS100-LS) ..........................5-2Section 6Emissivity Table .............................................................6-1iTable of FiguresFigure Description Page2-1Power Supply & Analog Output Connections ..........2-12-2 Alarm Output Connection ............................................2-13-1 Main PC Board ...............................................................3-23-2 Sensor..............................................................3-2Housing3-3 Optical Field of View .....................................................3-43-4Setting the Temperature Engineering Unit..................3-43-5Mounting Bracket OS100-MB .......................................3-53-6Water Cooling Jacket, OS100-WC ................................3-53-7Typical Water Cool Jacket Assembly ...........................3-53-8Air Purge Collar, OS100-AP..........................................3-63-9DIN Rail Mounting Adapter, OS100-DR ....................3-63-10NEMA-4 Aluminum Enclosure ....................................3-64-1Laser Sighting Accessory, OS100-LS ............................4-24-2Laser Warning Label ......................................................4-2iiSafety Warnings and IEC SymbolsThis device is marked with international safety and hazard symbols in accordance with IEC 1010. It is important to read and follow all precautions and instructions in this manual before operating or commissioning this device as it contains important information relating to safety and EMC. Failure to follow all safety precautions may result in injury and or damage to your calibrator. IEC symbols DescriptionCaution and Safety Information• If the equipment is used in a manner not specified in this manual, the protection provided by the equipment may be impaired.• The installation category is one (1).• There are no user replaceable fuses in this product• The output terminals of this product are for use with equipment (digital meters, chart recorders, etc,) which have no accessible five parts. Such equipment should comply with all the applicable safety requirements.• Do not operate the equipment in flammable or explosive environments.• All connections to the thermometer should be made via a shielded cable, 24 AWG stranded wire with the following ratings: 300V , 105°C (221°F), PVC insulation.• Power must be disconnected before making any electrical connections.• The power supply used to power the thermometer should be VDE or UL approved with the following ratings: 12 to 24vdc @150mA with overload protection of 500mA.iiiCaution, refer to accompanying documentsDirect Current Laser SymbolFrame or ChassisNOTES: ivSection 1 - IntroductionThe low cost OS101 mini-infrared transmitter provides non-contacttemperature measurement for industrial applications. The unit measures atemperature range of -18 to 538°C (0-1000°F) and provides a linear analogoutput of either 4-20 mA, 0-5 VDC, K type TC, 1 mV/°C, or 1 mV/°F.The new OS102 mini-infrared transmitter has all the functions of OS101plus a built-in LED display that shows the measured temperature indegrees F or degrees C which is switchable in the field.The miniature sensor head design 2.5 cm dia. x 6.3 cm Length (1" x 2.5") isideal for measuring temperature in confined, and hard to reach places.The aluminum sensor head as well as the rugged electronic housing (Diecast Aluminum) are NEMA-4 rated.The sensor head is connected to the electronic housing via a 1.82 m (6 feet)shielded cable as standard. The unit provides field adjustable alarmoutput.Section 2 - Installation2.1UnpackingRemove the packing list and verify that you have received all yourequipment. If you have any questions about the shipment, please callCustomer Service at:1-800-622-2378 or 203-359-1660. We can also be reached on the internet:e-mail:**************When you receive the shipment, inspect the container and equipment forany signs of damage. Note any evidence of rough handling in transit.inspection. After examination and removing contents, save packing material and carton in theevent reshipment is necessary.The following items are supplied in the box:• The infrared transmitter including the sensor head and the 1.82 m(6 feet) shielded cable• User's Manual• Mounting Nut1-1The following describes the ordering information:OS102 or OS101 - MA- *,**, where The following optional accessories are available:Here are the Features of OS101 and OS102 infrared transmitters:2.2Electrical Connection Sensor Head Cable - The Sensor head is pre-wired to a 1.8 m (6 feet)shielded cable. Plug & lock-in the male connector to the mating female connector on the aluminum housing.Power & Output Connection - Open the cover of the main aluminum housing. Slide the cable through the strain relief and connect the wires to the terminal block on the board as shown in Fig. 2-1. For Alarm output connection, refer to Fig. 2-2.2-1MA - 4/20 mA output V1 - 0 to 5 VDC output K - Thermocouple output, K type MV - Millivolt output C - 1 mV/°C output F - 1 mV/°F output HT- High temperature sensor head3-1Figure 2-2. Alarm Output Connection Section 3 - Operation3-1Main BoardThe Main Board is shown in Fig. 3-1. Here are the important components on the board:(1) - Terminal Block for Power & Output connections(2) - Single Turn Potentiometer to adjust Emissivity in tenths (0.x_)(3) - Single Turn Potentiometer to adjust Emissivity in hundreds (0._x)(4) -Slide switch to select between real time (Normal Operation) and alarm set point(5) - Alarm set point adjust, P4(6) - Sensor Head connection(7) - Input Zero adjust, P3(8) - Input Span adjust, P2(9) - Output Zero adjust, P5(10) - Output Span adjust, P6Figure 3-1. Main PC Board3.2Ambient TemperatureThe Sensing head can operate in an ambient temperature of 0 to 70°C (32to 158°F). The Sensing head in the high temperature model (-HT) can operate in an ambient temperature of 0 to 85°C (32 to 185°F) without any cooling required. The Sensing head can operate up to 200°C (392°F) using the water cool jacket accessory OS100-WC (See Fig. 3-6).There is a warm up period of 3 minutes after power up. After the warm up period, temperature measurement can be made.When the ambient temperature around the sensor head changes abruptly,the sensor head goes through thermal shock. It takes a certain amount of time for the sensor head to stabilize to the new ambient temperature. For example, it takes about 30 minutes for the sensor head to stabilize going from 25°C to 50°C (77 to 122°F) ambient temperature.The sensor head dimensions are shown in Fig. 3-2.Figure 3-2. Sensor Housing3-23-33.3Atmospheric QualityEnvironments with smoke, dust, and fumes dirty up the optical lens, and cause erroneous temperature readings. To keep the surface of the optical lens clean, the air purge collar accessory is recommended, OS100-AP , See Fig. 3-7.3.4Measuring TemperatureBefore starting to measure temperature, make sure that the following check list is met:ߜ The power and analog output connections are made (Fig. 2-1).ߜThe sensor head is connected to the main unit.ߜThe slide switch (SW1) on the main board is set to real time (Fig. 3-1).ߜThe target is larger than the optical field of view of the sensor head (Fig. 3-3).ߜThe emissivity adjustment on the main board is set properly (Fig. 3-1).ߜThe output load is within the product specification.On OS102 transmitters, follow these additional steps:ߜ The temperature display is set to °F or °C (Fig. 3-4)ߜ For 4-20mA output models, make sure an output load is added, ie. 250ohms.Figure 3-3. Optical Field Of ViewFigure 3-4. Setting the Temperature Engineering Unit3.5Alarm SettingThe unit provides 0-100% alarm set point adjustment. Here is an exampleof an alarm setting.• An OS101-MA(4/20 mA output), the alarm is to be set at 400°Ftemperature.• Connect the alarm output as shown in Fig. 2-2.• Set the slide switch (SW1) on the main board to the Alarm position.• Measure the analog output, and set the Potentiometer P4 until theoutput reads 10.4 mA which is 40% (400°F) of the temperature range.40 x (20-4)[10.4mA=+ 4]100• Set the slide switch (SW1) back to the Real Time position.• If the temperature reading is below the alarm set point, the alarmoutput stays high, otherwise it goes low.On the OS102, you can set the alarm set point directly based on thetemperature display.3.6Adding Extension CableYou can add extension cable between the Sensor Head and the mainelectronic housing up to 15.2 m (50 feet). After adding the extension cable,the Zero input potentiometer, P3 may be re-adjusted. (See Fig. 3-1, forproper analog output reading)The following figures show the mounting bracket (OS100-MB), Watercooling jacket (OS100-WC), Air purge collar (OS100-AP), DIN RailMounting adapter (OS-100-DR), and the main aluminum enclosure. TheDIN Rail Mounting adapter (OS100-DR) is mounted to the bottom of themain aluminum enclosure using two 4-40 screws.A typical water cool jacket assembly is shown in Fig. 3-7, on the following page.1. Mounting Nut2. Mounting Bracket3. Water Cool Jacket4. Sensor Head3-4Figure 3-5. Mounting Bracket OS100-MBFigure 3-6. Water Cooling Jacket, OS100-WCFigure 3-7. Typical Water Cool Jacket Assembly3-5Figure 3-8. Air Purge Collar, OS100-APFigure 3-9. DIN Rail Mounting Adapter, OS-100-DRFigure 3-10. NEMA-4 Aluminum Enclosure3-6Section 4 - Laser Sight Accessory4.1Warning and Cautionsbelow:•Use of controls or adjustments or performance of procedures other than those specified here may result in hazardous radiation exposure.• Do not look at the laser beam coming out of the lens or view directly with optical instruments - eye damage can result.• Use extreme caution when operation the laser sight accessory • Never point the laser accessory at a person • Keep out of the reach of all children4.2Operating the Laser Sight AccessoryThe laser sight accessory screws onto the front of the sensor head. This accessory is only used for alignment of the sensor head to the target area.After the alignment process, the accessory has to be removed from the front of the sensor head before temperature measurement.The laser sight accessory is powered from a small compact battery pack (included with the accessory). Connect the battery pack to the accessory using the cable provided. Aim at the target, and turn on the battery power using the slide switch on the battery pack. Adjust the sensor head position so that the laser beam points to the center of the target area. Turn off the battery pack, and remove the laser sighting accessory from the sensor head. See Fig. 4-1 for reference.4-14-2Figure 4-2. Laser Warning LabelSection 5 - Specifications5.1 - GeneralTemperature