公制、英制、美制螺纹标准钻孔底径大全 2016.03.08
公制、英制、美制、各种螺纹钻孔标准
公 制 细螺纹
规格 M1.0x0.2 M1.1x0.2 M1.2x0.2 M1.4x0.2 M1.6x0.2 M1.7x0.2 M1.8x0.2 M2.0x0.25 M2.2x0.25 M2.3x0.25 M2.5x0.35 M2.6x0.35 M3.0x0.35 M3.5x0.35 M4.0x0.5 M4.5x0.5 M5.0x0.5 M5.5x0.5 M6.0x0.75 M6.0x0.5 M7.0x0.75 M7.0x0.5 M8.0x1.0 M8.0x0.75 M8.0x0.5 M9.0x1.0 M9.0x0.75 M10x1.25 M10x1.0 M10x0.75 M10x0.5 M11x1.0 M11x0.75 M12x1.5 M12x1.25 M12x1.0 M12x0.5 M14x1.5 M14x1.0 M15x1.5 M15x1.0 M16x1.5 标准径 0.80 0.90 1.00 1.20 1.40 1.45 1.60 1.75 1.95 2.05 2.20 2.20 2.70 3.20 3.50 4.00 4.50 5.00 5.30 5.50 6.30 6.50 7.00 7.30 7.50 8.00 8.30 8.80 9.00 9.30 9.50 10.00 10.30 10.50 10.80 11.00 11.50 12.50 13.00 13.50 14.00 14.50 2级牙钻孔径 最大 0.821 0.921 1.021 1.221 1.421 1.500 1.621 1.785 1.985 2.061 2.221 2.246 2.721 3.221 3.599 4.099 4.599 5.099 5.378 5.550 6.378 6.550 7.153 7.378 7.520 8.153 8.378 8.912 9.153 9.378 9.520 10.153 10.378 10.676 10.912 11.153 11.520 12.676 13.153 13.676 14.153 14.676 最小 0.783 0.883 0.983 1.183 1.383 1.460 1.583 1.729 1.929 2.001 2.121 2.186 2.621 3.121 3.459 3.959 4.459 4.959 5.188 5.400 6.188 6.400 6.917 7.188 7.400 7.917 8.188 8.647 8.917 9.188 9.400 9.917 10.188 10.376 10.647 10.917 11.400 12.376 12.917 13.376 13.917 14.376 规格
各种制式螺纹攻牙钻孔径和滚造径对照表
各种制式螺纹攻牙钻孔径和滚造径对照表，太全了金属加工2015-10-17 关注作者原文地址本表所推选钻头孔径，是针对攻牙加工时，能够很容易的了解钻头直径；而依据市售之标准钻头所选定的。
在使用钻头的情况下，由于钻头的形状及尺寸、精度、被钻孔之材质等，对于所钻孔的尺寸，精度有很大影响，所以使用本表之钻孔径，若有不当之处，应实际状况适当的变更钻头直径，本表依据2级牙制订。
公制精螺纹规格标准径2级牙钻孔径最大最小M1.0×0.25 0.75 0.785 0.729M1.1×0.25 0.85 0.885 0.829M1.2×0.25 0.95 0.985 0.929M1.4×0.3 1.10 1.142 1.075M1.6×0.35 1.25 1.321 1.221M1.7×0.35 1.35 1.421 1.321M1.8×0.35 1.45 1.521 1.421M2.0×0.4 1.60 1.679 1.567M2.2×0.45 1.75 1.838 1.713M2.3×0.4 1.90 1.979 1.867M2.5×0.45 2.10 2.138 2.013M2.6×0.45 2.20 2.238 2.113M3.0×0.5 2.50 2.599 2.459M3.0×0.6 2.40 2.44 2.280M3.5×0.6 2.90 3.010 2.850M4.0×0.7 3.30 3.422 3.242M4.0×0.75 3.25 3.326 3.106M4.5×0.75 3.80 3.878 3.688M5.0×0.8 4.20 4.334 4.134M5.0×0.9 4.10 4.170 3.930M6.0×1.0 5.00 5.153 4.917M7.0×1.0 6.00 6.153 5.917M8.0×1.25 6.80 6.912 6.647M9.0×1.25 7.80 7.912 7.647M10×1.5 8.50 8.676 8.376M11×1.5 9.50 9.676 9.376M12×1.75 10.30 10.441 10.106M14×2.0 12.00 12.210 11.735M16×2.0 14.00 14.210 13.835M18×2.5 15.50 15.744 15.294M20×2.5 17.50 17.744 17.294M22×2.5 19.50 19.744 19.294M24×3.0 21.00 21.252 2.752M27×3.0 24.00 24.252 23.752M30×3.5 26.50 26.771 26.211公制细螺纹规格标准径2级牙钻孔径最大最小M1.0×0.2 0.80 0.821 0.783M1.1×0.2 0.90 0.921 0.883M1.2×0.2 1.00 1.021 0.983M1.4×0.2 1.20 1.221 0.183M1.6×0.2 1.40 1.421 1.383M1.7×0.2 1.45 1.500 1.460M1.8×0.2 1.60 1.621 1.583M2.0×0.25 1.75 1.785 1.729M2.2×0.25 1.95 1.985 1.929M2.3×0.25 2.05 2.061 2.001M2.5×0.35 2.20 2.221 2.121M2.6×0.35 2.20 2.246 2.186M3.0×0.35 2.70 2.721 2.621M3.5×0.35 3.20 3.221 3.121M4.0×0.5 3.50 3.599 3.459M4.5×0.5 4.00 4.099 3.959M5×0.5 4.50 4.599 4.459M5.5×0.5 5.00 5.099 4.959M6.0×0.75 5.30 5.378 5.188M6.0×0.5 5.50 5.550 5.400M7.0×0.75 6.30 6.378 61.88M7.0×0.5 6.50 6.550 64.00M8.0×1.0 7.00 7.153 6.917M8.0×0.75 7.30 7.378 7.188M8×0.5 7.50 7.520 7.400M9×1.0 8.00 8.153 7.917M9×0.75 8.30 8.378 8.188M10×1.25 8.80 8.912 8.647M10×1.0 9.00 9.153 8.917M10×0.75 9.30 9.378 9.188M10×0.5 9.50 9.520 9.400M11×1.0 10.00 10.153 9.917M11×0.75 10.30 10.378 10.188 M11×1.5 10.50 10.676 10.376M12×1.25 10.80 10.912 10.647 公制细螺纹规格标准径2级牙钻孔径最大最小M12×1.0 11.00 11.153 10.917M12×0.5 11.50 11.520 11.4M14×1.5 12.50 12.676 12.376M14×1.0 13.00 13.153 12.917 M15×1.5 13.50 13.676 13.376 M15×1.0 14.00 14.153 13.917 M16×1.5 14.50 14.676 14.376 M16×1.0 15.00 15.153 14.917 M17×1.5 15.50 15.676 15.376 M17×1.0 16.00 16.153 15.917 M18×2.0 16.00 16.210 15.835 M18×1.5 16.50 16.670 16.376 M18×1.0 17.00 17.153 16.917 M20×2.0 18.00 18.210 17.835 M20×1.5 18.50 18.676 18.376 M20×1.0 19.00 19.153 18.917 M20×2.0 20.00 