工厂英文缩写大全
工厂常用英文缩写
工廠常用英文縮寫PE:Products Engineer;生产工程Process engineer 制程工程TE:Test Engineer 测试工程ME:Manufacturing Engineer;制造工程;Mechanical Engineer 机械工程IE:Industrial Engineer 工业工程DCC:Document Control Center 文管中心BOM:Bill OF Material 材料清单ECN:Engineering Change Notice 工程变动公告TECN:Temporary Engineering Change Notice 工程临时变动公告ATY:Assembly Test Yield Total Yield 直通率TPM:Total Productivity MaintenancePM:Product Manager; Project Manager ECR:Engineering Change Request 工程变更申请ECO:Engineering Change Order 工程变更指令EN:Engineering Notice 工程通报WPS:Work Procedure Sheet 工作说明书ICT:In Circuit Test 电路测试P/R:pilot run;C/R control run T/R trial run 试做EVT:Engineer Verification Test 工程验证测试DVT:Design Verification Test 设计验证测试MVT:Mass Verification Test 多项验证测试ORT:On Going Reliability Test 出货信赖性测试S/W:software 软件H/W:hardware 硬件DCN:Design Change Notice 设计变更通知PVT:Production Verification Test 生产验证测试MTF:Modulation Transfer Function 调整转换功能CAT:Carriage Alignment Tool 载器调整具ID:Industrial Design 工业设计(外观设计) PCBA:Printed Circuit Board Assembly 电路板组装F/T:Function Test 功能测试CCD:Charge Coupled Device 扫描仪之读器ERS:External Reference Spec 外部规格PMP:Production Management Plan 工程管理计划SOP:Standar Operation Procedure 作业标准书QRA:Quality reliability Assurance 品保部ESD:Electrical Static Discharge 静电释放或静电防护OAY:Output Accept Yeild 直通率VMI:Visual mechanical inspection 外观检查PK:Packing 包装FQA:Final quality assurance 质量追踪CE:Component engineer 材料工程师EE:Electronic engineer 电子工程师EVT:Engineer verification test 工程验证测试WIP:Working in process inventory 在制品QA Quality Assurance 质量保证QRA :Quality & Reliability Assurance质量与可靠性保证MQA :Manufacturing Quality Assurance 制造质量保证DQA:Design Quality Assurance 设计质量保证QC:Quality Control 质量控制IQC:VQC:Vendor Quality Control 售货质量控制IPQC:In Process Quality Control 制程质量控制OQA:Out going Quality Control 出货质量控制QE:Quality Engineer 质量工程AQL:Acceptable Quality Level 可接受的质量水平DPPM:Defective Pieces Per Million units 百万件中有损件数PPM:Pieces Per Million 百万分之一CS:Custom Service 顾客服务MRB:Marerial Review Board 材料审核委员会DMR Defective Material Report 材料缺陷报告RMA:Return Marerial Administration 材料回收处理Life Test 寿命测试T/C:Temperature Cycle 温度循环H/T:High Temperature Test 高温测试L/T:Low Temperature Test 低温测试ISO:International Standard Organization 国际标准化组织SPC:Statistic process control 统计过程控制5S:Seiri Seito Seiso Seiketsu Shitsuke整理.整顿.清理.清扫.素养VMI:Visual Mechanical Inspection 外观机构检验MIL-STD:Military Standard 美军标准SPEC:Specification 规格AVL:Approval Vendor List 合格厂商QVL:Qualified Vendor List 合格厂商FQC:Final Quality Control 最终质量控制Open Box Audit 成品检验EAR:Engineering Analysis Request 工程分析需求FAI:First Article Inspection 首件检验VQM:Vendor Quality Management 厂商质量管理CAR:Corrective Action Request 改进对策要求4M:Man; Machine; Material; Method人,机,材,方法5M:Man; Machine; Material; Method; Measurement人,机,材,方法,测量MTBF:Mean Time Between Failure 平均寿命TTL:TotalFIN Finance&Accounting 财务与账目P&L:Profit & LosePerformance Variance 现象差异3 Element of Cost = M,L,OM:Material 材料L:Labor 人力O:Overhead 管理费用Fix OH Fix Overhead 固定管理费用Var OH Variable Overhead 不定管理费用COGS Cost Of Goods Sold 工厂制造成本AR:Account Receivable 应收AP:Account Payable 应支MIS Management Information System 资迅管理系统IS:Information System 资迅系统IT:Information Technology 系统技术Material Requisition Plan 材料需求计划I2:Information Integration System 资迅整合系统SAP:System Application Programming 系统申请项目ERP:Enterprise Resource Programming 企业资源项目HR Human Resource 人力资源PR:Public relation 公共关系T/O:Turn Over Rate=Monthly T/O Total People*12 GR:General Affair 总务Organization 组织HQ Head Quarter 总公司Chairmen 主席President 总裁Executive Vice President 常务副总裁Vice President 副总裁HR Human Resource 人力资源部FIN