18650锂电池组技术规格书

合集下载

朔明商标 ICR18650 锂二极电池规格表说明书

朔明商标 ICR18650 锂二极电池规格表说明书

Library Sort Product Specifications VER IILibrary Name Cylindrical Li‐ion Rechargeable Battery Date 2004/4/30Cylindrical Li-ion batterySpecificationType: ICR18650Prepared/Date Auditing/Date Approved/Date Genxiao Li Peng kun Gao Dragon LvLibrary Sort Product Specifications VER II Library Name Cylindrical Li‐ion Rechargeable Battery Date 2004/4/301.PerformanceTest item Test conditions Requirements(1)Outside Appearance Visual check No abnormal stain,Deformation nor damage(2) Standard test conditions Measurements are carried out at 20±5℃and relative humidity of 65±20% without other specified condition.Accuracy of voltmeters and ammeters used in test is equal to or better than the grade 0.5.(3) Standard charge Battery is charged continuously at the constant current of 0.5 I t end at voltage of 4.2V, then charge at the constant voltage of 4.2V until the end current of 20mA after Pre-discharge at the constant current of 0.2 I t until the end voltage of 2.75V/cell(4) Fast charge Charge shall be conducted continuously at theconstant current of 1500mA until the end voltage of4.2V, then charge at the constant voltage of 4.2Vuntil the end current of 20mA after Pre-dischargementioned in Item (2).(5)Open-circuitvoltage (OCV)≥3.75V(6)Rated Capacity Discharge duration of the charged battery specifiedin Item (3) shall be measured at 0.2 I t mA until theend voltage of 2.75V/cell, after rest for 0.25 hour.If the discharge duration does not reach thespecified value, the test may be repeated up to threetimes in total.Rated capacity:≥100%C5mAh(7)Capacity high-rate discharge Discharge duration of the charged battery specifiedin Item (3) shall be measured at 1500mA until the endvoltage of 2.75V/cell, after rest for 0.25 hour. Ifthe discharge duration does not reach the specifiedvalue, the test may be repeated up to three times intotal.Discharge capacity:≥90%C5mAh(8) Cycle Life (20℃) Carry out cycles (1500mA CC/CV(4.2V), discharge atthe constant current of 1500mA after rest for 0.25hour) at20± 2℃. The test end until the dischargecapacity <60%C5mAh≥300 cyclesLibrary Sort Product Specifications VER II Library Name Cylindrical Li‐ion Rechargeable Battery Date 2004/4/30(9)Low temperature discharge 1)charge shall be conducted at Item (3);2)Thebattery shall be stored under -20℃±2℃ for 16h~24h;3)Discharge shall be conducted at the constantcurrent of 0.2I t mA until the end voltage of2.75V/cell;Discharge capacity:≥60%C5mAh2 Mechanical testTest Item Test Conditions Requirements(1)Vibration Test Vibrate test sample for 90minutes each at roomtemperature after rated charge.Amplitude: 0.38mm(10-30Hz);0.19mm(30-55Hz)Frequency: 10-55Hz(1oct/min)Direction: X, YThen measure resistance, voltage of battery andcheck outside appearance.No rupture, fire, smoke,Nor critical damage≧90% C5mAh(2) Drop Test Drop 100% charged test sample from 1m above ontoconcrete board with more than 5cm thickness two timeseach for every direction at room temperature.Then measure rated capacity and checks outsideappearance. No rupture, fire, smoke, Nor critical damage≧90% C5mAh3 Safety evaluationTest Item Test Conditions Requirements(1) Hot Oven Test The charged battery is to be heated in a gravityconvection or circulating air oven. The temperatureof the oven is to be raised at a rate of 5±2℃ perminute. The oven is to remain for 30 minutes at 150±2℃ before the test is discontinued.No fire, Nor explosion(2)Short Circuit Test After fast charge at 20±2℃, Connect batteryterminals with electric wire ( electric resistance:50mΩor less ). And stop the test when thetemperature of battery is 10℃lower than peaktemperature.No fire, Nor explosion(3) Overcharge Test After discharged at 1 I t mA and end at 2.75V, thebattery shall be charged at 3 I t mA current with avoltage limit of 4.6V.No fire, Nor explosion(4)Dip test The charged battery shall be dipped in water for 24hin an ambient temperature of 20℃±5℃.No fire, Nor explosionLibrary Sort Product Specifications VER IILibrary Name Cylindrical Li‐ion Rechargeable Battery Date 2004/4/304 Charge State of Battery before shipmentTo be determined.