机械类常用英语词汇大全

机械类常用英语词汇大全一字螺丝批 slot type screwdriver 一点透视 one-point perspective二画二合一黏合剂 epoxy resin adhesive 二合胶；混合胶 epoxy glue二维的；平面的 two-dimensional二进制 binary二极管；整流子 diode二号螺丝攻 second tap二路开关 two-way switch十进制的；公制的 metric人工制品 artefact人造板 man-made board人体工程学 ergonomics; humanengineering人体尺寸 human dimension人体测量学 anthropometry;anthropometrics刀片 blade刀身 blade刀具 tool刀具溜座 carriage刀柱 tool post刀架 tool rest刀架底座 tool rest bracket刀座帷；床鞍 apron刀座鞍；溜板座 saddle力 force力三角形 triangle of force力平行四边形 parallelogram offorce力多边形；多边形力学 polygon offorce力的分解 force resolution力架；亮漆 lacquer力矩 moment力偶 couple力矩定律 law of moment力-距离图表 force-distance graph力图 force diagram力线 line of force力点 effort十字榫 cross halving joint十字螺丝 Philip s head screw十字螺丝批 Philip s typescrewdriver丁字尺；T 尺 tee square三画三爪夹头 three-jaw chuck三角尺 set square三角形结构系杆 triangulation tie三角锉 triangular file三维的；立体的 three-dimensional 三氯甲烷；哥罗芳 chloroform三聚氰胺；蜜胺 melamine三点透视 three-point perspective上油漆 painting上釉 enamelling凡立水 varnish叉形顶尖 fork centre口罩 mask士力；虫漆 shellac士巴拿；扳手 spanner大芯夹板；宽条芯夹板 blockboard; solid corestock-laminated board大量制造 mass production子口刨；槽口刨；边刨 rebate plane小型平槽刨 miniature router plane小型线料弯曲器 small wire bender小型弯折机 mini bender小型电路断路器；跳菲 miniature circuitbreaker (MCB)小齿轮 pinion山樟 San Cheong工件 workpiece工字梁 I beam工作面 working surface工作图；制作图 working drawing工作台 bench; working table工具 tool工具贮存室 tool storage工具槽 well工具钢 tool steel工场 workshop工场安全 workshop safety工程字书写技巧 lettering工程系统 engineering system工程绘图 engineering drawing工业酒精；火酒 methylated spirit 弓形手钻；手摇曲柄钻 brace弓形手钻嘴 brace bit弓锯 bow saw; hacksaw弓锯片 hacksaw blade弓锯床 hacksawing machine四画不平衡 imbalance不含铁金属；非铁金属 non-ferrousmetal不贯穿孔；闭孔；盲孔 blind hole不贯穿鸠尾榫 lapped dovetail joint不对称 asymmetry不锈钢 stainless steel不稳定平衡 unstable equilibrium中心 centre中心线 centre line中心冲 centre punch中心钻 centre drill中心钻嘴 centre bit中央处理器 central processing unit(CPU)中性 neutral中性平衡；随遇平衡 neutralequilibrium中性轴 neutral axis中密度纤维板 medium density fibre board(MDF)中粗锉纹 second cut中碳钢 medium carbon steel中线 neutral wire互补金属氧化物半导体 complementary metal oxide semiconductors (CMOS)介子；垫片 washer介指铁 ring mandrel介电常数；电容率 permittivity介稳态的；亚稳态的 metastable内力 internal force内卡尺 inside calipers内能 internal energy内涵性质 intensive properties内圆弯凿 scribing gouge内锁式配件 interlocking fitting内燃机 internal combustion engine内螺纹制造法 tapping内螺丝 internal thread内弯边 concave edge六角金属枝 hexagonal bar六角匙 Allen key六角头螺丝 hexagonal head screw 公制的；十进制的 metric公差 tolerance冗余构件 redundant member分力 component force分子 molecule分子力 molecular force分切；分割；切断 parting off分贝 decibel分析 analysis分析及批判学 analytical and criticalstudies分析器 analyzer分流器 shunt分界面；界面；接口 interface分厘卡 micrometer分规 divider分割车刀架 parting tool holder分解 decomposition分压器 potential divider; voltagedivider隔离开关 isolating switch切削工具 cutting tool切削液 cutting fluid切削深度 depth of cut切屑；碎屑 chip切线锯法 tangential sawing切辊纹；滚纹 knurling切断；分切；分割 parting off切断工具 parting tool勾；勾脚 hook勾刀；胶片刀 plastic cutter化胶水 tensol反向偏压 reverse biased反相放大器 inverting amplifier反相器 inverter反射 reflection反电动势 back e.m.f.