锻造专业英语
有色金属专业英语词汇
有色金属专业英语词汇钢铁的制造Manufacturing of Steel连续铸造法Continuous casting process电炉Electric furnace均热炉Soaking pit全静钢Killed steel半静钢Semi-killed steel沸腾钢(未净钢) Rimmed steel钢铁生产流程Steel Production Flow Chart钢材的熔铸、锻造、挤压及延轧The Casting, Fogging, Extrusion, Rolling & Steel熔铸Casting锻造Fogging挤压Extrusion延轧Rolling冲剪Drawing & stamping特殊钢Special Steel简介General特殊钢以原素分类Classification of Special Steel according to Element特殊钢以用途来分类Classification of Special Steel according to End Usage 易车(快削)不锈钢Free Cutting Stainless Steel含铅易车钢Leaded Free Cutting Steel含硫易车钢Sulphuric Free Cutting Steel硬化性能Hardenability钢的脆性Brittleness of Steel低温脆性Cold brittleness回火脆性Temper brittleness日工标准下的特殊钢材Specail Steel according to JIS Standard铬钢–日工标准JIS G4104Chrome steel to JIS G4104铬钼钢钢材–日工标准G4105 62Chrome Molybdenum steel to JIS G4105镍铬–日工标准G4102 63Chrome Nickel steel to JIS G4102镍铬钼钢–日工标准G4103 64Nickel, Chrome & Molybdenum Steel to JIS G4103高锰钢铸–日工标准High manganese steel to JIS standard片及板材Chapter Four-Strip, Steel & Plate冷辘低碳钢片(双单光片)(日工标准JIS G3141) 73 - 95Cold Rolled (Low carbon) Steel Strip (to JIS G 3141)简介General美材试标准的冷辘低碳钢片Cold Rolled Steel Strip American Standard – American Society for testing and materials (ASTM)日工标准JIS G3141冷辘低碳钢片(双单光片)的编号浅释Decoding of cold rolled(Low carbon)steel strip JIS G3141材料的加工性能Drawing abillity硬度Hardness表面处理Surface finish冷辘钢捆片及张片制作流程图表Production flow chart cold rolled steel coil sheet冷辘钢捆片及张片的电镀和印刷方法Cold rolled steel coil & sheet electro-plating & painting method冷辘(低碳)钢片的分类用、途、工业标准、品质、加热状态及硬度表End usages, industrial standard, quality, condition and hardness of cold rolled steel strip 硬度及拉力Hardness & Tensile strength test拉伸测试(顺纹测试)Elongation test杯突测试(厚度: 0.4公厘至1.6公厘，准确至0.1公厘3个试片平均数)Erichsen test (Thickness: 0.4mm to 1.6mm, figure round up to 0.1mm)曲面(假曲率)Camber厚度及阔度公差Tolerance on Thickness & Width平坦度(阔度大于500公厘，标准回火)Flatness (width>500mm, temper: standard)弯度Camber冷辘钢片储存与处理提示General advice on handling & storage of cold rolled steel coil & sheet防止生锈Rust Protection生锈速度表Speed of rusting焊接Welding气焊Gas Welding埋弧焊Submerged-arc Welding电阻焊Resistance Welding冷辘钢片(拉力: 30-32公斤/平方米)在没有表面处理状态下的焊接状况Spot welding conditions for bared (free from paint, oxides etc) Cold rolled mild steel sheets(T/S:30-32 Kgf/ μ m2)时间效应(老化)及拉伸应变Aging & Stretcher Strains日工标准(JIS G3141)冷辘钢片化学成份Chemical composition – cold rolled steel sheet to JIS G3141冷辘钢片的"理论重量"计算方程式Cold Rolled Steel Sheet – Theoretical mass日工标准(JIS G3141)冷辘钢片重量列表Mass of Cold-Rolled Steel Sheet to JIS G3141冷辘钢片订货需知Ordering of cold rolled steel strip/sheet其它日工标准冷轧钢片(用途及编号)JIS standard & application of other cold Rolled Special Steel电镀锌钢片或电解钢片Electro-galvanized Steel Sheet/Electrolytic Zinc Coated Steel Sheet简介General电解/电镀锌大大增强钢片的防锈能力Galvanic Action improving Weather & Corrosion Resistance of the Base Steel Sheet上漆能力Paint Adhesion电镀锌钢片的焊接Welding of Electro-galvanized steel sheet点焊Spot welding滚焊Seam welding电镀锌(电解)钢片Electro-galvanized Steel Sheet生产流程Production Flow Chart常用的镀锌钢片(电解片)的基层金属、用途、日工标准、美材标准及一般厚度Base metal, application, JIS & ASTM standard, and Normal thickness of galvanized steel sheet锌镀层质量Zinc Coating Mass表面处理Surface Treatment冷轧钢片Cold-Rolled Steel Sheet/Strip热轧钢片Hot-Rolled Sheet/Strip电解冷轧钢片厚度公差Thickness Tolerance of Electrolytic Cold-rolled sheet热轧钢片厚度公差Thickness Tolerance of Hot-rolled sheet冷轧或热轧钢片阔度公差Width Tolerance of Cold or Hot-rolled sheet长度公差Length Tolerance理论质量Theoretical Mass锌镀层质量(两个相同锌镀层厚度)Mass Calculation of coating (For equal coating)/MM锌镀层质量(两个不同锌镀层厚度)Mass Calculation of coating (For differential coating)/MM镀锡薄铁片(白铁皮/马口铁) (日工标准JIS G3303)简介General镀锡薄铁片的构造Construction of Electrolytic Tinplate镀锡薄钢片(白铁皮/马日铁)制造过程Production Process of Electrolytic Tinplate锡层质量Mass of Tin Coating (JIS G3303-1987)两面均等锡层Both Side Equally Coated Mass两面不均等锡层Both Side Different Thickness Coated Mass级别、电镀方法、镀层质量及常用称号Grade, Plating type, Designation of Coating Mass & Common Coating Mass 镀层质量标记Markings & Designations of Differential Coatings硬度Hardness单相轧压镀锡薄铁片(白铁皮/马口铁)Single-Reduced Tinplate双相辗压镀锡薄钢片(马口铁/白铁皮)Dual-Reduction Tinplate钢的种类Type of Steel表面处理Surface Finish常用尺寸Commonly Used Size电器用硅[硅] 钢片Electrical Steel Sheet简介General软磁材料Soft Magnetic Material滞后回线Narrow Hystersis矫顽磁力Coercive Force硬磁材料Hard Magnetic Material最大能量积Maximum Energy Product硅含量对电器用的低碳钢片的最大好处The Advantage of Using Silicon low Carbon Steel晶粒取向(Grain-Oriented)及非晶粒取向(Non-Oriented)Grain Oriented & Non-Oriented电器用硅[硅] 钢片的最终用途及规格End Usage and Designations of Electrical Steel Strip电器用的硅[硅] 钢片之分类Classification of Silicon Steel Sheet for Electrical Use电器用钢片的绝缘涂层Performance of Surface Insulation of Electrical Steel Sheets晶粒取向电器用硅钢片主要工业标准International Standard – Grain-Oriented Electrical Steel Silicon Steel Sheet for Electrical Use晶粒取向电器用硅钢片Grain-Oriented Electrical Steel晶粒取向，定取向芯钢片及高硼定取向芯钢片之磁力性能及夹层系数(日工标准及美材标准)Magnetic Properties and Lamination Factor of SI-ORIENT-CORE& SI-ORIENT-CORE-HI B Electrical Steel Strip (JIS and AISI Standard)退火Annealing电器用钢片用家需自行应力退火原因Annealing of the Electrical Steel Sheet退火时注意事项Annealing Precautionary碳污染Prevent Carbon Contamination热力应先从工件边缘透入Heat from the Laminated Stacks Edges提防过份氧化No Excessive Oxidation应力退火温度Stress –relieving Annealing Temperature晶粒取向电器用硅[硅] 钢片–高硼(HI-B)定取向芯钢片及定取向芯钢片之机械性能及夹层系数Mechanical Properties and Lamination Factors of SI-ORIENT-CORE-HI-B and SI-ORIENT-CORE Grain Orient Electrical Steel Sheets晶粒取向电器用硅[硅] 钢;片–高硼低硫(LS)定取向钢片之磁力及电力性能Magnetic and Electrical Properties of SI-ORIENT-CORE-HI-B-LS晶粒取向电器用硅[硅] 钢片–高硼低硫(LS) 定取向钢片之机械性能及夹层系数Mechanical Properties and Lamination Factors of SI-ORIENT-CORE-HI-B-LS晶粒取向电器用硅(硅)钢片-高硼(HI-B)定取向芯钢片，定取向芯钢片及高硼低硫(LS)定取向芯钢片之厚度及阔度公差Physical T olerance of SI-ORIENT-CORE-HI-B, SI-ORIENT-CORE, & SI-CORE-HI-B-LS GrainOriented Electrical Steel Sheets晶粒取向电器用硅(硅)钢片–高硼(HI-B)定取向芯钢片，定取向芯钢片及高硼低硫(LS)定取向芯钢片之标准尺寸及包装Standard Forms and Size of SI-ORIENT-CORE-HI-B,SI-CORE, & SI-ORIENT-CORE-HI-B-LS Grain-Oriented Electrical Steel Sheets绝缘表面Surface Insulation非晶粒取向电力用钢片的电力、磁力、机械性能及夹层系数Lamination Factors of Electrical, Magnetic & Mechanical Non-Grain Oriented Electrical电器及家电外壳用镀层冷辘[低碳] 钢片Coated (Low Carbon) Steel Sheets for Casing,Electricals & Home Appliances镀铝硅钢片Aluminized Silicon Alloy Steel Sheet简介General镀铝硅合金钢片的特色Feature of Aluminized Silicon Alloy Steel Sheet用途End Usages抗化学品能力Chemical Resistance镀铝(硅)钢片–日工标准(JIS G3314)Hot-aluminum-coated sheets and coils to JIS G 3314镀铝(硅)钢片–美材试标准(ASTM A-463-77)35.7 JIS G3314镀热浸铝片的机械性能Mechanical Properties of JIS G 3314 Hot-Dip Aluminum-coated Sheets and Coils公差Size Tolerance镀铝(硅)钢片及其它种类钢片的抗腐蚀性能比较Comparsion of various resistance of aluminized steel & other kinds of steel镀铝(硅)钢片生产流程Aluminum Steel Sheet, Production Flow Chart焊接能力Weldability镀铝钢片的焊接状态(比较冷辘钢片)Tips on welding of Aluminized sheet in comparasion with cold rolled steel strip钢板Steel Plate钢板用途分类及各国钢板的工业标准包括日工标准及美材试标准Type of steel Plate & Related JIS, ASTM and Other Major Industrial Standards钢板生产流程Production Flow Chart钢板订货需知Ordering of Steel Plate不锈钢Stainless Steel不锈钢的定义Definition of Stainless Steel不锈钢之分类，耐腐蚀性及耐热性Classification, Corrosion Resistant & Heat Resistance of Stainless Steel铁铬系不锈钢片Chrome Stainless Steel马氏体不锈钢Martensite Stainless Steel低碳马氏体不锈钢Low Carbon Martensite Stainless Steel含铁体不锈钢Ferrite Stainless Steel镍铬系不锈钢Nickel Chrome Stainless Steel释出硬化不锈钢Precipitation Hardening Stainless Steel铁锰铝不锈钢Fe / Mn / Al / Stainless Steel不锈钢的磁性Magnetic Property & Stainless Steel不锈钢箔、卷片、片及板之厚度分类Classification of Foil, Strip, Sheet & Plate by Thickness表面保护胶纸Surface protection film不锈钢片材常用代号Designation of SUS Steel Special Use Stainless表面处理Surface finish薄卷片及薄片(0.3至2.9mm厚之片)机械性能Mechanical Properties of Thin Stainless Steel(Thickness from 0.3mm to 2.9mm) –strip/sheet不锈钢片机械性能(301, 304, 631, CSP)Mechanical Properties of Spring use Stainless Steel不锈钢–种类，工业标准，化学成份，特点及主要用途Stainless Steel – Type, Industrial Standard, Chemical Composition, Characteristic & end usage of the most commonly used Stainless Steel不锈钢薄片用途例End Usage of Thinner Gauge不锈钢片、板用途例Examples of End Usages of Strip, Sheet & Plate不锈钢应力退火卷片常用规格名词图解General Specification of T ension Annealed Stainless Steel Strips耐热不锈钢Heat-Resistance Stainless Steel镍铬系耐热不锈钢特性、化学成份、及操作温度Heat-Resistance Stainless Steel铬系耐热钢Chrome Heat Resistance Steel镍铬耐热钢Ni - Cr Heat Resistance Steel超耐热钢Special Heat Resistance Steel抗热超级合金Heat Resistance Super Alloy耐热不锈钢比重表Specific Gravity of Heat – resistance steel plates and sheets stainless steel不锈钢材及耐热钢材标准对照表Stainless and Heat-Resisting Steels高碳钢片High Carbon Steel Strip分类Classification用组织结构分类Classification According to Grain Structure用含碳量分类–即低碳钢、中碳钢及高碳钢Classification According to Carbon Contains弹簧用碳钢片CarbonSteel Strip For Spring Use冷轧状态Cold Rolled Strip回火状态Annealed Strip淬火及回火状态Hardened & Tempered Strip/ Precision – Quenched Steel Strip贝氏体钢片Bainite Steel Strip弹簧用碳钢片材之边缘处理Edge Finished淬火剂Quenching Media碳钢回火Tempering回火有低温回火及高温回火Low & High Temperature Tempering高温回火High Temperature Tempering退火Annealing完全退火Full Annealing扩散退火Diffusion Annealing低温退火Low Temperature Annealing中途退火Process Annealing球化退火Spheroidizing Annealing光辉退火Bright Annealing淬火Quenching时间淬火Time Quenching奥氏铁孻回火Austempering马氏铁体淬火Marquenching高碳钢片用途End Usage of High Carbon Steel Strip冷轧高碳钢–日本工业标准Cold-Rolled (Special Steel) Carbon Steel Strip to JIS G3311 电镀金属钢片Plate Metal Strip简介General电镀金属捆片的优点Advantage of Using Plate Metal Strip金属捆片电镀层Plated Layer of Plated Metal Strip镀镍Nickel Plated镀铬Chrome Plated镀黄铜Brass Plated基层金属Base Metal of Plated Metal Strip低碳钢或铁基层金属Iron & Low Carbon as Base Metal不锈钢基层金属Stainless Steel as Base Metal铜基层金属Copper as Base Metal黄铜基层金属Brass as Base Metal轴承合金Bearing Alloy。
模具英语专业术语
模具英语专业术语模具英语专业术语模具的分类:冲压模(五金模): stamping die分离模: cutting die成形模: forming die塑胶模: plastics mold注射模: injection mold压缩模: compression mold铸塑模: transfer mold吹塑模: blow mold吸塑模: suck mold铸造模: casting die砂型铸造: sand casting压铸模: die casting锻造模: forging die塑胶模具术语一、入水：gate进入位(入水点)：gate location水口形式：gate type大水口(侧浇口): edge gate潜水口: sub-gate薄膜式水口: film gate牛角式潜水口: banana gate扇形水口: fan gate环形水口: ring gate二次水口:细水口：pin-point gate水口大小：gate size转水口：switching runner/gate唧嘴口径：sprue diameter直接水口: direct gate二、流道: runner热流道：hot runner,hot manifold热嘴冷流道: hot sprue/cold runner唧嘴直流: direct sprue gate圆形(整圆/半圆)流道：round(full/half) runner矩形流道: rectangle runner梯形流道: trapezoid runnerU形流道: U shape runner流道电脑分析(模流分析)：mold flow analysis流道平衡: runner balance热嘴：hot sprue/tip热流道板：hot manifold发热管：cartridge heater探针: thermocouples插头：connector plug插座：connector socket密封/封料：seal三、运水：water line喉塞：line plug喉管：tube塑胶管：plastic tube快速接头：jiffy quick connector plug/socket 四、模具零件：mold components 三板模(细水口模)：3-plate mold二板模(大水口模)：2-plate mold热流道模具: hot-runner/manifold mold叠层模: stacked mold边钉/导边：leader pin/guide pin边司/导套：guide pin/guide bushing直导套：shoulder guide bushing有托导套：straight guide bushing中托司：ejector guide bush中托边：ejector guide pin回针: return pin面板: top clamp plateA板: A plate推板：stripper plateB板: B plate托板：support plate方铁: spacer block加高方铁: higher spacer block顶针固定板：ejector retainner plate顶针板：ejector plate底板: bottom clamp plate螺丝：screw杯头螺丝: socket cup head screw平头螺丝: socket flat head screw机米螺丝:外六角头螺丝: bolt栓打螺丝(等高螺丝)：S.H.S.B管钉：dowel pin开模槽：ply bar socket内模管位(模仁互锁)：core/cavity inter-lock顶针：ejector pin司筒：ejector sleeve司筒针：sleeve ejector pin缩呵：movable core,return core, core puller 扣机（尼龙拉勾）：nylon latch lock斜顶：lifter模胚（架）：mold base上内模：cavity insert下内模：core insert行位（滑块）：slide行位扣:镶件：insert压座/斜鸡：wedge耐磨板/油板：wear plate压条：gib撑头: support pillar唧嘴：sprue bushing挡板：stop plate定位圈(法兰)：locating ring锁扣(模锁)：latch扣鸡：parting lock set推杆：push bar顶板：eracuretun活动臂：lever arm分流锥：spure sperader水口司:bush垃圾钉：stop pin隔片：buffle弹弓柱：spring rod弹弓:die spring型腔(前模仁): cavity型芯(后模仁): core镶针：insert pin销子(销钉)：dowel pin波子弹弓：ball catch喉塞(堵头): pipe plug锁模块：lock plate斜顶杆：angle ejector rod斜顶针：angle from pin尼龙拉勾：parting locks活动臂：lever arm复位键、提前回杆：early return bar气阀：valves斜导边(斜导柱)：angle pin油缸: hydraulic cylinder液压马达: hydraulic motor齿轮: gear轴承: bear术语：terms承压平面平衡：parting surface support balance分模面排气：parting line venting回针碰料位：return pin and cavity interference模总高超出啤机规格：mold base shut hight顶针碰运水：water line interferes with ejector pin料位出上/下模：part from cavity (core) side模胚原身出料位：cavity direct cut on A-plate,core direct cut on B-plate. 不准用镶件：Do not use (core/cavity) insert用铍铜做镶件：use beryllium copper insert初步模图设计：preliminary mold design正式模图设计：final mold design反呵：reverse core弹弓压缩量：spring compressed length稳定性好：good stability,stable强度不够：insufficient rigidity均匀冷却：even cooling扣模(粘模)：sticking顶白: stress mark热膨胀：thero expansion缩水: shrinkage物料表: BOM原料: raw materials物料: materials工程试模材料: material for engineering mold testing成品: finished product半成品: semi-finished product公差：tolorance铜公(电极)：copper electrode射料不足: short shot缺口: nick瑕疪(斑点): speck亮斑: shine银纹: splay焦痕: gas mark起鳞: delamination冷块: cold slug导色: blush沟槽;凿槽: gouge段面咬花: satin texture证示线: witness line专利: patent沙砾: grit细粒: granule=peuet=grain抽粒机: grit maker缓冲: cushion不锈钢: stainless steel镁铝合金: magnalium镁金属: magnesium钣金: metal plate车/车床: lathe铣床/铣床: mill刨/刨床: plane磨/磨床: grind钻/钻床: drill镗: boring气泡: blinster版次: revision备注: remark生产确认: production control confirmation 初审: checked by核准: approved by部门: department电镀: plate成型: molding样品: sample雕刻: engrave蚀纹: texture加硬: harden热处理: heat treatment淬火: quenching回火: tempering退火: annealing碳化: carbonization铬酸处理: chromate阳性处理: anodize氮化: nitrifying。
