Dimension Checking for US_Two pin 15A 125 V
欧洲各国2PIN电子元件插脚尺寸
2PIN欧洲插脚Two-pin plugs for class II appliances (Up to 2.5 A rating)According to EN50075 - Standard Sheet and IEC60083 - Standard C5A & P only for plug with supply cord. Direct plug-in product not consider the dimensions.UK Plug Checking Form according to Figure 4 of BS1363-3Grounding pinPosition Required (mm) By Measurement (mm)By the gauges in Figure A1A 6.35±0.15 -B 6.35±0.15C +0.150.051.63-- D 7.92 -- P E 10.31 -- P F 17.06±0.4 - G 19.94±0.8 1 21.9 max. or 27.0 min. - 2 21.9 max. or 27.0 min. - 3 21.9 max. or 27.0 min. - 4 21.9 max. or 27.0 min.- 5 60︒ -- P 6 60︒ -- P 7 8.6 min. - 8 21.0 max. 9 20.0±1.0 10 1.0 max 118.7±0.5Position Required (mm) By Measurement (mm) By the gauges in Figure A1 Plug type (h)R 0.35±0.05 -S 0.9±0.1 -T ≥0.60-V 6 -- PDimension Checking for Two-pin plugs of NA (15 A, 125 V) According to (NEMA WD 6-2002 Figure 1-15)Dimension Checking for Tow-pin plugs (6 A, 10 A rating) According to Fig 1 of GB 1002-2008dDimension Checking for Korea plugs (Two-pole plug for 3A250V) According to KSC 8305日本插脚巴西插脚Equipment’s combined with two-pole plug (Class II) 10 A/250V a.c. (figure 13. NBR 14136: 2002)Note:1 The sketches are not intended to govern design, except as regards the dimensions shown2 Plugs can be rewirable or non-rewirableRequirements:①– The distance between the engagement face and the cord or cord guard, if any, shall be at least 14 mm②– Within this distance, the outline shall be not smaller than the engagement face.③– Within this distance, the outline shall be not larger than the engagement face.④– Insulating sleeves on the current-carrying pins are optional If the insulating sleeves are separate parts, they shall enter the plug by at least 3mm measured from the engagement face.⑤– The external diameter of the insulating sleeves shall not be larger than the diameter of the uninsulated part of the pins.⑥– To avoid damage to shutters, the ends of the pins shall show neither sharp edges nor burrs. They shall印度插脚：Indian Plug Checking WorksheetDimension: mmNote:1. “G” is the minimum distance between the pins and the periphery of the plug.IRAM 2063 Plug (Class II, two-pole) Checking Worksheet（IRAM 2063：1982 + Amd 1999）SASO Plug Checking Form according to Figure 1 of SASO 2203。
BU_61580寄存器说明中文版
1 SOFTWARE INTERFACE 软件接口 ....................................................................................................................... 1 1.1. POWER TURN-ON/INITIALIZATION STATE 上电/初始化状态 .................................................................... 1 1.2. OVERALL ADDRESS MAPPING: WORDS VS. BYTES 整体地址映射：字 和 位 ........................................ 2 1.3. SOFTWARE INTERFACE: INTERNAL RAM 软件接口：内部 RAM .............................................................. 3 1.4. INTERNAL REGISTERS ADDRESS AND BIT MAPPING 内部寄存器地址和位映射 ..................................... 3 1.5. INTERRUPT MASK REGISTER 中断屏蔽寄存器 ........................................................................................ 6 1.5.1. RAM PARITY ERROR RAM 校验错误...........................................................
检具规范-Standard Specification for Checking fixture(Design)_140331_English
Checking FixtureStandard Specification Document (Design)CONTENTSIntroduction1. Contents of arrangements2. About checking fixture structure2.1. About checking fixture of ONLY, checking fixture of ASSY, PCF and plug gauge 2.2. About checking fixture of ONLY, Checking fixture of ASSY and PCF2.3. About plug gauge3. About paint (direct on a drawing)Standard design specification1.Contents of arrangements1.1.This construction is arranged as design commission (Transfer the copyright of a drawing to Mazda).※Design commission is design ~ numerical value reading (Data creation in which NC processing is possible).1.2.In a design, do compilation design about design data and drawing of former vehicle type as much as possible.※In a new order, Mazda offers the group figure and part drawing of the former vehicle type as reference at the time of order.1.3.Design need to be created 3D design (It is necessary to also create 2D drawing). Let the offerdocuments to Mazda be the following point.1.4.The following shows the delivery point of the drawing data.○Divide 3D data according to the data of base, framework, datum part, and gauge part.○When sharing vehicle type and model, divide 3D data (model, processing side) into common part and exclusive part.○Submit data by optical media (CD, DVD).1.5.Submit a middle figure when design is completed to the grade which the whole checking fixturestructure can be understand.※The basic flow: design start ~ middle figure check ~ last delivery of materials.※Submit the middle figure by 3D model data (Form is iges or jt).1.6.In all presentation drawing and number table, English must be also shown.e the symbol defined by ISO in the drawing.1.8.About the data used for the design, we provide the data of a suitable ECN number which is at theorder time.1.9. Standard parts that numbered all part numbers, write the dimensions included in the drawing.1.10.Show operation manual.1.11.Scale of dimension is mm (millimeter).1.12.Drawing must be drawn by third angle projection.1.13.Drawing is the method of unit drawing.(total assembly drawing, base processing drawing, base slotted drawing, unit assembly drawing, dismounted parts drawing）1.14.About clamp and other purchase etc. , use MISUMI products.1.15.Size of drawing is not greater than A2.Size of print is not greater than A3.1.16.Amount of every space must be shown in drawing, including 0-space and 3-space.1.17.Nominal position, measured result position and error of measurement point must be shown in K2point table.1.18.Deviation tolerance setup point is only datum part. Show the deviation information of datum part. 1.19.Write the material used to cross-sectional view1.20.Write the welds and adhesion place to drawing view.2.About checking fixture structure2.1.About checking fixture of ONLY, checking fixture of ASSY, PCF and plug gauge2.1.1.Material quality of processing datum hole is SS. In the case of AL or resin, set up a bush.2.1.2.Datum pin, scibe pin, and scibe piece must be carried out quenching treatment.2.1.3.Material quality of processing datum level is SS. In the case of AL or resin, set up a shim.※Setting up fixation (screw stop) of Shim must be outside datum surface fundamentally.2.1.4.Set up a bush, when principal part of check hole is resin.※In SS and AL, bush is unnecessary.2.1.5.Gauge width of the part measured with level difference gauge (dial gauge) should be secured over25mm.※Unite the principal part setting direction with the flow in form.※Take into consideration the position of a hand and the condition of viewing when a leveldifference gauge is carried.2.1.6.Secure a stop of the principal part from a measurement point over 5mm.2.1.7.When there is a replacement gauge, set up the space for it.