20.210 19.835 M22×1.5 20.50 20.676 20.376 M22×1.0 21.00 21.153 20.917 M24×2.0 22.00 22.210 21.835 M24×1.5 22.50 22.676 22.376 M24×1.0 23.00 23.153 22.917 M25×2.0 23.00 23.210 22.835 M25×1.5 23.50 23.676 23.376 M25×1.0 24.00 24.153 23.917 M26×1.5 24.50 24.676 24.376 M27×2.0 25.00 25.210 24.835 M27×1.5 25.50 25.676 25.376 M27×1.0 26.00 26.153 25.917 M28×2.0 26.00 26.210 25.835 M28×1.5 26.50 26.676 26.376 M28×1.0 27.00 27.153 26.917 M30×3.0 27.00 27.252 26.752 M30×2.0 28.00 28.210 27.835 M30×1.5 28.50 28.676 28.376 M30×1.0 29.00 29.153 28.917 M32×2.0 30.00 30.210 29.835 M32×1.5 30.50 30.676 30.376 M33×3.0 30.00 30.252 29.752 M33×2.0 31.00 31.210 30.835 M33×1.5 31.50 31.376 31.376 M35×1.5 33.50 33.676 33.376 M36×3.0 33.00 33.252 32.752 M36×2.0 34.00 34.210 33.835 M36×1.5 34.50 34.676 34.376 美制细螺纹规格(UNF) 标准径2级牙钻孔径最大最小番数牙外径NO.0-80(1.524) 1.25 1.305 1.182 NO.1-72(1.854) 1.55 1.612 1.474 NO.2-64(2.184) 1.85 1.912 1.756 NO.3-56(2.515) 2.10 2.197 2.025 NO.4-48(2.845) 2.40 2.458 2.271 NO.5-44(3.175) 2.70 2.740 2.551 NO.6-40(3.505) 2.90 3.022 2.820 NO.8-36(4.166) 3.50 3.606 3.404 NO.10-32(4.826) 4.10 4.165 3.963 NO.12-28(5.846) 4.60 4.724 4.496 1/4 -28 5.50 5.588 5.3605/16 -24 6.90 7.035 6.7823/8 -24 8.50 8.636 8.3827/16 -20 9.90 10.033 9.7291/2 -20 11.50 11.607 11.3299/16 -18 12.90 13.081 12.7515/8 -18 14.50 14.681 14.3513/4 -16 17.50 14.678 17.3237/8 -14 20.50 20.675 20.2701 -12 23.20 23.571 23.1141-1/8 -12 26.50 26.746 26.2891-1/4 -12 29.50 29.921 29.4641-3/8 -12 32.80 33.096 32.4641-1/2 -12 36.00 36.270 35.814无屑丝攻钻孔径规格精度等级RH4.5.6 RH7.8 RH9M1.0×0.25 0.86 0.88 -M1.1×0.25 0.96 0.98 -M1.2×0.25 1.06 1.08 -M1.4×0.3 1.24 1.25 -M1.6×0.35 1.41 1.43 -M1.7×0.35 1.51 1.53 -M1.8×0.35 1.61 1.63 -M2.0×0.4 1.78 1.80 -M2.2×0.45 1.95 1.98 -M2.3×0.4 2.08 2.10 -M2.5×0.45 2.25 2.28 -M2.6×0.45 2.35 1.38 -M3.0×0.5 2.73 2.75 -M3.0×0.6 3.17 3.20 -M4.0×0.7 3.62 3.65 3.69M5.0×0.8 4.56 4.60 4.64M6.0×1.0 5.45 5.50 5.55M7.0×1.0 6.45 6.50 6.55M8.0×1.25 7.31 7.38 7.44M10×1.5 9.18 9.25 9.32M10×1.25 9.31 9.38 9.44M12×1.75 11.04 11.12 11.21M12×1.25 11.31 11.38 11.44注:无槽丝攻之钻孔径,在上表所列之数值,由于被加工材料之材质、硬度、形状、尺寸等之影响,多少会有所变动，因此参考上表之同时,亦请增减若干.美制管螺纹规格(UNEF) 标准径2级牙钻孔径最大最小NO.12 -32 4.70 4.826 4.6231/4 -32 5.60 5.690 5.4865/16 -32 7.10 7.264 7.0873/8 -32 8.70 8.865 8.6617/16 -28 10.20 10.338 10.1351/2 -28 11.80 11.938 11.7099/16 -28 13.20 13.386 13.1325/8 -24 14.80 14.986 14.7323/4 -20 17.80 17.958 17.6787/8 -20 21.00 21.133 20.8531 -20 24.00 24.308 24.028美制粗螺纹规格(UNC) 标准径2级牙钻孔径番数牙外径最大最小NO.1-64(1.854) 1.55 1.582 1.425NO.2-56(2.184) 1.80 1.871 1.695NO.3-48(2.515) 2.10 2.146 1.941NO.4-40(2.845) 2.30 2.385 2.157NO.5-40(3.175) 2.60 2.697 2.487NO.6-32(3.505) 2.80 2.895 2.642NO.8-32(4.166) 3.40 3.530 3.302NO.10-24(4.826) 3.90 3.962 3.682NO.12-24(5.846) 4.50 4.597 4.3441/4 -20 5.10 5.257 4.9795/16 -18 6.60 6.731 6.4013/8 -16 8.00 8.153 7.9877/16 -14 9.40 9.500 9.1441/2 -13 10.80 11.023 10.5929/16 -12 12.20 12.446 11.9895/8 -11 13.60 12.868 13.3863/4 -10 16.20 16.840 16.3071 -8 22.20 22.606 21.9711-1/8 -7 25.00 25.349 24.6381-1/4 -7 28.20 28.524 27.8131-3/8 -6 30.80 31.115 30.3531-1/2 -6 34.00 34.290 33.5281-3/4 -5 39.50 39.827 38.9642 -4-1/2 45.20 45.593 44.679英制螺纹规格钻孔径硬材软材W1/8 - 40 2.65 2.60W5/32 - 32 3.25 3.20W3/16 - 24 3.75 3.70W1/4 - 20 5.10 5.00W5/16 - 18 6.60 6.50W3/8 - 16 8.00 7.90W7/16 - 14 9.40 9.30W1/2 - 12 10.70 10.50W9/16 - 12 12.30 12.00W5/8 - 11 13.70 13.50W3/4 - 10 16.70 16.50W7/8 - 9 19.50 19.30W1 - 8 22.40 22.00W1-1/8 - 7 25.00 24.80W1-1/4 - 7 28.30 28.00英制管螺纹规格标准径钻孔径最大最小PS1/16 -28 6.50 6.632 6.490PS1/8 -28 8.50 8.637 8.495PS1/4 - 19 11.40 11.549 11.341PS3/8 - 19 15.00 15.054 14.846PS1/2 - 14 18.50 18.773 18.489PS3/4 - 14 24.00 24.259 23.975PS1 - 11 30.20 30.471 30.111PS1-1/4 -11 38.80 39.132 