最新1 压铸专业英语
1压铸专业英语模具技术用语各种模具常用成形方式accurate die casting 精密压铸 powder forming 粉末成形calendaring molding 压延成形 powder metal forging 粉末锻造cold chamber die casting 冷式压铸 precision forging 精密锻造cold forging 冷锻 press forging 冲锻compacting molding 粉末压出成形 rocking die forging 摇动锻造compound molding 复合成形 rotary forging 回转锻造compression molding 压缩成形 rotational molding 离心成形dip mold 浸渍成形 rubber molding 橡胶成形encapsulation molding 注入成形 sand mold casting 砂模铸造extrusion molding 挤出成形 shell casting 壳模铸造foam forming 发泡成形 sinter forging 烧结锻造forging roll 轧锻 six sides forging 六面锻造gravity casting 重力铸造 slush molding 凝塑成形hollow(blow) molding 中空(吹出)成形 squeeze casting 高压铸造hot chamber die casting 热室压铸 swaging 挤锻hot forging 热锻 transfer molding 转送成形injection molding 射出成形 warm forging 温锻investment casting 精密铸造 matched die method 对模成形法laminating method 被覆淋膜成形 low pressure casting 低压铸造lost wax casting 脱蜡铸造 matched mould thermal forming 对模热成形模各式模具分类用语bismuth mold 铋铸模 landed plunger mold 有肩柱塞式模具burnishing die 挤光模 landed positive mold 有肩全压式模具button die 镶入式圆形凹模 loading shoe mold 料套式模具center-gated mold 中心浇口式模具 loose detail mold 活零件模具chill mold 冷硬用铸模 loose mold 活动式模具clod hobbing 冷挤压制模 louvering die 百叶窗冲切模composite dies 复合模具 manifold die 分歧管模具counter punch 反凸模 modular mold 组合式模具double stack mold 双层模具 multi-cavity mold 多模穴模具electroformed mold 电铸成形模 multi-gate mold 复式浇口模具expander die 扩径模 offswt bending die 双折冷弯模具extrusion die 挤出模 palletizing die 迭层模family mold 反套制品模具 plaster mold 石膏模blank through dies 漏件式落料模 porous mold 通气性模具duplicated cavity plate 复板模 positive mold 全压式模具fantail die 扇尾形模具 pressure die 压紧模fishtail die 鱼尾形模具 profile die 轮廓模flash mold 溢料式模具 progressive die 顺序模gypsum mold 石膏铸模 protable mold 手提式模具hot-runner mold 热流道模具 prototype mold 雏形试验模具ingot mold 钢锭模 punching die 落料模lancing die 切口模 raising(embossing) 压花起伏成形re-entrant mold 倒角式模具 sectional die 拼合模runless injection mold 无流道冷料模具 sectional die 对合模具segment mold 组合模 semi-positive mold 半全压式模具shaper 定型模套 single cavity mold 单腔模具solid forging die 整体锻模 split forging die 拼合锻模split mold 双并式模具 sprueless mold 无注道残料模具squeezing die 挤压模 stretch form die 拉伸成形模sweeping mold 平刮铸模 swing die 振动模具three plates mold 三片式模具 trimming die 切边模unit mold 单元式模具 universal mold 通用模具unscrewing mold 退扣式模具 yoke type die 轭型模模具厂常用之标准零配件air vent vale 通气阀 anchor pin 锚梢angular pin 角梢 baffle 调节阻板angular pin 倾斜梢 baffle plate 折流檔板ball button 球塞套 ball plunger 定位球塞ball slider 球塞滑块 binder plate 压板blank holder 防皱压板 blanking die 落料冲头bolster 上下模板 bottom board 浇注底板bolster 垫板 bottom plate 下固定板bracket 扥架 bumper block 缓冲块buster 堵口 casting ladle 浇注包casting lug 铸耳 cavity 模穴(模仁)cavity retainer plate 模穴扥板 center pin 中心梢clamping block 锁定块 coil spring 螺旋弹簧cold punched nut 冷冲螺母 cooling spiral 螺旋冷却栓core 心型 core pin 心型梢cotter 开口梢 cross 十字接头cushion pin 缓冲梢 diaphragm gate 盘形浇口die approach 模头料道 die bed 型底die block 块形模体 die body 铸模座die bush 合模衬套 die button 冲模母模die clamper 夹模器 die fastener 模具固定用零件die holder 母模固定板 die lip 模唇die plate 冲模板 die set 冲压模座direct gate 直接浇口 dog chuck 爪牙夹头dowel 定位梢 dowel hole 导套孔dowel pin 合模梢 dozzle 辅助浇口dowel pin 定位梢 draft 拔模锥度draw bead 张力调整杆 drive bearing 传动轴承ejection pad 顶出衬垫 ejector 脱模器ejector guide pin 顶出导梢 ejector leader busher 顶出导梢衬套ejector pad 顶出垫 ejector pin 顶出梢ejector plate 顶出板 ejector rod 顶出杆ejector sleeve 顶出衬套 ejector valve 顶出阀eye bolt 环首螺栓 filling core 椿入蕊film gate 薄膜形浇口 finger pin 指形梢finish machined plate 角形模板 finish machined round plate 圆形模板fixed bolster plate 固定侧模板 flanged pin 带凸缘销flash gate 毛边形浇口 flask 上箱floating punch 浮动冲头 gate 浇口gate land 浇口面 gib 凹形拉紧销goose neck 鹅颈管 guide bushing 引导衬套guide pin 导梢 guide post 引导柱guide plate 导板 guide rail 导轨head punch 顶镦冲头 headless punch 直柄冲头heavily tapered solid 整体模蕊盒 hose nippler 管接头impact damper 缓冲器 injection ram 压射柱塞inlay busher 嵌入衬套 inner plunger 内柱塞inner punch 内冲头 insert 嵌件insert pin 嵌件梢 king pin 转向梢king pin bush 主梢襯套 knockout bar 脫模杵land 合模平坦面 land area 合模面leader busher 导梢衬套 lifting pin 起模顶销lining 内衬 locating center punch 定位中心冲头locating pilot pin 定位导梢 locating ring 定位环lock block 压块 locking block 定位块locking plate 定位板 loose bush 活动衬套making die 打印冲子 manifold block 歧管档块master plate 靠模样板 match plate 分型板mold base 塑料模座 mold clamp 铸模紧固夹mold platen 模用板 moving bolster 换模保持装置moving bolster plate 可动侧模板 one piece casting 整体铸件parallel block 平行垫块 paring line 分模线parting lock set 合模定位器 pass guide 穴型导板peened head punch 镶入式冲头 pilot pin 导销pin gate 针尖浇口 plate 衬板pre extrusion punch 顶挤冲头 punch 冲头puncher 推杆 pusher pin 衬套梢rack 机架 rapping rod 起模杆re-entrant mold 凹入模 retainer pin 嵌件梢retainer plate 扥料板 return pin 回位梢riding stripper 浮动脱模器 ring gate 环型浇口roller 滚筒 runner 流道runner ejector set 流道顶出器 runner lock pin 流道拉梢screw plug 头塞 set screw 固定螺丝shedder 脱模装置 shim 分隔片shoe 模座之上下模板 shoot 流道shoulder bolt 肩部螺丝 skeleton 骨架slag riser 冒渣口 slide(slide core) 滑块slip joint 滑配接头 spacer block 间隔块spacer ring 间隔环 spider 模蕊支架spindle 主轴 sprue 注道sprue bushing 注道衬套 sprue bushing guide 注道导套sprue lock bushing 注道定位衬套 sprue puller 注道拉料销spue line 合模线 square key 方键square nut 方螺帽 square thread 方螺纹stop collar 限位套 stop pin 止动梢stop ring 止动环 stopper 定位停止梢straight pin 圆柱销 stripper bolt 脱料螺栓stripper bushing 脱模衬套 stripper plate 剥料板stroke end block 行程止梢 submarine gate 潜入式浇口support pillar 支撑支柱/顶出支柱 support pin 支撑梢supporting plate 扥板 sweep templete 造模刮板tab gate 辅助浇口 taper key 推拔键taper pin 拔锥梢/锥形梢 teeming 浇注three start screw 三条螺纹 thrust pin 推力销tie bar 拉杵 tunnel gate 隧道形浇口vent 通气孔 wortle plate 拉丝模板模具常用之工作机械3D coordinate measurement 三次元量床 boring machine 搪孔机cnc milling machine CNC铣床 contouring machine 轮廓锯床copy grinding machine 仿形磨床 copy lathe 仿形车床copy milling machine 仿形铣床 copy shaping machine 仿形刨床cylindrical grinding machine 外圆磨床 die spotting machine 合模机drilling machine 钻孔机 engraving machine 雕刻机engraving E.D.M. 雕模放置加工机 form grinding machine 成形磨床graphite machine 石墨加工机 horizontal boring machine 卧式搪孔机horizontal machine center 卧式加工制造中心 internal cylindrical machine 内圆磨床jig boring machine 冶具搪孔机 jig grinding machine 冶具磨床lap machine 研磨机 machine center 加工制造中心multi model miller 靠磨铣床 NC drilling machine NC钻床NC grinding machine NC磨床 NC lathe NC车床NC programming system NC程序制作系统 planer 龙门刨床profile grinding machine 投影磨床 projection grinder 投影磨床radial drilling machine 旋臂钻床 shaper 牛头刨床surface grinder 平面磨床 try machine 试模机turret lathe 转塔车床 universal tool grinding machine 万能工具磨床vertical machine center 立式加工制造中心 wire E.D.M. 线割放电加工机检验量测工具用语autocollimator 自动准直机 bench comparator 比长仪block gauge 块规 bore check 精密小测定器calibration 校准 caliper gauge 卡规check gauge 校对规 clearance gauge 间隙规clinoretee 测斜仪 comparator 比测仪cylinder square 圆筒直尺 depth gauge 测深规dial indicator 针盘指示表 dial snap gauge 卡规digital micrometer 数位式测微计 feeler gauge 测隙规gauge plate 量规定位板 height gauge 测高规inside calipers 内卡钳 inside micrometer 内分厘卡interferometer 干涉仪 leveling block 平台limit gauge 限规 micrometer 测微计mil 千分之一吋 monometer 压力计morse taper gauge 莫氏锥度量规 nonius 游标卡尺optical flat 光学平晶 optical parallel 光学平行passimeter 内径仪 position scale 位置刻度profile projector 轮廓光学投影仪 protractor 分角器radius 半径 ring gauge 环规sine bar 正弦量规 snap gauge 卡模square master 直角尺 stylus 触针telescopic gauge 伸缩性量规 working gauge 工作量规模具钢材alloy tool steel 合金工具钢 aluminium alloy 铝合金钢bearing alloy 轴承合金 blister steel 浸碳钢bonderized steel sheet 邦德防蚀钢板 carbon tool steel 碳素工具钢clad sheet 被覆板 clod work die steel 冷锻模用钢emery 金钢砂 ferrostatic pressure 钢铁水静压力forging die steel 锻造模用钢 galvanized steel sheet 镀锌铁板hard alloy steel 超硬合金钢 high speed tool steel 高速度工具钢hot work die steel 热锻模用钢 low alloy tool steel 特殊工具钢low manganese casting steel 低锰铸钢 marging steel 马式体高强度热处理钢martrix alloy 马特里斯合金 meehanite cast iron 米汉纳铸钢meehanite metal 米汉纳铁 merchant iron 市售钢材molybdenum high speed steel 钼系高速钢 molybdenum steel 钼钢nickel chromium steel 镍铬钢 prehardened steel 顶硬钢silicon steel sheet 硅钢板 stainless steel 不锈钢tin plated steel sheet 镀锡铁板 tough pitch copper 韧铜troostite 吐粒散铁 tungsten steel 钨钢vinyl tapped steel sheet 塑料覆面钢板表面处理关连用语age hardening 时效硬化 ageing 老化处理air hardening 气体硬化 air patenting 空气韧化annealing 退火 anode effect 阳极效应anodizing 阳极氧化处理 atomloy treatment 阿扥木洛伊表面austempering 奥氏体等温淬火 austenite 奥斯田体/奥氏体bainite 贝氏体 banded structure 条纹状组织barrel plating 滚镀 barrel tumbling 滚筒打光blackening 染黑法 blue shortness 青熟脆性bonderizing 磷酸盐皮膜处理 box annealing 箱型退火box carburizing 封箱渗碳 bright electroplating 辉面电镀bright heat treatment 光辉热处理 bypass heat treatment 旁路热处理carbide 炭化物 carburized case depth 浸碳硬化深层carburizing 渗碳 cementite 炭化铁chemical plating 化学电镀 chemical vapor deposition 化学蒸镀coarsening 结晶粒粗大化 coating 涂布被覆cold shortness 低温脆性 comemtite 渗碳体controlled atmosphere 大气热处理 corner effect 锐角效应creeping discharge 蠕缓放电 decarburization 脱碳处理decarburizing 脱碳退火 depth of hardening 硬化深层diffusion 扩散 diffusion annealing 扩散退火electrolytic hardening 电解淬火 embossing 压花etching 表面蚀刻 ferrite 肥粒铁first stage annealing 第一段退火 flame hardening 火焰硬化flame treatment 火焰处理 full annealing 完全退火gaseous cyaniding 气体氧化法 globular cementite 球状炭化铁grain size 结晶粒度 granolite treatment 磷酸溶液热处理graphitizing 石墨退火 hardenability 硬化性hardenability curve 硬化性曲线 hardening 硬化heat treatment 热处理 hot bath quenching 热浴淬火hot dipping 热浸镀 induction hardening 高周波硬化ion carbonitriding 离子渗碳氮化 ion carburizing 离子渗碳处理ion plating 离子电镀 isothermal annealing 等温退火liquid honing 液体喷砂法 low temperature annealing 低温退火malleablizing 可锻化退火 martempering 麻回火处理martensite 马氏体/硬化铁炭 metallikon 金属喷镀法metallizing 真空涂膜 nitriding 氮化处理nitrocarburizing 软氮化 normalizing 正常化oil quenching 油淬化 overageing 过老化overheating 过热 pearlite 针尖组织phosphating 磷酸盐皮膜处理 physical vapor deposition 物理蒸镀plasma nitriding 离子氮化 pre-annealing 预备退火precipitation 析出 precipitation hardening 析出硬化press quenching 加压硬化 process annealing 制程退火quench ageing 淬火老化 quench hardening 淬火quenching crack 淬火裂痕 quenching distortion 淬火变形quenching stress 淬火应力 reconditioning 再调质recrystallization 再结晶 red shortness 红热脆性residual stress 残留应力 retained austenite 残留奥rust prevention 防蚀 salt bath quenching 盐浴淬火sand blast 喷砂处理 seasoning 时效处理second stage annealing 第二段退火 secular distortion 经年变形segregation 偏析 selective hardening 部分淬火shot blast 喷丸处理 shot peening 珠击法single stage nitriding 等温渗氮 sintering 烧结处理soaking 均热处理 softening 软化退火solution treatment 固溶化热处理 spheroidizing 球状化退火stabilizing treatment 安定化处理 straightening annealing 矫直退火strain ageing 应变老化 stress relieving annealing 应力消除退火subzero treatment 生冷处理 supercooling 过冷surface hardening 表面硬化处理 temper brittleness 回火脆性temper colour 回火颜色 tempering 回火tempering crack 回火裂痕 texture 咬花thermal refining 调质处理 thermoechanical treatment 加工热处理time quenching 时间淬火 transformation 变态tufftride process 软氮化处理 under annealing 不完全退火vacuum carbonitriding 真空渗碳氮化 vacuum carburizing 真空渗碳处理vacuum hardening 真空淬火 vacuum heat treatment 真空热处理vacuum nitriding 真空氮化 water quenching 水淬火wetout 浸润处理焊接用语acetylene 乙炔 ampere 电流安培angle welding 角焊 arc 电弧argon arc welding 氩弧焊接 bare electrode 光熔接条butt welding 对接焊接 camber 电弧弯曲cascade 阶迭熔接法 clad weld 被覆熔接crator 焊疤 excess metal 多余金属filler rod 焊条 fillet weld 填角焊接gas shield 气体遮蔽 groove welding 起槽熔接hand face shield 手握面罩 hard facing 硬表面堆焊jig welding 工模焊接 laser beam welding 雷射光焊接metal electrode insert gas welding MIG熔接 nugget 点焊熔核overlaying 堆焊 peening of welding 珠击熔接法plug welding 塞孔熔接 positioned welding 正向熔接pressure welding 压焊 propane gas cutting 丙烷气切割pure nickel electrode 纯镍熔接条 reinforcement of weld 加强焊接resist 抗蚀护膜 root running 背面熔接seam 焊缝 seaming 接合seam welding 流缝熔接 series seam welding 串联缝熔接skip welding process 跳焊法 spark 火花spot welding 点焊接 stitch welding 针角焊接stud arc welding 电弧焊接 under laying 下部焊层void 焊接空隙 weld flow mark 焊接流痕weld flush 焊缝凸起 weld line 焊接纹weld mark 焊接痕 weld penetration 熔接透入weld zone 焊接区 welding 焊接welding bead 焊接泡 welding direction 焊接方向welding distortion 焊接变形 welding flux 焊剂welding ground 电熔接地 welding interval 焊接周期welding stress 熔接应变 welding torch 熔接气炬射出成形关联用语activator 活化剂 bag moulding 气胎施压成形bonding strength 黏合强度 breathing 排气caulking compound 填隙料 cell 气孔cold slug 半凝式射出 colorant 着色剂color matching 调色 color masterbatch 色母料compound 混合料 copolymer 共聚合体cull 残料废品 cure 凝固化cryptometer 不透明度儀 daylight 開隙dry cycle time 空料試車週期時間 ductility 延性elastomer 弹性体 extruded bead sealing 压出粒涂层法feed 供料 filler 充填剂film blowing 薄膜吹制法 floating platen 活动模板foaming agent 发泡剂 gloss 光泽granule 颗粒料 gunk 料斗hot mark 热斑 hot stamping 烫印injection nozzle 射出喷嘴 injection plunger 射出柱塞injection ram 射出冲柱 isomer 同分异构物kneader 混合机 leveling agent 匀涂剂lubricant 润滑剂 matched die method 配合成形法mould clamping force 锁模力 mould release agent 脱模剂nozzle 喷嘴 oriented film 取向薄膜parison 吹气成形坏料 pellet 粒料plasticizer 可塑剂 plunger 压料柱塞porosity 孔隙率 post cure 后固化premix 预混料 purging 清除reciprocating screw 往复螺杆 resilience 回弹性resin injection 树脂射出法 rheology 流变学sheet 塑料片 shot 注射shot cycle 射出循环 slip agent 光滑剂take out device 取料装置 tie bar 拉杆toggle type mould clamping system 肘杆式锁模装置torpedo spreader 鱼雷形分流板 transparency 透明性void content 空洞率塑料原料acrylic 压克力 casein 酪素cellulose acetate 醋酸纤维素CA cellulose acetate butyrate 醋酸丁酸纤维素CABcomposite material 复合材料 cresol resin 甲酚树脂CFdially phthalate 苯二甲酸二烯丙酯 disperse reinforcement 分散性强化复合材料engineering plastics 工程塑料 epoxy resin 