※When a setup of a storage place is difficult, storage is separately determined in a previousarrangement.2.1.8.Design in consideration of work's self weight and checking fixture's self weight.※Datum and measured region is permitted to sag 0.1mm or less under empty weight at thetime of setting checking fixture of attachment datum.2.1.9.Cut PT principal part in a less than 300mm pitch. (In order to lose expansion of the material bychange of temperature)※Indicate on a drawing.2.1.10.Structure of checking fixture must be maintainable about degree of accuracy.2.1.11.When you extend clamp arm, the portion of joint must be welded.e bolt with a rubber fundamentally about clamp head.2.1.1e ensat bush about tap hole AL and PT etc.2.1.14.Removable and replaceable gauge must be able to be bolt up in empty space in base.2.1.15.PT hardness must not be less 80 and linear expansion coefficient not greater than0.03.※Use metal corresponding to the above condition if it is difficult to obtain such PT.2.1.16.Movable gauge is abutment surface type.e pin with internal thread when you use positioning dowel pin for fixed gauge and movablegauge.e socket bolt with spring washer and flat washer for tightening up fixed gauge.※It must be plated material (antirust).e wing screw for clamping movable gauge.※Adhere flat washer with wing screw.2.1.20.CK and SK is adjustable. Setup clamp except special mention.2.2.About checking fixture of ONLY, Checking fixture of ASSY and PCF2.2.1.Positioning of holder (angle plate) is dowel pin type of abutment surface type.2.2.2.Set up a bush, when principal part of check hole is resin.※Depth of check pin insertion part hole about Φ2, Φ3, and Φ5 is fundamentally 20mm(Penetration is impossible).2.2.3. Section gauge is made SS or AL, and plate thickness is about 3.2 ~ 10mm.※When there are many amounts of running out, reinforce with angle bar or decenter impellertype.2.2.4.About clamp, toggle clamp is used fundamentally.※Depending on a part, Using pin clamp or C type clamp is possible.2.2.5.Arrange clamp not to come right above measurement point.※Separate from measurement part 50mm or more.2.2.6.Secure a stop of the principal part from the measurement point over 5mm.2.2.7.Keep gauge etc. from overflowing from base surface.※When it overflow, take safety measures with stopper/safety bar, and color in yellow.2.2.8. The forklift guide is not set.※If necessary for safety, it is indicated in the each part's specifications.2.3.About plug gauge2.3.1.The body used for plug gauge measurement is not made with nominal value 0.At the time of datum set clamp, when a datum is a fault restraint, excessive stress may be applied to rib or frame of a plug gauge.So even if there is poor body accuracy between about ±5-mm datum and cyclic stress is applied, there should be neither irreversible plastic deformation nor fracture.2.3.2.Datum gauge must be used SS material for interference evasion with body.(Example: The datum gauge under the bonnet of head lamp plug gauge, the datum gauge under the lift gate of R bumper plug gauge)※In the above, main part hold part of SS material datum gauge must give the rigidity supporting the load of the plug gauge.2.3.3.Position and fix by 2 knocks so that the hold part of main part of datum gauge does not shift.2.3.4.Secure the set plate of a holder about 15~20mm.2.3.5.Even if you use it for five years, make it structure which does not have exfoliation by aging.2.3.6.Datum gauge must be put by the holder side or fixed by 2 knocks.2.3.7.Free scale of datum hole should be over ±min2~max3mm.2.3.8.Chase cross-shaped into the back of grip of clamp datum pin, bolt, and nut.2.3.9.Datum gauge is kept from being bent by about 5kg of load (holder structure is also included).2.3.10.Attach taper on the tip of a datum pin for guide (3~5mm in taper length and 15 degrees of taperangle).2.3.11.Projection between datum pin and work in guide part is about 3~5mm.2.3.12.About direction regulation of the diagram pin, regulate by method of a horizontal stop tap etc.which can be adjusted.2.3.13.Attach scibe needle for exclusive use to the measured region which needs CL or straight scibe. 2.3.14.Secure a stop of the principal part from marked line point over 5mm.2.3.15.Plug gauge is used in the state of real vehicle, and no interference body and adjoining plug gauge.(Be careful ofopening and closing of lid thing parts)※Adjoining plug gauge is range of set order.3.About paint (direct on a drawing)3.1 paint it for prevention of rust in a non-precision side of iron.I order the painting color separately.Even antirust treatment except the painting is possibleExample) plating, black dyeing3.2.Paint the circumference with red, such as H, h, S, and s, in red (Do not paint to the clamp bar side).3.3. When deliver it, rust do not be generated.。
电子信息工程专业英语词汇(精华整理版)
电子信息工程专业英语词汇(精华整理版)编辑整理：尊敬的读者朋友们：这里是精品文档编辑中心，本文档内容是由我和我的同事精心编辑整理后发布的，发布之前我们对文中内容进行仔细校对，但是难免会有疏漏的地方，但是任然希望（电子信息工程专业英语词汇(精华整理版)）的内容能够给您的工作和学习带来便利。
同时也真诚的希望收到您的建议和反馈，这将是我们进步的源泉，前进的动力。
本文可编辑可修改，如果觉得对您有帮助请收藏以便随时查阅，最后祝您生活愉快业绩进步，以下为电子信息工程专业英语词汇(精华整理版)的全部内容。
transistor n 晶体管diode n 二极管semiconductor n 半导体resistor n 电阻器capacitor n 电容器alternating adj 交互的amplifier n 扩音器，放大器integrated circuit 集成电路linear time invariant systems线性时不变系统voltage n 电压，伏特数tolerance n 公差；宽容；容忍condenser n 电容器；冷凝器dielectric n 绝缘体；电解质electromagnetic adj 电磁的adj 非传导性的deflection n偏斜；偏转；偏差linear device 线性器件the insulation resistance 绝缘电阻anode n 阳极,正极cathode n 阴极breakdown n 故障;崩溃terminal n 终点站；终端，接线端emitter n 发射器collect v 收集，集聚，集中insulator n 绝缘体，绝热器oscilloscope n 示波镜；示波器gain n 增益,放大倍数forward biased 正向偏置reverse biased 反向偏置P-N junction PN结MOS（metal-oxide semiconductor）金属氧化物半导体enhancement and exhausted 增强型和耗尽型integrated circuits 集成电路analog n 模拟digital adj 数字的，数位的horizontal adj, 水平的，地平线的vertical adj 垂直的，顶点的amplitude n 振幅，广阔,丰富attenuation n衰减；变薄;稀薄化multimeter n 万用表frequency n 频率，周率the cathode-ray tube 阴极射线管dual—trace oscilloscope 双踪示波器signal generating device 信号发生器peak-to—peak output voltage 输出电压峰峰值sine wave 正弦波triangle wave 三角波square wave 方波amplifier 放大器，扩音器oscillator n 振荡器feedback n 反馈,回应phase n 相，阶段，状态filter n 滤波器，过滤器rectifier n整流器；纠正者band-stop filter 带阻滤波器band-pass filter 带通滤波器decimal adj 十进制的，小数的hexadecimal adj/n十六进制的binary adj 二进制的；二元的octal adj 八进制的domain n 域；领域code n代码,密码,编码v编码the Fourier transform 傅里叶变换Fast Fourier Transform 快速傅里叶变换microcontroller n 微处理器；微控制器assembly language instrucionsn 汇编语言指令chip n 芯片，碎片modular adj 模块化的；模数的sensor n 传感器plug vt堵，塞，插上n塞子，插头，插销coaxial adj 同轴的，共轴的fiber n 光纤relay contact 继电接触器single instruction programmer单指令编程器dedicated manufacturesprogramming unit 专供制造厂用的编程单元beam n （光线的）束,柱，梁polarize v（使）偏振，（使）极化Cathode Ray Tube（CRT）阴极射线管neuron n神经元;神经细胞fuzzy adj 模糊的Artificial