Finance 财务Sales 销售R&D:Research & Developing 研发部QA:质量保证QA DQA CSMIS:Management Information System 资迅管理系统PUR 采购PurchasingIMD:Image Management Division 影像管理事业部ITS:Information Technology System 计算机部QRA:Quality Reliability Assurance 品保部MFG:Manufacturing 制造部PMC:Production & Material Control 生(产)物(料)管(理) Materials 材料PC:Production Control 生产控制MPS:Mass Production Schedule 量产计划FGI:Finished goods Inventory 成品存货UTS:Units To Stock 存货单元WIP:Working In Process Inventory 在制品C/T:Cycle Time 循环时间,瓶颈WD:Working Days 工作天MTD:Month To Days 月初到今日(例如总表整理) YTD:Year To Days年初到今日SO:Sales Order 销售清单MO:Manufacture Order 制造清单BTO:Build To Order 订单生产P/N:Part Number 料号MC:Material Control 材料控制MRP:Material Requisition Plan 材料需求计划INV:Inventory 存货清单Inv Turn Over Days=INVS/NSB X WD 库存周转天数PSI:Production Shipping Inventory 预备待出货JIT:Just In Time 实时Safety Inventory 安全存量CKD:Completed Kits Delivery 全件组装出货SKD:Semi Kits Delivery 半件(小件)组装出货W/H:Warehouse 仓库Rec:Receiving Center 接收中心Raw MTL 原物料F/G:finish goods 成品Import/Export 进出口SI:Shipping Instruction 发货指令PL:Packing List 包装清单Inv:Shipping Invoice 出货发票ETA:Estimate Arrive 预估到达时间ETD:Estimate departure 预估离开时间BL:Bill of Landing 提货单(海运) AWB:Air Way Bill 提货单(空运)MAWB:Master Air Way Bill 主提货单HAWB:House Air Way Bill 副提货单TEU:Twenty foot Equipment Unit(Contain)二十英尺货柜FEU:Forty foot Equipment Unit(Contain)四十英尺货柜CY:Container Yard 货柜场THC:Terminal Handing Charge 码头费ORC:Original Receiving Charge 码头费PUR:Purchasing 采购FOB:Free on Board 货运至甲板(离岸价)CIF:Cost Insurance Freight 成本+运费+保险OA:Open Account 开户TT:Telegram Transfer 电汇COD:Cash On DeliveryCRP:Cost Reduction Program 降低成本方案PR:Purchasing Requisition 采购申请PO:Purchasing Order 采购单MFG Manufacturing Production 制造生产DL:Director Labor 直接人工IDL:Indirect Labor 间接人工DLH:Direct Labor Hours 直接工时Productivity=UTS/DLHPPH:Pieces Per Hour 每小时件数Efficiency=Actual/Target(%)DT:Machine Down Time 停机时间AI:Auto Insertion 自动插入MI:Manual Insertion 人工插入SMD:Surface Mount Device 表面粘着零件SMT:Surface mount technology 表面粘着技术B/I:Burn In(for how many hours at how many degree)烧机WI:Work Instruction 工作说明SOP:Standard Operation Procedure 作业指导书R/I:Run In 运转机器ESD:Electrical Static Discharge 静电释放MP:Mass Production 量产。
工厂英文缩写大全
• QA: Quality Assurance 品质保证品质保证QC: Quality Control 品质控制品质控制QE: Quality Engineering 品质工程品质工程QFD: Quality Function Design 品质机能展开品质机能展开 Quality 质量质量Quality manual 品质手册品质手册Quality policy 品质政策品质政策Range 全距全距Record 记录记录Reflow 回流回流Reject 拒收拒收Repair 返修返修Repeatability 再现性再现性Reproducibility 再生性再生性Requirement 要求要求 Residual 误差误差Response 响应响应Responsibilities 职责职责Review 评审评审Rework 返工返工Rolled yield 直通率直通率sample 抽样,样本样本Scrap 报废报废SOP: Standard Operation Procedure 标准作业书标准作业书SPC: Statistical Process Control 统计制程管制统计制程管制Specification 规格规格 SQA: Source(Supplier) Quality Assurance 供应商品质保证供应商品质保证 Taguchi-method 田口方法田口方法TQC: Total Quality Control 全面品质控制全面品质控制TQM: Total Quality Management 全面品质管理全面品质管理Traceability 追溯追溯 UCL: Upper Control Limit 管制上限管制上限USL: Upper Size Limit 规格上限规格上限V alidation 确认确认V ariable 计量值计量值V erification 验证验证V ersion 版本版本QCC Quality Control Circle 品质圈/QC 小组小组PDCA Plan Do Check Action 计划计划 执行执行 检查检查 总结总结Consumer electronics 消费性电子产品消费性电子产品Communication 通讯类产品通讯类产品Core value （核心价值）（核心价值） Love 爱心爱心Confidence 信心信心Decision 决心决心 Corporate culture (公司文化)Integration 融合融合Responsibility 责任责任Progress 进步进步QC quality control 品质管理人员品质管理人员FQC final quality control 终点品质管制人员终点品质管制人员IPQC in process quality control 制程中的品质管制人员制程中的品质管制人员OQC output quality control 最终出货品质管制人员最终出货品质管制人员IQC incoming quality control 进料品质管制人员进料品质管制人员TQC total quality control 全面质量管理全面质量管理POC passage quality