GT系列位移传感器(选型手册)
1GT101DC 速度传感器数据手册说明书

1GT101DC1GT101DCSensing and Productivity SolutionsSpeed Sensors1GT Series Gear Tooth SensorsDESCRIPTIONThe 1GT Series Gear Tooth Sensors use a magnetically biased Hall-effect integrated circuit (IC) to accurately sense movement of ferrous metal targets. This specially designed IC, with discrete capacitor and bias magnet, is sealed in a probe-type package for physical protection and cost-effective installation. Units will function from a 4.5 to 24 Vdc power supply. Output is digital, current sinking (open collector). Reverse polarity protection is standard. If power is inadvertently wiredbackwards, the sensor will not be damaged. Built-in protection against pulsed transients to +60 V, -40 V is also included. Optimum sensor performance is dependent on the following four variables which must be considered in combination:• Target material, geometry, and speed • Sensor/target sensing air gap distance • Ambient temperature• Magnetic material in close proximity VALUE TO CUSTOMERSThe 1GT Series electronically self adjusts to slight variations in runout and temperature, often simplifying installation and maintenance.32315204Issue AFEATURES• Senses ferrous metal targets• Digital current sinking output (open collector)• Better signal-to-noise ratio than variable reluctance sensors (VRS), excellent low speed performance, output amplitude not dependent on RPM• Sensor electronically self-adjusts to slight variations in runout and variations in temperature, simplifying installation and maintenance• Operating frequency range of 50 Hz to 10 kHz • EMI resistant• Reverse polarity protection and transient protection(integrated into Hall-effect IC)• Wide continuous operating temperature range of -40 °C to 150 °C [-40 °F to 302 °F ], short term to 160 °C [320 °F]POTENTIAL APPLICATIONS Transportation• Camshaft and crankshaft speed/position • Transmission speed • Tachometers• Anti-skid/traction control Industrial • Sprocket speed• Chain link conveyor speed and distance • Stop motion detector• High speed, low-cost proximity • Tachometers, countersPORTFOLIOHoneywell’s 1GT Series joins the SNG-Q Series, SNDH-T Series, SNDH-H Series, LCZ Series, and ZH10 Series Speed Sensors.2Sensing and Productivity SolutionsSpeed Sensors1GT Series Gear Tooth Sensors2Guaranteed with maximum external load capacitance of 550 pF.3Based on the target shown in Figure 3; will vary with target geometry.4Operate (degrees) is the angular distance from the leading edge of the tooth to the centerline of the sensor.5Release (degrees) is the angular distance from the trailing edge of the tooth to the centerline of the sensor.NOTICEAbsolute maximum ratings are the extreme limits that the device will withstand without damage to the device. However, theelectrical and mechanical characteristics are not guaranteed as the maximum limits (above recommended operating conditions) areapproached, nor will the device necessarily operate at absolute maximum ratings.3Sensing and Productivity SolutionsSpeed Sensors1GT Series Gear Tooth SensorsFigure 2. Block/Electrical DiagramVoltage regulator 0.22 uF4700 pFTrigger circuit and feedback amplifier circuitOutput (O) open collectorGround (-)Hall-effect sensor ICTarget GuidelinesTable 5 provides basic parameters to follow when an application