注塑行业术语中英对照表(已打)
注塑常用术语英文表达
1.雾气Moisture Streaks2.玻纤分配不均Glass Fiber Streaks3.困气Gas Trap Effect4.银丝纹Sliver Marks5.结合线Weld Line6.水波痕Water Wave Effect7.黑点Dark Sport8.顶出印Visible Ejector Marks9.变形Deformation During Demolding10.填充不足Short Filling11.冷料流痕Cold Slug12.进胶口点不良Dull Spots Near The Sprue13.喷射痕Jetting14.表面起层Flaking Of The Surface Layer15.浮泡Entrapped Air16.过热变色Burnt Streaks17.龟裂Stress Crack18.缩水痕Sink Marks19.真空气泡Density Bubble20.披锋Flash21.擦伤印Scratch MarksGlass fiber rich surface/glass emergence on the surface22 尺寸过大Over dimension23 尺寸过小Under dimension24 翘曲Warpage/warped25 收缩Shrinkage/shrink26 缩影Sink marks27 打不满Short shot/short molding塑料模具mould of plastics注塑模具injection mould冲压模具die模架 mould base定模座板 Top clamping plateTop plateFixed clamp plate水口推板stripper plateA 板 A plateB 板 B plate支承板support plate方铁spacer plate底针板ejector plate面针板ejector retainer plate回针Return pin导柱Guide pin有托导套Shoulder Guide bush直导套Straight Guide bush动模座板 Bottom clamp plate Moving clamp plate基准线 datum line基准面 datum plan型芯固定板core-retainer plate凸模固定板punch-retainer plate顶针 ejector pin单腔模具single cavity mould多腔模具multi-cavity mould多浇口 multi-gating浇口 gate缺料 starving排气 breathing光泽 gloss合模力 mould clamping force锁模力 mould locking force挤出 extrusion开裂 crack循环时间cycle time老化 aging螺杆 screw麻点 pit嵌件 insert活动镶件movable insert起垩 chalking浇注系统feed system主流道sprue分流道 runner浇口 gate直浇口 direct gate , sprue gate轮辐浇口spoke gate , spider gate点浇口 pin-point gate测浇口 edge gate潜伏浇口submarine gate , tunnel gate 料穴 cold-slug well浇口套 sprue bush流道板 runner plate排飞槽 vent分型线（面） parting line定模 stationary mould ， Fixed mould 动模 movable mould, movable half上模 upper mould ， upper half下模 lower mould ， lower half型腔 cavity凹模 cavity plate ， cavity block拼块 split定位销 dowel定位销孔dowel hole型芯 core斜销 angle pin, finger cam滑块 slide滑块导板slide guide strip楔紧块 heel block, wedge lock拉料杆 sprue puller定位环 locating ring冷却通 cooling channel脱模斜度draft滑动型芯slide core螺纹型芯threaded core热流道模具hot-runner mould绝热流道模insulated runner mould熔合纹 weld line（flow line）三板式模具three plate mould脱模 ejection换模腔模具interchangeable cavity mould 脱模剂 release agent注射能力shot capacity注射速率injection rate注射压力injection pressure差色剂 colorant保压时间holdup time闭模时间closing time定型装置sizing system阴模 female mould ， cavity block阳模 male mould电加工设备Electron Discharge Machining数控加工中心CNC machine center万能铁床 Universal milling machine卧式刨床 Horizontal planer车床 Engine lathe平面磨床Surface grinding machine去磁机 Demagnetization machine万能摇臂钻床Universal radial movable driller 立式钻床 Vertical driller超声波清洗机Ultrasonic clearing machine。
（精编）模具注塑术语中英文对照
（精编）模具注塑术语中英文对照(精编)模具注塑术语中英文对照根据国家标准，以下为部分塑料模具成形术语的标准翻译。
动模MovableMouldMovingHalf定模座板FixedClampPlateTopClampingPlateTopPlate动模座板MovingClampPlateBottomClampingPlateBottomPlate上模座板UpperClampingPlate下模座板LowerClampingPlate凹模固定板Cavity-retainerPlate 型芯固定板MouldCore-retainerPlate凸模固定板Punch-retainerPlate模套DieBodyDieSleeveDieBlank支承板BackingPlateSupportPlate垫块SpacerParallel支架EjectorHousingMouldBaseLeg模头DieHead模具分类8InjectionMold注塑模PlasticRubberMould塑胶模RubberMolding橡胶成形HotChamberDieCasting热室压铸SandMoldCasting砂模铸造ExtrusionMold挤出模Multi-CavityMold多模穴模具PalletizingDie叠层模PlasterMold石膏模ThreePlatesMold三板模PlainDie简易模PierceDie冲孔模FormingDie成型模ProgressiveDie连续模GangDies复合模ShearingDie剪边模CavityDie型腔模RivetingDie铆合模CompressionMolding压缩成型FlashMold溢流式模具ExtrusionMold挤压式模具SplitMold分割式模具MouldCavity型腔母模MoldCore模芯公模LargeDieMold大型模具PreciseDieMold 精密模具ComplexDieMold复杂模具FoamingMould发泡模具MetalDie金属模具PlasticMold塑料模具ToolStampingDiePunchDie冲压模具ExtrusionDie挤压模具GraphiteDie石墨模具流道浇口部分RunnerSystem浇道系统SprueColdMaterialTrap浇道冷料井SpruePuller拉杆RunnerDesign流道设计MainRunner主流道SecondaryRunner 次流道MouldGateDesign浇口设计SubmarineGate潜伏浇口TunnelGate隧道式浇口PinpointGate点浇口FanGate扇形浇口SideGate侧浇口EdgeGate侧缘浇口TabGate 搭接浇口FilmGate薄膜浇口FlashGate闸门浇口SlitGate缝隙浇口DishGate盘形浇口DiaphragmGate隔膜浇口RingGate环形浇口Runnerless无浇道Sprueless无射料管方式LongNozzle延长喷嘴方式Sprue浇口，溶渣Insulated/HotRunner热浇道RunnerPlat 浇道模块ValveGate阀门浇口SlagWell冷料井ColdSlag冷料渣SprueGate射料浇口Nozzle 射嘴SprueLockPin料头钩销（拉料杆）注塑缺陷Flash飞边Warpage翘曲AirTrap积风Blush发赤FlowLine流痕Splay银纹ShortShot 短射SinkMark缩痕Streak条纹Void缩孔WeldLine熔接线GasMark烧焦ColdSlug冷斑Delamination起皮Burr毛刺FlawScratch刮伤Gloss光泽Glazing光滑SurfaceCheck表面裂痕Hesitation迟滞注塑工艺MoldingConditions成型条件Drying烘干BarrelTemperature 料筒温度MeltTemperature熔化温度MoldTemperature模具温度InjectionPressure注塑压力BackPressure背压InjectionSpeed注塑速度ScrewSpeed螺杆转速TensileStrength抗拉强度T ensileElongation延伸率FlexuralModulus弯曲模FlexuralStrength抗弯强度Shrinkage收缩率RegrindUsage次料使用Moulding模塑机械设备Lathe车床Planer刨床Miller/MillingMachine铣床Grinder磨床Driller钻床LinearCutting线切割ElectricalSparkle电火花Welder电焊机PunchingMachine冲床Robot机械手CommonEquipment 常用设备EDMElectronDischargeMachining放电加工3DCoordinateMeasurement三次元量床BoringMachine搪孔机ContouringMachine轮廓锯床CopyGrindingMachine仿形磨床CylindricalGrindingMachine外圆磨床DieSpottingMachine合模机EngravingMachine 雕刻机EngravingE.D.M雕模放置加工机FormGrindingMachine成形磨床GraphiteMachine石墨加工机HorizontalBoringMachine卧式搪孔机HorizontalMachineCenter卧式加工制造中心InternalCylindricalMachine内圆磨床模具零件TopPlate上托板（顶板）T opBlock上垫脚PunchSet上模座PunchPad上垫板PunchHolder上夹板StripperPad脱料背板UpStripper上脱料板MaleDie公模（凸模）FeatureDie公母模FemaleDie母模（凹模）UpperMoldPlate上模板LowerMoldPlate 下模板DiePad下垫板DieHolder下夹板DieSet下模座BottomBlock下垫脚BottomPlate下托板（底板）StrippingPlate内外打（脱料板）OuterStripper外脱料板InnerStripper内脱料板LowerStripper下脱料板InnerGuidingPost 