HT201V01-101-640×480-XXcd-20060310

PROPRIETARY NOTE THIS SPECIFICATION IS THE PROPERTY OF BOE TFT-LCD SBU AND SHALL NOT BE REPRODUCED OR COPIED WITHOUT THE WRITTEN PERMISSION OF BOE TFTLCD SBU AND MUST BE RETURNED TO BOE TFT-LCD SBU UPON ITS REQUESTTITLE : HT201V01-101 Product Specification Rev. ABOE TFT-LCD SBUBEIJING BOE OPTOELECTRONICS TECHNOLOGY BOE HYDIS TECHNOLOGYSPEC. NUMBER S864-1252 B2005-C001-O(1/3)PRODUCT GROUP TFT-LCDREV. AISSUE DATE 2006. 3.10.PAGE 1 OF 26 A4(210 X 297)PRODUCT GROUPTFT LCD PRODUCTREV AISSUE DATE 06. 3.10.REVISION HISTORYREV. 0 AE0602-F029ECN NO.DESCRIPTION OF CHANGES Initial Release1. Add Viewing Angle (CR>5) : 80/80/80/80 TypDATE 05.10.24. 06.02.24.PREPARED W.K. Chang M.S. KangSPEC. NUMBER S864-1252 B2005-C001-O(2/3)SPEC. TITLE HT201V01-101 Product SpecificationPAGE 2 OF 26 A4(210 X 297)PRODUCT GROUPTFT- LCD PRODUCTREV AISSUE DATE 06. 3.10.ContentsNoREVISIONS HISTORY CONTENTS 1 GENERAL DESCRIPTION 1.1 Introduction 1.2 Features 1.3 Applications 1.4 General Specification 2 3 ABSOLUTE MAXIMUM RATINGS ELECTRICAL SPECIFICATIONS 3.1 TFT LCD Module 3.2 Back Light Unit 4 INTERFACE CONNECTION 4.1 Module Input Signal & power 4.2 Back Light Interface Connection 4.3 Data Format 5 SIGNAL TIMING SPECIFICATIONS 5.1 Timing Parameter 5.2 Signal Timing Waveform 5.3 Input Signals, Basic Display Colors & Cray Scale Of Colors 5.4 Power Sequence 6 7 OPTICAL SPECIFICATIONS MECHANICAL CHARACTERISTICS 7.1 Dimensional Requirements 7.2 Mounting 7.3 Anti-Glare and Polarizer Hardness 7.4 Light Leakage 8 9 10 RELIABLITY PRODUCT SERIAL NUMBER PACKING 10.1 Packing Order 10.2 Packing Note 10.3 Box Label 11 12 HANDING & CAUTIONS APPENDIX 23 24 19 20 21 16 18 12 9 6 7ITEMPage2 3 4SPEC. NUMBER S864-1252 B2005-C001-O(3/3)SPEC. TITLE HT201V01-101 Product SpecificationPAGE 3 OF 26 A4(210 X 297)PRODUCT GROUPTFT- LCD PRODUCTREV AISSUE DATE 06. 3.10.1.0 GENERAL DESCRIPTION1.1 Introduction HT201V01-101 is a color active matrix TFT LCD module using amorphous silicon TFT's (Thin Film Transistors) as an active switching devices. This module has a 20.1 inch diagonally measured active area with VGA resolutions (640 horizontal by 480 vertical pixel array). Each pixel is divided into RED, GREEN, BLUE dots which are arranged in vertical stripe and this module can display 16,777,216 colors. The TFT-LCD panel used for this module is adapted for a low reflection and higher color type.C N 21 C N 22 C N 23RGB TTL8bit(50pin)Source Driver CircuitS1 S640 G1LVDS TxGate Driver CircuitCNTiming Controller(LVDS Rx + RSDS)+5.0VTFT - LCD Panel(640 × RGB × 480 pixels)G480C N 24 C N 25 C N 26Power Circuit Block(6 CCFL Top Bottom Edge Type)1.2 Features z TTL Interface with 1 pixel / clock z High-speed response z Low power consumption z 8-bit color depth, display 16,777,216 colors z Incorporated edge type back-light (6 lamps) z High luminance and contrast ratio, low reflection and wide viewing angle z DE (Data Enable) only z RoHS Compliant SPEC. NUMBER S864-1252 B2005-C001-O(3/3) SPEC. TITLE HT201V01-101 Product Specification PAGE 4 OF 26 A4(210 X 297)PRODUCT GROUPTFT- LCD PRODUCT 1.3 Application z TV useREV AISSUE DATE 06. 