模具英语专业术语
模具英语专业术语
模具英语专业术语模具的分类:
冲压模(五金模): stamping die
分离模: cutting die
成形模: forming die
塑胶模: plastics mold
注射模: injection mold
压缩模: compression mold
铸塑模: transfer mold
吹塑模: blow mold
吸塑模: suck mold
铸造模: casting die
砂型铸造: sand casting
压铸模: die casting
锻造模: forging die
塑胶模具术语
一、入水:gate
进入位(入水点):gate location
水口形式:gate type
大水口(侧浇口): edge gate
潜水口: sub-gate
薄膜式水口: film gate
牛角式潜水口: banana gate
扇形水口: fan gate
环形水口: ring gate
二次水口:
细水口:pin-point gate
水口大小:gate size
转水口:switching runner/gate
唧嘴口径:sprue diameter
直接水口: direct gate
二、流道: runner
热流道:hot runner,hot manifold
热嘴冷流道: hot sprue/cold runner
唧嘴直流: direct sprue gate
圆形(整圆/半圆)流道:round(full/half) runner
矩形流道: rectangle runner
梯形流道: trapezoid runner
U形流道: U shape runner
流道电脑分析(模流分析):mold flow analysis
流道平衡: runner balance
热嘴:hot sprue/tip
热流道板:hot manifold
发热管:cartridge heater
探针: thermocouples
插头:connector plug
插座:connector socket
密封/封料:seal
三、运水:water line
喉塞:line plug
喉管:tube
塑胶管:plastic tube
快速接头:jiffy quick connector plug/socket 四、模具零件:mold components 三板模(细水口模):3-plate mold
二板模(大水口模):2-plate mold
热流道模具: hot-runner/manifold mold
叠层模: stacked mold
边钉/导边:leader pin/guide pin
边司/导套:guide pin/guide bushing
直导套:shoulder guide bushing
有托导套:straight guide bushing
中托司:ejector guide bush
中托边:ejector guide pin
回针: return pin
面板: top clamp plate
A板: A plate
推板:stripper plate
B板: B plate
托板:support plate
方铁: spacer block
加高方铁: higher spacer block
顶针固定板:ejector retainner plate
顶针板:ejector plate
底板: bottom clamp plate
螺丝:screw
杯头螺丝: socket cup head screw
平头螺丝: socket flat head screw
机米螺丝:
外六角头螺丝: bolt
栓打螺丝(等高螺丝):S.H.S.B
管钉:dowel pin
开模槽:ply bar socket
内模管位(模仁互锁):core/cavity inter-lock
顶针:ejector pin
司筒:ejector sleeve
司筒针:sleeve ejector pin
缩呵:movable core,return core, core puller 扣机(尼龙拉勾):nylon latch lock
斜顶:lifter
模胚(架):mold base
上内模:cavity insert
下内模:core insert
行位(滑块):slide
行位扣:
镶件:insert
压座/斜鸡:wedge
耐磨板/油板:wear plate
压条:gib
撑头: support pillar
唧嘴:sprue bushing
挡板:stop plate
定位圈(法兰):locating ring
锁扣(模锁):latch
扣鸡:parting lock set
推杆:push bar
顶板:eracuretun
活动臂:lever arm
分流锥:spure sperader
水口司:bush
垃圾钉:stop pin
隔片:buffle
弹弓柱:spring rod
弹弓:die spring
型腔(前模仁): cavity
型芯(后模仁): core
镶针:insert pin
销子(销钉):dowel pin
波子弹弓:ball catch
喉塞(堵头): pipe plug
锁模块:lock plate
斜顶杆:angle ejector rod
斜顶针:angle from pin
尼龙拉勾:parting locks
活动臂:lever arm
复位键、提前回杆:early return bar
气阀:valves
斜导边(斜导柱):angle pin
油缸: hydraulic cylinder
液压马达: hydraulic motor
齿轮: gear
轴承: bear
术语:terms
承压平面平衡:parting surface support balance
分模面排气:parting line venting
回针碰料位:return pin and cavity interference
模总高超出啤机规格:mold base shut hight
顶针碰运水:water line interferes with ejector pin
料位出上/下模:part from cavity (core) side
模胚原身出料位:cavity direct cut on A-plate,core direct cut on B-plate. 不准用镶件:Do not use (core/cavity) insert
用铍铜做镶件:use beryllium copper insert
初步模图设计:preliminary mold design
正式模图设计:final mold design
反呵:reverse core
弹弓压缩量:spring compressed length