(Recommendation Approx. 3.75 – 3.85V 30% charge)5 Duration of guarantee the productWe can keep on the quality in six month.6 Handling precautions on Lithium Ion Rechargeable BatteryTo assure product safety, describe the following precautions in the instruction manual of the equipment.! Danger-When charging the battery, use dedicated chargers and follow the specified conditions.-Use the battery only in the specified equipment.-Do not connect battery directly to an electric outlet or cigarette lighter charger.-Do not heat or throw battery into a fire.-Do not use, leave battery close to fire or inside of a car where temperature may be above 60℃. Also do not charge / discharge in such conditions.-Do not immerse, throw, and wet battery in water/ seawater.-Do not put batteries in your pockets or a bag together with metal objects such as necklaces.Hairpins, coins, or screws. Do not store batteries with such objects.-Do not short circuit the (+) and (-) terminals with other metals.-Do not place battery in a device with the (+) and (-) in the wrong way around.-Do not pierce battery with a sharp object such as a needle.-Do not hit with a hammer, step on or throw or drop to cause strong shock.-Do not disassemble or modify the battery.-Do not solder a battery directly.-Do not use a battery with serious scar or deformation.! Warning-Do not put battery into a microware oven, dryer, or high-pressure container.-Do not use battery with dry cells and other primary batteries, or batteries of a different package, type, or brand.-Stop charging the battery if charging is not completed within the specified time.-Stop using the battery if abnormal heat, odor, discoloration, deformation or abnormal condition is detectedDuring use, charge, or storage.-Keep away from fire immediately when leakage or foul odor is detected.-If liquid leaks onto your skin or clothes, wash well with fresh water immediately.If liquid leaking from the battery gets into your eyes, do not rub your eyes. Wash them well with clean water and go to see a doctor immediately.! Caution-Store batteries out of reach of children so that they are not accidentally swallowed.Library Sort Product Specifications VER IILibrary Name Cylindrical Li‐ion Rechargeable Battery Date 2004/4/30-If younger children use the battery, their guardians should explain the proper handling. -Before using the battery, be sure to read the user’s manual and cautions on handling thoroughly.-Thoroughly read the user’s manual for the charger before charging the battery.-For information on installing and removing from equipment, thoroughly read the user’s manual for the specific equipment.-Batteries have life cycles. If the time that the battery powers equipment becomes much shorter than usual, the battery life is at an end. Replace the battery with a new same one.-Remove a battery whose life cycle has expired from equipment immediately.-When the battery is thrown away, be sure it is non-conducting by applying vinyl tape to the (+) and (-) terminals.-When not using battery for an extended period, remove it from the equipment and store ina place with low humidity and low temperature.-While the battery pack is charged, used and stored, keep it away from objects or materials with static electric charges.-If the terminals of the battery become dirty, wipe with a dry clothe before using the battery. -The battery can be used within the following temperature ranges. Do not exceed these ranges.Charge temperature range : 0℃ to 45℃Discharge temperature range : -20℃ to 60℃(When using equipment)。