3.10.1.4 General Specification The followings are general specifications at the model HT201V01-101. <Table 1. General Specifications> Parameter Active area Number of pixels Pixel pitch Pixel arrangement Display colors Display mode Dimensional outline Weight Surface Treatment Back-light Specification 408(H) × 306(V) 640(H) × 480(V) 0.6375(H) × 0.6375(V) RGB Vertical stripe 16,777,216 Normally White 448.6 × 339.6 × 25.0(max.) 3200 (typ.) Haze 25%, 3H Top/Bottom edge side, 6-CCFL type mm gram colors Unit mm pixels mm RemarksSPEC. NUMBER S864-1252 B2005-C001-O(3/3)SPEC. TITLE HT201V01-101 Product SpecificationPAGE 5 OF 26 A4(210 X 297)PRODUCT GROUPTFT- LCD PRODUCTREV AISSUE DATE 06. 3.10.2.0 ABSOLUTE MAXIMUM RATINGSThe followings are maximum values which, if exceed, may cause faulty operation or damage to the unit. The operational and non-operational maximum voltage and current values are listed in Table 2. < Table 2. Absolute Maximum Ratings> [VSS=GND=0V] Parameter Power Supply Voltage Logic Supply Voltage Back-light Lamp Current Back-light Lamp frequency Operating Temperature Storage Temperature Symbol VDD VIN IBL FL TOP TST Min. VSS-0.5 VSS-0.3 3 40 0 -20 Max. 6.5 VDD+0.3 7 70 +50 +60 Unit V V mA kHz ℃ ℃ Note 1 Note 1 Remarks Ta = 25 ℃Note : 1. Temperature and relative humidity range are shown in the figure below. Wet bulb temperature should be 39 ℃ max. and no condensation of water.100 90 80Relative Humidity (%RH)60O p e ra tin g R a n g e4020S to ra g e R a n g e5 -2 0 0 20 40 60 80T e m p e ra tu re (˚ C)SPEC. NUMBER S864-1252 B2005-C001-O(3/3)SPEC. TITLE HT201V01-101 Product SpecificationPAGE 6 OF 26 A4(210 X 297)PRODUCT GROUPTFT- LCD PRODUCTREV AISSUE DATE 06. 3.10.3.0 ELECTRICAL SPECIFICATIONS3.1 TFT LCD Module < Table 3. Electrical Specifications > ParameterPower Supply Voltage Power Supply Current Rush current Back-light Lamp Voltage Back-light Lamp Current Back-light Lamp operating Frequency Lamp Start Up Voltage Lamp Life PD Power Consumption P BL P Total IRUSH VBL IBL FL Vs 3.0 40 50,000 3.25 29.4 32.7 5.5 ← 34.9 [Ta =25±2 ℃]SymbolVDDValues Min4.5 -Typ5.0 650 755 6.5 -Max5.5 1000 3.0UnitVdc mA A VrmsNotesNote 1 Note 27.0 70 1400 1700mArms kHz Vrms Vrms Hrs W W W IBL = 6.5mA Note 5 Note 3 25℃, Note 4 0℃, Note 4 IBL=6.5Note : 1. The supply voltage is measured and specified at the interface connector of LCM. The current draw and power consumption specified is for VDD=5.0V, Frame rate=60Hz and Clock frequency = 25.18MHz. Test Pattern of power supply current a) Typ : Black Pattern b) Max : Sub Dot Pattern 2. The duration of rush current is about 2ms and