稳定性好:good stability,stable
强度不够:insufficient rigidity
均匀冷却:even cooling
扣模(粘模):sticking
顶白: stress mark
热膨胀:thero expansion
缩水: shrinkage
物料表: BOM
原料: raw materials
物料: materials
工程试模材料: material for engineering mold testing
成品: finished product
半成品: semi-finished product
公差:tolorance
铜公(电极):copper electrode
射料不足: short shot
缺口: nick
瑕疪(斑点): speck
亮斑: shine
银纹: splay
焦痕: gas mark
起鳞: delamination
冷块: cold slug
导色: blush
沟槽;凿槽: gouge
段面咬花: satin texture
证示线: witness line
专利: patent
沙砾: grit
细粒: granule=peuet=grain
抽粒机: grit maker
缓冲: cushion
不锈钢: stainless steel
镁铝合金: magnalium
镁金属: magnesium
钣金: metal plate
车/车床: lathe
铣床/铣床: mill
刨/刨床: plane
磨/磨床: grind
钻/钻床: drill
镗: boring
气泡: blinster
版次: revision
备注: remark
生产确认: production control confirmation 初审: checked by
核准: approved by
部门: department
电镀: plate
成型: molding
样品: sample
雕刻: engrave
蚀纹: texture
加硬: harden
热处理: heat treatment
淬火: quenching
回火: tempering
退火: annealing
碳化: carbonization
铬酸处理: chromate
阳性处理: anodize
氮化: nitrifying
模具常用术语中英文对照
模芯 Parting Core 耐落胶 Teflon Paste 局部视图 Partial View 偏移量 Offset 冷料 Cold Slag 水塞 Water Line Plug 线切割 Wire 撬模脚 Ppy Slot 轮廓 Contour 重新加工 Reworked 螺纹孔Tapping Hole 配件 Components 连接件 Fittings 补偿 Compensation 斜针 Angle Pin 平面度 Parallel 接合 Engage 倒角Chamfer 替换镶件Interchangeable Mold Inserts 模胚 Mold Base 指定吨位的注塑机 Specific Press 热嘴Hotnozzle 水嘴接头 Water Fitting 火花机 Edm 螺纹 Eyebolt Thread 熔接线 Weildline 回针 Stop Pin 压机 Press 二级顶出针 Sub-Leaderd Pin 嗮纹 Texturing 镶件 Mold Insert 梯形 Trapezoid
加硬 Harden 凸缘、法兰 Flange 唧嘴 Sprue 方铁 Spacer Block 设计筒图 Design Preliminary 顶针板 Ejector Plate 名称块表 Title Block 顶针底板 Ejector Retainer Plate 版本标识 Revision Level 垫板 Retainer Plate 材料清单 Stock List 后模镶针 Core Pin 制模 Build Mold 垃圾钉 Stop Pin 手动滑块 Hand Slide 有托顶针 Shoulder Ejector Pin 漏水测试 Leak Test 顶针板导套Guided Ejection Bushing 流道排气 Runner Vents 针板导柱 Guided Ejection Leader Pin 抛光 Draw Polish 唧嘴 Sprue Bushing 侧抽芯 Slide Action 三板模延伸式唧嘴 Extension Noozzle Bulishing 加强筋 Reinforcing 水口板导套 Runner Stripper Pin 三角撑 Gusset 定位圈(法兰)Locating Ring 柱子 Bossed 管钉(定位销)Dowel Pin 出模斜度 Draft 管状管钉 Tubular Dowel
模具专业英语词汇大全
模具专业英语词汇 A abrasion n. 磨损 abrasion resistance n. 耐磨损性 abrasive n. 磨料 accelerator n. 促进剂 accuracy n. 准确性 accurate die casting 精密压铸 air trap 积风 acrylic n. 丙烯酸 /压克力 ì active plate 活动板 additive n. 添加剂 adhere v. 黏附 adhesion n. 黏合 adhesive n. 胶粘剂 air-cushion eject-rod 气垫顶杆 air cushion plate 气垫板 air entrapment n. 困气 anneal v. 退火 assemble v. 总成 B back pressure 背压 bismuth mold 铋铸模 baffle plate 挡块 barrel n. 机筒 /料筒 / bending block 折刀 bottom block 下垫脚 bottom plate 下托板(底板) bushing bolck 衬套 barrel temperature 料筒温度 blush 发 blank through dies 漏件式落料模 burnishi blow molding n. 吹塑成型 blow molding machine n. 吹塑机 brittle adj. 脆性 bubble n. 气泡 burr 毛刺 button d by-product n. 副产品 C calendering n. 压延 carbon steel n. 碳素钢 casting n. 铸造 catalyst n. 催化剂 cavity n. 型腔 chemical resistance n. 耐化学腐蚀性 chip v. 削 /凿
电力专业常用英语词汇()