18650电池规格书

18650电池规格书

LGCRP/BTC Ryu, Duk HyunLRB-PS-CY2402003-07-16 0ApprovedDescriptionLGCRP/BTC Kim, Soo Ryoung Lithium Ion ICR18650 A3P R O D U C T S P E C I F I C A T I O NRechargeable Lithium Ion Battery Model : ICR18650 A3 2400mAhREVISIONDATE ORIGINATOR REASON FOR CHANGE 0 2004-07-16Ryu, Duk HyunOriginal ReleasePrepared Reviewed Approved Ryu, Duk HyunJung, Jae HanKim, Soo RyoungDate :’04. 07. 16. Date : ’03. 07. 16.Date : ’04. 07. 16.20 YOIDO-DONG YOUNGDUNGPO-GU,SEOUL 150-721, KOREATEL : (82) 2-3773-3599, 3659 FAX : (82) 2-3773-7005LGCRP/BTC Ryu, Duk Hyun LRB-PS-CY240 2003-07-16 0Approved DescriptionLGCRP/BTC Kim, Soo Ryoung Lithium Ion ICR18650 A31. ScopeThis product specification defines the requirements of the rechargeable lithium ion battery to be supplied to the customer by LG Chem, Ltd. Should there be any additional information required by the customer, customers are advised to contact LG Chem, Ltd. before selecting a solution.2. Description and Model2.1 Description : Rechargeable Lithium Ion Battery2.2 Model : ICR18650 A33. Technical Information3.1 Capacity Nominal : 2430 mAh (by standard charge and discharge)Minimum : 2380 mAh3.2 Nominal V oltage : Average 3.7 V3.3 Standard Charge : Constant Current and Constant V oltage (CC/CV)mACurrent =1200V oltage = 4.2 VEnd Current = 50 mA3.4 Max. Charge Current : 2400 mA3.5 Standard Discharge : Constant Current (CC)Current = 480 mAEnd V oltage = 3.0 V3.6 Max. Discharge Current : 4800 mA (for continuous discharge)3.7 Weight : Approx. 46.1 g3.8 Operating Temperature Charge :0 to 45 o CDischarge : -20 to 60 o C3.9 Storage Temperature 1 month : -20 to 60 o C3 months : -20 to 45 o C1 year : -20 to 20 o CLGCRP/BTC Ryu, Duk Hyun LRB-PS-CY240 2003-07-16 0Approved DescriptionLGCRP/BTC Kim, Soo Ryoung Lithium Ion ICR18650 A34. Cell DimensionsDiameter : 18.3 ± 0.1 mm ( Max. 18.4 mm )Height : 64.9 ± 0.2 mm ( Max. 65.1 mm )5. AppearancesThere shall be no such defects as deep scratch, crack, rust, discoloration or leakage, which may adversely affect the commercial value of the cell.6. Characteristics6.1 Standard ChargeUnless otherwise specified, “Standard Charge” shall consist of charging at constant current of 1200mA. The cell shall then be charged at constant voltage of 4.2V while tapering the charge current. Charging shall be terminated when the charging current has tapered to 50mA. For test purposes, charging shall be performed at 23ºC ± 2ºC.6.2 Standard Discharge“Standard Discharge” shall consist of discharging at a constant current of 480mA to 3.0V.Discharging is to be performed at 23 ºC ± 2 ºC unless otherwise noted (such as capacity versus temperature).6.3 Initial CapacityCells shall be charged per 6.1 and discharged per 6.2 within 1 hour after full charge. Initial capacity shall meet the following requirement.Initial Capacity ≥ 2380 mAh6.4 Cycle LifeCells shall be charged at constant current of 1200mA to 4.2V with end current of 50mA. Cells shall be discharged at constant current of 1200mA to 3.0V. Cells are to rest 10 minutes after charge and20 minutes after discharge. A cycle is defined as one charge and one discharge. Discharge capacityshall be measured per 6.1 and 6.2 after 300 cycles.Discharge capacity (301th Cycle) ≥80 % (of minimum capacity in 3.1)6.5 Initial AC ImpedanceLGCRP/BTC Ryu, Duk Hyun LRB-PS-CY240 2003-07-16 0Approved DescriptionLGCRP/BTC Kim, Soo Ryoung Lithium Ion ICR18650 A3Initial AC impedance is measured at 1kHz after standard charge.Initial AC Impedance ≤ 90 mΩ (with PTC)6.6 Temperature Dependency of CapacityCells shall be charged per 6.1 at 23ºC ± 2ºC and discharged per 6.2 at the following temperatures.Relative capacity at each temperature shall meet the following.Charge Temp. Discharge Temperature-10ºC0ºC 23ºC 60ºC23ºC70 % 90 % 100 % 95 %6.7 Storage CharacteristicsCells shall be charged per 6.1 and stored in a temperature-controlled environment at 23ºC ± 2ºC for30 days. After storage, cells shall be discharged per 6.2 to obtain the remaining capacity.Remaining capacity ≥90 % (of minimum capacity in 3.1)6.8 Cell V oltage (as of shipment)V oltage range : 3.7 ~ 3.9 V7. Mechanical Characteristics7.1 Drop TestTest method : Cells charged per 6.1 are dropped onto an wooden floor from 4 feet height for 3 cycles, where each cycle consists of 3 drops, 2 drops from each cell terminal and1drop from the side of cell can (Total number of