is not restricted to a specific target. Any target that exceeds these dimensions may be sensed over the entire temperature range of -40 °C to 150 °C [-40 °F to 302 °F] with a sensing air gap up to 2,0 mm [0.080 in].Parameter10 RPM to 3600 RPM.Reference Target and Test Conditions (See Table 6)Parameters will vary due to target size, geometry, location, andmaterial.Table 6. Reference Target Configuration and Evaluation 1, 22Test conditions are:• Sensing air gap = 1,02 mm to 2,03 mm [0.040 in to 0.080 in] • Vsupply = 4.5 Vdc to 24 Vdc.• RPM = 10 RPM min. to 3600 RPM max.Figure 1. Sensor Output Diagram with Sensor Output Diagram (with Pull-up Resistor Added to Output Circuit)Tooth widthSensing air gapSlot widthTooth heightTarget thicknessToothSlotTargetMagnet fieldInductionVsupply 0.4 V max.Speed Sensors1GT Series Gear Tooth SensorsFigure 3. Mounting Dimensions (For reference only. mm/[in].)4Sensing and Productivity SolutionsFind out moreHoneywell serves its customers through a worldwide network of sales offices, representatives and distributors.For application assistance, current specifications, pricing or name of the nearest Authorized Distributor, contact your local sales office.To learn more about Honeywell Sensing and Productivity Solutions’ products, call +1-815-235-6847 or 1-800-537-6945, visit , or e-mail inquiries to *********************Sensing and Productivity Solutions Honeywell1985 Douglas Drive NorthGolden Valley, MN 55422 Warranty/RemedyHoneywell warrants goods of its manufacture as being freeof defective materials and faulty workmanship. Honeywell’sstandard product warranty applies unless agreed tootherwise by Honeywell in writing; please refer to your orderacknowledgement or consult your local sales office for specificwarranty details. If warranted goods are returned to Honeywellduring the period of coverage, Honeywell will repair or replace,at its option, without charge those items it finds defective.The foregoing is buyer’s sole remedy and is in lieu of allother warranties, expressed or implied, including those ofmerchantability and fitness for a particular purpose. In noevent shall Honeywell be liable for consequential, special, orindirect damages.While we provide application assistance personally, through ourliterature and the Honeywell web site, it is up to the customer todetermine the suitability of the product in the application.Specifications may change without notice. The information wesupply is believed to be accurate and reliable as of this printing.However, we assume no responsibility for its use.32315204-A-EN IL50January 2016© 2016 Honeywell International Inc. All rights reserved.ADDITIONAL INFORMATIONThe following associated literature is available on the Honeywell web site at :• Magnetic Sensors Line Guide• Position Sensors Range guide1GT101DC1GT101DC。
位移传感器的选型及常见故障排除方法

位移传感器的选型及常见故障排除方法位移传感器又称为线性传感器,是一种属于金属感应的线性器件,传感器的作用是把各种被测物理量转换为电量。
本文详解位移传感器的选型及常见故障排除方法。
位移传感器的选型位移传感器的选型,要满足下列指标的要求:1、灵敏度方面的技术指标对于一个仪器来说,一般都是灵敏度越高越好的,因为越灵敏,对周围环境发生的加速度的变化就越容易感受到,加速度变化大,很自然地,输出的电压的变化相应地也变大,这样测量就比较容易方便,而测量出来的数据也会比较精确的。
2、零点温度环境温度的变化引起的零点平衡变化。
一般以温度每变化10℃时,引起的零点平衡变化量对额定输出的百分比来表示,即传感器不受压时的输入由温度变更引起的漂移。
3、带宽方面的技术指标带宽指的的是传感器可以测量的有效的频带,比如,一个传感器有上百HZ带宽的就可以测量振动了,一个具有五十HZ带宽的传感器就可以有效测量倾角了。
4、输出方式的技术指标数字输出和模拟输出两种方式。
数字式传感器向仪表输入的是数字信号,如数量、重量等;模拟式传感器向仪表输入的是模拟量信号,如电压、电流等。