Intelligence Shell人工智能外壳程序Expert Systems 专家系统Artificial Intelligence 人工智能Perceptive Systems 感知系统neural network 神经网络fuzzy logic 模糊逻辑intelligent agent 智能代理electromagnetic adj 电磁的coaxial adj 同轴的，共轴的microwave n 微波charge v充电，使充电insulator n 绝缘体，绝缘物nonconductive adj非导体的，绝缘的antenna n天线;触角modeling n建模，造型simulation n 仿真；模拟prototype n 原型array n 排队，编队vector n 向量，矢量wavelet n 微波，小浪sine 正弦 cosine 余弦inverse adj倒转的,反转的n反面；相反v倒转high—performance 高精确性，高性能two—dimensional 二维的；缺乏深度的three—dimensional 三维的；立体的；真实的object—oriented programming面向对象的程序设计spectral adj 光谱的attenuation n衰减;变薄；稀释distortion n 失真，扭曲,变形wavelength n 波长refractive adj 折射的ATM 异步传输模式AsynchronousTransfer ModeADSL非对称用户数字线Asymmetricdigital subscriber lineVDSL甚高速数字用户线very highdata rate digital subscriberlineHDSL高速数据用户线 high ratedigital subscriber lineFDMA频分多址（Frequency DivisionMultiple Access）TDMA时分多址(Time DivisionMultiple Access）CDMA同步码分多址方式(CodeDivision Multiple Access)WCDMA宽带码分多址移动通信系统（Wideband Code DivisionMultiple Access)TD—SCDMA（Time DivisionSynchronous Code DivisionMultiple Access）时分同步码分多址SDLC(synchronous data linkcontrol）同步数据链路控制HDLC(high—level data linkcontrol)高级数据链路控制IP/TCP（internet protocol/transfer Control Protocol）网络传输控制协议ITU (InternationalTelecommunication Union)国际电信联盟ISO国际标准化组织（InternationalStandardization Organization）;OSI开放式系统互联参考模型(OpenSystem Interconnect）GSM全球移动通信系统（GlobalSystem for Mobile Communications)GPRS通用分组无线业务（GeneralPacket Radio Service)FDD(frequency division duplex）频分双工TDD(time division duplex)时分双工VPI虚路径标识符（Virtual PathIdentifier）；ISDN（Integrated ServicesDigital Network）综合业务数字网IDN综合数字网（integrateddigital network）HDTV （high definitiontelevision)高清晰度电视DCT（Discrete Cosine Transform）离散余弦变换VCI(virtual circuit address）虚通路标识MAN城域网Metropolitan areanetworksLAN局域网local area networkWAN广域网wide area network同步时分复用STDM SynchronousTime Division Multiplexing统计时分复用STDM StatisticalTime Division Multiplexing单工传输simplex transmission半双工传输half-duplex transmission全双工传输full-duplex transmission交换矩阵Switching Matrix电路交换 circuit switching分组交换packet switching报文交换message switching奇偶校验parity checking循环冗余校验CRC Cyclic Redundancy Check虚过滤Virtual filter数字滤波digital filtering伪随机比特Quasi Random Bit带宽分配 Bandwidth allocation信源information source信宿destination数字化digitalize数字传输技术Digital transmission technology灰度图像Grey scale images灰度级Grey scale level幅度谱Magnitude spectrum相位谱Phase spectrum频谱frequency spectrum智能设备Smart Device软切换Soft handover硬切换 Hard Handover相干检测Coherent detection边缘检测Edge detection冲突检测collision detection业务集合service integration业务分离/综合service separation/ integration网络集合network integration环形网Ring networks令牌环网Token Ring network网络终端Network Terminal用户终端user terminal用户电路line circuit电路利用率channel utilization （通道利用率）相关性coherence相干解调coherent demodulation数字图像压缩digital image compression图像编码image encoding有损/无损压缩lossy/lossless compression解压decompression呼叫控制Call Control误差控制error control存储程序控制stored program control存储转发方式store-and-forward manner语音\视频传输voice\video transmission视频点播video—on-demand（VOD)会议电视Video Conference有线电视cable television量化quantization吞吐量throughput话务量traffic多径分集Multipath diversity多媒体通信MDM Multimedia Communication多址干扰Multiple Access Interference人机交互man machine interface 交互式会话Conversationalinteraction路由算法Routing Algorithm目标识别Object recognition话音变换Voice transform中继线trunk line传输时延transmission delay远程监控remote monitoring光链路optical link拓扑结构Topology均方根root mean squarewhatsoever=whatever 0switchboard （电话）交换台bipolar （电子）双极的premise （复）房屋，前提cursor （计算机尺的）游标,指导的elapse （时间）经过，消失vaporize (使)蒸发subsystem （系统的）分部,子系统,辅助系统metallic (像）金属的，含金属的，（声音)刺耳的dispatch (迅速）派遣，急件consensus （意见)一致,同意deadline (最后）期限，截止时间tomographic X线体层摄像的alas 唉，哎呀cluster把…集成一束，一组，一簇，一串，一群encyclopedia 百科全书millionfold 百万倍的semiconductor 半导体radius 半径范围,半径，径向射线half-duplex transmission 半双工传输accompaniment 伴随物，附属物reservation 保留，预定quotation 报价单，行情报告,引语memorandum 备忘录redundancy 备用be viewed as 被看作…be regards as 被认为是as such 本身;照此;以这种资格textual 本文的，正文的verge 边界variation 变化，变量conversion 变化，转化identity 标识；标志criterion 标准，准则in parallel on 并联到,合并到juxtapose 并置，并列dialing pulse 拨号脉冲wave-guide 波导wavelength division multiplexed波分复用baud rate 波特率playback 播放（录音带，唱片)no greater than 不大于update不断改进,使…适合新的要求，更新asymmetric 不对称的irrespective 不考虑的，不顾的inevitably 不可避免的inevitable 不可避免的，不可逃避的，必定的segment 部分abrasion 擦伤,磨损deploy 采用，利用,推广应用take the form of 采用…的形式parameter 参数，参量layer 层dope 掺杂FET（field effect transistors) 场效应管audio recording 唱片ultra—high—frequency(UHF）超高频in excess of 超过in excess of 超过hypertext 超文本ingredient 成分,因素ingredient 成分，组成部分，要素metropolitan—area network（WAN）城域网metropolitan area network（WAN)城域网，城市网络congestion 充满，拥挤，阻塞collision 冲突extractive 抽出；释放出extract 抽取，取出，分离lease 出租,租约，租界期限，租界物pass on 传递，切换transmission 传输facsimile 传真innovative=innovatory 创新的，富有革新精神的track 磁道impetus 促进,激励cluster 簇stored-program control(SPC）存储程序控制a large number of 大量的peal 大声响，发出supersede 代替supplant 代替，取代out—of—band signaling 带外信号simplex transmission 单工传输monochromatic 单色的，单色光的，黑白的ballistic 弹道的，射击的，冲击的conductor 导体hierarchy 等级制度，层次infrastructure 底层结构，基础结构geographic 地理的,地区的geographically 地理上GIS（ground instrumentationsystem) 地面测量系统ground station 地面站earth orbit 地球轨道extraterrestrial 地球外的，地球大气圈外的Land-sat 地球资源卫星rug 地毯，毯子ignite 点火,点燃，使兴奋electromagnetic 电磁的inductive 电感arc 电弧telephony 电话（学)，通话dielectric 电介质，绝缘材料；电解质的，绝缘的capacitor 电容telecommunication 电信，无线电通讯scenario 电影剧本，方案modem pool 调制解调器（存储）池superimposing 叠加，重叠pin 钉住，扣住，抓住customize 定做，定制monolithic 独立的，完全统一的aluminize 镀铝strategic 对全局有重要意义的，战略的substantial 多的，大的，实际上的multi-path fading 多径衰落multi—path 多路，多途径；多路的,多途径的multi-access 多路存取，多路进入multiplex 多路复用multiplex 多路复用的degradation 恶化，降级dioxide 二氧化碳LED(light—emitting—diode）发光二极管evolution 发展,展开，渐进feedback 反馈，回授dimension 范围，方向，维,元scenario 方案scenario 方案，电影剧本amplifer 放大器noninvasive 非侵略的，非侵害的tariff 费率，关税率；对…征税distributed functional plane(DFP）分布功能平面DQDB(distributed queue dual bus)分布式队列双总线hierarchy 分层，层次partition 分成segmentation 分割interface 分界面，接口asunder 分开地，分离地detached 分离的,分开的,孤立的dispense 分配allocate 分配，配给;配给物centigrade 分为百度的,百分度的，摄氏温度的fractal 分形molecule 分子，微小，些微cellular 蜂窝状的cellular 蜂窝状的,格形的，多孔的auxiliary storage（also called secondary storage) 辅助存储器decay 腐烂，衰减，衰退negative 负电vicinity 附近，邻近vicinity 附近地区,近处sophisticated 复杂的，高级的，现代化的high-frequency(HF) 高频high definition television 高清晰度电视chromium 铬annotate 给…作注解in terms of 根据,按照disclosure 公布,企业决算公开public network 公用网functionality 功能，功能度mercury 汞resonator 共鸣器resonance 共振whimsical 古怪的，反复无常的administration 管理，经营cursor 光标（显示器），游标，指针optical computer 光计算机photoconductor 光敏电阻optical disks 光盘optically 光学地，光地wide—area networks 广域网specification 规范,说明书silicon 硅the internationaltelecommunication union（ITU) 国际电信联盟excess 过剩obsolete 过时的，废弃的maritime 海事的synthetic 合成的，人造的，综合的synthetic 合成的，综合性的rational 合乎理性的rationalization 合理化streamline 合理化，理顺infrared 红外线的，红外线skepticism 怀疑论ring network 环形网hybrid 混合物counterpart 伙伴，副本，对应物electromechanical 机电的，电动机械的Robot 机器人Robotics 机器人技术，机器人学accumulation 