注塑方面英语术语共22页文档
注塑常用术语英文表达
1.雾气Moisture Streaks2.玻纤分配不均Glass Fiber Streaks3.困气Gas Trap Effect4.银丝纹Sliver Marks5.结合线Weld Line6.水波痕Water Wave Effect7.黑点Dark Sport8.顶出印Visible Ejector Marks9.变形Deformation During Demolding10.填充不足Short Filling11.冷料流痕Cold Slug12.进胶口点不良Dull Spots Near The Sprue13.喷射痕Jetting14.表面起层Flaking Of The Surface Layer15.浮泡Entrapped Air16.过热变色Burnt Streaks17.龟裂Stress Crack18.缩水痕Sink Marks19.真空气泡Density Bubble20.披锋Flash21.擦伤印Scratch MarksGlass fiber rich surface/glass emergence on the surface22 尺寸过大Over dimension23 尺寸过小Under dimension24 翘曲Warpage/warped25 收缩Shrinkage/shrink26 缩影Sink marks27 打不满Short shot/short molding塑料模具mould of plastics注塑模具injection mould冲压模具die模架 mould base定模座板 Top clamping plateTop plateFixed clamp plate水口推板stripper plateA 板 A plateB 板 B plate支承板support plate方铁spacer plate底针板ejector plate面针板ejector retainer plate回针Return pin导柱Guide pin有托导套Shoulder Guide bush直导套Straight Guide bush动模座板 Bottom clamp plate Moving clamp plate基准线 datum line基准面 datum plan型芯固定板core-retainer plate凸模固定板punch-retainer plate顶针 ejector pin单腔模具single cavity mould多腔模具multi-cavity mould多浇口 multi-gating浇口 gate缺料 starving排气 breathing光泽 gloss合模力 mould clamping force锁模力 mould locking force挤出 extrusion开裂 crack循环时间cycle time老化 aging螺杆 screw麻点 pit嵌件 insert活动镶件movable insert起垩 chalking浇注系统feed system主流道sprue分流道 runner浇口 gate直浇口 direct gate , sprue gate轮辐浇口spoke gate , spider gate点浇口 pin-point gate测浇口 edge gate潜伏浇口submarine gate , tunnel gate 料穴 cold-slug well浇口套 sprue bush流道板 runner plate排飞槽 vent分型线（面） parting line定模 stationary mould ， Fixed mould 动模 movable mould, movable half上模 upper mould ， upper half下模 lower mould ， lower half型腔 cavity凹模 cavity plate ， cavity block拼块 split定位销 dowel定位销孔dowel hole型芯 core斜销 angle pin, finger cam滑块 slide滑块导板slide guide strip楔紧块 heel block, wedge lock拉料杆 sprue puller定位环 locating ring冷却通 cooling channel脱模斜度draft滑动型芯slide core螺纹型芯threaded core热流道模具hot-runner mould绝热流道模insulated runner mould熔合纹 weld line（flow line）三板式模具three plate mould脱模 ejection换模腔模具interchangeable cavity mould 脱模剂 release agent注射能力shot capacity注射速率injection rate注射压力injection pressure差色剂 colorant保压时间holdup time闭模时间closing time定型装置sizing system阴模 female mould ， cavity block阳模 male mould电加工设备Electron Discharge Machining数控加工中心CNC machine center万能铁床 Universal milling machine卧式刨床 Horizontal planer车床 Engine lathe平面磨床Surface grinding machine去磁机 Demagnetization machine万能摇臂钻床Universal radial movable driller 立式钻床 Vertical driller超声波清洗机Ultrasonic clearing machine。
注塑行业术语中英对照表(已打)
ejector bushing
保压过程
Packing Process
ejector guide pillar
保压阶段
Packing stage
cold-slug well
保压时间
packing time
male mold face
潜流效应
underflow effect
mold temperature
gate
多点进浇
multiple gating
gate length
牛顿流体
Newtonian fluid
Gate location
非牛顿流体
non-Newtonian fluid
insert
非均匀收缩
Non-uniform Shrinkage
heel lock
喷嘴
nozzle
cavity plate
脱模
demolding
脱模斜度
draft
脱模困难
ejection difficulties
内应力
internal stress
长链高分子
long chain macromolecules
凝固层比例
frozen layer fraction
取出
removal
ห้องสมุดไป่ตู้
粗加工
rough machining
伺服马达
core-retainer plate
斜度
draft angle
母模面
Famale mold face
动模面
dynnamic mold face
斜槽导板
finger guide plate
注塑常用英语
注塑常用英语Modified by JACK on the afternoon of December 26, 2020一、浇口(入水)：gate浇口进入位置：gate location浇口形式：gate type大水口(2板模)：edge gate, side gate细水口(3板模)：pin-point gate浇口大小：gate size转开关流道：switching runner/gate唧嘴直径：sprue diameter二、流道：runner热流道：hot runner，hot manifold温控箱：temperature controller热嘴冷流道：hot sprue/cold runner唧嘴直流：direct sprue gate圆形流道：round(full/half) runner模流道电脑分析：mold flow analysis流道平衡：runner balance热嘴：hot sprue热流道板：hot manifold发热管：cartridge heater探温针：thermocouples插头：connector plug插座：connector socket密封/封料：seal三、运水：water line喉塞：line plug喉管：tube塑胶管：plastic tube快速接头：jiffy quick connector plug/socket 四、模具零件：mold components三板模：3-plate mold二板模：2-plate mold导柱(边钉/导边)：leader pin/guide pin导套(边司)：bushing/guide bushing?顶针板：ejector retainer plate托板：support plate螺丝：screw管销(管钉)：dowel pin内模管位锁：core/cavity inter-lock顶针：ejector pin司筒：ejector sleeve司筒针：ejector sleeve pin推板：stripper plate缩呵：movable core，return core，core puller 扣机(尼龙拉勾)：nylon latch lock斜顶：lifter模胚(架)：mold base上内模：cavity insert下内模：core insert行位(滑块)：slide镶件：insert压座(斜鸡)：wedge，heeled block耐磨板/油板：wedge wear plate压条：guide way plate?模顶(撑头)：support pillar唧嘴：sprue bushing挡板：stop plate定位圈：locating ring锁扣：latch扣鸡：parting lock set推杆：push bar栓打螺丝： head shoulder screw)杯头螺丝： head cap screw)活动臂：lever arm分流锥：sprue separator垃圾钉：stop pin水隔片：buffle弹弓柱：spring rod弹弓：die spring中托司：ejector guide bush中托导套(边)：ejector guide pin镶针：insert pin波子弹弓：ball catch喉塞：pipe plug行位斜导柱：angle pin斜顶杆：angle ejector rod?复位键/提前回杆：early return bar气阀：valves五、术语：terms承压平面平衡：parting surface support balance模排气：parting line venting回针碰料位：return pin and cavity interference模闭合总厚度：mold base shut height顶针碰运水：water line interferes with ejector pin料位出上(下)模：part from cavity (core) side模胚原身出料位：cavity direct cut on A-plate，core direct cut on B-plate. 