Range-18 to 538°C (0 to 1000°F)Accuracy @ 22°C (72°F)±2% of Rdg. or 2.2°C (4°F) whichever is ambient temperature & greateremissivity of 0.95 or greaterOptical Field of View6:1 (Distance/Spot Size)Repeatability±1% of Rdg.Spectral Response 5 to 14 micronsResponse Time150 msec (0 to 63% of final value)Emissivity Range0.1 to 0.99, adjustableOperating Ambient TemperatureMain Transmitter0 to 50°C (32 to 122°F)Sensor Head0 to 70°C (32 to 158°F)Sensor Head (-HT Model)0 to 85°C (32 to 185°F)Sensor Head with OS100-WC(Water Cooling Jacket)0 to 200°C (32 to 392°F)Operating Relative Humidity Less than 95% RH, non-condensingWater Flow Rate for OS100-WC0.25 GPM, room temperatureThermal Shock About 30 minutes for 25°Cabrupt ambient temperature change Warm Up Period 3 minutesAir Flow Rate for OS100-AP 1 CFM (0.5 Liters/sec.)Power12 to 24 VDC @ 100 mAAnalog OutputsMV-F 1 mV/°FMV-C 1 mV/°CK K Type TC - OS101 onlyMA 4 to 20 mAV10 to 5 VDCOutput Load requirementsMin. Load (0 to 5VDC) 1 K-OhmsMax. Load (4 to 20 mA)(Supply Power - 4 )/20 mATransmitter Housing NEMA-4 & IP65, Die Cast AluminumSensor Head Housing NEMA-4 , AluminumAlarm Output Open Drain, 100 mAAlarm Set Point0 to 100% , Adjustable via P4Alarm Deadband14°C (25°F)5-15-25.1 - General Con’t.DimensionsSensor Head25.4 OD. x 63.5 mm L(1" OD. x 2.5" L)Main Housing, OS10165.5 W x 30.5 H x 115.3 mm L(2.58" W x 1.2" H x 4.54" L)Main Housing, OS10265.5 W x 55.9 H x 115.3 mm L(2.58" W x 2.2" H x 4.54" L)Weight 272 g (0.6 lb)5.2Laser Sight Accessory (OS100-LS)Wavelength (Color)630 - 670 nm (Red)Operating Distance (Laser Dot)Up to 9.1 m (30 ft.)Max. Output Optical Power Less than 1 mW at 22°F ambienttemperature.European Classification Class 2, EN60825-1/11.2001Maximum Operating current45 mA at 3 VDCFDA Classification Complies with 21 CFR 1040.10,Class II Laser ProductBeam Diameter 5 mmBeam Divergence< 2 mradOperating Temperature0 to 50°C (32 to 122°F)Operating Relative Humidity Less than 95% RH, non-condensingPower Switch ON / OFF , Slide switch on the BatteryPackPower Indicator Red LEDPower Battery Pack, 3 VDC (Consists of two 1.5VDC AA size Lithium Batteries) Laser Warning Label Located on the head sight circumferenceIdentification Label Located on the head sight circumferenceDimensions38 DIA x 50.8 mm L(1.5" DIA x 2" L)Section 6 - Emissivity Table6-1Material Emissivity (ε)Aluminum – pure highly polished plate . . . . . . . . . . . . . . . . . . . . . . . . 0.04 to 0.06Aluminum – heavily oxidized . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0.20 to 0.31Aluminum – commercial sheet . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0.09Brass – dull plate. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0.22Brass – highly polished, 73.2% Cu, 26.7% Zn. . . . . . . . . . . . . . . . . . . . . . . . . 0.03Chromium – polished. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0.08 to 0.36Copper – polished. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0.05Copper – heated at 600°C (1112°F). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0.57Gold – pure, highly polished or liquid. . . . . . . . . . . . . . . . . . . . . . . . . 0.02 to 0.04Iron and steel (excluding stainless)– polished iron . . . . . . . . . . . . . . . . 0.14 to 0.38Iron and steel (excluding stainless)– polished cast iron. . . . . . . . . . . . . . . . . . . 0.21Iron and steel (excluding stainless)– polished wrought iron . . . . . . . . . . . . . . . 0.28Iron and steel (excluding stainless)– oxidized dull wrought iron . . . . . . . . . . . . 0.94Iron and steel (excluding stainless)– rusted iron plate . . . . . . . . . . . . . . . . . . . 0.69Iron and steel (excluding stainless)– polished steel. . . . . . . . . . . . . . . . . . . . . . 0.07Iron and steel (excluding stainless)– polished steel oxidized at600°C (1112°F). . . . . . . . . . . . . . . . . . . . 0.79Iron and steel (excluding stainless)– rolled sheet steel . . . . . . . . . . . . . . . . . . . 0.66Iron and steel (excluding stainless)– rough steel plate . . . . . . . . . . . . . 0.94 to 0.97Lead – gray and oxidized . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0.28Mercury . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0.09 to 0.12Molybdenum filament . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0.10 to 0.20Nickel – polished . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0.07Nickel – oxidized at 649 to 1254°C (1200°F to 2290°F). . . . . . . . . . . 0.59 to 0.86Platinum – pure polished plate . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0.05 to 0.10Platinum – wire . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0.07 to 0.18Silver – pure and polished . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0.02 to 0.03Stainless steel – polished . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0.07Stainless steel – Type 301 at 232 to 942°C (450°F to 1725°F). . . . . . . 0.54 to 0.63Tin – bright . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0.06Tungsten – filament . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0.39Zinc – polished commercial pure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0.05Zinc – galvanized sheet. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0.23M E T A L S6-2Material Emissivity (ε) Asbestos Board . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .0.96 Asphalt, tar, pitch . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .0.95 to 1.00 Brick– red and rough . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .0.93 Brick– fireclay . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .0.75 Carbon– filament . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .0.53 Carbon– lampblack - rough deposit . . . . . . . . . . . . . . . . . . . . . . . . . .0.78 to 0.84 Glass- Pyrex, lead, soda . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .0.85 to 0.95 Marble– polished light gray . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .0.93 Paints, lacquers, and varnishes– Black matte shellac . . . . . . . . . . . . . . . . . . . .0.91 Paints, lacquers, and varnishes– aluminum paints . . . . . . . . . . . . . . . .0.27 to 0.67 Paints, lacquers, and varnishes– flat black lacquer . . . . . . . . . . . . . . .0.96 to 0.98 Paints, lacquers, and varnishes– white enamel varnish . . . . . . . . . . . . . . . . . .0.91 Porcelain– glazed . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .0.92 Quartz– opaque . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .0.68 to 0.92 Roofing Paper . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .0.91 Tape– Masking . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .0.95 Water . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .0.95 to 0.96 Wood– planed oak . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .0.90 NONMETALSNOTES:6-3NOTES: 6-4OMEGA’s policy is to make running changes, not model changes, whenever an improvement is possible. T his affords our customers the latest in technology and engineering.OMEGA is a trademark of OMEGA ENGINEERING, INC.© Copyright 2017 OMEGA ENGINEERING, INC. All rights reserved. T his document may not be copied, photocopied, reproduced, translated, or reduced to any electronic medium or machine-readable form, in whole or in part, without the prior written consent of OMEGA ENGINEERING, INC.FOR WARRANTY RETURNS, please have the following information available BEFORE contacting OMEGA:1. P urchase Order number under which the product was PURCHASED,2. M odel and serial number of the product under warranty, and3. Repair instructions and/or specific problems relative to the product.FOR NON-WARRANTY REPAIRS, consult OMEGA for current repair charges. Have the following information available BEFORE contacting OMEGA:1. Purchase Order number to cover the COST of the repair,2. Model and serial number of the product, and 3. Repair instructions and/or specific problems relative to the product.RETURN REQUESTS/INQUIRIESDirect all warranty and repair requests/inquiries to the OMEGA Customer Service Department. BEFORE RET URNING ANY PRODUCT (S) T O OMEGA, PURCHASER MUST OBT AIN AN AUT HORIZED RET URN (AR) NUMBER FROM OMEGA’S CUST OMER SERVICE DEPART MENT (IN ORDER T O AVOID PROCESSING DELAYS). The assigned AR number should then be marked on the outside of the return package and on any correspondence.T he purchaser is responsible for shipping charges, freight, insurance and proper packaging to preventbreakage in transit.WARRANTY/DISCLAIMEROMEGA ENGINEERING, INC. warrants this unit to be free of defects in materials and workmanship for a period of 25 months from date of purchase. OMEGA’s WARRANTY adds an additional one (1) month grace period to the normal two (2) year product warranty to cover handling and shipping time. This ensures that OMEGA’s customers receive maximum coverage on each product.If the unit malfunctions, it must be returned to the factory for evaluation. OMEGA’s Customer Service Department will issue an Authorized Return (AR) number immediately upon phone or written request. Upon examination by OMEGA, if the unit is found to be defective, it will be repaired or replaced at no charge. OMEGA’s WARRANT Y does not apply to defects resulting from any action of the purchaser, including but not limited to mishandling, improper interfacing, operation outside of design limits, improper repair, or unauthorized modification. T his WARRANT Y is VOID if the unit shows evidence of having been tampered with or shows evidence of having been damaged as a result of excessive corrosion; or current, heat, moisture or vibration; improper specification; misapplication; misuse or other operating conditions outside of OMEGA’s control. Components in which wear is not warranted, include but are not limited to contact points, fuses, and triacs.OMEGA is pleased to offer suggestions on the use of its various products. However, OMEGA neither assumes responsibility for any omissions or errors nor assumes liability for any damages that result from the use of its products in accordance with information provided by OMEGA, either verbal or written. OMEGA warrants only that the parts manufactured by the company will be as specified and free of defects. OMEGA MAKES NO OTHER WARRANTIES OR REPRESENTATIONS OF ANY KIND WHATSOEVER, EXPRESSED OR IMPLIED, EXCEPT THAT OF TITLE, AND ALL IMPLIED W ARRANTIES INCLUDING ANY W ARRANTY OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE HEREBY DISCLAIMED. LIMITATION OF LIABILITY: The remedies of purchaser set forth herein are exclusive, and the total liability of OMEGA with respect to this order, whether based on contract, warranty, negligence, indemnification, strict