内导柱InnerHexagonScrew内六角螺钉DowelPin固定销MouldCoilSpring模具弹簧LifterPin 顶料销IsoheightSleeve等高套筒Pin销LifterGuidePin浮升导料销GuidePin导正销WireSpring圆线弹簧OuterGuidingPost外导柱StopScrew止付螺丝LocatedPin定位销OuterBush外导套Punch冲头Insert入块（嵌入件）DeburringPunch压毛边冲子GroovePunch压线冲子StampedPunch字模冲子RoundPunch圆冲子SpecialShapePunch 异形冲子BendingBlock折刀Roller滚轴BafflePlate挡块LocatedBlock定位块SupportingBlockforLocation定位支承块AirCushionPlate气垫板Air-CushionEject-rod 气垫顶杆TrimmingPunch切边冲子StiffeningRibPunchStinger加强筋冲子RibbonPunch压筋冲子Reel-stretchPunch卷圆压平冲子GuidePlate定位板SlidingBlock滑块SlidingDowelBlock滑块固定块ActivePlate活动板LowerSlidingPlate 下滑块板UpperHolderBlock上压块UpperMidPlate上中间板SpringBox弹簧箱Spring-BoxEject-rod弹簧箱顶杆Spring-BoxEjec模具技术用语各种常用模具成形方式AccurateDieCasting精密压铸PowderForming粉末成形CalendaringMolding压延成形PowderMetalForging粉末锻造ColdChamberDieCasting冷式压铸PrecisionForging 精密锻造ColdForging冷锻PressForgingstampforging冲锻CompactingMolding粉末压出成形RockingDieForging摇动锻造CompoundMolding复合成形RotaryForging回转锻造CompressionMolding压缩成形RotationalMolding离心成形DipMold浸渍成形RubberMolding橡胶成形EncapsulationMolding注入成形SandMoldCasting砂模铸造ExtrusionMolding挤出成形ShellCasting壳模铸造FoamForming 发泡成形SinterForging烧结锻造ForgingRoll轧锻SixSidesForging 六面锻造GravityCasting重力铸造SlushMolding凝塑成形HollowBlowMolding中空（吹出）成形SqueezeCasting高压铸造HotChamberDieCasting热室压铸Swaging挤锻HotForging 热锻TransferMolding转送成形InjectionMolding射出成形WarmForging温锻InvestmentCasting精密铸造MatchedDieMethod对模成形法LaminatingMethod被覆淋膜成形LowPressureCasting低压铸造LostWaxCasting脱蜡铸造MatchedMouldThermalForming对模热成形模CloseMold合模Demould脱模脱模剂MouldUnloading开模ToolChangeRetoolingDieChanging换模MouldClamping锁模各式模具分类用语BismuthMold铋铸模LandedPlungerMold有肩柱塞式模具BurnishingDie挤光模LandedPositiveMold有肩全压式模具ButtonDie镶入式圆形凹模LoadingShoeMold料套式模具Center-GatedMold中心浇口式模具LooseDetailMold活零件模具ChillMold冷硬用铸模LooseMold活动式模具ColdHobbing冷挤压制模法LouveringDie百叶窗冲切模CompositeDies复合模具ManifoldDie分歧管模具CounterPunch反凸模ModularMold组合模具DoubleStackMold双层模具Multi-CavityMold多模穴模具ElectroformedMold电铸成形模Multi-GateMold复式浇口模具ExpanderDie扩径模OffsetColdBendingDie双折冷弯模具ExtrusionDie挤出模PalletizingDie叠层模FamilyMold反套制品模具PlasterMold石膏模BlankThroughDies漏件式落料模PorousMold通气性模具DuplicatedCavityPlate复板模PositiveMold全压式模具FantailDie扇尾形模具PressureDie压紧模FishtailDie鱼尾形模具ProfileDie轮廓模FlashMold溢料式模具ProgressiveDie顺序模GypsumMold石膏铸模PortableMold手提式模具Hot-RunnerMold热流道模具PrototypeMold雏形试验模具原型模具IngotMold钢锭模PunchingDie落料模LancingDie切口模切缝模Raising（Embossing）压花起伏成形Re-entrantMold倒角式模具SectionalDie拼合模RunlessInjectionMold无流道冷料模具SectionalDie对合模具SegmentMold组合模Semi-PositiveMold半全压式模具Shaper 定型模套SingleCavityMold单腔模具SolidForgingDie整体锻模SplitForgingDie拼合锻模SplitMold双并式模具SpruelessMold无注道残料模具SqueezingDie挤压模StretchFormDie拉伸成形模SweepingMold 平刮铸模SwingDie振动模具ThreePlatesMold三片式模具TrimmingDie切边模UnitMold单元式模具UniversalMold 通用模具UnscrewingMold退扣式模具YokeTypeDie轭型模t-Plate弹簧箱顶板BushingBlockLinerBushing衬套CoverPlate盖板GuidePad导料块模具厂常用之标准零配件AirVentValve通气阀AnchorPin锚梢AngularPin角梢Baffle调节阻板AngularPin倾斜梢BafflePlate折流档板BallButton球塞套BallPlunger定位球塞BallSlider球塞滑块BinderPlate压板BlankHolder防皱压板BlankingDie落料冲头Bolster上下模板Bottomboard浇注底板Bolster垫板BottomPlate下固定板Bracket托架BumperBlock 缓冲块Buster堵口CastingLadle浇注包Castinglug铸耳Cavity模穴（模仁）CavityRetainerPlate模穴托板CenterPin中心梢ClampingBlock 锁定块CoilSpring螺旋弹簧ColdPunchedNut冷冲螺母CoolingSpiral螺旋冷却栓Core心型CorePin心型梢Cotter开口梢Cross十字接头CushionPin缓冲梢DiaphragmGate盘形浇口DieApproach模头料道DieBed型底DieBlock块形模体DieBody铸模座DieBush合模衬套DieButton冲模母模DieClamper夹模器DieFastener模具固定用零DieHolder母模固定板DieLip模唇DiePlate冲模板DieSet冲压模座DirectGate直接浇口DogChuck爪牙夹头Dowel定位梢DowelHole导套孔DowelPin合模梢Dozzle辅助浇口DowelPin定位梢Draft拔模锥度DrawBead张力调整杆DriveBearing传动轴承EjectionPad顶出衬垫Ejector脱模器EjectorGuidePin顶出导梢EjectorLeaderBush顶出导梢衬套EjectorPad顶出垫EjectorPin 顶出梢EjectorPlate顶出板EjectorRod顶出杆EjectorSleeve顶出衬套EjectorValve顶出阀EyeBolt环首螺栓FillingCore填充型芯椿入蕊FilmGate薄膜形浇口FingerPin指形梢FinishMachinedPlate 角形模板FinishMachinedRoundPlate圆形模板FixedBolsterPlate固定侧模板FlangedPin带凸缘针FlashGate毛边形浇口Flask上箱FloatingPunch浮动冲头Gate浇口GateLand浇口面Gib凹形拉紧楔GooseNeck鹅颈管GuideBushing引导衬套GuidePin导梢GuidePost 引导柱GuidePlate导板GuideRail导轨HeadPunch顶头冲孔HeadlessPunch直柄冲头HeavilyT aperedSolid整体模蕊盒HoseNippler管接头ImpactDamper缓冲器InjectionRam压射柱InlayBush嵌入衬套InnerPlunger内柱塞InnerPunch内冲头Insert 嵌件InsertPin嵌件梢KingPin转向梢KingPinBush主梢衬套KnockoutBar脱模杵Land 合模平坦面LandArea合模面LeaderBush导梢衬套LiftingPin起模顶针起模杆Lining内衬LocatingCenterPunch定位中心冲头LocatingPilotPin定位导梢LocatingRing定位环LockBlock压块LockingBlock定位块LockingPlate定位板LooseBush活动衬套MakingDie打印冲子ManifoldBlock歧管档块MasterPlate靠模样板MatchPlate分型板MoldBase塑胶模座MoldClamp铸模紧固夹MoldPlaten模用板MovingBolster换模保持装置MovingBolsterPlate可动侧模板OnePieceCasting整体铸件ParallelBlock平行垫块PartingLine 分模线PartingLockSet合模定位器PassGuide穴型导板PeenedHeadPunch镶入式冲头锤击强化冲头钻杆凸模PilotPin定位销导向销子PinGate针尖浇口Plate衬板PreExtrusionPunch顶挤冲头Punch冲头Puncher推杆PusherPin衬套梢Rack机架RappingRod起模杆Re-entrantMold凹入模RetainerPin嵌件梢RetainerPlate托料板ReturnPin回位梢RidingStripper浮动脱模器RingGate环型浇口Roller滚筒Runner流道RunnerEjectorSet流道顶出器RunnerLockPin流道拉梢ScrewPlug头塞SetScrew固定螺丝Shedder脱模装置Shim分隔片Shoe模座之上下模板Shoot流道ShoulderBolt肩部螺丝Skeleton骨架SlagRiser冒渣口Slide（SlideCore）滑块SlipJoint滑配接头SpacerBlock间隔块SpacerRing间隔环Spider模蕊支架Spindle主轴Sprue注道SprueBushing注道衬套SprueBushingGuide注道导套SprueLockBushing注道定位衬套SpruePuller注道拉料浇道推出杆注道残料顶销SpewLine合模线SquareKey方键SquareNut方螺帽SquareThread方螺纹LimitStopCollar限位套StopPin止动梢StopRing止动环Stopper定位停止梢StraightPin圆柱销StripperBolt脱料螺栓StripperBushing脱模衬套StripperPlate剥料板StrokeEndBlock行程止梢SubmarineGate潜入式浇口SupportPillar支撑支柱顶出支柱SupportPin支撑梢SupportingPlate托板SweepT