反馈；回输 feedback天拿水；稀释剂 thinner天梯牙；齿条 gear rack天然木材 natural timber天然干燥法 air seasoning孔隙率 porosity尺寸 dimension尺寸线 dimension line尺身 blade引力；重力 gravitational force 心形凸轮 heart-shaped cam心材 heartwood心轴 mandrel心销 core pin手工具 hand tool手工锯 junior hacksaw手削法 paring手持虎钳 hand vice手柄 handle手套 gloves手扫漆 brushing lacquer手推车 barrow手提式竖线锯 portable jigsaw 手提电动工具 portable power tool 手提电钻 electric hand drill手进给 hand feed手摇曲柄钻；弓形手钻 brace手摇钻 hand drill手锉 hand file手锯；板锯 handsaw手锥 bradawl手辘轧机 hand rolling machine支柱；支撑物 strut支架；支座 support支点 fulcrum; pivot文字 text方向 direction方向针 pointing needle方枝 square bar方波形 square waveform方波产生器 squarer方型牙板 rectangular die方格纸；网格纸 grid paper方通 square tube方块图 block diagram方锉 square file方头钻嘴 square shank bit方螺帽 square nut方边凿；直边凿 firmer chisel木 wood木工 woodwork木工工作间 woodwork area木工工作台 woodworker s bench木工车床 wood turning lathe;woodworking lathe木工铅笔 carpenter s pencil木工刨床 thicknessing and planningmachine木牙螺丝；木螺钉 wood screw木材 timber木材车削 wood turning木材车削工具 wood turning tools木屑压合板；万花板 chipboard木条接榫 corner strip joint木圆头槌 doming mallet木模；模型 patterns木线 wood strip木胶粉 ureaformal dehyde resin glue木锉 rasp木螺钉；木牙螺丝 wood screw木槌 mallet止推轴承 thrust bearing止推垫圈 thrust washer比例 proportion比例尺 scale比例常数 proportionality constant 比例极限 proportional limit比较器 comparator比热容量 specific heat capacity 水平投影面 horizontal plane水平仪；平水尺 spirit level水气掣；漏电断路掣 earth leakage circuit breaker (ELCB)水晶胶；聚酯树脂 polyester resin水晶胶的铸造成形 resin casting水磨砂纸 silicon carbide paper火叉 firing fork火水；煤油 kerosene火牛；变压器 transformer火石轮 grinder火花电蚀法；放电极加工 electrical discharge machining火酒；工业酒精 methylated spirit火钳 tongs火线；活线 live wire火砖 fire brick爪扣；爪形离合器；犬齿式离合器 dogclutch牙板；丝模 die牙板扳手；丝模扳手 die holder(stock)牙板螺帽 die nuts牛皮胶；动物胶 animal glue牛油纸 tracing paper牛顿运动定律 Newton s laws ofmotion犬齿式离合器；爪扣；爪形离合器 dogclutch注射成形法；喷射铸造法injection moulding并激电动机；并绕电动机shunt-wound motor乳酪胶casein glue乳胶漆emulsion paint亚加力；压克力；聚甲基丙烯酸甲脂acrylics; polymethyl methacrylate (PMMA)亚稳态的；介稳态的metastable来回摆动oscillating两点透视two-point perspective刻度；划线ruling刺冲dot punch刮刀scraper刮擦scraping制动鼓drum brake制动碟disc brake制动器brake受迫振动forced vibration受迫振荡forced oscillation和谐harmony周转齿轮；行星齿轮epicyclic gear固定夹；台夹bench holdfast固定负载dead load定子stator定位销；合钉dowel定位螺丝set screw定距轮stitch marker屈片机folding machine屈曲bending屈服点；降服点yield point屈圈法loop forming屈卷法scrolling屈接缝folded lap seam屈喉机tube bender屈折folding屈折线folding line屈压接缝folded & grooved seam延性ductility 延性的ductile弦锯法plain sawing弧口凿；圆凿gouge往复式运动reciprocatory motion拉力tensile force拉力计；张力计tensiometer; tensometer拉钉blind rivet; pop rivet拉钉接合blind riveting; pop riveting拉钉钳blind riveting pliers; pop riveting pliers拉张tension拉张应力tensile stress拉张应变tensile strain拉细drawing-down拉制法drawing拉线wire drawing「披」口；利口；铁屑burr拔钳nippers抛光buffing抛光机buffing machine放大；扩大enlargement放大尺pantograph放大倍数amplification