网易电力专业英语词汇(较全) 1)元件设备 三绕组变压器:three-column transformer ThrClnTrans 双绕组变压器:double-column transformer DblClmnTrans 电容器:Capacitor 并联电容器:shunt capacitor 电抗器:Reactor 母线:Busbar 输电线:TransmissionLine 发电厂:power plant 断路器:Breaker 刀闸(隔离开关):Isolator 分接头:tap 电动机:motor 2)状态参数 有功:active power 无功:reactive power 电流:current 容量:capacity 电压:voltage 档位:tap position 有功损耗:reactive loss 无功损耗:active loss 空载损耗:no-load loss 铁损:iron loss 铜损:copper loss 空载电流:no-load current 阻抗:impedance 正序阻抗:positive sequence impedance 负序阻抗:negative sequence impedance 零序阻抗:zero sequence impedance 无功负载:reactive load 或者QLoad 有功负载: active load PLoad 遥测:YC(telemetering) 遥信:YX 励磁电流(转子电流):magnetizing current 定子:stator 功角:power-angle
上限:upper limit 下限:lower limit 并列的:apposable 高压: high voltage 低压:low voltage 中压:middle voltage 电力系统 power system 发电机 generator 励磁 excitation 励磁器 excitor 电压 voltage 电流 current 母线 bus 变压器 transformer 升压变压器 step-up transformer 高压侧 high side 输电系统 power transmission system 输电线 transmission line 固定串联电容补偿fixed series capacitor compensation 稳定 stability 电压稳定 voltage stability 功角稳定 angle stability 暂态稳定 transient stability 电厂 power plant 能量输送 power transfer 交流 AC 装机容量 installed capacity 电网 power system 落点 drop point 开关站 switch station 双回同杆并架 double-circuit lines on the same tower 变电站 transformer substation 补偿度 degree of compensation 高抗 high voltage shunt reactor 无功补偿 reactive power compensation 故障 fault 调节 regulation 裕度 magin 三相故障 three phase fault 故障切除时间 fault clearing time 极限切除时间 critical clearing time 切机 generator triping
制造业工厂常用英文与缩写词汇大全
一:常用術語 Hon Hai 鴻海 CMM Component module move 機動元件整合 CEM Contract Manu faction service 合約委托代工 IBSC Internet Business Solution Center 國際互聯網應用中心 PCEG Personal Computer Enclosure group 個人電腦外設事業群(FOXTEQ)CCBG Connector& cable business group CPBG Competition business group ESBG Enterprise system business group 鴻富錦事業群 SABG system assembly business group 系統組裝事業群 NWE Net Work Enclosure NSE Network system enclosure NSG Network system group NFE Network flexible enclosure Foxcavity = HZ = Hong Zhun 鴻準 Stamping tool shop I 沖模一廠 Stamping tool shop II 沖模二廠 Prototype workshop 樣品中心 Steel factory 裁剪廠 PCE molding tooling workshop PCE塑模廠 Hua Nan test and measurement center 華南檢測中心 MPE mobile phone enclosure MPE MBE mobile phone and notebook enclosure 明塑厂 MGE Alloy magnesium alloy enclosure 鎂合金 Engineer standard 工標 Document center (database center)資料中心 Design Center 設計中心 Painting 烤漆(廠) Assembly組裝(廠) Stamping 沖壓(廠) Education and Training教育訓練 proposal improvement/creative suggestion提案改善 Technological exchange and study 技術交流研習會 Technology and Development Committee 技術發展委員會 BS Brain Storming 腦力激蕩 QCC Quality Control Circle 品質圈 PDCA Plan Do Check Action 計劃執行檢查總結 DCC delivery control center 交貨管制中心 3C Computer 電腦類產品 Consumer electronics 消費性電子產品 Communication 通訊類產品 Core value(核心价值) Love 愛心
模具专业术语英语单词