control 段检人员段检人员 QA quality assurance 质量保证人员质量保证人员OQA output quality assurance 出货质量保证人员出货质量保证人员QE quality engineering 品质工程人员品质工程人员FAI first article inspection 新品首件检查新品首件检查FAA FAA first article assurance first article assurance 首件确认首件确认CP capability index 能力指数能力指数SSQA standardized supplier quality audit 合格供应商品质评估合格供应商品质评估 FMEA failure model effectiveness analysis 失效模式分析失效模式分析AQL Acceptable Quality Level 运作类允收品质水准运作类允收品质水准S/S Sample size 抽样检验样本大小抽样检验样本大小ACC Accept 允收允收REE Reject 拒收拒收CR Critical 极严重的极严重的MAJ Major 主要的主要的MIN Minor 轻微的轻微的Q/R/S Quality/Reliability/Service 品质/可靠度/服务服务 P/N Part Number 料号料号L/N Lot Number 批号批号AOD Accept On Deviation 特采特采UAI Use As It 特采特采FPIR First Piece Inspection Report 首件检查报告首件检查报告PPM Percent Per Million 百万分之一百万分之一SPC Statistical Process Control 统计制程管制统计制程管制SQC Statistical Quality Control 统计品质管制统计品质管制GRR Gauge Reproducibility & Repeatability 量具之再制性及重测性判断量可靠与否量具之再制性及重测性判断量可靠与否 DIM Dimension 尺寸尺寸DIA Diameter 直径直径 QIT Quality Improvement Team 品质改善小组品质改善小组ZD Zero Defect 零缺点零缺点QI Quality Improvement 品质改善品质改善QP Quality Policy 目标方针目标方针TQM Total Quality Management 全面品质管理全面品质管理RMA Return Material Audit 退料认可退料认可 7QCTools 7 Quality Control Tools 品管七大手法品管七大手法通用之件类通用之件类ECN Engineering Change Notice 工程变更通知(供应商)ECO Engineering Change Order 工程改动要求(客户)PCN Process Change Notice 工序改动通知工序改动通知PMP Product Management Plan 生产管制计划生产管制计划SIP Standard Inspection Procedure 制程检验标准程序制程检验标准程序SOP Standard Operation Procedure 制造作业规范制造作业规范IS Inspection Specification 成品检验规范成品检验规范BOM Bill Of Material 物料清单物料清单PS Package Specification 包装规范包装规范 SPEC Specification 规格规格DWG Drawing 图面图面系统文件类系统文件类ES Engineering Standard 工程标准工程标准IWS International Workman Standard 工艺标准工艺标准ISO International Standardization Organization 国际标准化组织国际标准化组织 GS General Specification 一般规格一般规格部类部类PMC Production & Material Control 生产和物料控制生产和物料控制PCC Product control center 生产管制中心生产管制中心PPC Production Plan Control 生产计划控制生产计划控制MC Material Control 物料控制物料控制DCC Document Control Center 资料控制中心资料控制中心QE Quality Engineering 品质工程(部)QA Quality Assurance 品质保证处品质保证处QC Quality Control 品质管制(课) PD Product Department 生产部生产部LAB Laboratory 实验室实验室IE Industrial Engineering 工业工程工业工程R&D Research & Design 设计开发部设计开发部• QC: Quality Control 品質管控品質管控• QA: Quality Assurancel 品質保證品質保證• IQC: Incoming Quality Control 進料品質管制進料品質管制• IPQC: In-Process Qualityl Control 制程品質管制制程品質管制• FQC: Final Quality Control 最終品質管制最終品質管制• OQC: Outgoing Qualityl Control 出貨品質管制出貨品質管制• QCC: Quality Control Circle 品管圈l• QE: Qualityl Engineering 品質工程品質工程• PDCA 管理循環(Plan-Do-Check-Action)l• SPC : Statisticl Process Control 統計制程管制統計制程管制• TQM: Total Quality management 全面品質管制l• WIP: Workl In Process 在制品在制品• MO: Manufacture Order 制令制令• JIT: Just In Time 即時管理即時管理• ISO: International Organization For Standardization 國際標準化組織l• BOM: Bill Of Material 物料清單物料清單• 5S : 整理,整頓,清掃,清潔,素養l• FIFO: FIRST IN FIRST OUT先進先出管理先進先出管理。
工厂企业常用英文缩写
進料檢 驗
國際標 準組織
資訊部
品Hale Waihona Puke 工 程師 批退率目標管 理
物控 設備維 護工程 師
ECO ECR ENG ERP ESD EVT FAI FIN
Engine ering Change Order (ECO) Engine ering Change Reques t(ECR) Engine ering depart ment Enterp rise Resour ce Plan Electro Static Discha rge(ES D) Engine ering Verific ation Test(E VT) First Article Inspect ion (FAI) Financ e depart ment
在製品 (半成 品)
特采
零缺點
制程/產 品工程
Produc
tion
PMC
&Mate rial
Contro
l(PMC)
Process
PMP
Manag ement
Plan Produc
PPH
tion Per
Hour Parts
PPM
Per Million
(PPM)
Purcha
sing
PUR depart
Verific
DVT ation
Test(D
VT)
Engine
ering
ECN Change
Notice(
ECN)
出貨單 設計變 更通知
百万分 不良率
免驗
設計鑑 定測試
工程變 更通知
p
mQuenatlity
QE Engine
100个工厂常用英文缩写