liability or otherwise, shall not exceed the purchase price of the component upon which liability is based. In no event shall OMEGA be liable for consequential, incidental or special damages.CONDITIONS: Equipment sold by OMEGA is not intended to be used, nor shall it be used: (1) as a “Basic Component” under 10 CFR 21 (NRC), used in or with any nuclear installation or activity; or (2) in medical applications or used on humans. Should any Product(s) be used in or with any nuclear installation or activity, medical application, used on humans, or misused in any way, OMEGA assumes no responsibility as set forth in our basic WARRANT Y /DISCLAIMER language, and, additionally, purchaser will indemnify OMEGA and hold OMEGA harmless from any liability or damage whatsoever arising out of the use of theProduct(s) in such a manner.Where Do I Find Everything I Need forProcess Measurement and Control?OMEGA…Of Course!Shop online at TEMPERATUREM U Thermocouple, RTD & Thermistor Probes, Connectors,Panels & AssembliesM U Wire: Thermocouple, RTD & ThermistorM U Calibrators & Ice Point ReferencesM U Recorders, Controllers & Process MonitorsM U Infrared PyrometersPRESSURE, STRAIN AND FORCEM U Transducers & Strain GagesM U Load Cells & Pressure GagesM U Displacement TransducersM U Instrumentation & AccessoriesFLOW/LEVELM U Rotameters, Gas Mass Flowmeters & Flow ComputersM U Air Velocity IndicatorsM U Turbine/Paddlewheel SystemsM U Totalizers & Batch ControllerspH/CONDUCTIVITYM U pH Electrodes, Testers & AccessoriesM U Benchtop/Laboratory MetersM U Controllers, Calibrators, Simulators & PumpsM U Industrial pH & Conductivity EquipmentDATA ACQUISITIONM U Communications-Based Acquisition SystemsM U Data Logging SystemsM U Wireless Sensors, Transmitters, & ReceiversM U Signal ConditionersM U Data Acquisition SoftwareHEATERSM U Heating CableM U Cartridge & Strip HeatersM U Immersion & Band HeatersM U Flexible HeatersM U Laboratory HeatersENVIRONMENTALMONITORING AND CONTROLM U Metering & Control InstrumentationM U RefractometersM U Pumps & TubingM U Air, Soil & Water MonitorsM U Industrial Water & Wastewater TreatmentM U pH, Conductivity & Dissolved Oxygen InstrumentsM3572/1217。
广测YZC称重传感器参考资料
广测YZC称重传感器参考资料广测传感器参照图YZC-522系列拉式S型称重传感器产品型号产品描述YZC-522-50kg 钢制拉式S型称重传感器，容量50KGYZC-522-100kg 钢制拉式S型称重传感器，容量100KGYZC-522-150kg 钢制拉式S型称重传感器，容量150KGYZC-522-200kg 钢制拉式S型称重传感器，容量250KGYZC-522-500kg 钢制拉式S型称重传感器，容量500KGYZC-522-1.5t 钢制拉式S型称重传感器，容量1500KGS型应用于拉伸/拉力测量，试验机，吊钩秤，搅拌站等。
YZC-522TS系列拉式S型称重传感器产品型号产品描述YZC-522TS-50kg 钢制拉式S型称重传感器，容量50KGYZC-522TS-100kg 钢制拉式S型称重传感器，容量100KGYZC-522TS-150kg 钢制拉式S型称重传感器，容量150KGYZC-522TS-200kg 钢制拉式S型称重传感器，容量250KGYZC-522TS-500kg 钢制拉式S型称重传感器，容量500KGYZC-522TS-1.5t 钢制拉式S型称重传感器，容量1500KGS型应用于拉伸/拉力测量，试验机，吊钩秤，搅拌站等YZC-5B（516）系列拉式S型称重传感器产品型号产品描述YZC-5B（516）-20kg 钢制拉式S型称重传感器，容量20KG YZC-5B（516）-30kg 钢制拉式S型称重传感器，容量30KG YZC-5B（516）-50kg 钢制拉式S型称重传感器，容量50KG YZC-5B（516）-100kg 钢制拉式S型称重传感器，容量100KG YZC-5B（516）-150kg 钢制拉式S型称重传感器，容量150KG YZC-5B（516）-200kg 钢制拉式S型称重传感器，容量250KG YZC-5B（516）-500kg 钢制拉式S型称重传感器，容量500KG YZC-5B（516）-750kg 钢制拉式S型称重传感器，容量500KG YZC-5B（516）-1.0t 钢制拉式S型称重传感器，容量1000KG YZC-5B（516）-1.5t 钢制拉式S型称重传感器，容量1500KG YZC-5B（516）-2.0t 钢制拉式S型称重传感器，容量2000KG YZC-5B（516）-3.0t 钢制拉式S型称重传感器，容量3000KGYZC-5B（516）-5.0t 钢制拉式S型称重传感器，容量5000KG YZC-5B（516）-7.5t 钢制拉式S型称重传感器，容量7500KG YZC-5B（516）-10t 钢制拉式S型称重传感器，容量10000KG YZC-5B（516）-20t 钢制拉式S型称重传感器，容量20000KG YZC-5B（516）-30t 钢制拉式S型称重传感器，容量30000KG S型应用于拉伸/拉力测量，试验机，吊钩秤，搅拌站等YZC-328系列压式波纹管称重传感器产品型号产品描述YZC-328-5kg 钢质压式波纹管称重传感器，容量5KGYZC-328-10kg 钢质压式波纹管称重传感器，容量10KGYZC-328-20kg 钢质压式波纹管称重传感器，容量20KGYZC-328-30kg 钢质压式波纹管称重传感器，容量30KGYZC-328-50kg 钢质压式波纹管称重传感器，容量50KGYZC-328-100kg 钢质压式波纹管称重传感器，容量100KG YZC-328-200kg 钢质压式波纹管称重传感器，容量200KG YZC-328-300kg 钢质压式波纹管称重传感器，容量300KG YZC-328-500kg 钢质压式波纹管称重传感器，容量500KG波纹管式应用于平台秤，料斗秤，皮带秤，包装称等。
Zemic
美国Zemic称重传感器广州南创电子科技有限公司传感器事业部内部使用资料美国ZEMIC有限公司在美国成立,在多个国家设立了分支机构或办事处,生产基地遍布美洲、东欧等地,在中国设立了广州南创传感器事业部,可为用户的实验和生产提供最佳的服务与解决方案。
美国Zemic称重传感器美国Zemic称重传感器单点式称重传感器：美国ZEMIc称重传感器，如下：Zemic称重传感器HM14C-C3-30T-13B6特性◆可满足0.05kg-300kg量程范围内的测量。
◆铝合金材料，平行梁结构◆硅橡胶密封，表面阳极化，耐腐蚀性佳。
◆整体结构，安装使用方便。
◆适用于电子计价秤、电子平台秤等各类电子称重设备。
◆量程：0.05㎏到300㎏◆高精度◆最大秤台尺寸450*450㎜Zemic称重传感器（load cell）单点式称重传感器L6B、L6D、L6E、L6E3、L6F、L6G、L6J、L6H5：L6E3-C3-50kg-3G,L6E3-C3-100kg-3G,L6E3-C3-150KG-3G,L6E3-C3-200KG-3G,L6E3-C3-25 0KG-3G,L6E3-C3-300KG-3G,L6E-C3-50KG-2B,L6E-C3-60KG-2B,L6E-C3-80KG-2B,L6E-C3-100KG-2B,L6E-C3-150KG-2B, L6E-C3-200KG-2B,L6E-C3-300KG-2B,L6D-C3-2.5KG-0.4B,L6D-C3-3KG-0.4B,L6D-C3-5KG-0.4B,L6D-C3-6KG-0.4B ,L6D-C3-8KG-0.4B,L6D-C3-10KG-0.4B,L6D-C3-15KG-0.4B,L6D-C3-20KG-0.4B,L6D-C3-30KG-0.4B,L6D-C 3-35KG-0.4B,L6D-C3-40KG-0.4B,L6D-C3-50KG-0.4BL6H5-C3D-4KG-1.75B，L6H5-C3D-5KG-1.75B，L6H5-C3D-6KG-1.75B，L6H5-C3D-8KG-1.75B，L6H5-C3D-10KG-1.75B，L6H5-C3D-20KG-1.75B，L6G-C3-50KG-3G6，L6G-C3-100KG-3G6，L6G-C3-150KG-3G6，L6G-C3-200KG-3G6，L6G-C3-250KG-3G6，L6G-C3-300KG-3G6，L6G-C3-500KG-3G6，L6G-C3-600KG-3G6，L6G-C3-50KG-3G6，L6G-C3-100KG-3G6，L6G-C3-150KG-3G6，L6G-C3-200KG-3G6，L6G-C3-250KG-3G6，L6G-C3-300KG-3G6，L6G-C3-500KG-3G6，L6G-C3-600KG-3G6，L6F-C3-50KG-3B6,L6F-C3-100KG-3B6,L6F-C3-150KG-3B6,L6F-C3-200KG-3B6,L6F-C3-250 KG-3B6,L6F-C3-500KG-3B6,L6F-C3-750KG-3B6,L6F-C3-1.0T-3B6,L6F-C3-2.0T-3B6,L6F-C 3D-50kg-3G,L6F-C3D-100kg-3G, /zemicL6F-C3D-150kg-3G,L6F-C3D-200kg-3G,L6F-C3D-250kg-3G,L6F-C3D-500kg-3G,L6F-C3D-7 50kg-3G,L6F-C3D-1000kg-3G,L6F-C3D-2000kg-3G,L6B-C3D-0.3KG-0.45B,L6B-C3D-0.6KG-0.45B,L6B-C3D-1.2KG-0.45B ,L6B-C3D-3KG-0.45B B6E-C3-100KG-2B,B6E-C3-150KG-2B,B6E-C3-200KG-2B,B6E-C3-300KG-2B,B6Q-C3-200KG-1.5B6,B6Q-C3-250KG-1.5B6,B6N-C3-15kg-1B6,B6N-C3-20kg-1B6,B6N-C3-30kg-1B6,B6N-C3-50kg-1B6,B6N-C3-75kg-1B6,B6N-C3-100kg-1B6,B6N-C3-150kg-1B6,B6N-C3-200kg-1B6,H6G-C3-100KG-3B6,H6G-C3-150KG-3B6,H6G-C3-200KG-3B6,H6G-C3-250KG-3B6,H6G-C 3-300KG-3B6,H6G-C3-500KG-3B6,H6G-C3-600KG-3B6,B6F-C3-100KG-3B6,B6F-C3-150KG-3B6,B6F-C3-200KG-3B6,B6F-C3-250KG-3B6,B6F-C3-5 00KG-3B6,B6F-C3-750KG-3B6,B6F-C3-1.0T-3B6,B6F-C3-2.0T-3B6,L6W-C3-50KG-3G6,L6W-C3-75KG-3G6,L6W-C3-100KG-3G6,L6W-C3-150KG-3G6,L6W-C3-200KG-3G6,L6W-C3-250KG-3G6,L6W-C3-500KG-3G6,L6W-C3-635KG-3G6,Zemic 称重传感器双剪切梁式特,性：◆Zemic 可满足10t～50t量程范围内的精确测量。