1)Designer-设计师。 2)Assembly drawing-模具组装图。 3)Mold layout-模具结构图。 4)2D product drawing-2D产品图。 5)3D product data-3D产品数据。 6)Part drawing-散件图。 7)Insert molding-镶件模。 8)2color mold/Double injection tool-双色模。 9)Hydraulic system-油/水压系统。 10)Parting line-分模线。 11)Air venting-排气槽。 12)Cooling system-冷却系统。 13)Screw-镙丝。 14)Hot runner system-热流道。 15)Valve gate-伐针入水口。 16)Fan gate-扇型入水口。 17)Pin point gate-针点进胶。 18)Moon gate/Banana gate-香蕉,象牙入水口。 19)Submarine gate-潜水口。 20)Injection machine tonnage-注塑机吨数。 21)Number of cavity-穴数。 22)Steel-钢材。 23)Copper-铜。 24)Tungsten copper-钨铜。 25)Beryllium copper-铍铜。 26)Hardening-加硬/淬火。 27)Tempering-回火。 28)Chroming-电镀。 29)Painting-喷漆。 30)Resin-胶材。 31)Printing-丝印。 32)Texturing-嗮纹/咬花。 33)Socket screw-带肩镙丝。 34)Inter lock/Straight lock-模锁。 35)Mold lock-运输块。 36)3plate mold-3板模。 37)Hot runner plate-热流道板。
电力电子-专业词汇中英文对照
电力电子-专业词汇中英文对照(一) AbsorberCircuit 吸收电路 AC/ACFrequencyConverter 交交变频电路ACpowercontrol交流电力控制ACPowerController交流调功电路ACPowerElectronicSwitch交流电力电子开关AcVoltageController交流调压电路AsynchronousModulation异步调制BakerClampingCircuit贝克箝位电路 Bi-directionalTriodeThyristor双向晶闸管BipolarJunctionTransistor--BJT双极结型晶体管Boost-BuckChopper升降压斩波电路Boost Chopper升压斩波电路BoostConverter升压变换器BridgeReversibleChopper桥式可逆斩波电路BuckChopper降压斩波电路BuckConverter降压变换器Commutation 换流 Conduction Angle 导通角ConstantVoltageConstantFrequency--CVCF 恒压恒频
ContinuousConduction--CCM (电流)连续模式ControlCircuit 控制电路 CukCircuit CUK斩波电路CurrentReversible Chopper 电流可逆斩波电路CurrentSourceTypeInverter--CSTI 电流(源)型逆变电路Cycloconvertor 周波变流器 DC-AC-DC Converter 直交直电路 DCChopping 直流斩波 DCChoppingCircuit 直流斩波电路 DC-DCConverter 直流-直流变换器DeviceCommutation 器件换流DirectCurrentControl 直接电流控制DiscontinuousConductionmode (电流)断续模式displacementfactor 位移因数 distortionpower 畸变功率 doubleendconverter 双端电路 drivingcircuit 驱动电路 electricalisolation 电气隔离 fastactingfuse 快速熔断器 fastrecoverydiode 快恢复二极管fastrevcoveryepitaxialdiodes 快恢复外延二极管
模具专业术语大全
模具专业术语大全
punch冲头 insert入块(嵌入 件)deburringpunch 压毛 边冲子groovepunch 压线冲子stampedpunch 字模冲子roundpunch 圆冲子 specialshapepunch 异形冲子bendingblock 折刀 roller滚轴 baffleplate 挡块 locatedblock 定位块supportingblockforlocatio n定位支承块 topplate上托板(顶板) topblock上垫脚 punchset上模座 punchpad上垫板 punchholder 上夹板 stripperpad 脱料背板 upstripper上脱料板 maledie公模(凸模) innerguidingpost 内导柱innerhexagonscrew 内六角螺钉dowelpin 固定销 coilspring弹簧 lifterpin顶料销 模具零件英语词汇 aircushionplate 气垫板 air-cushioneject-rod 气垫顶杆 trimmingpunch 切边冲子 stiffening ribpunch =stinger 加强筋冲子 reel-stretch punch 卷圆压平冲 子 guideplate 定位板 slidingblock 滑块 slidingdowelblock 滑块固定块 activeplate 活动板 lowerslidingplate 下滑块板 upperholderblock 上压块 模具模板英语词汇 featuredie 公母模 femaledie 母模(凹 模)upperplate 上 模板 lowerplate 下模板 diepad下垫板 dieholder 下夹板 dieset下模座 bottomblock 下垫脚 模具五金零件英语词汇eq- height sleeves=spool 等高 套筒 pin销 lifterguidepin 浮升导料销 guidepin导正销 uppermidplate 上中间板 springbox 弹簧箱 spring-boxeject-rod 弹簧箱顶杆 spring-boxeject-plate 弹簧箱顶板 bushingbolck 衬套 coverplate 盖板 guidepad 导料块 outerstripper 外脱料板 innerstripper 内脱料板 lowerstripper 下脱料板 ribbonpunch 压筋冲子 bottomplate 下托板(底 板)strippingplate 内 外打(脱料板)outerstripper 外脱料板 innerstripper内脱料板 lowerstripper下脱料板 coverplate盖板 wirespring 圆线弹簧 outerguidingpost 外导柱 stopscrew 止付螺丝 locatedpin 定位销 outerbush 外导套 模具冲压英语词汇 extensiondwg 展开图 proceduredwg 工程图 diestructuredwg 模具结构图 material材质 materialthickness 料片厚度 pressspecification 冲床 规格dieheightrange 适用模高 dieheight闭模高度 burr毛边 gap间隙 punchwt.上模重量 模具工程类英语词汇