积累infrastructure 基础，基础结构substrate 基质,底质upheaval 激变,剧变compact disc 激光磁盘(CD）concentrator 集中器，集线器centrex system 集中式用户交换功能系统converge on 集中于，聚集在…上lumped element 集总元件CAI(computer-aided instruction)计算机辅助教学computer—integratedmanufacturing（CIM）计算机集成制造computer mediated communication（CMC）计算机中介通信record 记录register 记录器，寄存器expedite 加快,促进weight 加权accelerate 加速，加快，促进categorize 加以类别，分类in addition 加之，又，另外hypothetical 假设的rigidly 坚硬的，僵硬的compatibility 兼容性，相容性surveillance 监视surveillance 监视retrieval 检索,（可）补救verification 检验simplicity 简单，简明film 胶片,薄膜take over 接管，接任ruggedness 结实threshold 界限，临界值with the aid of 借助于，用，通过wire line 金属线路,有线线路coherent 紧凑的，表达清楚的，粘附的,相干的compact 紧密的approximation 近似undertake 进行，从事transistor 晶体管elaborate 精心制作的，细心完成的，周密安排的vigilant 警戒的，警惕的alcohol 酒精,酒local area networks（LANs）局域网local-area networks(LANs）局域网drama 剧本,戏剧，戏剧的演出focus on 聚集在,集中于,注视insulator 绝缘root mean square 均方根uniform 均匀的open—system-interconnection(OSI）开放系统互连expire 开始无效，满期，终止immunity 抗扰，免除，免疫性take…into account考虑，重视…programmable industrialautomation 可编程工业自动化demountable 可拆卸的tunable 可调的reliable 可靠be likely to 可能，大约，像要videotex video 可视图文电视negligible 可以忽略的aerial 空气的，空中的,无形的,虚幻的；天线broadband 宽（频）带pervasive 扩大的，渗透的tensile 拉力的，张力的romanticism 浪漫精神，浪漫主义discrete 离散,不连续ion 离子force 力量；力stereophonic 立体声的continuum 连续统一体，连续统，闭联集smart 灵巧的；精明的；洒脱的token 令牌on the other hand 另一方面hexagonal 六边形的，六角形的hexagon 六角形，六边形monopoly 垄断，专利video-clip 录像剪辑aluminum 铝pebble 卵石，水晶透镜forum 论坛，讨论会logical relationships 逻辑关系code book 码本pulse code modulation(PCM）脉冲编码调制roam 漫步,漫游bps(bits per second) 每秒钟传输的比特ZIP codes 美国邮区划分的五位编码susceptible(to）敏感的，易受…的analog 模拟，模拟量pattern recognition 模式识别bibliographic 目录的,文献的neodymium 钕the european telecommunicationstandardization institute(ETSI)欧洲电信标准局coordinate 配合的，协调的;使配合，调整ratify 批准,认可bias 偏差；偏置deviate 偏离，与…不同spectrum 频谱come into play 其作用entrepreneurial 企业的heuristic methods 启发式方法play a …role(part)起…作用stem from 起源于；由…发生organic 器官的，有机的,组织的hypothesis 前提front-end 前置，前级potential 潜势的，潜力的intensity 强度coincidence 巧合，吻合，一致scalpel 轻便小刀，解剖刀inventory 清单,报表spherical 球的,球形的distinguish 区别，辨别succumb 屈服，屈从，死global functional plane（GFP) 全局功能平面full-duplex transmission 全双工传输hologram 全息照相，全息图deficiency 缺乏thermonuclear 热核的artifact 人工制品AI(artificial intelligence) 人工智能fusion 熔解，熔化diskettes（also called floppy disk) 软盘sector 扇区entropy 熵uplink 上行链路arsenic 砷neural network 神经网络very-high—frequency(VHF) 甚高频upgrade 升级distortion 失真，畸变identification 识别，鉴定，验明pragmatic 实际的implementation 实施,实现，执行，敷设entity 实体，存在vector quantification 矢量量化mislead 使…误解,给…错误印象，引错vex 使烦恼，使恼火defy 使落空facilitate 使容易，促进retina 视网膜compatible 适合的，兼容的transceiver 收发两用机authorize 授权，委托,允许data security 数据安全性data independence 数据独立data management 数据管理database 数据库database management system(DBMS）数据库管理信息系统database transaction 数据库事务data integrity 数据完整性,数据一致性attenuation 衰减fading 衰落，衰减，消失dual 双的，二重的transient 瞬时的deterministic 宿命的，确定的algorithm 算法dissipation 损耗carbon 碳diabetes 糖尿病cumbersome 讨厌的，麻烦的,笨重的razor 剃刀，剃go by the name of 通称,普通叫做commucation session 通信会话traffic 通信业务(量）synchronous transmission 同步传输concurrent 同时发生的,共存的simultaneous 同时发生的，同时做的simultaneous 同时发生的，一齐的coaxial 同轴的copper 铜statistical 统计的，统计学的dominate 统治，支配invest in 投资perspective 透视，角度，远景graphics 图示，图解pictorial 图像的coating 涂层,层deduce 推理reasoning strategies 推理策略inference engine 推理机topology 拓扑结构heterodyne 外差法的peripheral 外界的，外部的，周围的gateway 网关hazardous 危险的microwave 微波（的）microprocessor 微处理机，微处理器microelectronic 微电子nuance 微小的差别（色彩等）encompass 围绕，包围，造成，设法做到maintenance 维护;保持；维修satellite communication 卫星通信satellite network 卫星网络transceiver 无线电收发信机radio—relay transmission 无线电中继传输without any doubt 无疑passive satellite 无源卫星sparse 稀少的，稀疏的downlink 下行链路precursor 先驱，前任visualization 显像feasibility 现实性,可行性linearity 线性度constrain 限制,约束，制约considerable 相当的,重要的geo-stationary 相对地面静止by contrast 相反，而,对比起来coorelation 相关性mutual 相互的mutually 相互的，共同的interconnect 相互连接,互连one after the other 相继，依次minicomputer 小型计算机protocol 协议，草案protocol 协议，规约,规程psycho-acoustic 心理（精神）听觉的;传音的channelization 信道化，通信信道选择run length encoding 行程编码groom 修饰，准备virtual ISDN 虚拟ISDNmultitude 许多，大批,大量whirl 旋转preference 选择，喜欢avalanche 雪崩pursue 寻求，从事interrogation 询问dumb 哑的，不说话的，无声的subcategory 亚类，子种类，子范畴orbital 眼眶；轨道oxygen 氧气,氧元素service switching and controlpoints(SSCPs）业务交换控制点service control points(SCPs) 业务控制点service control function（SCF) 业务控制功能in concert 一致，一齐handover 移交，越区切换at a rate of 以……的速率in the form of 以…的形式base on… 以…为基础yttrium 钇(稀有金属,符号Y）asynchronous transmission 异步传输asynchronous 异步的exceptional 异常的，特殊的voice—grade 音频级indium 铟give rise to 引起,使产生cryptic 隐义的,秘密的hard disk 硬盘hard automation 硬自动化by means of 用，依靠equip with 用…装备subscriber 用户telex 用户电报PBX（private branch exchange）用户小交换机或专用交换机be called upon to 用来…，（被）要求…superiority 优势predominance 优势，显著active satellite 有源卫星in comparison with 与…比较comparable to 与…可比preliminary 预备的，初步的premonition 预感,预兆nucleus 原子核valence 原子价circumference 圆周，周围teleprocessing 远程信息处理，遥控处理perspective 远景，前途constrain 约束，强迫mobile 运动的，流动的，机动的，装在车上的convey 运输，传递,转换impurity 杂质impurity 杂质,混杂物，不洁，不纯regenerative 再生的improve over 在……基础上改善play important role in 在…中起重要作用in close proximity 在附近，在很近underlying 在下的，基础的in this respect 在这方面entail 遭遇，导致presentation 赠与，图像,呈现，演示narrowband 窄（频)带deploy 展开，使用，推广应用megabit 兆比特germanium 锗positive 正电quadrature 正交orthogonal 正交的quadrature amplitudemodulation(QAM) 正交幅度调制on the right track 正在轨道上sustain 支撑，撑住，维持，持续outgrowh 支派；长出；副产品dominate 支配，统治knowledge representation 知识表示knowledge engineering 知识工程knowledge base 知识库in diameter 直径helicopter 直升飞机acronym 只取首字母的缩写词as long as 只要，如果tutorial 指导教师的，指导的coin 制造（新字符），杜撰fabrication 制造，装配；捏造事实proton 质子intelligence 智能,智力，信息intelligent network 智能网intermediate 中间的nucleus(pl.nuclei) 中心，核心neutrons 中子terminal 终端，终端设备overlay 重叠，覆盖，涂覆highlight 重要的部分，焦点charge 主管，看管;承载dominant 主要的,控制的，最有力的cylinder 柱面expert system 专家系统private network 专用网络transition 转变，转换,跃迁relay 转播relay 转播，中继repeater 转发器,中继器pursue 追赶,追踪，追求，继续desktop publish 桌面出版ultraviolet 紫外线的，紫外的；紫外线辐射field 字段vendor 自动售货机，厂商naturally 自然的；天生具备的synthesize 综合,合成integrate 综合，使完全ISDN(intergrated servicesdigital network) 综合业务数字网as a whole 总体上bus network 总线形网crossbar 纵横，交叉impedance 阻抗initial 最初的，开始的optimum 最佳条件appear as 作为…出现A Analog 模拟A/D Analog to Digital 模—数转换AAC Advanced Audio Coding高级音频编码ABB Automatic Black Balance 自动黑平衡ABC American Broadcasting Company 美国广播公司Automatic Bass Compensation 自动低音补偿 Automatic BrightnessControl 自动亮度控制ABL Automatic Black Level自动黑电平ABLC Automatic BrightnessLimiter Circuit 自动亮度限制电路ABU Asian BroadcastingUnion 亚洲广播联盟(亚广联ABS American Bureau ofStandard 美国标准局AC Access Conditions 接入条件Audio Center 音频中心ACA Adjacent ChannelAttenuation 邻频道衰减ACC Automatic CenteringControl 自动中心控制Automatic Chroma Control 自动色度(增益ACK Automatic Chroma Killer自动消色器ACP Additive Colour Process加色法ACS Access Control System接入控制系统Advanced CommunicationService 高级通信业务Area Communication System区域通信系统ADC Analog to DigitalConverter 