进口称重传感器
进口称重传感器广州南创谭工德国HBM称重传感器、压力、扭矩传感器及仪表、TEDEA-HUNTLEIGH称重传感器、瑞士METTLER TOLEDO称重传感器、西班牙Utilcell称重传感器、美国Celtron 称重传感器系列、美国Amcells称重传感器、美国RICE LAKE称重传感器、美国Nobel张力传感器、美国Sensortroncs(STS)称重传感器、美国KELI称重传感器、美国Transcell称重传感器及仪表系列、美国BLH过程测量控制系统、荷兰PHILIPS称重传感器、美国Interface称重传感器、ZEMIC称重传感器、日本NMB 称重传感器、日本A&D传感器、日本ASAHI隔离端子及数字面板表、压力传感器及仪表系列、美国MSI压力传感器、美国MEAS压力传感器及位移传感器、美国Motorola 压力传感器、韩国DACELL称重传感器、韩国CAS传感器、韩国Bongshin 称重传感器、韩国SETech传感器、美国Freescale汽车用传感器、美国AmCells A称重传感器、德国Sartorius称重传感器、德国FLINTEC传感器及仪表、德国NOVOtechnik位移传感器、意大利Laumas称重传感器及其仪表、英国Omega传感器、法国Master-K称重传感器及其显示器等世界著名公司的品牌产品。
产品广泛用于航空航天、化纤、机械、能源、交通建筑、钢铁、环保、制药、矿山、建筑机械、给水排水、石油天然气、化工冶金、水利电力、热力造纸、市政管理等领域中的电子秤、汽车衡、配料秤、全电子汽车衡、电子地上衡电子台秤、电子吊称、定量包装系统。
进口称重传感器光电池是利用光生伏特效应把光能直接转变成电能的器件，Mettler Toledo称重传感器在有光照情况下就是一个电源。
传感器由于它广泛应用于把太阳能直接变为电能，因此又称为太阳能电池。
进口称重传感器光电池的种类很多，NMB称重传感器以其半导体材料加以区别，如硒光电池、锗光电池、硅光电池、氧化亚铜光电池、砷化稼光电池、磷化稼光电池等。
laumas FCAX-500KG称重传感器
LAUMAS FCAX-500KG称重传感器
LAUMAS FCAX-500KG称重传感器介绍：
LAUMAS称重传感器分为：单点式、剪切(悬臂)梁式、弯曲梁式、拉力式、柱压式、轴销式、锚式、钢丝绳测力限重器式、增辐放大器式等。
意大利LAUMAS FCAX-500KG称重传感器系列型号：FCAX-30KG称重传感器
FCAX-50KG称重传感器
FCAX-70KG称重传感器
FCAX-150KG称重传感器
FCAX-300KG称重传感器
FCAX-500KG称重传感器
FCAX-750KG称重传感器
FCAX-1000KG称重传感器
FCAX-1500KG称重传感器
LAUMAS FCAX-500KG称重传感器参数：
LAUMAS FCAX-500KG称重传感器同品牌分类：CBLS压式称重传感器(load cells)
PTC单点式称重传感器(load cells)
PTAI单点式称重传感器(load cells)
PT单点式称重传感器(load cells)
PRC单点式称重传感器(load cells)
PR单点式称重传感器(load cells)
PL单点式称重传感器(load cells)
PEI单点式称重传感器(load cells)
PEC单点式称重传感器(load cells)
PE单点式称重传感器(load cells)
AZL单点式称重传感器(load cells)
AZ单点式称重传感器(load cells)
AU单点式称重传感器(load cells)
ATL单点式称重传感器(load cells)。
英国Omega称重传感器
英国Omega称重传感器广州南创蔡工英国Omega称重传感器公司简介英国Omega称重传感器自1962年成立以来，已经成长从生产热电偶单一产品线建立在技术市场的全球领导者，提供超过10万个最先进的产品用于测量和控制温度，湿度，压力，应变，力，流量，液位，pH值和电导率。
英国Omega称重传感器还为客户提供一个完整的数据采集，电加热和定制设计的产品线。
在过去的三十年，英国Omega称重传感器的手册，曾担任世界各地的工程师提供有价值的参考工具。
质量检测仪器和出色的客户服务，一直是英国Omega称重传感器成功的基石。
英国Omega称重传感器(load cells)的首要任务是明确的。
英国Omega称重传感器的设施存在“协助”解决方案，您的需求。
英国Omega称重传感器持续增长英国Omega称重传感器公司总部设在康涅狄格州斯坦福德，在位于新泽西州的布里奇波特。
Omega®除了其在英国的子公司，也有在加拿大的网站，Omega工程有限公司，英国Omega称重传感器集团还包括纽波特电子（网站在纽波特，美国，德国，法国，荷兰和捷克共和国），OMEGADYNE（位于美国俄亥俄州哥伦布市附近）以及Omega万泽蒂（在波士顿，马萨诸塞州）。
英国Omega称重传感器的产品在多个国家设立了国外办事处及售后服务中心，并在中国设立了广州南创传感事业部，为英国Omega称重传感器提供最佳的服务与解决方案。
在过去的40年Omega®已经从出身卑微，成为在过程测量和控制领域的国际领先地位，提供超过10万件。
英国Omega称重传感器公司的基本理念是创造就业机会，使个人实现自己最大的潜能。
英国Omega称重传感器公司的5个创始原则是：•英国Omega称重传感器创意及管理方法之间保持平衡在一个快速增长的创业•英国Omega称重传感器市场的商品和服务在每一个具体的广谱纪律，同时力争成为在该领域的领导者•英国Omega称重传感器发展及维持一个独特的推销和宣传风格•英国Omega称重传感器鼓励经理们发展自己的风格•英国Omega称重传感器记住的营销理念，顾客就是上帝英国Omega称重传感器(load cells)的成功在于它的质量，卓越的客户服务和具有丰富经验的技术支持的承诺。
梅特勒(常州)托利多称重传感器参考资料
梅特勒（常州）托利多称重传感器参考资料梅特勒托利多称重传感器参照图瑞士METTLER TOLEDO梅特勒托利多称重传感器类型TSC/TSB拉式S型称重传感器产品型号产品描述TSC-50 钢质拉式传感器，容量50KG,5M电缆TSC-100 钢质拉式传感器，容量100KG,5M电缆TSC-200 钢质拉式传感器，容量200KG,5M电缆TSC-300 钢质拉式传感器，容量300KG,5M电缆TSC-500 钢质拉式传感器，容量500KG,5M电缆TSC-1000 钢质拉式传感器，容量1000KG,5M电缆TSB-2000 钢质拉式传感器，容量2000KG,5M电缆TSB-2000 钢质拉式传感器，容量2000KG,12M电缆TSB-3000 钢质拉式传感器，容量3000KG,5M电缆TSB-3000 钢质拉式传感器，容量3000KG,12M电缆TSB-5000 钢质拉式传感器，容量5000KG,5M电缆TSB-5000 钢质拉式传感器，容量5000KG,12M电缆拉式称重传感器连接件产品型号产品描述TP-100～300 配100～300KG TSC,拉杆式TP-500～1000 配500～1000KG TSC,拉杆式ZP-100～300 配100～300KG TSC,关节轴承式ZP-500～1000 配500～1000KG TSC,关节轴承式ZP-2000 配2000KG TSB,关节轴承式ZP-3000 配3000KG TSB,关节轴承式ZP-5000 配5000KG TSB,关节轴承式SB系列剪切梁传感器产品型号产品描述SB-0.3 剪切梁传感器，容量0.3T,盲孔，4M电缆SB-0.5t 剪切梁传感器，容量0.5T,盲孔，4M电缆SB-0.5t 剪切梁传感器，容量0.5T,盲孔，12M电缆SB-1t 剪切梁传感器，容量1T,盲孔，4M电缆SB-1t 剪切梁传感器，容量1T,盲孔，12M电缆SB-2t 剪切梁传感器，容量2T,盲孔，4M电缆SB-2t 剪切梁传感器，容量2T,盲孔，12M电缆SB-3t 剪切梁传感器，容量3T,盲孔，4M电缆SB-5t 剪切梁传感器，容量5T,盲孔孔，5M电缆SB-10t 剪切梁传感器，容量10T,盲孔孔，6M电缆SB-15t 剪切梁传感器，容量15T,盲孔孔，10M电缆SB-20t 剪切梁传感器，容量20T,盲孔孔，10M电缆SBT系列剪切梁传感器产品型号产品描述SBT-0.3t 剪切梁传感器，容量0.3T,通孔，4M电缆SBT-0.5t 剪切梁传感器，容量0.5T,通孔，4M电缆SBT-1t 剪切梁传感器，容量1T,通孔，4M电缆SBT-2t 剪切梁传感器，容量2T,通孔，4M电缆SBT-3t 剪切梁传感器，容量3T,通孔，4M电缆SBT-5t 剪切梁传感器，容量5T,通孔，5M电缆SBS系列剪切梁传感器产品型号产品描述SBS-0.3t 剪切梁传感器，容量0.3T,螺纹孔，4M电缆SBS-0.5t 剪切梁传感器，容量0.5T,螺纹孔，4M电缆SBS-1t 剪切梁传感器，容量1T,螺纹孔，4M电缆SBS-2t 剪切梁传感器，容量2T,螺纹孔，4M电缆SBS-3t 剪切梁传感器，容量3T,螺纹孔，4M电缆SBC系列紧密型剪切梁称重传感器及其连接件产品型号产品描述SBC-0.5t 紧密型剪切梁传感器，容量0.5T,3M电缆SBC-0.5t 紧密型剪切梁传感器，容量0.5T,6M电缆SBC-1t 紧密型剪切梁传感器，容量1T,3M电缆SBC-1t 紧密型剪切梁传感器，容量1T,6M电缆SBC-2t 紧密型剪切梁传感器，容量2T,3M电缆SBC-2t 紧密型剪切梁传感器，容量2T,6M电缆SBC-3t 紧密型剪切梁传感器，容量3T,3M电缆SBC-3t 紧密型剪切梁传感器，容量3T,6M电缆连接件SPC-0.5～3T 紧密型剪切梁称重传感器专用连接件SPC-5T 紧密型剪切梁称重传感器专用连接件SBH系列不锈钢焊接密封传感器产品型号产品描述SBH-0.25t 弯曲梁称重传感器，称重容量0.25T，5M电缆SBH-0.5t 弯曲梁称重传感器，称重容量0.5T，5M电缆SBH-1t 弯曲梁称重传感器，称重容量1T，5M电缆SBH-2t 弯曲梁称重传感器，称重容量2T，5M电缆SBH-3t 弯曲梁称重传感器，称重容量3T，5M电缆SBH-5 弯曲梁称重传感器，称重容量5T，5M电缆IL系列称重传感器产品型号产品描述IL-150KG 钢质弯曲梁传感器，容量150KG,2.5M电缆IL-250KG 钢质弯曲梁传感器，容量250KG,2.5M电缆IL-500KG 钢质弯曲梁传感器，容量500KG,2.5M电缆IL-1000KG 钢质弯曲梁传感器，容量1000KG,2.5M电缆IL-2000KG 