rising time of Power Input is 1ms(min) 3. The lamp frequency should be selected as different as possible from the horizontal synchronous frequency and its harmonics to avoid interference, which may cause line flow on the display 4. The voltage above this value should be applied to the lamps for more than 1 second to start-up. Otherwise the lamps may not be turned on. 5. Calculated value for reference (VBL × IBL) × 6 excluding inverter loss. SPEC. NUMBER S864-1252 B2005-C001-O(3/3) SPEC. TITLE HT201V01-101 Product Specification PAGE 7 OF 26 A4(210 X 297)PRODUCT GROUPTFT- LCD PRODUCTREV AISSUE DATE 06. 3.10.4.0INTERFACE CONNECTION.4.1 Module Input Signal & Power - Connector : Hirose FH12-50S-0.5SH or Equivalent User Side Connection ; FFC or FPC ( Thickness : 0.3mm & 0.5mm Pitch)Pin No1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25SymbolNC NC NC GND GND VCC VCC VCC VCC GND NC NC GND DE GND DCLK GND R7 R6 R5 R4 GND R3 R2 R1FunctionNO CONNECTION NO CONNECTION NO CONNECTION GROUND GROUNDRemarkPin No26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50SymbolR0 GND G7 G6 G5 G4 GND G3 G2 G1 G0 GND B7 B6 B5 B4 GND B3 B2 B1 B0 GND GND NC* NC*FunctionRED DATA GROUNDRemarkGREEN DATA (G7 : MSB)POWER SUPPLY ( + 5.0V )GROUNDGROUND NO CONNECTION NO CONNECTION GROUND DATA ENABLE GROUND DOT CLOCK GROUNDGREEN DATAGROUNDBLUE DATA (B7 : MSB)GROUNDRED DATA (R7 : MSB)BLUE DATAGROUND RED DATAGROUND GROUND NO CONNECTION NO CONNECTION* N.C : Do not Connect. These Pins are only for BOE HDIS internal Operations.SPEC. NUMBER S864-1252 B2005-C001-O(3/3)SPEC. TITLE HT201V01-101 Product SpecificationPAGE 8 OF 26 A4(210 X 297)PRODUCT GROUPTFT- LCD PRODUCT 4.2 Back-light Interface Connection CN21, 22, 23 CN24, 25, 26 Lamp Position Center Module Side Connector User Side Connector CN NO. CN23 CN26 PIN NO. 1 2 1 CN21 CN22 CN24 CN25 2 1 2 INPUT HOT COLD HOT COLD HOT COLDREV AISSUE DATE 06. 3.10.BHSR-02VS-1 (JST) or equivalent SM02-BHSS-1-TB (JST) or equivalent COLOR White White Pink Blue Blue Pink FUNCTION High Voltage Ground High Voltage Ground High Voltage GroundOuterAASPEC. NUMBER S864-1252 B2005-C001-O(3/3)SPEC. TITLE HT201V01-101 Product SpecificationPAGE 9 OF 26 A4(210 X 297)PRODUCT GROUPTFT- LCD PRODUCT 4.3 Data Input Format ODD (1,1) EVEN (2,1)REV AISSUE DATE 06. 3.10.(639,1)(640,1)R G B R G BR G B R G B1 Pi xel= 3 D ot sR G BR G B R G B(1,480) (2,480)R G B R G B(639,480) (640,480)Display Position of Input Data (V-H)SPEC. NUMBER S864-1252 B2005-C001-O(3/3)SPEC. TITLE HT201V01-101 Product SpecificationPAGE 10 OF 26 A4(210 X 297)PRODUCT GROUPTFT- LCD PRODUCTREV AISSUE DATE 06. 