5、量程方面的技术指标测量不一样的事物的运动所需要的量程都是不一样的,要根据实际情况来衡量。
6、极限过载传感器能承受的不使其丧失工作能力的最大负荷。
意思是当工作超过此值时,传感器将会受到永久损坏。
7、传感器增益就是传感器的原始信号输出放大倍率。
常见故障及排障方法直线位移传感器的工作原理是跟滑动变阻器一样的,它作为分压器使用的,它是以相对的输出电压来呈现出所测量位置的实际上的位置。
1、如果电子尺已经使用很长时间了,而且密封已经老化,同时夹杂着很多杂质,而且水混合物和油会严重影响电刷的接触电阻的,这样会使显示的数字不停地跳动。
这个时候可以说直线位移传感器的电子尺已经损坏了,需要更换。
2、若电源的容量很小,就会出现很多情况的:熔胶的运动会使合模电子尺的显示变换,有波动,或者合模的运动会使射胶电子尺的显示波动,造成测量结果误差很大。
松下位移传感器HLC2系列使用手册中文高清版

工控编程吧 HL-C2用户手册(专用操作盘编)前言非常感谢您下载本公司“超高速・高精度激光位移传感器 HL-C2系列专用 可编程显示器(GT系列)用画面数据”。
为了您在使用时充分体验本产品的优越性能,请仔细阅读本用户手册,并用正确、适当的方法进行操作。
关于本产品相关的最新信息及最新版用户手册,敬请浏览本公司互联网主页(/id/pidsx/global)。
■请注意1. 本用户手册的插图与实际产品可能稍有差异。
敬请谅解。
2. 将来本用户手册的内容可能修改,以臻完善,恕不另行通知。
3. 禁止擅自复印或者转载本用户手册及软件的部分或全部内容。
4. 本说明书制作过程中虽力求完美,但仍恐有疏漏,若您发现问题或者错误、错页、漏页等,敬请与最近的营业所联系。
5. 有关运用结果,与上述内容无关,恕不承担责任,请见谅。
■关于图标本书中,希望您在使用本产品时遵守如下事项。
除正文以外,请认真读阅这些内容。
工控编程吧 HL-C2用户手册(专用操作盘编)目录前言.....................................................................................................................0 目录 (1)1. 关于HL-C2专用操作盘的引进 (2)1-1 在HL-C2系列上使用GT系列的方法...............................................................................2 1-2 可编程显示器的适用机型............................................................................................3 1-3 引进专用操作盘的流程...............................................................................................4 2. 各部分的名称..................................................................................................5 3. 收集和写入画面数据. (6)3-1 使用条件....................................................................................................................6 3-2 下载专用软件.............................................................................................................8 3-3 安装USB 驱动程序......................................................................................................9 3-4 写入画面数据...........................................................................................................13 4. 与传感器的连接..............................................................................................14 4-1 安装操作盘..............................................................................................................14 4-2 专用操作盘与HL-C2的连接.. (15)工控编程吧 HL-C2用户手册(专用操作盘编)1.关于HL-C2专用操作盘的引进1-1 在HL-C2系列上使用GT系列的方法用户使用“超高速・高精度激光位移传感器HL-C2系列”时,对本公司可编程显示器“GT系列”写入专用画面数据,即可当作专用操作盘使用。
基恩士GT2_kc

12 mm
测量范围
32 mm
12 mm
GT2-A12
GT2-A12K
高精度型
GT2-A32
通用型
精度 : 1 μm (p-p)
精度 : 3 μm (p-p)
精度 : 2 μm (p-p)
无需任何夹具。
由于传感头无需移动,因此无需安装复杂的夹具。 此外还消除了由于夹具而产生的精度错误。
安装简单快速。
无需分度夹具。
90° R
可以经受 2 千万次弯曲而不断裂
W
(“典型”使用情况下)
4
电缆可以在任何位置切割。 自由切割
容易的传感器头安装与设置
[安装/设置步骤数量减少]
使用专用支架轻松完成安装
传统方法
GT2
安装容易且简单, 只需钻一个 10 mm 的孔。
用户必须准备好钻有槽 子的夹具。
设置多个装置时,大指示灯可带来很大便利。
GT2 解决方案 轻松的方式:
显示器
模拟卡
PLC 编程
完成
完成
轻松的方式:
完成
按钮设置
HH、HI、GO、LO、LL 离散输出
“GT2 系列”具有 5 个数字比较器输出(HH、HI、GO、LO 以及 LL),只需几分钟而不是几小时就能完成设置。 此外还具有按钮校正功能,您不妨自问一下为什么还不赶快换用“GT2 系列”。
防尘套(替换用可选购附件)
外观
适用的传感器头 GT2-H12 GT2-H12K GT2-H32 GT2-H50
用于更大的目标
50 mm 范围
低压力型
分辨率 :0.5 μm 准确度 :3.5 μm (P-P)
通用型传感器头 GT2-H50 50 mm 范围传感器头不提供 低压力型。
gt传感器设置说明书

gt传感器设置说明书
1)分L-on与D-on两种模式,L-on为来料触发,D-on为过料触发。
设置方法为:手动按”L/Don”出现“L-on”或者“D-on”,点击左右”按钮即可选择需要使用的模式。
2)长按”mode”按钮3s,进入“easy”模式,接着按一下”MODE”按钮,在“FINE”模式下有3种模式可以选择,FINE模式(正常使用)TURBO模式(用于正常模式检测距离不够的时候),SUPERTURBO(用于检测环境比较差、有灰尘的情况下),按“左右”按钮选择所需要模式后按下“MODE”按钮,选择触时,“SHOT”(单次触发定时器)常用为单次脉冲延时10ms,可以不用设置,接着按“MODE”按钮回到主界面。
设置完成。