38.772PS1-1/2 -11 44.80 45.025 44.665PS2 - 11 56.50 56.836 56.476英制管螺纹规格标准径有效牙部之长度(最小)中之母螺牙内径标准长度(最小)中之母螺牙内径使用绞刀时不用绞刀时PT1/16 -28 6.10 6.2 6.244 6.384PT1/4 -19 10.70 11 10.962 11.174PT3/8 -19 14.20 14.5 14.448 14.658PT1/2 -14 17.60 18 17.979 18.263PT3/4 -14 23.00 23.5 23.378 23.663Pt1 -11 29.00 29.5 29.459 29.822PT1-1/4 -11 37.50 38 37.976 38.339 PT1-1/2 -11 43.40 44 43.869 44.232 Pt2 -11 54.90 55.5 55.412 55.844美制螺纹滚造径规格钻孔径NPT NPS使用绞刀时不用绞刀时1/16 -27 6.1 6.25 6.351/8 -27 8.33 8.43 8.741/4 -18 10.72 11.13 11.133/8 -18 14.27 14.27 14.681/2 -14 17.48 17.86 18.263/4 -14 22.63 23.01 23.421 -11-1/2 28.58 28.98 29.361-1/4-11-1/2 37.31 37.69 38.11-1/2-11-1/2 43.66 44.04 44.452 -11-1/2 55.58 55.96 56.36英制螺纹滚造径规格滚造径W 3/16 - 24 4.08 - 4.05W 1/4 - 20 5.51 - 5.46W 5/16 - 18 7.01 - 6.95W 3/8 - 16 8.48 - 8.41W 7/16 - 14 9.92 - 9.85W 1/2 - 12 11.31 - 11.24W 9/16 -12 12.89 - 12.82公制螺纹规格滚造径M3.0×0.5 2.63 2.60M3.0×0.6 2.56 2.53M3.5×0.6 3.06 3.03M4.0×0.7 3.49 3.45M4.0×0.75 3.45 3.41M4.5×0.75 3.96 3.92M5.0×0.8 4.43 4.38M5.0×0.9 4.36 4.31M6.0×1.0 5.30 5.25M7.0×1.0 6.30 6.25M8.0×1.0 7.28 - 7.23M8.0×1.25 7.12 - 7.07M9.0×1.25 8.12 - 8.07M10×1.25 9.10 - 9.04M10×1.5 8.97 - 8.91M11×1.5 9.97 - 9.91M12×1.5 10.92 - 10.87M12×1.75 10.79 - 10.73 M14×2.0 12.63 - 12.56M16×2.0 14.63 - 14.56M18×2.5 16.31 - 16.23M20×2.5 18.31 - 18.23M22×2.5 20.31 - 20.23针车用螺纹规格(UNC) 滚造径SM 1/8 40 2.735 -2.688 SM 1/8 44 2.769 -2.722 SM 9/64 40 3.128 -3.083 SM 11/64 40 3.855 -3.805 SM 3/16 32 4.205 -4.155 SM 3/16 28 4.143 -4.093 SM 7/32 32 5.003 -4.955 SM 15/64 28 5.325 -4.955 SM 1/4 40 5.890 -5.735 SM 1/4 28 5.721 -5.366 SM 9/32 28 6.528 -6.648 SM 11/32 28 8.092 -8.432 SM 3/8 29 8.880 -8.015 SM 7/16 30 10.466 -10.401 SM 7/16 16 10.037 -9.967 SM 1/2 20 11.819 -11.749 SM 9/16 20 13.400 -13.425 美制粗螺纹规格(UNC) 滚造径NO.5-40 2.70 - 2.67NO.6-32 2.95 - 2.91NO.8-32 3.60 - 3.57NO.10-24 4.09 - 4.05NO.12-24 4.75 - 4.701/4 -20 5.50 - 5.455/16 -18 6.98 - 6.933/8 -16 8.45 - 8.407/16 -14 9.89 - 9.831/2 -13 11.39 - 11.329/16 -12 12.87 - 12.80美制细螺纹规格(UNF) 滚造径NO.5-44 2.73 - 2.70NO.6-40 3.05 - 3.02NO.8-36 3.66 - 3.63NO.10-32 4.26 - 4.80NO.12-28 4.84 - 4.801/4 -28 5.72 - 5.685/16 -24 7.20 - 7.163/8 -24 8.79 - 8.747/16 -20 10.23 - 10.181/2 -20 11.82 - 11.76本表所推选钻头孔径,是针对攻牙加工时,能够很容易的了解钻头直径;而依据市售之标准钻头所选定的.在使用钻头的情况下,由于钻头的形状及尺寸,精度,被钻孔之材质等,对于所钻孔的尺寸,精度有很大影响,所以使用本表之钻孔径,若有不当之处,应实际状况适当的变更钻头直径,本表依据2级牙制订.公制精螺纹规格标准径2级牙钻孔径最大最小M1.0×0.25 0.75 0.785 0.729M1.1×0.25 0.85 0.885 0.829M1.2×0.25 0.95 0.985 0.929M1.4×0.3 1.10 1.142 1.075M1.6×0.35 1.25 1.321 1.221M1.7×0.35 1.35 1.421 1.321M1.8×0.35 1.45 1.521 1.421M2.0×0.4 1.60 1.679 1.567M2.2×0.45 1.75 1.838 1.713M2.3×0.4 1.90 1.979 1.867M2.5×0.45 2.10 2.138 2.013M2.6×0.45 2.20 2.238 2.113M3.0×0.5 2.50 2.599 2.459M3.0×0.6 2.40 2.44 2.280M3.5×0.6 2.90 3.010 2.850M4.0×0.7 3.30 3.422 3.242M4.0×0.75 3.25 3.326 3.106M4.5×0.75 3.80 3.878 3.688M5.0×0.8 4.20 4.334 4.134M5.0×0.9 4.10 4.170 3.930M6.0×1.0 5.00 5.153 4.917M7.0×1.0 6.00 6.153 5.917M8.0×1.25 6.80 6.912 6.647M9.0×1.25 7.80 7.912 7.647M10×1.5 8.50 8.676 8.376M11×1.5 9.50 9.676 9.376M12×1.75 10.30 10.441 10.106 M14×2.0 12.00 12.210 11.735M16×2.0 14.00 14.210 13.835M18×2.5 15.50 15.744 15.294M20×2.5 17.50 17.744 17.294M22×2.5 19.50 19.744 19.294M24×3.0 21.00 21.252 2.752M27×3.0 24.00 24.252 23.752M30×3.5 26.50 26.771 26.211公制细螺纹规格标准径2级牙钻孔径最大最小M1.0×0.2 0.80 0.821 0.783M1.1×0.2 0.90 0.921 0.883M1.2×0.2 1.00 1.021 0.983M1.4×0.2 1.20 1.221 0.183M1.6×0.2 1.40 1.421 1.383M1.7×0.2 1.45 1.500 1.460M1.8×0.2 1.60 1.621 1.583M2.0×0.25 1.75 1.785 1.729M2.2×0.25 1.95 1.985 1.929M2.3×0.25 2.05 2.061 2.001M2.5×0.35 2.20 2.221 2.121M2.6×0.35 2.20 2.246 2.186M3.0×0.35 2.70 2.721 2.621M3.5×0.35 3.20 3.221 3.121M4.0×0.5 3.50 3.599 3.459M4.5×0.5 4.00 4.099 3.959M5×0.5 4.50 4.599 