emplate造模刮板TabGate辅助浇口TaperKey推拔键TaperPin拔锥梢锥形梢TeemingPouring浇注ThreeStartScrew 三条螺纹ThrustPin推力销TieBar拉杵TunnelGate隧道形浇口Vent通气孔WortlePlate拉丝模板模具常用之工作机械3DCoordinateMeasurement三次元量床BoringMachine搪孔机CNCMillingMachineCNC铣床ContouringMachine轮廓锯床CopyGrindingMachine仿形磨床CopyLathe仿形车床CopyMillingMachine仿形铣床CopyShapingMachine仿形刨床CylindricalGrindingMachine外圆磨床DieSpottingMachine合模机DrillingMachine钻孔机EngravingMachine雕刻机EngravingE.D.M 雕模放置加工机FormGrindingMachine成形磨床GraphiteMachine 石墨加工机HorizontalBoringMachine卧式搪孔机HorizontalMachineCenter卧式加工制造中心InternalCylindricalMachine内圆磨床JigBoringMachine冶具搪孔机JigGrindingMachine冶具磨床LapMachine研磨机MachineCenter加工制造中心MultiModelMiller靠磨铣床NCDrillingMachineNC钻床NCGrindingMachineNC磨床NCLatheNC车床NCProgrammingSystemNC程式制作系统Planer 龙门刨床ProfileGrindingMachine投影磨床ProjectionGrinder投影磨床RadialDrillingMachine旋臂钻床Shaper牛头刨床SurfaceGrinder平面磨床TryMachine试模机TurretLathe转塔车床UniversalToolGrindingMachine万能工具磨床VerticalMachineCenter立式加工制造中心WireE.D.M线割放电加工机入水Gate进入位GateLocation水口形式GateType大水口EdgeGate细水口Pin-pointGate水口大小GateSize转水口SwitchingRunnerGate唧嘴口径SprueDiameter流道MoldRunner热流道HotRunnerHotManifold温度控制器温控器ThermostatThermoregulatorsT emperatureController 热嘴冷流道HotSprueColdRunner 唧嘴直流DirectSprueGate圆形流道RoundFullHalfRunner流道电脑分析MoldFlowAnalysis流道平衡RunnerBalance热嘴HotSprue热流道板HotManifold发热管CartridgeHeater探针Thermocouples插头ConnectorPlug插座ConnectorSocket密封封料Seal运水WaterLine喉塞LinePlugThroatT aps喉管Tube塑胶管PlasticTube快速接头JiffyQuickConnectorQuickDisconnectCoupling 模具零件MoldComponents三板模3-PlateMold二板模2-PlateMold边钉导边LeaderPinGuidePin边司导套BushingGuideBushing中托司ShoulderGuideBushing中托边GuidePin顶针板EjectorRetainnerPlate托板SupportPlate螺丝Screw管钉DowelPin开模槽PlyBarScot内模管位CoreCavityinter-Lock顶针EjectorPin司筒EjectorSleeve司筒针EjectorPin推板EjectPlatePushPlateStripperPlate缩呵MovableCoreReturnCorePuller 扣机（尼龙拉勾）NylonLatchLock 斜顶Lifter模胚（架）MoldBase上内模CavityInsert下内模CoreInsert行位（滑块）Slide镶件Insert压座Wedge耐磨板油板WedgeWearPlate压条Plate撑头SupportPillar唧嘴SprueBushing挡板StopPlate定位圈LocatingRing锁扣Latch扣机PartingLockSet推杆PushBar栓打螺丝S.H.S.B顶板EjectorPlate活动臂LeverArm分流锥SprueSpreader分流板SpreaderPlate水口司Bush垃圾钉StopPin隔片Buffle弹弓柱SpringRod弹弓DieSpring中托司EjectorGuideBush中托边EjectorGuidePin镶针Pin销子DowelPin波子弹弓Ballcatch喉塞PipePlug锁模块LockPlate斜顶AnglefromPin斜顶杆AngleEjectorRod尼龙拉勾PartingLocks活动臂LeverArm复位键提前回杆EarlyReturnBar气阀Valves斜导边AnglePin术语Terms承压平面平衡PartingSurfaceSupportBalance模排气PartingLineVenting回针碰料位ReturnPinandCavityInterference 顶针碰运水WaterLineInterfereswithEjectorPin 料位出上下模PartfromCavith （Core）Side不准用镶件DoNotUse（CoreCavity）Insert 用铍铜做镶件UseBerylliumCopperInsert初步模图设计PreliminaryMoldDesign正式模图设计FinalMoldDesign弹弓压缩量SpringCompressedlength稳定性好GoodStabilityStable强度不够InsufficientRigidity均匀冷却EvenCooling扣模Sticking热膨胀ThermalExpansion公差Tolerance铜公（电极）CopperElectrode AirVentValve通气阀AnchorPin锚梢AngularPin角梢Baffle调节阻板AngularPin倾斜梢BafflePlate折流挡板BallButton球塞套BallPlunger定位球塞BallSlider球塞滑块BinderPlate压板BlankHolder防皱压板BlankingDie落料冲头Bolster上下模板BottomBoard浇注底板Bolster垫板BottomPlate 下固定板Bracket托架BumperBlock缓冲块Buster堵口CastingLadle浇注包CastingLug铸耳Cavity模腔模穴（模仁）CavityRetainerPlate模穴托板CenterPin中心梢ClampingBlock锁定块CoilSpring螺旋弹簧ColdPunchedNut冷冲螺母CoolingSpiral螺旋冷却栓。
注塑常用术语英文表达
1.雾气Moisture Streaks2。
玻纤分配不均Glass Fiber Streaks3.困气Gas Trap Effect4。
银丝纹Sliver Marks5.结合线Weld Line6.水波痕Water Wave Effect7。
黑点Dark Sport8。
顶出印Visible Ejector Marks9。
变形Deformation During Demolding10.填充不足Short Filling11。
冷料流痕Cold Slug12。
进胶口点不良Dull Spots Near The Sprue13。
喷射痕Jetting14.表面起层Flaking Of The Surface Layer15.浮泡Entrapped Air16。
过热变色Burnt Streaks17。
龟裂Stress Crack18。
缩水痕Sink Marks19。
真空气泡Density Bubble20。
披锋Flash21。
擦伤印Scratch MarksGlass fiber rich surface/glass emergence on the surface 22 尺寸过大Over dimension23尺寸过小Under dimension24 翘曲Warpage/warped25 收缩Shrinkage/shrink26 缩影Sink marks27 打不满Short shot/short molding塑料模具mould of plastics注塑模具injection mould冲压模具die模架mould base定模座板Top clamping plateTop plateFixed clamp plate水口推板stripper plateA板A plateB板B plate支承板support plate方铁spacer plate底针板ejector plate面针板ejector retainer plate回针Return pin导柱Guide pin有托导套Shoulder Guide bush直导套Straight Guide bush动模座板Bottom clamp plate Moving clamp plate基准线datum line基准面datum plan型芯固定板core-retainer plate凸模固定板punch—retainer plate顶针ejector pin单腔模具single cavity mould多腔模具multi—cavity mould多浇口multi—gating浇口gate缺料starving排气breathing光泽gloss合模力mould clamping force锁模力mould locking force挤出extrusion开裂crack循环时间cycle time老化aging螺杆screw麻点pit嵌件insert活动镶件movable insert起垩chalking浇注系统feed system主流道sprue分流道runner浇口gate直浇口direct gate ，sprue gate轮辐浇口spoke gate ，spider gate 点浇口pin-point gate测浇口edge gate潜伏浇口submarine gate , tunnel gate 料穴cold—slug well浇口套sprue bush流道板runner plate排飞槽vent分型线（面）parting line定模stationary mould，Fixed mould 动模movable mould，movable half 上模upper mould, upper half下模lower mould，lower half型腔cavity凹模cavity plate，cavity block拼块split定位销dowel定位销孔dowel hole型芯core斜销angle pin，finger cam滑块slide滑块导板slide guide strip楔紧块heel block, wedge lock拉料杆sprue puller定位环locating ring冷却通cooling channel脱模斜度draft滑动型芯slide core螺纹型芯threaded core热流道模具hot-runner mould绝热流道模insulated runner mould熔合纹weld line （flow line）三板式模具three plate mould脱模ejection换模腔模具interchangeable cavity mould脱模剂release agent注射能力shot capacity注射速率injection rate注射压力injection pressure差色剂colorant保压时间holdup time闭模时间closing time定型装置sizing system阴模female mould，cavity block阳模male mould电加工设备Electron Discharge Machining数控加工中心CNC machine center万能铁床Universal milling machine卧式刨床Horizontal planer车床Engine lathe平面磨床Surface grinding machine去磁机Demagnetization machine万能摇臂钻床Universal radial movable driller 立式钻床Vertical driller超声波清洗机Ultrasonic clearing machine。