factor放大器amplifier放电极加工；火花电蚀法electrical discharge machining易用万能尺line setter易碎fragile〈绘画的〉明暗运用；描影shading枝；杆rod杯形顶尖cup centre杯头螺丝hexagonal socket head cap screw 板锯panel saw松木pine松节水turpentine法式磨光French polishing法拉〈电容量单位〉farad油石；磨刀石oil stone油漆；涂料paint泡沫塑料；多孔塑料；海绵状塑料foam plastics物理特性physical property物理属性physical attribute物理量physical quantity盲孔；闭孔；不贯穿孔blind hole直尺ruler; straight rule直角叉榫corner bridle joint直角尺try square直角板；角板angle plate直角杠杆bell crank lever直身钻嘴straight shank drill直车刀架straight tool holder直流发电机d.c. generator直流电流direct current (d.c.)直流电动机；直流马达 d.c. motor直纹锯rip saw直线切削linear interpolation直线运动rectilinear motion直边凿；方边凿firmer chisel直铁剪straight snips硅silicon空行程idle stroke空气动力学aerodynamics空间space空载no load花纹凿embossing stamp花梨木rosewood花样；图案pattern虎克定律Hooke s Law虎钳vice虎钳护罩vice clamp初步意念proposed solution表面surface表面展开图surface development表面张力surface tension表面处理surface finishing; surface treatment表面硬化case hardening表面硬化钢case-hardened steel表达方式presentation表达技巧；传意技巧communication technique表观膨胀；视膨胀apparent expansion金工metalwork金工工作间metalwork area金工角尺engineering square金工车床metalwork lathe 金工虎钳engineer s vice金工锯床power hacksaw金属包头；金属箍ferrule金属配件metal fittings金属线wire金属压展机hand rolling mill金属擦光剂；磨光剂metal polish金属薄片sheet metal金属键metallic bond长方通rectangular tube长刨trying plane长螺旋钻咀long auger bit长镗孔long boring闸极gate阻抗impedance附件attachment附录appendices青铜bronze非反相放大器non-inverting amplifier非本征半导体extrinsic semiconductor非破坏性试验non-destructive testing非晶状固体amorphous solid非顽磁性铁磁材料non-retentive ferromagnetic material非压缩性流体incompressible fluid非稳态unsteady state非铁金属；不含铁金属non-ferrous metal 九画亮漆；力架lacquer信号signal信号产生机signal generator信号处理signal processing保养；维修maintenance保险丝fuse保护罩；保护网；防护装置guard; safety guard促凝剂accelerator削屑swarf垂直投影面vertical plane型砧swages〈书的〉封皮binding封面cover急回机构quick return mechanism扁枝bar扁头cross-pein扁头法upsetting扁头铆钉flat head rivet扁头螺丝flat head screw扁凿flat chisel指示器indicator指形榫finger joint施力effort染色staining染色剂stain架构framework柄stock柚木teak柳安木lauan流程图flow chart洗漆水paint remover活塞piston活塞销gudgeon pin活线；火线live wire炮铜gun metal玻璃砂纸glass paper玻璃胶silicon sealant玻璃纤维glass fibre玻璃纤维席glass fibre mats界面；分界面；接口interface相差phase difference相对密度relative density砂布emery cloth砂磨sanding砂磨纸abrasive paper砂磨机sander砂铸；砂铸模sand casting研究探讨research研磨；磨削grinding研磨角grinding angle科技technology科技研习technological studies科学知识scientific knowledge科学瓷；聚氰胺毋醛树脂melamine-formaldehyde resin (MF)红铜垫圈copper washer 美学aesthetics耐火胶板fire-resisted laminate耐火砖refractory block耐冲击聚苯乙烯high impact polystyrene 背back胡桃木walnut范德华引力Van der Waals force英制惠氏标准螺纹British Standard Whitworth thread (B.S.W.)