4.459M5.5×0.5 5.00 5.099 4.959M6.0×0.75 5.30 5.378 5.188M6.0×0.5 5.50 5.550 5.400M7.0×0.75 6.30 6.378 61.88M7.0×0.5 6.50 6.550 64.00M8.0×1.0 7.00 7.153 6.917M8.0×0.75 7.30 7.378 7.188M8×0.5 7.50 7.520 7.400M9×1.0 8.00 8.153 7.917M9×0.75 8.30 8.378 8.188M10×1.25 8.80 8.912 8.647M10×1.0 9.00 9.153 8.917M10×0.5 9.50 9.520 9.400M11×1.0 10.00 10.153 9.917M11×0.75 10.30 10.378 10.188 M11×1.5 10.50 10.676 10.376M12×1.25 10.80 10.912 10.647 公制细螺纹规格标准径2级牙钻孔径最大最小M12×1.0 11.00 11.153 10.917M12×0.5 11.50 11.520 11.4M14×1.5 12.50 12.676 12.376M14×1.0 13.00 13.153 12.917M15×1.5 13.50 13.676 13.376M15×1.0 14.00 14.153 13.917M16×1.5 14.50 14.676 14.376M16×1.0 15.00 15.153 14.917M17×1.5 15.50 15.676 15.376M17×1.0 16.00 16.153 15.917M18×2.0 16.00 16.210 15.835M18×1.5 16.50 16.670 16.376M18×1.0 17.00 17.153 16.917M20×2.0 18.00 18.210 17.835M20×1.5 18.50 18.676 18.376M20×1.0 19.00 19.153 18.917M20×2.0 20.00 20.210 19.835M22×1.5 20.50 20.676 20.376M22×1.0 21.00 21.153 20.917M24×2.0 22.00 22.210 21.835M24×1.5 22.50 22.676 22.376M24×1.0 23.00 23.153 22.917M25×2.0 23.00 23.210 22.835M25×1.5 23.50 23.676 23.376M25×1.0 24.00 24.153 23.917M26×1.5 24.50 24.676 24.376M27×2.0 25.00 25.210 24.835M27×1.5 25.50 25.676 25.376M27×1.0 26.00 26.153 25.917M28×2.0 26.00 26.210 25.835M28×1.5 26.50 26.676 26.376M28×1.0 27.00 27.153 26.917M30×3.0 27.00 27.252 26.752M30×2.0 28.00 28.210 27.835M30×1.5 28.50 28.676 28.376M32×2.0 30.00 30.210 29.835M32×1.5 30.50 30.676 30.376M33×3.0 30.00 30.252 29.752M33×2.0 31.00 31.210 30.835M33×1.5 31.50 31.376 31.376M35×1.5 33.50 33.676 33.376M36×3.0 33.00 33.252 32.752M36×2.0 34.00 34.210 33.835M36×1.5 34.50 34.676 34.376美制细螺纹规格(UNF) 标准径2级牙钻孔径最大最小番数牙外径NO.0-80(1.524) 1.25 1.305 1.182 NO.1-72(1.854) 1.55 1.612 1.474 NO.2-64(2.184) 1.85 1.912 1.756 NO.3-56(2.515) 2.10 2.197 2.025 NO.4-48(2.845) 2.40 2.458 2.271 NO.5-44(3.175) 2.70 2.740 2.551 NO.6-40(3.505) 2.90 3.022 2.820 NO.8-36(4.166) 3.50 3.606 3.404 NO.10-32(4.826) 4.10 4.165 3.963 NO.12-28(5.846) 4.60 4.724 4.496 1/4 -28 5.50 5.588 5.3605/16 -24 6.90 7.035 6.7823/8 -24 8.50 8.636 8.3827/16 -20 9.90 10.033 9.7291/2 -20 11.50 11.607 11.3299/16 -18 12.90 13.081 12.7515/8 -18 14.50 14.681 14.3513/4 -16 17.50 14.678 17.3237/8 -14 20.50 20.675 20.2701 -12 23.20 23.571 23.1141-1/8 -12 26.50 26.746 26.2891-1/4 -12 29.50 29.921 29.4641-3/8 -12 32.80 33.096 32.4641-1/2 -12 36.00 36.270 35.814无屑丝攻钻孔径规格精度等级RH4.5.6 RH7.8 RH9M1.0×0.25 0.86 0.88 -M1.1×0.25 0.96 0.98 -M1.2×0.25 1.06 1.08 -M1.4×0.3 1.24 1.25 -M1.6×0.35 1.41 1.43 -M1.7×0.35 1.51 1.53 -M1.8×0.35 1.61 1.63 -M2.0×0.4 1.78 1.80 -M2.2×0.45 1.95 1.98 -M2.3×0.4 2.08 2.10 -M2.5×0.45 2.25 2.28 -M2.6×0.45 2.35 1.38 -M3.0×0.5 2.73 2.75 -M3.0×0.6 3.17 3.20 -M4.0×0.7 3.62 3.65 3.69M5.0×0.8 4.56 4.60 4.64M6.0×1.0 5.45 5.50 5.55M7.0×1.0 6.45 6.50 6.55M8.0×1.25 7.31 7.38 7.44M10×1.5 9.18 9.25 9.32M10×1.25 9.31 9.38 9.44M12×1.75 11.04 11.12 11.21M12×1.25 11.31 11.38 11.44注:无槽丝攻之钻孔径,在上表所列之数值,由于被加工材料之材质、硬度、形状、尺寸等之影响,多少会有所变动，因此参考上表之同时,亦请增减若干.美制管螺纹规格(UNEF) 标准径2级牙钻孔径最大最小NO.12 -32 4.70 4.826 4.6231/4 -32 5.60 5.690 5.4865/16 -32 7.10 7.264 7.0873/8 -32 8.70 8.865 8.6617/16 -28 10.20 10.338 10.1351/2 -28 11.80 11.938 11.7099/16 -28 13.20 13.386 13.1325/8 -24 14.80 14.986 14.7323/4 -20 17.80 17.958 17.6787/8 -20 21.00 21.133 20.8531 -20 24.00 24.308 24.028美制粗螺纹规格(UNC) 标准径2级牙钻孔径番数牙外径最大最小NO.1-64(1.854) 1.55 1.582 1.425NO.2-56(2.184) 1.80 1.871 1.695NO.3-48(2.515) 2.10 2.146 1.941NO.4-40(2.845) 2.30 2.385 2.157NO.5-40(3.175) 2.60 2.697 2.487NO.6-32(3.505) 2.80 2.895 2.642 NO.8-32(4.166) 3.40 3.530 3.302 NO.10-24(4.826) 3.90 3.962 3.682 NO.12-24(5.846) 4.50 4.597 4.344 1/4 -20 5.10 5.257 4.9795/16 -18 6.60 6.731 6.4013/8 -16 8.00 8.153 7.9877/16 -14 9.40 9.500 9.1441/2 -13 10.80 