设计验证
19 ECN Engineering Change Notice 工程变更通知
20 ECO Engineering Change Order
工程变更指令
21 ECR Engineering Change Request 工程变更需求
22
EE Electronic Engineering
电子工程
欧规手持装置数字地面广播标准
16
DVB-S
Digital Video BroadcastingSatellite
17
DVB-T
Digital Video BroadcastingTerrestrial
欧规数字电视卫星广播标准 欧规数字电视地面广播标准
18 DVT Design Verification Testing
面向产品生命周期各/某环节的设计。 DFP：Design for Procurement 可采购设计 DFM：Design for Manufacture 可生产设计 DFT：Design for Test 可测试设计 DFD：Design for Diagnosibility 可诊断分析设计 DFA：Design for Assembly 可组装设计 DFE：Design for Environment 可环保设计 DFF：Design for Fabrication of the PCB 为PCB可 制造而设计 DFS：Design for Serviceability 可服务设计 DFR：Design for Reliability 为可靠性而设计 DFC：Design for Cost 为成本而设计
关键绩效指标
45
KR Korea
韩国
46 MAJ Major
工厂部门英文缩写
工厂各部门英文缩写工程Engineer Department品保Quality Control Department制造 Production Department技术办公室Technical Office研发 Research & Development样品组 Sample Room设备课 Equipment Dept.组装课 Assembling Dept.仓库Warehouse营业部 Business Office人力资源部 Human Resources Department总务部 General Affairs Department财务部 General Accounting Department销售部 Sales Department促销部 Sales Promotion Department国际部 International Department出口部 Export Department进口部 Import Department公共关系 Public Relations Department广告部 Advertising Department企划部 Planning Department产品开发部 Product Development Department研发部 Research and Development Department(R&D) 秘书室 Secretarial Pool采购部 Purchasing Department工程部 Engineering Department行政部 Admin. Department人力资源部 HR Department市场部 Marketing Department技术部 Technolog Department客服部 Service Department行政部 Administration财务部 Financial Department董事长室 The Chairman's room总经理室 Direcotor, or President副总经理室 Deputy Director, or Vice president 总经办 General Deparment采购部 Purchase & Order Department工程部 Engineering Deparment研发部 Research Deparment生产部 Productive Department销售部 Sales Deparment业务部 Branch Deparment事业部 Department拓展部 Business Expending Department物供部 Supply DepartmentB＆D business and development 业务拓展部Marketing 市场部Sales 销售部HR 人力资源部Account 会计部PR people relationship 公共关系部OFC (Office, 但不常见) / OMB = Office of Management and Budget 办公室Finance 财务部MKTG (Marketing) 市场部R&D (Research & Development) 研发部MFG (Manufacturing) 产品部Administration Dept. 管理部Purchasing Dept 采购部Chairman/President Office // Gerneral Manager office or GM office 总经理办公室Monitor & Support Department 监事会Strategy Research 战略研究部外销部:Overseas Department,International Sales Section,Export Section财务科:Financial/Fiscal Department会议室:Meeting Room/Hall/Auditorium,或Conference Hall/Auditorium或直接Auditorium, 视其大小而定了。
最全版工厂常用英文缩写简称大全
Category 類別Abbreviation簡稱Full Name全稱Paraphrase釋義體系術語CSR Corparation Social Responsibility企業社會責任體系術語EICC Electronic Industry Code of Conduct電子行業行為守則體系術語FCC Federal Communications Commission美国联邦通信委员会體系術語GP Green Parts綠色產品/環保體系術語IP intellectual property知識產權(保護)體系術語ISO International Standards Organization國際標準化組織體系術語QPA Quality Process Audit品質製程稽核體系術語QSA Quality System Audit品質體系稽核體系術語SER Social & Environmental Responsibility社会与环境责任質量類APQP Advanced Product Quality Planning先期產品質量規劃質量類AQL Acceptable Quality Level允收質量水準質量類Ca Capability of Accuracy製程準確度質量類CA Cause Analysis/Corrective Action原因分析/糾正措施質量類CAPA Corrective Action & Prevetive Action糾正預防措施質量類CAR Correction Action Report改善對策報告質量類CIP Continuous Improvement Program質量持續改善計劃質量類CLCA Closed Loop Corrective Action闭环纠正措施質量類Cp Capability of Precision製程精密度質量類CPK Process Capability index製程能力指數質量類CQ Corporation Quality公司質量質量類CTQ Critical To Quality關鍵質量特性質量類DMAIC Define=>Measure=> Analysis=>Improve=> Control Six Sigma的步驟﹕定義測量分析改善控制質量類DOE Design of Experiments實驗設計法質量類DPMO Defects Per