苯乙烯丙烯共聚物styrene-acrylonitrile copolymer苯酚甲醛phenol formaldehyde (PF)计；规gauge定时器timer计划planning计算器；计算机computer计算器辅助工程computer-aided engineering (CAE)计算器辅助控制computer-aided control计算器辅助设计computer-aided design (CAD)计算器辅助制造computer-aided manufacturing (CAM)计算器数控computer numerical control (CNC)负反馈；负回输negative feedback负极；阴极cathode负载load轨路式砂纸磨机orbital sander重力；引力gravitational force重心centre of gravity重量weight重锉法heavy filing限制开关；极限掣limit switch限流器current restrictor降服点；屈服点yield point降压器step down transformer面plane面心；形心centroid面材plane materiel面板face plate面板车削法face plate turning面结型晶体管junction transistor面罩face mask音量volume页边margin风车锯；圆盘锯circular saw风格style风煤炉forging hearth飞轮flywheel飞机木；菠萨轻木balsa首版；原型；雏形prototype恒温器；温度调节器thermostat十画俯视图；平面图plan倒角；去角chamfer倒模成形；模塑；铸模成形moulding修边trimming修边机trimmer剖切面cutting plane剖切面线cutting plane line剖面；纵切面section剖视图sectional view剖线hatching line刚性；刚度rigidity刚性模量；刚性模数modulus of rigidity 刚强度；硬挺度stiffness刚体rigid body原子粒；晶体管transistor原色primary colour原型；雏形；首版prototype原料raw material哥罗芳；三氯甲烷chloroform埋头直孔counterbore埋头铆钉countersink head rivet埋头锥孔countersink埋头螺栓countersink head bolt埋头螺丝countersink head screw埋头钻countersink drill埋头钻嘴countersink bit; rose countersink drill套筒；套管sleeve套锤fullers家用的domestic展性malleability 展性的malleable展开图development峰至峰值peak-to-peak value峰值peak value差动放大器；微分放大器differential amplifier徒手草图freehand sketch径线锯法radial sawing径锯法quarter sawing振动vibration振幅amplitude振荡oscillating振荡运动oscillatory motion振荡器oscillator效率efficiency时效硬化age hardening时间常数time constant框架frame气动的系统；气压的系统pneumatic system 气动控制pneumatic control气阀gas valve气焊gas welding空气压缩air compression氧乙炔焊接oxy-acetylene welding氧化oxidation; oxidize消失点vanishing point消色差achromatic colour浸涂dip coating海绵状塑料；泡沫塑料；多孔塑料foam plastics浮力buoyancy浮雕relief特性property珠光体pearlite疲劳fatigue真空成形；真空吸塑vacuum forming真空成形机vacuum former真空吸塑成形法vacuum moulding真实形状true shape矩波形rectangular waveform纹理grain级联系统cascade system纸板carton board脆弱的；易碎的brittle脆性brittleness脉冲pulse能量守恒conservation of energy能量守恒定律law of conservation of energy草图sketch草图画纸layout paper草稿draft衰减attenuation起化magnetization起泡剂；发泡剂foaming agent起动扭矩starting torque起动器starter起磁；磁化magnetization退化degradation退火annealing配件fitting钉合nailing钉钳；铁钳pincers钉冲nail punch钉锤cross-pein hammer针尖point针叶needle-point leaf针叶树coniferous tree针锉；杂锦锉needle files马氏体martensite马达；电动机；摩打motor马粪纸straw board骨架结构carcase construction容差；宽裕度allowance高密度聚乙烯high density polyethylene (HDPE)高通滤波器high-pass filter高速钢high speed steel机械类常用英语词汇大全4十一画干燥法；干材法 seasoning偶合；耦合(电工) coupling侧面投影 side projection侧条芯夹板 laminboard侧视图；端视图 end elevation; endview偏心凸轮 eccentric cam偏向 bias; deviation偏差 deviation偏压 bias偏离 drift剪刀 scissors剪力 shearing force剪切 shear剪床；闸床 guillotine对角剪钳 diagonal cutting pliers动力工具 power tool动力学 dynamics动物胶；牛皮胶 animal glue动圈式电流计 moving coilgalvanometer动态；运动 movement动态平衡 dynamic equilibrium动摩擦 dynamic friction; kineticfriction匙孔锯 key-hole saw; pad saw只读存贮器；只读存储器 read only memory(ROM)国际标准组织 The InternationalStandard Organization (ISO)基本设计原理 design fundamentals基极电流 base current基准边 true edge基尔霍夫定律；克希何夫定律 Kirchhoff sLaw密度 density常规 conventions带式砂磨机 belt sander带式传动 belt drive带通滤波器 band-pass filter带锯；运锯 band-saw张力计；拉力计 tensiometer;tensometer强化 