3.10.5.0 SIGNAL TIMING SPECIFICATION5.1 Timing Parameters ( DE only mode) < Table 8. Timing Table > ITEM Clock Vertical Active Display Term Horizontal Active Display Term Symbol Frequency Frame Rate Valid Total Valid Total 1/tCLK fV tVV tVT tHV tHT Min 25 47 485 714 Typ 25.18 60 480 525 640 800 Max 39 75 627 1056 tCLK Unit MHz Hz tHP NoteNotes: This product is DE only mode. The input of Hsync & Vsync signal does not have an effect on normal operation.SPEC. NUMBER S864-1252 B2005-C001-O(3/3)SPEC. TITLE HT201V01-101 Product SpecificationPAGE 11 OF 26 A4(210 X 297)PRODUCT GROUPTFT- LCD PRODUCTREV AISSUE DATE 06. 3.10.5.2 Signal Timing Waveformt VT t VVDEt HTCLOCKtCLK t HT t HVDEDATAVALID DATA (640clocks)SPEC. NUMBER S864-1252 B2005-C001-O(3/3)SPEC. TITLE HT201V01-101 Product SpecificationPAGE 12 OF 26 A4(210 X 297)PRODUCT GROUPTFT- LCD PRODUCT 5.3 Input Signals, Basic Display Colors & Gray Scale Of ColorsInput Data Signal Green DataR1 0 0 0 0 1 1 1 1 0 0 1REV AISSUE DATE 06. 3.10.Color & Gray ScaleBlack Blue Green Cyan Red Magenta Yellow White Black △ Darker △ ▽ Brighter ▽ Red Black △ Darker △ ▽ Brighter ▽ Green Black △ Darker △ ▽ Brighter ▽ Blue Black △ Darker △ ▽ Brighter ▽ White R7 0 0 0 0 1 1 1 1 0 0 0 R6 0 0 0 0 1 1 1 1 0 0 0Red DataR5 0 0 0 0 1 1 1 1 0 0 0 R4 R3 0 0 0 0 0 0 0 0 1 1 1 1 1 1 1 1 0 0 0 0 0 0 ↑ ↓ 1 1 1 1 1 1 0 0 0 0 0 0 ↑ ↓ 0 0 0 0 0 0 0 0 0 0 0 0 ↑ ↓ 0 0 0 0 0 0 0 0 0 0 0 0 ↑ ↓ 1 1 1 1 1 1 R2 0 0 0 0 1 1 1 1 0 0 0Blue DataB6 0 1 0 1 0 1 0 1 0 0 0 B5 0 1 0 1 0 1 0 1 0 0 0 B4 B3 0 0 1 1 0 0 1 1 0 0 1 1 0 0 1 1 0 0 0 0 0 0 ↑ ↓ 0 0 0 0 0 0 0 0 0 0 0 0 ↑ ↓ 0 0 0 0 0 0 0 0 0 0 0 0 ↑ ↓ 1 1 1 1 1 1 0 0 0 0 0 0 ↑ ↓ 1 1 1 1 1 1 B2 0 1 0 1 0 1 0 1 0 0 0 B1 0 1 0 1 0 1 0 1 0 0 0 B0 0 1 0 1 0 1 0 1 0 0 0Basic ColorsGray Scale of RedGray Scale of Green1 1 1 0 0 01 1 1 0 0 01 1 1 0 0 01 1 1 0 0 00 1 1 0 0 0Gray Scale of Blue0 0 0 0 0 00 0 0 0 0 00 0 0 0 0 00 0 0 0 0 00 0 0 0 0 0Gray Scale of White0 0 0 0 0 00 0 0 0 0 00 0 0 0 0 00 0 0 0 0 00 0 0 0 0 11 1 1 1 1 1 1 1 11 0 1 1 1 1R0 G7 G6 G5 G4 G3 G2 G1 G0 B7 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 1 0 1 1 1 1 1 1 1 1 0 0 1 1 1 1 1 1 1 1 1 1 0 0 0 0 0 0 0 0 0 1 0 0 0 0 0 0 0 0 1 1 1 1 1 1 1 1 1 1 0 1 1 1 1 1 1 1 1 1 1 0 0 0 0 0 0 0 0 0 0 1 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 ↑ ↓ 1 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 1 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 1 0 0 0 0 0 0 0 0 1 0 0 ↑ ↓ 0 1 1 1 1 1 1 0 1 0 0 1 1 1 1 1 1 1 0 0 0 1 1 1 1 1 1 1 1 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 ↑ ↓ 0 0 0 0 0 0 0 0 0 1 0 0 0 0 0 0 0 0 0 1 0 0 0 0 0 0 0 0 0 1 0 0 0 0 0 0 0 0 0 0 1 0 0 0 0 0 0 0 1 0 0 0 0 0 0 0 0 1 0 0 ↑ ↓ 1 1 1 1 1 1 1 0 1 1 0 1 1 1 1 1 1 1 0 1 1 1 1 1 1 1 1 1 1 10 0 0 0 0 00 0 0 0 0 00 0 0 0 0 00 0 0 0 0 00 0 0 0 0 00 0 0 0 0 00 0 0 0 0 00 0 0 0 0 00 0 0 0 0 10 0 0 0 1 01 1 1 0 0 01 1 1 0 0 01 1 1 0 0 00 1 1 0 0 11 0 1 0 1 01 1 1 1 1 11 0 1 1 1 0 1 1 1SPEC. NUMBER S864-1252 B2005-C001-O(3/3)SPEC. TITLE HT201V01-101 Product SpecificationPAGE 13 OF 26 A4(210 X 297)PRODUCT GROUPTFT- LCD PRODUCT 5.4 Power SequenceREV AISSUE DATE 06. 