Million Opportunities每百萬個機會的缺點數質量類DPPM Defect Parts Per Million 每百萬個單位數中的不合格單位數質量類DRI Derectly responsibility indictor直接負責人質量類FA Failure Analysis失效分析Category 類別Abbreviation簡稱Full Name全稱Paraphrase釋義質量類FAI First Article Inspection首件確認質量類FMEA Failure Mode Effect Analysis失效模式分析質量類FPY First Pass Yield直通率質量類FRR Field Return Rate市場退貨率質量類JQE Joint Quality Engineer 客户端品质工程师(SQE的眼睛和耳朵)質量類KCC Key Control Characteristics 关键控制特性=過程特殊特性質量類KPC key product characteristic 關鍵產品特性=產品特殊特性質量類LAR Lot Acceptance Rate合格率質量類LRR Lot Reject Rate批退率質量類MBO Management By Objection目標管理質量類MCD Material Composition Declaration物質成分宣告質量類MRB Material Review Board材料評審委員會質量類MSA Measurement System Analysis測量系統分析質量類NG Not Good不良質量類OBA Out of Box Audit開箱檢驗質量類ORT Ongoing Realiability Test 產品連續性測試/產品可靠性測試質量類PDCA Plan-Do-Check-Action管理循環/質量環質量類PPAP Production Parts Approval Process生產零件認可程序質量類PR/R Problem reporting and solving問題通報與解決質量類PSC Product Special CharacteristicsProcess Special Characteristics 产品特殊特性過程特殊特性質量類QBR Quarter Bussiness Review季度業務評審質量類QCC Quality Control Circle品管圈質量類QIS Quality Information System質量信息系統質量類QIT Quality Improvement Team質量改善小組質量類QQR Quarter Quality Review季度質量評審Category類別Abbreviation簡稱Full Name 全稱Paraphrase釋義質量類RMA Return Material Authoriztion 物料退貨授權質量類RPNRisk Priority Number風險係數》126質量類SMART Goal Specific MeasurableAttainableRelevant Time-based 明確的,具體的可衡量的可達到的相關性的時效性的質量類SOD Severity Occurrence Detectivity 嚴重度S>8，頻度（發生率）O ，探測度D 質量類SPC Statistical Process Control 统计过程控制質量類VLRR Verified Line Reject Rate 產線不合格品判退率質量類SIP Standard Inspection Procedure 標準檢驗程序質量類MSOP Measurement Standard Operation Procedure測量標準作業程序精益生產BPR Business Process Re-Engineering 企業流程再造精益生產BR Business Re-Engineering企業再造精益生產ECRS Eliminate-Combine-Rearrange-Simplify 取消-合併-重排-簡化精益生產GRR Gage Repeatability & Reproducibility 量具的重複性和再現性精益生產JIT Just In Time 即時管理精益生產LB Line Balance 生產線平衡精益生產LP Lean Production 精益生產精益生產MIR Method Improve Report 提案改善精益生產OEE Overall Equipment Effectiveness 設備綜合效率=時間開動率*性能開動率*良品率精益生產PPH piece person hour人均時產能精益生產SIPOC Supplier-Input-Process-Output-Customer 供應商-投入-流程-產出-顧客精益生產SMED Single Minute Exchange of Die 快速換模/單分鐘換模精益生產TPM Total Productive Maitenance 全面生產性維護精益生產VSMValue Stream Mapping價值流程圖Category 類別Abbreviation簡稱Full Name全稱Paraphrase釋義管理系統BPM Bussiness Process Management商業流程管理管理系統CRM Customer Relationship Management客戶關係管理管理系統EIS Executive Information System高階主管資訊系統管理系統ERP Enterprise Resource Planning企業資源規劃管理系統GLM Global Logistics Management全球運籌管理管理系統GPS Global Positioning System全球定位系统管理系統GSM Global System for Mobile communications全球移动通信系统管理系統MES Manufacturing Execution System製造執行系統管理系統MIS Management Information System信息管理系統管理系統PLM Production Life-cycle Management產品生命週期管理管理系統SPM Services-Oriented Process Management服務導向流程管理部門名稱AE Acoustic Engineering聲學工程部門名稱ME Machanical Engineering結構工程部門名稱EE Electronic Engineering電子工程部門名稱AM Account Manager客戶經理/業務部門名稱ASD Assembly Department組裝部門名稱Bds Boards董事會部門名稱Dept Dep ar t ment部門部門名稱DIP Dual In-line Pakage雙列直插式封裝部門名稱DQE Design Quality Engineer設計質量工程部門名稱FATP Final assembly test and pack最後組裝,測試和包裝部門名稱FQC Final Quality Control終點品質管制部門名稱HR Human Resources人力資源部門名稱IE Industrial Engineering工業工程部門名稱IQC Incoming Quality Control進料質量控制部門名稱MFG M anu f acturin g製造部門名稱OPM Operation Project Management運營項目管理Category 類別Abbreviation簡稱Full Name全稱Paraphrase釋義部門名稱OQC Outgoing Quality Control出貨質量控制部門名稱PM Project Management項目管理部門名稱PMC Product Material Control生產物料控制部門名稱PQC Process Quality Control製程質量控制部門名稱QPM Quality Project Management質量專案管理部門名稱QRA Quality & Reliability