reinforcement强化塑料 reinforced plastics彩度 chroma控制系统 control system卷尺 flexible rule; tape rule接口；界面；分界面 interface接合 joining接合工具 joining tool接地 earthing接缝 lapped seam; seam接触角 angle of contact扫上光油 varnishing推拔车削 taper turning推进器 propeller斜切车刀 skew turning chisel斜投影 oblique projection斜角 mitre斜角；斜面 bevel斜角规 bevel; sliding bevel斜角榫 mitre joint斜身螺丝攻 taper tap斜格纸；等角投影纸 isometric gridpaper〈织物的〉斜纹 bias斜钉法 dovetail nailing斜率 gradient斜视图 oblique drawing斜榫尺 mitre square斜榫规 mitre gauge斜槽位；鱼尾槽位 dovetail trench 斜边凿 bevel edged chisel旋扭法 twisting旋钮；球形把手 knob旋制法 spinning旋转；转动 rotation旋转台 rotating platform旋转轴 rotating shaft旋转运动 rotary motion杆；枝 rod条线图；棒形图 bar chart梨形凸轮 pear-shaped cam液相 liquid phase液晶体显示 liquid crystal display(LCD)液压 liquid compression液压控制 hydraulic control液压机 hydraulic press添加法；加成作业 addition process添加剂 additive清漆 varnish清胶 gel resin混合胶；二合胶 epoxy glue深拉制法 deep drawing深度计；深度规 depth gauge淬火 quench淬火液 quenching liquid淬硬 quench hardening焊接 welding焊枪 brazing torch焊剂 flux焊炉 brazing hearth球形把手；旋钮 knob球体 sphere瓷釉；搪瓷；珐琅 enamel瓷漆；磁漆 enamel paint产品设计规格 product designspecification (PDS)眼罩 goggles硫化作用 vulcanization移印字 dry rub on transfers第一角投影法 first angleprojection第三角投影法 third angleprojection符号 symbol粗削 roughing粗纹 bastard cut粗刨 jack plane统一〈设计〉 unity组件 component; module组合角尺 combination square组合钳 combination pliers组合图；装配图 assembly drawing 汇编语言；汇编语言 assemblylanguage组合逻辑 combinational logic组成物料 component material组织原理(设计) organisation脱碳 decarburization脱模剂 release agent脱模腊 mould release wax茎 stem蛋形木槌 bossing mallet规；计 gauge规身 stock规柄 stem规格 specification许可应力 permissible stress设计 design设计元素 design element设计作业；专题设计研习 designproject设计师 designer设计记录档案 design folder设计组织 design organization设计处境；设计环境 design situation 设计规格 design specification 设计提案 design proposal设计程序 design process设计概要；设计纲要 design brief设计解决方法 design solution贯穿鸠尾榫 through dovetail joint软木 softwood软板；绝缘板 soft board软胶；聚乙烯 polyethylene (PE)软焊 soft soldering软焊料 soft solder软钢 mild steel通用面板 universal surface plate 连接杆；连杆 linkage连结板 web连续插图 sequential drawing速度 velocity速度比 velocity ratio造形 form造型砂 moulding sand透明；通透 transparent透视投影 perspective projection透视法 perspective透视图 perspective drawing131闭孔；盲孔；不贯穿孔 blind hole 闭合电路 closed circuit死循环控制 closed-loop control 死循环控制系统 closed controlsystem死循环增益 close loop gain阴极；负极 cathode陶瓷 ceramics陶瓷制品 ceramic product顶尖 centre顶面投影 top projection顶脱销 ejector pin鱼尾半接榫 dovetailed tee halvingjoint鱼尾榫；鸠尾榫；燕尾榫 dovetailjoint鱼尾槽位；斜槽位 dovetail trench麻花钻 twist drill梣木 ash焗炉 oven焓 enthalpy十二画家俬钉 panel nail家俬蜡 furniture wax伞齿轮 bevel gear最后方案 final solution割线规 cutting gauge喇叭；扬声器 speaker单元 module单板；薄木皮 veneer单板镶贴；薄皮镶合 veneering单相 single phase单脚规 odd-leg calipers单路开关 one-way switch单鸠尾榫 single dovetail joint单碟离合器 single plate clutch单稳态 monostable喉管 tube围裙 apron循环车削 turning cycle循环过程 cyclic process惠斯登电桥 Wheatstone bridge惰轮 idler描影；(绘画的)明暗运用 shading插座 socket插头 plug换能器；转能器；传感器 