专业英语词汇
电力电子专业英语 1、元件设备 三绕组变压器:three-column transformer ThrCln Trans 双绕组变压器:double-column transformer DblCl mnTrans 电容器:Capacitor 并联电容器:shunt capacitor 电抗器:Reactor 母线:Bus bar 输电线:Transmission Line 发电厂:power plant 断路器:Breaker 刀闸(隔离开关):Isolator
功角:power-angle 电压等级:voltage grade 空载损耗:no-load loss 铁损:iron loss 铜损:copper loss 空载电流:no-load current 阻抗:impedance 正序阻抗:positive sequence impedance 负序阻抗:negative sequence impedance 零序阻抗:zero sequence impedance 电阻:resistance 电抗:reactance 电导:conductance 电纳:susceptance 导纳:admittance
无功负载:reactive load 或者QLoad 有功负载: active load PLoad 遥测:YC(telemetering) 遥信:YX 励磁电流(转子电流):magnetizing current 定子:stator 功角:power-angle 上限:upper limit 下限:lower limit 并列的:apposable 高压: high voltage 低压:low voltage 中压:middle voltage 电力系统 power system 发电机 generator
模具专业术语大全
模具专业术语大全 punch冲头 insert入块(嵌入件)deburringpunch 压毛边冲子groovepunch 压线冲子stampedpunch 字模冲子roundpunch 圆冲子specialshapepunch 异形冲子bendingblock 折刀 roller滚轴 baffleplate 挡块 locatedblock 定位块supportingblockforlocation定位支 承块 topplate上托板(顶板) topblock上垫脚punchset上 模座punchpad上垫板 punchholder 上夹板 stripperpad 脱料背板 upstripper上脱料板maledie 公模(凸模) innerguidingpost 内导柱innerhexagonscrew 内六角螺钉dowelpin 固定销 coilspring弹簧lifterpin 顶料销 模具零件英语词汇 aircushionplate 气垫板 air-cushioneject-rod 气垫顶杆 trimmingpunch 切边冲子stiffening ribpunch =stinger 加强筋冲子 reel-stretch punch 卷圆压平冲 子 guideplate 定位板 slidingblock 滑块 slidingdowelblock 滑块固定块 activeplate 活动板 lowerslidingplate 下滑块板 upperholderblock 上压块 模具模板英语词汇 featuredie 公母模femaledie 母模(凹 模)upperplate 上模板 lowerplate 下模板 diepad下垫板dieholder 下夹板 dieset下模座 bottomblock 下垫脚 模具五金零件英语词汇 eq-height sleeves=spool 等高 套筒 pin销 lifterguidepin 浮升导料销 guidepin导正销 uppermidplate 上中间板 springbox 弹簧箱 spring-boxeject-rod 弹簧箱顶杆spring- boxeject-plate 弹簧箱顶板 bushingbolck 衬套 coverplate 盖板guidepad 导料块 outerstripper 外脱料板 innerstripper 内脱料板 lowerstripper 下脱料板 ribbonpunch 压筋冲子 bottomplate 下托板(底 板)strippingplate 内外打(脱料 板)outerstripper 外脱料板 innerstripper内脱料板 lowerstripper下脱料板 coverplate盖板 wirespring 圆线弹簧 outerguidingpost 外导柱stopscrew 止付螺丝 locatedpin 定位销 outerbush 外导套 模具冲压英语词汇 extensiondwg 展开图 proceduredwg 工程图 diestructuredwg 模具结构图 material材质 materialthickness 料片厚度 pressspecification 冲床规格 dieheightrange 适用模高 dieheight闭模高度 burr毛边 gap间隙 punchwt.上模重量 模具工程类英语词汇
工厂术语 英语
CORPORATE COMMON ABBREVIATION 常用语缩写 1 Organization组织 1-1 HQ Head Quarter 总公司 1-2Chairmen主席 1-3Lite-On Group光宝集团 1-4 President 总裁 1-5Executive Vice President 常务副总裁 1-6Vice President副总裁 1-7HR Human Resource人力资源部 1-8FIN Finance 财务 1-9Sales 销售 1-10R&D Research & Developing 研发部 1-11QA 质量保证QA DQA CS 1-12MIS Management Information System资讯管理系统1-13Pur 采购Purchasing 1-14IMD Image management division 影像管理事业部 1-15ITS information technology system 计算机部 1-16QRA quality reliability assurance 品保部 1-17MFG manufacturing 制造部 1-18PMC production &material control 生(产)物(料)管(理) 1-19 PRO Procuremnet 采购开发部