Assurance質量可靠性保證部門名稱RD Research and Development研發部門名稱SCM Supplier Chain Management供應鏈管理部門名稱SMT Surface Mount Technology表面貼裝技術部門名稱SQM Supplier Quality Management供應商質量管理規格類CMF Color Material Finishing顏色/材質/工藝規格類EMC Electro Magnetic Compatibility電磁相容規格類EMC Electro Magnetic Compatibility电磁兼容規格類EMI Electro Magnetic Interference电磁干扰規格類EMS Electro Magnetic Susceptibility电磁敏感度 (电磁抗干扰)規格類ESD Electrostatic Discharge靜電放電規格類HDD Hard Disk Drive硬盘驱动器產品類型BCP Bluetooth Charger Product藍牙充電器產品產品類型BD Bluetooth Device藍牙設備產品類型BHC Bluetooth Headset for Comm.藍牙無線產品產品類型DSH Dynamic Speaker for Headphone動圈式揚聲器產品類型DTR Dynamic Telephone Receiver動圈式收受話器產品類型ECM Electret Condenser Microphone駐極體電容式麥克風產品類型HDT HeaDseT頭戴耳機產品類型HPS High Performance Speaker高性能喇叭產品類型PBP Power Bank Product移動電源產品產品類型SBP Smart Battery Pack智能電池組Category類別Abbreviation簡稱Full Name 全稱Paraphrase釋義產品類型TWS True Wireless Stereo 無線立體聲藍牙耳機產品類型WCP Wireless Charger Product 無線充電器採購類AVL Approved Vendor List 合格供應商名錄採購類B/L Bill of lading提單採購類EOQ Economic Order Quantity 經濟採購量採購類ETAEstimated Time of Arrival 預計到達時間採購類ETC Estimate Time Completed 預估完成時間採購類FCST F ore C a ST 預估採購類MRP Material Requirement Planning 物料需求計劃採購類PO Purchasing Order 採購訂單財務類AP Accounts Payable 應付賬款財務類Inv Inv oice發票客戶名稱BOCBOSE Operation CenterBOSE 運營中心工藝類IML Insert Molding Label模內貼標表面：硬化透明薄膜中间：印刷图案层背面：注塑层工藝類LSR Lequid Silicon Rubber 液体硅橡胶工藝類MIM Metal Injection Molding金屬粉末注塑成型技術工藝類NCVM Non conductive vacuum metalization 不導電真空電鍍工藝類OSPOrganic Solderability Preservatives有机保焊膜，又称护铜剂OSP 的工艺流程Category 類別Abbreviation簡稱Full Name全稱Paraphrase釋義工廠類型JDM Joint Design Manufacture聯合設計製造工廠類型ODM Original Design Manufacturer原始设计制造商工廠類型OEM Original Equipment Manufacturer 原始设备制造商;定点生产，俗称代工（生产）人資類HC H ead c ount員工人數人資類Info Infor mation資料人資類TR Turnover Rate周轉率/離職率NPI BOM Bill Of Material物料清單NPI DFM Design For Manufacturing設計製造NPI DPR Design Producibility Review--SonyEricsson客戶新產品開發導入時:設計可生產性之檢討NPI DVT Design Verification Testing设计验证测试NPI EOL End Of Live產品壽命終止NPI EPR engineering pilot run工程試做NPI EVT Engineering Verification Test工程验证测试NPI MP MASS Product量產NPI NPD New product Development新產品設計NPI NPI New Product Introduction新產品導入NPI NRE Non-Recurring(Recur現在分詞復發/循環/再來) Engineering一次性工程/非重複性工程NPI PVT Pilot-run Verification Test小批量过程验证测试NPI RFI Request For Information信息要求NPI RFQ Request For Quotations詢價BOSE文件ASD Automotive Systems Division汽車系統部BOSE文件GSM Global Supply Management全球供應管理BOSE文件PSDS Part Submission Data Sheet零件提交数据表BOSE文件QOS Quality of ServiceQuality Overall Summary服务质量全面质量总结Category 類別Abbreviation簡稱Full Name全稱Paraphrase釋義BOSE文件SPAP Supplier Production Approval Process供應商產品批准程序BOSE文件SRC Supplier Report Card供應商評分卡BOSE文件SRD Supplier Readiness Dashboard供應商準備指示板BOSE文件STA Supplier Technology Assurance供應商技術保證通用類ASAP As soon as possible盡快通用類CVMI Consider Vendor Managed Inevntory廠商管理存貨考慮通用類DRI Derectly responsibility indictor直接負責人通用類PIC Person In Charge負責人通用類FYI For Your Information供參考通用類Intro Intro duction介紹通用類MR Manufacturing Resources制造資源通用類NA Not Applicable不適用通用類RF Referred value參考值通用類SOP Standard Operation Procedure標準作業程序通用類TBA To be assured待確定通用類TBD To be determined待確定通用類VMI Vendor Management Inventory供應商管理庫存通用類WIP Work in process在製品。
制造业工厂常用英文与缩写词汇大全
制造业工厂常用英文与缩写词汇大全在制造业工厂中，英文词汇和缩写词汇被广泛应用于各个环节和领域。
掌握这些常用词汇和缩写词汇对于工厂中的员工来说至关重要，可以提高沟通效率、减少误解，并且有助于更好地理解和应用相关专业知识。
本文将为你提供一份制造业工厂常用英文词汇和缩写词汇的大全，帮助你更好地适应工厂工作环境。