注塑专业名词
注塑专业名词中英文对照表英语名称中文名称Hopper Dryer 料斗干燥器Injection Molding Cycle 注塑周期Crushing Mill 粉碎机Precision Injection 精密成形Gas Injection/AGI 吹气成形、气辅成形Set the condition 设定注塑前提Machine 机械Mold Set-Up 上模Screw 螺杆、螺钉、螺旋Mold Down 下模Screw Head 螺杆头Pressure 压力Joint 接头，接缝Low Pressure 低压Injection 注塑Low Pressure Clamping 低压锁模Feeder 送料（加料）器Holding Time 保压时间Compound 混炼料Back Pressure 背压Blend 搅浑，调和Clamping Force 合模力Mixer 混淆器Hold Clamping Pressure 锁模型压成力Mixing 混淆Clamping Stroke 合摸行程Cooling 冷却Clamping Unit 锁模装配Cooling Tower 冷却塔Mold Opening 开模Chiller 冷水机Mold Closing 合摸Temperature Controller 温调机Speed 速率Cylinder 料筒Injection Speed 射出速率Heater 加热器Injection Capacity 注塑量Band Heater 加热圈Charging 计量Thermocouple 热电偶Charging Stroke 计量行程Nozzle 射嘴Rib 骨位，筋位，增强筋Nozzle Head 射嘴头子Insert 嵌件，镶嵌"Tie Bar,Tie Rod" 拉杆，拉杠Wall Thickness 胶厚，壁厚Distance Between Tie Rods 拉杆距离Plasticizing 塑化Limit Switch 限位（限定）开关Thermal Decomposition 热分化Operation Switch 操作开关Shrinkage 收缩Operation Guide 操作指南Resin 树胶Control Panel 节制器Material 原料，质料Automatic 全自己主动Plastics 份子化合物塑料，塑胶成品Semi Auto 半自己主动Rubber 橡胶Hand 手动Master Batch 色母Handle 手柄Powder 色粉，粉，粉末Extruder 押出机，挤塑机Dry Color 色粉，干色料Extrusion Molding 挤塑Pellet 粒，塑胶粒Blow Molding Machine 吹塑机"Glass Fiber,Fibrous Glass" 玻璃纤维Blow Molding 吹塑Hose 软管，管Program Control 步伐节制Over Packing 过充填Process 工艺，工序，历程Mold Mark 马克模伤，模痕Inject visor 注塑工艺步伐节制装配Shock 冲击Damage 损坏，毁伤Cold Slug 冷料Sink 马克抽水，紧缩Cold Slug Well 冷料井Short Shot 充填不足，欠料Freeze 冷凝Flash 毛刺，披峰Hydraulic 液压，油压String Flash 胶丝Ghydraulic Ejector 液压顶出，液压脱模White 马克白化，顶白Hydraulic Pump 液压泵Silver 雪白，银痕Hydrautic 摩托液压电动机Flow mark 流纹air compressor 空气压缩机，空压机burn 烧黑，烧焦oil leakage 漏油异物black spot 异物，黑点oil tank 油箱，油槽sticking 粘模piston 活塞weld 溶接线，联合线air cylinder 气缸flash 料花alarm 报警oil 马克油污，油渍safety gate 太平门damage 打痕，击伤emergency stop 紧迫遏制cracking 裂，开裂color change 换色jetting 气纹purge material 清机份子化合物塑料deform 变型resin thermal 胶料温度warping 屈曲，翘曲，外倾mold thermal 模温bend 屈曲，翘曲，外倾heat up 升温，升热torsion 扭曲air shot 空射蛟，空打uneven color 色彩不均匀try 试模Eccentric Wall thickness 壁厚不匀称mold release 脱模"bladder,cell" 气泡儿，浮泛，空地mold release agent 脱模剂stripes 条纹rust preventatives 防锈剂dirty 污痕，污点，渗溢can't release （产物）没有办法脱模flaking 脱落，剥落shot 注，射tear off 上下翻动gate 进点，浇口float 浮起center gate 中间浇口screw damage 螺钉滑牙sprue runner 水口，注口，流道料shortage 员数不足，欠品clearance 距离，余隔run out 跃动度，偏疼sprue 主流道注（塑）口contraction 紧缩runner 流道，流道料assembly NG 嵌合不良，装配不良air vent 散气眼，透风口stress 应力breathing 排气，散气internal stress 内部策应力anneal 热措置惩罚，退火preparation 摆设，筹办mold 生产模型stopper 挡块machining center 加工中间stripper 推板，脱模型板universal milling machine 刨床，锣床spacer plate 垫板latter 车床mould base 模胚surface grinder 最简单的面磨制机床support plate 托板grinding drilling 钻床support pillar 撑头electric discharge machine 火花机加工puller lock 拉塞wire EDM 线割切puller bolt 拉杆nitride steel 氮化钢取付板top clamp plate 工字板，水口板nitrogen 氮气bottom plate 底板nitride 氮化措置惩罚return 回针titanium 钛guider pin 导柱heat treatment 热措置惩罚guider bush 导套hardening 淬火die 生产模型，动模，移动模型板Temper 回火die plate 模型板，载模型板annealing 退火module 板块，模件，模数pre harden 预加硬钢parts 零件，生产模型零件hardness 硬度eye bolt 吊环螺栓soft 软，软的crane 吊车，行车electrodes 铜公hook 勾，吊勾insert 镶件wire 钢丝，钢丝绳slide 行位，滑块file 锉子taper 斜度oil stone 油石taper 斜度，锥度，锥形的sand paper 砂纸draft 脱模斜度mesh 节号，目guide pin 导向柱刻印engrave 刻印sleeve pin 司筒针texture 蚀纹square pin 扁顶针放电目EDM texture 火斑纹angular ejector 斜顶针rough 粗的cavity 模腔，前模，母模trifling 细的，幼的core 模心，后模，公模diamond cut 钻石纹number of cavities 取数，模腔数roulette 滚花刀，刻痕rocket ring 定位环blast 喷沙o ring O环，胶圈hot runner 暖流道wall trickness 肉厚，胶厚repair 补缀add material 加胶接welding 溶接，焊接building 加胶溶接机welder 焊机，电焊机cut material 减胶溶接棒welding rod 焊条，电焊条modify the tooling 改模（因设变补缀）argon arc welder 氩弧焊repairing the tooling 生产模型补缀torch bumper 喷燃烧现象器，火苗燃烧现象器design 预设ejector pin 顶出design drawing 预设图ejector pin 顶针design change 预设变动，设变gate type 水口体式格局designer 预设者，预设职员tunnel gate 隧道式浇口，潜入水下口designer 预设者pin point gate 针孔形浇口，细水口mold design 生产模型预设side gate 侧水口，洪流口mold specification 生产模型建造仕样书direct gate 直接浇口specification 规格multi gate 复式浇口mold construction 生产模型机关，生产模型布局fan gate 扇形浇口input 输入film gate 扇形浇口programming 编程jump gate 搭接浇口3D drawing 3D图，3维图gate balance 浇口均衡2D drawing 2D图，最简单的面图undercut 凹槽，倒扣front elevation 正面图cooling line 水管，运水plan 平面图cross-sectional drawing 剖面图cooling 冷却回路，运水CAD date CAD数值modeling 模mock-up 模子，原尺寸模子software 软体hand made sample 手板，手工样品mold drawing 生产模型图module 模数，模量，模件part drawing 零件图gear 齿轮，传动装配diagrammatic sketch 草图helical gear 螺旋齿轮drawing 绘图solid 群体的，固体revised drawing 图订变换transformation 变换，转换dimensioning 记入尺寸floppy disk 磁盘，软盘out mold direction 出模标的目的computer 台式机，计较机draft 出模斜度personal computer 私家用电器脑，手提台式机pitch 间距，齿距version 情势，品类（译文，翻译，译本）angle 角度reading 读取projected area 投影平面或者物体表面的大readout 读出taper 锥度，斜度reading 度数under cut 倒扣压缩compression 压缩2 plate 两板模开open 打开，读出文件（软体）3 plate 三板模not open 打（解）不开，读不出offset 偏置，偏移miss 纰缪，掉误mold layout 分模condition of the progress 进程项度状态split