环氧树脂EPethyl cellulose 乙基纤维素 ethylene vinylacetate copolymer 乙烯-醋酸乙烯EVAethylene-vinlacetate copolyme 醋酸乙烯共聚物EVA expanded polystyrene 发泡聚苯乙烯EPS fiber reinforcement 纤维强化热固性/纤维强化复合材料high density polyethylene 高密度聚乙烯HDPEhigh impact polystyrene 高冲击聚苯乙烯HIPShigh impact polystyrene rigidity 高冲击性聚苯乙烯low density polyethylene 低密度聚乙烯LDPE melamine resin 三聚氰胺酚醛树脂MFnitrocellulose 硝酸纤维素 phenolic resin 酚醛树脂plastic 塑料 polyacrylic acid 聚丙烯酸PAPpolyamide 耐龙PA polybutyleneterephthalate 聚对苯二甲酸丁酯PBTpolycarbonate 聚碳酸酯PC polyethyleneglycol 聚乙二醇PFGpolyethyleneoxide 聚氧化乙烯PEO polyethyleneterephthalate 聚乙醇对苯PETP polymetylmethacrylate 聚甲基丙烯酸甲酯PMMA polyoxymethylene 聚缩醛POMpolyphenylene oxide 聚硫化亚苯 polyphenyleneoxide 聚苯醚PPOpolypropylene 聚丙烯PP polystyrene 聚苯乙烯PSpolytetrafluoroethylene 聚四氟乙烯PTFE polytetrafluoroethylene 聚四氟乙烯polythene 聚乙烯PE polyurethane 聚氨基甲酸酯PUpolyvinylacetate 聚醋酸乙烯PVAC polyvinylalcohol 聚乙烯醇PVApolyvinylbutyral 聚乙烯醇缩丁醛PVB polyvinylchloride 聚氯乙烯PVCpolyvinylfuoride 聚氟乙烯PVF polyvinylidenechloride 聚偏二氯乙烯PVDCprepolymer 预聚物 silicone resin 硅树脂thermoplastic 热塑性 thermosetting 热固性thermosetting plastic 塑料 unsaturated polyester 不饱和聚酯树脂成形不良用语aberration 色差 atomization 霚化bank mark 滞料纹 bite 咬入blacking hole 涂料孔(铸疵) blacking scab 涂料疤blister 起泡 blooming 起霜blow hole 破孔 blushing 泛白body wrinkle 侧壁皱纹 breaking-in 冒口带肉bubble 膜泡 burn mark 糊斑burr 毛边 camber 翘曲cell 气泡 center buckle 表面中部波皱check 细裂痕 checking 龟裂chipping 修整表面缺陷 clamp-off 铸件凹痕collapse 塌陷 color mottle 色斑corrosion 腐蚀 crack 裂痕crazing 碎裂 crazing 龟裂deformation 变形 edge 切边碎片edge crack 裂边 fading 退色filler speak 填充料斑 fissure 裂纹flange wrinkle 凸缘起皱 flaw 刮伤flow mark 流痕 galling 毛边glazing 光滑 gloss 光泽grease pits 污斑 grinding defect 磨痕haircrack 发裂 haze 雾度incrustation 水锈 indentation 压痕internal porosity 内部气孔 mismatch 偏模mottle 斑点 necking 缩颈nick 割痕 orange peel 橘皮状表面缺陷overflow 溢流 peeling 剥离pit 坑 pitting corrosion 点状腐蚀plate mark 模板印痕 pock 麻点pock mark 痘斑 resin streak 树脂流纹resin wear 树脂脱落 riding 凹陷sagging 松垂 saponification 皂化scar 疤痕 scrap 废料scrap jam 废料阻塞 scratch 刮伤/划痕scuffing 深冲表面划伤 seam 裂痕shock line 模口挤痕 short shot 充填不足shrinkage pool 凹孔 sink mark 凹痕skin inclusion 表皮折迭 straightening 矫直streak 条状痕 surface check 表面裂痕surface roughening 橘皮状表皮皱折 surging 波动sweat out 冒汗 torsion 扭曲warpage 翘曲 waviness 波痕webbing 熔塌 weld mark 焊痕whitening 白化 wrinkle 皱纹模具常用刀具与工作法用语adjustable spanner 活动扳手 angle cutter 角铣刀anvil 铁钻 arbour 心轴backing 衬垫 belt sander 带式打磨机buffing 抛光 chamfering machine 倒角机chamfering tool 去角刀具 chisel 扁錾chuck 夹具 compass 两角规concave cutter 凹面铣刀 convex cutter 凸形铣刀cross joint 十字接头 cutting edge clearance 刃口余隙角drill stand 钻台 edge file 刃用锉刀file 锉刀 flange joint 凸缘接头grinder 砂轮机 hammer 铁锤hand brace 手摇钻 hatching 剖面线hexagon headed bolt 六角头螺栓 hexagon nut 六角螺帽index head 分度头 jack 千斤顶jig 治具 kit 工具箱lapping 研磨 metal saw 金工锯nose angle 刀角 pinchers 钳子pliers 铗钳 plug 柱塞头polisher 磨光器 protable driller 手提钻孔机punch 冲头 sand paper 砂纸scraper 刮刀 screw driver 螺丝起子scribing 划线 second out file 中纹锉spanner 扳手 spline broach 方栓槽拉刀square 直角尺 square sleeker 方形镘刀square trowel 直角度 stripping 剥离工具T-slot T形槽 tool for lathe 车刀tool point angle 刀刃角 tool post 刀架tosecan 划线盘 trimming 去毛边waffle die flattening 压纹效平 wiper 脱模钳wrench 螺旋扳手计算机关联用语3D modeling 三次元模拟 access 通路animation 卡通影片 application 应用board 基板 bug 故障bus 总线 CAD 计算机辅助设计CAE 计算机辅助工程分析 CAM 计算机辅助制造cassette 卡座 color display 彩色显示器command 指令 communication 通信compact 精简小型 computer 计算机copy 复制 cursor 游标curve modeling 曲面仿真 database 数据库design 设计 digitizing 数字化disk 磁盘 dot 点eyelet 眼孔 floppy 磁盘片format 格式化 graphic 圆解hardware 硬件 honeycomb 蜂巢interface 界面 know how 秘诀laser printer 激光打印机 lay out 布置memory 记忆 memory swap 交换记忆microprocessor 微处理器 modeling 造型module 模块 monitor 屏幕mouse 鼠标 need 需求network 网络 new version 新版on line 上线中 option 选择PC 个人计算机 plotter 绘图机program 程序 scanning 扫描simulation 仿真 software 软件solid model 实体模型 system 系统tape 磁带 terminal 终端机texture 构造 trim 修边venter 排气风扇 word processor 文书处理器各种冲模加工关连用语barreling 滚光加工 belling 压凸加工bending 弯曲加工 blanking 下料加工bulging 撑压加工 burring 冲缘加工cam die bending 凸轮弯曲加工 caulking 铆合加工coining 压印加工 compressing 压缩加工compression bending 押弯曲加工 crowning 凸面加工curl bending 卷边弯曲加工 curling 卷曲加工cutting 切削加工 dinking 切断蕊骨double shearing 迭板裁断 drawing 引伸加工drawing with ironing 抽引光滑加工 embossing 浮花压制加工extrusion 挤制加工 filing 锉削加工fine blanking 精密下料加工 finish blanking 光制下料加工finishing 精整加工 flanging 凸缘加工folding 折边弯曲加工 folding 折迭加工forming 成形加工 impact extrusion 冲击挤压加工indenting 压痕加工 ironing 引缩加工knurling 滚花 lock seaming 固定接合louvering 百叶窗板加工 marking 刻印加工necking 颈缩加工 notching 冲口加工parting 分断加工 piercing 冲孔加工progressive bending 连续弯曲加工 progressive blanking 连续下料加工progressive drawing 连续引伸加工 progressive forming 连续成形加工reaming 铰孔加工 restriking 二次精冲加工riveting 铆接加工 roll bending 滚筒弯曲加工roll finishing 滚压加工 rolling 压延加工roughing 粗加工 scrapless machining 无废料加工seaming 折弯重迭加工 shaving 缺口修整加工shearing 切断加工 sizing 精压加工/矫正加工slitting 割缝加工 spinning 卷边铆接staking 铆固 stamping 锻压加工swaging 挤锻压加工 trimming 整缘加工upsetting 锻粗加工 wiring 抽线加工冲压机械及周边关连用语back shaft 支撑轴 blank determination 胚料展开bottom slide press 下传动式压力机 board drop hammer 板落锤brake 煞车 buckle 剥砂面camlachie cramp 铸包 casting on flat 铆合chamotte sand 烧磨砂 charging hopper 加料漏斗clearance 间隙 closed-die forging 合模锻造clump 夹紧 clutch 离合器clutch brake 离合器制动器 clutch boss 离合器轮壳clutch lining 离合器覆盖 coil car 带卷升降运输机coil cradle 卷材进料装置 coil reel stand 钢材卷料架column 圆柱 connection screw 连杆调节螺钉core compound 砂心黏结剂 counter blow hammer 对击锻锤cradle 送料架 crank 曲柄轴crankless 无曲柄式 cross crank 横向曲轴cushion 缓冲 depression 外缩凹孔dial feed 分度送料 die approach 模口角度die assembly 合模 die cushion 模具缓冲垫die height 冲压闭合高度 die life 模具寿命die opening 母模逃孔 die spotting press 调整冲模用压力机double crank press 双曲柄轴冲床 draght angle 逃料倾斜角edging 边锻伸 embedded core 加装砂心feed length 送料长度 feed level 送料高度filling core 埋入砂心 filling in 填砂film play 液面花纹 fine blanking press 精密下料冲床forging roll 辊锻机 finishing slag 炼后熔渣fly wheel 飞轮 fly wheel brake 飞轮制动器foot press 脚踏冲床 formboard 进模口板frame 床身机架 friction 摩擦friction brake 摩擦煞车 gap shear 凹口剪床gear 齿轮 gib 滑块引导部gripper 夹具 gripper feed 夹持进料gripper feeder 夹紧传送装置 hammer 槌机hand press 手动冲床 hand rack pinion press 手动齿轮齿条式冲床hand screw press 手动螺旋式冲床 hopper feed 料斗送料idle stage 空站 inching 微调尺寸isothermal forging 恒温锻造 key clutch 键槽离合器knockout 脱模装置 knuckle mechanic 转向机构land 模具直线刀面部 level 水平loader 供料器 unloader 卸料机loop controller 闭回路控制器 lower die 下模micro inching device 微寸动装置 microinching equipment 微动装置motor 马达 moving bolster 活动工作台notching press 冲缺口压力机 opening 排料逃孔overload protection device 防超载装置 pinch roll 导正滚轮pinion 小齿轮 pitch 节距pressfit 压入 progressive 连续送料pusher feed 推杆式送料 pusher feeder 料片押片装置quick die change system 快速换模系统 regrinding 再次研磨releasing 松释动作 reversed blanking 反转下料robot 机器人 roll forming machine 辊轧成形roll forming machine 辊轧成形机 roll release 脱辊roller feed 辊式送料 roller leveler 辊式矫直机rotary bender 卷弯成形机 safety guard 安全保护装置scrap cutter 废料切刀 scrap press 废料冲床seamless forging 无缝锻造 separate 分离shave 崩砂 shear angle 剪角sheet loader 薄板装料机 shot 单行程工作shrinkage fit 收缩配合 shut height 闭合高度sieve mesh 筛孔 sintering of sand 铸砂烧贴slide balancer 滑动平衡器 slug hole 逃料孔spin forming machine 旋压成形机 spotting 合模stack feeder 堆栈拨送料机 stickness 黏模性straight side frame 冲床侧板 stretcher leveler 拉伸矫直机strip feeder 料材送料装置 stripping pressure 弹出压力stroke 冲程 take out device 取料装置toggle press 肘杆式压力机 transfer 传送transfer feed 连续自动送料装置 turrent punch press 转塔冲床two speed clutch 双速离合器 uncoiler 闭卷送料机unloader 卸载机 vibration feeder 振动送料机wiring press 嵌线卷边机线切割放电加工关连用语abnormal glow 不规则辉光放电 arc discharge 电弧放电belt 皮带 centreless 无心chrome bronze 铭铜 clearance angle 后角corner shear drop 直角压陷 deflection 桡曲度discharge energy 放电能量 dressing 修整dwell 保压 flange 凸缘gap 间隙 graphite 石墨graphite contraction allowance 电极缩小余量 graphite holder 电极夹座hair crack 发裂 horn 电极臂jump 跳刀 magnetic base 磁性座master graphite 标准电极 pipe graphite 管状电极pulse 脉冲 rib working 肋部加工roller electrode 滚轮式电极 rotary surface 旋转面shank 柄部 sharp edge 锐角部tough bronze 韧铜 traverse 摇臂tungsten bronze 钨青铜 waviness 波形起伏work 工件 working allowance 加工余量working dischard 加工废料锻铸造关连用语accretion 炉瘤 acid converter 酸性转炉acid lining cupola 酸性熔铁炉 acid open-hearth furnace 酸性平炉aerator 松砂机 air set mold 常温自硬铸模airless blasting cleaning 离心喷光 all core molding 集合式铸模all round die holder 通用模座 assembly mark 铸造合模记号back pouring 补浇注 backing sand 背砂base bullion 粗金属锭 base permeability 原砂透气度belling 压凸 billet 坏料bleed 漏铸 blocker 预锻模膛blocking 粗胚锻件 blow hole 铸件气孔board drop hammer 板落锤 bottom pour mold 底浇bottom pouring 底注 boxless mold 脱箱砂模break-off core 缩颈砂心 brick molding 砌箱造模法buckle 剥砂面 camber 错箱camlachie cramp 铸包 cast blade 铸造叶片casting flange 铸造凸缘 casting on flat 水平铸造chamotte sand 烧磨砂 charging hopper 加料漏斗cleaning of casting 铸件清理 closed-die forging 合模锻造core compound 砂心黏结剂 core template 砂心模板core vent 砂蕊排气孔 corner gate 压边浇口counter blow hammer 对击锻造 counter lock 止口镶嵌方式depression 外缩凹孔 die approach 模口角度draw out 锻造拔长 draw plate 起模板draw spike 起模长针 dummying 预锻embedded core 加装砂心 erosion 冲砂fettling 铸件清理 filling core 埋入砂心filling in 填砂 film play 液面花纹finishing slag 炼后熔渣 flash gutter 锻模飞边槽flask molding 砂箱造模 forging roll 辊锻机formboard 进模口板 gutter 锻模飞边槽hammer man 锻工 heading machine 顶镦机impacter 卧式锻造机 inblock cast 整体铸造ingot 铸锭 ingot blank 铸坯inlay casting 镶铸法 investment casting 失模铸造isothermal forging 恒温锻造 loose piece 木模活块molding pit 铸模地坑 pouring process 浇注法recasting 重铸 roll forging 轧锻rolled surface 轧制表面 rough sand 粗砂roughing forge 粗锻 sand crushing 塌箱seamless forging 无缝锻造 separate 分离shave 崩砂 shrinkage fit 收缩配合shut height 闭合高度 sieve mesh 筛孔sintering of sand 铸砂烧贴 slag 熔渣slag inclusion 夹渣 stickness 黏模性strip layout 带状胚料排样法 tap casting 顶注top gate 顶注浇口 unworked casting 不加工铸件upender 翻转装置 upending 顶锻uphill casting 底铸 white cast iron 白口铸件模具加工方法barrel 滚筒(加工) bending 波纹加工broaching 拉刀切削 centering 定中心cutting 切削 cylindrical lathe cutting 外圆车削electric discharge machine 放电加工 electrolytic grinding 电解研磨embossing 压花加工 facing 面车削filing 锉刀修润 hand finishing 手工修润hemming 卷边加工 hobbing 滚齿加工joggling 摇动加工 lapping 抛光/研磨修润laser beam machining 雷射加工 lathe cutting 车床车削planning 刨削加工 polishing 抛亮光reaming 铰孔修润 rough machining 粗切削rounding 圆形加工 sawing 锯削scaling 清除钢碇缺陷 shaping 成形加工skiving 表面研磨 slotting 切缝切削taper turning 锥度车削 thread cutting 螺纹切削ultrasonic machining 超音波加工 up cut milling 逆铣加工学理实验与试验用语air permeability test 透气性试验 austenitic steel 沃斯田铁钢brinell hardness 布耐内尔硬度 brinell hardness test 布氏硬度试验charpy impact test 夏比冲击试验 conical cup test 圆锥杯突试验cup flow test 杯模式流动度试验 dart drop impact test 落锤冲击试验Elmendorf test 埃罗门多撕裂强度试验 environmental stress cracking test 环境应力龟裂试验ericessen test 埃留伸薄板拉伸试验 falling ball impact test 落球冲击试验fatigue test 疲劳试验 ferrite 纯铁体gantt chart 甘特图 heat cycle test 热循环试验histogram 柱状图 hot bend test 热弯试验izod impact test 埃左德冲击试验 loop tenacity 环结强度martens heat distortion temperature test 马顿斯耐热试验martensite 马氏体 mullen bursting strength tester 密廉式破裂强度试验机nol ring test 诺尔环试验 normal distribution 常态分配ozone resistance test 抗臭氧试验 pareto diagram 柏拉图peeling test 剥离试验 pinhole test 针孔试验机rattler test 磨耗试验 rockweel hardness test 洛氏硬度试验rockweel hardness 洛氏威尔硬度 rolinx process 罗林克斯射出压缩成形法rossi-peakes flow test 罗西皮克斯流动试验 sampling inspection 抽样检查scratch hardness 抗刮硬度 shore hardness 萧氏硬度spiral flow test 螺旋流动试验 surface abrasion test 表面磨耗试验taber abraser 泰伯磨耗试验机 tensile impact test 拉伸冲击试验tensile strength 抗拉强度 tension test 张力试验thermal shock test 冷热剧变试验 torsion test 扭曲试验ubbelohde viscometer 乌别洛德黏度计 vicat indentation test 维卡针压陷试验Vickers hardness test 维氏硬度试验 warpage test 翘曲试验weatherometer 人工老化试验机 weissenberg effect 威森伯格回转效应砂轮用语abrasive 砂轮 Al2O3 氧化铝balance 平衡 bond 结合borazon 氧化硼立方晶 buffing wheel 抛光布轮diamond 钻石 dresser 砂轮整修机dressing 修整 endless grinding belt 循环式研磨带finishing allowance 加工余量 grain 磨粒grinding disc 研磨盘 jamp up 孔眼堵塞mesh 网筛目 parameter 参数resinoid grinding wheel 半树脂型砂轮 slitting 切缝量vitrified 陶瓷的 wheel 旋转机械设计及周边其它用语assembly drawing 装配图 auto tool change cycle 自动换刀时间周期beam 横梁 bending moment 弯矩bending stress 弯曲应力 bottoming 底靠buckling 纵弯曲 chamfering 去角斜切channel 凹槽 chattering 颤动check point 查核点 chip 切屑chip conveyor 排屑输送机 coefficient of friction 摩擦系数compact 小型的 cooling pipe 冷却管coupon 试样胚 deflection 挠曲量distortion 扭曲变形 draft taper 拔模锥度draw out 拉拔 fit tolerance 配合公差flexible rigidity 弯曲刚性 gas vent 气孔hatching 剖面线 heater cooler 加热器冷却装置hook cavity 钩穴 inching 寸动。
铸造专业英语词汇