模-数转换器Automatic DegaussirngCircuit 自动消磁电路ADL Acoustic Delay Line 声延迟线ADS Audio DistributionSystem 音频分配系统AE Audio Erasing 音频（声音AEF Automatic EditingFunction 自动编辑功能AES Audio EngineeringSociety 音频工程协会AF Audio Frequency 音频AFA Audio FrequencyAmplifier 音频放大器AFC Automatic FrequencyCoder 音频编码器Automatic Frequency Control自动频率控制AFT Automatic Fine Tuning自动微调Automatic Frequency Track自动频率跟踪Automatic Frequency Trim 自动额率微调AGC Automatic Gain Control自动增益控制AI Artificial Intelligence人工智能ALM Audio—Level Meter 音频电平表AM Amplitude Modulation 调幅AMS Automatic Music Sensor自动音乐传感装置ANC Automatic NoiseCanceller 自动噪声消除器ANT ANTenna 天线AO Analog Output 模拟输出APS Automatic ProgramSearch 自动节目搜索APPS Automatic ProgramPause System 自动节目暂停系统APSS Automatic ProgramSearch System 自动节目搜索系统AR Audio Response 音频响应ARC Automatic RemoteControl 自动遥控ASCII American StandardCode for InformationInterchange 美国信息交换标准AST Automatic ScanningTracking 自动扫描跟踪ATC Automatic TimingControl 自动定时控制Automatic Tone Correction自动音频校正ATM Asynchronous TransferMode 异步传输模式ATF Automatic Track Finding自动寻迹ATS Automatic Test System自动测试系统ATSC Advanced TelevisionSystems Committee （美国高级电视制式委员会）*＊*C Automatic VolumeControl 自动音量控制*＊*R Automatic VoltageRegulator 自动稳压器AWB Automatic White Balance自动白平衡AZC Automatic ZoomingControl 自动变焦控制AZS Automatic Zero Setting自动调零BA Branch Amplifier 分支放大器Buffer Amplifier 缓冲放大器BAC Binary-AnalogConversion 二进制模拟转换BB Black Burst 黑场信号BBC British BroadcastingCorporation 英国广播公司BBI Beijing BroadcastingInstitute 北京广播学院BC Binary Code 二进制码Balanced Current 平衡电流Broadcast Control 广播控制BCT Bandwidth CompressionTechnique 带宽压缩技术BDB Bi-directional Data Bus双向数据总线BER Basic Encoding Rules 基本编码规则Bit Error Rate 比特误码率BF Burst Flag 色同步旗脉冲BFA Bare Fiber Adapter 裸光纤适配器Brillouin Fiber Amplifier布里渊光纤放大器BGM Background Music 背景音乐BIOS Basic Input／OutputSystem 基本输入输出系统B—ISDN Broadband—ISDN 宽带综合业务数据网BIU Basic Information Unit基本信息单元Bus Interface Unit 总线接口单元BM Bi-phase Modulation 双相调制BML Business ManagementLayer 商务管理层BN Backbone Network 主干网BNT Broadband NetworkTermination 宽带网络终端设备BO Bus Out 总线输出BPG Basic Pulse Generator 基准脉冲发生器BPS Band Pitch Shift 分频段变调节器BSI British Standard Institute 英国标准学会BSS Broadcast Satellite Service 广播卫星业务BT Block Terminal 分线盒、分组终端British Telecom 英国电信BTA Broadband Terminal Adapter 宽带终端适配器Broadcasting Technology Association (日本BTL Balanced Transformer—Less 桥式推挽放大电路BTS Broadcast Technical Standard 广播技术标准BTU Basic Transmission Unit 基本传输单元BVU Broadcasting Video Unit 广播视频型(一种3/4英寸带录像机记录格式BW BandWidth 带宽BWTV Black and White Television 黑白电视CA Conditional Access 条件接收CAC Conditional Access Control 条件接收控制CAL Continuity AcceptLimit 连续性接受极限CAS Conditional Access System 条件接收系统Conditional Access Sub—system 条件接收子系统CATV Cable Television 有线电视，电缆电视Community Antenna Television 共用天线电视C*** Constant Angular Velocity 恒角速度CBC Canadian Broadcasting Corporation 加拿大广播公司CBS Columbia Broadcasting System （美国哥伦比亚广播公司CC Concentric Cable 同轴电缆CCG Chinese Character Generator 中文字幕发生器CCIR International Radio Consultative Committee 国际无线电咨询委员会CCITT International Telegraph and Telephone ConsultativeCommittee 国际电话电报咨询委员会CCR Central Control Room 中心控制室CCTV China Central Television 中国中央电视台Close-Circuit Television 闭路电视CCS Center Central System 中心控制系统CCU Camera Control Unit 摄像机控制器CCW Counter Clock—Wise 反时针方向CD Compact Disc 激光唱片 CDA Current DumpingAmplifier 电流放大器CD—E Compact Disc Erasable可抹式激光唱片CDFM Compact Disc FileManager 光盘文件管理（程序CDPG Compact—Disc PlusGraphic 带有静止图像的CD唱盘CD-ROM Compact Disc—ReadOnly Memory 只读式紧凑光盘CETV China EducationalTelevision 中国教育电视台CF Color Framing 彩色成帧CGA Color Graphics Adapter彩色图形（显示卡CI Common Interface 通用接口CGA Color Graphics Adapter 彩色图形(显示卡CI Common Interface 通用接口CIE Chinese Institute ofElectronics 中国电子学会CII China InformationInfrastructure 中国信息基础设施CIF Common IntermediateFormat 通用中间格式CIS Chinese IndustrialStandard 中国工业标准CLV Constant Linear Velocity恒定线速度CM Colour Monitor 彩色监视器CMTS Cable Modem TerminationSystem 线缆调制解调器终端系统CNR Carrier-to—Noise Ratio载噪比CON Console 操纵台Controller 控制器CPB Corporation of PublicBroadcasting (美国公共广播公司CPU Central Processing Unit中央处理单元CRC Cyclic Redundancy Check循环冗余校验CRCC CRI Cyclic RedundancyCheck Code 循环冗余校验码CROM China RadioInternational 中国国际广播电台CRT Control Read Only Memory控制只读存储器CS Cathode—Ray Tube 阴极射线管CSC Communication Satellite通信卫星CSS Color Sub-carrier 彩色副载波Center Storage Server 中央存储服务器Content Scrambling System 内容加扰系统CSU Channel Service Unit 信道业务单元CT Color Temperature 色温CTC Cassette Tape Controller盒式磁带控制器Channel Traffic Control 通道通信量控制Counter Timer Circuit 计数器定时器电路Counter Timer Control 计数器定时器控制CTE Cable TerminationEquipment 线缆终端设备Customer Terminal Equipment用户终端设备CTV Color Television 彩色电视CVD China Video Disc 中国数字视盘CW Carrie Wave 载波DAB Digital AudioBroadcasting 数字音频广播DASH Digital AudioStationary Head 数字音频静止磁头DAT Digital Audio Tape 数字音频磁带DBMS Data Base ManagementSystem 数据库管理系统DBS Direct BroadcastSatellite 直播卫星DCC Digital Compact Cassette数字小型盒带Dynamic Contrast Control 动态对比度控制DCT Digital ComponentTechnology 数字分量技术Discrete Cosine Transform 离散余弦变换DCTV Digital ColorTelevision 数字彩色电视DD Direct Drive 直接驱动DDC Direct Digital Control直接数字控制DDE Dynamic Data Exchange 动态数据交换DDM Data Display Monitor 数据显示监视器DES Data Elementary Stream数据基本码流Data Encryption Standard 美国数据加密标准DF Dispersion Flattened 色散平坦光纤DG Differential Gain 微分增益DI Digital Interface 数字接口DITEC Digital TelevisionCamera 数字电视摄像机DL Delay Line 延时线DLD Dynamic Linear Drive 动态线性驱动DM Delta Modulation 增量调制Digital Modulation 数字调制DMB Digital MultimediaBroadcasting 数字多媒体广播DMC Dynamic Motion Control动态控制DME Digital Multiple Effect数字多功能特技DMS Digital Mastering System数字主系统DN Data Network 数据网络DNG Digital News Gathering数字新闻采集DNR Digital Noise Reducer 数字式降噪器DOB Data Output Bus 数据输出总线DOCSIS Data Over CableService Interface Specifications有线数据传输业务接口规范DOC Drop Out Compensation 失落补偿DOS Disc Operating System 磁盘操作系统DP Differential Phase 微分相位Data Pulse 数据脉冲DPCM Differential Pulse Code Modulation 差值脉冲编码调制DPL Dolby Pro Logic 杜比定向逻辑DSB Digital Satellite Broadcasting 数字卫星广播DSC Digital Studio Control 数字演播室控制DSD Dolby Surround Digital 杜比数字环绕声DSE Digital Special Effect 数字特技DSK Down-Stream Key 下游键DSP Digital Signal Processing 数字信号处理Digital Sound Processor 数字声音处理器DSS Digital Satellite System 数字卫星系统DT Digital Technique 数字技术Digital Television 数字电视Data Terminal 数据终端Data Transmission 数据传输DTB Digital Terrestrial Broadcasting 数字地面广播DTBC Digital Time—Base Corrector 数字时基校正器DTC Digital Television Camera 数字电视摄像机DTS Digital Theater System 数字影院系统Digital Tuning System 数字调谐系统Digital Television Standard 数字电视标准DVB Digital Video Broadcasting 数字视频广播DVC Digital Video Compression 数字视频压缩DVE Digital Video Effect 数字视频特技DVS Desktop Video Studio 桌上视频演播DVTR Digital Video Tape Recorder 数字磁带录像机EA Extension Amplifier 延长放大器EB Electron Beam 电子束EBS Emergency Broadcasting System 紧急广播系统EBU European Broadcasting Union 欧洲广播联盟EC Error Correction 误差校正 ECN Emergency Communications Network 