不准用镶件： do not use (core/cavity) insert用铍铜做镶件： use beryllium copper insert初步(正式)模图设计：preliminary (final) mold design反呵：reverse core弹弓压缩量：spring compressed length强度不够：insufficient rigidity均匀冷却：even cooling扣前模：sticking热膨胀：thermo expansion公差：tolerance铜电极(铜公)：copper electrode石墨电极：graphite electrode夹线：weld line翘曲：warpage缺胶：short shot困气：air trap毛刺：flash，burr~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~模具述语一、入水：gate进入位：gate location水口形式：gate type大水口：edge gate细水口： pin-point gate水口大小：gate size转水口：switching runner/gate唧嘴口径：sprue diameter二、流道: runner热流道：hot runner,hot manifold热嘴冷流道: hot sprue/cold runner唧嘴直流: direct sprue gate圆形流道：round(full/half runner流道电脑分析：mold flow analysis流道平衡:runner balance热嘴：hot sprue热流道板：hot manifold发热管：cartridge heater探针: thermocouples插头：connector plug插座： connector socket密封/封料： seal三、运水：water line喉塞：line lpug喉管：tube塑胶管：plastic tube快速接头：jiffy quick connector plug/socker 四、模具零件：mold components三板模：3-plate mold二板模：2-plate mold边钉/导边：leader pin/guide pin边司/导套：bushing/guide bushing中托司：shoulder guide bushing中托边L：guide pin顶针板：ejector retainner plate托板：support plate螺丝： screw管钉：dowel pin开模槽：ply bar scot内模管位：core/cavity inter-lock顶针：ejector pin司筒：ejector sleeve司筒针：ejector pin推板：stripper plate缩呵：movable core,return core core puller 扣机（尼龙拉勾）：nylon latch lock斜顶：lifter模胚（架）： mold base上内模：cavity insert下内模：core insert行位（滑块）： slide镶件：insert压座/斜鸡：wedge耐磨板/油板：wedge wear plate压条：plate?撑头: support pillar唧嘴： sprue bushing挡板：stop plate定位圈：locating ring锁扣：latch扣鸡：parting lock set推杆：push bar栓打螺丝：顶板：eracuretun活动臂：lever arm分流锥：spure sperader水口司:bush垃圾钉：stop pin隔片：buffle弹弓柱：spring rod弹弓:die spring中托司：ejector guide bush中托边：ejector guide pin镶针：pin销子：dowel pin波子弹弓：ball catch喉塞: pipe plug锁模块：lock plate斜顶：angle from pin斜顶杆：angle ejector rod尼龙拉勾：parting locks活动臂：lever arm复位键、提前回杆：early return bar气阀：valves斜导边：angle pin术语：terms承压平面平衡：parting surface support balance模排气：parting line venting回针碰料位：return pin and cavity interference模总高超出啤机规格：mold base shut hight顶针碰运水：water line interferes withejector pin料位出上/下模：part from cavith (core) side模胚原身出料位：cavity direct cut on A-plate,core direct cut on B-plate. 不准用镶件： Do not use (core/cavity) insert用铍铜做镶件： use beryllium copper insert初步（正式）模图设计：preliinary (final) mold design反呵：reverse core弹弓压缩量：spring compressed length稳定性好：good stability,stable强度不够：insufficient rigidity均匀冷却：even cooling扣模：sticking热膨胀：thero expansion公差：tolorance铜公(电极）：copper electrode~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~ Surface Appearance 外观Glossiness/gloss finish 光洁度Matt finish/matt surface 毛面Glass fiber rich surface/glass emergence on the surface 玻纤外露Blooming/surface blooming 表面析出White patches on surface 表面白斑Silver marks/silver streak 银纹Splay mark 水纹Flow mark 流纹Weld line 溶结纹Brittle/brittleness 脆Bubbles/trapped gas 气泡Void 孔Burn marks 烧伤FR failed 阻燃不合格Flame rating V-2 阻燃V-2Poor dispersion 分散不好FR/PTFE …agglomerates etc 阻燃剂/PTFE…结块Pellet porous 粒子不密/蜜蜂窝Low impact/tensile etc 物理性能低High flow/filler content etc 流动性/填充…过高Longs/fines/doubles 长粒/碎屑/连粒Poor cut 粒形不好Bristle/voids 表面有小气泡/孔Glass bundles 玻纤结团Product was rejected due to 产品不能接受因为… High moisture level 高水分Warpage/warped 翘曲Shrinkage/shrink 收缩Sink marks 缩影Short shot/short molding 打不满Distortion 变形Over dimension 尺寸过大Under dimension 尺寸过小Flashing 飞边Discoloration 变色Off color 颜色差异Flow rate 流动率Viscous 粘High flow 高流动Low flow 低流动Sticky 粘Mold release 脱模Antioxidant 抗氧剂Flame retardant agent 阻燃剂Heat stabilizer 热稳定剂Chopped glass fiber 短切玻纤Roving glass fiber 粗纱/长玻纤Glass beads 玻璃微珠Milled fiber 碾磨纤Molybdenum disulfide/moly/MoS2 二硫化钼Colorant 着色剂Pigment 颜料Dye 染料Accepted product specification 接受产品规格Approved our product 认可我们的产品Re-set spec 重新定标准Add in extra … 添加多一点…Reduced … content 减少…含量Dropped/reduced … by x％减少…含量…％Confirmed color standard 确认颜色标准Approved color standard 认可颜色标准Re-confirmed color standard 重新确认颜色标准Qualified our product 认可我们的产品Undergoing heat aging test 在做热老化实验Product is under testing 产品在测试当中Received first order 接了第一个定单Expected to finish by … 预计在…完成Expected order is xMT 预计定单量…吨Estimated annual/monthly consumption 预计年/月用量。
注塑专业中英文术语
注塑专业中英⽂术语注塑机参数 Injection Machine Parameter1，注塑机规格参数 Injection Machine Specification①锁紧类型 clamp typea．油缸— hydraulic b．肘杆式— toggle②垂直注塑机导柱间距— tie bar vertical clearance③⽔平注塑机导柱间距— tie bar horizontal clearance④台板尺⼨— platen dim.⑤最⼩ / 最⼤模厚— mold height Min./ Max., Min. / Max. mold thickness⑥最⼩ / 最⼤注塑机开档— open day light Min. / Max.⑦锁紧⾏程— clamp stroke ⑧锁紧⼒— clamping force⑨顶出⾏程— ejector stroke ⑩顶出⼒— ejector force2，试模⼯艺参数 Molding Process Parameter, machine setting①时间 Timer（TM）, seca, 注塑（充填）时间— filling time, injection timeb, 冷却时间— cooling time c, 补缩时间— packing timed, 保压时间— holding time e, 成型周期— cycle time②速率、速度 Velocity, %、speed, in/seca, 注塑（充填）速度— injection speedb, 保压速率— hold pressure velocityc, 螺杆转速— screw rotation speed③压⼒ Pressure（Prs.）, psia, 注塑压⼒— injection pressure b, 保压压⼒— hold pressurec, 回压（背压）— back pressure④温度 Temperature（Temp.）, °Fa, 注塑机喷嘴温度— nozzle temp.b, 料筒前段、中段、后段温度— barrel front、middle、rear temp.c, 模温— mould temp. d, 料温— purged resin melt temp.e, 空射料温— air shot melt temp.产品⼏何 Geometry1．点— point 2．线（边）— line, edge3．⾯ faceA 侧⾯— sideB 表⾯— surfaceC 外观⾯— appearance surface4．壁厚— wall thickness, stock thickness5．加强筋（⾻位）— rib 6．孔— hole7．细长的槽— slot 8．柱位— boss9．