Abating退火Abrasion磨损Abrasive paper 砂纸Abrasive wheel 砂轮Accessory 附件，活块Acicular ferrite 针状铁素体Acid refractory 酸性耐火材料Acid-proof cast iron / acid-resistance casting/ acid resisting cast iron 耐酸铸件Acid slay 酸性渣Active clay 有效粘土AFS fineness 美国铸造学会型砂粒度Agitator 搅拌机（型砂试验）Agitation 搅拌Air blower 鼓风机Air drain 出气口（浇注系统）Air pollution control 大气污染控制Air tightness 气密性Air vent 出气孔Allowance 余量，津贴，补助，宽容Alloying agent 合金元素Alloying component 合金成分Anti-rust 防锈Argon 氩气Atomization 雾化，喷雾Atomizer test 雾化试验（检验金属表面油脂）Attack 侵蚀Attack polishing method 侵蚀抛光法Automatic charging 自动加料Automatic de-sprueing 自动切除冒口Automatic molding 自动造型Automatic pouring device 自动浇注装置Automatic sand plant 自动化砂处理装置Baked core 干砂芯Balance 天平/余额Ball feeder 球状冒口Ball hardness 布氏硬度Ball hardness testing machine 布氏硬度机Ball mill 球磨机Band/belt conveyer 皮带输送机Band/belt elevator 皮带斗式提升机Bar bend test 试棒抗弯试验Base 底，基础Base line 基线Base plate 底板Base sand 原砂Basic 碱性的，基本的Batch mill / batch sand mixer 混砂机Beader pearlite 珠光体Bed charge/coke 底焦Belt grinder 带式磨光机Bending strength 抗弯强度Bentonite 膨润土Binder 粘结剂Bituminous coal dust/black dust 煤粉Black short 冷脆Black skin 黑皮，铸皮Blank 毛胚，下料Blast 鼓风，送风Blast capacity 风量Blast fan 离心式鼓风机Blast hole 风口Blast intensity 鼓风强度Blast pressure gage 风压表Blast regulator 风量调节器Blast volume 风量Bleed 缺肉，台箱跑火Blender 混砂机，搅拌机Blind feeder/head 暗冒口Blind roaster 马弗炉Blind scab 起痂Blister 皮下气泡Blow down 停炉Boiling point 沸点Bond 粘结剂，合同Bond clay 造型粘土Bond strength 粘结强度Bottom door 炉底们Bottom drop 打炉Breaking-in 带肉Brinell hardness 布氏硬度Brittleness 脆性Brittle fracture 脆性断口，脆性断裂B type graphite B型石墨Buffing 抛光Buffing machine 抛光机Bunker 料斗CE carbon equivalent 碳当量Carbide 碳化物carbon dioxide二氧化碳carbon monoxide 一氧化碳carbon pick-up 增碳carburetter 增碳剂，汽化器case hardening 表面硬化case gate 内浇口casting alloy 铸造合金casting defect/ casting flaw 铸造缺陷casting design 铸造设计casting equipmentcasting ladle 浇包casting lap 铸造冷隔casting leakage 铸造渗漏casting plan 铸造方案casting property 铸造性能casting rate 浇注速度casting skin 铸皮，黑皮casting strain 铸造（内应力）变形casting stress 铸造应力casting surface表皮casting technique 铸造工艺/技术cast integral test bar 单铸试棒caulk 腻缝，抿灰Celsius thermometer 摄氏温度计Cementite 渗碳体，碳化铁Center gate 中心浇口Center line 中心线Chain hoist 手动葫芦Charging 加料Charger 加料机Charging material 炉料/批料Chilled cast iron 冷铁Chill element 促白口元素Chilling action 激冷作用Chilling tendency 白口倾向Chrysanthemum graphite 菊花状石墨Cinder inclusion 夹渣Cinder notch 出渣口Clay washer 洗砂机Clockwise rotation 顺时针方向Clowhole / contraction cavity 锁孔Cold box process 冷芯盒制芯法Cold lap / cold shut 冷隔Collapsibility / lubricate 溃散性Consistency 稠度，浓度，一致性Continuous desulfurization 连续脱硫Contamination 污染Conveyor belt 输送带，传送带Cooling agent 冷却剂Cooling curve 冷却曲线Cooling effect 冷却作用Cooling rate 冷却速度Core 砂芯Core boxCoremaking 制芯Coresetter 下芯机Cover 覆盖剂Cross gate 横浇道Crush 掉砂Cupola 冲天炉Cupola drop 打炉Cupola lining 炉衬Cupola spout 出铁槽Cut-off machine 切割机Damper 减震器Damping capacity / effect 减震能力/效果Datum face / line 基准面/线Deadhead 冒口废料Deburring 打毛刺Defect index 废品率Deformation 变形Density 密度Degreaser 脱脂剂Degree of graphitization 石墨化程度Dimensional stability 尺寸稳定性Descale 除锈，除氧化皮Decaling除锈，除氧化皮Design drawing 设计图Deslag 扒渣Destructive testing/inspection 破坏性试验/检验Desulfuration / desulphurization 脱硫Desulfurizer 脱硫剂Detection 检查，摊伤Die cavity 型腔，模腔Differential hardening / heating / quenching 局部硬化/加热/淬火Diffuse 扩散Dilatant 膨胀Dilute 稀释，冲淡Dimensional error / tolerance 尺寸误差/公差Direction l solidification 顺序凝固，定向凝固Dirt / dirt inclusion 夹渣Disintegration 溃散，崩解，分解Disk feeder 圆盘给料机Dislocation 位错Displacement 位移/置换Dissipation heat 散热Distorted patter 模变形Distortion 变形，扭曲Divorced pearlite 粒状珠光体Down runner / gate / downright 直浇口Ductile iron 球墨铸铁Duff 煤粉Durability 耐用性，耐久性Dust catcher 集尘器elastic deformation 弹性变形Elementary analysis 元素分析Elevator 提升机Elongation 延伸率，延长Endurance 耐用性，持久度Endurance limit 疲劳极限Energy loss 能量损失Environment contamination 环境污染Environmental control 污染控制Equilibrium 平衡Eutectic 共晶体，恭晶的Examination performance / result 考试成绩Fading 衰退Failure stress 破坏应力Feather 毛刺，羽毛Feeding effect 补缩效果Feeding gate 内浇口Feed/feeder head(=riser)/feeding head 冒口Ferric 铁Ferric carbide 渗碳体，碳化铁Ferrite 铁素体Ferromanganese 锰铁Ferromolybdenum 钼铁Ferrosilicon 硅铁Fettle 铲除炉壁渣子File 锉刀Filter paper/screen 滤纸/网Fin 毛刺Final machining 精加工Fine silt 粉尘Finished allowance 加工余量Finished surface 加工面Fire brick 耐火砖Fire cracking 热裂Fire resistance 耐火性Fire waste 烧损Fixture 夹具Flake form 片状Flake graphite 片状石墨Flaking off (=spalling) 剥落Flash point 闪点Flaw detection 探伤Floatation 漂浮Flowability/fluidity 流动性Flow-chart 流程图Fluid contraction 液态收缩Flushing 流渣Fold 冷隔Foreign substance 杂质Forging 锻造Forklift 叉车Free carbide 游离碳化物Free cementite 游离渗碳体Free ferrite 游离铁素体Freeting/fritting 烧结Frictional coefficient 摩擦系数Front slagging 炉前出渣Galvanizing 电镀Gas blow/hole 气孔Gas blowhole 气孔Gaseous diffusion 气体扩散Gassy melt 含气金属液Gas tightness 气密性Gate area 浇口面积Gating = gating system 浇口，浇口系统Gating design 浇口设计Gating proportion/ratio 浇口比Gauge=gage 表，计，规Globular cementite / pearlite 粒状渗碳体/珠光体Grain-boundary segregation 晶界偏析Grain fineness distribution 粒度分布Graphite floatation 石墨漂浮Graphitization 石墨化Green compression strength 湿压强度Gray/grey cast iron 灰铁Grinding 打磨，磨制Grinding wheel 砂轮Heat loss 热损失Heat stress 热应力Heat-treating / heat treatment 热处理Heating effect 热效应Heavy casting 大型铸件/厚壁铸件Heavy-walled 厚壁的Holding furnace 保温炉Hot tear/pool 热裂Hydraulic jack 液压千斤顶Hydrogen 氢Hyxagonal screen 六角筛Impact hardness/toughness 冲击硬度/韧性Impermeability 气密性，不渗透性Impression 压痕，型腔，凹腔Impurity 杂质Included slag 夹渣Indigeous graphite 析出石墨Induction 感应Inoculant 孕育剂Inoculation fade 孕育衰退Inside diameter 内经Instantaneous ladle inoculation / stream inoculation 瞬时浇包孕育Insulation 绝缘，隔离Internal porosity 内缩松Internal shrinkage 内部缩孔Internal stress 内应力Inverse chill 反白口Inverted chill 反白口Iron carbide 渗碳体，碳化铁Iron-coke ratio 铁焦比Jack 千斤顶Jet test 喷射试验（侧电镀层厚度）Job rate 生产定额Knock-off head 易割冒口Knockout 落砂，出芯Knop 钮，电钮Labile 不稳定的Labor-intensive area 强劳动（力）区Ladle 浇包Lamellar pearlite/laminate pearlite 片状珠光体Late inoculation/post inoculation 二次孕育Laying out 设计Leaker 浇漏，漏铁水lift truck 叉车Light casting 小铸件，薄壁铸件Liquidus 液相线Locating point/surface 基准点/面Loss on ignition 烧损Lower limit 下限Luster 光泽Machinability 切削性能Machine allowance 加工余量Machining 机械加工Macrograph 宏观Magnetic flaw detection 磁力探伤Magnetic field 磁场Magnetic-particle inspection 磁粉探伤Magnetic powder inspection 磁粉探伤Magnification 放大倍数，放大倍率Manganese 锰Margin tolerance 极限公差Mass production 大量生产Matrix hardness 机体硬度Mean diameter / stress 平均直径/应力Mean value 中间值Mechanical allowance 加工余量Mechanical property 机械性能Meltableness 可溶性Melting 溶解Melting capacity/ condition / efficiency 熔化率/状况/效率Melting point 熔点Metal graphic microscope 金相显微镜Metallic charge to coke ratio 铁焦比Metallic pattern 金属模Metallograph 金相图片Metallographic examination 金相检验Metallographic laboratory 金相试验室Metallographic microscope 金相显微镜Metallographic specimen 金相磨片Metallurgy 冶金学Metal material 金属材料Microanalysis 微量分析，显微分析Microlug 球化率怀素测定试帮Micron 微米Mismatch 错模Misrun 缺肉，浇不到Modulus of elongation 延伸率Molding line 造型线Natural gas 天然气Nodularization 球化Nodularizer 球化剂Notch brittleness 缺口脆性Off-dimension 尺寸不合格（常指铸件）Off-gage 尺寸不合格（常指型芯）Offset 错位，偏置Operation life 使用期限，寿命Outer inspection / visual inspection 外观检验Outlet 出口，排出口Oxidation 氧化Oxide ferric 氧化铁，三氧化二铁Partial hardening / local hardening 局部淬火Parting face 分型面，分模面Pattern plate 模板Patter spray 脱模液Pattern taper / patter draft 拔模斜度Pearlite 珠光体Permeability test 透气性试验Phosphide 磷共晶，磷化物Physical property 物理性能Pig iron 生铁Pin hole 针孔Pitted skin 麻面（铸造缺陷）Plastic binder 树脂粘结剂Plastic deformation 塑性变形Plate feeder 圆盘给料机Plating 电镀Polishing 抛光Porous casting 不致密铸件，多孔铸件Post inoculation 二次孕育Poured short 未浇满（铸造缺陷）Preheat/preheating 预热Premature freezing 过早凝固Premium casting 保质量逐件，优质逐件Preset program 预定计划，预定程序表Pressure atmosphere 大气压Pressure feeder 加压冒口Production capacity 生产能力Protective gloves 劳保手套Prototype casting 试生产铸件Push-off 推出，顶出Quench aging 淬火时效Radiator 散热器，散热片，暖气片Radioactive element 放射性元素Rare earth 稀土Rare gas 惰性气体Rat 多肉Reamer 铰刀Reclamation 再生，回用Red brittleness=hot brittleness 热脆性Reducibility 还原能力Reduction in area 断面收缩Refractoriness 耐火性Refractory property 耐久性能Regulator 调节器Reinforcement 加固Rejected casting 不合格铸件Resin 树脂Returns 回炉料Reverse chill 反白口Revolving table feeder 圆盘给料机Rimhole 皮下气泡Riser 冒口Rockwell hardness 洛氏硬度Rosette graphite 菊花状石墨Roughing 粗加工’Roughness 粗糙度Rounding 倒角Roust inhibitor 防锈剂Runner gate 横浇道Runner system 浇注系统Running and feeding system 浇冒口系统Rust prevention 防锈Rustless steelSafety and industrial gloves 劳动保护手套Safety factor 安全系数Safety goggle 护目镜Safety precaution 安全措施Sample inspectionSampling 取样Sand blister 砂眼Sand blow 气孔Sand buckle 起皮、夹砂Sand burning 粘砂Sand-conditioning system 砂处理系统Sand control 型砂控制Sand core 砂芯Sand cut 冲砂Sand defects 型砂造成的（铸造）缺陷Sand drop 掉砂Sand explosion 砂眼Sand fineness 砂子平均粒度Sand flowability 型砂流动性Sand mill / sand mixer / sand mixing machine / sand muller 混砂机Sand mold 砂型Sand shakeout 落砂Sand wash 冲砂Scab 铸痂Scar 凹痕Semi-finished product 半成品Sensitivity 敏感性Separate cast test bar = cast integrate test bar 单铸试棒Shakeout 落砂/落砂机Shaking conveyer 震动输送机Shift 班次Short-run 浇不满Short run casting 浇不足铸件，缺肉铸件（未浇满）Shrink hole收缩、锁孔Shrinkage porosity 缩松Shrinkage strain 收缩变形Shrinkhead 冒口Sintering 烧结Size tolerance 尺寸公差Slagging -off 除渣/扒渣Solidification contraction/shrinkage 凝固收缩Solid-liquid interface 固液相交界面Solidus/solidus curve/solidus line 固相线Solution concentration 溶液浓度Sonic inspection 听声检验Specific weight 比重Spectroanalysis 光谱分析Spherical graphite 球状石墨Spheroidal iron = ductile iron 球墨铸铁Spheroidization 球化Spindle 主轴Spotting point 基准点Steam tight test / air tight test 气密性试验Sticker / rat 多肉Straightening 校正Strength test 强度试验Stress 应力Stress relief 应力消除Subskin blowhole / subsurface blow hole / sub-surface blister 皮下气孔Superficial cementation 表面渗碳Super heating 过热Supersaturation 过饱和Surface finish 表面光洁度Surface folding 冷隔Surface roughness 表面粗糙度Swell 胀砂Tap hole 出渣口Telltale 定位标记Tenacity / tensile strength 抗拉强度/韧性Tensile testing machineTension-active element 反球化元素、干扰元素Test bar 试棒Test block 试块Test piece 试样Test specimen 试样/试棒/试块Thermal balance 热平衡Thermal conductivity 导热系数，导热性Thermaldeformation/dilatometer/expansion/fatigue 热变形/膨胀仪//膨胀/疲劳Tightness 紧密度，致密度Tolerance 公差Tooling point 基准点Tuyere gate 风眼Ultimate 极限Upper limit 上限Vacuum treatment 真空处理Ventilating system/device/equipment 通风系统/装置/设备Venting quality透气性Vibratory feeder 震动给料机Vibratory shakeout machine = vibratory shakeout 震动落砂机Visual examination/inspection 外观检验Wash 冲砂Washer 洗砂机Wearability / wear resistance 耐磨性Wrinkle 皱皮Yield strength 屈服强度Zero defect casting 无缺陷铸件Zinc 锌最新铸造标准应用手册（机械工业出版社）（铸造专业词汇）Foundry terminologyfoundry founding casting铸造foundry technology铸造工艺casting铸件sand casting process型砂铸造special casting process特种铸造fluidity流动性mold-filling capacity充型能力gas absorption吸气undercooling ,supercooling过冷degree of undercooling过冷度nucleation成核homogeneous nucleation自发成核heterogeneous nucleation非自发成核solidification range凝固温度范围directional solidification定向凝固solidification contraction凝固收缩liquid contraction液态收缩solid contraction固态收缩solidification time凝固时间free contraction自由收缩hindered contraction受阻收缩shrinkage铸件线收缩率contraction stress收缩应力thermal stress热应力transformation stress相变应力casting stress铸造应力residual stress残留应力metallic raw material金属原物料pig iron生铁ferro-alloy铁合金foundry returns回炉料master alloy中间合金foundry coke铸造焦炭metallurgical coke冶金焦炭fixed carbon固定碳flux熔剂degassing flux除气熔剂covering flux覆盖熔剂refining flux精炼熔剂refractoriness耐火度firebrick耐火砖fireclay耐火黏土silica brick硅砖grain magnesite镁砂molding material造型材料sand砂washed-out sand水洗砂silica sand硅砂natural sand天然砂artificial sand人工砂naturally clay-bonded sand天然粘土砂olivine sand橄榄石砂chromite sand硌铁矿砂zircon sand锆砂carbon sand炭粒砂sharp sand精硅砂red sand红砂chamotte sand熟料砂binder粘结剂clay粘土inorganic binder无机粘结剂organic binder有机粘结剂kaolin高岭土bentonite膨润土sodium bentonite钠基膨润土calcium bentonite钙基膨润土activated bentonite活化膨润土drying oil干性油no bake binder自硬粘结剂（冷硬粘结剂）thermosetting resin binder热固树脂粘结剂oil based binder油类粘结剂water glass binder，sodium silicate binder水玻璃粘结剂lignin liquor纸浆残液synthetic fat binder合脂粘结剂水玻璃模数sodium silicate modulus附加物additives发热剂exothermic mixture分型剂（脱模剂）parting agent；stripping agent 固化剂（硬化剂）hardener悬浮剂suspending agent涂料coating型砂制备（砂处理）sand preparation混砂sand mixing；sand mulling型砂（造型混合料）molding sand芯砂（造芯混合料）core sand合成砂synthetic sand自硬砂self-hardening sand水玻璃砂sodium silicate-bonded sand覆模砂precoated sand烂砂泥（麻泥）loam调匀砂temper sand面砂facing sand背砂（填充砂）backing sand单一砂unit sand含泥量clay content含水量（水分，湿度）moisture content旧砂floor sand枯砂（焦砂）burnt sand废砂waste sand热砂hot sand松砂aeration,sand-cutting筛分（筛析）screen analysis旧砂处理sand reconditioning旧砂再生sand reclamation沉降分选elutriation，decantation型砂试验sand testing透气性permeability流动性flowability型砂强度sand strength湿强度green strength干强度dry strength耐用性（复用性）durability砂型（芯）硬度mold hardness热变形hot deformation残留强度retained strength热强度hot strength韧性toughness发气率（发气速度）gas evolution rate发气性（发气量）gas evolution吸湿性moisture absorption落砂性knock-out capability溃散性collapsibility胶质价colloid index破碎指数shatter index热气流烘砂装置hot pneumatic tube drier混砂机sand muller，sand mixer松砂机aerator ，sand cutter冷却提升机cooling elevator，coolevator筛砂机riddle磁力滚筒magnetic separator旧砂再生设备sand reclamation气力输送装置pneumatic tube conveyor铸铁cast iron铸铁石墨形态morphology of graphite in cast iron灰铸铁（灰口铸铁）gray cast iron白口铸铁white cast iron麻口铸铁mottled cast iron共晶度degree of saturation碳当量carbon equivalent片状石墨flake graphite 初生石墨primary graphite孕育铸铁inoculated cast iron球墨铸铁spheroidal graphite cast iron，nodular graphite iron，ductile iron球状石墨spheroidal graphite，nodular graphite 可锻铸铁（马铁）malleable cast iron黑心可锻铸铁black heart malleable cast iron珠光体可锻铸铁pearlitic malleable cast iron铁素体可锻铸铁ferritic malleable cast iron白心可锻铸铁white heart malleable cast iron团絮石墨tempered graphite冷硬铸铁（激冷铸铁）chilled iron耐磨铸铁wear resisting cast iron耐热铸铁heat resisting cast iron耐酸铸铁acid resisting cast iron高硅铸铁high silicon cast iron蠕墨铸铁vermicular cast iron，compacted graphite cast iron蠕虫状石墨vermicular graphite合金铸铁alloy cast iron铸钢cast steel碳素铸钢carbon cast steel低合金铸钢low alloy cast steel高锰钢high manganese steel铁素体钢ferritic steel青铜bronze铅青铜lead bronze铝青铜aluminum bronze黄铜brass铝铜合金aluminum-copper alloy铝镁合金aluminum-magnesium alloy铝硅合金aluminum-silicon alloy镁合金magnesium alloy轴承合金（减摩合金）bearing metal，antifrictional metal巴氏合金Babbitt metal钛合金titanium alloy熔化（熔炼）melting重熔remelting炉料charge熔化率melting rate炉料计算charge calculation双联熔炼duplexing元素烧损（元素烧损率）melting