应急通信网络ECS European Communication Satellite 欧洲通信卫星EDC Error Detection Code 错误检测码EDE Electronic Data Exchange 电子数据交换EDF Erbium—Doped Fiber 掺饵光纤EDFA Erbium-Doped Fiber Amplifier 掺饵光纤放大器EDL Edit Decision List 编辑点清单EDTV Extended Definition Television 扩展清晰度电视EE Error Excepted 允许误差EFM Eight to Fourteen Modulation 8-14调制 EFP Electronic FieldProduction 电子现场节目制作EH Ethernet Hosts 以太网主机EIN Equivalent Input Noise等效输入噪声EIS Electronic InformationSystem 电子信息系统EISA Extended IndustrialStandard Architecture 扩展工业标准总线EL Electro—Luminescent 场致发光EM Error Monitoring 误码监测EN End Node 末端节点ENG Electronic NewsGathering 电子新闻采集EOT End of Tape 带尾EP Edit Point 编辑点Error Protocol 错误协议EPG Electronic Program Guides 电子节目指南EPS Emergency Power Supply应急电源ERP Effective Radiated Power 有效辐射功率ES Elementary Stream 基本码流End System 终端系统ESA European Space Agency 欧洲空间局ETV Education Television 教育电视FA Enhanced Television 增强电视FABM FAS Facial Animation 面部动画FC Fiber Amplifier BoosterModule 光纤放大器增强模块Fiber Access System 光纤接入系统Frequency Changer 变频器FCC Fiber Channel 光纤通道FD Film Composer 电影编辑系统Federal CommunicationsCommission 美国联邦通信委员会FDCT Frequency Divider 分频器FDDI FDM Fiber Duct 光纤管道FDP Forward Discrete CosineTransform 离散余弦正变换FE Fiber Distributed DataInterface 分布式光纤数据接口Frequency-Division Multiplexing频分复用FF Fiber Distribution Point光纤分配点FG Front End 前端FH Framing Error 成帧误差FIT Fast Forward 快进FN Frequency Generator 频率发生器FOA Frequency Hopping 跳频FOC Frame—Interline Transfer帧一行间转移Fiber Node 光纤节点Fiber Optic Amplifier 光纤放大器FOM Fiber Optic Cable 光缆FON Fiber Optic Communications光纤通信FOS Fiber Optic Coupler 光纤耦合器FOTC Fiber Optic Modem 光纤调制解调器FS Fiber Optic Net 光纤网Factor of Safety 安全系数Fiber Optic Trunk Cable 光缆干线FT Frame Scan 帧扫描FTP Frame Store 帧存储器FTTB Frame Synchro 帧同步机FTTC France Telecom 法国电信Absorber Circuit 吸收电路AC/AC Frequency Converter 交交变频电路AC power control交流电力控制AC Power Controller交流调功电路AC Power Electronic Switch交流电力电子开关Ac Voltage Controller交流调压电路Asynchronous Modulation异步调制Baker Clamping Circuit贝克箝位电路Bi—directional Triode Thyristor双向晶闸管Bipolar Junction Transistor-—BJT双极结型晶体管Boost—Buck Chopper升降压斩波电路Boost Chopper升压斩波电路Boost Converter升压变换器Bridge Reversible Chopper桥式可逆斩波电路Buck Chopper降压斩波电路Buck Converter降压变换器Commutation换流Conduction Angle导通角Constant Voltage ConstantFrequency —-CVCF 恒压恒频Continuous Conduction—-CCM（电流)连续模式Control Circuit 控制电路Cuk Circuit CUK 斩波电路Current Reversible Chopper电流可逆斩波电路Current Source Type Inverter--CSTI 电流（源）型逆变电路Cyclo convertor周波变流器DC-AC-DC Converter直交直电路DC Chopping直流斩波DC Chopping Circuit直流斩波电路DC—DC Converter直流－直流变换器Device Commutation器件换流Direct Current Control直接电流控制Discontinuous Conduction mode（电流）断续模式displacement factor 位移因数distortion power 畸变功率double end converter 双端电路driving circuit 驱动电路electrical isolation 电气隔离fast acting fuse 快速熔断器fast recovery diode快恢复二极管fast revcovery epitaxial diodes快恢复外延二极管fast switching thyristor快速晶闸管。
工业常用语中英文对照表
business transaction 商业交易 buster 堵口 butt welding 对接焊接 button die 镶入式圆形凹模 buyer 买方 buzzle蜂鸣器 bypass heat treatment 旁路热处理
Cycle Time 制程周期 Computer Aid Design 计算机辅助设计 Computer AID Engineering 计算机辅助分析 calendaring molding 压延成形 calibration 校准 caliper gauge 卡规 Computer AID Manufacturing 计算机辅助加工 cam block滑块 cam die bending 凸轮弯曲加工 cam driver铡楔 camber 电弧、弯曲 、翘曲 camlachie cramp 铸包 capability能力 Correction Action Report 改善报告 corrective action request 改正行动要求 carbide 炭化物 carbon copy 打字副本 carbon tool steel 碳素工具钢 carbonization碳化 carburized case depth 浸碳硬化深层 carburizing 渗碳 career card履历卡 cargo collection 揽货 carton box纸箱 carton纸箱 cascade 阶叠熔接法 casein 酪素 cash in advance 预付现金 casing = containerazation装箱 cassette 卡座 cast blade 铸造叶片 casting flange 铸造凸缘
Average Output Quality 平均出厂品质 Average Output Quality Level 平均出厂品质 Approve 核准,认可,承认 application form for purchase请购单 application 应用 approved by / checked by / prepared by核准/审核/承办 Acceptable Quality Level 运作类允收品质水准 Averary Range 全范围平均值 arbour 心轴 arc discharge 电弧放电 arc 电弧 argon arc welding 氩弧焊接 argon welding氩焊 assembly drawing 装配图 Assembly line组装线 assembly mark 装配记号 assistant manager助理 Asssembly 组装(厂) ASS'Y Assembly 装配,组装 at sight 见票即付 Attention 知会 atomization 雾化 atomloy treatment 阿托木洛伊表面 augular offset角度偏差 austempering 奥氏体等温淬火 austenite 奥氏田体/奥氏体 austenitic steel 奥氏田铁钢 auto tool change cycle 自动换刀时间周期 autocollimator 自动准直机 automatic screwdriver电动启子 automation自动化 auxiliary fuction辅助功能
模具英语词汇大全
汽车冲压模具英语词汇Die / Tool= 模具Prog。
Die=progressive die 级进模Ball bearing guide posts and bushings=球形滚珠导柱和轴套Casting die=铸造模Cage=套Part=钣件Rigidity=强度Die material=制模材料Thin=薄Tool design=模具设计Strip design=料条设计Using material thickness radii where sharp corners are shown on the part reduces the occurrence of chipped punch or die corners in the tool. =在尖角处使用与材料厚度一样的R角减少冲头碎裂或模具中有“刀口"Tool design approval=模具设计审核Tool design modification/revision=模具设计更改Tool parts design (detail) = 模具钣件设计（详细）Heeled die sets, internally heel form ＆trim sections=带箱根的模架，成形与切刃冲头带导引FMC Make=保丽龙制作Construction method=结构方法modification= 更改Check & measure=检查& 测试Machining= 机器加工Large machining=在大型机器上加工上下模架（铣、车等）Small machining=在小型机器上加工模块等Lower die trim inserts=下模切刃块Lower trim inserts retainer=下模切刃块承盘Assemble inserts=组立镶块Punch stripping plates=冲头压料板Assembly=组立Trim punch backing plates=切刃冲头背板NC Machining=NC雕刻加工Stripper window inserts=料条窗户镶块Fitting=研磨组立Spotting=合模Die tryout=试模Cushing stroke=缓冲行程Dowel pin=定位销Guide lift pin=导引升降销Assemble gas spring=安装氮气缸Stamp parts=冲钣件Adjustment=调试Run off parts=冲钣件Lower trim steels=下刃块Hit parts=冲钣件Section=冲头断面Lifters=提升器Trim punch=切刃冲头Coil=卷材jack screw hole=起重［千斤顶]螺旋孔Guide block=导引块Die set，lower plate=下模架Guide the coil through the tool=导引卷材Die set, upper plate=上模架layout inspection=全尺寸检验Die inspection & approval=模具检查和审核Stretch carriers=拉伸运送装置delivery=发货Punch stripping plates=冲头压料板Rejected=拒收Trim punch backing plates=切刃冲头背板Scrapped=报废Stripper window inserts=料条窗户镶块Rework=返工Heel plates=背托stop block=停止块Prepare for delivery=准备发货Hydro form 液压成形Key=键Shear=剪切For locating retainer blocks=承盘键Sensor=传感器For holding buttons or pilots=冲母座或导销键Stretch web=拉伸网For fixed heel or positive stop=镶根键Layout the parts=设计钣件Construction method=结构方法Preceding into the design=继续设计Manual Surface Grinder=手动平面磨床Guide the coil through the tool=导引卷材Spotting red=合模用丹红Checking aid /checking gage=检具Layout ink=试模用蓝墨水Jig=夹具Masking tape=黄色不透明胶带(遮蔽胶带）Fixture=夹具Pliers=尖嘴钳，老虎钳Ball bearing guide posts and bushings=球形滚珠轴套Cresent wrench=可调扳手Guide post=导柱Bushings=导套Pump pipe=泵管Using material thickness radii where sharp corners are shown on the part reduces the occurrence of chipped punch or die corners in the tool. =在尖角处使用与材料厚度一样的R 角减少冲头碎裂或模具中有“刀口”CMM=三次元测量仪Symmetric=对称的The axis of symmetry=对称轴Technical=技术上的Diagonal=对角线Heeled die sets, internally heel form ＆trim sections=带箱根的模架，成形与切刃冲头带导引One two three block=一二三模块Adjustable parallels=可调平行块Stop block=阻止块Granite Table=花岗岩平台Backing Plate=背板Plotter= 。
插脚安规尺寸