11.023 10.5929/16 -12 12.20 12.446 11.9895/8 -11 13.60 12.868 13.3863/4 -10 16.20 16.840 16.3077/8 -9 19.50 19.761 19.1771 -8 22.20 22.606 21.9711-1/8 -7 25.00 25.349 24.6381-1/4 -7 28.20 28.524 27.8131-3/8 -6 30.80 31.115 30.3531-1/2 -6 34.00 34.290 33.5281-3/4 -5 39.50 39.827 38.9642 -4-1/2 45.20 45.593 44.679英制螺纹规格钻孔径硬材软材W1/8 - 40 2.65 2.60W5/32 - 32 3.25 3.20W3/16 - 24 3.75 3.70W1/4 - 20 5.10 5.00W5/16 - 18 6.60 6.50W3/8 - 16 8.00 7.90W7/16 - 14 9.40 9.30W1/2 - 12 10.70 10.50W9/16 - 12 12.30 12.00W5/8 - 11 13.70 13.50W3/4 - 10 16.70 16.50W7/8 - 9 19.50 19.30W1 - 8 22.40 22.00W1-1/8 - 7 25.00 24.80W1-1/4 - 7 28.30 28.00英制管螺纹规格标准径钻孔径最大最小PS1/16 -28 6.50 6.632 6.490PS1/8 -28 8.50 8.637 8.495PS1/4 - 19 11.40 11.549 11.341PS3/8 - 19 15.00 15.054 14.846PS1/2 - 14 18.50 18.773 18.489PS3/4 - 14 24.00 24.259 23.975PS1 - 11 30.20 30.471 30.111PS1-1/4 -11 38.80 39.132 38.772PS1-1/2 -11 44.80 45.025 44.665PS2 - 11 56.50 56.836 56.476英制管螺纹规格标准径有效牙部之长度(最小)中之母螺牙内径标准长度(最小)中之母螺牙内径使用绞刀时不用绞刀时PT1/16 -28 6.10 6.2 6.244 6.384PT1/8 -28 8.10 8.2 8.249 8.388PT1/4 -19 10.70 11 10.962 11.174PT3/8 -19 14.20 14.5 14.448 14.658PT1/2 -14 17.60 18 17.979 18.263PT3/4 -14 23.00 23.5 23.378 23.663Pt1 -11 29.00 29.5 29.459 29.822PT1-1/4 -11 37.50 38 37.976 38.339PT1-1/2 -11 43.40 44 43.869 44.232Pt2 -11 54.90 55.5 55.412 55.844美制螺纹滚造径规格钻孔径NPT NPS使用绞刀时不用绞刀时1/16 -27 6.1 6.25 6.351/8 -27 8.33 8.43 8.741/4 -18 10.72 11.13 11.133/8 -18 14.27 14.27 14.681/2 -14 17.48 17.86 18.263/4 -14 22.63 23.01 23.421 -11-1/2 28.58 28.98 29.361-1/4-11-1/2 37.31 37.69 38.11-1/2-11-1/2 43.66 44.04 44.452 -11-1/2 55.58 55.96 56.36英制螺纹滚造径规格滚造径W 3/16 - 24 4.08 - 4.05W 1/4 - 20 5.51 - 5.46W 5/16 - 18 7.01 - 6.95W 3/8 - 16 8.48 - 8.41W 7/16 - 14 9.92 - 9.85W 1/2 - 12 11.31 - 11.24W 9/16 -12 12.89 - 12.82规格滚造径M3.0×0.5 2.63 2.60M3.0×0.6 2.56 2.53M3.5×0.6 3.06 3.03M4.0×0.7 3.49 3.45M4.0×0.75 3.45 3.41M4.5×0.75 3.96 3.92M5.0×0.8 4.43 4.38M5.0×0.9 4.36 4.31M6.0×1.0 5.30 5.25M7.0×1.0 6.30 6.25M8.0×1.0 7.28 - 7.23M8.0×1.25 7.12 - 7.07M9.0×1.25 8.12 - 8.07M10×1.25 9.10 - 9.04M10×1.5 8.97 - 8.91M11×1.5 9.97 - 9.91M12×1.5 10.92 - 10.87M12×1.75 10.79 - 10.73 M14×2.0 12.63 - 12.56M16×2.0 14.63 - 14.56M18×2.5 16.31 - 16.23M20×2.5 18.31 - 18.23M22×2.5 20.31 - 20.23针车用螺纹规格(UNC) 滚造径SM 1/8 40 2.735 -2.688 SM 1/8 44 2.769 -2.722 SM 9/64 40 3.128 -3.083 SM 11/64 40 3.855 -3.805 SM 3/16 32 4.205 -4.155 SM 3/16 28 4.143 -4.093 SM 7/32 32 5.003 -4.955 SM 15/64 28 5.325 -4.955 SM 1/4 40 5.890 -5.735 SM 1/4 28 5.721 -5.366 SM 9/32 28 6.528 -6.648 SM 11/32 28 8.092 -8.432 SM 3/8 29 8.880 -8.015 SM 7/16 30 10.466 -10.401 SM 7/16 16 10.037 -9.967 SM 1/2 20 11.819 -11.749 SM 9/16 20 13.400 -13.425规格(UNC) 滚造径NO.5-40 2.70 - 2.67NO.6-32 2.95 - 2.91NO.8-32 3.60 - 3.57NO.10-24 4.09 - 4.05NO.12-24 4.75 - 4.701/4 -20 5.50 - 5.455/16 -18 6.98 - 6.933/8 -16 8.45 - 8.407/16 -14 9.89 - 9.831/2 -13 11.39 - 11.329/16 -12 12.87 - 12.80美制细螺纹规格(UNF) 滚造径NO.5-44 2.73 - 2.70NO.6-40 3.05 - 3.02NO.8-36 3.66 - 3.63NO.10-32 4.26 - 4.80NO.12-28 4.84 - 4.801/4 -28 5.72 - 5.685/16 -24 7.20 - 7.163/8 -24 8.79 - 8.747/16 -20 10.23 - 10.181/2 -20 11.82 - 11.76来源：直观学机械推荐阅读1.钢价惨烈下跌风暴即将来临?不要以为和你没关系2.世界名刀大全，简直太漂亮了免责声明：本文系网络转载，版权归原作者所有。
最全螺纹底孔查询表
规格
标准径
2级牙钻孔径 最大 最小
1/4 -32 5.6 5.689 5.487
牙 套 螺 纹攻 用
规格
标准径
下孔径 最大 最小
M10*1.5 10.5 10.62 10.37
美制管螺纹
钻孔径
规格
1-1/4 -111/2
NPT
使用铰刀时
37.31
英制管螺纹(PS,PF,PT)
规格
标准径
2 - 11 PF 57
NPT
不用铰刀时
37.69
NPS
38.1
螺纹(PS,PF,PT)
钻孔径
最大
最小
57.296 56.656
针车用螺纹
规格
标准径
最大
最小
SM1/16 -80 1.25 1.281 1.211
美制特殊螺纹(UNS)
规格（2B内螺纹) 螺纹外径
钻孔径
最大
最小
1/4-36 UNS 2B 6.3标准径
2级牙钻孔径 最大 最小
M1.4*0.3 1.1 1.142 1.075
螺纹查
公制细螺纹
规格
标准径
M4.5*0.5
4
询
美制粗螺纹(UNC)
规格
标准径
2级牙钻孔径 最大 最小
3/8 -16
8 8.153 7.798
美制细螺纹(UNF)
规格
标准径
3/8 -24 8.5
美制特细螺纹(UNEF)
纹查询表
公制细螺纹
2级牙钻孔径
最大
最小