losses ofvarious chemical elements熔炼损耗(烧损) total melting loss 还原气氛reducing atmosphere氧化气氛oxidizing atmosphere惰性气体inert gas碱度index of basicity碱性渣basic slag酸性渣acid slag精炼refining遗传性heredity风口比tuyere ratio有效高度effective height送风强度blast intensity预热送风hot blast底焦coke bed层焦coke split隔焦buffer coke charge炉衬furnace lining碱性炉衬acid lining棚料bridging熔池bath吸碳carbon pick-up焦铁比iron coke ratio出渣deslagging打炉cupola drop氧化熔炼法oxidizing melting不氧化熔炼法dead melting真空熔炼vacuum refining熔渣slag沉渣sludge浮渣dross,cinder氧化期oxidizing stage还原期blocking stage还原渣reducing slag氧化渣oxidizing slag白渣white slag脱氧deoxidation扒渣slagging-off脱碳decarburization脱硫desulphurization脱磷dephosphorization增碳recarburizing 脱氧剂deoxidizer挥发损耗volatilizing losses静置stewing，holding吹氮nitrogen flushing冲天炉cupola水冷冲天炉water-cooled cupola热风冲天炉hot blast cupola湿法除尘器wet cap炉缸cupola well前炉forehearth冲天炉加料机cupola charging machine爬式加料机ship hoist电磁配料称electro-magnetic weighing balancer 电磁盘electromagnetic chuck电弧炉direct arc furnace感应电炉electric induction furnace电渣炉electroslag furnace电磁搅拌electromagnetic agitation浇包ladle摇包shaking ladle底浇包bottom pouring ladle保温炉holding furnace坩呙炉crucible furnace孕育inoculation多孔塞法porous plug process变质modification墨化剂graphitizer过热superheating石墨球化处理nodularizing treatment of graphite碳当量仪eutectometer三角试块wdge test-piece真空除气vacuum degassing浇注pouring保护气氛浇注pouring under controlled atmosphere浇注速度pouring rate浇注温度pouring temperature浇注时间pouring time浇注位置pouring position型内孕育inmold inoculation压铁weight点冒口teeming捣冒口pumping补炉patching炉龄campaign铸造工艺设计mold design铸造工艺装备设计foundry tools design铸造工艺图foundry molding drawing铸件图drawing of rough casting起模斜度pattern draft收缩余量shrinkage allowance工艺补正量molding allowance加工余量machining allowance吃砂量mo9ld thickness补贴pad分型负数joint allowance铸件尺寸公差dimensional allowance of casting 铸件重量公差weight allowance of casting铸件加工基准面reference face for machining of casting铸件表面粗糙度surface roughness of casting浇注系统（浇口）gating system，running system 封闭式浇注系统chocked running system，pressurized gating system半封闭式浇注系统enlarged runner system开放式浇注系统unchecked running system，non-pressurized gating system浇口盆（外浇口）pouring basin浇口杯pouring cup浇口塞blanking-off plug直浇道sprue直浇道窝sprue base横浇道runner筛网芯（滤网芯）strainer core内浇道ingate离心集渣浇注系统whirl gate，dirt trap system 顶注式浇注系统top gating system底注式浇注系统bottom gating system阶梯式浇注系统step gating system雨淋浇口shower gate缝隙浇口slot gate 压边浇口lip runner，kiss runner牛角式浇口horn gate热结hot spot冒口riser，feeder head冒口效率riser efficiency明冒口open riser暗冒口bland riser侧冒口（边冒口）side riser压力冒口pressure riser大气压力冒口atmospheric riser发气压力冒口（气弹冒口）gas-delivered pressure riser透气砂芯pencil core冒口径riser neck冒口根riser pad保温冒口套heat insulating feeder sleeve发热冒口套exorhermic feeder sleeve补缩距离feeding distance，feeding zone易割冒口knock-off head易割片（易割芯片）washburn core铸造工艺装备foundry tools and equipment模样（铸模、模）pattern母模master金属模metal pattern骨架模skeleton pattern石膏模plaster pattern塑料模plaslicn pattern整体模one-piece pattern分开模parted pattern，split pattern活块loose piece模板pattern plate模底板pattern mounting plate单面模板single face pattern plate双面模板match plate放样（伸图）hot dimensional drawing缩尺（模样工缩尺）shrinkage rule，pattern-maker’s rule芯盒core box脱落式芯盒troughed core box下芯量具core setting scale下芯夹具core jig烘芯板core drying plate砂箱flask，molding box箱带（箱挡）flask bar，cross bar脱箱snap flask套箱mold jacket套销hollow pin，stub pin造型molding型腔mold cavity7.1.3铸型mold砂型sand mold上箱cope , top part下箱drag , bottom part手工造型hand molding机器造型machine molding自动化造型automatic molding分型面mold joint有箱造型flask molding两箱造型two-part molding三箱造型three-part molding不平分型面stepped joint无箱造型flaskless molding脱箱造型removable flask molding地坑造型pit molding刮板造型sweep molding抛砂造型impeller ramming组芯造型core assembly molding假箱造型oddside molding微振压造型vibratory squeezing molding 高压造型high pressure molding湿砂型green sand mold干砂型dry sand mold砂型烘干mold drying干砂型（干型）dry sand mold表面烘干型skin dried mold烂砂泥型loam mold砂床bed过渡角transition angle吊砂cod砂钩lifter负亚造型vacuum molding液态砂造型fluid sand molding 漏砂pattern stripping填砂molding-filling紧实ramming震实jolt ramming压实squeezing ramming紧实度degree of ramming二氧化碳法造型2CO process自硬砂造型self-hardening sand molding塞砂tucking刮砂strike-off造型生产线molding line刷水swabbing扎出气孔venting排气道venting channel修型patching冷铁densener，chill外冷铁surface densener内冷铁internal densener验型（验箱）trial closing合型（合箱、组型）mold assembling，closing造芯（制芯）core making芯（芯子）core芯骨core rod，core scab油砂芯oil sand core预制砂embeded core，ram up core芯头core print芯座core print芯头斜度core print taper芯头间隙core print clearance壳芯shell core烘芯core baking通气蜡线vent wax冷芯盒法cold box process热芯盒法hot box process芯撑chaplethand tools of molding压勺heart and spoon提钩cleaner双头铜勺double ended radius sleeker镘刀trowel造型机molding machine压实造型机squeezing molding machine震击台bumper振动台vibrating table微振压实造型机vibratory squeezer震实造型机jolt molding machine高压造型机high pressure molding machine射压造型机shooting and squeezing molding machine多触头造型机equalizing piston squeezer抛砂机sand slinger起模机drawing machine射芯机core shooter击芯机core extruder铸型输送机mold conveyor落砂shake-out除芯decoring喷砂清理sand blasting抛丸清理shot blasting水力清砂hydraulic blast水砂清砂hydraulic blast清理cleaning清砂cleaning火焰表面清理scarfing清铲chipping化学清砂chemical cleaning精整dressing and finishing落砂机knock-out machine抛丸清理机shot blast machine清理滚筒tumbling barrel抛丸落砂清理设备shot blast reclaiming equipment悬挂式磨轮swing frame grinder矫正coining焊补repair welding参补impregnation金属型铸造permanent mold casting金属型metal mold金属芯metal core覆砂金属型sand-lined metal mold排气赛venting plug排气槽air vent 龟裂heat checking金属型铸造机gravity die casting machine压力铸造die-casting压铸型die-casting die动型moving die定型fixed die合型力clamping force压室pressure chamber鹅颈管gooseneck分流器spreader顶杆ejector pin溢流槽overflow well压射冲头injection piston压射比压injection pressure压射速度injection speed保压时间dwell time真空压铸vacuum die casting冲氧压铸pore-free die casting双冲头压铸acurad die casting压铸机die casting machine冷室压铸机cold chamber die casting machine 热室压铸机hot chamber die casting machine 镶铸法insert process离心铸造true centrifugal casting半离心铸造semi-centrifugal casting离心浇注centrifugal pressure casting双金属离心铸造bimetal centrifugal casting 离心铸造机centrifugal casting machine失模铸造lost pattern casting熔模铸造fusible pattern molding压制熔模fusible pattern injection压型pattern die熔模fusible pattern盐模salt pattern蜡模wax-pattern模组pattern assembly熔模涂料slurry面层涂料investment precoat撒砂stuccoing脱蜡dewaxing培烧sintering壳型制造shell molding结壳时间investing time结壳温度investing temperature硬化温度curing temperature硬化时间curing time陶瓷型制造ceramic slurry灌浆paste pouring喷烧torch firing低压铸造low-pressure diecasting充型压力mold filling pressure保压压力dwell pressure升液管stalk真空吸铸suction casting差压铸造counter-pressure casting实型铸造full mold process泡沫塑料模Styrofoam pattern磁型铸造magnetic shot molding process凝壳铸造slush casting石膏型造型plaster molding连续铸造continuous casting铸件检验inspection of casting铸件质量分析quality analysis of casting铸件外观质量visual quality of casting铸件内在质量internal quality of casting铸件使用性能service ability of casting单铸试块separated test bar of casting附铸试块test lug缺陷铸件defective casting废品reject无损检验（无损探伤）nondestructive inspection 破坏性试验destructive testing飞翅（飞边）joint flash毛刺veining抬型（抬箱）cope raise，raised mold胀砂swell冲砂erosion，cut，wash掉砂drop，crush外渗物（外渗豆）sweat气孔blowhole针孔pinhole缩孔shrinkage缩松dispersed shrinkage疏松（显微缩松）porosity，microshrinkage冷裂cold cracking热裂hot tearing热处理裂纹heat treatment crack白点（发裂）flake冷隔cold shut，cold lap浇注断流interrupted pour鼠尾rat-tail沟槽buckle夹砂结疤（夹砂）scab机械粘砂(渗透粘砂) metal penetration 化学粘砂（烧结粘砂）burn-on表面粗糙rough surface皱皮elephant skin缩陷depression浇不到misrun未浇满poured short跑火run-out，bleeding型漏（漏箱）run-out，bleeding损伤（机械损伤）damage拉长exaggeration of dimension超重over-weight变形distortion，warping错型（错箱）shift错芯core shift偏芯（漂芯）core raised，corelift夹杂物inclusion冷豆cold shot内渗物（内渗豆）internal sweat渣气孔scum，slag-blow hole砂眼sand inclusion亮皮pearlite layer菜花头cauli-flowering石墨漂浮carbon flotation石墨集结kish graphite spot组织粗大open grain structure偏析segregation硬点hard spot反白口inverse chill球化不良under-nodularizing球化衰退degradated spheroidisation 脱碳decarburization。
模具英语专业术语
模具英语专业术语模具的分类:冲压模(五金模): stamping die分离模: cutting die成形模: forming die塑胶模: plastics mold注射模: injection mold压缩模: compression mold铸塑模: transfer mold吹塑模: blow mold吸塑模: suck mold铸造模: casting die砂型铸造: sand casting压铸模: die casting锻造模: forging die塑胶模具术语一、入水：gate进入位(入水点)：gate location水口形式：gate type大水口(侧浇口): edge gate潜水口: sub-gate薄膜式水口: film gate牛角式潜水口: banana gate扇形水口: fan gate环形水口: ring gate二次水口:细水口：pin-point gate水口大小：gate size转水口：switching runner/gate唧嘴口径：sprue diameter直接水口: direct gate二、流道: runner热流道：hot runner,hot manifold热嘴冷流道: hot sprue/cold runner唧嘴直流: direct sprue gate圆形(整圆/半圆)流道：round(full/half) runner矩形流道: rectangle runner梯形流道: trapezoid runnerU形流道: U shape runner流道电脑分析(模流分析)：mold flow analysis流道平衡: runner balance热嘴：hot sprue/tip热流道板：hot manifold发热管：cartridge heater探针: thermocouples插头：connector plug插座：connector socket密封/封料：seal三、运水：water line喉塞：line plug喉管：tube塑胶管：plastic tube快速接头：jiffy quick connector plug/socket 四、模具零件：mold components 三板模(细水口模)：3-plate mold二板模(大水口模)：2-plate mold热流道模具: hot-runner/manifold mold叠层模: stacked mold边钉/导边：leader pin/guide pin边司/导套：guide pin/guide bushing直导套：shoulder guide bushing有托导套：straight guide bushing中托司：ejector guide bush中托边：ejector guide pin回针: return pin面板: top clamp plateA板: A plate推板：stripper plateB板: B plate托板：support plate方铁: spacer block加高方铁: higher spacer block顶针固定板：ejector retainner plate顶针板：ejector plate底板: bottom clamp plate螺丝：screw杯头螺丝: socket cup head screw平头螺丝: socket flat head screw机米螺丝:外六角头螺丝: bolt栓打螺丝(等高螺丝)：S.H.S.B管钉：dowel pin开模槽：ply bar socket内模管位(模仁互锁)：core/cavity inter-lock顶针：ejector pin司筒：ejector sleeve司筒针：sleeve ejector pin缩呵：movable core,return core, core puller 扣机（尼龙拉勾）：nylon latch lock斜顶：lifter模胚（架）：mold base上内模：cavity insert下内模：core insert行位（滑块）：slide行位扣:镶件：insert压座/斜鸡：wedge耐磨板/油板：wear plate压条：gib撑头: support pillar唧嘴：sprue bushing挡板：stop plate定位圈(法兰)：locating ring锁扣(模锁)：latch扣鸡：parting lock set推杆：push bar顶板：eracuretun活动臂：lever arm分流锥：spure sperader水口司:bush垃圾钉：stop pin隔片：buffle弹弓柱：spring rod弹弓:die spring型腔(前模仁): cavity型芯(后模仁): core镶针：insert pin销子(销钉)：dowel pin波子弹弓：ball catch喉塞(堵头): pipe plug锁模块：lock plate斜顶杆：angle ejector rod斜顶针：angle from pin尼龙拉勾：parting locks活动臂：lever arm复位键、提前回杆：early return bar气阀：valves斜导边(斜导柱)：angle pin油缸: hydraulic cylinder液压马达: hydraulic motor齿轮: gear轴承: bear术语：terms承压平面平衡：parting surface support balance分模面排气：parting line venting回针碰料位：return pin and cavity interference模总高超出啤机规格：mold base shut hight顶针碰运水：water line interferes with ejector pin料位出上/下模：part from cavity (core) side模胚原身出料位：cavity direct cut on A-plate,core direct cut on B-plate. 不准用镶件：Do not use (core/cavity) insert用铍铜做镶件：use beryllium copper insert初步模图设计：preliminary mold design正式模图设计：final mold design反呵：reverse core弹弓压缩量：spring compressed length稳定性好：good stability,stable强度不够：insufficient rigidity均匀冷却：even cooling扣模(粘模)：sticking顶白: stress mark热膨胀：thero expansion缩水: shrinkage物料表: BOM原料: raw materials物料: materials工程试模材料: material for engineering mold testing成品: finished product半成品: semi-finished product公差：tolorance铜公(电极)：copper electrode射料不足: short shot缺口: nick瑕疪(斑点): speck亮斑: shine银纹: splay焦痕: gas mark起鳞: delamination冷块: cold slug导色: blush沟槽;凿槽: gouge段面咬花: satin texture证示线: witness line专利: patent沙砾: grit细粒: granule=peuet=grain抽粒机: grit maker缓冲: cushion不锈钢: stainless steel镁铝合金: magnalium镁金属: magnesium钣金: metal plate车/车床: lathe铣床/铣床: mill刨/刨床: plane磨/磨床: grind钻/钻床: drill镗: boring气泡: blinster版次: revision备注: remark生产确认: production control confirmation 初审: checked by核准: approved by部门: department电镀: plate成型: molding样品: sample雕刻: engrave蚀纹: texture加硬: harden热处理: heat treatment淬火: quenching回火: tempering退火: annealing碳化: carbonization铬酸处理: chromate阳性处理: anodize氮化: nitrifying。
锻造用英语术语
锻造用英语术语filling in 填砂film play 液面花纹finishing slag 炼后熔渣flash gutter 锻模飞边槽flask molding 砂箱造模forging roll 辊锻机formboard 进模口板gutter 锻模飞边槽hammer man 锻工heading machine 顶镦机impacter 卧式锻造机inblock cast 整体铸造ingot 铸锭ingot blank 铸坯inlay casting 镶铸法investment casting 失模铸造isothermal forging 恒温锻造loose piece 木模活块molding pit 铸模地坑pouring process 浇注法recasting 重铸roll forging 轧锻rolled surface 轧制表面rough sand 粗砂roughing forge 粗锻sand crushing 塌箱seamless forging 无缝锻造separate 分离shave 崩砂shrinkage fit 收缩配合shut height 闭合高度sieve mesh 筛孔sintering of sand 铸砂烧贴slag 熔渣slag inclusion 夹渣stickness 黏模性strip layout 带状胚料排样法tap casting 顶注top gate 顶注浇口unworked casting 不加工铸件upender 翻转装置upending 顶锻uphill casting 底铸white cast iron 白口铸件accretion 炉瘤acid converter 酸性转炉acid lining cupola 酸性熔铁炉acid open-hearth furnace 酸性平炉aerator 松砂机air set mold 常温自硬铸模airless blasting cleaning 离心喷光all core molding 集合式铸模all round die holder 通用模座assembly mark 铸造合模记号back pouring 补浇注backing sand 背砂base bullion 粗金属锭base permeability 原砂透气度belling 压凸billet 坏料bleed 漏铸blocker 预锻模膛blocking 粗胚锻件blow hole 铸件气孔board drop hammer 板落锤bottom pour mold 底浇bottom pouring 底注boxless mold 脱箱砂模break-off core 缩颈砂心brick molding 砌箱造模法buckle 剥砂面camber 错箱camlachie cramp 铸包cast blade 铸造叶片casting flange 铸造凸缘casting on flat 水平铸造chamotte sand 烧磨砂charging hopper 加料漏斗cleaning of casting 铸件清理closed-die forging 合模锻造core compound 砂心黏结剂core template 砂心模板core vent 砂蕊排气孔corner gate 压边浇口counter blow hammer 对击锻造counter lock 止口镶嵌方式depression 外缩凹孔die approach 模口角度draw out 锻造拔长draw plate 起模板draw spike 起模长针dummying 预锻embedded core 加装砂心erosion 冲砂fettling 铸件清理filling core 埋入砂心。
模具专业英语术语..