钢质弯曲梁传感器，容量2000KG,2.5M电缆0745A/0743系列不锈钢焊接密封传感器产品型号产品描述0745A-0.22t 0745A称重传感器0.22T,2.2M电缆0745A-0.22t 0745A称重传感器0.22T,4.5M电缆0745A-0.22t 0745A称重传感器0.22T,9M电缆0745A-0.55t 0745A称重传感器0.55T,2.2M电缆0745A-0.55t 0745A称重传感器0.55T,4.5M电缆0745A-0.55t 0745A称重传感器0.55T,9M电缆0745A-1.1t 0745A称重传感器1.1T,2.2M电缆0745A-1.1t 0745A称重传感器1.1T,4.5M电缆0745A-1.1t 0745A称重传感器1.1T,9M电缆0745A-2.2t 0745A称重传感器2.2T,2.2M电缆0745A-2.2t 0745A称重传感器2.2T,4.5M电缆0745A-2.2t 0745A称重传感器2.2T,9M电缆0745A-4.4t 0745A称重传感器4.4T,4.5M电缆0745A-4.4t 0745A称重传感器4.4T,9M电缆0745A-4.4t 0745A称重传感器4.4T,18M电缆GD柱式称重传感器产品型号产品描述GD-15 柱式GD不锈钢称重传感器,容量15t，13M电缆GD-20 柱式GD不锈钢称重传感器,容量20t，13M电缆GD-30 柱式GD不锈钢称重传感器,容量30t，13M电缆GD-50 柱式GD不锈钢称重传感器,容量50t，13M电缆GD-100 柱式GD不锈钢称重传感器,容量100t，13M电缆GD柱式防爆传感器产品型号产品描述GD-15x 柱式GD不锈钢称重传感器,容量15t，13M电缆GD-20x 柱式GD不锈钢称重传感器,容量20t，13M电缆GD-30x 柱式GD不锈钢称重传感器,容量30t，13M电缆GD-50x 柱式GD不锈钢称重传感器,容量50t，13M电缆GD-100x 柱式GD不锈钢称重传感器,容量100t，13M电缆电流型模拟量输出传感器产品型号产品描述GD-15-AOC GD电流型模拟量输出传感器，容量15T,13M电缆GD-20-AOC GD电流型模拟量输出传感器，容量20T,13M电缆GD-30-AOC GD电流型模拟量输出传感器，容量30T,13M电缆GD-50-AOC GD电流型模拟量输出传感器，容量50T,13M电缆GD-100-AOC GD电流型模拟量输出传感器，容量100T,13M电缆GD-200-AOC GD电流型模拟量输出传感器，容量200T,20M电缆GD-250-AOC GD电流型模拟量输出传感器，容量250T,20M电缆GD-300-AOC GD电流型模拟量输出传感器，容量300T,30M电缆GD-400-AOC GD电流型模拟量输出传感器，容量400T,30M电缆GD-500-AOC GD电流型模拟量输出传感器，容量500T,30M电缆PGD-2-AOC GD电流型模拟量输出传感器，容量2T,13M电缆PGD-5-AOC GD电流型模拟量输出传感器，容量5T,13M电缆PGD-10-AOC GD电流型模拟量输出传感器，容量10T,13M电缆PGD-20-AOC GD电流型模拟量输出传感器，容量20T,13M电缆PGD-30-AOC GD电流型模拟量输出传感器，容量30T,13M电缆PGD-50-AOC GD电流型模拟量输出传感器，容量50T,13M电缆选配件（用于隔离电源及信号）3042隔离安全栅3042隔离安全栅屏蔽电缆瑞士METTLER TOLEDO梅特勒托利多称重模块类型FW/CW系列称重模块产品型号产品描述FW-0.3t 固定式静载模块,容量0.3t,4M电缆FW-0.3t 半浮动式静载模块,容量0.3t,4M电缆FW-0.3t 全浮动式静载模块,容量0.3t,4M电缆FW-0.5t 固定式载模块,容量0.5t,4M电缆FW-0.5t 半浮动式静载模块,容量0.5t,4M电缆FW-0.5t 全浮动式静载模块,容量0.5t,4M电缆FW-1t 固定式静载模块,容量1t,4M电缆FW-1t 固定式静载模块,容量1t,12M电缆FW-1t 半浮动式静载模块,容量1t,4M电缆FW-1t 半浮动式静载模块,容量1t,12M电缆FW-1t 全浮动式静载模块,容量1t,4M电缆FW-1t 全浮动式静载模块,容量1t,12M电缆FW-2t 固定式静载模块,容量2t,4M电缆FW-2t 固定式静载模块,容量2t,12M电缆FW-2t 半浮动式静载模块,容量2t,4M电缆FW-2t 半浮动式静载模块,容量2t,12M电缆FW-2t 全浮动式静载模块,容量2t,4M电缆FW-2t 全浮动式静载模块,容量2t,12M电缆FW-3t 固定式静载模块,容量3t,4M电缆FW-3t 半浮动式静载模块,容量3t,4M电缆FW-3t 全浮动式静载模块,容量3t,4M电缆FW-5t 固定式静载模块,容量5t,5M电缆FW-5t 半浮动式静载模块,容量5t,5M电缆FW-5t 全浮动式静载模块,容量5t,5M电缆FW-10t 固定式静载模块,容量10t,6M电缆FW-10t 半浮动式静载模块,容量10t,6M电缆FW-10t 全浮动式静载模块,容量10t,6M电缆FW-15t 固定式静载模块,容量15t,10M电缆FW-15t 半浮动式静载模块,容量15t,10M电缆FW-15t 全浮动式静载模块,容量15t,10M电缆FW-20t 固定式静载模块,容量20t,10M电缆FW-20t 半浮动式静载模块,容量20t,10M电缆FW-20t 全浮动式静载模块,容量20t,10M电缆CW-0.3t 动载模块,容量0.3t,4M电缆CW-0.5t 动载模块,容量0.5t,4M电缆CW-1t 动载模块,容量1t,4M电缆CW-2t 动载模块,容量2t,4M电缆CW-3t 动载模块,容量3t,4M电缆CW-5t 动载模块,容量5t,5M电缆CW-10t 动载模块,容量10t,6M电缆CW-15t 动载模块,容量15t,10M电缆CW-20t 动载模块,容量20t,10M电缆FWC/CWC系列称重模块产品型号产品描述FWC-0.22x 防爆固定式不锈钢静载模块,容量0.22t,4.5M电缆FWC-0.22x 防爆浮动式不锈钢静载模块,容量0.22t,4.5M电缆FWC-0.22x 防爆半防爆浮动式不锈钢静载模块,容量0.22t,4.5M电缆FWC-0.55x 防爆固定式不锈钢静载模块,容量0.55t,4.5M电缆FWC-0.55x 防爆浮动式不锈钢静载模块,容量0.55t,4.5M电缆FWC-0.55x 防爆半防爆浮动式不锈钢静载模块,容量0.55t,4.5M电缆FWC-1.1x 防爆固定式不锈钢静载模块,容量1.1t,4.5M电缆FWC-1.1x 防爆浮动式不锈钢静载模块,容量1.1t,4.5M电缆FWC-1.1x 防爆半防爆浮动式不锈钢静载模块,容量1.1t,4.5M电缆FWC-2.2x 防爆固定式不锈钢静载模块,容量2.2t,4.5M电缆FWC-2.2x 防爆浮动式不锈钢静载模块,容量2.2t,4.5M电缆FWC-2.2x 防爆半防爆浮动式不锈钢静载模块,容量2.2t,4.5M电缆FWC-4.4x 防爆固定式不锈钢静载模块,容量4.4t,4.5M电缆FWC-4.4x 防爆浮动式不锈钢静载模块,容量4.4t,4.5M电缆FWC-4.4x 防爆半防爆浮动式不锈钢静载模块,容量4.4t,4.5M电缆FWC-9x 防爆固定式不锈钢静载模块,容量9t,9M电缆FWC-9x 防爆浮动式不锈钢静载模块,容量9t,9M电缆FWC-9x 防爆半防爆浮动式不锈钢静载模块,容量9t,9M电缆FWC-13.6x 防爆固定式不锈钢静载模块,容量13.6t,9M电缆FWC-13.6x 防爆浮动式不锈钢静载模块,容量13.6t,9M电缆FWC-13.6x 防爆半防爆浮动式不锈钢静载模块,容量13.6t,9M电缆FWC-20x 防爆固定式不锈钢静载模块,容量20t,9M电缆FWC-20x 防爆浮动式不锈钢静载模块,容量20t,9M电缆FWC-20x 防爆半防爆浮动式不锈钢静载模块,容量20t,9M电缆CWC-0.22x 不锈钢动载模块,容量0.22t,4.5M电缆CWC-0.55x 不锈钢动载模块,容量0.55t,4.5M电缆CWC-1.1x 不锈钢动载模块,容量1.1t,4.5M电缆CWC-2.2x 不锈钢动载模块,容量2.2t,4.5M电缆CWC-4.4x 不锈钢动载模块,容量4.4t,4.5M电缆CWC-9x 不锈钢动载模块,容量9t,9M电缆CWC-13.6x 不锈钢动载模块,容量13.6t,9M电缆CWC-20x 不锈钢动载模块,容量20t,9M电缆GW/UW/PGW/GWA/PGWA-X模块产品型号产品描述GW-15x 防爆GW不锈钢称重模块,容量15t,,13M电缆GW-20x 防爆GW不锈钢称重模块,容量20t,,13M电缆GW-30x 防爆GW不锈钢称重模块,容量30t,,13M电缆GW-50x 防爆GW不锈钢称重模块,容量50t,,13M电缆GW-100x 防爆GW不锈钢称重模块,容量100t,,13M电缆GW-200x 防爆GW不锈钢称重模块,容量200t,,20M电缆GW-250x 防爆GW不锈钢称重模块,容量250t,,20M电缆GW-300x 防爆GW不锈钢称重模块,容量300t,,30M电缆GW-400x 防爆GW不锈钢称重模块,容量400t,,30M电缆GW-500x 防爆GW不锈钢称重模块,容量500t,,30M电缆GWA-15x 防爆GWA称重模块,容量15t,,13M电缆GWA-20x 防爆GWA称重模块,容量20t,,13M电缆GWA-30x 防爆GWA称重模块,容量30t,,13M电缆GWA-50x 防爆GWA称重模块,容量50t,,13M电缆GWA-100x 防爆GWA称重模块,容量100t,,13M电缆GWA-200x 防爆GWA称重模块,容量200t,,20M电缆GWA-250x 防爆GWA称重模块,容量250t,,20M电缆GWA-300x 防爆GWA称重模块,容量300t,,30M电缆GWA-400x 防爆GWA称重模块,容量400t,,30M电缆GWA-500x 防爆GWA称重模块,容量500t,,30M电缆产品型号产品描述UW-5x 防爆UW不锈钢称重模块,容量5kg,,3M电缆UW-10x 防爆UW不锈钢称重模块,容量10kg,,3M电缆UW-20x 防爆UW不锈钢称重模块,容量20kg,,3M电缆UW-50x 防爆UW不锈钢称重模块,容量50kg,,3M电缆UW-75x 防爆UW不锈钢称重模块,容量75kg,,3M电缆UW-100x 防爆UW不锈钢称重模块,容量100kg,,3M电缆UW-200x 防爆UW不锈钢称重模块,容量200kg,,3M电缆UW-300x 防爆UW不锈钢称重模块,容量300kg,,3M电缆UW-500x 防爆UW不锈钢称重模块,容量500kg,,3M电缆瑞士METTLER TOLEDO梅特勒托利多仪表类型料罐/料仓/定量打包秤专用仪表IND331/IND131系列称重仪表称重终端面板式IND331 33P100000000000 IND331 33P10000B000000 IND331 33P100000D00000 IND331 33P100000B00000 IND331 33P100000A00000 IND331 33P100000P00000 称重终端防尘式IND331 33H100000000J00 IND331 33H100000D00J00 IND331 33H100000B00J00 IND331 33H100000A00J00 IND331 33H100000P00J00称重终端导轨式IND131 13D100000000000 IND131 13D100000D00000 IND131 13D100000B00000 IND131 13D100000P00000 IND131 13D100000K00000IND131接线盒式IND131 13B100000000000 IND131 13B10000B000000 IND131 13B100000D00000 IND131 13B100000B00000 IND131 13B100000A00000 IND131 13B100000P00000 IND131 13D100000K00000IND245系列称重仪表称重终端普通型IND245 245G13000010J00 IND245 245G14000010J00 