⾓—cornerA 圆⾓— filletB 倒⾓— chamferC 尖⾓— sharp corner10．斜度— angle, taper 11. 凹槽—recess , groove⼀．分模信息 Splitting1．分型线— parting line (P/L), splitting line2．主分模⽅向— main direction, line of draw3．浇⼝设定— gating⼆．产品标识 Part Identification1．产品名称— part name (P/N)2．产品编号+版本号— part number + revision (Rev.)3．型腔号— cavity number 4．材料标记— material symbol 5．模具编号— mold number (no.) 6．⽇期印—date code 7．循环印— cycling code 8．公司标志—company logo 三．技术要求 Specification (Special Requirement)1．项⽬启动表 Kick-off sheet5）项⽬启动⽇期— kick off date, start date6）项⽬完成⽇期— due date, lead time7）内模件⽤钢— tool steel8）型腔数量— number of cavities9）数据⽂件编号— data file no.10）注塑材料— resin, plastic, raw material11）收缩率— shrink, shrinkage, shrink factor12）注塑机吨位— molding machine size, injection machine size13）成型周期— cycle time14）型腔光洁度— cavity polish15）型芯光洁度— core polish16）⽪纹（晒纹）— texture, grain17）拔模斜度— draft angle, removal taper18）注塑件颜⾊及光泽— molded color & gloss19）模具加⼯地— manufacturing facility20）热流道供应商— manifold manufacturer, manifold supplier21）浇⼝位置— gate location / position22）浇⼝类型— gate type23）产品标识— stamp information, part identification24）特殊要求— special instructions2．产品质量及外观要求 Part Quality & Appearance Requirement1）尺⼨及公差 Dimension & Tolerance①重要尺⼨— critical dimension, important dim., key dim.②理论尺⼨—nominal dimension ③实际尺⼨— actual dimension⑤公差带—tolerance range ⑥尺⼨超差— dimension deviation⑧拒绝（不合格）— reject, refuse, obsolete, NG⑨让步接受— concession, special admit2）产品缺陷（常见的）Defects (normal)①缩⽔— sink mark, shrinkage ②飞边，⽑边— flash, burr③段差— mismatch discrepancy ④银丝纹，蛇纹—snake marks, streak⑤弯曲，变形— warpage, distortion⑥打不饱（缺料）— short shot ⑦熔接线— weld line⑧多胶— unwanted plastic ⑨拉伤—damage3．产品外观 Part Appearance①产品颜⾊— part color ②产品光泽— gloss③⽪纹粒度— grain4．常⽤词汇、词组及短语 Normal Word, Short Sentence1）单边— per side 2）双边— both sides3）加⼊，添加— add, incorporate 4）去除，取消— remove, cancel5）满⾜…的要求，符合，与…要求⼀致—according to, conform to, satisfy, meet 6）要求，需要— require, need, demand7）确认—be approved, agreed by …8）允许— permit, allow 9）在…范围之内— within10）不可以，不允许，禁⽌— free from, prevent, avoid11）除⾮有另指—… unless otherwise specified12）或少于—…or less13）⾃动化运作— automatic operation14）未注尺⼨（详细形状）见三维造型Non dimensioned contour(detailed shape) see 3D model.15）分型线上的飞边（披缝）或段差应⼩于…Burrs or discrepancy on the P/L shall be … or less.注塑过程专业术语以及分析1, 热注射成型 thermoplastic injection molding2. 控制⾯板 control plat 对设备参数控制的简易操作平台3 显⽰器 pro-face 显⽰设备必要信息的屏幕4 安全门 safe door 防⽌事故发⽣,增⼤安全系数的保护装置门5 注射座 Injection blend 注射成型机组成部件,⽀撑并协助注射的⾦属平台6 螺杆 screw 起旋转计量作⽤的螺纹状部件.是成型机的核⼼机械件7 料膛 fabbrel 树脂预塑的炮膛状部件,和螺杆配合俎件质量要求较⾼8 加热圈 heater 围绕在料膛周围,起迅速并均匀加热作⽤的⽚状加热器9 喷嘴 nozzle 连接注射成型机料筒与模具浇⼝套接触的像针头状的组件10 定模板 plam 可固定模具在成型机上的铁板,是成型机的⼀部分11 动模板 moving plam成型机曲臂连接板,使模具固定在成型机上做开合模运动的动模板12 成型机顶杆 ejector pin 连接到模具上控制模具顶杆顶出或回退作⽤的连接杆13 ⼿动操作 man 只能⼿动单⼀步骤状态操作14 半⾃动操作 sengle man 可半⾃动状态操作15 全⾃动操作 auto 根据设置的程序在全⾃动状态动作16 料膛清洗 purge ⼀般⽤PE料做**动作来清除或淡化料膛内物料或颜⾊17 上料机 loader 在料杯树脂不⾜在传感器监控下吸取储备树脂的成型辅助设备18 温调机，控制模具温度,保持在设定温度以内的温度控制设备19 参数监控画⾯，对设备具体参数设定的画⾯,⼀般配有图表20 ⽣产管理画⾯ product menut 在全⾃动⽣产状态下对产品质量和数量控制的页⾯21 模板控制画⾯ plam control 模板动作状态控制页⾯22 顶出控制画⾯ ejector control 顶出动作状态控制画⾯23 加热管理画⾯ heat control 材料加热控制画⾯24 注射速度画⾯ speed control 注射过程中对速度控制的画⾯25 注射压⼒画⾯ fulling pressure control 注射过程中注射压⼒控制画⾯26 保压控制画⾯ packing pressure control注射后保持设定压⼒提⾼制品质量的控制画⾯27 计量控制画⾯ excit control 计量尺⼨和相关参数控制画⾯28 报警显⽰画⾯ alarm view 设备动作异常或监控报警预览29 最⼤⾼度 maximum daylight 成型机模板打开的最⼤尺⼨30 最⼩⾼度minimum daylight 能满⾜成型机性能的最⼩模具厚度31 锁模⼒ clamping force成型过程中为保证动，定模相互紧密配合⽽需施加的在模具上的⼒32 锁模系统 clamping system 模板控制系统,注塑机上系统的⼀部分33 控制系统 control system 计算机通过检测、处理信息并重新输⼊计算机进⾏控制相关参数34抽芯距 core-pulling distance 将侧型⼼抽⾄不防碍制品脱落的滑块滑动的距离35 抽芯⼒ core-pulling force 从模内的成型塑件中，抽**侧型⼼所需要的⼒36 ⽣产周期 Cycle time ⽣产每个制品的时间或是单位时间内⽣产制品的个数37 液压系统 hydraulic system 液压动⼒注射机上的压⼒系统38 短射 short shot 由于⼀次注射压⼒不⾜或速度偏低引起的浇不⾜现象39 ** jetting 材料⽔份超标,结构不良引起的表⾯⽓泡等不良现象40 ⽩化，制品破坏前变形引起的颜⾊差异41 缩痕 shrinkage 热熔体在收缩情况下表⾯会形成凸凹状现象的统称42 收缩差异 asymmetric shrinkage 制品厚度不均匀或分⼦排列不同引起的不均匀收缩43 熔接线 lines 两股或多股熔体结合位置形成的线状痕迹44 亮线 color change ⼀种有明亮痕迹的注塑成型缺陷，⼀般为线状少为带状45 冷熔接 Cold welding 低温区域的熔接，多见于冲填结束，不同塑料熔前交汇造成46 困⽓ air traps ⼜称包⽓,熔体流动将⽓体堵住或包住不能及时排出47 烧伤 burn 填充时模具内部⽓体不能迅速排出产⽣压缩⾼温,导致制品局部变⾊48⿊斑 black specks 注射成型过程中因⾼温或树脂分解等原因引起的⿊⾊不良现象49 料纹 black streads树脂在模具腔内流动时由于层流因素引起的外观不良现象51 烧焦 burn marks 因⾼温引起的成型缺陷的⼀种52 ⾊差 discoloration制品本⾝颜⾊有其他杂质颜⾊混⼊形成的不良现象53 脆化 brittleness 成型缺陷（因树脂性质发⽣变化引起的脆化或者破裂）54 蠕变 Creep⾼聚物在恒定温度和应⼒下，长度随时间延长⽽逐步深长的现象55 位移 Displacement熔体内部压⼒差引起⾼压部份向低压部分推移现象,可产⽣层次感56 分层表⾯剥离 delamination同⼀树脂或不同树脂发⽣层流后产⽣的现象57 三⾓洲效应 delta effect局部温度差58 ⽅向收缩 diectional shrinkage由⼤分⼦链排列引起的具有⽅向特性的收缩59 尺⼨变化 dimensional variation⽣产出的制品在不同的环境下都会产⽣尺⼨的变化60 尺⼨稳定性 dimensional stability制品尺⼨的稳定性和⼀致性61 密度 Density 单位体积的质量62 翘曲 warpage 有多种原因引起的变形现象,如收缩翘曲,配向翘曲等63 变形 distortion 产品在内应⼒或外⼒的作⽤下产⽣的尺⼨变化以及形状变化64 迟滞 hesitation 熔体的某⼀部份发⽣停⽌流动或极缓慢流动的现象65 垂直于流动⽅向的收缩 cross-flow shrinkage 发⽣在垂直于熔体流动⽅向上的收缩66 热变形温度 deflection temperature热⼒的作⽤下，塑料可以发⽣变形的温度67 脱模 demolding 保压后制品在模具内部成型完毕脱离模具的现象68 脱模斜度 draft ⽅便成型制品脱离模具⽽设计的⾓度69 脱模困难 ejection difficulties 成型制品不容易脱离模具的现象70 内应⼒ internal stress 残留在制品内部因各种原因产⽣的应⼒71 长链⾼分⼦ long chain macromolecules 很多⼩分⼦连接⽽成的具有较⼤质量的长分⼦连72 凝固层⽐例 frozen layer fraction 熔体在模具内冷却状态之⼀的数学表⽰⽅法73 取出 removal 成型后制品拿出的过程74 