模具工程常用词汇模具钢材alloy tool steel 合金工具钢aluminium alloy 铝合金钢bearing alloy 轴承合金blister steel 浸碳钢bonderized steel sheet 邦德防蚀钢板carbon tool steel 碳素工具钢clad sheet 被覆板clod work die steel 冷锻模用钢emery 金钢砂ferrostatic pressure 钢铁水静压力forging die steel 锻造模用钢galvanized steel sheet 镀锌铁板hard alloy steel 超硬合金钢high speed tool steel 高速度工具钢hot work die steel 热锻模用钢low alloy tool steel 特殊工具钢low manganese casting steel 低锰铸钢marging steel 马式体高强度热处理钢martrix alloy 马特里斯合金meehanite cast iron 米汉纳铸钢meehanite metal 米汉纳铁merchant iron 市售钢材molybdenum high speed steel钼系高速钢molybdenum steel钼钢nickel chromium steel 镍铬钢prehardened steel 顶硬钢silicon steel sheet 硅钢板stainless steel 不锈钢tin plated steel sheet 镀锡铁板tough pitch copper 韧铜troostite 吐粒散铁tungsten steel 钨钢vinyl tapped steel sheet 塑料覆面钢板四、模具零件：mold components三板模：3-plate mold二板模：2-plate mold边钉/导边：leader pin/guide pin边司/导套：bushing/guide bushing中托司：shoulder guide bushing中托边L：guide pin顶针板：ejector retainner plate托板：support plate螺丝：screw管钉：dowel pin开模槽：ply bar scot内模管位：core/cavity inter-lock顶针：ejector pin司筒：ejector sleeve司筒针：ejector pin推板：stripper plate缩呵：movable core,return core core puller扣机（尼龙拉勾）：nylon latch lock斜顶：lifter模胚（架）：mold base上内模：cavity insert下内模：core insert行位（滑块）：slide镶件：insert压座/斜鸡：wedge耐磨板/油板：wedge wear plate压条：plate撑头: support pillar唧嘴：sprue bushing 挡板：stop plate定位圈：locating ring锁扣：latch扣鸡：parting lock set推杆：push bar栓打螺丝：S.H.S.B顶板：eracuretun活动臂：lever arm分流锥：spure sperader水口司:bush垃圾钉：stop pin隔片：buffle弹弓柱：spring rod弹弓:die spring中托司：ejector guide bush中托边：ejector guide pin镶针：pin销子：dowel pin波子弹弓：ball catch喉塞: pipe plug锁模块：lock plate斜顶：angle from pin斜顶杆：angle ejector rod尼龙拉勾：parting locks活动臂：lever arm复位键、提前回杆：early return bar气阀：valves斜导边：angle pin术语：terms承压平面平衡：parting surface support balance模排气：parting line venting回针碰料位：return pin and cavity interference模总高超出啤机规格：mold base shut hight顶针碰运水：water line interferes withejector pin料位出上/下模：part from cavith (core) side模胚原身出料位：cavity direct cut on A-plate,core direct cut on B-plate.不准用镶件：Do not use (core/cavity) insert用铍铜做镶件：use beryllium copper insert初步（正式）模图设计：preliinary (final) mold design反呵：reverse core弹弓压缩量：spring compressed length稳定性好：good stability,stable强度不够：insufficient rigidity均匀冷却：even cooling扣模：sticking热膨胀：thero expansion公差：tolorance铜公(电极）：copper electrode模具工程常用词汇die 模具die shoe 模座figure file, chart file图档cutting die, blanking die冲模progressive die, follow (-on)die 连续模compound die复合模punched hole冲孔 panel board镶块to cutedges=side cut=side scrap切边to bending折弯to pull, to stretch拉伸Line streching, line pulling线拉伸engraving, to engrave刻印upsiding down edges翻边to stake铆合design modification设计变化 die block模块folded block折弯块sliding block滑块location pin定位销lifting pin顶料销die plate, front board范本padding block垫块stepping bar垫条upper die base上模lower die base下模座upper supporting blank上承板upper padding plate blank上垫板spare dies模具备品spring 弹簧 bolt螺栓plate电镀mold成型material for engineering mold testing工程试模材料not included in physical inventory不列入盘点incoming material to be inspected进货待验PCE assembly production schedule sheet PCE组装厂生产排配表model机钟work order工令revision版次production control confirmation生产确认checked by初审approved by核准stock age analysis sheet 库存货龄分析表on-hand inventory现有库存available material良品可使用obsolete material良品已呆滞to be inspected or reworked 待验或重工cause description原因说明part number/ P/N 料号item/group/class类别prepared by制year-end physical inventory difference analysis sheet 年终盘点差异分析表physical inventory盘点数量physical count quantity账面数量difference quantity差异good product/accepted goods/ accepted parts/good parts 良品defective product/non-good parts不良品disposed goods处理品on way location在途仓oversea location海外仓spare parts physical inventory list 备品盘点清单spare molds location模具备品仓skid/pallet栈板tox machine自铆机wire EDM线割 EDM放电机coil stock卷料sheet stock片料tolerance工差score=groove压线cam block滑块pilot导正筒trim剪外边pierce剪内边drag form压锻差pocket for the punch head挂钩槽slug hole废料孔feature die公母模expansion dwg展开图radius半径shim(wedge)楔子torch-flame cut火焰切割set screw止付螺丝form block折刀stop pin定位销round pierce punch=die button圆冲子shape punch=die insert异形子stock locater block定位块under cut=scrap chopper清角active plate活动板baffle plate挡块cover plate盖板male die公模female die母模groove punch压线冲子air-cushion eject-rod气垫顶杆spring-box eject-plate弹簧箱顶板bushing block衬套insert 入块capability能力parameter参数 factor系数phosphate皮膜化成viscosity涂料粘度alkalidipping脱脂main manifold主集流脉bezel斜视规blanking穿落模dejecting顶固模demagnetization去磁;消磁high-speed transmission高速传递heat dissipation热传rack上料degrease脱脂rinse水洗alkaline etch龄咬 desmut剥黑膜 D.I. rinse纯水次 Chromate铬酸处理 Anodize阳性处理 seal封孔 revision 版次 part number/P/N料号 good products良品 scraped products报放心品 defective products不良品 finished products成品 disposed products处理品 barcode条形码 flow chart流程窗体 assembly组装 stamping冲压 molding成型 spare parts=buffer备品 coordinate坐标 dismantle the die折模 auxiliary fuction 辅助功能 poly-line多义线 heater band 加热片 thermocouple热电偶 sand blasting喷沙 grit 砂砾 derusting machine除锈机 degate打浇口 dryer烘干机 induction感应 induction light感应光 response=reaction=interaction感应 ram连杆 edge finder巡边器 concave凸 convex凹 short射料不足 nick缺口 speck瑕疵 shine亮班 splay 银纹 gas mark焦痕 delamination起鳞 cold slug冷块 blush 导色 gouge沟槽;凿槽 satin texture段面咬花 witness line证示线 patent专利 grit沙砾 granule=peuet=grain细粒 grit maker抽粒机cushion缓冲 magnalium镁铝合金 magnesium镁金 metal plate钣金 lathe车 mill锉 plane刨 grind磨 drill铝 boring镗 blinster气泡 fillet镶;嵌边 through-hole form通孔形式 voller pin formality滚针形式 cam driver铡楔 shank 摸柄 crank shaft曲柄 augular offset角度偏差 velocity速度 production tempo生产进度现状 torque扭矩 spline=the multiple keys花键quenching淬火 tempering 回火annealing退火 carbonization碳化 alloy合金 tungsten high speed steel钨高速的 moly high speed steel钼高速的 organic solvent有机溶剂 bracket小磁导 liaison联络单 volatile挥发性resistance 电阻 ion离子 titrator滴定仪 beacon警示灯 coolant冷却液 crusher破碎机模具工程类 plain die简易模 pierce die 冲孔模 forming die成型模 progressive die连续模 gang dies复合模 shearing die剪边模 riveting die铆合模 pierce 冲孔 forming成型(抽凸,冲凸) draw hole抽孔 bending折弯 trim切边 emboss凸点dome凸圆 semi-shearing半剪 stamp mark冲记号 deburr or coin压毛边 punch riveting冲压铆合 side stretch侧冲压平 reel stretch卷圆压平 groove压线 blanking下料 stamp letter冲字(料号) shearing剪断 tick-mark nearside正面压印 tick-mark farside反面压印冲压名称类 extension dwg展开图 procedure dwg工程图 die structure dwg模具结构图 material材质 material thickness料片厚度press specification冲床规格 die height range适用模高 die height闭模高度 burr毛边 gap间隙 punch wt.上模重量五金零件类inner guiding post内导柱 inner hexagon screw内六角螺钉 dowel pin固定销coil spring弹簧 lifter pin顶料销 eq-heightsleeves=spool等高套筒 pin销 lifter guide pin浮升导料销 guide pin导正销wire spring圆线弹簧 outer guiding post 外导柱 stop screw止付螺丝 located pin定位销 outer bush 外导套范本类top plate上托板（顶板） top block上垫脚 punch set上模座 punch pad上垫板 punch holder上夹板stripper pad脱料背板up stripper上脱料板 male die公模(凸模) feature die公母模 female die母模(凹模) upper plate上模板lower plate下模板 die pad下垫板 die holder下夹板 die set下模座 bottom block下垫脚 bottom plate下托板(底板) stripping plate内外打(脱料板)outer stripper外脱料板 inner stripper内脱料板 lower stripper下脱料板零件类 punch冲头 insert入块(嵌入件) deburring punch压毛边冲子 groove punch压线冲子 stamped punch字模冲子 round punch圆冲子 special shape punch异形冲子 bending block折刀 roller滚轴 baffle plate挡块 located block定位块 supporting block for location 定位支承块 air cushion plate气垫板 air-cushion eject-rod气垫顶杆 trimming punch切边冲子 stiffening rib punch一、 = stinger 加强筋冲子 ribbon punch压筋冲子 reel-stretch punch卷圆压平冲子 guide plate定位板 sliding block滑块 sliding dowel block滑块固定块 active plate活动板 lower sliding plate下滑块板 upper holder block上压块 upper mid plate上中间板 spring box弹簧箱 spring-box eject-rod弹簧箱顶杆 spring-box eject-plate弹簧箱顶板 bushing bolck衬套 cover plate盖板guide pad导料块塑件&模具相关英文compre sion molding压缩成型 flash mold溢流式模具 plsitive mold挤压式模具split mold分割式模具 cavity型控母模 core模心公模 taper锥拔 leather cloak仿皮革 shiver饰纹 flow mark流痕 welding mark溶合痕 post screw insert螺纹套筒埋值self tapping screw自攻螺丝 striper plate脱料板piston活塞 cylinder汽缸套 chip细碎物 handle mold掌上型模具（移转成型用模具） encapsulation molding低压封装成型（射出成型用模具）two plate两极式（模具） well type蓄料井 insulated runner 绝缘浇道方式 hot runner热浇道 runner plat浇道模块 valve gate阀门浇口 band heater环带状的电热器 spindle阀针 spear head刨尖头 slag well冷料井 cold slag冷料渣 air vent排气道 welding line熔合痕 eject pin顶出针 knock pin顶出销 return pin回位销反顶针 sleave套筒 stripper plate脱料板 insert core放置入子runner stripper plate浇道脱料板 guide pin导销 eject rod (bar)（成型机）顶业捧 subzero深冷处理three plate三极式模具runner system浇道系统 stress crack应力电裂 orientation 定向 sprue gate射料浇口，直浇口 nozzle射嘴 sprue lock pin料头钩销(拉料杆) slag well冷料井 side gate侧浇口 edge gate侧缘浇口 tab gate搭接浇口 film gate薄膜浇口 flash gate闸门浇口slit gate缝隙浇口 fan gate扇形浇口 dish gate因盘形浇口 diaphragm gate隔膜浇口 ring gate环形浇口 subarine gate潜入式浇口tunnel gate隧道式浇口 pin gate针点浇口 Runner less无浇道 (sprue less)无射料管方式 long nozzle延长喷嘴方式 sprue浇口;溶渣各种模具常用成形方式 accurate die casting 精密压铸 powder forming 粉末成形 calendaring molding 压延成形 powder metal forging 粉末锻造cold chamber die casting 冷式压铸precision forging 精密锻造cold forging 冷锻press forging 冲锻compacting molding 粉末压出成形rocking die forging 摇动锻造compound molding 复合成形rotary forging 回转锻造compression molding 压缩成形rotational molding 离心成形dip mold 浸渍成形rubber molding 橡胶成形encapsulation molding 注入成形sand mold casting 砂模铸造extrusion molding 挤出成形shell casting 壳模铸造foam forming 泡沫成形sinter forging 烧结锻造forging roll 轧锻six sides forging 六面锻造gravity casting 重力铸造slush molding 凝塑成形hollow(blow) molding 中空(吹出)成形squeeze casting 高压铸造hot chamber die casting 热室压铸swaging 挤锻hot forging 热锻transfer molding 转送成形injection molding 射出成形warm forging 温锻investment casting 精密铸造matched die method 对模成形法 laminating method 被覆淋膜成形low pressure casting 低压铸造lost wax casting 脱蜡铸造matched mould thermal forming 对模热成形模各式模具分类用语bismuth mold 铋铸模landed plunger mold 有肩柱塞式模具burnishing die 挤光模landed positive mold 有肩全压式模具button die 镶入式圆形凹模loading shoe mold 料套式模具center-gated mold 中心浇口式模具loose detail mold 活零件模具chill mold 冷硬用铸模loose mold 活动式模具clod hobbing 冷挤压制模louvering die 百叶窗冲切模composite dies 复合模具manifold die 分歧管模具counter punch 反凸模modular mold 组合式模具double stack mold 双层模具multi-cavity mold 多模穴模具electroformed mold 电铸成形模multi-gate mold 复式浇口模具expander die 扩径模 offswt bending die 双折冷弯模具extrusion die 挤出模palletizing die 迭层模family mold 反套制品模具plaster mold 石膏模transfer die连续自动冲切,连续冲模blank through dies 漏件式落料模porous mold 通气性模具duplicated cavity plate 复板模positive mold 全压式模具fantail die 扇尾形模具pressure die 压紧模fishtail die 鱼尾形模具profile die 轮廓模flash mold 溢料式模具progressive die 顺序模gypsum mold 石膏铸模protable mold 手提式模具hot-runner mold 热流道模具prototype mold 雏形试验模具ingot mold 钢锭模punching die 落料模lancing die 切口模raising(embossing) 压花起伏成形re-entrant mold 倒角式模具sectional die 拼合模runless injection mold 无流道冷料模具sectional die 对合模具segment mold 组合模 semi-positive mold 半全压式模具shaper 定型模套single cavity mold 单腔模具solid forging die 整体锻模split forging die 拼合锻模split mold 双并式模具sprueless mold 无注道残料模具squeezing die 挤压模stretch form die 拉伸成形模sweeping mold 平刮铸模swing die 振动模具three plates mold 三片式模具trimming die 切边模unit mold 单元式模具universal mold 通用模具unscrewing mold 退扣式模具yoke type die 轭型模模具厂常用之标准零配件air vent vale 通气阀anchor pin 锚梢angular pin 角梢baffle 调节阻板angular pin 倾斜梢baffle plate 折流檔板ball button 球塞套ball plunger 定位球塞ball slider 球塞滑块binder plate 压板blank holder 防皱压板blanking die 落料冲头bolster 上下范本bottom board 浇注底板bolster 垫板bottom plate 下固定板bracket 托架bumper block 缓冲块buster 堵口casting ladle 浇注包casting lug铸耳 cavity 模穴(模仁)cavity retainer plate 模穴托板center pin 中心梢clamping block 锁定块coil spring 螺旋弹簧cold punched nut 冷冲螺母cooling spiral 螺旋冷却栓core 心型core pin 心型梢cotter 开口梢cross 十字接头cushion pin 缓冲梢diaphragm gate 盘形浇口die approach 模头料道die bed 型底 die block 块形模体die body 铸模座die bush 合模衬套die button 冲模母模die clamper 夹模器die fastener 模具固定用零件die holder 母模固定板die lip 模唇die plate 冲范本die set 冲压模座direct gate 直接浇口dog chuck 爪牙夹头dowel 定位梢dowel hole 导套孔dowel pin 合模梢dozzle 辅助浇口dowel pin 定位梢draft 拔模锥度draw bead 张力调整杆drive bearing 传动轴承ejection pad 顶出衬垫ejector 脱模器ejector guide pin 顶出导梢ejector leader busher 顶出导梢衬套ejector pad 顶出垫ejector pin 顶出梢ejector plate 顶出板ejector rod 顶出杆 ejector sleeve 顶出衬套ejector valve 顶出阀eye bolt 环首螺栓filling core 椿入蕊film gate 薄膜形浇口finger pin 指形梢finish machined plate 角形范本finish machined round plate 圆形范本fixed bolster plate 固定侧模板flanged pin 带凸缘销flash gate 毛边形浇口flask 上箱floating punch 浮动冲头gate 浇口gate land 浇口面gib 凹形拉紧楔goose neck 鹅颈管guide bushing 引导衬套guide pin 导梢guide post 引导柱guide plate 导板guide rail 导轨head punch 顶头冲孔headless punch 直柄冲头heavily tapered solid 整体模蕊盒hose nippler 管接头impact damper 缓冲器injection ram 压射柱塞inlay busher 嵌入衬套inner plunger 内柱塞inner punch 内冲头insert 嵌件insert pin 嵌件梢king pin 转向梢king pin bush 主梢衬套knockout bar 脱模杵land 合模平坦面land area 合模面leader busher 导梢衬套lifting pin 起模顶销lining 内衬locating center punch 定位中心冲头locating pilot pin 定位导梢locating ring 定位环lock block 压块locking block 定位块locking plate 定位板loose bush 活动衬套making die 打印冲子manifold block 歧管档块master plate 靠模样板match plate 分型板mold base 塑料模座mold clamp 铸模紧固夹mold platen 模用板moving bolster 换模保持装置moving bolster plate 可动侧范本one piece casting 整体铸件parallel block 平行垫块paring line 分模线parting lock set 合模定位器pass guide 穴型导板peened head punch 镶入式冲头pilot pin 导销pin gate 针尖浇口plate 衬板pre extrusion punch 顶挤冲头punch 冲头puncher 推杆pusher pin 衬套梢rack 机架rapping rod 起模杆re-entrant mold 凹入模retainer pin 嵌件梢retainer plate 托料板return pin 回位梢riding stripper 浮动脱模器ring gate 环型浇口roller 滚筒runner 流道runner ejector set 流道顶出器runner lock pin 流道拉梢screw plug 头塞 set screw 固定螺丝shedder 脱模装置shim 分隔片shoe 模座之上下范本shoot 流道shoulder bolt 肩部螺丝skeleton 骨架slag riser 冒渣口slide(slide core) 滑块slip joint 滑配接头spacer block 间隔块spacer ring 间隔环 spider 模蕊支架spindle 主轴sprue 注道sprue bushing 注道衬套sprue bushing guide 注道导套sprue lock bushing 注道定位衬套sprue puller 注道拉料spue line 合模线square key 方键square nut 方螺帽square thread 方螺纹stop collar 限位套stop pin 止动梢stop ring 止动环stopper 定位停止梢straight pin 圆柱销stripper bolt 脱料螺栓stripper bushing 脱模衬套stripper plate 剥料板stroke end block 行程止梢submarine gate 潜入式浇口support pillar 支撑支柱/顶出支柱support pin 支撑梢supporting plate 托板sweep templete 造模刮板tab gate 辅助浇口taper key 推拔键taper pin 拔锥梢/锥形梢teeming 浇注three start screw 三条螺纹thrust pin 推力销tie bar 拉杵tunnel gate 隧道形浇口vent 通气孔wortle plate 拉丝范本模具常用之工作机械3D coordinate measurement 三次元量床boring machine 搪孔机cnc milling machine CNC铣床contouring machine 轮廓锯床copy grinding machine 仿形磨床copy lathe 仿形车床copy milling machine 仿形铣床copy shaping machine 仿形刨床cylindrical grinding machine 外圆磨床die spotting machine 合模机drilling machine 冲孔机engraving machine 雕刻机engraving E.D.M. 