1-20 PMO Plant Manager Office 厂长室 1-21 CEO Chief Executive Officer 执行总裁 2 Materials 材料 2-1PC Production Control 生产控制 2-1-1MPS Mass Production Schedule 量产计划 2-1-2FGI Finished goods Inventory 成品存货 2-1-3UTS Units To Stock存货单元 2-1-4WIP Working In Process Inventory在制品 2-1-5C/T Cycle Time 循环时间,瓶颈 2-1-6WD Working Days 工作天 2-1-7MTD Month To Days 月初到今日(例如总表整理) 2-1-8YTD Year To Days 年初到今日 2-1-9 SO Sales Order 销售单 2-1-10MO Manufacture Order 制造单 2-1-11 BTO Build To Order 订单生产 2-1-12 P/N part number 料号 2-1-13 FCST Forecast 预测计划 2-1-14 W/O Working Order 工单 2-1-15 P/O Purchasing Order 采购单 2-1-16 VDS Vendor Delivery Schedule 厂商送货进度表2-1-17 D/C Delivery Order 交货单 2-2 MC Material Control材料控制
模具英语专业术语
模具英语专业术语模具的分类: 冲压模(五金模): stamping die 分离模: cutting die 成形模: forming die 塑胶模: plastics mold 注射模: injection mold 压缩模: compression mold 铸塑模: transfer mold 吹塑模: blow mold 吸塑模: suck mold 铸造模: casting die 砂型铸造: sand casting 压铸模: die casting 锻造模: forging die 塑胶模具术语 一、入水:gate 进入位(入水点):gate location 水口形式:gate type 大水口(侧浇口): edge gate 潜水口: sub-gate 薄膜式水口: film gate 牛角式潜水口: banana gate 扇形水口: fan gate 环形水口: ring gate 二次水口: 细水口:pin-point gate 水口大小:gate size 转水口:switching runner/gate 唧嘴口径:sprue diameter 直接水口: direct gate 二、流道: runner 热流道:hot runner,hot manifold 热嘴冷流道: hot sprue/cold runner 唧嘴直流: direct sprue gate 圆形(整圆/半圆)流道:round(full/half) runner 矩形流道: rectangle runner 梯形流道: trapezoid runner U形流道: U shape runner 流道电脑分析(模流分析):mold flow analysis 流道平衡: runner balance
电力系统_专业英语词汇
电力系统power system 发电机generator 励磁excitation 励磁器exciter电压voltage 电流current 升压变压器step-up transformer 母线bus 变压器transformer 空载损耗:no-load loss铁损:iron loss 铜损:copper loss 空载电流:no-load current无功损耗:reactive loss有功损耗:active loss 输电系统power transmission system 高压侧high side 输电线transmission line 高压: high voltage低压:low voltage 中压:middle voltage 功角稳定angle stability稳定stability 电压稳定voltage stability 暂态稳定transient stability 电厂power plant 能量输送power transfer 交流AC直流DC 电网power system 落点drop point 开关站switch station 调节regulation 高抗high voltage shunt reactor并列的:apposable 裕度margin 故障fault 三相故障three phase fault分接头:tap 切机generator triping 高顶值high limited value 静态static (state) 动态dynamic (state)自动电压调节器AVR Automatic voltage regulator 电抗reactance 电阻resistance 功角power angle 有功(功率)active power 电容器:Capacitor电抗器:Reactor 断路器:Breaker 电动机:motor 功率因数:power-factor 定子:stator 阻抗电压:阻抗:impedance功角:power-angle 电压等级:voltage grade 有功负载: active load/PLoad无功负载:reactive load档位:tap position 电阻:resistor电抗:reactance 电导:conductance 电纳:susceptance上限:upper limit 下限:lower limit 正序阻抗:positive sequence impedance负序阻抗:negative sequence impedance零序阻抗:zero sequence impedance 无功(功率)reactive power功率因数power factor 无功电流reactive