VDE PLUG DIMENSION (mm)Two-pin plugs for class II appliances (Up to 2.5 A rating)According to EN50075 - Standard Sheet and IEC60083 - Standard C5金属下部结合部分边缘应光滑钝化，不得尖锐刺手。
欧洲VDE PLUG DIMENSION CHECK LIST.从外壳圆周面延伸到PIN脚与托台结合处任意点之间的距离最小为18mmDimension Checking for Two-pin plugs of NA (15 A, 125 V)According to ANSI/UL 1310 and ANSI/UL 1861 (NEMA Figure 1-15)UL PLUG DIMENSION CHECK LIST公差为± 0.127mm符号标准值 (mm) 测量值(mm) 符号标准值(mm) 测量值 (mm)A 3.175 E 6.60≥ E ≥ 6.09B 3.96 F 8.17 ≥ F ≥ 7.80C 13.77G 1.65 ≥ G ≥ 1.40D 18.23 ≥ D ≥ 15.86 H 12.7起始于金属插脚的任意一点，与金属插脚的托台圆周边之间的距离不得小于7.9 mmAccording to Figure 4 of BS1363Grounding pinBS PLUG DIMENSION CHECK LIST.英SAA PLUG DIMENSION (mm)澳According to AS/NZS 3112:1993 Two-pin plugs (Up to 10 A rating)符号标准值 (mm) 测量值(mm) 符号标准值 (mm) 测量值(mm)A < 21.9 or > 27.0 H 1.58 – 1.78B < 21.9 or > 27.0 I 16.66 – 17.46C < 21.9 or > 27.0 J 8.6minD < 21.9 or > 27.0 K R 21.0 maxE 60 L R 19.0 – 21.0F 6.2 – 6.5 M R 1.0 maxG 7.92According to AS/NZS 3112:1993 Three-pin plugs (10 A or 15A rating)符号标准值(mm) 测量值(mm) 符号标准值 (mm) 测量值(mm)A 6.2 ～ 6.5 J < 21.9 or > 27.0B 6.2～ 6.5 K < 21.9 or > 27.0C 1.58 ～ 1.78 L 60 ︒D 7.92 M 60 ︒E 10.31 N 8.6minF 16.66 ～ 17.46 O R 19.0 – 21.0G 19.14 ～ 20.74 P R 21.0 maxH < 21.9 or > 27.0 Q R 1.0 maxI < 21.9 or > 27.0According to Fig 1 of GB 1002-1996 Tow-pin plugs (6 A, 10 A rating)CHINA PLUG DIMENSION CHECK LIST.符号标准值(mm) 测量值(mm)A 1.4 ~ 1.5B 6.18 ~ 6.4C 12.565 ~ 12.835D 15.65 ~ 16.35According to Fig 1 of GB 1002-1996 Three-pin plugs (Up to 6 A rating)CHINA PLUG DIMENSION CHECK LIST.符号标准值 (mm) 测量值 (mm)A 120B 7.79 – 8.01C 1.4 – 1.5D 6.18 – 6.4E 20.58 – 21.42F 17.65 – 18.35According to KSC 8305 Two-pole plug for 3A 250VKOREA PLUG DIMENSION CHECK LIST.JAPAN PLUG DIMENSION (mm)According to EMA Figure 1-15 Two-pin plugs of JP (15 A, 125 V)JAPAN PLUG DIMENSION CHECK LIST.符号标准值(mm) 测量值(mm) 符号标准值 (mm) 测量值(mm)A 3.3 ≥ A ≥2.8 E 6.6 ≥ E ≥ 6.0B 3.5以上 F 8.2 ≥ F ≥ 7.8C 13.75≥ C ≥ 12.7G 1.6 ≥ G ≥1.4D 18.3 ≥ D ≥ 15.7 H 12.7起始于金属插脚的任意一点，与金属插脚的托台圆周边之间的距离不得小于7.9 mm金属插脚孔内圆中心到插脚托台面的距离为11.7±0.4金属PIN脚末端厚度为0.9mm以下。
中英模具用语翻译对照
English Chinese(specification of)scrap pit/scrap hole废料坑、废料槽(when) at a bottom/closed position下死点（时）(when) holding a pad加工开始（时）(when）bend starts弯曲开始(when)flange starts弯曲开始90 degree to the surface/right angle to the面垂直surfacea bead is selected to satisfy form选择符合成形内容的筋a block to adjust pressure压力调整块a built-in cam内藏斜锲a scrap chute which is out of die is proper模具外的滑槽的保管性是否良好to stocka way of jaw/penetration groove for jaw爪进入槽A.C.motor交流马达ability of forming pressure成形力acceleration加速acceptance/approval接受access/proximity接近accuracy of panel or part零件精度accuracy/tolerance精度acetylene gas cutter乙炔切割机acute/pinch cut/knife edge锐角adapter插座addendum毛边形状addendum铸件防变形用拉深形状addendum/draw development/punch addendum铸件防变形用拉深adhesive黏附性的adility to assemble装配型adility/capacity能力adjust调整adjustable gib调整式扁栓adjustable stop调整式停止装置adjusted length调整长度adjusted size调整尺寸adjusting allowance调整余量adjusting pad slide卸料板落料adjusting screw/aircraft valve调整螺钉adjusting to suit复合调整adjustment调整adjustment调节adjustment plate/baffle plate调整板advance前进aerial cam slide滑块after form/formed…成形后after treatment后处理air bending/free bending自由弯曲air blast喷气air blow喷气嘴air blow空气喷嘴air blow off放气air chute空气槽air circuit/air piping空气配管air condition调整空气air cushion气垫air cylinder气缸air draw气动拉延air duct空气导管air filter空气配管滤清器air filter/air strainer空气净化器air forming die自由成形模air hammer气锤air header block缸体air hole气孔air inlet吸气口air leakage气体泄漏air lifter弹顶器air outlet放气口air pin气垫用销air pin/pressure pin/cushion pin/transfer弹顶杆pinair pocket气泡air pocket/hole风孔air pusher气体推顶air relief/air escapement排气air surge tank空气稳压箱air vent排气孔air vent hole排气孔air vent tube排气管air ventilation通风，换气air ventilation通风装置Align排成一列Align排成一条线alignment定心all operations全工序alloy合金alternate交互的alternating bend test反复弯曲试验alternating current 交流电流alternating current arc welder交流电弧焊机alternative press备用压机aluminum bronze铝青铜aluminum plate/aluminum panel铝板amend重新amend/modify/correct修正amendment/correction修正amount of picking up a panel零件挑出量amount of product/production quantity生产量amount of spring back回弹量An auto clamper is used自动接线板的使用analyze分析anchor bolt地角螺栓anchor strap紧固夹板angle角度angle block/square block角尺angle grinder圆盘磨光机angle iron角钢angle of grinding/approach of grinding打磨机的插入angle shearing machine角材剪切机annealing退火annealing furnace退火炉annealing to eliminate internal stresses消除应力退火apparent stress公称应力appear/show图示appearance外观applied parts适用零件approach speed接近速度apron front fender前翼子板挡板arber press压入冲压机arc圆弧arc弧arc welding电弧焊arc welding rod电焊条are all scrap cutters strong enough?废料刀口是否有变薄弱处？are the hook pins strong enough to lift with2根起吊时确认吊钩尺寸two wiresare there any acute angles of trim steel?刃口处是否有锐角？are there any vertical wall which need to是否有纵向切削部trim?area of door handle门把手arrangement 配置arrangement for 2nd maching机械加工2次准备arrangement/pre-fitting准备工序ask contractor to design委托设计assemblage集团assemble/fabricate组装assembling drawing/complete assembly组图assumed line点划线attach 添付attach/mount/furnish/equip/fix安装auger木工钻头austenite奥氏体automatic die change自动更换模具automatic slide control滑块自动调整装置auxiliary air tank备用空气冠back door inner后背门内板back door outer后背门外板back panel lower后板下部back panel upper后板上部back shelf panel后搁板back up/cast step背撑backing plate垫板（底板）backing ring垫环，环垫balance/counter-balance平衡balancing cylinder平衡气缸ball bearing球轴承ball bearing球轴承ball bearing die set球轴承式调模ball lock 球锁定ball lock retainer钢球止转式挡板ball screw球螺钉bar杆，拉杆bar lifter杆式升降器base台座base frame底部基座base plate底板base plate/surface plate平台，平板base/foundation基座beam衡量bearing mounting轴承安装bearing point轴承点bearing support轴承支架bearing/spotting研配bed area底面积bed dimension压机座尺寸bed opening底部口部bed/pree bed底部、基部bell crank arm锥形曲轴臂belling报时加工belt conveyer带式输送机belt piece传送带部件bend弯曲的bend punch/flanging punch弯冲头bend/bending弯曲bending fixture折弯夹具beryllium copper铍铜bevel angle斜角bevel gear锥齿轮beveled die edge斜刃binder pressure 缓冲器负载Binder pressure/Blank holder pressure压板力Binder spotting压板面对接binder/binder surface/binder flash模具型面black grind stone黑石blank and draw die落料拉延模blank holder/binder压边圈blank holder/binder防皱装置Blank holder/Pressure pad压板Blank lay out/gauging板材下料Blank lay out/gauging板材下料计划Blank lay out/gauging板材下料布置blank shape of a formal panel成形后的落料形状blank size坯料尺寸blank/stock原料blanking die/blanking tool落料模blanking force冲模力blanking press/punch press冲模blanking punch冲头blanking tolerance落料公差blanking tool落料工具blanking/punching落料blend off渐渐融合blind bead/closed bead盲孔筋blow hole镶块blunt钝bonnet inner机罩内板bonnet outer机罩外板borax硼砂bore镗孔bore expand test/drift test扩孔试验boss凸起bottom surface底面bottoming底bottoming block底块bottoming plate底板bottoming surface底座面box bending箱弯曲brace支柱brass黄铜brass黄铜brass flat head socket screwbrass liningbrazing/braze钎焊break line/character line特征线break line/cutting plance line破裂线，折断线break molding落砂breaking load破坏载荷，断裂荷重breaking load断裂载荷brittleness脆性bucking/folding/formation of wrinkle/wrinkle褶皱的发生formationbuckle/distortion歪斜，形变buckle/distortion/curl