公制迫牙丝攻钻孔径
规格
精度
最大
最小
4.099 3.959
最全的螺纹孔径对照表(公制-英制)
公制粗螺纹
规格
M1.0*0.25 M1.1*0.25 M1.2*0.25 M1.4*0.3 M1.6*0.35 M1.7*0.35 M1.8*0.35 M2.0*0.4 M2.2*0.45 M2.3*0.4 M2.5*0.45 M2.6*0.45 M3.0*0.5 M3.0*0.6 M3.5*0.6 M4.0*0.7 M4.0*0.75 M4.5*0.75 M5.0*0.8 M5.0*0.9 M6.0*1.0 M7.0*1.0 M8.0*1.25 M9.0*1.25 M10*1.5 M11*1.5 M12*1.75 M14*2.0 M16*2.0 M18*2.5 M20*2.5 M22*2.5 M24*3.0 M27*3.0 M30*3.5
2级牙钻孔径 最大 最小 11.153 10.917 11.520 11.400 12.676 12.376 13.153 12.917 13.676 13.376 14.153 13.917 14.676 14.376 15.153 14.917 15.676 15.376 16.153 15.917 16.210 15.835 16.676 16.376 17.153 16.917 18.210 17.835 18.676 18.376 19.153 18.917 20.210 19.835 20.676 20.376 21.153 20.917 22.210 21.835 22.676 22.376 23.153 22.917 23.210 22.835 23.676 23.376 24.153 23.917 24.676 24.376 25.210 24.835 25.676 25.376 26.153 25.917 26.210 25.835 26.676 26.376 27.153 26.917 27.252 26.752 28.210 27.835 28.676 28.376 29.153 28.917 30.210 29.835 30.676 30.376 30.252 29.752 31.210 30.835 31.676 31.376 33.676 33.376 33.252 32.752 34.210 33.835 34.676 34.376
英制管螺纹美制管螺纹对照表
英制管螺纹美制管螺纹对照表英制管螺纹美制管螺纹对照表(若需要原件请留言) 2008-06-03 16:57分类:专业知识字号: 大中小英制管螺纹美制管螺纹对照表英制管螺纹英制管螺纹美制管螺纹钻孔径标准径有交牙钻孔径标准长部之长度(最NPT 规格标准径规格不用纹刀度(最小)中规格最大最小使用纹刀时小)中之毋螺NPS 时之毋螺牙内径使用绞刀时不用绞刀时牙内径PS 1/16-28 6.50 6.632 6.490 PT 1/16-28 6.10 6.20 6.244 6.384 1/16 - 27 6.10 6.25 6.35 PS 1/8-28 8.50 8.637 8.495 PT 1/8-28 8.10 8.20 8.249 8.388 1/8 - 27 8.33 8.43 8.7411.0PS 1/4-19 11.40 11.549 11.341 PT 1/4 -19 10.70 10.962 11.174 1/4 - 18 10.72 11.13 11.13 014.5PS 3/8-19 15.00 15.054 14.846 PT 3/8 -19 14.20 14.448 14.658 3/8 - 18 14.27 14.27 14.68 018.0PS 1/2-14 18.50 18.773 18.489 PT 1 /2-14 17.60 17.979 18.263 1/2 - 14 17.48 17.86 18.26 023.5PS 3/4-14 24.00 24.259 23.975 PT 3/4 -14 23.00 23.378 23.663 3/4 - 14 22.63 23.01 23.42 029.5PS 1-11 30.20 30.471 30.111 PT 1 -11 29.00 29.459 29.822 1 - 11-1/2 28.58 28.98 29.36 0electricity at no cost, revenue from electricity sales. Poverty alleviation to the removal, to desperate farmers out of poverty, in conjunction with urbanization, new communities are centrally placed. Poverty in the enterprise, enterprise more powerful, more social responsibility, they should allow more people to enjoy the fruits of development. Conditions to encourage private enterprises to establish Charity Fund for poverty alleviation, employment, grants, financial aid and other forms of poverty alleviation activities, let povertyalleviation aid corporate social responsibility in the specific embodiment, the proper meaning of giving back to the community. Finally reveals to implement poverty alleviation policies, older age, incapacity, cannot be achieved through industry support and employment support, such as poverty, children and unable to support the poor, Lo-Fi policyreveals the role to play, eventually incorporated into the low range,and fundamentally solve the problem of poverty. (C) establishing and perfecting retreat mechanism. Poverty alleviation is a dynamic project, we must strengthen the farmers ' information management, dynamic management of poor, really "poor" no place to hide, "poverty" a timely exit, "poor" and "return to the poor" get maximum support and help. To build up the information network system of the poor, poverty the basic information and dynamic entry to the system, to implement dynamic management. According to pro-poor development, timely adjustment on38.0PS 1-1/4-11 38.80 39.132 38.772 PT 1 -1/4-11 37.50 37.976 38.339 1-1/4-11-1/2 37.31 37.69 38.10 044.0PS 1-1/2-11 44.80 45.025 44.665 PT 1 -1/2-11 43.40 43.869 44.232 1-1/2-11-1/2 43.66 44.04 44.45 055.5PS 2 - 11 56.50 56.836 56.476 PT 2 - 11 54.90 55.412 55.844 0NPT螺纹PT螺纹G螺纹和公制螺纹的区别NPT，PT，G 都是管螺纹(( PS——日本管螺纹 )NPT 是 National (American) Pipe Thread 的缩写，属于美国标准的 60 度锥管螺纹，用于北美地区(国家标准可查阅 GB/T12716-1991 PT 是 Pipe Thread 的缩写，是 55 度密封圆锥管螺纹，属惠氏螺纹家族，多用于欧洲及英联邦国家(常用于水及煤气管行业，锥度规定为 1:16( 国家标准可查阅 GB/T7306-2000G 是 55 度非螺纹密封管螺纹，属惠氏螺纹家族(标记为 G 代表圆柱螺纹(国家标准可查阅 GB/T7307-2001另外螺纹中的1/4、1/2、1/8 标记是指螺纹尺寸的直径，单位是英吋(行内人通常用分来称呼螺纹尺寸，一吋等于,分，1/4 吋就是,分，如此类推(G 就是管螺纹的统称(Guan)，55，60度的划分属于功能性的，俗称管圆。