一、制造业工厂常用英文词汇1. Assembly Line：装配线2. Automation：自动化3. Conveyor Belt：传送带4. Equipment：设备5. Inventory：库存6. Maintenance：维护7. Production：生产8. Quality Control：质量控制9. Raw Materials：原材料10. Safety Regulations：安全规定11. Supply Chain：供应链12. Testing：测试13. Warehousing：仓储14. Workflow：工作流程二、制造业工厂常用英文缩写词汇1. BOM (Bill of Materials)：物料清单2. CAD (Computer-Aided Design)：计算机辅助设计3. CAM (Computer-Aided Manufacturing)：计算机辅助制造4. ERP (Enterprise Resource Planning)：企业资源计划5. ISO (International Organization for Standardization)：国际标准化组织6. JIT (Just-in-Time)：准时生产7. MES (Manufacturing Execution System)：制造执行系统8. OEE (Overall Equipment Effectiveness)：设备综合效率9. PLC (Programmable Logic Controller)：可编程逻辑控制器10. QA (Quality Assurance)：质量保证11. QC (Quality Control)：质量控制12. RFID (Radio Frequency Identification)：射频识别13. SOP (Standard Operating Procedure)：标准操作规程14. TPM (Total Productive Maintenance)：全面生产维护三、制造业工厂常用英文词汇和缩写词汇的应用场景举例1. 入职培训：In the onboarding process, new employees will receive training on equipment operation, safety regulations, and quality control.2. 生产计划：The production plan should take into account the availability of raw materials and equipment capacity.3. 装配线优化：Automation plays a crucial role in optimizing assembly line efficiency and reducing production time.4. 设备维护：Regular maintenance of machines and equipment is necessary to ensure their smooth operation.5. 质量检验：Quality control inspectors are responsible for conducting thorough testing to ensure product quality meets the specified standards.6. 供应链管理：Efficient supply chain management involves coordinating the flow of raw materials, production, and distribution.7. 库存管理：Accurate inventory management helps prevent shortages and minimize unnecessary storage costs.8. 工作流程改进：Manufacturing engineers continuously analyze and improve workflow to increase overall productivity.9. 安全意识培养：Creating a strong safety culture in the factory is vital to prevent accidents and ensure a secure working environment.以上仅为部分常用英文词汇和缩写词汇的示例，工厂中还存在更多领域的英文术语和缩写词汇。
生产制造英文缩写大全
EVT(Engineering Verification Test)工程验证测试阶段DVT(Design Verification Test)设计验证测试阶段DMT（Design Maturity Test）成熟度验证MVT（Mass-Production Verification Test）量产验证测试PVT(Production/Process Verification Test)生产/制程验证测试阶段MP(Mass Production)量产工程师类:PE: Product Engineer 产品工程师Process Engineer 制程工程师ME: Mechanical Engineer 机构工程师IE：Industrial Engineer 工业工程师QE: Quality Engineer 品质工程师SQESupplier Quality Engineer供货商质量工程师QC quality control 品质管理人员FQC final quality control 终点质量管理人员IPQC in process quality control 制程中的质量管理人员OQC output quality control 最终出货质量管理人员IQC incoming quality control 进料质量管理人员TQC total quality control 全面质量管理POC passage quality control 段检人员QA quality assurance 质量保证人员OQA output quality assurance 出货质量保证人员QE quality engineering 品质工程人员TE Test Engineer 测试工程师AE Automatic Engineer 自动化工程师研发类:R&D Research & Design 设计开发部ID (Industry Design)工业设计MD (Mechanical Design)结构设计HW(Hardware) 硬件设计SW(Software)软件设计PDM Product Data Management 产品数据管理PLM product lifecycle management 产品生命周期管理电子设计:ICT In Circuit Test 电路测试PCB Printed Circuit Board 印刷电路板PCBA Printed Circuit Board Assembly 印刷电路板装配FPC FlexiblePrintedCircui 挠性电路板EMI Electrical Magnetic Interference 电子干扰RFI adio Frequency Interference射频干扰。
- 1、下载文档前请自行甄别文档内容的完整性，平台不提供额外的编辑、内容补充、找答案等附加服务。
- 2、"仅部分预览"的文档,不可在线预览部分如存在完整性等问题,可反馈申请退款(可完整预览的文档不适用该条件!)。
- 3、如文档侵犯您的权益，请联系客服反馈,我们会尽快为您处理(人工客服工作时间：9:00-18:30)。
•QA: Quality Assurance 品质保证
•QC: Quality Control 品质控制
•QE: Quality Engineering 品质工程
•QFD: Quality Function Design 品质机能展开
•Quality 质量
•Quality manual 品质手册
•Quality policy 品质政策
•Range 全距
•Record 记录
•Reflow 回流
•Reject 拒收
•Repair 返修
•Repeatability 再现性
•Reproducibility 再生性
•Requirement 要求
•Residual 误差
•Response 响应
•Responsibilities 职责
•Review 评审
•Rework 返工