粗加⼯ rough machining ⽑坯加⼯或留有⼤量余量的待加⼯品75 伺服马达 servomotor 配合CPU⼯作的马达76 ⼯序 workstage 完成⼀个组件或产品经过的步骤77 塑料件 plastic parts 以塑料为原料⽣产的制品78 注射模 injection mould 通过注射⽅式成型的模具79 斜销 angle pin / finger cam 倾斜于分型⾯、随模具的开闭产⽣相对运动的圆柱零件80 斜滑块 angled-lift / splits 斜向镶块或滑动的镶块81 悬臂搭扣连接 cantilever snap joints组合⽅式之⼀82 模套 chase / bolster / frame 使镶件或拼块定位并紧固在⼀起的框套形结构零件83 型芯 Core 成型模具内表⾯突起的组件84 ⽀架 ejector housing / mould base leg 使动模能固定在压机或注塑机上的L型垫块85 推块 ejector pad 在腔内起部分成型作⽤，并在开模时把塑件从型腔内推出的零件86 推杆 ejector pin ⽤于推出塑件或浇注系统凝料的杆件87 推板 ejector plate ⽀撑推出和复位零件，直接传递机床推出⼒的板件88 复位杆 push-pack pin 借助模具的闭合动作，强制推出机构复位的杆件89 浇⼝尺⼨ Gate dimensions(sizes) 浇⼝的相关尺⼨90 直接浇⼝ direct gate ; sprue gate 熔融塑料经主流道直接进⼊型腔的进料⽅式91 盘式浇⼝ disk gate 沿塑料件内圆周扩展进料的浇⼝92 侧浇⼝ edge gate 设置在模具的分型处从塑件的内或外侧进料的⽅式93 扇形浇⼝ fan gate 从分流道道型腔⽅向的宽度逐渐增加的呈扇型的浇⼝94 浇⼝镶块 gating insert 浇⼝以镶块的形式存在95 圆柱头推杆 ejector pin with cylindrical head 头部形状是圆柱型形推杆96 扁顶杆 flat ejector pin ⼯作截⾯为矩形的顶杆97 连接推杆 ejector tie rod 连接推件板与推杆固定板，传递推⼒的杆件98 导套 guide bush 与导柱相配合，⽤于初步确定模具99 导柱 guide pillar 起导向作⽤的部件，⼀般为圆柱体100 浇⼝ gate 连接分流道合型腔的进料通道101 浇⼝长度 gate length 浇⼝的长度102 浇⼝位置 Gate location 树脂流⼊模腔的点相对整体模腔的位置103 嵌件 insert 成型中埋⼊或随后压⼊塑件中的⾦属或其他材料的部件104 楔紧块 heel lock 带有楔⾓,⽤于合模时楔紧滑块的零件105 凹模 cavity plate 成型塑件外表⾯的凹壮零件(包括零件的内腔和实体两部分) 106 凹模拼块 cavity splits 母模中的镶件拼块107 定模座板 fixed clamp plate 使定模固定在注塑机的固定⼯作台⾯上的板件108 顶出系统设计 ejection system design顶出制品机构的类型109 顶出时间ejection time 制品脱离模具可安全取出的时间110 推板导套 ejector bushing 与导柱滑配合，⽤于推出机构导向的圆柱形零件成型⼯艺 Molding technique procedureA 成型⼯艺 Section 1 molding technique.1.成型⼯艺参数类型 Sorts of molding parameter.(1). 注塑参数 Injection parameter.a.注射量 Injection rate.b.计量⾏程Screw back positionc.余料量Cushiond.防诞量Sucking back ratee.螺杆转速Screw speedf.塑化量Plastic0 rateg.预塑背压Screw backpressureh.注射压⼒和保压压⼒Injection pressure and holding pressurei.注射速度Injection speed(2)合模参数Clamping parametera.合模⼒Clamping forceb.合模速度Clamping speedc.合模⾏程.Clamping stroked.开模⼒Opening forcee.开模速度Opening speedf.开模⾏程Opening positiong.顶出压⼒Ejector advance pressure h.顶出速度Ejector advance speedi.顶出⾏程Ejector advance position2.温控参数Temperature parametera.烘料温度Dry resin material temperatureb.料向与喷嘴温度Cylinder temperature and nozzle temperaturec.模具温度Mold temperatured.油温Oil temperature3.成型周期Molding cyclea.循环周期Cycle timeb.冷却时间Cool timec.注射时间Injection timed.保压时间Holding pressure timee.塑化时间Plant timef.顶出及停留时间Knocking out and delay timeg.低压保护时间Mold protect time成型⼯艺参数的设定须根据产品的不同设置.Molding technique parameter setting differs depending on type of product成型条件设定 Molding parameter Setting按成型步骤:可分为开锁模,加热,**,顶出四个过程.Molding steps: mold opening/closing, heating injection and knocking out.开锁模条件:Mold opening parameter: 快速段中速度High-speed mid-speed低压⾼压速度Low pressure high pressure speed锁模条件设定:Mold closing parameter setting1锁模⼀般分: 快速→中速→低压→⾼压Mold closing: high-speed →low-speed →low pressure→ high pressure。
注塑方面英语术语---文本资料
注塑方面英语术语压铸die-cast压炼injection铸件casting/cast/founding起泡/气泡bubble/blister/air bubble缺料shor-shots/undershot浇不足/*铸under-founding多料superfluities/superfluous material(alloy) 顶针痕ejector (pins) mark花纹flow mark/flow line冷纹cold mark/cold streak油纹oil streak走水纹splash mark银纹silver streaks霜纹splay mark夹水纹silver streaks/flow line/weld line扣模/粘模sprue sticking砂眼/气眼air hole（塑胶件）弯曲/变形warping/warpage变形deformation扭曲twist翅曲warp/warped材料错误using wrong plastic material 凸痕convex mark凹位/凹陷sink mark/dent mark披锋flashing批损pare-mark/cut mark批凹pare off锉纹trim-mark/file-mark锉损excessive trim mark黑点/黑纹black spots/black streak发白white mark烧焦burn marks刮花/刮痕scratch mark擦痕/擦伤rub-mark/brush-burn裂缝cracking裂纹craking line碰损stress mark起皮chip错位（合模线）part line misaling ment孔位尺寸改变dimension various哑色dull color表面变光滑（喷油面）glossy finishing表面sruface/outside镶件insert/insert word缩水/收缩sink mark/shrinkage/shrink mark 偏差color deviation色粉colourment颜色colour/color零件污糟dirty mark on part顶白stress mark/ejector mark屈曲bent夹模线移位part line misalignment胶件料厚不均uneven wall thickness水口料degraded material凹印sink mark擦花abrasion mark混色contamination mark热点不良poor heat sticking定位圈locating ring唧嘴sprue bush (浇口套)A板 A plate (定模板)B板 B plate（动模板）方铁spacer block (垫铁)底板bottom clamp plate(动模底板) 面板top clamp plate(定模底板)顶针ejector pin（顶杆）直边钉guide pin (导柱)托司shoulder guide bush(导套)直司straight guide bush(导柱)回针return pin(回程杆)细水口边钉support pin(副导柱)蓝弹簧blue spring（回程弹簧）水口推板runner stripper plate(卸流道板)中边钉ejector guide pin (顶板导柱)顶针板ejector retainer plate(顶杆固定板) 顶针底板ejector plate(顶杆垫板)撑头support pollar（支撑柱）垃圾钉stop pin (限位钉)呵core (后模肉内镶件)后模肉back mold body(后模镶件)前模肉cavity（前模镶件）扣鸡P-lockblister 起泡blooming 起霜blow hole 破孔blushing 泛白body wrinkle 侧壁皱纹breaking-in 冒口带肉bubble 膜泡burn mark 糊斑burr 毛边camber 翘曲cell 气泡center buckle 表面中部波皱check 细裂痕checking 龟裂chipping 修整表面缺陷clamp-off 铸件凹痕collapse 塌陷color mottle 色斑corrosion 腐蚀crack 裂痕crazing 碎裂crazing 龟裂deformation 变形edge 切边碎片edge crack 裂边fading 退色filler speak 填充料斑fissure 裂纹flange wrinkle 凸缘起皱flaw 刮伤flow mark 流痕galling 毛边glazing 光滑gloss 光泽grease pits 污斑grinding defect 磨痕haircrack 发裂haze 雾度incrustation 水锈indentation 压痕internal porosity 内部气孔mismatch 偏模mottle 斑点necking 缩颈nick 割痕orange peel 橘皮状表面缺陷overflow 溢流peeling 剥离pit 坑pitting corrosion 点状腐蚀plate mark 模板印痕pock 麻点pock mark 痘斑resin streak 树脂流纹resin wear 树脂脱落riding 