transducer扬声器；喇叭 loud speaker; speaker晶粒 grain晶体 crystal晶体振荡器 crystal oscillator晶体结构 crystal structure晶体管；原子粒 transistor晶体点阵；晶体格构；晶格 crystallattice棘轮和爪 ratchet and pawl棘齿 ratchet棘齿弓钻 ratchet brace壳型模塑 shell moulding光标卡尺 vernier calipers减除作业 reduction process涡流 eddy current涡轮机 turbine测径器 calipers测试工具 testing tool焦炭 coke无功分量；抗性分量 reactivecomponent无彩色 achromatic colour无头螺丝 grub screw无压释放器 no-voltage release无稳态定时器 astable timer无稳态电路 astable circuit无稳态多谐振动器；无稳态多谐振荡器；无稳态复振器 astable multivibrator然纳二极管；齐纳二极管 Zener diode 珐琅；搪瓷；瓷釉 enamel画板；绘图板 drawing board画纸 drawing paper发光二极管 light emitting diode(LED)发泡聚苯乙烯；发泡胶 expandedpolystyrene (EPS); styrofoam发泡剂；起泡剂 foaming agent发电机 generator发热管 heating tube发热线切割机 hot wire cutter发热线机 hot wire machine; stripheater短路 short circuit硬化 hardening硬化剂 curing agent; hardener;hardening agent硬木 hardwood硬件〈计算机〉 hardware硬度 hardness硬度测试 hardness test硬挺度；刚强度 stiffness硬焊 hard soldering硬模铸造；压力铸造；压铸 die casting 硬胶；聚苯乙桸 polystyrene (PS)硬质纤维板；「快把」板 hardboard程序；程序 program稀释剂；天拿水 thinner等角投影 isometric projection等角投影纸；斜格纸 isometric gridpaper等角投影图；均角投影图 isometricdrawing等角轴 isometric axis等角圆 isometric circle等和色；合成色 secondary colour等焓的过程 isentropic process筒夹；弹性夹头 collet 筒形线圈；螺线管；电磁线圈 solenoid结构 structure结构力学 structural mechanics结构木材 structural timber绝缘 insulation绝缘板 insulation board绝缘体 insulator丝攻扳手 tap wrench丝模；牙板 die丝模扳手；牙板扳手 die holder(stock)菠萨轻木；飞机木 balsa虚线；隐线 hidden line视查 visual inspection视膨胀；表观膨胀 apparent expansion评估 evaluation评鉴 criticism象限 quadrant超塑料 superplastic超载 overload超声波 ultrasonic wave超声波测试 ultrasonic test轴 shaft轴心车削法 turning between centres轴功 shaft work轴承 bearing轴接 coupling轴环；卡圈 collar周期 period进料螺杆 feed screw进给 feed进给速率 feed rate进给螺杆 feed screw量角器 protractor量度 measurement量度工具 measuring tool钝 blunt开口式槽榫 through housing joint 开口扁钳 open mouth tongs开口销 cotter pin开孔凿 hole punch开材方法(木材) conversion开环控制系统 open-loop controlsystem阳极；正极 anode阳极氧化法；阳极处理 anodizing集成电路 integrated circuit (IC)集电极电流 collector current云尺；云板；曲线规 French curve云母 mica韧皮部 bast韧性 toughness顺磁性 paramagnetic material黄金分割 golden section黄金比例 golden ratio黄铜 brass黑皮软钢 black mild steel十三画传动系统drive system传动螺杆drive screw传意技巧；表达技巧communication technique传感器；换能器；转能器transducer传热性conductivity of heat传导conduction传导性conductivity倾角angle of inclination; rake angle倾斜面inclined plane势能；位能potential energy势梯度；位梯度potential gradient汇编语言；汇编语言assembly language圆口夹钳round tongs圆形及椭圆形尺circle and ellipse guide圆形凸轮circular cam圆形开口牙板circular split die 圆咀钳round nose pliers圆底弯刨round faced spokeshave圆弧运动circular motion圆枝round rod圆规compasses圆通；圆管round tube圆折边beaded edge圆盘锯；风车锯circular saw圆锉round file圆头弧刀round nose gouge圆头铆钉conical head rivet; round head rivet圆头螺丝round head screw圆头铁锤ball pein hammer; raising hammer圆瓣图pie chart圆铁砧bick iron圆凿；弧口凿gouge塞子plug塞状螺丝攻plug tap塑性plasticity塑性形变plastic deformation塑料plastics塑料土；橡皮泥plasticine塑料涂层plastic coating塑料层积片；层叠塑料片laminated plastic