公制美制英制螺纹对照表
公制/美制/英制螺纹对照表A型美制螺纹（UNF）常用规格外螺纹螺纹-4 9/16"-19牙 14.28 13.08 -6 11/16''-16 17.46 16.1-8 13/16''-16 20.64 19.28-10 1''-14 25.40 23.57-12 1(3/16)''-12 30.00 28.32 -16 1(7/16)''-12 36.51 34.67 -20 1(11/16)''-12 42.86 41.02C型JIC37度美制UNF螺纹常用规格-4 7/16”-20 11.11 10.03-5 1/2”-20 12.70 11.32-6 9/16”-18 14.28 13.08-8 3/4”-16 19.00 17.68-10 7/8”-14 22.22 20.68-12 1(1/16)"-12 26.98 25.15 -16 1(5/16)"-12 33.33 31.5 -20 1(5/8)"-12 41.28 39.44 -24 1(7/8)"-12 47.62 45.8-32 2(1/2)"-12 63.5 61.67英制圆柱管螺纹（BSPP）常用规格-4 1/4”-19 13.157 11.55-6 3/8”-19 16.662 14.95-8 1/2”-14 20.955 18.63-12 3/4”-14 26.441 24.11-16 1”-11 33.249 30.29-20 1(1/4)''-11 41.91 38.95英制圆锥管螺纹（BSPT）常用规格基面大径基准距离1/4”-19 13.157 63/8”-19 16.662 6.41/2”-14 20.955 8.23/4”-14 26.441 9.51”-11 33.249 10.41(1/4)''-11 41.91 12.7美制圆锥管螺纹（NPT）1/8”-27 10.24 41/4”-18 13.60 43/8”-18 17.04 4.321/2”-14 21.22 4.483/4”-14 26.57 4.751”-11(1/2)” 33.22 4.61(1/4)”-11.5 41.96 4.832007-4-20 16:33评论(7)3/8-16 0.3643 0.3737 0.3287 0.3331 0.2970 8.40 8.44(0.375-16) 9.2532 9.4920 8.3490 8.4607 7.54387/16-14 0.4258 0.4361 0.3850 0.3897 0.3485 9.83 9.87(0.4375-14) 10.8153 11.0769 9.7790 9.8984 8.85191/2-13 0.4876 0.4985 0.4435 0.4485 0.4041 11.34 11.38(0.50-13) 12.3850 12.6619 11.2649 11.3919 10.26419/16-12 0.5495 0.5609 0.5016 0.5068 0.4587 12.80 12.84(0.5625-12) 13.9573 14.2469 12.7406 12.8727 11.65105/8-11 0.6113 0.6234 0.5589 0.5644 0.5119 14.27 14.32 (0.625-11) 15.5270 15.8344 14.1961 14.3358 13.00233/4-10 0.7353 0.7482 0.6773 0.6832 0.6255 17.28 17.33 (0.750-10) 18.6766 19.0043 17.2034 17.3533 15.88777/8-9 0.8592 0.8731 0.7946 0.8009 0.7368 20.27 20.32(0.875-9) 21.8237 22.1767 20.1828 20.3429 18.71471"-8 0.9830 0.9980 0.9100 0.9168 0.8446 23.22 23.27(1.000-8) 24.9682 25.3492 23.1140 23.2867 21.45281.螺胚直径指滚丝前的尺寸，数值为依经验公式计算而得，在实践中需验证。
螺纹底孔直径查询尺寸表
螺纹标准介绍管螺纹的标准：管螺纹：主要用来进行管道的连接，使其外螺纹的配合紧密，有直管和锥管两种。
常见的管螺纹主要包括以下几种：NPT、PT、G等。
1:NPT 螺纹是美国标准的60度锥管螺纹 2:PT(BSPT) 螺纹是欧洲和英联邦55度密封圆锥管螺纹 3:G 螺纹是 55度非螺纹密封管螺纹 4：ZG 螺纹是1）NPT是National(American)PipeThread的缩写，属于美国标准的60度椎管螺纹，用于北美地区，国标查阅GB/T12716-1991。
2）PT（BSPT）是PipeThread的缩写，是55度密封圆椎管螺纹，属于惠氏螺纹家族，多用于欧洲及英联邦国家，常用于水及煤气管行业，锥度1:16，国标查阅GB/T7306-2000。
国叫法为ZG.。
3）G是55度非螺纹密封管螺纹，属惠氏螺纹家族。
标记为G代表圆柱螺纹。
国标查阅GB/T7307-2001。
公制螺纹与英制螺纹的区别：公制螺纹用螺距来表示，美英制螺纹用每英寸的螺纹牙数来表示；公制螺纹是60度等边牙型，英制螺纹是等腰55度牙型，美制螺纹为等腰60度牙型。
公制螺纹用公制单位（如mm），美英制螺纹用英制单位（如英寸）；“行人”通常用“分”来称呼螺纹尺寸，一英寸等于8分，1/4英寸就是2分，以此类推。
另外还有：ISO—公制螺纹标准60度；UN—统一螺纹标准60度；API—美国石油管螺纹标准60度；W—英国惠氏螺纹标准55度；NPT BSP螺纹技术---- NPT，PT，G螺纹的区别NPT，PT，G各种螺纹的区别NPT，PT，G 都是管螺纹．NPT是National(American)PipeThread的缩写，属于美国标准的60度锥管螺纹，用于北美地区．国家标准可查阅GB/T12716-1991PT是PipeThread的缩写，是55度密封圆锥管螺纹，属惠氏螺纹家族，多用于欧洲及英联邦国家．常用于水及煤气管行业，锥度规定为1:16．国家标准可查阅GB/T7306-2000G是 55 度非螺纹密封管螺纹，属惠氏螺纹家族．标记为G代表圆柱螺纹．国家标准可查阅 GB/T7307-2001另外螺纹中的1/4、1/2、1/8标记是指螺纹尺寸的直径，单位是英寸．行人通常用分来称呼螺纹尺寸，一等于８分，1/4?就是２分，如此类推．G就是管螺纹的统称(Guan)，55，60度的划分属于功能性的，俗称管圆。
美制英制公制螺纹孔尺寸表
螺纹规格-美制、英制、公制公制/美制/英制螺纹对照表给大家分享一下 A型美制螺纹（UNF）常用规格牙型角60外螺纹内螺纹 -4 9/16"-19牙 14.28 13.08 -6 11/16''-16 17.46 16.1 -8 13/16''-16 20.64 19.28 -10 1''-14 2 5.40 23.57 -12 1(3/16)''-12 30.00 28.32 -16 1(7/16)''-12 36.51 34.67 -20 1(11/16)' '-12 42.86 41.02 C型JIC37度美制UNF螺纹常用规格牙型角60-4 7/16”-20 11.11 10.03 -5 1/2”-20 12.70 11.32-6 9/16”-18 14.28 13.08 -83/4”-16 19.00 17.68 -10 7/8”-14 22.22 20.68 -12 1(1/16)"-12 26.98 25.15 -16 1 (5/16)"-12 33.33 31.5 -20 1(5/8)"-12 41.28 39.44 -24 1(7/8)"-12 47.62 45.8 -32 2(1/2)"-12 63.5 61.67 英制圆柱管螺纹（BSPP）常用规格牙型角55-4 1/4”-19 13.157 11.55 -6 3/8”-19 16.662 14.95 -8 1/2”-14 20.955 18.63 -12 3/4”-14 26.441 24.11 -16 1”-11 33.249 30.29 -20 1(1/4)''-11 41.91 38.95 英制圆锥管螺纹（BSPT）常用规格牙型角55基面大径基准距离1/4”-19 13.157 6 3/8”-19 16.662 6.4 1/2”-14 20.955 8.2 3/4”-14 26.441 9.5 1”-11 33.249 10.4 1(1/4)''-11 41.91 12.7 美制圆锥管螺纹（NPT）牙型角601/8”-27 10.24 4 1/4”-18 13.60 4 3/8”-18 17.04 4.32 1/2”-14 21.22 4.48 3/4”-14 26.57 4.75 1”-11(1/2)” 33.22 4.6 1(1/4)”-11.5 41.96 4.83螺纹的一般知识第一章国标螺纹的一般知识一. 