drops = 9). After test, cells aredischarged per 6.2 and cycled per 6.1 and 6.2 for 3 cycles to obtain recoveredcapacity.Criteria : No leakage, Capacity recovery rate ≥ 80 %7.2 Vibration TestTest method : Cells charged per 6.1 are vibrated for 90 minutes per each of the three mutually perpendicular axis (x, y, z) with an amplitude of 0.8mm, frequency of 10Hz to55Hz and sweep of 1Hz change per minute. After test, cells are discharged per6.2 and cycled per 6.1 and 6.2 for 3 cycles to obtain recovered capacity.Criteria : No leakage, Capacity recovery rate ≥ 80 %LGCRP/BTC Ryu, Duk Hyun LRB-PS-CY240 2003-07-16 0Approved DescriptionLGCRP/BTC Kim, Soo Ryoung Lithium Ion ICR18650 A38. Environmental Test8.1 High Temperature Storage TestTest method : Cells are charged per 6.1 and stored in a temperature-controlled environment at 60ºC for 1 week. After test, cells are discharged per 6.2 and cycled per 6.4 for 3cycles to obtain recovered capacity.Criteria : No leakage, Capacity recovery rate ≥ 80 %8.2 High Temperature and High Humidity TestTest method : Cells are charged per 6.1 and stored at 60ºC (95% RH) for 168 hours. After test, cells are discharged per 6.2 and cycled per 6.4 for 3 cycles to obtain recoveredcapacity.Criteria : No leakage, No rust, Capacity recovery rate ≥ 80 %8.3 Thermal Shock TestTest method : 65ºC (8Hrs) ← 3hrs →-20ºC (8Hrs) for 8 cycles with cells charged per 6.1.After test, cells are discharged per 6.2 and cycled per 6.4 for 3 cycles to obtainrecovered capacity.Criteria : No leakage, Capacity recovery rate ≥ 80 %9. Safety Test9.1 Abnormal Charge TestTest method : Cells are discharged per 6.2, then charged at constant current of 7200mA and constant voltage of 4.2V while tapering the charge current. Charging is continuedfor 48 hours (Per UL1642).Criteria : No rupture, No fire9.2 External Short-circuiting TestTest method : Cells are charged per 6.1, and the positive and negative terminal is connected bya 100mΩ-wire for 1 hour (Per UL1642).Criteria : No rupture, No fire9.3 Overdischarge TestTest method : Cells are discharged at constant current of 480mA to 250% of the minimum capacity (Per UL1642).Criteria : No rupture, No fireLGCRP/BTC Ryu, Duk Hyun LRB-PS-CY240 2003-07-16 0Approved DescriptionLGCRP/BTC Kim, Soo Ryoung Lithium Ion ICR18650 A39.4 Nail TestTest method : A nail (diameter : 2.5~5mm) is penetrated vertically through the center of cells charged per 6.1 and left for 6 hours.Criteria : No rupture, No fire9.5 Heating TestTest method : Cells are charged per 6.1 and heated in a circulating air oven at a rate of 5ºC per minute to 150ºC. At 150ºC, oven is to remain for 10 minutes before test isdiscontinued (Per UL1642).Criteria : No rupture, No fire9.6 Impact TestTest method : Cells charged per 6.1 are impacted with their longitudinal axis parallel to the flat surface and perpendicular to the longitudinal axis of the 15.8mm diameter bar(Per UL1642).Criteria : No rupture, No fire9.7 Crush TestTest method : Cells charged per 6.1 are crushed with their longitudinal axis parallel to the flat surface of the crushing apparatus (Per UL1642).Criteria : No rupture, No fire10. Standard Test ConditionsUnless otherwise specified, all tests stated in this Product Specification are conducted at temperature 23±2ºC and humidity 65 ± 20 %RH.11. Product LiabilityThe coverage of LG Chem, Ltd. is for the cell itself, while the customer assumes the liability of the product including the cell and its protection circuit.12. WarrantyAs long as the cell is treated in accordance with this Product Specification and/or Proper Use and Handling, LG Chem, Ltd. warrants that the cell should be free from any defect for a period of 1 year from date of manufacturing.LGCRP/BTC Ryu, Duk Hyun LRB-PS-CY240 2003-07-16 0 Approved DescriptionLGCRP/BTC Kim, Soo Ryoung Lithium Ion ICR18650 A3The warranty set forth above or described in Proper Use and Handling excludes a defect which is not related to manufacturing on the cell.13. OthersAny matter not included in this specification shall be conferred between the both parties.This document shall replace the document bearing a former revision index, and customers are kindly requested to destroy the former document in possession.LGCRP/BTC Ryu, Duk Hyun LRB-PS-CY240 2003-07-16 0 Approved DescriptionLGCRP/BTC Kim, Soo Ryoung Lithium Ion ICR18650 A3Fig 1. Dimensional Drawing of ICR18650 A3。