3.10.To prevent a latch-up or DC operation of the LCD module, the power on/off sequence shall be as shown in below0.9VDD 0.9VDD 0.1VDDPower Supply0V0.1VDDT1 T2 Valid0VT5T6Interface Signal ( Input Data )T3T4Inverter Signal ( B/L On/Off )0VParameter T1 T2 T3 T4 T5 T6Values Min 0.5 0.5 1 100 0.5 3.0 Typ Max 10 50 50 -Units ms ms s ms ms sNotes: 1. When the power supply VDD is 0V, Keep the level of input signals on the low or keep high impedance. 2. Do not keep the interface signal high impedance when power is on. 3. Back Light must be turn on after power for logic and interface signal are valid.SPEC. NUMBER S864-1252 B2005-C001-O(3/3)SPEC. TITLE HT201V01-101 Product SpecificationPAGE 14 OF 26 A4(210 X 297)PRODUCT GROUPTFT- LCD PRODUCTREV AISSUE DATE 06. 3.10.6.0 OPTICAL SPECIFICATIONThe test of Optical specifications shall be measured in a dark room (ambient luminance ≤ 1 lux and temperature = 25±2℃) with the equipment of Luminance meter system (Goniometer system and TOPCON BM-5) and test unit shall be located at an approximate distance 50cm from the LCD surface at a viewing angle of θ and Φ equal to 0°. We refer to θØ=0 (=θ3 ) as the 3 o’clock direction (the “right”), θØ=90 (= θ12 ) as the 12 o’clock direction (“upward”), θØ=180 (= θ9 ) as the 9 o’clock direction (“left”) and θØ=270(= θ6 ) as the 6 o’clock direction (“bottom”). While scanning θ and/or Ø, the center of the measuring spot on the Display surface shall stay fixed. The measurement shall be executed after 30 minutes warm-up period. VDD shall be 5.0V +/-10% at 25°C. Optimum viewing angle direction is 6 ’clock. Base Back-Light Lamp Current (IBL) is 6.5 mA on center lamp.[VDD = 5.0V, Frame rate = 60Hz, IBL=6.5mA Ta =25±2 ℃]ParameterHorizontal Vertical Horizontal Vertical Contrast ratio Luminance of White White luminance uniformity White Red Green Blue Response Time Rise DecaySymbol Condition MinΘ3 Θ9 Θ12 Θ6 Θ3 Θ9 Θ12 Θ6 CR Yw ΔY Wx Wy Rx Ry Gx Gy Bx By Tr Td CT Θ = 0° (Center) Normal Viewing Angle CR > 5 CR > 10 65 65 60 50 70 70 70 70 550 400 75 0.250 0.260 0.612 0.301 0.252 0.559 0.110 0.036 -Typ75 75 70 60 80 80 80 80 700 500 80 0.280 0.290 0.642 0.331 0.282 0.589 0.140 0.066 3 5 -Max-UnitDeg. Deg. Deg. Deg. Deg. Deg. Deg. Deg.RemarkViewing AngleNote 1Note 2 cd/m2 % 0.310 0.320 0.672 0.361 0.312 0.619 0.170 0.096 5 7 2.0 ms ms % Note 6 Note 7 Note 5 Note 3 Note 4Reproduction of colorCross TalkSPEC. NUMBER S864-1252 B2005-C001-O(3/3)SPEC. TITLE HT201V01-101 Product SpecificationPAGE 15 OF 26 A4(210 X 297)PRODUCT GROUPTFT- LCD PRODUCTREV AISSUE DATE 06. 3.10.Note :1. Viewing angle is the angle at which the contrast ratio is greater than 10. The viewing are determined for the horizontal or 3, 9 o’clock direction and the vertical or 6, 12 o’clock direction with respect to the optical axis which is normal to the LCD surface. 