雕模放置加工机form grinding machine 成形磨床graphite machine 石墨加工机horizontal boring machine 卧式搪孔机horizontal machine center 卧式加工制造中心internal cylindrical machine 内圆磨床jig boring machine 冶具搪孔机jig grinding machine 冶具磨床lap machine 研磨机machine center 加工制造中心multi model miller 靠磨铣床NC drilling machine NC钻床NC grinding machine NC磨床 NC lathe NC车床NC programming system NC程序制作系统planer 龙门刨床profile grinding machine 投影磨床projection grinder 投影磨床radial drilling machine 旋臂钻床shaper 牛头刨床surface grinder 平面磨床try machine 试模机turret lathe 转塔车床universal tool grinding machine 万能工具磨床vertical machine center 立式加工制造中心wire E.D.M. 线割放电加工机具钢材alloy tool steel 合金工具钢aluminium alloy 铝合金钢bearing alloy 轴承合金blister steel 浸碳钢bonderized steel sheet 邦德防蚀钢板carbon tool steel 碳素工具钢clad sheet 被覆板clod work die steel 冷锻模用钢emery 金钢砂ferrostatic pressure 钢铁水静压力forging die steel 锻造模用钢galvanized steel sheet 镀锌铁板hard alloy steel 超硬合金钢high speed tool steel 高速度工具钢hot work die steel 热锻模用钢low alloy tool steel 特殊工具钢low manganese casting steel 低锰铸钢marging steel 马式体高强度热处理钢martrix alloy 马特里斯合金meehanite cast iron 米汉纳铸钢meehanite metal 米汉纳铁merchant iron 市售钢材molybdenum high speed steel 钼系高速钢molybdenum steel 钼钢 nickel chromium steel 镍铬钢prehardened steel 顶硬钢silicon steel sheet 硅钢板stainless steel 不锈钢tin plated steel sheet 镀锡铁板tough pitch copper 韧铜troostite 吐粒散铁tungsten steel 钨钢vinyl tapped steel sheet 塑料覆面钢板tap 攻牙表面处理关连用语age hardening 时效硬化ageing 老化处理air hardening 气体硬化air patenting 空气韧化annealing 退火anode effect 阳极效应anodizing 阳极氧化处理atomloy treatment 阿托木洛伊表面austempering 奥氏体等温淬火austenite 奥斯田体/奥氏体bainite 贝氏体banded structure 条纹状组织barrel plating 滚镀barrel tumbling 滚筒打光blackening 染黑法blue shortness 青熟脆性bonderizing 磷酸盐皮膜处理box annealing 箱型退火box carburizing 封箱渗碳bright electroplating 辉面电镀bright heat treatment 光辉热处理bypass heat treatment 旁路热处理carbide 炭化物carburized case depth 浸碳硬化深层carburizing 渗碳cementite 炭化铁chemical plating 化学电镀chemical vapor deposition 化学蒸镀coarsening 结晶粒粗大化coating 涂布被覆cold shortness 低温脆性comemtite 渗碳体controlled atmosphere 大气热处理corner effect 锐角效应creeping discharge 蠕缓放电decarburization 脱碳处理decarburizing 脱碳退火depth of hardening 硬化深层diffusion 扩散diffusion annealing 扩散退火electrolytic hardening 电解淬火embossing 压花etching 表面蚀刻ferrite 肥粒铁first stage annealing 第一段退火flame hardening 火焰硬化flame treatment 火焰处理full annealing 完全退火gaseous cyaniding 气体氧化法globular cementite 球状炭化铁grain size 结晶粒度granolite treatment 磷酸溶液热处理graphitizing 石墨退火hardenability 硬化性hardenability curve 硬化性曲线hardening 硬化heat treatment 热处理hot bath quenching 热浴淬火hot dipping 热浸镀induction hardening 高周波硬化ion carbonitriding 离子渗碳氮化ion carburizing 离子渗碳处理ion plating 离子电镀isothermal annealing 等温退火liquid honing 液体喷砂法low temperature annealing 低温退火malleablizing 可锻化退火martempering 麻回火处理martensite 马氏体/硬化铁炭metallikon 金属喷镀法metallizing 真空涂膜nitriding 氮化处理nitrocarburizing 软氮化normalizing 正常化oil quenching 油淬化overageing 过老化overheating 过热pearlite 针尖组织phosphating 磷酸盐皮膜处理physical vapor deposition 物理蒸镀plasma nitriding 离子氮化pre-annealing 预备退火precipitation 析出precipitation hardening 析出硬化press quenching 加压硬化process annealing 制程退火quench ageing 淬火老化quench hardening 淬火quenching crack 淬火裂痕quenching distortion 淬火变形quenching stress 淬火应力reconditioning 再调质recrystallization 再结晶red shortness 红热脆性residual stress 残留应力retained austenite 残留奥rust prevention 防蚀salt bath quenching 盐浴淬火sand blast 喷砂处理seasoning 时效处理second stage annealing 第二段退火secular distortion 经年变形segregation 偏析selective hardening 部分淬火shot blast 喷丸处理shot peening 珠击法single stage nitriding 等温渗氮sintering 烧结处理soaking 均热处理softening 软化退火solution treatment 固溶化热处理spheroidizing 球状化退火stabilizing treatment 安定化处理straightening annealing 矫直退火strain ageing 应变老化stress relieving annealing 应力消除退火subzero treatment 生冷处理supercooling 过冷surface hardening 表面硬化处理temper brittleness 回火脆性temper colour 回火颜色tempering 回火tempering crack 回火裂痕texture 咬花thermal refining 调质处理thermoechanical treatment 加工热处理time quenching 时间淬火transformation 变态tufftride process 软氮化处理under annealing 不完全退火vacuum carbonitriding 真空渗碳氮化vacuum carburizing 真空渗碳处理vacuum hardening 真空淬火vacuum heat treatment 真空热处理vacuum nitriding 真空氮化water quenching 水淬火wetout 浸润处理射出成形关联用语activator 活化剂bag moulding 气胎施压成形bonding strength 黏合强度breathing 排气caulking compound 填隙料cell 气孔cold slug 半凝式射出colorant 着色剂color matching 调色color masterbatch 色母料compound 混合料copolymer 共聚合体cull 残料废品cure 凝固化cryptometer 不透明度仪daylight 开隙dry cycle time 空料试车周期时间ductility 延性elastomer 弹性体extruded bead sealing 压出粒涂层法feed 供料filler 充填剂film blowing 薄膜吹制法floating platen 活动范本foaming agent 发泡剂gloss 光泽granule 颗粒料gunk 料斗hot mark 热斑hot stamping 烫印injection nozzle 射出喷嘴injection plunger 射出柱塞injection ram 射出冲柱isomer 同分异构物kneader 混合机leveling agent 匀涂剂lubricant 润滑剂matched die method 配合成形法mould clamping force 锁模力mould release agent 脱模剂nozzle 喷嘴oriented film 取向薄膜parison 吹气成形坏料pellet 粒料plasticizer 可塑剂plunger 压料柱塞porosity 孔隙率post cure 后固化premix 预混料purging 清除reciprocating screw 往复螺杆resilience 回弹性resin injection 树脂射出法rheology 流变学sheet 塑料片shot 注射shot cycle 射出循环slip agent 光滑剂take out device 取料装置tie bar 拉杆toggle type mould clamping system 肘杆式锁模装置torpedo spreader 鱼雷形分流板transparency 透明性void content 空洞率塑料原料acrylic 压克力casein 酪素cellulose acetate 醋酸纤维素CAcellulose acetate butyrate 醋酸丁酸纤维素CAB composite material 复合材料cresol resin 甲酚树脂CFdially phthalate 苯二甲酸二烯丙酯disperse reinforcement 分散性强化复合材料engineering plastics 工程塑料epoxy resin 环氧树脂EPethyl cellulose 乙基纤维素ethylene vinylacetate copolymer 乙烯-醋酸乙烯EVA ethylene-vinlacetate copolyme 醋酸乙烯共聚物EVA fiber reinforcement 纤维强化热固性/纤维强化复合材料high density polyethylene 高密度聚乙烯HDPEhigh impact polystyrene 高冲击聚苯乙烯HIPShigh impact polystyrene rigidity 高冲击性聚苯乙烯low density polyethylene 低密度聚乙烯LDPE melamine resin 三聚氰胺酚醛树脂MF nitrocellulose 硝酸纤维素phenolic resin 酚醛树脂plastic 塑料polyacrylic acid 聚丙烯酸PAPpolyamide 耐龙PApolybutyleneterephthalate 聚对苯二甲酸丁酯PBT polycarbonate 聚碳酸酯PCpolyethyleneglycol 聚乙二醇PFG polyethyleneoxide 聚氧化乙烯PEO polyethyleneterephthalate 聚乙醇对苯PETP polymetylmethacrylate 聚甲基丙烯酸甲酯PMMA polyoxymethylene 聚缩醛POMpolyphenylene oxide 聚硫化亚苯polyphenyleneoxide 聚苯醚PPOpolypropylene 聚丙烯PPpolystyrene 聚苯乙烯PS polytetrafluoroethylene 聚四氟乙烯PTFE polytetrafluoroethylene 聚四氟乙烯polythene 聚乙烯PEpolyurethane 聚氨基甲酸酯PU polyvinylacetate 聚醋酸乙烯PVAC polyvinylalcohol 聚乙烯醇PVA polyvinylbutyral 聚乙烯醇缩丁醛PVB polyvinylchloride 聚氯乙烯PVC polyvinylfuoride 聚氟乙烯PVF polyvinylidenechloride 聚偏二氯乙烯PVDC prepolymer 预聚物silicone resin 硅树脂thermoplastic 热塑性thermosetting 热固性thermosetting plastic 塑料unsaturated polyester 不饱和聚酯树脂成形不良用语aberration 色差bite 咬入blacking hole 涂料孔(铸疵)blacking scab 涂料疤blister 起泡blooming 起霜blow hole 破孔blushing 泛白body wrinkle 侧壁皱纹breaking-in 冒口带肉bubble 膜泡burn mark 糊斑burr 毛边camber 翘曲cell 气泡center buckle 表面中部波皱check 细裂痕checking 龟裂chipping 修整表面缺陷clamp-off 铸件凹痕collapse 塌陷color mottle 色斑corrosion 腐蚀crack 裂痕crazing 碎裂crazing 龟裂deformation 变形edge 切边碎片edge crack 裂边fading 退色filler speak 填充料斑fissure 裂纹flange wrinkle 凸缘起皱flaw 刮伤flow mark 流痕galling 毛边glazing 光滑gloss 光泽grease pits 污斑grinding defect 磨痕haircrack 发裂haze 雾度incrustation 水锈indentation 压痕internal porosity 内部气孔mismatch 偏模mottle 斑点necking 缩颈nick 割痕range peel 橘皮状表面缺陷overflow 溢流peeling 剥离pit 坑pitting corrosion 点状腐蚀plate mark 范本印痕pock 麻点pock mark 痘斑resin streak 树脂流纹resin wear 树脂脱落riding 凹陷sagging 松垂saponification 皂化scar 疤痕scrap 废料scrap jam 废料阻塞scratch 刮伤/划痕scuffing 深冲表面划伤seam 裂痕shock line 模口挤痕short shot 充填不足shrinkage pool 凹孔sink mark 凹痕skin inclusion 表皮折迭straightening 矫直streak 条状痕surface check 表面裂痕surface roughening橘皮状表皮皱折surging 波动torsion 扭曲warpage 翘曲waviness 波痕webbing 熔塌weld mark 焊痕whitening 白化wrinkle 皱纹模具常用刀具工作法用语adjustable spanner 活动扳手angle cutter 角铣刀arbour 心轴backing 衬垫belt sander 带式打磨机buffing 抛光chamfering machine 倒角机chamfering tool 去角刀具chisel 扁錾chuck 夹具compass 两角规concave cutter 凹面铣刀convex cutter 凸形铣刀cross joint 十字接头cutting edge clearance 刃口余隙角drill stand 钻台edge file 刃用锉刀file 锉刀flange joint 凸缘接头grinder 砂轮机hammer 铁锤hand brace 手摇钻hatching 剖面线hexagon headed bolt 六角头螺栓hexagon nut 六角螺帽index head 分度头jack 千斤顶jig 治具kit 工具箱lapping 研磨metal saw 金工锯nose angle 刀角pinchers 钳子pliers 铗钳 plug 柱塞头polisher 磨光器protable driller 手提钻孔机punch 冲头sand paper 砂纸scraper 刮刀screw driver 螺丝起子scribing 划线second out file 中纹锉spanner 扳手spline broach 方栓槽拉刀square 直角尺square sleeker 方形镘刀square trowel 直角度stripping 剥离工具T-slot T形槽tool for lathe 车刀tool point angle 刀刃角tool post 刀架tosecan 划线盘trimming 去毛边waffle die flattening 压纹效平wiper 脱模钳wrench 螺旋扳手各种冲模加工关连用语barreling 滚光加工belling 压凸加工bending 弯曲加工blanking 下料加工bulging 撑压加工burring 冲缘加工cam die bending 凸轮弯曲加工coining 压印加工compressing 压缩加工compression bending 押弯曲加工crowning 凸面加工curl bending 卷边弯曲加工curling 卷曲加工cutting 切削加工dinking 切断蕊骨double shearing 迭板裁断drawing 引伸加工drawing with ironing 抽引光滑加工embossing 浮花压制加工extrusion 挤制加工filing 锉削加工fine blanking 精密下料加工finish blanking 光制下料加工finishing 精整加工flanging 凸缘加工folding 折边弯曲加工folding 折迭加工forming 成形加工impact extrusion 冲击挤压加工indenting 压痕加工ironing 引缩加工knurling 滚花lock seaming 固定接合louvering 百叶窗板加工marking 刻印加工necking 颈缩加工notching 冲口加工parting 分断加工piercing 冲孔加工progressive bending 连续弯曲加工progressive blanking 连续下料加工progressive drawing 连续引伸加工progressive forming 连续成形加工reaming 铰孔加工restriking 二次精冲加工riveting 铆接加工roll bending 滚筒弯曲加工roll finishing 滚压加工rolling 压延加工roughing 粗加工scrapless machining 无废料加工seaming 折弯重迭加工shaving 缺口修整加工shearing 切断加工sizing 精压加工/矫正加工slitting 割缝加工spinning 卷边?接stamping 锻压加工swaging 挤锻压加工trimming 整缘加工upsetting 锻粗加工wiring 抽线加工冲压机械及周边关连用语back shaft 支撑轴blank determination 胚料展开bottom slide press 下传动式压力机board drop hammer 板落锤brake 煞车 buckle 剥砂面camlachie cramp 铸包chamotte sand 烧磨砂charging hopper 加料漏斗clearance 间隙closed-die forging 合模锻造clump 夹紧clutch 离合器clutch brake 离合器制动器clutch boss 离合器轮壳clutch lining 离合器覆盖coil car 带卷升降运输机coil cradle 卷材进料装置coil reel stand 钢材卷料架column 圆柱connection screw 连杆调节螺钉core compound 砂心黏结剂counter blow hammer 对击锻锤cradle 送料架crank 曲柄轴crankless 无曲柄式cross crank 横向曲轴cushion 缓冲depression 外缩凹孔dial feed 分度送料die approach 模口角度die assembly 合模die cushion 模具缓冲垫die height 冲压闭合高度die life 模具寿命die opening 母模逃孔die spotting press 调整冲模用压力机double crank press 双曲柄轴冲床draght angle 逃料倾斜角edging 边锻伸embedded core 加装砂心feed length 送料长度feed level 送料高度filling core 埋入砂心filling in 填砂film play 液面花纹fine blanking press 精密下料冲床forging roll 辊锻机finishing slag 炼后熔渣fly wheel 飞轮fly wheel brake 飞轮制动器foot press 脚踏冲床formboard 进模口板frame 床身机架friction 摩擦friction brake 摩擦煞车gap shear 凹口剪床gear 齿轮gib 滑块引导部gripper 夹具gripper feed 夹持进料gripper feeder 夹紧传送装置hammer 槌机hand press 手动冲床hand rack pinion press 手动齿轮齿条式冲床hand screw press 手动螺旋式冲床hopper feed 料斗送料idle stage Idle Station 空站inching 微调尺寸isothermal forging 恒温锻造key clutch 键槽离合器knockout 脱模装置knuckle mechanic 转向机构land 模具直线刀面部loader 供料器 unloader 卸料机loop controller 闭回路控制器lower die 下模micro inching device 微寸动装置microinching equipment 微动装置moving bolster 活动工作台notching press 冲缺口压力机opening 排料逃孔overload protection device 防超载装置pinch roll 导正滚轮pinion 小齿轮pitch 节距pressfit 压入progressive 连续送料pusher feed 推杆式送料pusher feeder 料片押片装置quick die change system 快速换模系统regrinding 再次研磨releasing 松释动作reversed blanking 反转下料robot 机器人roll forming machine 辊轧成形roll forming machine 辊轧成形机roll release 脱辊roller feed 辊式送料roller leveler 辊式矫直机rotary bender 卷弯成形机safety guard 安全保护装置scrap cutter 废料切刀scrap press 废料冲床。
机械工程专业英语Unit 4
❖ One of the basic operations of hammer forging is the elongation of a piece of metal by stretching with hammer blows, causing it to become thinner and longer. 锤锻中常用开式模锻。在锤锻中零件通过锤击辅之以相对简单的 工具成型。其中包括开式锻模。锤锻的基本操作之一就是通过锤击使 金属伸长，促成其变细变长。
❖ Advantage：can produce components Байду номын сангаасf greater complexity and accuracy, with a better surface finish, than the more traditional methods not using closed dies. 优点：闭式模锻能生产高度复杂和精确的零件，而且表面光洁度要 比不用闭式锻模的更传统方法好。
它们均利用下落重量来产生金属成型所需的压力。锻造大零件则要 用到蒸汽、压缩空气、液压或电力驱动的锻压机。大型的自动化锻机用 于工程零件的批量生产。
open-die forging &closed-die forging 开式锻模和闭式锻模
1. open-die forging 开式锻模
❖ open-die forging, usually in the form of hammer forging.