sheet涂料；油漆paint涂层金属片coated metal sheet塔轮cone pulley填角焊接fillet weld填料；填剂filler奥氏体austenite微分放大器；差动放大器differential amplifier微电子学microelectronics微调fine-adjustment溜板座；刀座鞍saddle详细图；零件详图details drawing意念；构想idea感温开关temperature sensitive switch感应电路sensor circuit感应器sensor搪瓷；珐琅；瓷釉enamel计算机辅助设计与制造系统CAD/CAM system计算机数控computer numerical control (CNC)计算机数控车床CNC lathe电路circuit电磁线圈；筒形线圈；螺线管solenoid电枢；衔铁线圈armature电线electric wire电线退皮钳wire stripper电导率electrical conductivity电导量conductance电压voltage电压比voltage ratio电压比较器voltage comparator电压放大voltage amplification电压放大器voltage amplifier电压表voltmeter电压降voltage drop电压调节器voltage regulator电镀electroplating电钻electric drill零件；组件component零件分散图；爆炸图exploded drawing (view)零件表parts list零件详图；详细图details drawing零件图parts drawing零位校正zero correction顽磁性铁磁材料retentive ferromagnetic material饱和度saturation鸠尾榫；鱼尾榫；燕尾榫dovetail joint鸠尾榫锯dovetail saw鼓式制动器drum brake鼓风炉blast furnace十四画划针scriber划线layout; marking out; ruling划线刀marking knife划线工具marking tool 划线规marking gauge; surface gauge划线轮stitch marker图形表达技巧graphic presentation technique图案；花样pattern图框drawing frame图画的阴暗部shade图画纸cartridge paper图象传意graphical communication图头钉French nail垫片；垫圈；介子gasket; washer垫板；台垫bench hook垫料backing实践计划realization对比contrast对流convection对接butt对接合；对接榫butt joint对接角榫butt mitred joint对接焊butt welding对称symmetry惯性力矩；转动惯量moment of inertia惯性负载inertia load截锥铆钉pan head rivet折尺folding rule折床；弯曲机bending machine折铁砧hatchet stake折铁器folding bar敲打成形beatening杠杆lever构件member构成作业fabrication process构架接合；构架榫framed joint构架结构frame construction构想；意念idea榫头tenon榫眼；卯孔mortise榫规；双线规mortise gauge榫锯；夹背锯tenon saw榫凿mortise chisel槌击法chopping演绎技术(设计) rendering technique滚子轴承roller bearing滚花身；压花身knurled shank滚珠轴承ball bearing滚纹；切辊纹knurling滚动摩擦rolling friction滚压；辘压rolling漏电断路掣；水气掣earth leakage circuit breaker (ELCB)滞后现象hysteresis渗碳cementation熔化fusion熔渣slag熔焊接fusion welding磁化；起磁magnetization磁化电流magnetizing current磁性magnetic property磁场magnetic field磁场强度magnetic field strength磁漆；瓷漆enamel paint磁铁magnet碟式制动器disc brake碟式离合器；盘式离合器plate clutch碟形凹陷法sinking碳化三铁体cementite碳化合金carbide碳钢carbon steel端面车削facing端纹end grain端视图；侧视图end view管pipe综合synthesis网格grids网格纸；方格纸grid paper网络；网络network；web149维修；保养maintenance聚乙烯；软胶polyethylene (PE)聚丙烯；百折胶；百折胶polypropylene (PP)聚四氟乙烯polytetrafluoroethylene (PTFE) 聚甲基丙烯酸甲脂；压克力；亚加力polymethyl methacrylate (PMMA)聚合作用polymerization聚合物polymer聚苯乙烯；硬胶polystyrene (PS)聚氨基甲酸乙酯polyurethane (PU) 聚硅铜橡胶silicon rubber聚氯乙烯；PVC胶polyvinyl chloride (PVC)聚酯polyester聚酯树脂；水晶胶polyester resin聚碳酸酯polycarbonate (PC)聚醯胺；尼龙polyamide (PA)腐蚀corrosion腐蚀液corrosive liquid蒸气steam蜜胺；三聚氰胺melamine蜜胺甲醛melamine formaldehyde (MF)蚀刻术etching制成板manufactured board制作过程working process制作图；工作图working drawing制造方法production method制图；绘图drawing诱导抗力induced drag辅助投影auxiliary projection轻锉法light filing远景perspective酸洗acid pickling铰hinge铰刀reamer铰孔reaming铰接合hinged joint铰接式支座hinged support银silver银焊料silver solder铜；红铜copper铜焊brazing铜焊料；锌焊料spelter