2. Contrast measurements shall be made at viewing angle of θ= 0° and at the center of the LCD surface. Luminance shall be measured with all pixels in the view field set first to white, then to the dark (black) state. (See FIGURE 1 shown in Appendix) Luminance Contrast Ratio (CR) is defined mathematically. Luminance when displaying a white raster Luminance when displaying a black rasterCR=3. Center Luminance of white is defined as the LCD surface. Luminance shall be measured with all pixels in the view field set first to white. This measurement shall be taken at the locations shown in FIGURE 2 for a total of the measurements per display. 4. The White luminance uniformity on LCD surface is then expressed as : ΔY = ( Minimum Luminance of 5points / Maximum Luminance of 5points ) * 100 (See FIGURE 2 shown in Appendix). 5. The color chromaticity coordinates specified in Table 4. shall be calculated from the spectral data measured with all pixels first in red, green, blue and white. Measurements shall be made at the center of the panel. 6. The electro-optical response time measurements shall be made as FIGURE 3 shown in Appendix by switching the “data” input signal ON and OFF. The times needed for the luminance to change from 10% to 90% is Td, and 90% to 10% is Tr. 7. Cross-Talk of one area of the LCD surface by another shall be measured by comparing the luminance (YA) of a 25mm diameter area, with all display pixels set to a gray level, to the luminance (YB) of that same area when any adjacent area is driven dark. (See FIGURE 4 shown in Appendix).SPEC. NUMBER S864-1252 B2005-C001-O(3/3)SPEC. TITLE HT201V01-101 Product SpecificationPAGE 16 OF 26 A4(210 X 297)PRODUCT GROUPTFT- LCD PRODUCTREV AISSUE DATE 06. 3.10.7.0 MECHANICAL CHARACTERISTICS7.1 Dimensional Requirements FIGURE 6 (located in Appendix) shows mechanical outlines for the model HT201V01-101. Other parameters are shown in Table 5. <Table 5. Dimensional Parameters> ParameterDimensional outline Weight Active area Pixel pitch Number of pixels Back-lightSpecification 448.6 × 339.6 × 25.0 (max.) 3200 (typ., 3500 max) 408(H) × 306(V) 0.6375(H) ×0.6375(V) 640(H) × 480(V) (1 pixel = R + G + B dots) Top / Bottom edge side 6-CCFL typeUnitmm gram mm mm pixels7.2 Mounting See FIGURE 5. (shown in Appendix)7.3 Anti-Glare and Polarizer Hardness. The surface of the LCD has an anti-glare coating to minimize reflection and a coating to reduce scratching.7.4 Light Leakage There shall not be visible light from the back-lighting system around the edges of the screen as seen from a distance 50cm from the screen with an overhead light level of 350 [lux.]SPEC. NUMBER S864-1252 B2005-C001-O(3/3)SPEC. TITLE HT201V01-101 Product SpecificationPAGE 17 OF 26 A4(210 X 297)PRODUCT GROUPTFT- LCD PRODUCTREV AISSUE DATE 06. 