mold 对于开式生产模型finishing 打光，磨光slide core 滑动模芯polish 研磨，打磨loose core 勾当模芯target 方针，目的，对于准loose mold 勾当生产模型schedule 每一日安排表press 冲压，压床，压maintenance 维护，调养press machine 冲床did casting 压铸progressive 级进sintering 加热使黏结single 单冲monkey 勾当板子packing plate 垫板clamp 夹具（固定生产模型用）punch 冲头，凸模，冲床scrap 废铁，废物，废渣punch press 冲孔机rust 生锈die 下模rust inhibitor 防锈剂die set 模座，模架washing agent 洗濯剂press mold 冲压模，五金模ultrasonic cleaning 超音波洗濯leveler 整平滚，矫平机feeder 送料机，加料机burr 反边，毛刺drawing 拉伸thinner 天纳水，淡薄剂burring 去毛刺triclinic 三氯乙烯脱脂剂blank 复合trivalent chromium 六价铬cutting 落料，冲孔bending 折弯degreasing 脱脂，去油bend 折弯，屈曲harmful metal 有害物box-bending 箱cut 割切L-bending L折弯"press, sheet metal" 板金V-beding V折弯cut 堵截，割断punching 冲孔，钻孔iron plate 铁板SECC 镀锌板cutting 冲压，抽去silver top 镀锌板shirk 避空stainless 不锈钢calking 铆接copper 铜tap 螺丝攻brass 黄铜dies 板牙steel 钢reamer 铰孔aluminum 铝reamer 铰刀，扩孔器width 宽度end mill 刨刀thickness 板厚grinder 砂轮机，磨制机床density 疏密程度barrel 滚筒coil 卷材barrel tumbling 滚（捅抛）光width cut 片材plating 电镀nut 螺丝帽，螺帽electro plating vacuum 真空电镀bolt 螺栓，螺杆spot welding 点溶接，点焊chrome plating 镀铬jip 夹具，治具galvanization 镀锌clearance 间隙shave 切，削matching 接口assembly 装配，组装counter 统计器assembly unit 装配组件count method 统计法assembly time 装配工数timer 按时器line 生产线，拉线digital 数码（的），数码self 单人装配digital camera 数码拍照机conveyer 传送带connect 插座，插嘴U line U形出产线plug 插头，瓶塞capacitor 电器皿lamp 灯resistor 电阻器lighting 点灯，灯亮diode 二极管fuse 断电丝LED （light-emitting diode) 闪光二极管power code 电源线transistor 形成品体体管wire hamess 电线导线IC 集成电路bar code 条纹码lcd(liquid crystal display) 液态品体预示器vinyl tape 绝缘带sensor 传感器noise 异音，杂音，噪音relay 替续器decibel 分贝（声强单位）connector 保持器instruction sheet 功课引导书transformer 变压器access platform 功课台breaker 断路器series 串联buzzer 蜂鸣器parallel 并联printed circuit board/PCB 印刷电路板clutch 联轴器，聚散器driver 螺钉刀，起子solenoid coil 电磁线圈driver 十字批（起）coil 线圈driver 一字批（起）static electricity 静电electric drive 电动螺钉刀，电批prevent electricity 防静电torque 扭矩，转矩fan motor 电扇电动机screw 螺钉刀，起子grease 润滑washer 垫圈（片）apply 涂油e-ring 卡环block copy 底板，草图solder 焊锡film 胶卷，软片soldering iron 烙铁silk print 丝印tin 锡pat print 移印earth 接地，地线hot sample 烫印alcohol 火酒，乙醇ink 印字油墨foot switch 脚踏开关color sample 色板terminal 端子print NG 印刷不良terminal block 端子板bleeding 渗溢，飞油label 标贴，标签stamp 捺印bar code 条纹码，条形码spray 涂装，喷涂mile 软片，聚酯树胶wood graining 木纹加工quality control 品位办理sample 样品，样本，样板inspection 查抄boundary sample 限度样板IQC 验收，受入查抄approval sample 认可样板OQC 出货查抄tolerance 公役PQC 工程查抄plus 正，加号sampling 抽查minus 负，减号total inspection 全检disperse 不变，颠簸visual inspection 目视查抄unstable 不稳固appearance check 外不雅查抄balance 均衡patrol 巡检process capability /CP 工程能力measurement 丈量仪三角螺丝刀detection 检验测定measurement 张良，标定check point 查验（重）点measuring method 丈量要领no check 漏检clogging 刻度，分度special adoption application 特采审请memory 储存，影像provisional countermeasure 暂定对策three-dimensional measuring machine 3D丈量仪permanent countermeasure 长久对策microscope 东西目镜claim 投诉，抱怨，索赔profile projectior 投影机appraisal 评价slide calipers 卡尺decide 鉴定micrometer 量具，检查基准check standard 查抄基准lever type dial test 百分表检查基准表inspection sheet 查抄基准表torque gauge 扭转力计QC 工程表QC flow chart QC工程表scale 刻度尺specula face 镜面square 90度角尺mirror face 光面，光泽面steel tate 皮尺texture face 蚀纹面height gauge 高度尺first the face 一级面pin gauge 柱规appearance 外不雅面thickness gauge 片appearance part 外不雅产物protractor 角度仪function part 性能部品tension gauge 拉力机slide 滑动面indicator 百分表检查基准表flatness 最简单的面度hardness tester 硬度计reform 矫正multitester 万用表check jig 查抄用治具surface plate 平台，平板feed back 反馈V block V形块communication 信息，抱怨gauge block 方块规manual 指南，手册dial gauge 百分表flow chart 流程图data 数值process inspection 工程监查data sheet 数值单qualification 确定地认为parameter 参量graph 图表，曲线图warehouse 堆customhouse 海关pallet 卡板customs clearance 报关，通关corrugated fiberboard 纸箱customs clearance 报关手续partition 刀卡electronic data interchange 电子报关recycle box 周转箱container 货柜车plastics box 折叠式周转箱foot 英尺container 份子化合物塑料周转箱packing list 装箱单poly-bag 胶袋list 详细登记单tape 封箱品牌一字螺丝刀胶纸declaration 申请报告rope 绳索，线import 入口first in first out 先入先出export 出口fork lift 铲车fumigation certificate 熏蒸证实书hand lift 手推铲车no wood packing certificate 无木质包装证实书bogie 台车wooden box 木箱truck 卡车shelf 货架license 批文，容许stock 在库数license document 转厂shelf 盘货limits 指标，配额指标dead stock 死仓储，积压品import limits 入口指标purchasing 采集购买unbalance 数目不服衡supply parts 支给品contract 合约purchase parts 采集购买品contract 手册lead time 交货期，定货期order placement 发定单"transfer,carry over" 转余料，拨余料pay 有偿erase 核销free of charge 没有报酬的provision of information 加签vender 供应商submit document 递单quotation 报价单brand name 商物品名称invoice 发票，请款单goods No 商品编码deposit 预付款，包管金foreign enterprise 外资企业payment 付款owned enterprise 独资企业payment condition 付款partnership enterprise 合资工厂month payment 月结processing 来料加工over time 加班（没事了事情日加班）bailment processing 委托加工over time fee 加班费labor cost 人件费holiday work 加班（节假日上班）amortization 折旧费two shift 两班制hour charge 加工费，工时费day shift 白班exchange rate 汇价night shift 晚班material certificate 质料证实书。
注塑方面英语术语