IND245 245G13001010J00 IND245 245G14001010J00 IND245 245G13002010J00 IND245 245G13003010J00 IND245 245G13004010J00 IND245 245G13010010J00 IND245 245G13011010J00 IND245 245G10001130J00 IND245 245G10002130J00 IND245 245G10011130J00 IND245 245G10012130J00称重终端防尘型IND245 245H13000010J00 IND245 245H14000010J00 IND245 245H13001010J00 IND245 245H14001010J00 IND245 245H13002010J00 IND245 245H13003010J00IND245 245H13004010J00 IND245 245H13010010J00 IND245 245H13011010J00XK3123 IND320专用仪表产品型号产品描述IND320 32E100000000023，基本型,防护等级IP65IND320 32E10000B000023，配料型，防护等级IP65IND320 32E10000B001023，减量法，防护等级IP65IND320 32E10000A000023，模拟量型，防护等级IP65 IND320 32E10001B000023，配料型，防护等级IP65IND320 32E100000C00023，基本型，canopen接口，IP65 IND320 32E10000BC00023，配料型，canopen接口，IP65 应用领域IND320系列称重仪表广泛应用于：土建筑和建筑路面机械称重仪表技术参数瑞士METTLER TOLEDO梅特勒托利多接线盒类型接线盒AJB模拟类AJB-005 五孔模拟接线盒(不锈钢外壳)AJB-007 七孔模拟接线盒(不锈钢外壳)AJB-003 三孔模拟接线盒(不锈钢外壳)AJB-015接线盒DJB数字类DJB-004 四孔模拟接线盒(不锈钢外壳)DJB-005 五孔模拟接线盒(不锈钢外壳)DJB-006 六孔模拟接线盒(不锈钢外壳)DJB-007 七孔模拟接线盒(不锈钢外壳)接线盒AJB-X防爆类AJB-005X 防爆五孔模拟接线盒(不锈钢外壳)AJB-007X 防爆七孔模拟接线盒(不锈钢外壳)AJB-003X 防爆三孔模拟接线盒(不锈钢外壳)DJB-005X 防爆五孔模拟接线盒(不锈钢外壳)DJB-007X 防爆七孔模拟接线盒(不锈钢外壳)AJB-005N 五孔模拟接线盒(配新结构)AJB-007N 七孔模拟接线盒(配新结构)AJB-006N 六孔模拟接线盒(配新结构)AJB-003N 三孔模拟接线盒(配新结构)接线盒DJB-N数字类DJB-005N 五孔模拟接线盒(配新结构)DJB-007N 七孔模拟接线盒(配新结构)DJB-006N 六孔模拟接线盒(配新结构)DJB-004N 四孔模拟接线盒(配新结构)接线盒DJB-C数字类DJB-004C 四孔数字接线盒(GDD.用于标准汽车衡) DJB-005C 五孔数字接线盒(GDD.用于标准汽车衡) DJB-006C 六孔数字接线盒(GDD.用于标准汽车衡) DJB-007C 七孔数字接线盒(GDD.用于标准汽车衡)接线盒DJB-CN数字类DJB-004CN 四孔数字接线盒(GDD.用于新结构汽车衡) DJB-005CN 五孔数字接线盒(GDD.用于新结构汽车衡) DJB-006CN 六孔数字接线盒(GDD.用于新结构汽车衡)。
- 1、下载文档前请自行甄别文档内容的完整性，平台不提供额外的编辑、内容补充、找答案等附加服务。
- 2、"仅部分预览"的文档,不可在线预览部分如存在完整性等问题,可反馈申请退款(可完整预览的文档不适用该条件!)。
- 3、如文档侵犯您的权益，请联系客服反馈,我们会尽快为您处理(人工客服工作时间：9:00-18:30)。
Laumas AM-200kg称重传感器
广州南创房工
意大利Laumas有限公司在意大利成立，是一个基于应变式称重传感器，意大利LAUMAS这款电子产品自1984年以来跻身于工业称重市场。
在工业称重及配料领域有25年的丰富经验。
数字指标，吊秤称重系统，自成立以来，LAUMAS称重传感器的产品远销38个国家，在多个国家设立了分支机构或办事处，生产基地遍布美洲、东欧、中国等地；并在中国设立了广州南创传感器事业部，可为用户的实验生产提供最佳的服务与解决方案。
LAUMAS称重传感器分为：单点式、剪切（悬臂）梁式、弯曲梁式、拉力式、柱压式、轴销式、锚式、钢丝绳测力限重器式、增辐放大器式等。
LAUMAS称重传感器详细型号如下：
CTOL 拉式称重传感器(load cells)
CLK 拉压式称重传感器(load cells)
COL 压式称重传感器(load cells)
COK 压式称重传感器(load cells)
CO 压式称重传感器(load cells)
CK 压式称重传感器(load cells)
CBX 压式称重传感器(load cells)
CBLS 压式称重传感器(load cells)
PTC 单点式称重传感器(load cells)
PTAI 单点式称重传感器(load cells)
PT 单点式称重传感器(load cells)
PRC 单点式称重传感器(load cells)
PR 单点式称重传感器(load cells)
PL 单点式称重传感器(load cells)
PEI 单点式称重传感器(load cells)
PEC 单点式称重传感器(load cells)
PE 单点式称重传感器(load cells)
AZL 单点式称重传感器(load cells)
AZ 单点式称重传感器(load cells)
AU 单点式称重传感器(load cells)
ATL 单点式称重传感器(load cells)
AS 单点式称重传感器(load cells)
AR 单点式称重传感器(load cells)
APL 单点式称重传感器(load cells)
AP 单点式称重传感器(load cells)
AM 单点式称重传感器(load cells)
ALL 单点式称重传感器(load cells)
AL 单点式称重传感器(load cells)
TRP压力传感器(Pressure transducer) FUN 称重传感器(load cells)
CA 轮辐式称重传感器(load cells)
LAU 轴销式称重传感器(load cells) FCOL 波纹管称重传感器(load cells) FCK 波纹管称重传感器(load cells) FCAX 波纹管称重传感器(load cells) FCAL 波纹管称重传感器(load cells) FUN 称重传感器(load cells)
CA 轮辐式称重传感器(load cells)
LAU 轴销式称重传感器(load cells) FTK 剪切梁式称重传感器(load cells) FTL 剪切梁式称重传感器(load cells) FTO 剪切梁式称重传感器(load cells) FTP 剪切梁式称重传感器(load cells) FTZ 剪切梁式称重传感器(load cells）
Laumas AM-200kg称重传感器图片：
Laumas AM-200kg称重传感器详细型号如下：
1.单点式称重传感器
AS-0.25kg,AS-0.5kg
AL-3kg,AL-15kg,AL-30kg
AF-5kg,AF-15kg
AU-3kg,AU-6kg,AU-15kg,AU-30kg,AU-50kg
PR-6kg,PR-15kg,PR-30kg,PR-50kg
PRIR-15kg,PRIR-30kg
AZ-10kg,AZ-30kg,AZ-50kg,AZ-100kg
PT-50kg,PT-75kg,PT-100kg,PT-150kg
PTAI-30kg,PTAI-50kg,PTAI-100kg,PTAI-200kg
AM-60kg,AM-150kg,AM-300kg
AP-50kg,AP-150kg,AP-300kg
PE-75kg,PE-150kg,PE-300kg,PE-500kg
AR-500kg,AR-1000kg
PL-500kg,PL-1000kg,PL-1800kg
AT-1000kg,AT-2000kg
2.压式称重传感器
CK-500kg,CK-1000kg
CBX-15000kg,CBX-30000kg,CBX-50000kg
CBL-250kg,CBL-500kg,CBL-1000kg,CBL-2500kg,CBL-5000kg,CBL-7500kg,CBL-1 0000kg,CBL-15000kg,CBL-30000kg,CBL-50000kg,CBL-100000kg
CBLS-200000kg,CBLS-300000kg,CBLS-500000kg,CBLS-750000kg
COK-15000kg,COK-35000kg,COK-50000kg
COL-15000kg,COL-30000kg,COL-60000kg
CO-25000kg
3.拉式称重传感器
TAL-10000kg称重传感器,TAL-10000kg
TBL-20000kg,TBL-30000kg,TBL-50000kg
4.拉压式称重传感器
CL-500kg,CL-1000kg,CL-2000kg,CL-5000kg,CL-10000kg,CL-20000kg,CL-30000 kg,CL-60000kg,CL-100000kg,CL-150000kg,CL-200000kg
CLK-2000kg,CLK-5000kg,CLK-10000kg,CLK-20000kg
SA-15kg,SA-30kg,SA-60kg,SA-150kg,SA-300kg
CTOL-50kg,CTOL-100kg,CTOL-200kg,CTOL-300kg,CTOL-500kg,CTOL-1000kg,CTO L-2500kg,CTOL-5000kg
CTL-100kg,CTL-200kg,CTL-300kg,CTL-500kg,CTL-1000kg,CTL-2500kg,CTL-500 0kg,CTL-7500kg,CTL-10000kg,CTL-12500kg
5.剪切式称重传感器
FTA-750kg,FTA-1200kg,FTA-1500kg,FTA-3000kg,FTA-5000kg
FTL-300kg,FTL-500kg,FTL-1000kg,FTL-2000kg,FTL-3000kg,FTL-50000kg
FTK-500kg,FTK-1000kg,FTK-2000kg
FTO-75kg,FTO-150kg,FTO-300kg,FTO-500kg,FTO-1000kg,FTO-2000kg,FTO-5000 kg,FTO-10000kg
FTOL-2000kg,FTOL-5000kg
LAU-5000kg,LAU-10000kg,LAU-20000kg
6.悬臂梁式称重传感器
FCOL-20kg,FCOL-50kg,FCOL-100kg,FCOL-200kg,FCOL-350kg,FCOL-500kg
FCL-10kg,FCL-20kg,FCL-50kg,FCL-100kg,FCL-200kg
FCA-500kg,FCA-750kg,FCA-1000kg
FCAL-30kg,FCAL-50kg,FCAL-75kg,FCAL-150kg,FCAL-300kg
CA-30t,CA-50t,CA-75t,CA-100t,CA-125t,CA-150t,CA-180t,CA-250t
FUN-1000/1000kg,2000/1000kg,5000/2000kg,10000/3000kg,20000/5000kg
7.称重仪表
LCD-1,TL,TD RS485,TPZ,TPS-JOLLYTPS,WE RS485,JOLLY,P-WI,PWS
DOS2005,W60.000,PROFIBUS,WT60.000.WT60.000M,WL60.000,WR60.000
8.遥控显示仪表
PC-PL
Laumas AM-200kg称重传感器技术参数以《OIML60号国际建议》92年版为基础，意大利LAUMAS的最新具体变化可查看《JJG669—Laumas广州南创传感器事业部
检定规程》。