current 斜率slope额定rating 变比ratio 参考值reference value电压互感器PT 分接头tap 仿真分析simulation analysis下降率droop rate 传递函数transfer function 框图block diagram受端receive-side 同步synchronization 保护断路器circuit breaker 摇摆swing 阻尼damping 无刷直流电机:Brushless DC motor 刀闸(隔离开关):Isolator机端generator terminal 变电站transformer substation 永磁同步电机:Permanent-magnet Synchronism Motor 异步电机:Asynchronous Motor 三绕组变压器:three-column transformer ThrClnTrans 双绕组变压器:double-column transformer DblClmnTrans 固定串联电容补偿fixed series capacitor compensation 双回同杆并架double-circuit lines on the same tower 单机无穷大系统one machine - infinity bus system 励磁电流:magnetizing current 补偿度degree of compensation Electromagnetic fields 电磁场失去同步loss of synchronization 装机容量installed capacity无功补偿reactive power compensation故障切除时间fault clearing time 极限切除时间critical clearing time 强行励磁reinforced excitation 并联电容器:shunt capacitor < 下降特性droop characteristics 线路补偿器LDC(line drop compensation) 电机学Electrical Machinery 自动控制理论Automatic Control Theory电磁场Electromagnetic Field微机原理Principle of Microcomputer 电工学Electrotechnics Principle of circuits 电路原理Electrical Machinery 电机学 电力系统稳态分析Steady-State Analysis of Power System 电力系统暂态分析Transient-State Analysis of Power System 电力系统继电保护原理Principle of Electrical System’s Relay Protection 电力系统元件保护原理Protection Principle of Power Syste m’s Element
模具英语专业术语
模具(MOULD/MOLD,TOOL): CAVITY:前模 CORE:后模(定模) DIMENSION:寸法 GATE:浇口/水口/入水口 PIN GATE:点水口/点浇入水 SIDE GATE:边水口/侧浇入水/大水口APPERANCE SURFACE:体裁面WARPAGE DIRECTION:变形方向 DRAFT ANGEL:脱模斜度 PARTING LINE/P。L:分模线 EJECT PIN/E。P:注塑顶针 BLAST/TEXTURE:喷啥,蚀纹 MIRROR FINISH:镜面(抛光)处理POLISH:抛光 EMD:放电加工 WELD:熔接加工(烧焊) LATHE:车床 MILLING CUTTER:铣刀 MILLING MACHINE:铣床 WIRE CUT:线切割 CNC:主加工中心 POWER DRILL:电钻 DRILLING:钻孔 FRITING:烧结 ANNEALING:淬火 注塑术语(INJECTION) SCREW:螺杆 WELD LINE:熔接线 SINK MARK:缩水 DRAG MARK:脱花 BURR:批锋 FLOW MARK:流纹 SHADOW MARK/GLOSS DIFFERENCE:光影SHORT:缺胶 INJECTION CYCLE:成型周期
注塑英语 型厚大小 Thick size 锁模结构(机绞/直压) Mode locking structure(machine twists/straight pressure) 最大开模距离 The biggest die sinking is away from 动模板最大模具重量 Moves the template maximum mold weight 哥林柱间距 Elder brother forest column spacing 顶出形式(电动五点,油压五点,油压十三点) Goes against the form (electrically operated five spots, flowing tubing head pressure five spots, flowing tubing head pressure 13 spots) 顶出长度 Goes against the length 顶棍孔直径 Goes against the stick hole diameter 顶棍孔中心矩 Goes against the stick hole central moment 螺杆材质(合金) Screw rod material quality (alloy) 螺杆转速 Screw rod rotational speed 最大射出体积 Projects the volume most greatly 最大射出量 Projects the quantity most greatly 射出率 Ejection rate 每10mm射出量(理论) Each 10mm projects the quantity (theory) 射咀直径 Shoots ju the diameter 射咀R值 Shoots ju the R value 射咀空径 Shoots ju the spatial diameter 定位环直径 Locating ring diameter 溶胶能力 Sol ability 驱动方式(全自动/全液压)
电气工程专业英语词汇汇总(综合版)