凹陷sagging 松垂saponification 皂化scar 疤痕scrap 废料scrap jam 废料阻塞scratch 刮伤/划痕scuffing 深冲表面划伤seam 裂痕shock line 模口挤痕short shot 充填不足shrinkage pool 凹孔sink mark 凹痕skin inclusion 表皮折迭straightening 矫直streak 条状痕surface check 表面裂痕surface roughening 橘皮状表皮皱折surging 波动sweat out 冒汗torsion 扭曲warpage 翘曲waviness 波痕webbing 熔塌weld mark 焊痕whitening 白化wrinkle 皱纹missing part漏件wrong part错件excessive defects过多的缺陷critical defect极严重缺陷major defect主要缺陷minor defect次要缺陷not up to standard不合规格dimension/size is a little bigger尺寸偏大(小) cosmetic defect外观不良slipped screwhead/slippery screw head螺丝滑头slipped screwhead/shippery screw thread滑手speckle斑点mildewed=moldy=mouldy发霉rust生锈deformation变形burr(金属)毛边flash(塑件)毛边poor staking铆合不良excesssive gap间隙过大grease/oil stains油污inclusion杂质painting peel off脏污shrinking/shrinkage缩水mixed color杂色scratch划伤(Flow Line)流痕(Weld Line) 熔接线Sink Mark凹陷Streak条纹Warpage翘曲。
注塑行业英语词汇
注塑词汇Injection machine 啤机Shot size（weight）实际射胶量 injection volume 理论射胶量 min mold height 最小容模厚度Max mold height 最大容模厚度 Tie bar clearance 拉杆间距 Die plate size 模板尺寸 Ejector stroke 顶出行程 barrel 炮筒，机筒 clamp force 锁模力 non-return valve 止回阀shear 剪切 opening 开模行程Injection pressure 射胶压力back pressure 背压 nozzle size 射咀尺寸Cycle time 循环周期down time 停机时间 hopper 料筒Mold release 脱模剂lubrication 润滑 work horse 主力，主要设备Reserve pressure / packing pressure保压mold trial 试模 shot （一）啤Decompress 减压oven 烤炉，烘灶 shrinkage rate 收缩率Residence time 滞留时间injection speed 注射速度 booster time 增压时间Compression ratio 压缩比 mold close time 合模时间Resin 胶料Plastification 塑化，增塑viscosity 粘性，粘度contamination 污染，杂物Thermoplastic 热塑性塑料thermosetting plastics 热固性塑料Booster time 增压时间 feed 喂料，填充purge 净化Flame retardant 阻燃 degradation 降解，软化 regrind 再粉碎Water absorption 吸水reinforce 增强，加固 specific gravity 比重Elongation 延伸率 density 密度 melting point 熔点Polystyrene 聚苯乙烯（PS） Styrene 苯乙烯Acrylonitrile 丙烯腈Polypropylene 聚丙烯（PP） Polyethylene 聚乙烯 glass fiber 玻纤Condensation 凝固，浓缩 crystalline resin 结晶形塑料compre sion molding 压缩成型flash mold 溢流式模具plsitive mold 挤压式模具split mold分割式模具cavity 型控母模core 模心公模taper 锥拔leather cloak 仿皮革shiver 饰纹flow mark 流痕welding mark 溶合痕post screw insert 螺纹套筒埋值self tapping screw 自攻螺丝striper plate 脱料板piston 活塞cylinder 汽缸套chip 细碎物handle mold 手持式模具（移转成型用模具）encapsulation molding 低压封装成型（射出成型用模具）two plate 两极式（模具）well type 蓄料井insulated runner 绝缘浇道方式hot runner 热浇道runner plat 浇道模块valve gate 阀门浇口band heater 环带状的电热器spindle 阀针spear head 刨尖头slag well 冷料井cold slag 冷料渣air vent 排气道welding line 熔合痕eject pin 顶出针knock pin 顶出销return pin 回位销反顶针sleave 套筒stripper plate 脱料板insert core 放置入子nner stripper plate 浇道脱料板guide pin 导销eject rod (bar)（成型机）顶业捧subzero 深冷处理three plate 三极式模具runner system 浇道系统stress crack 应力电裂orientation 定向sprue gate 射料浇口，直浇口nozzle 射嘴sprue lock pin 料头钩销(拉料杆) slag well 冷料井side gate 侧浇口edge gate 侧缘浇口tab gate 搭接浇口film gate 薄膜浇口flash gate 闸门浇口slit gate 缝隙浇口fan gate 扇形浇口dish gate 因盘形浇口diaphragm gate 隔膜浇口ring gate 环形浇口subarine gate 潜入式浇口tunnel gate 隧道式浇口pin gate 针点浇口Runner less 无浇道(sprue less) 无射料管方式long nozzle 延长喷嘴方式sprue 浇口;溶渣入水：gate 进入位：gate location 水口形式：gate type 大水口：edge gate 细水口： pin-point gate 水口大小：gate size 转水口：switching runner/gate 唧嘴口径：sprue diameter 流道: runner 热流道：hot runner,hot manifold 热嘴冷流道: hot sprue/cold runner 唧嘴直流: direct sprue gate 圆形流道：round(full/half runner 流道电脑分析：mold flow analysis 流道平衡:runner balance 热嘴：hot sprue 热流道板：hot manifold 发热管：cartridge heater 探针: thermocouples 插头：connector plug 插座： connector socket 密封/封料： seal 三、运水：water line 喉塞：line lpug 喉管：tube 塑胶管：plastic tube 快速接头：jiffy quick connector plug/socker 四、模具零件：mold components 三板模：3-plate mold 二板模：2-plate mold 边钉/导边：leader pin/guide pin 边司/导套：bushing/guide bushing 中托司：shoulder guide bushing 中托边L：guide pin 顶针板：ejector retainner plate 托板：support plate 螺丝： screw 管钉：dowel pin 开模槽：ply bar scot 内模管位：core/cavity inter-lock 顶针：ejector pin 司筒：ejector sleeve 司筒针：ejector pin 推板：stripper plate 缩呵：movable core,return core core puller 扣机（尼龙拉勾）：nylon latch lock 斜顶：lifter 模胚（架）： mold base 上内模：cavity insert 下内模：core insert 行位（滑块）： slide 镶件：insert 压座/斜鸡：wedge 耐磨板/油板：wedge wear plate 压条：plate 撑头: support pillar 唧嘴： sprue bushing 挡板：stop plate 定位圈：locating ring 锁扣：latch 扣鸡：parting lock set 推杆：push bar 栓打螺丝：S.H.S.B 顶板：eracuretun 活动臂：lever arm 分流锥：spure sperader 水口司:bush 垃圾钉：stop pin 隔片：buffle 弹弓柱：spring rod 弹弓:die spring 中托司：ejector guide bush 中托边：ejector guide pin 镶针：pin 销子：dowel pin 波子弹弓：ball catch 喉塞: pipe plug 锁模块：lock plate 斜顶：angle from pin 斜顶杆：angle ejector rod 尼龙拉勾：parting locks 活动臂：lever arm 复位键、提前回杆：early return bar 气阀：valves 斜导边：angle pin 术语：terms 承压平面平衡：parting surface support balance 模排气：parting line venting 回针碰料位：return pin and cavity interference 模总高超出啤机规格：mold base shut hight 顶针碰运水：water line interferes withejector pin 料位出上/下模：part from cavith (core) side 模胚原身出料位：cavity direct cut on A-plate,core direct cut on B-plate. 