注塑方面英语术语注塑方面英语术语标签/分类：压铸 die-cast压炼 injection铸件 casting/cast/founding起泡/气泡 bubble/blister/airbubble缺料 shor-shots/undershot浇不足/*铸 under-founding多料 superfluities/superfluous material(alloy)顶针痕 ejector(pins) mark花纹 flow mark/flow line冷纹 cold mark/cold streak油纹 oil streak走水纹 splash mark银纹 silver streaks霜纹 splay mark夹水纹 silver streaks/flow line/weld line扣模/粘模 spruesticking砂眼/气眼 air hole（塑胶件）弯曲/变形 warping/warpage变形 deformation扭曲 twist翅曲 warp/warped材料错误 usingwrong plastic material凸痕 convex mark凹位/凹陷 sink mark/dent mark披锋 flashing批损 pare-mark/cutmark批凹 pare off锉纹 trim-mark/file-mark锉损 excessivetrim mark黑点/黑纹 black spots/black streak发白 white mark烧焦 burnmarks刮花/刮痕 scratch mark擦痕/擦伤 rub-mark/brush-burn裂缝 cracking裂纹 crakingline碰损 stress mark起皮 chip错位（合模线） part linemisaling ment孔位尺寸改变 dimensionvarious哑色 dull color表面变光滑（喷油面） glossy finishing表面 sruface/outside镶件 insert/insert word缩水/收缩 sinkmark/shrinkage/shrink mark 偏差 colordeviation色粉 colourment颜色 colour/color零件污糟 dirty mark on part顶白 stressmark/ejector mark屈曲 bent夹模线移位 part line misalignment胶件料厚不均 uneven wall thickness水口料 degradedmaterial凹印 sink mark擦花 abrasionmark混色 contamination mark热点不良 poor heat sticking模具方面：定位圈 locating ring唧嘴 spruebush (浇口套)A板 Aplate (定模板)B板 Bplate（动模板）方铁 spacer block (垫铁)底板 bottom clamp plate(动模底板)面板 top clamp plate(定模底板)顶针 ejector pin（顶杆）直边钉 guide pin (导柱)托司 shoulder guide bush(导套)直司 straight guide bush(导柱)回针 returnpin(回程杆)细水口边钉 support pin(副导柱)蓝弹簧 blue spring（回程弹簧）水口推板 runner stripper plate(卸流道板)中边钉 ejector guide pin (顶板导柱)顶针板 ejector retainer plate(顶杆固定板)顶针底板 ejectorplate(顶杆垫板)撑头 support pollar（支撑柱）垃圾钉 stop pin (限位钉)呵 core (后模肉内镶件)后模肉 back mold body(后模镶件)前模肉 cavity（前模镶件）扣鸡 P-lock。
模具注塑术语中英文对照
模具注塑术语中英文对照模具注塑是一种重要的加工工艺，它广泛应用于各个行业，例如汽车、电子、医疗等。
为了便于更好地理解这个工艺，我们需要明确其中的术语。
以下是一份模具注塑术语的中英文对照表。
1. 模具(mold) - mold是模具注塑过程中必需的工具，它通常由钢铁或铝制成，包含两个或更多空腔，以使熔融的塑料材料流经并注入成型的形状。
2. 注塑(molding) - molding是一种塑料成型加工工艺，其中熔融的塑料材料通过模具的设计形状，被注入到一个凹模和模具上部的凸模之间，并在冷却后形成一个具有特定形状和尺寸的零件。
3. 射出成型(molding by injection) - injection molding是一种将针对特定形状和尺寸的塑料材料注入到模具中而不是将固体材料切割和熔化的塑料成型技术。
4. 压铸(molding by compression) - compression molding是一种用于高温、高压和强力形式的适用于大批量塑料成型的方法，材料被放置在预计大小的模具空间中，并在关闭模具后施加高压力，使其融合。
5. 凹模(cavity) - cavity是模具上一侧的镂空，通常是制成零部件的形状。
6. 凸模(core) - core是模具上另一侧的立体形状，用于创建凹模的形状。
7. 浇口(gate) - gate是塑料注塑过程中，针对特定形状和尺寸的模具，将熔化的塑料材料注入到模具空腔中的位置。
8. 引流道(runner) - runner是与模具中凹、凸模相连的通道，其功能是向模具空腔中的塑料材料提供流动。
9. 母材(stock material) - stock material是进入注塑模具成型的未加工的固体或液态塑料原料。
10. 热流道(hot runner) - hot runner是一种温度可控的通道，用于将塑料材料从液态状态注入到模具制成的凹模空腔中。
11. 总成(assembly) - assembly是由多个部件组合而成的成品，通常用于汽车和电子行业中。
注塑行业术语中英文对照
扁顶杆
flat ejector pin
工作截面为矩形的顶杆
连接推杆
ejector tie rod
连接推件板与推杆固定板，传递推力的杆件
导套
guide bush
与导柱相配合，用于初步确定模具
导柱
guide pillar
起导向作用的部件，一般为圆柱体
浇口
gate
连接分流道合型腔的进料通道
位移
Displacement
熔体内部压力差引起高压部份向低压部分推移现象可产生层次感
分层表面剥离
delamination
同一树脂或不同树脂发生层流后产生的 现象
三角洲效应
delta effect
局部温度差
方向收缩
diectional shrinkage
由大分子链排列引起的具有方向特性的收缩
尺寸变化
dimensional variation
控制面板
contorl plat
对设备参数控制的简易操作平台
显示器
pro-face
显示设备必要信息的屏幕
安全门
saft door
防止事故发生增大安全系数的保护装置门
注射座
enjection blend
注射成型机组成部件支撑并协助注射的金属平台
螺杆
screw
起旋转计量作用的螺纹状部件.是成型机的核心机械件
锁模系统
clamping system
模板控制系统注塑机上系统的一部分
控制系统
control system
计算机通过检测、处理信息并重新输入计算机进行控制相关参数
抽芯距
core-pulling distance
注塑、模具行业术语：英汉对照版！
注塑、模具行业术语：英汉对照版！（一）模具专业基本用词 Professional Terms1．塑料— plastic, resin2．样件— sample3．钢料— steel4．注塑机— injection machine, press5．产品— part, product, moulding6．模具— mold, mould, toolA 简易模（样板模）— prototype moldB 量产用模具— production mold7．三维造型（数模）—3D model, 3D data8．二维产品图— 2D part drawing9．设计— design10．制造— manufacture, build up, construction, fabrication, make11．检验— check, inspection12．测量— measure, inspection13．修改— change, modify, correction14．工程更改— engineer change15．质量— quality16．数量— quantity17．基准— datum, reference（二）如何解析2D 产品图？How to read 2D part drawing?一．产品几何 Geometry1．点— point2．线（边）— line, edge3．面 faceA 侧面— sideB 表面— surfaceC 外观面— appearance surface4．壁厚— wall thickness, stock thickness5．加强筋（骨位）— rib6．孔— hole7．细长的槽— slot8．柱位— boss9．角— cornerA 圆角— filletB 倒角— chamferC 尖角— sharp corner10．斜度— angle, taper11. 凹槽—recess , groove二. 分模信息 Splitting1．分型线— parting line (P/L), splitting line2．主分模方向— main direction, line of draw3．浇口设定— gating一．产品标识 Part Identification1．产品名称— part name (P/N)2．产品编号+版本号— part number + revision (Rev.) 3．型腔号— cavity number4．材料标记— material symbol5．模具编号— mold number (no.)6．日期印— dating insert, date code7．循环印— cycling code8．公司标志— company logo二. 技术要求 Specification (Special Requirement)1．项目启动表 Kick-off sheet1）项目名称— program name, project name2）产品名称— part name, product name, part description 3）产品编号— part number (P/N)4）客户模号— customer mold no.5）项目启动日期— kick off date, start date6）项目完成日期— due date, lead time7）内模件用钢— tool steel8）型腔数量— number of cavities9）数据文件编号— data file no.10）注塑材料— resin, plastic, raw material11）收缩率— shrink, shrinkage, shrink factor12）注塑机吨位— molding machine size, injection machine size13）成型周期— cycle time14）型腔光洁度— cavity polish15）型芯光洁度— core polish16）皮纹（晒纹）— texture, grain17）拔模斜度— draft angle, removal taper18）注塑件颜色及光泽— molded color & gloss19）模具加工地— manufacturing facility20）热流道供应商—manifold manufacturer, manifold supplier21）浇口位置— gate location / position22）浇口类型— gate type产品标识— stamp information, part identification特殊要求— special instructions1．产品质量及外观要求 Part Quality & Appearance Requirement1）尺寸及公差 Dimension & Tolerance① 重要尺寸— critical dimension, important dim., key dim.② 理论尺寸— nominal dimension③ 实际尺寸— actual dimension④ 公差— tolerance⑤ 公差带— tolerance range⑥ 尺寸超差— dimension deviation⑦ 接受（合格）— accept, OK⑧ 拒绝（不合格）— reject, refuse, obsolete, NG⑨ 让步接受— concession, special admit⑩ 返工— re-work2）产品缺陷（常见的）Defects (normal)① 缩水— sink mark, shrinkage② 飞边，毛边— flash, burr③ 段差— mismatch discrepancy④ 银丝纹，蛇纹— snake marks, streak⑤ 弯曲，变形— warpage, distortion⑥ 打不饱（缺料）— short shot⑦ 熔接线— weld line⑧ 多胶— unwanted plastic⑨ 拉伤—damage2．