电气工程师专业英语词汇汇总 10kV distribution substation 10kV配电所abrupt change of voltage 电压突变accumulation of electric energy 电能存储actuating coil 动作线圈adjustment diagram 调整图 alarm 报警 alarm signal 报警信号alternating light 变光灯 ammeter 电流表 apparent energy consumption unit 单位视在能耗 arc furnace 电弧炉 armature 电枢 arrester; lighting arrester; surge diverters 避雷器 automatic voltage regulator 电压自动调整器backlighting; background illumination 背景照明 battery box 电池箱 battery charger 电池充电器battery contactor 电池接触器battery fuse 电池保险丝battery resistor 电池电阻器 blow-out coil 磁吹线圈 boom 吊杆 bracket (OCS) 底座(接触网); 支架;托架bracket for headspan wire 定位索底座bridge 电桥 brush 电刷 built-in wardrobe; built-in closet; closet 壁灯 bulb; light(lamp) bulb; electric bulb 灯泡 butterfly valve with electric actuator 电动蝶阀 button 电钮 cable and accessories 电缆及附件 cable armour 电缆铠装 cable bays 电缆电线间隔cable box 电缆箱 cable bracket; cable tray 电缆托架 cable continuity test 电路复测 cable differential protection 电缆差动保护
工厂专业英语术语
工厂专业英语术语 Assembly line组装线Layout布置图Conveyer流水线物料板Rivet table拉钉机Rivet gun拉钉枪Screw driver起子Pneumatic screw driver气动起子worktable 工作桌OO BA开箱检查fit together组装在一起fasten锁紧(螺丝) fixture 夹具(治具) pallet栈板b arcode条码barcode scanner条码扫描器fuse together熔合fuse machine热熔机repair修理operator作业员QC品管supervisor 课长ME制造工程师MT制造生技cos metic inspect外观检查inner parts inspect内部检查thumb screw大头螺丝lbs. inch 镑、英寸EMI gasket导电条 front plate前板rear plate后板chassis 基座bezel panel面板 power button电源按键reset button重置键Hi-pot test of SPS高源高压测试Voltage switch of SPS 电源电压接拉键sheet metal parts 冲件 plastic parts塑胶件SOP制造作业程序material check list物料检查表work cell工作间trolley台车carton纸箱sub-line支线left fork叉车personnel resource departmen t 人力资源部production department生产部门planning department企划部QC Secti on品管科 stamping factory冲压厂painting factory烤漆厂molding factory成型厂common e quipment常用设备uncoiler and straightener整平机 punching machine 冲床robot机械手hydraulic machine油压机 lathe车床planer |'plein?|刨床miller铣床grinder磨床 linear cutting线切割electrical sparkle电火花welder电焊机 staker=reviting machine铆合机position职务president董事长 general manager总经理special assistant manager特助 factory director厂长department director部长 deputy manager | =vice manager副理section supervisor课长 deputy section supervisor =vice section superisor副课长 group leader/supervisor组长line supervisor线长 assistant manager助理to move, to carry, to handle搬运 be put in storage入库pack packing包装to apply oil擦油 to file burr 锉毛刺final inspection终检to connect material接料 to reverse material 翻料wet station沾湿台Tiana天那水 cleaning cloth抹布to load material上料to unload material卸料 to return material/stock to退料scraped |'skr?pid|报废 scrape ..v.刮;削deficient purchase来料不良manufacture procedure制程deficient manufacturing procedure制程不良oxidation |' ksi'dei?n|氧化scratch刮伤dents压痕 defective upsiding down抽芽不良defective to staking铆合不良 embedded lump镶块feeding is not in place送料不到位 stamping-missing漏冲production capacity生产力 education and training教育与训练proposal improvement提案改善 spare parts=buffer备件forklift叉车trailer=long vehicle拖板车 compound die合模die locker锁模器pressure plate=plate pinch压板bolt螺栓administration/general affairs dept总务部automatic screwdriver电动启子thicknes s gauge厚薄规