不准用镶件： Do not use (core/cavity) insert 用铍铜做镶件： use beryllium copper insert 初步（正式）模图设计：preliinary (final) mold design 反呵：reverse core 弹弓压缩量：spring compressed length 稳定性好：good stability,stable 强度不够：insufficient rigidity 均匀冷却：even cooling 扣模：sticking 热膨胀：thero expansion 公差：tolorance 铜公(电极）：copper electrode塑料成形模具 mould for plastics 热塑性塑料模 mould for thermoplastics 热固性塑料模 mould for thermosets 压缩模 compression mould 压注模、传递模 transfer mould 注射模 injection mould 热塑性塑料注射模 injection mould for thermoplastics 热固性塑料注射模 injection mould for thermoses 定模 stationary mould fixed half 动模 movable mould moving half 定模座板 fixed clamp plate, top clamping plate. top plate 动模座板 moving clamp plate. bottom clamping plate. bottom plate 上模座板 upper clamping plate 下模座板 lower clamping plate 凹模固定板 cavity-retainer plate 型芯固定板 core-retainer plate 凸模固定板 punch-retainer plate 模套 chase. bolster. frame 支承板 backing plate. supprr plate 垫块 spacer parallel 支架 ejector housing. mould base leg abrasive grinding 强力injection mould 注塑模injection 注射in-line-of-draw 直接脱模insert 嵌件inserted die 嵌入式凹模inspection检查,监督installation安装Surface Appearance 外观Glossiness/gloss finish 光洁度Matt finish/matt surface 毛面Glass fiber richsurface/glass emergence on the surface 玻纤外露Blooming/surface blooming 表面析出White patches on surface 表面白斑Silver marks/silver streak 银纹Splay mark 水纹Flow mark 流纹Weld line 溶结纹Brittle/brittleness 脆Bubbles/trapped gas 气泡V oid 孔Burn marks 烧伤FR failed 阻燃不合格Flame rating V-2 阻燃V-2 Poor dispersion 分散不好FR/PTFE …agglomerates etc 阻燃剂/PTFE…结块Pellet porous 粒子不密/蜜蜂窝Low impact/tensile etc 物理性能低High flow/filler content etc 流动性/填充…过高Longs/fines/doubles 长粒/碎屑/连粒Poor cut 粒形不好Bristle/voids 表面有小气泡/孔Glass bundles 玻纤结团Product was rejected due to 产品不能接受因为… High moisture level 高水分Warpage/warped 翘曲Shrinkage/shrink 收缩Sink marks 缩影Short shot/short molding 打不满Distortion 变形Over dimension 尺寸过大Under dimension 尺寸过小Flashing 飞边Discoloration 变色Off color 颜色差异Flow rate 流动率Viscous 粘High flow 高流动Low flow 低流动Sticky 粘Mold release 脱模Antioxidant 抗氧剂Flame retardant agent 阻燃剂Heat stabilizer 热稳定剂Chopped glass fiber 短切玻纤Roving glass fiber 粗纱/长玻纤Glass beads 玻璃微珠Milled fiber 碾磨纤Molybdenum disulfide/moly/MoS2 二硫化钼Colorant 着色剂Pigment 颜料Dye 染料Accepted product specification 接受产品规格Approved our product 认可我们的产品Re-set spec 重新定标准Add in extra … 添加多一点… Reduced … content 减少…含量Dropped/redu ced … by x％减少…含量…％Confirmed color standard 确认颜色标准Approved color standard 认可颜色标准Re-confirmed color standard 重新确认颜色标准Qualified our product 认可我们的产品Undergoing heat aging test 在做热老化实验Product is under testing 产品在测试当中Received first order 接了第一个定单Expected to finish by … 预计在…完成Expected order is xMT 预计定单量…吨Estimated annual/monthly consumption 预计年/月用量SPC statistic process control 品管保证Quality Assurance 品管控制Quality control 来料检验IQC Incoming quality control 巡检IPQC In-process quality control 校对calibration 动态试验dynamic test 环境试验Environmental test 非破坏性试验non-destructive test 光泽gloss 击穿电压(dielectric) breakdown voltage 拉伸强度tensile strength 冷热骤变试验thermal shock test 环境试验炉Environmental chamber 盐雾实验salt spray test 绝缘电阻测试验仪Insulating resistance meter 内应力internal stress 疲劳fatigue 蠕变creep 试样specimen 撕裂强度tear strength 缩痕shrink mark, sink mark 耐久性durability 抽样sampling 样品数量sample size AQL Acceptable Quality level 批量lot size 抽样计划sampling plan OC曲线operation curve 试验顺序sequence of tests 环境温度ambient temperature 可焊性solderability 阻燃性flame resistance XX电子有限公司XX Electronics CO., Ltd 总经理办公室General manager’s office 企管部Enterprise management department (EM) 行政部Administration department (AD) 销售部Sales department (SD) 财务部Financial department (FD) 技术部Technology department (TD) 物控部Production material control department (PMC) 生产部Production department(PD) 模具部Mold manufacturing department, Tooling manufacturing department (TM) 品管部Quality Assurance department (QA) 冲压车间Stamp workshop, press workshop 注塑车间injection workshop 装配车间Assembly workshop 模具装配车间Mold and die Assembly workshop 金属加工车间metal machine workshop 电脉冲车间Electric discharge process workshop 线切割车间wire cutting process workshop 工磨车间Grinding workshop 总经理General manager (GM) 副总经理Vice-general manager 经理manager 董事长president 副董事长Vice-president XX部门经理Manager of XX department 主任、主管supervisor 拉长Line leader 组长Foreman, forelady 秘书secretary 文员clerk 操作员operator 助理assistant。
注塑常用术语英文表达
1.雾气Moisture Streaks2.玻纤分配不均Glass Fiber Streaks3。
困气Gas Trap Effect4。
银丝纹Sliver Marks5。
结合线Weld Line6。
水波痕Water Wave Effect7.黑点Dark Sport8.顶出印Visible Ejector Marks9。
变形Deformation During Demolding10.填充不足Short Filling11.冷料流痕Cold Slug12。
进胶口点不良Dull Spots Near The Sprue13.喷射痕Jetting14.表面起层Flaking Of The Surface Layer15。
浮泡Entrapped Air16.过热变色Burnt Streaks17.龟裂Stress Crack18。
缩水痕Sink Marks19.真空气泡Density Bubble20。