产品外观 Part Appearance① 产品颜色— part color② 产品光泽— gloss③ 皮纹粒度— grain3．常用词汇、词组及短语 Normal Word, Short Sentence1）单边— per side2）双边— both sides3）加入，添加— add, incorporate4）去除，取消— remove, cancel5）满足…的要求，符合，与…要求一致—according to, conform to, satisfy, meet6）要求，需要— require, need, demand7）确认—be approved, agreed by …8）允许— permit, allow9）在…范围之内— within10）不可以，不允许，禁止— free from, prevent, avoid11）…，除非有另指—… unless otherwise specified12）…或少于—…or less13）自动化运作— automatic operation14）未注尺寸（详细形状）见三维造型Non dimensioned contour (detailed shape) see 3D model.15）分型线上的飞边（披缝）或段差应小于…Burrs or discrepancy on the P/L shall be … or less.标题栏 Title Block1．产品名称— part name2．图纸编号 + 版本号（索引号）—drawing no. + level (index)3．一般公差— general tolerance（三）如何阅读制模标准？How to read tooling standard?一．模具结构术语 Mold Construction TermsA．模架 Mold Base1．模架量化特征 Measurement Feature① 长 X 宽 X 高— Length X Width X Height② 模具高度尺寸（模厚）— stack height of mould③ 模具重量— total weight of mould, mould thickness2．定模底板— front plate, top clamping plate, clamp plate, clamping plate3．定模板— cavity plate, fixed mould plate, A – plate4．动模板— core plate, moving mould plate, B – plate5．支撑板— support plate, backing plate6．间隔板,方铁— support blocks, rails, risers, spacer block 7．顶杆固定板— retaining plate, ejector retaining plate8．顶板— ejector plate，bottom clamping plate9．动模底板— back plate10．导柱— guide pillar, leader pin, guide pin 11．导套— guide bush, leader pin bush12．复位杆— return pin, push-back pin13．弹簧— spring14．撑头— support pillar15．顶针板导柱、导套— ejection guide pin / bush 16．垃圾钉— stop pin, stop button17．模脚— standing-off pillars18．标牌— plaque scutcheonB．成型零部件 moulding components1．型芯— core insert2．型腔— cavity insert3．镶针— core pin4．镶块— sub-insert, split5．滑块— slide, sliding split6．斜顶— lifter, angled-lift split, loose coreA 斜顶头— lifter headB 斜顶杆— lifter rod, lifter shaft7．成型顶杆— moulding face pin, form pin C．浇注系统 Feed System1．塑料 Mouldinga．主流道— sprueb．分流道 runner① 主分流道— main runner② 二级分流道— branch runner分流道断面形状 cross-sectional shape of runner① 圆形— full round② 半圆形— semicircular③ 梯形— trapezoidalc．浇口 gate常用浇口形式 normal gate type :① 边缘浇口（J型浇口）— edge gate, J – gate② 侧浇口— side gate③ 潜伏式浇口— sub-gate, subsurface gate, submarine gate, cashew gate④ 潜伏式二次浇口(隧道式浇口) —tunnel gate onto feeder post⑤ 点浇口— pin gate⑥ 直接浇口(主流道型浇口) — sprue gate, direct gate⑦ 护耳式浇口— tab gated．模腔— impressione．冷料井— cold slug wellf．热流道— hot runner2．模具零件 mold componentsa．定位圈— locating ring, location ring, register ringb．浇口套— sprue bushc．挡圈— stop ringd．浇口镶块— gate inserte．热流道板— manifoldf．热嘴— hot drophot sprue分型面及其锁紧、排气 Parting Surface, inter-locking & venting1．分型线— parting line ( P/L )2．镶拼线— bodyline, joint line3．平 / 不平的分型面— flat / non – flat parting surface4．封胶面— shut off surfaces, seal-off surfaces5．擦穿位— shut off6．碰穿位— kiss-off7．管位— parting line lock8．分型面的释放(避空) — relief of parting surface9．分型面的平衡— balancing of parting surface10．锁紧角度— locking angle11．锁紧力— clamping force12．锁模块— safety strap13．精定位— Interlock, die lock14．困气— air trap15．排气槽— vent, vent slotE．滑块机构 Slide1．驱动 Actuation① 斜导柱— angle pin, horn pin, cam pin② 弹簧— spring③ 油缸— hydraulic cylinder2．制动 Detention① 滑块固定器— slide retainer② 弹簧制动器— spring-loaded detention (plunger)③ 挡钉、挡板— stop pin, stop plate, slide stop3．导轨— gib, guide strip4．锁紧块（楔紧块）— heel block, locking heel, wedge block, chase block5．耐磨片— wear plate, wear strip6．压板— retainer, gib7．螺钉— screw8．定位销— dowel pinF．斜顶机构 Lifter1．斜顶头— lifter head2．斜顶杆— lifter rod, lifter shaft3．开口销— split pin4．固定板（压板）— retainer plate5．耐磨片— wear plate6．铜导套— bronze bushing7．衬套— spacer8．导轨— L – gib9．滑动块— slideG．顶出系统 Ejection System1．基本词汇 Basic Word① 顶出行程— ejection stroke② 模具开档— daylight③ 粘模— stick④ 产品脱模—part is push off from, clear part of mould, separation of part2．顶板机构 Ejector plate assembly① 顶板— ejector plate② 顶板固定板— retaining plate③ 推板— stripper plate④ 推板导柱— ejector guide pin⑤ 推板导套— ejector guide bush⑥ 撑头— support pillar3．复位机构 Return System① 复位杆（回程杆）— return pin, push – back pin② 垃圾钉— stop pin, stop button③ 压簧— compressed spring④ 碟簧—a stack of ―Belleville‖ washers⑤ 早复位机构— early return system⑥ 强制复位机构— positive return system4．顶出方法 Ejection Techniques1）顶杆顶出— pin ejection2）顶管顶出— sleeve ejection3）顶块顶出— bar ejection4）扁顶顶出— blade ejection5）顶板顶出— stripper ejection6）油缸顶出— hydraulic ejection7）气顶— air ejection8）阀门顶出— valve ejection5．顶出元件 Ejection Elements1）拉料杆— sprue puller, sucker pin2）顶杆— ejector pin3）阶梯式顶杆— stepped ejector pin1）顶管— ejection sleeve, sleeve2）扁顶— ejector blade, slabbed off ejector pin3）顶块— stripper bar4）顶环— stripper ring5）推板— stripper plate6）加速顶— accelerated ejection1．顶出辅助机构 Supplementary operating system1）弹簧柱塞器— spring – loaded plunger2）弹珠定位器— ball catch system3）插销式锁扣— Latch – lock4）尼龙拉杆装置— friction puller device2．电器元件 Electric Components1）压力传感器— pressure transducer2）限位开关— limit switchF．冷却系统 Cooling System1．基本词汇 Basic Word1）温差— temperature variation2）水孔（水道）—waterlines, water-ways, flow-way, channel3）水路— cooling circuit4）水路示意图— water schematic, schematic circuit5）冷却液— coolant, coolant fluid6）内连接— interconnect7）外连接— external connection8）出口、入口— outlet、inlet9）漏水— water leakage2．水路分布 Circuits1）阶梯式水路— stepped system2）分隔板水路— baffled hole system3）斜孔式水路— angled hole system3．