up/kink扭转、螺旋buff抛光bulging中央凸起burn out/burn烧环burner 喷枪burr毛刺burring内缘饭边burring/plunging孔翻边成型burst 胀破burst hole胀裂孔burst punch胀裂冲头buy-off验收bypass接续cable电线caharateristic/property特性calculation of development of material计算线长calculation of pressure/force/load载荷设定cam holder滑块用倾斜工作台cam holder倾斜架cam slide bottom plate滑块底板cam slide keeper plate/slide keeper滑块定位件cam slide side plate滑块侧板camber上翘camber侧倾，翘曲cap screw/socket bolt凹头螺钉capacity容量capacity of crank press曲柄式压力机的能力capstan卷绕车轴carbide draw ring超硬拉深环carbide punch超硬冲头carbonzing and harden渗碳淬火carburizing渗碳carry two dies in same time2模重叠起吊carve刻case hardening表面渗碳硬化处理cast in hole/core/cored hole铸件表面粗糙度Cast in hook整体铸造吊耳cast iron铸铁Cast letter/Cast on die铸造文字Cast out/notched hole/core/core pocket/cored铸件减重孔openingcast steel/tool steel casting/steel casting铸钢cast/casting/foundry铸造性cast/iron铸件构成物casting铸件casting pattern模型（铸件用的) casting steel铸钢件casting structure铸件气泡孔caulking/calking铆接caulking/calking,caulk/crimp铆接cavity凹处cavity/collapse/depression凹处、凹面cement steel渗碳钢cemented carbide tool超硬工具center floor中地板center line中心线center of gravity重心center of pressure压力中心center pillar中立柱center punch中心冲头centralize聚集在中央chamfer angle倒角chamfer，chamfered倒角chamfering倒角作业change of dimension尺寸变更chart图表checking fixture/inspection fixture检具chemical components化学成分chip breaker/slug breaker/scrap breaker断屑槽chipped edge/nicked edge卷刀chipped punch刃口崩chipping缺损chisel凿子chisel钢凿chute 槽chuter滑槽circuit回路circuit diagram回路图circuit of pipe配管经路circumferential strain圆周方向变形clamp 夹紧clamp/yoke U字钉clamping fixture/fixture/shank安装工具clamping slot U槽class"1"surface/outer skin surface外部形面claw bar巴clay粘土clay model油泥模型clearance落料间隙clearance间隙clearance 间隙clearance between a blank holder and a lower底面间隙shoeclearance hole/body drill自由尺寸孔clevis U型连接器clip/clamp夹钳、钳closed joint无间隙焊接closing in压环clutch离合器clutch actuating level离合器作动杠杆clutch operating time离合器作动时间clutch/coupling/fitting接头coarse particulate/dust粉尘coarse thread标准螺纹coefficient of expansion膨胀系数coil cradle卷材芯coil feed卷材的送给coil feeder卷材送给装置coil/strip卷材coiled spring/helical spring螺旋弹簧coiler卷绕机coiling卷绕作业coining整形coining die压印加工模cold drawn冷轧cold rolling/cold roll常温压延cold shortness冷脆性collapse压碎Collar环collar环，圈column圆柱combination die组合模combined error/overall error综合误差combustion有机体的氧化commercial item现成品common specification of design设计统一规格书compacting预安装compo/mortar灰泥component构成品Composite die section分型模构成要素compressive ratio压缩比concave凹陷concave凹形的concentricity同心度/同轴度condition of die spotting in principal模具磨配重要管理部control areacone圆锥形conical/conic圆锥形的connecting rod连接棒connecting strap连接金属箍、连接金属带connection接续connection rod连接棒constant常数contour外形contour drawing外形图contour gauge/profile gauge轮廓样板，轮廓量规contour/profile轮廓contraction/necking缩劲control valve/flush plug调节阀control/controller控制converting可变阀convex凸型的convex凸状的convex shear凸型剪切conveyer搬运装置conveyer system/flow operation流水作业方式coolant/quenching liquid冷却液cooling冷却cooling rate冷却速度coordinating hole坐标孔core中心core bar /mandrel心轴core for air relief排气孔corner pillar角立柱corner R R角corner rounding倒角corrected修正完correction after try out试模修正correr post角柱cost reduction降低成本cost/first cost/initial cost原价countemeasure for safety/ precaution安全对策countermeasure对策countermeasure对应法cowl发动机罩cowl side inner发动机罩侧内板cowl top inner发动机罩上内板cowl top outer发动机上罩板crack裂纹、裂缝crack/fracture/scoring/slit裂纹、裂缝crane吊车crank pin曲柄销crank plate曲柄板crank press曲柄式压力机crank/crank shaft曲轴crawling蠕动critical极限的critical forming area成形困难部critical load极限载荷critical surface area机能面cropping棒的切断cross arm托架cross bar十字杆cross bar transfer十字杆传送cross key十字键cross section/transverse section横断面crossbar knockout纵横脱模crosshead十字头curl up/roll弯曲curling die卷边模current transformer/electrical transformer变压器curve弯曲cushion缓冲垫cushion pad缓冲气垫cushion pin/pressure pin弹顶杆cushion pressure缓冲器负荷cushion stroke缓冲器行程cushion stroke机械缓冲垫行程cut edge剪切口cut off切断cut/shear切断cutter刀具cutting allowance切削量cutting die/shear die切断模cutting edge刃口cutting edge 剪切刃cutting edge/trim steel/trim edge修边刃cutting face切刃面cutting land/length of cut/flute length刃长cutting torch气体熔断器cylinder圆筒cylinder 气缸cylinder nut气缸盖螺母cylindrical 圆柱状的cylindrical square柱形量规damaged/damage损伤dash panel仪表板dash panel side仪表板侧面dash riser panel仪表板垫板data数据datum hole加工基准孔datum line/zero line基准线datum surface加工基准面datum surface/nets基准面daylight/open height开口高度deck lid inner车箱盖内板deck lid outer车箱盖外板decoiling开卷作业decoiling device 回绕装置decoiling device/uncoiler开卷机decomposition/resolution分解defect/fault缺陷definition定义deflect偏差deflect使偏斜deflection偏斜deflection at center of bed 底部（压机工作台）中心的弯度、偏移deflection/deviation偏差deformation pattern变形模板deformation processing变形加工deformation resistance curve变形电阻曲线de-grease去处油delay延误delivery送货delivery出厂density浓度dents and dingsdepression for setting调整座depression for stock保管座depression/hollow/dimple凹处dereeler开卷机desigen review设计审查design构思design设计design engineering设计技术design modification/engineering change设计变更design review审图designed radius制件R designer设计者detail 详细图detail schedule小日程detail/detail of data详细detent制动器determine the feed height进给高度设定development展开/展开形状Deviation超出deviation偏转deviation偏移device/equipment装置diagonal对角线的dial gauge标度规diamond file金刚石锉刀die模具die 模具die assembly模具装配die back up plate模具加强板die block模块die bushing模具镶套die button模具凹模die button retainer凹模座die casting模具等级die clearance模具间隙die component模具构成部件die construction模具结构die cushion模具缓冲机构die depth模具深度die engineering department模具技术部门die height模具高度die holder/die retainer模座die layout加工要领图die lifter起模装置die mark碰痕die mark模具标记die radius模具Rdie set调整die set模组die shoe模座die shouder模具肩部die space模具空间die spotting模具研磨die spotting press模具对研机die steel/tool steel型钢die width模具宽dimension尺寸/记录尺寸dimension line尺寸线dimensional accuracy尺寸精度dimensional drawing尺寸图dimensional tolerance/tolerance of dimension尺寸公差dimple凹坑dimple定缝销钉dimpling die压凹模dinking切断direct current直流direct slide直滑动direction of feed/direction of flow/part送给方向flowdirection of press加工方向directionality方向性disappearing gauge/flip gauge定位块disassembling分解作业disk/disc圆盘disposal/treatment处理dispose处理distack feeder送料器Distance轻倒角distance block限程块distortion/curve弯曲、变形distortion/deformation/variant变形distributed load分布载荷document文件、文本door hinge reinforcement门铰链加强件double action双动double action双动double attached左/右件一体成型double cam双斜锲Double fold板重合double gripper feed双面夹钳式松辽装置double row arrangement双行排料double wear plate双防磨板dowel hole定位销孔dowel pin定位销、顶销dowel pin to suit复合顶销drag back毛刺，飞边drain hole排水孔draw as much as possible to consist of trim修边线极力调整到克修正的部位linedraw bending卷弯draw die development/binder /the draw堆油粘土draw part拉延零件draw punch opening拉延冲头外形draw sheet loader拉延板装卸机drawing 制图drawing/design图纸drawn panel拉延板 dressing stone修整工具drill 钻头drilled hole机械加工孔driver 传动器driver arm动力传导部driver arm驱动臂ductility延展性durability耐久性duration耐久dutchman防止落下dwell cam对置斜锲dynamic interference动干涉dynamic load动载荷dynamic review/line die dynamic check动检查E/C(engineering change) level设计变更NO。