•Rolled yield 直通率
•sample 抽样,样本
•Scrap 报废
•SOP: Standard Operation Procedure 标准作业书
•SPC: Statistical Process Control 统计制程管制•Specification 规格
•SQA: Source(Supplier) Quality Assurance 供应商品质保证•Taguchi-method 田口方法
•TQC: Total Quality Control 全面品质控制
•TQM: Total Quality Management 全面品质管理•Traceability 追溯
•UCL: Upper Control Limit 管制上限
•USL: Upper Size Limit 规格上限
•Validation 确认
•Variable 计量值
•Verification 验证
•Version 版本
•QCC Quality Control Circle 品质圈/QC小组
•PDCA Plan Do Check Action 计划执行检查总结•Consumer electronics 消费性电子产品
•Communication 通讯类产品
•Core value （核心价值）
•Love 爱心
•Confidence 信心
•Decision 决心
•Corporate culture (公司文化)
•Integration 融合
•Responsibility 责任
•Progress 进步
•QC quality control 品质管理人员
•FQC final quality control 终点品质管制人员
•IPQC in process quality control 制程中的品质管制人员
•OQC output quality control 最终出货品质管制人员
•IQC incoming quality control 进料品质管制人员
•TQC total quality control 全面质量管理
•POC passage quality control 段检人员
•QA quality assurance 质量保证人员
•OQA output quality assurance 出货质量保证人员
•QE quality engineering 品质工程人员
•FAI first article inspection 新品首件检查
•FAA first article assurance 首件确认
•CP capability index 能力指数
•SSQA standardized supplier quality audit 合格供应商品质评估
•FMEA failure model effectiveness analysis 失效模式分析
•AQL Acceptable Quality Level 运作类允收品质水准
•S/S Sample size 抽样检验样本大小
•ACC Accept 允收
•REE Reject 拒收
•CR Critical 极严重的
•MAJ Major 主要的
•MIN Minor 轻微的
•Q/R/S Quality/Reliability/Service 品质/可靠度/服务
•P/N Part Number 料号
•L/N Lot Number 批号
•AOD Accept On Deviation 特采
•UAI Use As It 特采
•FPIR First Piece Inspection Report 首件检查报告
•PPM Percent Per Million 百万分之一
•SPC Statistical Process Control 统计制程管制
•SQC Statistical Quality Control 统计品质管制
•GRR Gauge Reproducibility & Repeatability 量具之再制性及重测性判断量可靠与否
•DIM Dimension 尺寸
•DIA Diameter 直径
•QIT Quality Improvement Team 品质改善小组
•ZD Zero Defect 零缺点
•QI Quality Improvement 品质改善
•QP Quality Policy 目标方针
•TQM Total Quality Management 全面品质管理
•RMA Return Material Audit 退料认可
•7QCTools 7 Quality Control Tools 品管七大手法
•通用之件类
•ECN Engineering Change Notice 工程变更通知(供应商)
•ECO Engineering Change Order 工程改动要求(客户)
•PCN Process Change Notice 工序改动通知
•PMP Product Management Plan 生产管制计划
•SIP Standard Inspection Procedure 制程检验标准程序
•SOP Standard Operation Procedure 制造作业规范
•IS Inspection Specification 成品检验规范
•BOM Bill Of Material 物料清单
•PS Package Specification 包装规范
•SPEC Specification 规格
•DWG Drawing 图面
•系统文件类
•ES Engineering Standard 工程标准
•IWS International Workman Standard 工艺标准
•ISO International Standardization Organization 国际标准化组织•GS General Specification 一般规格
•部类
•PMC Production & Material Control 生产和物料控制
•PCC Product control center 生产管制中心
•PPC Production Plan Control 生产计划控制
•MC Material Control 物料控制
•DCC Document Control Center 资料控制中心
•QE Quality Engineering 品质工程(部)
•QA Quality Assurance 品质保证处
•QC Quality Control 品质管制(课)
•PD Product Department 生产部
•LAB Laboratory 实验室
•IE Industrial Engineering 工业工程
•R&D Research & Design 设计开发部
•QC: Quality Control? 品质管控
•?QA: Quality Assurancel 品质保证
•?IQC: Incoming Quality Control 进料品质管制
•?IPQC: In-Process Qualityl Control 制程品质管制
•?FQC: Final Quality Control 最终品质管制
•?OQC: Outgoing Qualityl Control 出货品质管制
•?QCC: Quality Control Circle 品管圈l
•?QE:? Qualityl Engineering? 品质工程
•?PDCA管理循环(Plan-Do-Check-Action)l
•?SPC : Statisticl Process Control 统计制程管制
•?TQM: Total Quality management 全面品质管制l
•?WIP: Workl In Process? 在制品
•?MO: Manufacture Order 制令
•?JIT: Just In Time 即时管理
•?ISO: International Organization For Standardization 国际标准化组织l •?BOM: Bill Of Material 物料清单
•?5S : 整理,整顿,清扫,清洁,素养l
•?FIFO: FIRST IN FIRST OUT先进先出管理。