18650单电芯规格书

18650单电芯规格书

18650单电芯规格书BATTERY CO., LTD. DOC NO.: QR-WI-733-003-002/A REV. : APAGE: 1 of 8Specification Approval Sheet (cylinder Cell) 产品规格确认书(圆柱电池)Model/型号:ZZ18650Capacity/容量:1500mAhVoltage/电压:3.7V制定(Prepared By)审核(CheckedBy)批准(ApprovedBy)DOC NO.: QR-WI-733-003-002/A REV. : APAGE: 2 of 81.0基本特性Basic performance型号Model BJ18650P 外壳材质Can Material 镀镍钢Nickel-plated 标称容量NominalCapacity,(0.2C5A)1300mAh额定电压Nominal 3.70V 充电截止电压Max 4.20 V 放电终止电压 2.80V 最大充电电流Max.Charge Current1C5A标准持续放电流10C5A最大瞬间放电电流Max. Discharge Curent20 C5A电池最大直径(光壳)18.5电池最大高度(光壳)66mm 电池重量(Approx.) 约36g 内阻(Max, at 1000Hz.)≤16mΩ充电方法Charge 标准0.2C5A×快速 1 C5A×操作温度Operating Temperature 充电Charge0℃~45℃放电Discharge-20℃~60℃贮存Storage-10℃~45℃2.0 外形图figure2.1结构图Structure3.0 主要放电曲线Mainly capability graphBJ18650P-1300mAh 15C Discharge Cruve BJ18650P-1300mAh 1C Charge CruveBJ18650P-1300mAh 13C Cycle Life BJ18650P-1300mAh -20℃Discharge CruveDOC NO.: QR-WI-733-003-002/A REV. : APAGE: 3 of 84.0 电池性能Characteristic若没有特别说明,电池在做各项试验前,均需在86KPa~106 KPa大气压,环境温度20℃±5℃,相对湿度为45%~75%的条件下,以0.2C5A恒流放电至终止电压2.8V,并在收到产品两周内进行以下试验。