涡流传感器,振动,位移选型手册

VB-Z410 轴向位移监测仪、VB-Z410A 胀差监测仪与电涡流传感器 配套使用, 可广泛使用于电力、冶金、石化和造纸行业的大型旋转 机械(如汽轮机、压缩机、电机、风机、泵等)轴向位移、相 对热膨胀的测量和保护控制。
故障监测 监测旋转机械转子的轴向位置或相对热膨胀。 测量参量 转 子 相 对 于 轴 瓦 的 位 置 ( 位 移 )、 热 膨 胀 量 。 机组类型 各种滑动轴承的旋转机械。如汽轮机、压缩机、电机、风机、泵等。 技术参数 输 入: 电涡流传感器,1 路信号输入 输入阻抗: 20K Ω 精 度: 指示误差 1% ,标准输出 1% 运行指示: 传感器 OK 绿色 LED 亮
2 VB-Z系列旋转机械在线监测保护系统的构成
VB-Z 系列旋转机械在线监测保护系统主要分为盘装表、框架表、变送器三种类 型,和各种传感器配套,满足用户的不同使用要求。 2.1 轴向位移
轴向位移测量可用来描述止推环法兰和止推轴承之间的相对位置。对于一台大型旋 转机械来说,轴向位移是重要的测量参数之一。轴向位移的测量主要目的是为了保证消 除机器转子与定子之间的磨擦。轴向止推轴承故障可能是最严重的机器故障,因此,必 须对大型旋转机械轴的窜动量进行在线监测,以防止发生这种类型的故障,保护机器的 安全。
7
VB-Z430 双通道瓦振监测仪
8
VB-Z440/440A 智能转速 / 零转速检测仪
激光位移传感器操作手册说明书

激光位移传感器操作手册V2.0目录第1章:产品概要......................................................................... 1-11.1 包装内容 ......................................................................................... 1-11.2 各部件名称及功能........................................................................... 1-21.3 安装................................................................................................. 1-3 第2章:设定与测量 ..................................................................... 2-1 第3章:软件操作......................................................................... 3-13.1 通信设置 ......................................................................................... 3-13.2 位置读取与归零设定 ....................................................................... 3-2 第4章:通讯指令......................................................................... 4-14.1 通讯参数列表 .................................................................................. 4-14.2 通讯协议 ......................................................................................... 4-4 第5章:产品规格......................................................................... 5-1 第6章:安全注意事项.................................................................. 6-1 第7章:保固 ................................................................................ 7-1版本更新历程激光位移计操作手册V2.0版本更新历程版本更新日期V1.0 第一版发行2018/09/03V2.0 新增「反应速度设定」与「中值滤波器设定」功能说明与通讯地址设定方式。
位移传感器-矿用位移传感器使用说明书

GUD1200矿用本安型位移传感器产品使用说明书2013年1月5日目录1. 概述 (3)1.1 主要用途及使用范围 (3)1.2 型号组成及代表意义 (3)1.3 使用环境条件 (3)2 结构特征与工作原理 (3)2.1 结构 (4)2.2 工作原理 (4)3 技术特性 (4)3.1 产品执行标准 (4)3.2 主要性能 (4)3.3 主要参数 (4)3.4尺寸重量 (4)3.4.1 尺寸 (4)3.4.2 重量 (4)4 安装、调试 (4)4.1 安装条件、技术要求 (4)5 使用、操作 (5)6 故障分析与排除 (5)7 注意事项 (5)8 运输、贮存 (6)9 开箱及检查 (6)10 订货 (6)使用本产品前,请详细阅读本说明书。
GUD1200矿用本安型位移传感器1.概述1.1主要用途及使用范围矿用本安型位移传感器主要用于煤矿采煤工作面液压支架位移量的测量,其工作简单可靠,能够直观显示位置信号,避免常规的电器产品中电气电路经常出现问题的弊端。
传感器内部为干簧管及电阻,属简单设备。
传感器防爆型式为矿用本安型,防爆标志:“Exib I”。
1.2型号组成及代表意义1.3使用环境条件——环境温度-5℃~40℃;——海拔高度不超过2000m;——空气相对湿度不大于95%(25℃时);——在有瓦斯、煤尘爆炸危险的场所;——在无破坏绝缘的腐蚀性气体或蒸汽的场所;——在无显著振动和冲击的场所;——污染等级为3级;——安装类别为Ⅲ类。
2结构特征与工作原理2.1结构图1 结构图2.2工作原理指示环固定在液压支架上,当液压支架位移发生变化时带动指示环前后动作,指示环上封装有磁铁,在传感器杆体每0.05m处分别装有干黄管,当磁铁接近干簧管时,导致干簧管接通。
3技术特性3.1产品执行标准本产品执行标准GB3836-2010、Q/0104ZMD047—2013。
3.2主要性能--输入电压:DC12V;3.3主要参数3.3.1 电压:DC12V;3.3.2 接点容量:12V/1A。
- 1、下载文档前请自行甄别文档内容的完整性,平台不提供额外的编辑、内容补充、找答案等附加服务。
- 2、"仅部分预览"的文档,不可在线预览部分如存在完整性等问题,可反馈申请退款(可完整预览的文档不适用该条件!)。
- 3、如文档侵犯您的权益,请联系客服反馈,我们会尽快为您处理(人工客服工作时间:9:00-18:30)。
Model
Communication Method Connection
Device
Judgment result
readout
Measurement
Value readout Control
Input
Control Output
Remarks
DL-RS1A RS-232C
PLCs Computers
○○○○×
Use RS-232C Protocol
Communication. Communicate after creating a Communication Program.