螺纹的分类1. 螺纹分内螺纹和外螺纹两种；2. 按牙形分可分为：1）三角形螺纹2）梯形螺纹3）矩形螺纹4）锯齿形螺纹；3. 按线数分单头螺纹和多头螺纹；4. 按旋入方向分左旋螺纹和右旋螺纹两种, 右旋不标注，左旋加LH，如M24×1.5LH；5. 按用途不同分有：米制普通螺纹、用螺纹密封的管螺纹、非螺纹密封的管螺纹、60°圆锥管螺纹、米制锥螺纹等二. 米制普通螺纹1. 米制普通螺纹用大写M表示，牙型角2α=60°（α表示牙型半角）；2. 米制普通螺纹按螺距分粗牙普通螺纹和细牙普通螺纹两种；2.1. 粗牙普通螺纹标记一般不标明螺距，如M20表示粗牙螺纹；细牙螺纹标记必须标明螺距，如M30×1.5表示细牙螺纹、其中螺距为1.5。
- 1、下载文档前请自行甄别文档内容的完整性，平台不提供额外的编辑、内容补充、找答案等附加服务。
- 2、"仅部分预览"的文档,不可在线预览部分如存在完整性等问题,可反馈申请退款(可完整预览的文档不适用该条件!)。
- 3、如文档侵犯您的权益，请联系客服反馈,我们会尽快为您处理(人工客服工作时间：9:00-18:30)。
8
83
18
6.6
16
8
14
9.4
13
10.8
12
12.2
11
13.5
10
16.5
9
19.5
8
22.25
7
25
7
28
6
30.75
6
34
5
39.5
4.5
45
4.5
51.5
4
57.25
4
63.5
4
70
28
5.5
24
6.9
24
8.5
20
9.9
20
11.5
18
12.9
18
14.5
16
17.5
14
20.4
12
23.25
M1 0.25 0.7(0.75) M2.5 0.35 2.1(2.15)
1
23
1/16
60
M1.1 0.25 0.8(0.85) M3 0.35 2.6(2.65) M24 1.5 22.5
3/32
48
M1.2 0.25 0.9(0.95) M3.5 0.35 3.1(3.15)
2
22
1/8
40
M1.4 0.3
编号
#0-80 #1-72 #2-64 #3-56 #4-48 #5-44 #6-40 #8-36 #10-32 #12-28
美制小牙孔幼牙(NC)
牙距(per inch) 底孔直径(MM) 底孔深度(MM)
80
1.2(1.25)
4
72
1.5(1.55)
5
64
1.9
6
56
2.1(2.15)
7
48
2.4
美制小牙孔标准牙(NC)
牙距(per inch) 底孔直径(MM) 底孔深度(MM)
64
1.5(1.55)
5
56
1.8(1.85)
6
48
2.1
7
40
2.3(2.35)
8
40
2.6(2.65)
9
32
2.8(2.85)
10
32
3.5
11
24
3.91324Fra bibliotek4.5
15
螺纹深度(MM) 4
4 5 6 6 7 8 10 11
3
39
M52 5
47
2
18
4
38
M56 5.5
50.5
1
21
1.5 43.5
M22 1.5
20.5
2
M45
43
2
20
3
42
4
41
1.15
1.8
2.6
3.1
3.6
32
4
4.4
28
4.7
5.1
26
5.4
5.8
26
6.2
6.5
22
6.8
7.9
20
8.3
9.3
18
9.8
10.5
16
11.2
12
16
12.7
13.5
12
M5 0.8
4.2
0.75 9.2
1.5 28.5
5/8
11
M30
M6 1
5
M10 1
9
2
28
11/16
11
M7 1
6
1.25 8.8
3
27
3/4
10
M8 1.25 6.8
0.75 10.2
1.5
30.5
13/16
10
M11
M32
M9 1.25 7.8
1
10
2
30
7/8
9
M10 1.5
8.5
1
11
9/32
20
M2.5 0.45 2.0(2.05) M7 0.75 6.2
2
25
5/16
18
M3 0.5
2.5
0.75 7.2
1
27
3/8
16
M8
M3.5 0.6
2.9
1
7
M28 1.5 26.5
7/16
14
M4 0.7
3.3
M4.5 0.75 3.7
M9 0.75
8.2
1
8
2
26
1
29
1/2
12
9/16
57
11
63.3
11
72.8
11
79.1
11
85.5
螺纹深度(MM)
3 4 4 5 6 6 7 8 10 11
英制锥喉牙 Rc,BSPT
牙距(per inch) 底孔直径(MM)
28
8.6
19
11.5
19
15
14
18.5
14
24
11
30.25
11
39
11
45
11
56.5
11
71.4
美制喉牙 NPS
牙距(per inch) 底孔直径(MM)
14
14
15
14
15.75
6.5
12
17
18
12
18.5
19.25
11
20
20.75
11
21.75
22
10
23
24.75
9
26
27.75
9
29
30.5
8
32
33.5
8
35
35.5
8
37.5
39
7
40
41.5
7
43
44.5
7
46.5
50
6
52
56.5
6
58.5
62
6
64.5
68.5
5
69.75
20
5.1
M17 1 1.5
16 15.5
3
36
2.1/4
4
1.5 38.5
2.1/2
4
M36 4
32
1
17
M40 2
38
2.3/4
3.5
M39 4
35
M18 1.5
16.5
3
37
3"
3.5
M42 4.5
37.5
2
16
1.5 40.5
M45 4.5
40.5
1
19
2
40
M42
M48 5
43
M20 1.5
18.5
34
1.1/2
6
M20 2.5
17.5
1
14
3
33
1.5/8
5
M15
M22 2.5
19.5
1.5
13.5 M38 1.5 36.5
1.3/4
5
M24 3 M27 3
21
1
15
1.5
37.5
1.7/8
4.5
M16
24
1.5
14.5 M39 2
37
2"
4.5
M30 3.5 M33 3.5
26.5 29.5
1.5 31.5
9
M11 1.5
9.5
M12 1.25 10.8 M33 2
31
1"
8
M12 1.75 10.2
1.5
10.5
3
30
1.1/8
7
M14 2
12
1
13
M35 1.5
33.5
1.1/4
7
M16 2
14
M14 1.25 12.8
1.5
34.5
1.3/8
6
M18 2.5
15.5
1.5
12.5 M36 2
公 制,英 制,美 制 螺 纹 标 准
公制标准牙
公制幼牙
尺寸
英制标准牙 BSW
英制幼牙 BSF
美制标准牙 UNC
美制幼牙 UNF
美制幼牙 UNEF
尺寸 牙距(MM) 底孔直径(MM) 尺寸 牙距(MM) 底孔直径(MM) 尺寸 牙距(MM) 底孔直径(MM) 英制(tach) 牙距(per inch) 底孔直径(MM) 牙距(per inch) 底孔直径(MM) 牙距(per inch) 底孔直径(MM) 牙距(per inch) 底孔直径(MM) 牙距(per inch) 底孔直径(MM)
8
44
2.7
9
40
2.9(2.95)
10
36
3.5
11
32
4.1
13
28
4.7
15
英制喉牙 G,BSP
牙距(per inch) 底孔直径(MM)
28
8.8
19
11.8
19
15.25
14
19
14
21
14
24.5
14
28.25
11
30.75
11
35.5
11
39.5
11
42
11
45
11
49.6
11
51
11
12
26.5
12
29.5
12
32.75