18650锂电池组技术规格书

18650锂电池组技术规格书
1
YAGEO
6
R9,R10
Resistor
SMD 5.1KΩ±5%
0603
2
YAGEO
7
R7
合金电阻
P=1W
SMD 10mΩ±5%
2512
1
YAGEO
8
R6
Resistor
SMD 51Ω±5%
0603
1
YAGEO
9
C1,C2,C3
Capacitor
SMD 0.22μF
0603
3
YAGEO
10
C5,C6
断开短路电路
内阻
RSS
主回路通态电阻
RSS≤65mΩ
消耗电流
IDD
工作时电路内部消耗
30.0μA Max
零 V 充电
OV
向0 V电池充电(电芯电压最小1.7V)
允许
4 Parts list主要元件清单
NO.
元件编号
元件名称
元件规格
封装式
数量
厂商/备注
1
U1
Batteryprotection IC
S8254AANFT-TB-G
TSSOP-16
1
SEIKO
2
Q3,Q4
Silicon MOSFET
AO4407
SO-8
2
AOS
3
R1,R2,R3
Resistor
SMD 510Ω±5%
0603
3
YAGEO
4
R4,R5,R11
Resistor
SMD 10KΩ±5%
0603
3
YAGEO
5
R8
Resistor

友创伟业 YCY Li-ion 18650 3.7V 2200mAh电池说明书

友创伟业 YCY Li-ion 18650 3.7V 2200mAh电池说明书

SpecificationSeries系列:圆柱锂离子电池Pack Type组合类型:电芯+保护板+引线Model No.型号:YCY Li-ion186503.7V2200mAhCapacity容量:2200mAhVersion版本:01Customer Approve客户确认Company Name客户名称Dept.部门Signature签名Date日期QA Dept品质R&D Dept研发Approved批准1.SCOPE使用范围This specification is applied to the reference battery in this specification and manufactured by Shenzhen YCY Technology Co.,Ltd本说明书适用于本书中所提及的深圳市友创伟业科技有限公司生产的锂电池。

12Max.Continuous Discharge Current最大连续放电电流 1.5CmA 13Operation Temperature Range操作温度Charge 充电:0~45℃60±25%R.H.Discharge 放电:-20~60℃14Storable Temperature Range储存温度1year 一年-20~25℃60±25%R.H.3months 三个月-20~40℃1week 一周-20~60℃15Weight 重量Approx 约:48.0gBattery pack 电池包16Dimension尺寸Height :64.9±0.2mm (Max.50.1mm )Battery CELL电芯Diameter :18.3±0.1mm (Max.18.4mm )3.Performance And Test Conditions3.1Standard Test Conditions 标准测试条件Test should be conducted with new batteries within one week after shipment from our factory and the batterys shall not be cycled more than five times before the test.Unless otherwise defined,test and measurement shall be done under temperature of 20±5℃and relative humidity of 45~85%.If it is judged that the test results are not affected by such conditions,the tests may be conducted at temperature 15~30℃and humidity 25~85%RH.测试必须使用出厂时间不超过一个星期的新电池,且未进行过五次以上的充放电循环。

量能科技圆柱18650锂电池-2200mAh产品规格书

量能科技圆柱18650锂电池-2200mAh产品规格书

Specification for Li-ion Rechargeable cylindrical battery圆柱锂离子电池规格书MODEL/型号: 18650-2200mAh1.0 SPECIFICATIONS基本特性2.0 CONFIGURATION外形图DiameterHeight3.0 The definitions of some nomenclatures of this specification标准中的一些术语的定义:(1)Standard Charge: Charge with current 0.5C5A to limit charge voltage 4.2V under the condition of 25℃±5℃surrounding temperature, then change to charge with constant voltage till the current less than or equal to 0.01 C5A.标准充电:在环境温度20℃±5℃的条件下,以0.5C5A充电,当电池端电压达到充电限制电压4.2V时,改为恒压充电,直到充电电流小于或等于0.01C5A后停止充电(2)Initial State: The initial appearance, open-circuit voltage and internal resistance of battery.初始状态:电池的初始外观、开路电压、交流内阻。

(3)Final State: The final appearance, open-circuit voltage and internal resistance of battery.最终状态:电池的最终外观、开路电压、交流内阻。

(4)Residual Capacity: After a specific testing program, the first discharge capacity of battery.剩余容量:电池经过特定的检测程序后的首次放电容量。

18650(3600mah)规格书(标准书)

18650(3600mah)规格书(标准书)