3.10.8.0 RELIABLITY TESTThe Reliability test items and its conditions are shown in below. <Table 6. Reliability Test Parameters > No 1 2 3 4 5 6 Test ItemsHigh temperature storage test Low temperature storage test High temperature & high humidity operation test High temperature operation test Low temperature operation test Thermal shock Ta = 60 ℃, 240 hrs Ta = -20 ℃, 240 hrs Ta = 50 ℃, 80%RH, 240hrs Ta = 50 ℃, 240hrs Ta = 0 ℃, 240hrs Ta = -20 ℃ ↔ 60 ℃ (0.5 hr), 100 cycle Frequency : 10 ~ 300 Hz, Sweep rate 30 minConditions7Vibration test (non-operating)Gravity / AMP : 1.5 G Sine Period Gravity : ±X, ±Y, ±Z 30 min : 50G8Shock test (non-operating)Pulse width : 11msec, Sine wave ±X, ±Y, ±Z Once for each direction Air : ±15kV , 150pF/330Ω ,100Point ,1time/Point9Electro-static discharge test Contact : ±8kV , 150pF/330Ω ,100Point , 1time/PointSPEC. NUMBER S864-1252 B2005-C001-O(3/3)SPEC. TITLE HT201V01-101 Product SpecificationPAGE 18 OF 26 A4(210 X 297)PRODUCT GROUPTFT- LCD PRODUCTREV AISSUE DATE 06. 3.10.9.0 Product Serial NumberSPEC. NUMBER S864-1252 B2005-C001-O(3/3)SPEC. TITLE HT201V01-101 Product SpecificationPAGE 19 OF 26 A4(210 X 297)PRODUCT GROUPTFT- LCD PRODUCTREV AISSUE DATE 06. 3.10.10.0 PACKING INFORMATIONBOE provides the standard shipping container for customers, unless customer specifies their packing information. The standard packing method and Barcode information are shown in below. 10.1 Packing OrderPut Pad into the box.As shown in the figure, place the Modules bundled by shielding bag in the box.After sealing the box, attach Packing Label on the attach position sign area of the box.Place a cover on the top of the box.SPEC. NUMBER S864-1252 B2005-C001-O(3/3)SPEC. TITLE HT201V01-101 Product SpecificationPAGE 20 OF 26 A4(210 X 297)PRODUCT GROUPTFT- LCD PRODUCTREV AISSUE DATE 06. 3.10.10.2 Packing Note y Box Dimension : 346mm(W) × 526mm(D) × 448mm(H) y Package Quantity in one Box : 5pcs 10.3 Box label y Label Size : 108 mm (L) × 56 mm (W) y Contents Model : HT201V01 Q`ty : Module Q`ty in one box Serial No. : Box Serial No. See next page for detail description. Date : Packing Date FG Code : FG Code of ProductHT201V01- 101 00000000000005 2005.02.22.00 Type0 0 00 0 Grade Line Year Month0 00000 ITEM-CODE Serial_noFG CODESPEC. NUMBER S864-1252 B2005-C001-O(3/3)SPEC. TITLE HT201V01-101 Product SpecificationPAGE 21 OF 26 A4(210 X 297)PRODUCT GROUPTFT- LCD PRODUCTREV AISSUE DATE 06. 3.10.11.0 HANDLING & CAUTIONS(1) Cautions when taking out the module y Pick the pouch only, when taking out module from a shipping package. (2) Cautions for handling the module y As the electrostatic discharges may break the LCD module, handle the LCD module with care. Peel a protection sheet off from the LCD panel surface as slowly as possible. y As the LCD panel and back - light element are made from fragile glass material, impulse and pressure to the LCD module should be avoided. y As the surface of the polarizer is very soft and easily scratched, use a soft dry cloth without chemicals for