solder铬chromium铣milling铣刀milling cutter铣床milling machine阀门valve隙角clearance angle雌雄榫；榫卯mortise and tenon joint齐纳二极管；然纳二极管Zener diode劈刀riving knife劈尖；楔wedge喷咀nozzle喷砂sand blasting喷射铸造法；注射成形法injection moulding喷漆法spraying增强剂reinforcing agent增塑剂plasticizer宽条芯夹板；大芯夹板blockboard宽裕度；容差allowance层积；层叠laminating层叠塑料片；塑料层积片laminated plastic sheet废木waste wood弹性elasticity弹性夹头；筒夹collet弹性形变elastic deformation弹性常数elastic constant弹性极限elastic limit弹性模量；弹性模数modulus of elasticity 弹性应变能elastic strain energy弹簧spring弹簧分规spring divider弹簧垫圈spring washer耦合；偶合(电工) coupling胶片刀；勾刀plastic cutter摩打；电动机；马达motor摩擦力friction摩擦焊接friction welding挠曲机；折床bending machine挠性联轴节flexible coupling挠度deflection数字冲number punch数字及字母冲number and letter punch数字仿真转换；数模转换digital-to-analogue conversion数码化仪器；数字式仪器digital instrument 数码化显示；数字式显示digital display 数据搜集；搜集资料data collection调制解调器modem暂时接合temporary joint样式；模式pattern枢接结构pin-jointed structure枢轴；支点pivot标示尺寸dimensioning 标度scale标量scalar标准尺寸；市售尺寸stock size标准横切面standard cross-section槽groove槽口rebate槽口刨；边刨；子口刨rebate plane槽位trench槽沟平接榫tongue groove joint槽沟角接榫tongued trenched joint槽刨；槽刨机router槽榫housing joint模die; former模子；铸模mould模件；模块；组件module模式；样式pattern模板template模型model; patterns模型制作model making模塑；倒模成形；铸模成形moulding模数转换；仿真数字转换analogue-to-digital conversion仿真simulation仿真系统analogue system模锻法；锤锻法；冲锻法drop forging梁规trammel欧姆定律Ohm s Law欧姆计ohmmeter欧姆导体ohmic conductor潜热latent heat潜变；蠕变creep润滑lubrication润滑脂grease润滑剂lubricant熟铁wrought iron热工及冷工凿刀hot and cold set热加工；热作工hot working热加工硬化hot work hardening热收缩thermal contraction热均衡图thermal equilibrium diagram热固性塑料thermosetting plastic热的特性thermal property热轧压hot rolling热流heat flow热风炉hot blast stove热浸法hot dipping热能heat energy热动式超载继电器thermo overload relay 热敏电阻thermister热处理heat treatment热绝缘thermal insulation热传递heat transfer热塑性塑料thermoplastic热导率thermal conductivity热膨胀thermal expansion盘式离合器；碟式离合器plate clutch窑房干燥法kiln seasoning箱carcase编码encode编码器encoder编译器；编译程序compiler线材linear materials线性收缩linear contraction线性运动linear motion线性膨胀linear expansion线状结构linear structure线锯床；线锯机jigsaw线锯coping saw缓冲板buffer board缓冲器buffer胶合板；夹板plywood胶合剂；黏结剂adhesive胶纸adhesive tape; tape蜗杆worm gear蜗杆和蜗轮worm and worm wheel蜗轮worm wheel冲punch冲子punch冲孔；切料blanking冲胚；毛坯blank冲程stroke冲量impulse冲压stamping冲压工具stamping tool冲压法pressing冲击impact冲击强度impact strength 冲击测试impact test冲锻法；锤锻法；模锻法drop forging 复合刀架；复式滑座compound slide 复合色tertiary colour复合齿轮系compound gear train复振器；触发器；正反器flip-flop调校螺母；调校螺帽adjusting nut调校螺丝adjusting screw调速器governor调节regulating调校adjustment调谐电路tuning circuit质量mass质感；质地；肌理texture趟门sliding door踏靴hold down foot轮廓线；外形线outline遮光物shade锌zinc锌焊料；铜焊料spelter solder锌铸zinc casting销pin销钉接合；木钉榫dowelled joint铝aluminium锐磨sharpening锉file锉削filing锉刨surform锉刨刨刀surform blade锋利工具edge tool靠板；导板fence齿条；天梯牙gear rack齿条和齿轮rack and pinion齿榫box pin joint齿轮gear齿轮比gear ratio齿轮组；齿轮系gear train齿轮轴gear shaft齿轮传动gear drive齿轮箱gear box十六画导孔pilot hole。