18650(3600mah)规格书(标准书)文件名称产品型号修改记录产品型号目录1 适用范围 (4)2 引用标准 (4)3 定义........................................ .. (4)3.1 手机用电池battery for cellular phone ..... . (4) 3.2 充电限制电压 limited charge voltage ............... .. (4)3.3 额定容量 rated capacity ........................... .. (4)3.4 标称电压 nominal voltage (4)3.5 终止电压 cut-off voltage (4)4 技术参数 (4)4.1 电芯参数表 (4)4.2 主要参数表 (5)4.3 保护板参数表 (5)5 要求 (5)5.1 测试条件 (5)5.2 测量仪表与设备要求 (6)5.3 外观 (6)5.4 充电制式 (6)5.5 20℃放电性能 (6)5.6 高温性能 (6)5.7 低温性能 (6)5.8 荷电保持能力 (6)5.9 循环寿命 (7)5.10 环境适应性 (7)5.11 安全保护性能 (7)5.12 电池完全完全充电后内阻 (8)6 运输、贮存 (8)7 安全规程及使用说明 (8)8 特殊要求 (8)9 PCB原理图,电芯基本特性及外形图 (9)10 电芯充放电曲线图11 成品电池尺寸图产品型号1 适用范围本规格书适用于可充电锂离子电池产品的定义、要求、测试方法、质量评定程序及标志、包装、运输、贮存。

用户请务必严格按照规格书中的测试或使用方法进行测试或使用,如对表中的测试项目或测试方法有异议,请与供应方协商解决2 引用标准下列标准所包含的条文,通过在本规范中引用而构成为本规范的条文。

GB/T 2828-1987 逐批检查计数抽样程序及抽样表(适用于连续批的检查)GB/T 2829-1987 周期检查计数抽样程序及抽样表(适用于生产过程稳定性的检查)GB/T 2900.11-1988 蓄电池名词术语3 定义本规范采用GB/T 2900.11 中规定的术语和下列定义。

