电解电容规格书
- 1、下载文档前请自行甄别文档内容的完整性,平台不提供额外的编辑、内容补充、找答案等附加服务。
- 2、"仅部分预览"的文档,不可在线预览部分如存在完整性等问题,可反馈申请退款(可完整预览的文档不适用该条件!)。
- 3、如文档侵犯您的权益,请联系客服反馈,我们会尽快为您处理(人工客服工作时间:9:00-18:30)。
样品承认书
SPECIFICATION FOR APPROV AL 客户:
(Customer)
品名: 铝电解电容器
(Product Name)
(Series) 日
期:2010 年月日
(Date)
贵公司承认:
Approval Signature
批准: 审核: 制作:
Approved Checked Prepared
电容器有限公司
CAPACITOR CO.,LTD.
地址:
电话传真 (FAX)
邮编(P.C.):
网址 (Internet):
Parts lists 物料清单 :
RT1 Series Type ( 系列 )
(105℃ ,1000H)
Electrical Requirements 电解电容器规格书
Capacitance Tolerance 容量偏差
±20% at 120Hz,20℃
After DC Voltage is applied to capacitor through the series protective resistance(1K Ω ),and then terminal voltage may reach the rated working voltage. The leakage current when measured after 2 minutes (6.3-400V)shall be below the value of the following equation.
串联(1K Ω)保护电阻后,对产品施加额定直流工作电压 (6.3~400V) 两分钟后,漏电
标称容量大于 1000μ F 时,每增加 1000μ F ,损耗角正切值增加 0.02。
Operation
Temperature
2 Range 工作温度
6.3V~100V -40℃~+105℃
160V~400V -25℃~+105 ℃
Rated Working V
oltage
And Surge Voltage
额定电压与 浪涌电压
Leakage
Current 漏电流
Where
Voltage(V
I=Leakage Current( μ A) C=Capacitance(μF) V=Rated DC Working
Dissipation Factor 损耗角正切值 (at
Endurance characteristic 特性检测 :
10
1. The test is about lead tabs strength. 1. 本测试主要测试引出端的强度 .
2. Tension Test: The lead tabs shall not be broken or any malformed condition after fixing capacitor vertically and pressing the following weight on the lead tabs of capacitor for 10 ± 1 secs. 2. 拉力测试:垂直固定电容器后,在引出端施加以下重量 10±1 秒钟,引出端不允 许出现任何损伤和变形。
3. Bending Test: The capacitor is held in vertical position. Attach a weight to the lead tabs, slowly rotate the capacitor 90 ℃ to a same way in the opposite direction. Repeat it again(5secs per cycle). The lead tabs shall not be broken or cracked.
3. 弯曲测试 :竖直放置电容器, 在其引出端悬挂下表重量的重物, 转动电容器 90 度, 恢复后,向相反方向转动 90度,再恢复为一个周期,重复 1次(每个循环 5秒钟 )。 引线不会损伤破损。
9 Mechanical Characteristics Test 引出端的强度
10
Satisfies Characteristic of GB2693 , IEC383 、 IEC384
Standards 引用标准
11.Diagram of Dimensions 尺寸图 :
(mm)
D ± 0.5 ±1.0
5 6or6.3 8 10 13 1
6 19
F±0.5 2.0 2.5 3.5 5.0 5.0 7.5 7.5 L ± 2.0(max) 11 11 12 13,16,20 20,25 25,31 35,40 d± 0.05 0.5 0.5 0.5or0.6 0.6 0.8
12. Case Size and Ripple Current
D×L(mm)
μwv F mA
6.3 ( 0J )
10 ( 1A ) 16 ( 1C ) 25 ( 1E ) 35 ( 1V ) 50 ( 1H ) 63 ( 1J ) Φ D ×L mA ΦD ×L mA Φ D ×L mA ΦD×L mA Φ D ×L mA ΦD×L mA ΦD ×L mA
0.1 ( 0R1) 5×11 3
0.22 ( R22) 5×11 4
0.33 ( R33) 5×11 5
0.47 ( R47) 5×11 6
1.0 ( 010) 5×119
2.2 ( 2R2) 5×1111
3.3 ( 3R3) 5×1115
4.7 ( 4R7) 5×1118 5×1120 10 (100) 5×1120 5×1125 5×1125 5×1125 5×1130 22 (220) 5×1130 5×1135 5×1135 5×1140 6.3×1150 33 (330) 5×1140 5×1140 5×1150 6.3×1160 8×1260 47 (470) 5×1145 5×1150 5×1150 6.3×1165 6.3×1173 8×1290 100 (101) 5×1160 5×1180 6.3×1180 6.3×1190 8×12110 8×12120 10×12150 220 (221) 6.3×11100 6.3×11110 8×12140 8×12150 10×13190 10×16240 10×20270 330 (331) 8×12120 8×12160 13×21302 10×13220 10×16260 10×20320 13×20380 470 (471) 8×12170 8×12190 10×13250 10×16290 10×20350 13×20430 13×25500 1000 (102) 10×13300 10×16360 10×20440 13×20540 13×25620 16×25790 16×31900 2200 (222) 13×20580 13×20620 13×25700 13×21725 16×311030 19×351230 19×401310 3300 (332) 13×20670 13×25800 16×25970 16×311120 19×351320 19×401400
4700 (472) 16×251000 16×251050 16×311240 19×351440
6800 (682) 16×251120 16×311300 19×35 1530 19×401630
10000 (103) 19×351320 19×351620 19×401730
尺寸和纹波电流