Unit 4 Forging Processes
- 1、下载文档前请自行甄别文档内容的完整性，平台不提供额外的编辑、内容补充、找答案等附加服务。
- 2、"仅部分预览"的文档,不可在线预览部分如存在完整性等问题,可反馈申请退款(可完整预览的文档不适用该条件!)。
- 3、如文档侵犯您的权益，请联系客服反馈,我们会尽快为您处理(人工客服工作时间：9:00-18:30)。
锻压 forging and stamping金属塑性加工 metal plastic working金属压力加工 mechanical metal working体积成形 bulk forming锻造 forging / hot forging锻造技术 forging technology / forging technique锻造工艺 forging technology / forging process锻工 forger / blacksmith / hammer man / hammer smith / hammerer塑性 plasticity超塑性 superplasticity可锻性 forgeability切削性能 machinability最小阻力定律 the law of minimum resistance体积不变条件 constance(y) of volume / incompressibility锻造流线 grain flow / forging flow line滑移线 sliding line / slip-line中国机械工程学会锻压学会 Forging and stamping Institution of CMES 中国锻造协会 China Forging Industry Association第一汽车制造厂锻造厂 First Automobile Works , Forging Plant原材料及下料原材料 raw material / material棒料 bar毛坯 billet / blank / stock / bar stock坯料 perform / preform slug / blank / stock / billet下料 cropping / shearing剪切下料 cropping / shearing热切 hot cropping / hot shearing冷切 cold cropping / cold shearing锯切下料 sawing带锯下料 band sawing圆盘锯下料 circular sawing冷折下料 nicking and breaking热剁下料 hot cropping气割 gas cutting / oxygen-acetylene cutting电弧切割 electric-arc cutting / arc cutting精密剪切 precision cropping / precision shearing钢号、牌号 grade of steel规格 specification炉号 heat number / cast number / batch number钢号代码 heat code / cast code批号 batch number技术条件 technical conditions / technical provisions / specification普通长度 normal length倍尺长度 multiple length定尺长度 specified length / fixed length周期型钢 periodic section steel品质证明书 certificate of quality代用料 substitute material代用标记 substitute mark毛坯重量 billet weight重量公差 weight tolerance毛坯长度 billet length长度公差 length tolerance料头 stub bar材料利用率 material utilization毛坯加热锻造温度范围 forging temperature interval / forging temperature range 始锻温度 starting forging temperature终锻温度 final forging temperature加热温度 heating temperature炉温 furnace temperature保温时间 hold(ing) time / dwelling time / soaking time保温 soaking火次 heating number过热 over heat过烧 burning烧损、火耗 scale loss / heating loss氧化铁皮、氧化皮 scale / oxide skin加热炉 heating furnace火焰加热 flame heating火焰炉 flame furnace推杆式炉、半连续炉 pusher furnace装料、上料 loading出料、卸料 unloading室式炉、箱式炉 batch-type furnace转底炉 rotary hearth furnace转体炉 rotary body furnace电加热 electric heating感应加热 induction heating电阻炉 electric resistance furnace少无氧化加热 scale-less or free heating反射炉 reverberating furnace模锻模锻 die forging / closed-die forging / impression die forging开式模锻 closed-die forging / impression die forging闭式模锻 no-flash die forging / flashless die forging锤模锻 closed-die forging / impression die forging / drop forging / stamping 锻压机模锻 mechanical press forging平锻 upsetting / heading无飞边模锻 no-flash forging无拔模斜度模锻 no-draft forging模锻件 forging / workpiece锻件重量 forging weight普通锻件 conventional forging精确（公差）锻件 close-tolerance forging锻造工序卡 forging process chart工序 operation / process / procedure工步 process step打击 blow / strike锻件图 forging drawing加工余量 machining allowance镦锻、顶锻 upsetting / heading镦粗 upsetting压扁 flattening去氧化皮 scale-breaking拔长工步 drawing / elongating / fullering拔夹钳头 tong-hold drawn / tagging滚压工步 edging / edge rolling / gathering弯曲工步 bending制坯工步 pre-forming平锻聚料 gathering / pushing up / upsetting锥形镦粗 taper upsetting / coning粗（初）锻 blocker-type forging预锻 pre-forging / blocking终锻 finish-forging返回锻模校正 re-striking分模线 parting line模锻斜度、拔模角、拔模斜度 draft angle外拔模角 outside draft内拔模角 inside draft自然拔模角 natural draft相配拔模角 matching draft外圆角 corner内圆角 fillet未注明圆角 all radii not specified尺寸按交点注 all dimensions specified form intersections模锻方案 forging form一料多件 multi-forging on one billet (bar)一模两件 two at a time一模多件 multi at a time调头锻 turn-end forging一火多件 multi-forging in one heat打零件号、炉号码及模具号处 raise part No. heat code and die No. here 除注明处外 unless otherwise noted冲孔、切边、校正冲连皮 punching the wad / punching the slug冲孔 pierce盲孔 non-penetrated hole / blind hole连皮 wad / recess / slug切边 clipping / trimming飞边 flash残余飞边、残余飞刺 flash extension / residual flash切边线、飞边线 flash line / trim line整形 forming to size校平 flattening / planishing校直 straightening精压、压印 coining / sizing校正 sizing / setting冷校正 cold sizing / cold setting模具及工具锻模 forging die锤锻模 hammer forging die模块 die block上模 top die / upper die下模 bottom die平模 flat die模膛、型槽 impression / cavity单模膛锻模 single-impression die多模膛锻模 multi-impression die制坯模膛 blanking impression镦粗台 upset place / upset die拔长模膛 drawing impression拔长台 drawing face压扁台 flattening face滚压模膛 edging impression / gathering impression /edger弯曲模膛 bending impression / bender成形模膛 forming impression卡压模膛 fullering impression模锻模膛 die forging impression劈开台 cleaver divider / splitter预锻模膛 blocking impression / blocker / mould impression预错 misalignment / pre-mismatch粗（初）锻模膛 buster / rougher / blocker / pre-blocking impression终锻模膛 finisher / finishing impression切断模膛 cutter / cut off飞边槽 flash cavity飞边桥 flash land / flash saddle飞边仓 flash gutter / gutter飞边桥厚度、飞边桥深度 flash land depth / flash saddle depth飞边桥宽度 flash land width / flash saddle width波纹飞边 corrugated flash阻力沟 resistance slot热锻件图 hot forging drawing收缩率 contraction / shrink scale热尺寸 hot dimensions边缘半径 edge R(radius)锁扣 lock圆形锁扣 circular lock侧锁扣 lateral lock止推锁扣 counter lock纵向锁扣 sideway(s) lock角锁扣 corner lock分模面 parting area / die parting face / parting plane承击面 die contact area / beating area / striking surface / cushion face / die face / kissing face燕尾 shank / dovetail燕尾中心线 centre line of dovetail键槽 keyway键槽中心线 centre line of keyway钳口 gate浇口 sprue浇道 runner检验角、检验面 match edge /match line / setting edge(face)起重孔 handling hole锻模中心 center of forging die模膛中心 center of impression(cavity)模膛排列、型槽布排 arrangement of impression(cavity)过渡模座 intermediate die socket平锻模 upset forging die平锻凹模 grip die / grooved die平锻活动模 movable die平锻固定模 stationary die平锻冲头、平锻凸模 punch / heading tool凸模柄 punch shank凸模镶块 punch insert凹模镶块 die insert积聚模膛 gathering impression穿孔模膛 piercing impression切边模膛 trimming impression卡细模膛 necking impression扩径模膛 expanding impression凸模固定器 punch holder / heading tool holder定料板、前挡板 stock gage(gauge) / gauge plate后挡板 back-plate / rear slop塞子 core排气孔 vent-hole / air vent模座 bolster镶块模、镶块 inserted forging die / die insert应力圈 shrink ring导套 guide bushing导柱 pillar / guide pin顶杆 ejector / knockout pin压板、压块 clamp / clamp block垫板 plate / pedestal plate / wearing plate切边模 trimming die冲孔模 piercing die冷锻件图 cold forging drawing凹模 die凸模、冲头 punch切边冲头、切边凸模 trimmer punch / punch凸模固定块 punch holder切边凹模、切边刃口 trimmer blade(s) / blade(s)凹模座 blade(s) shoe冲孔定位凹模 nest die复合模 compound die联合模 progressive die卸料板 stripper校正模 sizing die / straightening die精压模、压印模 coining die / sizing die辊锻模 rolling die辊锻扇形块 die segment / rolling segment模具的补焊修复 weld repair of die模具翻新加工、模具翻新 re-sinking and reworking of die模具寿命 die life检验用铸件（浇盐件）die proof for inspection / casting pattern for inspection模型 master / plaster / pattern / model样板 template / former楔 key键 dowel / locking pin / locking key模具闭合高度 shut height翻新后最小闭合高度 minimum shut height锻造公差、锻造缺陷及检查锻造公差 forging tolerance / tolerance for impression die forging 确定公差的因素 information required in determining tolerance锻件形状复杂系数 shape complexity factor of forging材质系数 difficulty of material分模线形状 shape of die line公差等级 tolerance grad锻件公称尺寸 nominal dimension of forging厚度公差 thickness tolerance模具闭合公差 die closure tolerance长度、宽度、高度公差 length 、width and height tolerance模具磨损公差 die wear tolerance错差、错差公差 mismatch / match tolerance中心距公差 tolerance for centre to centre dimensions平面度公差 platness tolerance直线度公差 straightness tolerance残余飞边及切入深度公差 residual flash and trimmed flat tolerance 顶杆压痕公差 ejector mark tolerance表面缺陷公差 surface tolerance壁厚差 difference in wall thickness冲孔公差 pierced hole tolerance同轴度公差 axiality tolerance折叠、折纹 lap / overlap / fold缺肉、未充满 under-fill模锻不足 under-pressing表面缺陷 surface imperfection氧化皮坑 scale pit变形 distortion / deformation毛刺、飞刺 burr / fin凹陷 void出气孔金属柱 vent plug偏心 eccentricity中间检查 intermediate inspection流动检查 patrol inspection外观检查 visual inspection最后检查 final inspection抽检 random inspection其他锻造方法多向模锻 multi-ram forging / multidirectional die forging 精密模锻 precision forging闭塞模锻 croe forging合锻combination forging挤压锻造 extrusion forging挤压 extrusion正挤压 forward extrusion / direct extrusion反挤压 backward extrusion / indirect extrusion复合挤压 combined extrusion辊锻 roll forging / reducer rolling制坯辊锻 roll forging of blank成形辊锻 finishing roll forging辗环 ring rolling楔横轧 cross wedge rolling / transverse rolling超塑成形 superplastic forming等温锻造 isothermal forging冷锻 cold forging温锻 warm forging无屑加工 chipless working粉末锻造 powder metal forging / powder forging液态模锻 melted metal squeezing电热镦 electric upset forging摆辗 swing-rolling / rock rolling / tambling转动辗压 turn-rolling / rotary-rolling径向锻造 radial forging自由锻自由锻 open die forging / flat die forging胎模锻 loose tooling forging送进量 feed延伸系数 coefficient of stretching高径比 ratio of height to diameter锻造比 forging ratio镦粗 upsetting局部镦粗 local upsetting拔长 drawing out / stretching / swaging / fullering芯棒拔长 drawing out with the core bar滚圆、摔圆 rolling倒棱 chamfering压痕、克印 indentation压肩 necking错料 offset弯曲 bending扭转 twisting切割、切断 cutting冲孔 punching / piercing扩孔 expanding冲头扩孔 expanding with a punch马杠扩孔、码圈 saddle forging / saddling锻接 forging welding空冷 air cooling堆冷 cooling in heap(pile)坑冷 cooling in hole(box、pit)灰砂冷 cooling in dust or sand炉冷 furnace cooling塌角 rollover / shear droop龟裂 crazing角裂 chink中心裂纹 chevron crack发纹 hairline cracks / hair-crack铁砧 anvil花砧 swage block冲子 punch剁刀 triangular chisel摔子 tups / swager / swaging die胎模 loose tooling马架 mandrel supporter芯轴、马杠 mandrel手锤 hand hammer大锤 sledge hammer夹钳 tong自紧吊钳 self closing crane tong锻压设备及装置锻锤 forging hammer落锤 drop hammer单作用锤 drop hammer双作用锤 double-action hammer重力落锤 gravity-drop hammer夹板锤 board drop hammer / board drop gravity hammer 皮带锤 belt drop hammer链条锤 chain drop hammer模锻锤 die forging hammer蒸汽-空气模锻锤 steam or air dir forging hammer锤头 ram砧座 anvil-block下砧座、砧套、夹持器 anvil cap / sow block对击锤 counter-blow hammer高速锤 high energy rate forging hammer液压机 hydraulic press快速锻造液压机 high speed forging hydraulic press机械压力机 mechanical press曲柄压力机 crank press热模锻压力机、锻压机 forging press楔式锻压机 wedge-tyoe mechanical press开式压力机 c-frame press / gap frame press闭式压力机 straight side press单点压力机 single point press双点压力机 two point press单动压力机 single action press双动压力机 double action press滑块 slide / ram导轨 guide工作台 table / bed顶出器 ejector平锻机 horizontal forging machine / forging machine / upsetter切边压力机 trimming press校正压力机 restriking press精压机、肘杆式精压机 coining press / knuckle joint coining press液压曲柄扭转机、扭转机 hydraulic twister for crank-shaft / twister多工位自动热锻机multistage automatic hot forging machine / automatic forging-pressing machine哈德堡热成形机 HATEBUR metal-forming equipment / HATEBUR hotmatic螺旋压力机 screw press摩擦压力机 friction screw press液压螺旋压力机 hydraulic screw press径向锻轴机 radial forging machineGFM自动模锻机 GFM automatic die forging machine感应抛丸机 stress abrator抛丸清理室 shot blasting cleaning chamber抛丸机 wheel abrator / throw shot machine喷丸机 shot blasting machine / peening machine起重机 crane桥式起重机 overhead traveling crane / bridge type crane塔式起重机 tower crane起重葫芦 hoist电动葫芦 electric hoist气动葫芦 pneumatic hoist磁粉探伤机 magnetic particle detector荧光磁粉探伤机 fluorescent magnetic particle detector无损探伤机 non-destructive inspection machine硬度计 hardness tester布式硬度计 Brinell hardness tester洛式硬度计 Rockwell hardness tester金属材料试验机 metallic material testing machine非金属材料试验机 non-metallic material testing machine拉力试验机 tensile testing machine压力试验机 compression testing machine扭转试验机 torsion testing machine疲劳试验机 fatigue testing machine冲击试验机 impact testing machine弯折试验机 reverse bend tester显微镜 microscope金相显微镜 metallographic microscope试样（样品） specimen辊锻机 forging roll扩孔机 ring rolling machine瓦格纳环轧机 WAGNER ring roll摆辗机 rotary forging press快速换模装置 quick die change device换模翻转装置 tool changing and turnover fixture锻造自动线 automated forging line机械手 manipulator / mechanical hand / mechanical operated arm 除氧化皮装置 descaler高压水去氧化皮 high pressure hydro-peening传送装置 transfer equipment悬挂输送链 suspension conveyer chain链式传送带 chain conveyer板式传送带 pallet conveyer毛坯滑道 stock guide工件箱 parts gondola / work bin飞边箱 flash gondola / flash bin型号 type / model公称压力 capacity / nominal force锻造吨位 forging tonnage落下部分重量 droping weight / weight of falling每分钟打击次数 blow per minute / strick per minute打击速度 blow speed打击效率 blow efficiency滑块行程stroke of ram行程次数 number of stroke滑块行程调节量 adjustment of ram stroke下死点 lower dead point / bottom dead centre上死点 upper dead point / top dead centre寸动 inching最大装模高度 maximum die set height最大封闭高度 maximum shut height空气锤 pneumatic hammer / air hammer锻件热处理锻件热处理 forging heat-treatment加热规范 heating schedule正火 normalizing淬火 quench-hardening / hardening / quenching回火 tempering调质 quenching and tempering / hardening and tempering 退火 annealing等温退火 isothermal annealing形变热处理 thermomechanical treatment (TMT)锻件余热淬火 quenching from forging heat残余应力 residual stress消除残余应力 stress relieving淬火裂纹 quenching crack / hardening flaw淬火应力 quenching stress / hardening stress淬火介质 quenching medium拉长淬火机 stretch-quench machine硬度 hardness布式硬度试验 Brinell hardness test / Brinelling洛式硬度试验 Rockwell hardness test锻件清理抛丸清理 shot-blasting / peening抛丸室（机） shot-blast chamber(machine)喷砂清理 sand blast cleaning酸洗 pickling / dipping滚筒清理 tumbling / roller cleaning磨毛刺 grinding / burring设备分类工艺设备 manufacturing equipment标准设备 standard equipment非标准设备 non-standard equipment通用设备 vniversal equipment专用设备 special equipment热处理设备 heat treatment equipment热处理主要设备 main equipment for heat treatment热处理辅助设备 auxiliary equipment for heat treatment热处理成套设备（热处理生产线） complete set of heat treatment equipment 热处理炉 heat treatment furnace燃料炉 fuel-fired furnace燃气炉 gas-fired furnace燃油炉 oil-fired furnace燃煤炉 coal-fired furnace电热设备 electro-heat installation电热装置 electro-heat equipment工作温度 working temperature工作区尺寸 working space dimensions生产率 production rate额定温度 rated temperature炉温自动控制 automatic control of furnace temperature炉温程序控制 program control of furnace temperature炉温的时间比例控制 time ratio control of furnace temperature风室 wind chamber连续式炉 continuous furnace多区域炉 multi-zone furnace感应加热设备表面加热 surface heating感应加热 induction heating工频 mains frequency低频 low frequency中频 medium frequency超音频 ultrasonic frequency高频 high frequency超高频 ultrahigh frequency感应加热设备 induction heating equipmen。