18650锂电池组技术规格书

18650锂电池组技术规格书
R4,R5,R11
Resistor
SMD 10KΩ±5%
0603
3
YAGEO
5
R8
Resistor
SMD 1MΩ±5%
0603
1
YAGEO
6
R9,R10
Resistor
SMD 5.1KΩ±5%
0603
2
YAGEO
7
R7
合金电阻
P=1W
SMD 10mΩ±5%
2512
1
YAGEO
8
R6
Resistor
SMD 51Ω±5%
过放电解除电压(备有休眠的IC,需
VDD-VM电压差在1.3V以上才可以恢复)
3.0±0.1V
过流保护
VDET3
过电流检测电压
0.1±0.025V
VDET3
过充电流检测电压
/
IDP
过电流保护电流
8.0~11.0A
IDP
过充电流保护电流
/
tVDET3
检测延迟时间
10.0±5.0mS
保护解除条件
Cut load
全新进口索尼18650/2600MAH电芯
组合方式
三串六并
电池容量
15.6AH
电池组平均电压
11.1V
电池组输出电压范围
9V→12.6V
电池组充电电压范围
12.6V→12.8V
外形尺寸
约35*185*68mm
要求电池组输出功率
25W
电池组标准充电电流
0.2-0.5C
锂电池保护功能部分
电池组具有充放电电流.电压保护电路,短路保护
0603
1
YAGEO
  1. 1、下载文档前请自行甄别文档内容的完整性,平台不提供额外的编辑、内容补充、找答案等附加服务。
  2. 2、"仅部分预览"的文档,不可在线预览部分如存在完整性等问题,可反馈申请退款(可完整预览的文档不适用该条件!)。
  3. 3、如文档侵犯您的权益,请联系客服反馈,我们会尽快为您处理(人工客服工作时间:9:00-18:30)。
5短路保护功能:当P+与B-短路时,保护电路会在5-50uS内迅速动作,切断通路,实现短路保护。
6过流保护功能:当V-端电压达(0.15±0.015V)时,保护电路会在5-15ms内迅速动作,切断通路,实现过流保护。
7过放保护恢复电压:在常温常压下,将电池连接到水泥电阻负载放电,当电流突然变为零时,断开负载,电池立即恢复输出,此时,只需将充电电源电压调至比电池电压高0.1V即可对电池进行充电。
TSSOP-16
1
SEIKO
2
Q3,Q4
Silicon MOSFET
AO4407
SO-8
2
AOS
3
R1,R2,R3
Resistor
SMD 510Ω±5%
0603
3
YAGEO
4
R4,R5,R11
Resistor
SMD 10KΩ±5%
0603
3
YAGEO
5
R8
Resistor
SMD 1MΩ±5%
0603
0.1±0.025V
VDET3
过充电流检测电压
/
IDP
过电流保护电流
8.0~11.0A
IDP
过充电流保护电流
/
tVDET3
检测延迟时间
10.0±5.0mS
保护解除条件
Cut load
断开负载
保护板最大持续电流
≤4.5A
短路保护
保护条件
外部电路短路
TSHORT
检测延迟时间
100~600uS
保护解除条件
12.6V→12.8V
外形尺寸
Байду номын сангаас约35*185*68mm
要求电池组输出功率
25W
电池组标准充电电流
0.2-0.5C
锂电池保护功能部分
电池组具有充放电电流.电压保护电路,短路保护
二、电气特性
项目
符号
详细内容
标准
过充保护
VDET1
过充电检测电压(保护电压)
4.25±0.05V
过充电检测延迟时间
1.0±0.5S
2、将锂电池与保护板按接线图连接,当电池电压处于过充电压与过放电压之间,并对P+,B-充电1秒钟后,P+与B-的输出电压为电池电压。
3电池过充保护功能:在P+与B-之间加上充电器,对电池充电,电池电压充到过充检测电压时,保护电路动作,切断充电通路,实现过充保护。
4电池过放保护功能:在P+与B-之间接上负载让电池放电,当电池电压下降到过放电压时,保护电路动作,关断放电通路,实现过放保护。
上海艾九能源科技有限公司
电池组技术规格书
型号:AJ-11.1V/15.6AH
生产日期:2011-11-03
一、电池主要参数:(具体可根据客户要求设计)
电池型号
全新进口索尼18650/2600MAH电芯
组合方式
三串六并
电池容量
15.6AH
电池组平均电压
11.1V
电池组输出电压范围
9V→12.6V
电池组充电电压范围
断开短路电路
内阻
RSS
主回路通态电阻
RSS≤65mΩ
消耗电流
IDD
工作时电路内部消耗
30.0μA Max
零 V 充电
OV
向0 V电池充电(电芯电压最小1.7V)
允许
4 Parts list主要元件清单
NO.
元件编号
元件名称
元件规格
封装式
数量
厂商/备注
1
U1
Batteryprotection IC
S8254AANFT-TB-G
1
YAGEO
6
R9,R10
Resistor
SMD 5.1KΩ±5%
0603
2
YAGEO
7
R7
合金电阻
P=1W
SMD 10mΩ±5%
2512
1
YAGEO
8
R6
Resistor
SMD 51Ω±5%
0603
1
YAGEO
9
C1,C2,C3
Capacitor
SMD 0.22μF
0603
3
YAGEO
10
C5,C6
VREL1
过充电解除电压
4.15±0.05V
最大充电电流
≤4.5A
过放保护
过放电检测电压(保护电压)
2.5±0.08V
tVDET2
过放电检测延迟时间
100±50mS
VREL2
过放电解除电压(备有休眠的IC,需
VDD-VM电压差在1.3V以上才可以恢复)
3.0±0.1V
过流保护
VDET3
过电流检测电压
Capacitor
SMD 0.1μF
0603
2
YAGEO
11
C4
Capacitor
SMD 2.2μF
0603
1
YAGEO
12
PCB
Print Circuit Board
I-2040
52*16*1.2mm
1
九和咏
5 、线路板原理图
6、顶层线路板元件位置图
六、功能与说明
1、电池组的输出为两根线(红“+”黑“—”)。
相关文档
最新文档