水路元件 Components1）闷头（螺塞、止水栓）—（threadless）brass pressure plug : female plug & male2）隔水片— baffle3）密封圈— O – ring4）快插水路接头—quick disconnect fitting, quick connection adaptor5）弯头— elbow6）偶合器（连接器、接头）— adaptor (including a plug & a socket)7）橡皮管— rubber hose1）分水板,集水块— water manifoldG．螺纹、螺纹孔 & 螺钉 Thread, thread hole & screw1．螺纹— thread2．管螺纹— pipe thread3．螺纹孔— screw hole, tapped hole4．起吊孔— handling hole, jack screw hole, eye bolt hole 5．螺钉— screw6．内六角螺钉— socket headed cap screw （s.h.c.s.）7．沉头螺钉— flat headed cap screw （f.h.c.s）8．螺栓— bolt9．螺母— nut10．锁紧螺母— locknut11．螺纹标准 Thread Standard① 公制标准— Metric② 英制标准— Imperial③ 英制管螺纹标准— British Standard Pipe thread （BSP）④ 美制管螺纹标准— NPT⑤ 美制粗螺纹标准— United Coarse thread （UNC）⑥ 美制细螺纹标准— United Fine thread （UNF）H．润滑 Lubrication1．润滑槽— grease groove2．加油管— grease line3．油杯— lubrication fittingI. 测量仪器 Measuring Instruments1．游标卡尺— vernier caliper2．千分尺— micrometer3．高度规— height gauge4．刻度规— dial gauge5．三坐标测量仪（三次元）— Coordinate Measure Machine （CMM）6．塞规— pin gauge7．圆角量规— radii gauge8．轮廓投影机—profile projectorJ．注塑机参数 Injection Machine Parameter1．注塑机规格参数 Injection Machine Specification① 锁紧类型 clamp typea．油缸— hydraulicb．肘杆式— toggle② 垂直注塑机导柱间距— tie bar vertical clearance③ 水平注塑机导柱间距— tie bar horizontal clearance④ 台板尺寸— platen dim.⑤ 最小 / 最大模厚— mold height Min. / Max., Min. / Max.mold thickness⑥ 最小 / 最大注塑机开档— open daylight Min. / Max.⑦ 锁紧行程— clamp stroke⑧ 锁紧力— clamping force⑨ 顶出行程— ejector stroke⑩ 顶出力— ejector force !你想成为学霸吗。
- 1、下载文档前请自行甄别文档内容的完整性，平台不提供额外的编辑、内容补充、找答案等附加服务。
- 2、"仅部分预览"的文档,不可在线预览部分如存在完整性等问题,可反馈申请退款(可完整预览的文档不适用该条件!)。
- 3、如文档侵犯您的权益，请联系客服反馈,我们会尽快为您处理(人工客服工作时间：9:00-18:30)。
ejector bushing
保压过程
Packing Process
ejector guide pillar
保压阶段
Packing stage
cold-slug well
保压时间
packing time
male mold face
潜流效应
underflow effect
mold temperature
gate
多点进浇
multiple gating
gate length
牛顿流体
Newtonian fluid
Gate location
非牛顿流体
non-Newtonian fluid
insert
非均匀收缩
Non-uniform Shrinkage
heel lock
喷嘴
nozzle
cavity plate
脱模
demolding
脱模斜度
draft
脱模困难
ejection difficulties
内应力
internal stress
长链高分子
long chain macromolecules
凝固层比例
frozen layer fraction
取出
removal
ห้องสมุดไป่ตู้
粗加工
rough machining
伺服马达
core-retainer plate
斜度
draft angle
母模面
Famale mold face
动模面
dynnamic mold face
斜槽导板
finger guide plate
推杆固定板
ejector retainer plate
注射系统
injection system
模内压力
intemal mould pressure/cavity pressure
定压冷却阶段
isobaric cooling
各向同性
isotropic
坚韧
tough
体积收缩率
volume shrinkage
体积特性
wolumetric Properties
中文术语
品质 公差 不良标签 标示单 整理
整顿
清扫
清洁
教养
安全
来料不良 刮伤 压痕 螺栓 热注射成型 控制面板 显示器 安全门 注射座 螺杆 料膛 加热圈 喷嘴 定模板 动模板 成型机顶杆 手动操作 半自动操作 全自动操作 料膛清洗 上料机 温调机 参数监控画面 生产管理画面 模板控制画面 顶出控制画面 加热管理画面 注射速度画面 注射压力画面 保压控制画面 计量控制画面 报警显示画面 最大高度 最小高度 锁模力 锁模系统 控制系统 抽芯距 抽芯力 生产周期 液压系统 短射 喷射 白化 缩痕 收缩差异 熔接线 亮线 冷熔接
纤维
fibers
添加剂
filler
流动充填方式
filling pattern
充填过程
filling process
充填速率
filling rate
充填阶段
filling stage
充填时间
filling time
注射力
ejection force
体积
free volume
弯曲
Flexural
流动平衡
斜销
angle pin / finger cam
熔体流动速度
MFR
斜滑块
angled-lift / splits
微观结构
microstructure
悬臂搭扣连接 模套 型芯 支架 推块 推杆 推板 复位杆 浇口尺寸 直接浇口 盘式浇口 侧浇口 扇形浇口 浇口镶块 圆柱头推杆 扁顶杆 连接推杆 导套 导柱 浇口 浇口长度 浇口位置 嵌件 楔紧块 凹模 凹模拼块 定模座板 顶出系统设计 顶出时间 推板导套 推板导柱 冷料穴 公模面 模具温度 支撑板 隔板 掏空
成型压力
moulding pressure
ejector tie rod
活动镶件
movable insert ,loose detail
guide bush
动模
movable mould / moving mould
guide pillar
动模座板
moving clamp plate / bottom clamp plate
flow balance
流动控制
flow control
流动长度
flow length
流长比
flow length to thickness
流动趋向
flow orientation
流动模拟
flow simulation
圆形流道
Full-round runner
三角筋
Gussets
半圆形流道
Halforound runner
clamping force clamping system control system core-pulling distance core-pulling force Cycle time hydraulic system short shot jetting
shrinkage asymmetric shrinkage lines color change Cold welding
servomotor
工序
workstage
塑料件
plastic parts
注射模
injection mould
冲击强度
Impact strength
模内收缩
in mold shrinkage
流动方向的收缩率 in-flow shrinkage
注射压力
injection pressure
注射速度
injection speed
edge gate
热固性塑料模具 mould for thermosets
fan gate
开模力
mould opening force
gating insert
模板
mould plate
ejector pin with cylindrical head 闭合高度
mould shut heihgt
flat ejector pin
喷嘴压力曲线
nozzle pressure profile
cavity splits
过保压
overpack
fixed clamp plate
保压模拟
pack simulation
ejection system design
保压流动
packing flow
ejection time
保压压力
packing pressure
锥形定位件
mould ases locating elements
Gate dimensions(sizes)
模架（注射模） mould bases
direct gate;sprue gate
塑料成型模具
mould for plastics
disk gate
热塑性 塑料模具 mould for thermoplastics
冷却不均
uneven cooling
backing plate / support plate 均匀度
uniformity
baffle
阀式浇口
valve gate
core out
排气槽
vent (of a mould)
型心拼块
core splits
强度设计
Design for strength
型芯固定板
静置段 保压时间 料斗
holding stage holding time hopper
烧焦
burn marks
色差
discoloration
脆化
brittleness
蠕变
Creep
位移
Displacement
分层表面剥离
delamination
三角洲效应
delta effect
方向收缩
diectional shrinkage
困气
烧伤 黑斑 料纹
注塑行业术语中英文对照
英文术语 quality tolerance defective product label identifying sheet list Seiri
Seiton
Seiketsu
Seiso
Shitsuke
Safe deficient purchase scratch dents bolt thermoplastic injection contorl plat pro-face saft door enjection blend screw fabbrel heater nozzle plam moving plam ejector pin man sengle man auto purge loader
弧
arc
制品产品
article
轴
axis
钳工工作
bench-work
坯料
blank
黄铜
brass
毛刺
burr
铸钢
cast steel
压板
clamp
轮廓
contour
制图
drawing
点火花加工
electrochemical machining
电极
electrode
套管
ferrule