披锋Flash21.擦伤印Scratch MarksGlass fiber rich surface/glass emergence on the surface22 尺寸过大Over dimension23尺寸过小Under dimension24 翘曲Warpage/warped25 收缩Shrinkage/shrink26 缩影Sink marks27 打不满Short shot/short molding塑料模具mould of plastics注塑模具injection mould冲压模具die模架mould base定模座板Top clamping plateTop plateFixed clamp plate水口推板stripper plateA板A plateB板B plate支承板support plate方铁spacer plate底针板ejector plate面针板ejector retainer plate回针Return pin导柱Guide pin有托导套Shoulder Guide bush直导套Straight Guide bush动模座板Bottom clamp plateMoving clamp plate基准线datum line基准面datum plan型芯固定板core—retainer plate凸模固定板punch—retainer plate顶针ejector pin单腔模具single cavity mould多腔模具multi—cavity mould多浇口multi-gating浇口gate缺料starving排气breathing光泽gloss合模力mould clamping force锁模力mould locking force挤出extrusion开裂crack循环时间cycle time老化aging螺杆screw麻点pit嵌件insert活动镶件movable insert起垩chalking浇注系统feed system主流道sprue分流道runner浇口gate直浇口direct gate , sprue gate轮辐浇口spoke gate , spider gate点浇口pin—point gate测浇口edge gate潜伏浇口submarine gate ，tunnel gate 料穴cold—slug well浇口套sprue bush流道板runner plate排飞槽vent分型线(面）parting line定模stationary mould，Fixed mould动模movable mould，movable half上模upper mould，upper half下模lower mould，lower half型腔cavity凹模cavity plate，cavity block拼块split定位销dowel定位销孔dowel hole型芯core斜销angle pin, finger cam滑块slide滑块导板slide guide strip楔紧块heel block, wedge lock拉料杆sprue puller定位环locating ring冷却通cooling channel脱模斜度draft滑动型芯slide core螺纹型芯threaded core热流道模具hot-runner mould绝热流道模insulated runner mould熔合纹weld line （flow line）三板式模具three plate mould脱模ejection换模腔模具interchangeable cavity mould脱模剂release agent注射能力shot capacity注射速率injection rate注射压力injection pressure差色剂colorant保压时间holdup time闭模时间closing time定型装置sizing system阴模female mould，cavity block阳模male mould电加工设备Electron Discharge Machining数控加工中心CNC machine center万能铁床Universal milling machine卧式刨床Horizontal planer车床Engine lathe平面磨床Surface grinding machine去磁机Demagnetization machine万能摇臂钻床Universal radial movable driller 立式钻床Vertical driller超声波清洗机Ultrasonic clearing machine。
专业英语注塑成型专业词汇
专业英语---注塑成型专业词汇Injection machine 啤机Shot size<weight）实际射胶量 injection volume 理论射胶量 min mold height 最小容模厚度b5E2RGbCAPMax mold height 最大容模厚度 Tie bar clearance 拉杆间距Die plate size 模板尺寸p1EanqFDPwEjector stroke 顶出行程 barrel 炮筒,机筒 clamp force 锁模力 non-return valve 止回阀DXDiTa9E3dshear 剪切 opening 开模行程Injection pressure 射胶压力 back pressure 背压RTCrpUDGiTnozzle size 射咀尺寸Cycle time 循环周期 down time 停机时间hopper 料筒Mold release 脱模剂 lubrication 润滑 workhorse 主力,主要设备5PCzVD7HxAReserve pressure/packing pressure保压 mold trial 试模 shot<一）啤jLBHrnAILgDecompress 减压 oven 烤炉,烘灶 shrinkage rate 收缩率Residence time 滞留时间xHAQX74J0Xinjection speed 注射速度 booster time 增压时间Compression ratio 压缩比LDAYtRyKfEmold close time 合模时间Resin 胶料Plastification 塑化,增塑 viscosity 粘性,粘度contamination 污染,杂物Zzz6ZB2Ltk Thermoplastic 热塑性塑料 thermosetting plastics 热固性塑料Booster time 增压时间dvzfvkwMI1feed 喂料,填充 purge 净化Flame retardant 阻燃degradation 降解,软化rqyn14ZNXIregrind 再粉碎Water absorption 吸水 reinforce 增强,加固specific gravity 比重EmxvxOtOcoElongation 延伸率 density 密度 melting point 熔点Polystyrene 聚苯乙烯<PS）SixE2yXPq5Styrene 苯乙烯 Acrylonitrile 丙烯腈Polypropylene 聚丙烯<PP） Polyethylene 聚乙烯6ewMyirQFLglass fiber 玻纤Condensation 凝固,浓缩 crystalline resin结晶形塑料kavU42VRUsMold materials 模具General-purpose steel 多用途钢 tool steel 模具钢Free-cutting steel 高速切削钢y6v3ALoS89case hardening steel 表面硬化钢 Pre-hardened steel 预硬钢ball and roller bearing steel 滚珠轴承钢M2ub6vSTnP Nonferrous steel 非铁合金 high speed steel 高速钢 cast iron 铸铁Steel specification 钢材规格0YujCfmUCwsteel certification 钢材合格证明书Stainless steel 不锈钢nickel 镍 chrome 铬 aluminum 铝Copper 铜brass 黄铜 bronze 青铜 titanium 钛eUts8ZQVRdProcessing 钢材地加工方法Harding / quench 淬火 nitride 氮化 temper 回火 anneal 退火Roll 轧制 abrasive 研磨,磨损地sQsAEJkW5Tfinish 精加工,抛光<polish）Case-hardening 表面硬化milling machine 铣<锣）床GMsIasNXkALathe车床 drill 钻床 wire cut 线割 NC(numericalcontrol > 数控材料TIrRGchYzgEDM (Electrical discharge machine> 电火花加工 Cut steel 开料Precision ground 精密研磨7EqZcWLZNX heat treatment 热处理 tap 丝锥,攻牙Texture 蚀纹weld 焊接 forge 锻压 deformation 变形lzq7IGf02ESpraying 喷涂 die-cast 压铸Properties 性能Resistance 电阻,抵抗能力 abrasion / wear磨损 erode / corrode 腐蚀Toughness 韧性zvpgeqJ1hkyield strength 屈服强度 tensile strength 拉伸强度Fatigue strength 疲劳强度 break 断裂NrpoJac3v1 stress 应力 hardness 硬度Humidity / moisture 潮湿,湿气roughness 粗糙度 parameter 参数1nowfTG4KIThermal conductivity 导热系数 manufacture 制造,加工drawback 缺点 Ductility 延展性fjnFLDa5Zo grain 晶粒 property 性能,财产 brittleness 脆性GD&T <Geometric Dimensions and Tolerance ）形位尺寸公差Flexural strength 挠曲强度tfnNhnE6e5impact 冲击 conductivity 传导性,导电性Optical 光学地transparent 透明地 insulation 绝缘HbmVN777sL Mechanical 机械地 processability 可加工性能 timeyield 蠕变 Physical 物理地 flow rate 流动速率V7l4jRB8Hscompressive strength 压缩强度Adhesive 粘附地,胶合durability 耐用性83lcPA59W9Mold design 模具设计Tooling specification 模具规格 mould flow 流动模拟sprue nozzle 唧咀孔Clearance 避空,间隙mZkklkzaaP undercut 倒扣 flush 插入,埋入 legend 图例Groove 凹槽latch 插销 class 类型,种类 plan 平面图AVktR43bpw Orifice 孔,口 column 柱位 boss 凸台 standard 标准,规格Rib 骨位 tapered interlock 锥形管位块ORjBnOwcEd Bubbler 炮隆Bolt 螺钉,销顶 identification mark 铭牌P/L strip 锁模片2MiJTy0dTTOverflow well / cold-slug well 冷料井 Vent 排气 pocket 槽Gate location 入水点 full line 实线gIiSpiue7Abroken line 虚线Retainer 固定,支撑 operator 操作者<啤工） receptacle 插座uEh0U1YfmhLifting hole 吊令孔 insulation plate 隔热板 cavity number 型腔号Bolster 支撑,垫子IAg9qLsgBXvent channel 排气槽 leak / filter 渗漏Leak test 试运水 stamp / engrave 雕刻,印记<打字唛）WwghWvVhPE Clamp slot 码模槽 support button / pin 垃圾钉 cut steel 开料Lodge 安装,放置asfpsfpi4kinlay 镶嵌,插入 cam / lifter 斜顶Stripper推方lifting bar 吊模方 sprue 唧咀ooeyYZTjj1 tolerance 公差Counter bore 沉孔 slant 倾斜,斜面conical 圆锥地,圆锥形地BkeGuInkxIBolt 螺栓 manifold 热流道板 prototype tooling 原型实验Gusset 角撑PgdO0sRlMoreverse mold 倒装模 constrain / restrict约束,限制Counter lock 反锁3cdXwckm15thermocouple 热电偶 moldmaker 模具制造商Asset / propertynumber 资产编号h8c52WOngMtool product destination 模具生产地点 Accelerating ejection加速顶出v4bdyGioushydraulic 