DL-RB1A BCD Output
PLCs Computers
×○×××
The measured value can be synchronized with a trigger input or updated via a timer. Output values are synchronized with the strobe output.
The ◎ mark indicates that wire reduction and the creation of a Communication Program is not necessary.
Wire-saving
Sensor Amplifier
CCD Thru-beam Type Digital Laser Sensor
IG Series
Contact Sensor
GT2/GT Series
PLC
DL-DN1
DeviceNet PLCs ◎◎◎◎×
Use I/O Communication. Not necessary to create a communication program. Use Explicit Messages to change settings.
NEW
EtherNet/
IP Communication Unit DL-EP1NEW
DL-EP1
EtherNet/IP PLCs ◎◎◎◎◎
Use the cyclic communication. Not necessary to create a communication program. Use message communication to change settings.NEW
NEW
Communication Unit
DL Series
Open Field Network Communication Units
Achieving great wire-saving with the NEW Open Field Network Communication Units
Thru-beam Type
Laser Detection Sensor
IB Series
L I N E U P
DeviceNet
Communication Unit DL-DN1NEW
N E W R E L E A S E
WW1-1031
www.keyence .com
Please visit:
SINGAPORE
Phone: +65-6392-1011 Fax: +65-6392-5055SLOVAKIA
Phone: +421 2 5939 6461 Fax: +421 2 5939 6200
MEXICO
Phone: +52-81-8220-7900 Fax: +52-81-8220-9097NETHERLANDS
Phone: +31 40 20 66 100 Fax: +31 40 20 66 112POLAND
Phone: +48 71 36861 60 Fax: +48 71 36861 62MALAYSIA
Phone: +60-3-2092-2211 Fax: +60-3-2092-2131CZECH REPUBLIC
Phone: +420 222 191 483 Fax: +420 222 191 505AUSTRIA
Phone: +43 22 36-3782 66-0 Fax: +43 22 36-3782 66-30BELGIUM
Phone: +32 1 528 1222 Fax: +32 1 520 1623CHINA
Phone: +86-21-68757500 Fax: +86-21-68757550CANADA
Phone: +1-905-696-9970 Fax: +1-905-696-8340FRANCE
Phone: +33 1 56 37 78 00 Fax: +33 1 56 37 78 01
KOREA
Phone: +82-31-642-1270 Fax: +82-31-642-1271
GERMANY
Phone: +49 61 02 36 89-0 Fax: +49 61 02 36 89-100HUNGARY
Phone: +36 1 802 73 60 Fax: +36 1 802 73 61HONG KONG
Phone: +852-3104-1010 Fax: +852-3104-1080ITALY
Phone: +39-02-6688220 Fax: +39-02-66825099JAPAN
Phone: +81-6-6379-2211 Fax: +81-6-6379-2131SWITZERLAND
Phone: +41 43-45577 30 Fax: +41 43-45577 40THAILAND
Phone: +66-2-369-2777 Fax: +66-2-369-2775TAIWAN
Phone: +886-2-2718-8700 Fax: +886-2-2718-8711UK & IRELAND
Phone: +44-1908-696900 Fax: +44-1908-696777USA
Phone: +1-201-930-0100 Fax: +1-201-930-0099
KEYENCE GLOBAL HEADQUARTERS
1-3-14, Higashi-Nakajima, Higashi-Yodogawa-ku, Osaka, 533-8555, Japan Phone: +81-6-6379-2211
Copyright (c) 2011 KEYENCE CORPORA TION. All rights reserved.DL-WW-L-E 1031-1 600956 Printed in Japan
The information in this publication is based on KEYENCE’s internal research/evaluation at the time of release and is subject to change without notice.*
6
9
5
6
*
Unit : mm
Supported Sensor Amplifiers (as of March 1st, 2011)
GT2 Series/GT-70A Series/IG Series*1/ IB Series*2/ IL Series*3
*1 DL-RS1A units purchased on or before July 14th, 2009 cannot be used. *2 DL-DN1 units purchased on or before July 14th, 2010 cannot be used. *3 DL-EP1/DL-DN1 is not supported. Inquire separately concerning compatibility conditions
DL-DN1DL-RS1A DL-RB1A
DL-EP1
D I M
E N S I O N S。