cleaning. y Do not pull the interface connector in or out while the LCD module is operating. y Put the module display side down on a flat horizontal plane. y Handle connectors and cables with care. (3) Cautions for the operation y When the module is operating, do not lose CLK, ENAB signals. If any one of these signals is lost, the LCD panel would be damaged. y Obey the supply voltage sequence. If wrong sequence is applied, the module would be damaged. (4) Cautions for the atmosphere y Dew drop atmosphere should be avoided. y Do not store and/or operate the LCD module in a high temperature and/or humidity atmosphere. Storage in an electro-conductive polymer packing pouch and under relatively low temperature atmosphere is recommended. (5) Cautions for the module characteristics y Do not apply fixed pattern data signal to the LCD module at product aging. y Applying fixed pattern for a long time may cause image sticking. (6) Other cautions y Do not disassemble and/or re-assemble LCD module. y Do not re-adjust variable resistor or switch etc. yWhen returning the module for repair or etc., Please pack the module not to be broken. We recommend to use the original shipping packages.SPEC. NUMBER S864-1252 B2005-C001-O(3/3)SPEC. TITLE HT201V01-101 Product SpecificationPAGE 22 OF 26 A4(210 X 297)PRODUCT GROUPTFT- LCD PRODUCTREV AISSUE DATE 06. 3.10.12.0 APPENDIXFigure 1. Measurement Set Up(L = 5 0 c m )Figure 2. White Luminance and Uniformity Measurement Locations (5 points)160 320 480360240120SPEC. NUMBER S864-1252 B2005-C001-O(3/3)SPEC. TITLE HT201V01-101 Product SpecificationPAGE 23 OF 26 A4(210 X 297)PRODUCT GROUPTFT- LCD PRODUCT Figure 3. Response Time Testing Low Gray (Dark) Electro-Optical Response Td 100% 90% High Gray (Bright)REV AISSUE DATE 06. 3.10.Low Gray (Dark) Tr10% 0% Figure 4. Cross Modulation Test DescriptionVIEW AREA VIEW AREA(160,120) (480,120)TimeL31(160,360) (480,360)YB (240, 560)YA (240,560) Cross-Talk (%) = YB - YA YAL0× 100Where: YA = Initial luminance of measured area (cd/m2) YB = Subsequent luminance of measured area (cd/m2) The location measured will be exactly the same in both patternsSPEC. NUMBER S864-1252 B2005-C001-O(3/3)SPEC. TITLE HT201V01-101 Product SpecificationPAGE 24 OF 26 A4(210 X 297)PRODUCT GROUPTFT- LCD PRODUCTREV AISSUE DATE 06. 3.10.Figure 5. TFT-LCD Module Outline Dimensions (Front view)SPEC. NUMBER S864-1252 B2005-C001-O(3/3)SPEC. TITLE HT201V01-101 Product SpecificationPAGE 25 OF 26 A4(210 X 297)PRODUCT GROUPTFT- LCD PRODUCTREV AISSUE DATE 06. 3.10.Figure 6. TFT-LCD Module Outline Dimensions (Rear view)▶4.GENERAL TOLERANCE: ± 0.5 3.OTHER SPECIFICATION: REFERS TO SPEC SHEET MP CONNECTOR : BHSR-02VS-1 (JST) OR EQUIVALENT 1.I/F CONNECTOR : FH12-50S-0.5SH (HIROSE) OR EQUIVALENT NOTESPEC. NUMBER S864-1252 B2005-C001-O(3/3)SPEC. TITLE HT201V01-101 Product SpecificationPAGE 26 OF 26 A4(210 X 297)。