液压地 pneumatic 气动地Trapezoid 梯形地semi-round 半圆形 format 格式J0bm4qMpJ9baffle 隔水片Electrode 电极,铜公 spare part 配件gall 磨伤,插伤Cable 电缆,电线XVauA9grYP plating / coating <电）镀 bonding / joint 接头Walltransition 壁厚过渡bR9C6TJscwProduct problem 产品问题Troubleshoot 故障处理 reduce(add> plastic 减<加）胶Burr/flash披峰 Burn mark 烧焦pN9LBDdtrdejector mark 顶针印,顶白 black specs 黑点,黑斑Discoloration 混色,污点 gloss 光泽DJ8T7nHuGT jetting/worming 走水纹Sink mark 缩水 void / bubble 气泡,夹气 distortion 变形QF81D7bvUAWarpage 翘曲 short molding / non-fill缺胶,未走齐 Weld line / knit line 夹水线4B7a9QFw9hdiscarded as useless 报废 Split line 夹线 stick in sprue bushing / cavity / core 粘唧咀/前模/后模ix6iFA8xoX Break / crack 顶裂 brittleness 脆性,易脆Others 其他Invoice 发票,清单 vendor(er> 卖方 vendee 买方guideline 方针,指导Intricate 复杂地wt6qbkCyDEconfidential 机密地,不可外泄地 proprietary 私有地Authorize 批准,授权 recipient 接收者Kp5zH46zRkissue ①发布,提供；②问题Approve 确认,赞成requirement 需要,必需物 const 常数,常量Yl4HdOAA61 Regarding 关于,涉及 opposite 相反地,对面地 latitude 纬度,纵向地Version 版本ch4PJx4BlIdefinition 注释,解说 transversal 横向地,截线Profile 轮廓,剖面 eliminate / cancel 取消qd3YfhxCzoallow / permit 允许,许可Respective 各自地,分别地individual 单独地 decrease 减少E836L11DO5increase 增加Preliminary 初步地 approximately 大约,近似estimate / valuate估计,预算S42ehLvE3MAdjust 调整,校准 application 应用,申请 maintain 维持Accurate / precise 精确地501nNvZFissmooth 光滑,顺畅地 device 装置,设备Convenient 方便地deadline 截至日期jW1viftGw9available 有用地,有空地Shift 轮班,换班 critical 关键地,临界地 exceptional 异常地,优异地xS0DOYWHLPExceed 超过 layout 布局,方案 loss 损失,消耗 install 安装,安置 Rotation 旋转LOZMkIqI0witem 条款,工程 quotation 报价 stabilize 稳定Quality 质量 quantity 数量 couple 连接,接合ZKZUQsUJed configuration 构造,外形Illustrate 图解说明 simulation 模拟,仿真recommend 推荐使用dGY2mcoKtT。
- 1、下载文档前请自行甄别文档内容的完整性，平台不提供额外的编辑、内容补充、找答案等附加服务。
- 2、"仅部分预览"的文档,不可在线预览部分如存在完整性等问题,可反馈申请退款(可完整预览的文档不适用该条件!)。
- 3、如文档侵犯您的权益，请联系客服反馈,我们会尽快为您处理(人工客服工作时间：9:00-18:30)。
注塑方面英语术语压铸 die-cast压炼 injection铸件 casting/cast/founding起泡/气泡 bubble/blister/air bubble缺料 shor-shots/undershot浇不足/*铸 under-founding多料 superfluit ies/superfluous material(alloy)顶针痕 ejector (pins)mark花纹 flowmark/flow line冷纹 coldmark/cold streak油纹 oilstreak走水纹 splash mark银纹 silverstreaks霜纹 splaymark夹水纹 silverstreaks/flow line/weld line扣模/粘模 sprue sticking 砂眼/气眼 air hole（塑胶件）弯曲/变形 warping/warpage变形 deformation扭曲 twist翅曲 warp/warped材料错误 using wrongplastic material凸痕 convex mark凹位/凹陷 sink mark/dentmark披锋 flashing批损 pare-mark/cut mark批凹 pareoff锉纹 trim-mark/file-mark锉损 excessive trim mark黑点/黑纹 black spots/blackstreak发白 white mark烧焦 burnmarks刮花/刮痕 scratch mark擦痕/擦伤 rub-mark/brush-burn裂缝 cracking裂纹 craking line碰损 stress mark起皮 chip错位（合模线） part line misaling ment孔位尺寸改变 dimension various哑色 dull color表面变光滑（喷油面） glossy finishing表面sruface/outside镶件insert/insert word缩水/收缩 sinkmark/shrinkage/shrink mark偏差 color deviation色粉 colourment颜色 colour/color零件污糟 dirty mark onpart顶白 stress mark/ejector mark屈曲 bent夹模线移位 part linemisalignment胶件料厚不均 uneven wall thickness水口料 degradedmaterial凹印 sink mark擦花 abrasion mark混色 contamination mark热点不良 poor heatsticking定位圈 locatingring唧嘴 sprue bush (浇口套)A板 Aplate (定模板)B板 Bplate（动模板）方铁 spacer block (垫铁)底板 bottom clamp plate(动模底板)面板 topclamp plate(定模底板)顶针 ejector pin（顶杆）直边钉 guide pin(导柱)托司 shoulder guide bush(导套)直司 straightguide bush(导柱)回针 returnpin(回程杆)细水口边钉 support pin(副导柱)蓝弹簧 blue spring（回程弹簧）水口推板 runner stripperplate(卸流道板)中边钉 ejector guidepin (顶板导柱)顶针板 ejectorretainer plate(顶杆固定板)顶针底板 ejector plate(顶杆垫板)撑头 support pollar（支撑柱）垃圾钉 stop pin(限位钉)呵core (后模肉内镶件)后模肉 back moldbody(后模镶件)前模肉 cavity（前模镶件）扣鸡 P-lockblister 起泡blooming 起霜blow hole 破孔blushing 泛白body wrinkle 侧壁皱纹breaking-in 冒口带肉bubble 膜泡burn mark 糊斑burr 毛边camber 翘曲cell 气泡center buckle 表面中部波皱check 细裂痕checking 龟裂chipping 修整表面缺陷clamp-off 铸件凹痕collapse 塌陷color mottle 色斑corrosion 腐蚀crack 裂痕crazing 碎裂crazing 龟裂deformation 变形edge 切边碎片edge crack 裂边fading 退色filler speak 填充料斑fissure 裂纹flange wrinkle 凸缘起皱flaw 刮伤flow mark 流痕galling 毛边glazing 光滑gloss 光泽grease pits 污斑grinding defect 磨痕haircrack 发裂haze 雾度incrustation 水锈indentation 压痕internal porosity 内部气孔mismatch 偏模mottle 斑点necking 缩颈nick 割痕orange peel 橘皮状表面缺陷overflow 溢流peeling 剥离pit 坑pitting corrosion 点状腐蚀plate mark 模板印痕pock 麻点pock mark 痘斑resin streak 树脂流纹resin wear 树脂脱落riding 凹陷sagging 松垂saponification 皂化scar 疤痕scrap 废料scrap jam 废料阻塞scratch 刮伤/划痕scuffing 深冲表面划伤seam 裂痕shock line 模口挤痕short shot 充填不足shrinkage pool 凹孔sink mark 凹痕skin inclusion 表皮折迭straightening 矫直streak 条状痕surface check 表面裂痕surface roughening 橘皮状表皮皱折surging 波动sweat out 冒汗torsion 扭曲warpage 翘曲waviness 波痕webbing 熔塌weld mark 焊痕whitening 白化wrinkle 皱纹missing part漏件wrong part错件excessive defects过多的缺陷critical defect极严重缺陷major defect主要缺陷minor defect次要缺陷not up to standard不合规格dimension/size is a little bigger尺寸偏大(小) cosmetic defect外观不良slipped screwhead/slippery screw head螺丝滑头slipped screwhead/shippery screw thread滑手speckle斑点mildewed=moldy=mouldy发霉rust生锈deformation变形burr(金属)毛边flash(塑件)毛边poor staking铆合不良excesssive gap间隙过大grease/oil stains油污inclusion杂质painting peel off脏污shrinking/shrinkage缩水mixed color杂色scratch划伤(Flow Line)流痕(Weld Line) 熔接线Sink Mark凹陷Streak条纹Warpage翘曲希望以上资料对你有所帮助，附励志名言3条：1、有志者自有千计万计，无志者只感千难万难。
2、实现自己既定的目标，必须能耐得住寂寞单干。
3、世界会向那些有目标和远见的人让路。